diff options
Diffstat (limited to 'mm/Kconfig')
| -rw-r--r-- | mm/Kconfig | 1263 |
1 files changed, 1263 insertions, 0 deletions
diff --git a/mm/Kconfig b/mm/Kconfig new file mode 100644 index 000000000..264a2df5e --- /dev/null +++ b/mm/Kconfig @@ -0,0 +1,1263 @@ +# SPDX-License-Identifier: GPL-2.0-only + +menu "Memory Management options" + +# +# For some reason microblaze and nios2 hard code SWAP=n. Hopefully we can +# add proper SWAP support to them, in which case this can be remove. +# +config ARCH_NO_SWAP + bool + +config ZPOOL + bool + +menuconfig SWAP + bool "Support for paging of anonymous memory (swap)" + depends on MMU && BLOCK && !ARCH_NO_SWAP + default y + help + This option allows you to choose whether you want to have support + for so called swap devices or swap files in your kernel that are + used to provide more virtual memory than the actual RAM present + in your computer. If unsure say Y. + +config ZSWAP + bool "Compressed cache for swap pages" + depends on SWAP + select CRYPTO + select ZPOOL + help + A lightweight compressed cache for swap pages. It takes + pages that are in the process of being swapped out and attempts to + compress them into a dynamically allocated RAM-based memory pool. + This can result in a significant I/O reduction on swap device and, + in the case where decompressing from RAM is faster than swap device + reads, can also improve workload performance. + +config ZSWAP_DEFAULT_ON + bool "Enable the compressed cache for swap pages by default" + depends on ZSWAP + help + If selected, the compressed cache for swap pages will be enabled + at boot, otherwise it will be disabled. + + The selection made here can be overridden by using the kernel + command line 'zswap.enabled=' option. + +config ZSWAP_EXCLUSIVE_LOADS_DEFAULT_ON + bool "Invalidate zswap entries when pages are loaded" + depends on ZSWAP + help + If selected, exclusive loads for zswap will be enabled at boot, + otherwise it will be disabled. + + If exclusive loads are enabled, when a page is loaded from zswap, + the zswap entry is invalidated at once, as opposed to leaving it + in zswap until the swap entry is freed. + + This avoids having two copies of the same page in memory + (compressed and uncompressed) after faulting in a page from zswap. + The cost is that if the page was never dirtied and needs to be + swapped out again, it will be re-compressed. + +choice + prompt "Default compressor" + depends on ZSWAP + default ZSWAP_COMPRESSOR_DEFAULT_LZO + help + Selects the default compression algorithm for the compressed cache + for swap pages. + + For an overview what kind of performance can be expected from + a particular compression algorithm please refer to the benchmarks + available at the following LWN page: + https://lwn.net/Articles/751795/ + + If in doubt, select 'LZO'. + + The selection made here can be overridden by using the kernel + command line 'zswap.compressor=' option. + +config ZSWAP_COMPRESSOR_DEFAULT_DEFLATE + bool "Deflate" + select CRYPTO_DEFLATE + help + Use the Deflate algorithm as the default compression algorithm. + +config ZSWAP_COMPRESSOR_DEFAULT_LZO + bool "LZO" + select CRYPTO_LZO + help + Use the LZO algorithm as the default compression algorithm. + +config ZSWAP_COMPRESSOR_DEFAULT_842 + bool "842" + select CRYPTO_842 + help + Use the 842 algorithm as the default compression algorithm. + +config ZSWAP_COMPRESSOR_DEFAULT_LZ4 + bool "LZ4" + select CRYPTO_LZ4 + help + Use the LZ4 algorithm as the default compression algorithm. + +config ZSWAP_COMPRESSOR_DEFAULT_LZ4HC + bool "LZ4HC" + select CRYPTO_LZ4HC + help + Use the LZ4HC algorithm as the default compression algorithm. + +config ZSWAP_COMPRESSOR_DEFAULT_ZSTD + bool "zstd" + select CRYPTO_ZSTD + help + Use the zstd algorithm as the default compression algorithm. +endchoice + +config ZSWAP_COMPRESSOR_DEFAULT + string + depends on ZSWAP + default "deflate" if ZSWAP_COMPRESSOR_DEFAULT_DEFLATE + default "lzo" if ZSWAP_COMPRESSOR_DEFAULT_LZO + default "842" if ZSWAP_COMPRESSOR_DEFAULT_842 + default "lz4" if ZSWAP_COMPRESSOR_DEFAULT_LZ4 + default "lz4hc" if ZSWAP_COMPRESSOR_DEFAULT_LZ4HC + default "zstd" if ZSWAP_COMPRESSOR_DEFAULT_ZSTD + default "" + +choice + prompt "Default allocator" + depends on ZSWAP + default ZSWAP_ZPOOL_DEFAULT_ZBUD + help + Selects the default allocator for the compressed cache for + swap pages. + The default is 'zbud' for compatibility, however please do + read the description of each of the allocators below before + making a right choice. + + The selection made here can be overridden by using the kernel + command line 'zswap.zpool=' option. + +config ZSWAP_ZPOOL_DEFAULT_ZBUD + bool "zbud" + select ZBUD + help + Use the zbud allocator as the default allocator. + +config ZSWAP_ZPOOL_DEFAULT_Z3FOLD + bool "z3fold" + select Z3FOLD + help + Use the z3fold allocator as the default allocator. + +config ZSWAP_ZPOOL_DEFAULT_ZSMALLOC + bool "zsmalloc" + select ZSMALLOC + help + Use the zsmalloc allocator as the default allocator. +endchoice + +config ZSWAP_ZPOOL_DEFAULT + string + depends on ZSWAP + default "zbud" if