diff options
Diffstat (limited to 'drivers/tty/serial/8250/8250_exar.c')
| -rw-r--r-- | drivers/tty/serial/8250/8250_exar.c | 63 |
1 files changed, 46 insertions, 17 deletions
diff --git a/drivers/tty/serial/8250/8250_exar.c b/drivers/tty/serial/8250/8250_exar.c index 8385be8468..23366f868a 100644 --- a/drivers/tty/serial/8250/8250_exar.c +++ b/drivers/tty/serial/8250/8250_exar.c @@ -18,7 +18,6 @@ #include <linux/slab.h> #include <linux/string.h> #include <linux/tty.h> -#include <linux/8250_pci.h> #include <linux/delay.h> #include <asm/byteorder.h> @@ -47,12 +46,6 @@ #define PCI_SUBDEVICE_ID_USR_2980 0x0128 #define PCI_SUBDEVICE_ID_USR_2981 0x0129 -#define PCI_DEVICE_ID_SEALEVEL_710xC 0x1001 -#define PCI_DEVICE_ID_SEALEVEL_720xC 0x1002 -#define PCI_DEVICE_ID_SEALEVEL_740xC 0x1004 -#define PCI_DEVICE_ID_SEALEVEL_780xC 0x1008 -#define PCI_DEVICE_ID_SEALEVEL_716xC 0x1010 - #define UART_EXAR_INT0 0x80 #define UART_EXAR_8XMODE 0x88 /* 8X sampling rate select */ #define UART_EXAR_SLEEP 0x8b /* Sleep mode */ @@ -84,6 +77,9 @@ #define UART_EXAR_RS485_DLY(x) ((x) << 4) +#define UART_EXAR_DLD 0x02 /* Divisor Fractional */ +#define UART_EXAR_DLD_485_POLARITY 0x80 /* RS-485 Enable Signal Polarity */ + /* * IOT2040 MPIO wiring semantics: * @@ -201,9 +197,9 @@ static int xr17v35x_startup(struct uart_port *port) * * Synchronize UART_IER access against the console. */ - spin_lock_irq(&port->lock); + uart_port_lock_irq(port); serial_port_out(port, UART_IER, 0); - spin_unlock_irq(&port->lock); + uart_port_unlock_irq(port); return serial8250_do_startup(port); } @@ -445,6 +441,44 @@ static int generic_rs485_config(struct uart_port *port, struct ktermios *termios return 0; } +static int sealevel_rs485_config(struct uart_port *port, struct ktermios *termios, + struct serial_rs485 *rs485) +{ + u8 __iomem *p = port->membase; + u8 old_lcr; + u8 efr; + u8 dld; + int ret; + + ret = generic_rs485_config(port, termios, rs485); + if (ret) + return ret; + + if (rs485->flags & SER_RS485_ENABLED) { + old_lcr = readb(p + UART_LCR); + + /* Set EFR[4]=1 to enable enhanced feature registers */ + efr = readb(p + UART_XR_EFR); + efr |= UART_EFR_ECB; + writeb(efr, p + UART_XR_EFR); + + /* Set MCR to use DTR as Auto-RS485 Enable signal */ + writeb(UART_MCR_OUT1, p + UART_MCR); + + /* Set LCR[7]=1 to enable access to DLD register */ + writeb(old_lcr | UART_LCR_DLAB, p + UART_LCR); + + /* Set DLD[7]=1 for inverted RS485 Enable logic */ + dld = readb(p + UART_EXAR_DLD); + dld |= UART_EXAR_DLD_485_POLARITY; + writeb(dld, p + UART_EXAR_DLD); + + writeb(old_lcr, p + UART_LCR); + } + + return 0; +} + static const struct serial_rs485 generic_rs485_supported = { .flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND, }; @@ -567,6 +601,9 @@ pci_xr17v35x_setup(struct exar8250 *priv, struct pci_dev *pcidev, port->port.rs485_config = platform->rs485_config; port->port.rs485_supported = *(platform->rs485_supported); + if (pcidev->subsystem_vendor == PCI_VENDOR_ID_SEALEVEL) + port->port.rs485_config = sealevel_rs485_config; + /* * Setup the UART clock for the devices on expansion slot to * half the clock speed of the main chip (which is 125MHz) @@ -653,8 +690,6 @@ exar_pci_probe(struct pci_dev *pcidev, const struct pci_device_id *ent) nr_ports = BIT(((pcidev->device & 0x38) >> 3) - 1); else if (board->num_ports) nr_ports = board->num_ports; - else if (pcidev->vendor == PCI_VENDOR_ID_SEALEVEL) - nr_ports = pcidev->device & 0xff; else nr_ports = pcidev->device & 0x0f; @@ -894,12 +929,6 @@ static const struct pci_device_id exar_pci_tbl[] = { EXAR_DEVICE(COMMTECH, 4224PCI335, pbn_fastcom335_4), EXAR_DEVICE(COMMTECH, 2324PCI335, pbn_fastcom335_4), EXAR_DEVICE(COMMTECH, 2328PCI335, pbn_fastcom335_8), - - EXAR_DEVICE(SEALEVEL, 710xC, pbn_exar_XR17V35x), - EXAR_DEVICE(SEALEVEL, 720xC, pbn_exar_XR17V35x), - EXAR_DEVICE(SEALEVEL, 740xC, pbn_exar_XR17V35x), - EXAR_DEVICE(SEALEVEL, 780xC, pbn_exar_XR17V35x), - EXAR_DEVICE(SEALEVEL, 716xC, pbn_exar_XR17V35x), { 0, } }; MODULE_DEVICE_TABLE(pci, exar_pci_tbl); |