diff options
Diffstat (limited to 'drivers/net/wireless/ti/wl1251/tx.h')
-rw-r--r-- | drivers/net/wireless/ti/wl1251/tx.h | 217 |
1 files changed, 217 insertions, 0 deletions
diff --git a/drivers/net/wireless/ti/wl1251/tx.h b/drivers/net/wireless/ti/wl1251/tx.h new file mode 100644 index 0000000000..12f8b60709 --- /dev/null +++ b/drivers/net/wireless/ti/wl1251/tx.h @@ -0,0 +1,217 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ +/* + * This file is part of wl1251 + * + * Copyright (c) 1998-2007 Texas Instruments Incorporated + * Copyright (C) 2008 Nokia Corporation + */ + +#ifndef __WL1251_TX_H__ +#define __WL1251_TX_H__ + +#include <linux/bitops.h> +#include "acx.h" + +/* + * + * TX PATH + * + * The Tx path uses a double buffer and a tx_control structure, each located + * at a fixed address in the device's memory. On startup, the host retrieves + * the pointers to these addresses. A double buffer allows for continuous data + * flow towards the device. The host keeps track of which buffer is available + * and alternates between these two buffers on a per packet basis. + * + * The size of each of the two buffers is large enough to hold the longest + * 802.3 packet - maximum size Ethernet packet + header + descriptor. + * TX complete indication will be received a-synchronously in a TX done cyclic + * buffer which is composed of 16 tx_result descriptors structures and is used + * in a cyclic manner. + * + * The TX (HOST) procedure is as follows: + * 1. Read the Tx path status, that will give the data_out_count. + * 2. goto 1, if not possible. + * i.e. if data_in_count - data_out_count >= HwBuffer size (2 for double + * buffer). + * 3. Copy the packet (preceded by double_buffer_desc), if possible. + * i.e. if data_in_count - data_out_count < HwBuffer size (2 for double + * buffer). + * 4. increment data_in_count. + * 5. Inform the firmware by generating a firmware internal interrupt. + * 6. FW will increment data_out_count after it reads the buffer. + * + * The TX Complete procedure: + * 1. To get a TX complete indication the host enables the tx_complete flag in + * the TX descriptor Structure. + * 2. For each packet with a Tx Complete field set, the firmware adds the + * transmit results to the cyclic buffer (txDoneRing) and sets both done_1 + * and done_2 to 1 to indicate driver ownership. + * 3. The firmware sends a Tx Complete interrupt to the host to trigger the + * host to process the new data. Note: interrupt will be send per packet if + * TX complete indication was requested in tx_control or per crossing + * aggregation threshold. + * 4. After receiving the Tx Complete interrupt, the host reads the + * TxDescriptorDone information in a cyclic manner and clears both done_1 + * and done_2 fields. + * + */ + +#define TX_COMPLETE_REQUIRED_BIT 0x80 +#define TX_STATUS_DATA_OUT_COUNT_MASK 0xf + +#define WL1251_TX_ALIGN_TO 4 +#define WL1251_TX_ALIGN(len) (((len) + WL1251_TX_ALIGN_TO - 1) & \ + ~(WL1251_TX_ALIGN_TO - 1)) +#define WL1251_TKIP_IV_SPACE 4 + +struct tx_control { + /* Rate Policy (class) index */ + unsigned rate_policy:3; + + /* When set, no ack policy is expected */ + unsigned ack_policy:1; + + /* + * Packet type: + * 0 -> 802.11 + * 1 -> 802.3 + * 2 -> IP + * 3 -> raw codec + */ + unsigned packet_type:2; + + /* If set, this is a QoS-Null or QoS-Data frame */ + unsigned qos:1; + + /* + * If set, the target triggers the tx complete INT + * upon frame sending completion. + */ + unsigned tx_complete:1; + + /* 2 bytes padding before packet header */ + unsigned xfer_pad:1; + + unsigned reserved:7; +} __packed; + + +struct tx_double_buffer_desc { + /* Length of payload, including headers. */ + __le16 length; + + /* + * A bit mask that specifies the initial rate to be used + * Possible values are: + * 0x0001 - 1Mbits + * 0x0002 - 2Mbits + * 0x0004 - 5.5Mbits + * 0x0008 - 6Mbits + * 0x0010 - 9Mbits + * 0x0020 - 11Mbits + * 0x0040 - 12Mbits + * 0x0080 - 18Mbits + * 0x0100 - 22Mbits + * 0x0200 - 24Mbits + * 0x0400 - 36Mbits + * 0x0800 - 48Mbits + * 0x1000 - 54Mbits + */ + __le16 rate; + + /* Time in us that a packet can spend in the target */ + __le32 expiry_time; + + /* index of the TX queue used for this packet */ + u8 xmit_queue; + + /* Used to identify a packet */ + u8 id; + + struct tx_control control; + + /* + * The FW should cut the packet into fragments + * of this size. + */ + __le16 frag_threshold; + + /* Numbers of HW queue blocks to be allocated */ + u8 num_mem_blocks; + + u8 reserved; +} __packed; + +enum { + TX_SUCCESS = 0, + TX_DMA_ERROR = BIT(7), + TX_DISABLED = BIT(6), + TX_RETRY_EXCEEDED = BIT(5), + TX_TIMEOUT = BIT(4), + TX_KEY_NOT_FOUND = BIT(3), + TX_ENCRYPT_FAIL = BIT(2), + TX_UNAVAILABLE_PRIORITY = BIT(1), +}; + +struct tx_result { + /* + * Ownership synchronization between the host and + * the firmware. If done_1 and done_2 are cleared, + * owned by the FW (no info ready). + */ + u8 done_1; + + /* same as double_buffer_desc->id */ + u8 id; + + /* + * Total air access duration consumed by this + * packet, including all retries and overheads. + */ + u16 medium_usage; + + /* Total media delay (from 1st EDCA AIFS counter until TX Complete). */ + u32 medium_delay; + + /* Time between host xfer and tx complete */ + u32 fw_hnadling_time; + + /* The LS-byte of the last TKIP sequence number. */ + u8 lsb_seq_num; + + /* Retry count */ + u8 ack_failures; + + /* At which rate we got a ACK */ + u16 rate; + + u16 reserved; + + /* TX_* */ + u8 status; + + /* See done_1 */ + u8 done_2; +} __packed; + +static inline int wl1251_tx_get_queue(int queue) +{ + switch (queue) { + case 0: + return QOS_AC_VO; + case 1: + return QOS_AC_VI; + case 2: + return QOS_AC_BE; + case 3: + return QOS_AC_BK; + default: + return QOS_AC_BE; + } +} + +void wl1251_tx_work(struct work_struct *work); +void wl1251_tx_complete(struct wl1251 *wl); +void wl1251_tx_flush(struct wl1251 *wl); + +#endif |