ZSWAP_ZPOOL_DEFAULT_ZBUD + default "z3fold" if ZSWAP_ZPOOL_DEFAULT_Z3FOLD + default "zsmalloc" if ZSWAP_ZPOOL_DEFAULT_ZSMALLOC + default "" + +config ZBUD + tristate "2:1 compression allocator (zbud)" + depends on ZSWAP + help + A special purpose allocator for storing compressed pages. + It is designed to store up to two compressed pages per physical + page. While this design limits storage density, it has simple and + deterministic reclaim properties that make it preferable to a higher + density approach when reclaim will be used. + +config Z3FOLD + tristate "3:1 compression allocator (z3fold)" + depends on ZSWAP + help + A special purpose allocator for storing compressed pages. + It is designed to store up to three compressed pages per physical + page. It is a ZBUD derivative so the simplicity and determinism are + still there. + +config ZSMALLOC + tristate + prompt "N:1 compression allocator (zsmalloc)" if ZSWAP + depends on MMU + help + zsmalloc is a slab-based memory allocator designed to store + pages of various compression levels efficiently. It achieves + the highest storage density with the least amount of fragmentation. + +config ZSMALLOC_STAT + bool "Export zsmalloc statistics" + depends on ZSMALLOC + select DEBUG_FS + help + This option enables code in the zsmalloc to collect various + statistics about what's happening in zsmalloc and exports that + information to userspace via debugfs. + If unsure, say N. + +config ZSMALLOC_CHAIN_SIZE + int "Maximum number of physical pages per-zspage" + default 8 + range 4 16 + depends on ZSMALLOC + help + This option sets the upper limit on the number of physical pages + that a zmalloc page (zspage) can consist of. The optimal zspage + chain size is calculated for each size class during the + initialization of the pool. + + Changing this option can alter the characteristics of size classes, + such as the number of pages per zspage and the number of objects + per zspage. This can also result in different configurations of + the pool, as zsmalloc merges size classes with similar + characteristics. + + For more information, see zsmalloc documentation. + +menu "SLAB allocator options" + +choice + prompt "Choose SLAB allocator" + default SLUB + help + This option allows to select a slab allocator. + +config SLAB_DEPRECATED + bool "SLAB (DEPRECATED)" + depends on !PREEMPT_RT + help + Deprecated and scheduled for removal in a few cycles. Replaced by + SLUB. + + If you cannot migrate to SLUB, please contact linux-mm@kvack.org + and the people listed in the SLAB ALLOCATOR section of MAINTAINERS + file, explaining why. + + The regular slab allocator that is established and known to work + well in all environments. It organizes cache hot objects in + per cpu and per node queues. + +config SLUB + bool "SLUB (Unqueued Allocator)" + help + SLUB is a slab allocator that minimizes cache line usage + instead of managing queues of cached objects (SLAB approach). + Per cpu caching is realized using slabs of objects instead + of queues of objects. SLUB can use memory efficiently + and has enhanced diagnostics. SLUB is the default choice for + a slab allocator. + +endchoice + +config SLAB + bool + default y + depends on SLAB_DEPRECATED + +config SLUB_TINY + bool "Configure SLUB for minimal memory footprint" + depends on SLUB && EXPERT + select SLAB_MERGE_DEFAULT + help + Configures the SLUB allocator in a way to achieve minimal memory + footprint, sacrificing scalability, debugging and other features. + This is intended only for the smallest system that had used the + SLOB allocator and is not recommended for systems with more than + 16MB RAM. + + If unsure, say N. + +config SLAB_MERGE_DEFAULT + bool "Allow slab caches to be merged" + default y + depends on SLAB || SLUB + help + For reduced kernel memory fragmentation, slab caches can be + merged when they share the same size and other characteristics. + This carries a risk of kernel heap overflows being able to + overwrite objects from merged caches (and more easily control + cache layout), which makes such heap attacks easier to exploit + by attackers. By keeping caches unmerged, these kinds of exploits + can usually only damage objects in the same cache. To disable + merging at runtime, "slab_nomerge" can be passed on the kernel + command line. + +config SLAB_FREELIST_RANDOM + bool "Randomize slab freelist" + depends on SLAB || (SLUB && !SLUB_TINY) + help + Randomizes the freelist order used on creating new pages. This + security feature reduces the predictability of the kernel slab + allocator against heap overflows. + +config SLAB_FREELIST_HARDENED + bool "Harden slab freelist metadata" + depends on SLAB || (SLUB && !SLUB_TINY) + help + Many kernel heap attacks try to target slab cache metadata and + other infrastructure. This options makes minor performance + sacrifices to harden the kernel slab allocator against common + freelist exploit methods. Some slab implementations have more + sanity-checking than others. This option is most effective with + CONFIG_SLUB. + +config SLUB_STATS + default n + bool "Enable SLUB performance