1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
|
# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/input/microchip,cap11xx.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Microchip CAP11xx based capacitive touch sensors
description: |
The Microchip CAP1xxx Family of RightTouchTM multiple-channel capacitive
touch controllers and LED drivers. The device communication via I2C only.
maintainers:
- Rob Herring <robh@kernel.org>
properties:
compatible:
enum:
- microchip,cap1106
- microchip,cap1126
- microchip,cap1188
- microchip,cap1203
- microchip,cap1206
- microchip,cap1293
- microchip,cap1298
reg:
maxItems: 1
'#address-cells':
const: 1
'#size-cells':
const: 0
interrupts:
maxItems: 1
description: |
Property describing the interrupt line the
device's ALERT#/CM_IRQ# pin is connected to.
The device only has one interrupt source.
autorepeat:
description: |
Enables the Linux input system's autorepeat feature on the input device.
linux,keycodes:
minItems: 6
maxItems: 6
description: |
Specifies an array of numeric keycode values to
be used for the channels. If this property is
omitted, KEY_A, KEY_B, etc are used as defaults.
The array must have exactly six entries.
microchip,sensor-gain:
$ref: /schemas/types.yaml#/definitions/uint32
default: 1
enum: [1, 2, 4, 8]
description: |
Defines the gain of the sensor circuitry. This
effectively controls the sensitivity, as a
smaller delta capacitance is required to
generate the same delta count values.
microchip,irq-active-high:
type: boolean
description: |
By default the interrupt pin is active low
open drain. This property allows using the active
high push-pull output.
patternProperties:
"^led@[0-7]$":
type: object
description: CAP11xx LEDs
$ref: /schemas/leds/common.yaml#
properties:
reg:
enum: [0, 1, 2, 3, 4, 5, 6, 7]
label: true
linux,default-trigger: true
default-state: true
required:
- reg
additionalProperties: false
allOf:
- $ref: input.yaml
- if:
properties:
compatible:
contains:
enum:
- microchip,cap1106
then:
patternProperties:
"^led@[0-7]$": false
required:
- compatible
- interrupts
additionalProperties: false
examples:
- |
i2c {
#address-cells = <1>;
#size-cells = <0>;
touch@28 {
compatible = "microchip,cap1188";
interrupt-parent = <&gpio1>;
interrupts = <0 0>;
reg = <0x28>;
autorepeat;
microchip,sensor-gain = <2>;
linux,keycodes = <103>, /* KEY_UP */
<106>, /* KEY_RIGHT */
<108>, /* KEY_DOWN */
<105>, /* KEY_LEFT */
<109>, /* KEY_PAGEDOWN */
<104>; /* KEY_PAGEUP */
#address-cells = <1>;
#size-cells = <0>;
led@0 {
label = "cap11xx:green:usr0";
reg = <0>;
};
led@1 {
label = "cap11xx:green:usr1";
reg = <1>;
};
led@2 {
label = "cap11xx:green:alive";
reg = <2>;
linux,default-trigger = "heartbeat";
};
};
};
|
