diff options
Diffstat (limited to 'drivers/net/dsa/microchip/ksz9477.c')
| -rw-r--r-- | drivers/net/dsa/microchip/ksz9477.c | 57 |
1 files changed, 51 insertions, 6 deletions
diff --git a/drivers/net/dsa/microchip/ksz9477.c b/drivers/net/dsa/microchip/ksz9477.c index dde5c65c2c..425e20daf1 100644 --- a/drivers/net/dsa/microchip/ksz9477.c +++ b/drivers/net/dsa/microchip/ksz9477.c @@ -427,6 +427,57 @@ void ksz9477_freeze_mib(struct ksz_device *dev, int port, bool freeze) mutex_unlock(&p->mib.cnt_mutex); } +int ksz9477_errata_monitor(struct ksz_device *dev, int port, + u64 tx_late_col) +{ + u32 pmavbc; + u8 status; + u16 pqm; + int ret; + + ret = ksz_pread8(dev, port, REG_PORT_STATUS_0, &status); + if (ret) + return ret; + if (!(FIELD_GET(PORT_INTF_SPEED_MASK, status) == PORT_INTF_SPEED_NONE) && + !(status & PORT_INTF_FULL_DUPLEX)) { + /* Errata DS80000754 recommends monitoring potential faults in + * half-duplex mode. The switch might not be able to communicate anymore + * in these states. + * If you see this message, please read the errata-sheet for more information: + * https://ww1.microchip.com/downloads/aemDocuments/documents/UNG/ProductDocuments/Errata/KSZ9477S-Errata-DS80000754.pdf + * To workaround this issue, half-duplex mode should be avoided. + * A software reset could be implemented to recover from this state. + */ + dev_warn_once(dev->dev, + "Half-duplex detected on port %d, transmission halt may occur\n", + port); + if (tx_late_col != 0) { + /* Transmission halt with late collisions */ + dev_crit_once(dev->dev, + "TX late collisions detected, transmission may be halted on port %d\n", + port); + } + ret = ksz_read8(dev, REG_SW_LUE_CTRL_0, &status); + if (ret) + return ret; + if (status & SW_VLAN_ENABLE) { + ret = ksz_pread16(dev, port, REG_PORT_QM_TX_CNT_0__4, &pqm); + if (ret) + return ret; + ret = ksz_read32(dev, REG_PMAVBC, &pmavbc); + if (ret) + return ret; + if ((FIELD_GET(PMAVBC_MASK, pmavbc) <= PMAVBC_MIN) || + (FIELD_GET(PORT_QM_TX_CNT_M, pqm) >= PORT_QM_TX_CNT_MAX)) { + /* Transmission halt with Half-Duplex and VLAN */ + dev_crit_once(dev->dev, + "resources out of limits, transmission may be halted\n"); + } + } + } + return ret; +} + void ksz9477_port_init_cnt(struct ksz_device *dev, int port) { struct ksz_port_mib *mib = &dev->ports[port].mib; @@ -1156,18 +1207,12 @@ void ksz9477_port_setup(struct ksz_device *dev, int port, bool cpu_port) /* enable broadcast storm limit */ ksz_port_cfg(dev, port, P_BCAST_STORM_CTRL, PORT_BROADCAST_STORM, true); - /* disable DiffServ priority */ - ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_DIFFSERV_PRIO_ENABLE, false); - /* replace priority */ ksz_port_cfg(dev, port, REG_PORT_MRI_MAC_CTRL, PORT_USER_PRIO_CEILING, false); ksz9477_port_cfg32(dev, port, REG_PORT_MTI_QUEUE_CTRL_0__4, MTI_PVID_REPLACE, false); - /* enable 802.1p priority */ - ksz_port_cfg(dev, port, P_PRIO_CTRL, PORT_802_1P_PRIO_ENABLE, true); - /* force flow control for non-PHY ports only */ ksz_port_cfg(dev, port, REG_PORT_CTRL_0, PORT_FORCE_TX_FLOW_CTRL | PORT_FORCE_RX_FLOW_CTRL, |