statistics" + depends on SLUB && SYSFS && !SLUB_TINY + help + SLUB statistics are useful to debug SLUBs allocation behavior in + order find ways to optimize the allocator. This should never be + enabled for production use since keeping statistics slows down + the allocator by a few percentage points. The slabinfo command + supports the determination of the most active slabs to figure + out which slabs are relevant to a particular load. + Try running: slabinfo -DA + +config SLUB_CPU_PARTIAL + default y + depends on SLUB && SMP && !SLUB_TINY + bool "SLUB per cpu partial cache" + help + Per cpu partial caches accelerate objects allocation and freeing + that is local to a processor at the price of more indeterminism + in the latency of the free. On overflow these caches will be cleared + which requires the taking of locks that may cause latency spikes. + Typically one would choose no for a realtime system. + +config RANDOM_KMALLOC_CACHES + default n + depends on SLUB && !SLUB_TINY + bool "Randomize slab caches for normal kmalloc" + help + A hardening feature that creates multiple copies of slab caches for + normal kmalloc allocation and makes kmalloc randomly pick one based + on code address, which makes the attackers more difficult to spray + vulnerable memory objects on the heap for the purpose of exploiting + memory vulnerabilities. + + Currently the number of copies is set to 16, a reasonably large value + that effectively diverges the memory objects allocated for different + subsystems or modules into different caches, at the expense of a + limited degree of memory and CPU overhead that relates to hardware and + system workload. + +endmenu # SLAB allocator options + +config SHUFFLE_PAGE_ALLOCATOR + bool "Page allocator randomization" + default SLAB_FREELIST_RANDOM && ACPI_NUMA + help + Randomization of the page allocator improves the average + utilization of a direct-mapped memory-side-cache. See section + 5.2.27 Heterogeneous Memory Attribute Table (HMAT) in the ACPI + 6.2a specification for an example of how a platform advertises + the presence of a memory-side-cache. There are also incidental + security benefits as it reduces the predictability of page + allocations to compliment SLAB_FREELIST_RANDOM, but the + default granularity of shuffling on the MAX_ORDER i.e, 10th + order of pages is selected based on cache utilization benefits + on x86. + + While the randomization improves cache utilization it may + negatively impact workloads on platforms without a cache. For + this reason, by default, the randomization is enabled only + after runtime detection of a direct-mapped memory-side-cache. + Otherwise, the randomization may be force enabled with the + 'page_alloc.shuffle' kernel command line parameter. + + Say Y if unsure. + +config COMPAT_BRK + bool "Disable heap randomization" + default y + help + Randomizing heap placement makes heap exploits harder, but it + also breaks ancient binaries (including anything libc5 based). + This option changes the bootup default to heap randomization + disabled, and can be overridden at runtime by setting + /proc/sys/kernel/randomize_va_space to 2. + + On non-ancient distros (post-2000 ones) N is usually a safe choice. + +config MMAP_ALLOW_UNINITIALIZED + bool "Allow mmapped anonymous memory to be uninitialized" + depends on EXPERT && !MMU + default n + help + Normally, and according to the Linux spec, anonymous memory obtained + from mmap() has its contents cleared before it is passed to + userspace. Enabling this config option allows you to request that + mmap() skip that if it is given an MAP_UNINITIALIZED flag, thus + providing a huge performance boost. If this option is not enabled, + then the flag will be ignored. + + This is taken advantage of by uClibc's malloc(), and also by + ELF-FDPIC binfmt's brk and stack allocator. + + Because of the obvious security issues, this option should only be + enabled on embedded devices where you control what is run in + userspace. Since that isn't generally a problem on no-MMU systems, + it is normally safe to say Y here. + + See Documentation/admin-guide/mm/nommu-mmap.rst for more information. + +config SELECT_MEMORY_MODEL + def_bool y + depends on ARCH_SELECT_MEMORY_MODEL + +choice + prompt "Memory model" + depends on SELECT_MEMORY_MODEL + default SPARSEMEM_MANUAL if ARCH_SPARSEMEM_DEFAULT + default FLATMEM_MANUAL + help + This option allows you to change some of the ways that + Linux manages its memory internally. Most users will + only have one option here selected by the architecture + configuration. This is normal. + +config FLATMEM_MANUAL + bool "Flat Memory" + depends on !ARCH_SPARSEMEM_ENABLE || ARCH_FLATMEM_ENABLE + help + This option is best suited for non-NUMA systems with + flat address space. The FLATMEM is the most efficient + system in terms of performance and resource consumption + and it is the best option for smaller systems. + + For systems that have holes in their physical address + spaces and for features like NUMA and memory hotplug, + choose "Sparse Memory". + + If unsure, choose this option (Flat Memory) over