diff options
Diffstat (limited to 'drivers/net/dsa/mt7530.c')
| -rw-r--r-- | drivers/net/dsa/mt7530.c | 35 |
1 files changed, 11 insertions, 24 deletions
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c index 035a34b50f..2333f6383b 100644 --- a/drivers/net/dsa/mt7530.c +++ b/drivers/net/dsa/mt7530.c @@ -836,8 +836,7 @@ mt7530_get_strings(struct dsa_switch *ds, int port, u32 stringset, return; for (i = 0; i < ARRAY_SIZE(mt7530_mib); i++) - strncpy(data + i * ETH_GSTRING_LEN, mt7530_mib[i].name, - ETH_GSTRING_LEN); + ethtool_sprintf(&data, "%s", mt7530_mib[i].name); } static void @@ -1114,7 +1113,7 @@ mt7530_port_change_mtu(struct dsa_switch *ds, int port, int new_mtu) u32 val; /* When a new MTU is set, DSA always set the CPU port's MTU to the - * largest MTU of the slave ports. Because the switch only has a global + * largest MTU of the user ports. Because the switch only has a global * RX length register, only allowing CPU port here is enough. */ if (!dsa_is_cpu_port(ds, port)) @@ -2070,7 +2069,7 @@ mt7530_setup_mdio_irq(struct mt7530_priv *priv) unsigned int irq; irq = irq_create_mapping(priv->irq_domain, p); - ds->slave_mii_bus->irq[p] = irq; + ds->user_mii_bus->irq[p] = irq; } } } @@ -2164,7 +2163,7 @@ mt7530_setup_mdio(struct mt7530_priv *priv) if (!bus) return -ENOMEM; - ds->slave_mii_bus = bus; + ds->user_mii_bus = bus; bus->priv = priv; bus->name = KBUILD_MODNAME "-mii"; snprintf(bus->id, MII_BUS_ID_SIZE, KBUILD_MODNAME "-%d", idx++); @@ -2201,20 +2200,20 @@ mt7530_setup(struct dsa_switch *ds) u32 id, val; int ret, i; - /* The parent node of master netdev which holds the common system + /* The parent node of conduit netdev which holds the common system * controller also is the container for two GMACs nodes representing * as two netdev instances. */ dsa_switch_for_each_cpu_port(cpu_dp, ds) { - dn = cpu_dp->master->dev.of_node->parent; + dn = cpu_dp->conduit->dev.of_node->parent; /* It doesn't matter which CPU port is found first, - * their masters should share the same parent OF node + * their conduits should share the same parent OF node */ break; } if (!dn) { - dev_err(ds->dev, "parent OF node of DSA master not found"); + dev_err(ds->dev, "parent OF node of DSA conduit not found"); return -EINVAL; } @@ -2489,7 +2488,7 @@ mt7531_setup(struct dsa_switch *ds) if (mt7531_dual_sgmii_supported(priv)) { priv->p5_intf_sel = P5_INTF_SEL_GMAC5_SGMII; - /* Let ds->slave_mii_bus be able to access external phy. */ + /* Let ds->user_mii_bus be able to access external phy. */ mt7530_rmw(priv, MT7531_GPIO_MODE1, MT7531_GPIO11_RG_RXD2_MASK, MT7531_EXT_P_MDC_11); mt7530_rmw(priv, MT7531_GPIO_MODE1, MT7531_GPIO12_RG_RXD3_MASK, @@ -2718,7 +2717,7 @@ mt7531_mac_config(struct dsa_switch *ds, int port, unsigned int mode, case PHY_INTERFACE_MODE_RGMII_RXID: case PHY_INTERFACE_MODE_RGMII_TXID: dp = dsa_to_port(ds, port); - phydev = dp->slave->phydev; + phydev = dp->user->phydev; return mt7531_rgmii_setup(priv, port, interface, phydev); case PHY_INTERFACE_MODE_SGMII: case PHY_INTERFACE_MODE_NA: @@ -2824,15 +2823,6 @@ static void mt753x_phylink_mac_link_down(struct dsa_switch *ds, int port, mt7530_clear(priv, MT7530_PMCR_P(port), PMCR_LINK_SETTINGS_MASK); } -static void mt753x_phylink_pcs_link_up(struct phylink_pcs *pcs, - unsigned int mode, - phy_interface_t interface, - int speed, int duplex) -{ - if (pcs->ops->pcs_link_up) - pcs->ops->pcs_link_up(pcs, mode, interface, speed, duplex); -} - static void mt753x_phylink_mac_link_up(struct dsa_switch *ds, int port, unsigned int mode, phy_interface_t interface, @@ -2848,8 +2838,7 @@ static void mt753x_phylink_mac_link_up(struct dsa_switch *ds, int port, /* MT753x MAC works in 1G full duplex mode for all up-clocked * variants. */ - if (interface == PHY_INTERFACE_MODE_INTERNAL || - interface == PHY_INTERFACE_MODE_TRGMII || + if (interface == PHY_INTERFACE_MODE_TRGMII || (phy_interface_mode_is_8023z(interface))) { speed = SPEED_1000; duplex = DUPLEX_FULL; @@ -2921,8 +2910,6 @@ mt7531_cpu_port_config(struct dsa_switch *ds, int port) return ret; mt7530_write(priv, MT7530_PMCR_P(port), PMCR_CPU_PORT_SETTING(priv->id)); - mt753x_phylink_pcs_link_up(&priv->pcs[port].pcs, MLO_AN_FIXED, - interface, speed, DUPLEX_FULL); mt753x_phylink_mac_link_up(ds, port, MLO_AN_FIXED, interface, NULL, speed, DUPLEX_FULL, true, true); |