any other. + +config SPARSEMEM_MANUAL + bool "Sparse Memory" + depends on ARCH_SPARSEMEM_ENABLE + help + This will be the only option for some systems, including + memory hot-plug systems. This is normal. + + This option provides efficient support for systems with + holes is their physical address space and allows memory + hot-plug and hot-remove. + + If unsure, choose "Flat Memory" over this option. + +endchoice + +config SPARSEMEM + def_bool y + depends on (!SELECT_MEMORY_MODEL && ARCH_SPARSEMEM_ENABLE) || SPARSEMEM_MANUAL + +config FLATMEM + def_bool y + depends on !SPARSEMEM || FLATMEM_MANUAL + +# +# SPARSEMEM_EXTREME (which is the default) does some bootmem +# allocations when sparse_init() is called. If this cannot +# be done on your architecture, select this option. However, +# statically allocating the mem_section[] array can potentially +# consume vast quantities of .bss, so be careful. +# +# This option will also potentially produce smaller runtime code +# with gcc 3.4 and later. +# +config SPARSEMEM_STATIC + bool + +# +# Architecture platforms which require a two level mem_section in SPARSEMEM +# must select this option. This is usually for architecture platforms with +# an extremely sparse physical address space. +# +config SPARSEMEM_EXTREME + def_bool y + depends on SPARSEMEM && !SPARSEMEM_STATIC + +config SPARSEMEM_VMEMMAP_ENABLE + bool + +config SPARSEMEM_VMEMMAP + bool "Sparse Memory virtual memmap" + depends on SPARSEMEM && SPARSEMEM_VMEMMAP_ENABLE + default y + help + SPARSEMEM_VMEMMAP uses a virtually mapped memmap to optimise + pfn_to_page and page_to_pfn operations. This is the most + efficient option when sufficient kernel resources are available. +# +# Select this config option from the architecture Kconfig, if it is preferred +# to enable the feature of HugeTLB/dev_dax vmemmap optimization. +# +config ARCH_WANT_OPTIMIZE_DAX_VMEMMAP + bool + +config ARCH_WANT_OPTIMIZE_HUGETLB_VMEMMAP + bool + +config HAVE_MEMBLOCK_PHYS_MAP + bool + +config HAVE_FAST_GUP + depends on MMU + bool + +# Don't discard allocated memory used to track "memory" and "reserved" memblocks +# after early boot, so it can still be used to test for validity of memory. +# Also, memblocks are updated with memory hot(un)plug. +config ARCH_KEEP_MEMBLOCK + bool + +# Keep arch NUMA mapping infrastructure post-init. +config NUMA_KEEP_MEMINFO + bool + +config MEMORY_ISOLATION + bool + +# IORESOURCE_SYSTEM_RAM regions in the kernel resource tree that are marked +# IORESOURCE_EXCLUSIVE cannot be mapped to user space, for example, via +# /dev/mem. +config EXCLUSIVE_SYSTEM_RAM + def_bool y + depends on !DEVMEM || STRICT_DEVMEM + +# +# Only be set on architectures that have completely implemented memory hotplug +# feature. If you are not sure, don't touch it. +# +config HAVE_BOOTMEM_INFO_NODE + def_bool n + +config ARCH_ENABLE_MEMORY_HOTPLUG + bool + +config ARCH_ENABLE_MEMORY_HOTREMOVE + bool + +# eventually, we can have this option just 'select SPARSEMEM' +menuconfig MEMORY_HOTPLUG + bool "Memory hotplug" + select MEMORY_ISOLATION + depends on SPARSEMEM + depends on ARCH_ENABLE_MEMORY_HOTPLUG + depends on 64BIT + select NUMA_KEEP_MEMINFO if NUMA + +if MEMORY_HOTPLUG + +config MEMORY_HOTPLUG_DEFAULT_ONLINE + bool "Online the newly added memory blocks by default" + depends on MEMORY_HOTPLUG + help + This option sets the default policy setting for memory hotplug + onlining policy (/sys/devices/system/memory/auto_online_blocks) which + determines what happens to newly added memory regions. Policy setting + can always be changed at runtime. + See Documentation/admin-guide/mm/memory-hotplug.rst for more information. + + Say Y here if you want all hot-plugged memory blocks to appear in + 'online' state by default. + Say N here if you want the default policy to keep all hot-plugged + memory blocks in 'offline' state. + +config MEMORY_HOTREMOVE + bool "Allow for memory hot remove" + select HAVE_BOOTMEM_INFO_NODE if (X86_64 || PPC64) + depends on MEMORY_HOTPLUG && ARCH_ENABLE_MEMORY_HOTREMOVE + depends on MIGRATION + +config MHP_MEMMAP_ON_MEMORY + def_bool y + depends on MEMORY_HOTPLUG && SPARSEMEM_VMEMMAP + depends on ARCH_MHP_MEMMAP_ON_MEMORY_ENABLE + +endif # MEMORY_HOTPLUG + +config ARCH_MHP_MEMMAP_ON_MEMORY_ENABLE + bool + +# Heavily threaded applications may benefit from splitting the mm-wide +# page_table_lock, so that faults on different parts of the user address +# space can be handled with less contention: split it at this NR_CPUS. +# Default to 4 for wider testing, though 8 might be more appropriate. +# ARM's adjust_pte (unused if VIPT) depends on mm-wide page_table_lock. +# PA-RISC 7xxx's spinlock_t would enlarge struct page from 32 to 44 bytes. +# SPARC32 allocates multiple pte tables within a single page, and therefore +# a per-page lock leads to problems when multiple tables need to be locked +# at the same time (e.g. copy_page_range()). +# DEBUG_SPINLOCK and DEBUG_LOCK_ALLOC spinlock_t also enlarge struct page. +# +config SPLIT_PTLOCK_CPUS + int + default "999999" if !MMU + default "999999" if ARM && !CPU_CACHE_VIPT + default "999999" if PARISC && !PA20 + default "999999" if SPARC32 + default "4" + +config ARCH_ENABLE_SPLIT_PMD_PTLOCK + bool + +# +# support for memory balloon +config MEMORY_BALLOON + bool + +# +# support for memory balloon compaction +config BALLOON_COMPACTION + bool "Allow for balloon memory compaction/migration" + def_bool y + depends on COMPACTION && MEMORY_BALLOON + help + Memory fragmentation introduced by ballooning might reduce + significantly the number of 2MB contiguous memory blocks that can be + used within a guest, thus imposing performance penalties associated + with the reduced number of transparent huge pages that could be used + by the guest workload. Allowing the compaction & migration for memory + pages enlisted as being part of memory balloon devices avoids the + scenario aforementioned and helps improving memory defragmentation. + +# +# support for memory compaction +config COMPACTION + bool "Allow for memory compaction" + def_bool y + select MIGRATION + depends on MMU + help + Compaction is the only memory management component to form + high order (larger physically contiguous) memory blocks + reliably. The page allocator relies on compaction heavily and + the lack of the feature can lead to unexpected OOM killer + invocations for high order memory requests. You shouldn't + disable this option unless there really is a strong reason for + it and then we would be really interested to hear about that at + linux-mm@kvack.org. + +config COMPACT_UNEVICTABLE_DEFAULT + int + depends on COMPACTION + default 0 if PREEMPT_RT + default 1 + +# +# support for free page reporting +config PAGE_REPORTING + bool "Free page reporting" + def_bool n + help + Free page reporting allows for the incremental acquisition of + free pages from the buddy allocator for the purpose of reporting + those pages to another entity, such as a hypervisor, so that the + memory can be freed within the host for other uses. + +# +# support for page migration +# +config MIGRATION + bool "Page migration" + def_bool y + depends on (NUMA || ARCH_ENABLE_MEMORY_HOTREMOVE || COMPACTION || CMA) && MMU + help + Allows the migration of the physical location of pages of processes + while the virtual addresses are not changed. This is useful in + two situations. The first is on NUMA systems to put pages nearer + to the processors accessing. The second is when allocating huge + pages as migration can relocate pages to satisfy a huge page + allocation instead of reclaiming. + +config DEVICE_MIGRATION + def_bool MIGRATION && ZONE_DEVICE + +config ARCH_ENABLE_HUGEPAGE_MIGRATION + bool + +config ARCH_ENABLE_THP_MIGRATION + bool + +config HUGETLB_PAGE_SIZE_VARIABLE + def_bool n + help + Allows the pageblock_order value to be dynamic instead of just standard + HUGETLB_PAGE_ORDER when there are multiple HugeTLB page sizes available + on a platform. + + Note that the pageblock_order cannot exceed MAX_ORDER and will be + clamped down to MAX_ORDER. + +config CONTIG_ALLOC + def_bool (MEMORY_ISOLATION && COMPACTION) || CMA + +config PHYS_ADDR_T_64BIT + def_bool 64BIT + +config BOUNCE + bool "Enable bounce buffers" + default y + depends on BLOCK && MMU && HIGHMEM + help + Enable bounce buffers for devices that cannot access the full range of + memory available to the CPU. Enabled by default when HIGHMEM is + selected, but you may say n to override this. + +config MMU_NOTIFIER + bool + select INTERVAL_TREE + +config KSM + bool "Enable KSM for page merging" + depends on MMU + select XXHASH + help + Enable Kernel Samepage Merging: KSM periodically scans those areas + of an application's address space that an app has advised may be + mergeable. When it finds pages of identical content, it replaces + the many instances by a single page with that content, so + saving memory until one or another app needs to modify the content. + Recommended for use with KVM, or with other duplicative applications. + See Documentation/mm/ksm.rst for more information: KSM is inactive + until a program has madvised that an area is MADV_MERGEABLE, and + root has set /sys/kernel/mm/ksm/run to 1 (if CONFIG_SYSFS is set). + +config DEFAULT_MMAP_MIN_ADDR + int "Low address space to protect from user allocation" + depends on MMU + default 4096 + help + This is the portion of low virtual memory which should be protected + from userspace allocation. Keeping a user from writing to low pages + can help reduce the impact of kernel NULL pointer bugs. + + For most ia64, ppc64 and x86 users with lots of address space + a value of 65536 is reasonable and should cause no problems. + On arm and other archs it should not be higher than 32768. + Programs which use vm86 functionality or have some need to map + this low address space will need CAP_SYS_RAWIO or disable this + protection by setting the value to 0. + + This value can be changed after boot using the + /proc/sys/vm/mmap_min_addr tunable. + +config ARCH_SUPPORTS_MEMORY_FAILURE + bool + +config MEMORY_FAILURE + depends on MMU + depends on ARCH_SUPPORTS_MEMORY_FAILURE + bool "Enable recovery from hardware memory errors" + select MEMORY_ISOLATION + select RAS + help + Enables code to recover from some memory failures on systems + with MCA recovery. This allows a system to continue running + even when some of its memory has uncorrected errors. This requires + special hardware support and typically ECC memory. + +config HWPOISON_INJECT + tristate "HWPoison pages injector" + depends on MEMORY_FAILURE && DEBUG_KERNEL && PROC_FS + select PROC_PAGE_MONITOR + +config NOMMU_INITIAL_TRIM_EXCESS + int "Turn on mmap() excess space trimming before booting" + depends on !MMU + default 1 + help + The NOMMU mmap() frequently needs to allocate large contiguous chunks + of memory on which to store mappings, but it can only ask the system + allocator for chunks in 2^N*PAGE_SIZE amounts - which is frequently + more than it requires. To deal with this, mmap() is able to trim off + the excess and return it to the allocator. + + If trimming is enabled, the excess is trimmed off and returned to the + system allocator, which can cause extra fragmentation, particularly + if there are a lot of transient processes. + + If trimming is disabled, the excess is kept, but not used, which for + long-term mappings means that the space is wasted. + + Trimming can be dynamically controlled through a sysctl option + (/proc/sys/vm/nr_trim_pages) which specifies the minimum number of + excess pages there must be before trimming should occur, or zero if + no trimming is to occur. + + This option specifies the initial value of this option. The default + of 1 says that all excess pages should be trimmed. + + See Documentation/admin-guide/mm/nommu-mmap.rst for more information. + +config ARCH_WANT_GENERAL_HUGETLB + bool + +config ARCH_WANTS_THP_SWAP + def_bool n + +menuconfig TRANSPARENT_HUGEPAGE + bool "Transparent Hugepage Support" + depends on HAVE_ARCH_TRANSPARENT_HUGEPAGE && !PREEMPT_RT + select COMPACTION + select XARRAY_MULTI + help + Transparent Hugepages allows the kernel to use huge pages and + huge tlb transparently to the applications whenever possible. + This feature can improve computing performance to certain + applications by speeding up page faults during memory + allocation, by reducing the number of tlb misses and by speeding + up the pagetable walking. + + If memory constrained on embedded, you may want to say N. + +if TRANSPARENT_HUGEPAGE + +choice + prompt "Transparent Hugepage Support sysfs defaults" + depends on TRANSPARENT_HUGEPAGE + default TRANSPARENT_HUGEPAGE_ALWAYS + help + Selects the sysfs defaults for Transparent Hugepage Support. + + config TRANSPARENT_HUGEPAGE_ALWAYS + bool "always" + help + Enabling Transparent Hugepage always, can increase the + memory footprint of applications without a guaranteed + benefit but it will work automatically for all applications. + + config TRANSPARENT_HUGEPAGE_MADVISE + bool "madvise" + help + Enabling Transparent Hugepage madvise, will only provide a + performance improvement benefit to the applications using + madvise(MADV_HUGEPAGE) but it won't risk to increase the + memory footprint of applications without a guaranteed + benefit. +endchoice + +config THP_SWAP + def_bool y + depends on TRANSPARENT_HUGEPAGE && ARCH_WANTS_THP_SWAP && SWAP && 64BIT + help + Swap transparent huge pages in one piece, without splitting. + XXX: For now, swap cluster backing transparent huge page + will be split after swapout. + + For selection by architectures with reasonable THP sizes. + +config READ_ONLY_THP_FOR_FS + bool "Read-only THP for filesystems (EXPERIMENTAL)" + depends on TRANSPARENT_HUGEPAGE && SHMEM + + help + Allow khugepaged to put read-only file-backed pages in THP. + + This is marked experimental because it is a new feature. Write + support of file THPs will be developed in the next few release + cycles. + +endif # TRANSPARENT_HUGEPAGE + +# +# UP and nommu archs use km based percpu allocator +# +config NEED_PER_CPU_KM + depends on !SMP || !MMU + bool + default y + +config NEED_PER_CPU_EMBED_FIRST_CHUNK + bool + +config NEED_PER_CPU_PAGE_FIRST_CHUNK + bool + +config USE_PERCPU_NUMA_NODE_ID + bool + +config HAVE_SETUP_PER_CPU_AREA + bool + +config CMA + bool "Contiguous Memory Allocator" + depends on MMU + select MIGRATION + select MEMORY_ISOLATION + help + This enables the Contiguous Memory Allocator which allows other + subsystems to allocate big physically-contiguous blocks of memory. + CMA reserves a region of memory and allows only movable pages to + be allocated from it. This way, the kernel can use the memory for + pagecache and when a subsystem requests for contiguous area, the + allocated pages are migrated away to serve the contiguous request. + + If unsure, say "n". + +config CMA_DEBUG + bool "CMA debug messages (DEVELOPMENT)" + depends on DEBUG_KERNEL && CMA + help + Turns on debug messages in CMA. This produces KERN_DEBUG + messages for every CMA call as well as various messages while + processing calls such as dma_alloc_from_contiguous(). + This option does not affect warning and error messages. + +config CMA_DEBUGFS + bool "CMA debugfs interface" + depends on CMA && DEBUG_FS + help + Turns on the DebugFS interface for CMA. + +config CMA_SYSFS + bool "CMA information through sysfs interface" + depends on CMA && SYSFS + help + This option exposes some sysfs attributes to get information + from CMA. + +config CMA_AREAS + int "Maximum count of the CMA areas" + depends on CMA + default 19 if NUMA + default 7 + help + CMA allows to create CMA areas for particular purpose, mainly, + used as device private area. This parameter sets the maximum + number of CMA area in the system. + + If unsure, leave the default value "7" in UMA and "19" in NUMA. + +config MEM_SOFT_DIRTY + bool "Track memory changes" + depends on CHECKPOINT_RESTORE && HAVE_ARCH_SOFT_DIRTY && PROC_FS + select PROC_PAGE_MONITOR + help + This option enables memory changes tracking by introducing a + soft-dirty bit on pte-s. This bit it set when someone writes + into a page just as regular dirty bit, but unlike the latter + it can be cleared by hands. + + See Documentation/admin-guide/mm/soft-dirty.rst for more details. + +config GENERIC_EARLY_IOREMAP + bool + +config STACK_MAX_DEFAULT_SIZE_MB + int "Default maximum user stack size for 32-bit processes (MB)" + default 100 + range 8 2048 + depends on STACK_GROWSUP && (!64BIT || COMPAT) + help + This is the maximum stack size in Megabytes in the VM layout of 32-bit + user processes when the stack grows upwards (currently only on parisc + arch) when the RLIMIT_STACK hard limit is unlimited. + + A sane initial value is 100 MB. + +config DEFERRED_STRUCT_PAGE_INIT + bool "Defer initialisation of struct pages to kthreads" + depends on SPARSEMEM + depends on !NEED_PER_CPU_KM + depends on 64BIT + select PADATA + help + Ordinarily all struct pages are initialised during early boot in a + single thread. On very large machines this can take a considerable + amount of time. If this option is set, large machines will bring up + a subset of memmap at boot and then initialise the rest in parallel. + This has a potential performance impact on tasks running early in the + lifetime of the system until these kthreads finish the + initialisation. + +config PAGE_IDLE_FLAG + bool + select PAGE_EXTENSION if !64BIT + help + This adds PG_idle and PG_young flags to 'struct page'. PTE Accessed + bit writers can set the state of the bit in the flags so that PTE + Accessed bit readers may avoid disturbance. + +config IDLE_PAGE_TRACKING + bool "Enable idle page tracking" + depends on SYSFS && MMU + select PAGE_IDLE_FLAG + help + This feature allows to estimate the amount of user pages that have + not been touched during a given period of time. This information can + be useful to tune memory cgroup limits and/or for job placement + within a compute cluster. + + See Documentation/admin-guide/mm/idle_page_tracking.rst for + more details. + +config ARCH_HAS_CACHE_LINE_SIZE + bool + +config ARCH_HAS_CURRENT_STACK_POINTER + bool + help + In support of HARDENED_USERCOPY performing stack variable lifetime + checking, an architecture-agnostic way to find the stack pointer + is needed. Once an architecture defines an unsigned long global + register alias named "current_stack_pointer", this config can be + selected. + +config ARCH_HAS_PTE_DEVMAP + bool + +config ARCH_HAS_ZONE_DMA_SET + bool + +config ZONE_DMA + bool "Support DMA zone" if ARCH_HAS_ZONE_DMA_SET + default y if ARM64 || X86 + +config ZONE_DMA32 + bool "Support DMA32 zone" if ARCH_HAS_ZONE_DMA_SET + depends on !X86_32 + default y if ARM64 + +config ZONE_DEVICE + bool "Device memory (pmem, HMM, etc...) hotplug support" + depends on MEMORY_HOTPLUG + depends on MEMORY_HOTREMOVE + depends on SPARSEMEM_VMEMMAP + depends on ARCH_HAS_PTE_DEVMAP + select XARRAY_MULTI + + help + Device memory hotplug support allows for establishing pmem, + or other device driver discovered memory regions, in the + memmap. This allows pfn_to_page() lookups of otherwise + "device-physical" addresses which is needed for using a DAX + mapping in an O_DIRECT operation, among other things. + + If FS_DAX is enabled, then say Y. + +# +# Helpers to mirror range of the CPU page tables of a process into device page +# tables. +# +config HMM_MIRROR + bool + depends on MMU + +config GET_FREE_REGION + depends on SPARSEMEM + bool + +config DEVICE_PRIVATE + bool "Unaddressable device memory (GPU memory, ...)" + depends on ZONE_DEVICE + select GET_FREE_REGION + + help + Allows creation of struct pages to represent unaddressable device + memory; i.e., memory that is only accessible from the device (or + group of devices). You likely also want to select HMM_MIRROR. + +config VMAP_PFN + bool + +config ARCH_USES_HIGH_VMA_FLAGS + bool +config ARCH_HAS_PKEYS + bool + +config ARCH_USES_PG_ARCH_X + bool + help + Enable the definition of PG_arch_x page flags with x > 1. Only + suitable for 64-bit architectures with CONFIG_FLATMEM or + CONFIG_SPARSEMEM_VMEMMAP enabled, otherwise there may not be + enough room for additional bits in page->flags. + +config VM_EVENT_COUNTERS + default y + bool "Enable VM event counters for /proc/vmstat" if EXPERT + help + VM event counters are needed for event counts to be shown. + This option allows the disabling of the VM event counters + on EXPERT systems. /proc/vmstat will only show page counts + if VM event counters are disabled. + +config PERCPU_STATS + bool "Collect percpu memory statistics" + help + This feature collects and exposes statistics via debugfs. The + information includes global and per chunk statistics, which can + be used to help understand percpu memory usage. + +config GUP_TEST + bool "Enable infrastructure for get_user_pages()-related unit tests" + depends on DEBUG_FS + help + Provides /sys/kernel/debug/gup_test, which in turn provides a way + to make ioctl calls that can launch kernel-based unit tests for + the get_user_pages*() and pin_user_pages*() family of API calls. + + These tests include benchmark testing of the _fast variants of + get_user_pages*() and pin_user_pages*(), as well as smoke tests of + the non-_fast variants. + + There is also a sub-test that allows running dump_page() on any + of up to eight pages (selected by command line args) within the + range of user-space addresses. These pages are either pinned via + pin_user_pages*(), or pinned via get_user_pages*(), as specified + by other command line arguments. + + See tools/testing/selftests/mm/gup_test.c + +comment "GUP_TEST needs to have DEBUG_FS enabled" + depends on !GUP_TEST && !DEBUG_FS + +config GUP_GET_PXX_LOW_HIGH + bool + +config DMAPOOL_TEST + tristate "Enable a module to run time tests on dma_pool" + depends on HAS_DMA + help + Provides a test module that will allocate and free many blocks of + various sizes and report how long it takes. This is intended to + provide a consistent way to measure how changes to the + dma_pool_alloc/free routines affect performance. + +config ARCH_HAS_PTE_SPECIAL + bool + +# +# Some architectures require a special hugepage directory format that is +# required to support multiple hugepage sizes. For example a4fe3ce76 +# "powerpc/mm: Allow more flexible layouts for hugepage pagetables" +# introduced it on powerpc. This allows for a more flexible hugepage +# pagetable layouts. +# +config ARCH_HAS_HUGEPD + bool + +config MAPPING_DIRTY_HELPERS + bool + +config KMAP_LOCAL + bool + +config KMAP_LOCAL_NON_LINEAR_PTE_ARRAY + bool + +# struct io_mapping based helper. Selected by drivers that need them +config IO_MAPPING + bool + +config MEMFD_CREATE + bool "Enable memfd_create() system call" if EXPERT + +config SECRETMEM + default y + bool "Enable memfd_secret() system call" if EXPERT + depends on ARCH_HAS_SET_DIRECT_MAP + help + Enable the memfd_secret() system call with the ability to create + memory areas visible only in the context of the owning process and + not mapped to other processes and other kernel page tables. + +config ANON_VMA_NAME + bool "Anonymous VMA name support" + depends on PROC_FS && ADVISE_SYSCALLS && MMU + + help + Allow naming anonymous virtual memory areas. + + This feature allows assigning names to virtual memory areas. Assigned + names can be later retrieved from /proc/pid/maps and /proc/pid/smaps + and help identifying individual anonymous memory areas. + Assigning a name to anonymous virtual memory area might prevent that + area from being merged with adjacent virtual memory areas due to the + difference in their name. + +config USERFAULTFD + bool "Enable userfaultfd() system call" + depends on MMU + help + Enable the userfaultfd() system call that allows to intercept and + handle page faults in userland. + +config HAVE_ARCH_USERFAULTFD_WP + bool + help + Arch has userfaultfd write protection support + +config HAVE_ARCH_USERFAULTFD_MINOR + bool + help + Arch has userfaultfd minor fault support + +config PTE_MARKER_UFFD_WP + bool "Userfaultfd write protection support for shmem/hugetlbfs" + default y + depends on HAVE_ARCH_USERFAULTFD_WP + + help + Allows to create marker PTEs for userfaultfd write protection + purposes. It is required to enable userfaultfd write protection on + file-backed memory types like shmem and hugetlbfs. + +# multi-gen LRU { +config LRU_GEN + bool "Multi-Gen LRU" + depends on MMU + # make sure folio->flags has enough spare bits + depends on 64BIT || !SPARSEMEM || SPARSEMEM_VMEMMAP + help + A high performance LRU implementation to overcommit memory. See + Documentation/admin-guide/mm/multigen_lru.rst for details. + +config LRU_GEN_ENABLED + bool "Enable by default" + depends on LRU_GEN + help + This option enables the multi-gen LRU by default. + +config LRU_GEN_STATS + bool "Full stats for debugging" + depends on LRU_GEN + help + Do not enable this option unless you plan to look at historical stats + from evicted generations for debugging purpose. + + This option has a per-memcg and per-node memory overhead. +# } + +config ARCH_SUPPORTS_PER_VMA_LOCK + def_bool n + +config PER_VMA_LOCK + def_bool y + depends on ARCH_SUPPORTS_PER_VMA_LOCK && MMU && SMP + help + Allow per-vma locking during page fault handling. + + This feature allows locking each virtual memory area separately when + handling page faults instead of taking mmap_lock. + +config LOCK_MM_AND_FIND_VMA + bool + depends on !STACK_GROWSUP + +source "mm/damon/Kconfig" + +endmenu |