1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/xlnx,axi-ethernet.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: AXI 1G/2.5G Ethernet Subsystem
description: |
Also called AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core
provides connectivity to an external ethernet PHY supporting different
interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two
segments of memory for buffering TX and RX, as well as the capability of
offloading TX/RX checksum calculation off the processor.
Management configuration is done through the AXI interface, while payload is
sent and received through means of an AXI DMA controller. This driver
includes the DMA driver code, so this driver is incompatible with AXI DMA
driver.
maintainers:
- Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
properties:
compatible:
enum:
- xlnx,axi-ethernet-1.00.a
- xlnx,axi-ethernet-1.01.a
- xlnx,axi-ethernet-2.01.a
reg:
description:
Address and length of the IO space, as well as the address
and length of the AXI DMA controller IO space, unless
axistream-connected is specified, in which case the reg
attribute of the node referenced by it is used.
maxItems: 2
interrupts:
items:
- description: Ethernet core interrupt
- description: Tx DMA interrupt
- description: Rx DMA interrupt
description:
Ethernet core interrupt is optional. If axistream-connected property is
present DMA node should contains TX/RX DMA interrupts else DMA interrupt
resources are mentioned on ethernet node.
minItems: 1
phy-handle: true
xlnx,rxmem:
description:
Set to allocated memory buffer for Rx/Tx in the hardware.
$ref: /schemas/types.yaml#/definitions/uint32
phy-mode:
enum:
- mii
- gmii
- rgmii
- sgmii
- 1000BaseX
xlnx,phy-type:
description:
Do not use, but still accepted in preference to phy-mode.
deprecated: true
$ref: /schemas/types.yaml#/definitions/uint32
xlnx,txcsum:
description:
TX checksum offload. 0 or empty for disabling TX checksum offload,
1 to enable partial TX checksum offload and 2 to enable full TX
checksum offload.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1, 2]
xlnx,rxcsum:
description:
RX checksum offload. 0 or empty for disabling RX checksum offload,
1 to enable partial RX checksum offload and 2 to enable full RX
checksum offload.
$ref: /schemas/types.yaml#/definitions/uint32
enum: [0, 1, 2]
xlnx,switch-x-sgmii:
type: boolean
description:
Indicate the Ethernet core is configured to support both 1000BaseX and
SGMII modes. If set, the phy-mode should be set to match the mode
selected on core reset (i.e. by the basex_or_sgmii core input line).
clocks:
items:
- description: Clock for AXI register slave interface.
- description: AXI4-Stream clock for TXD RXD TXC and RXS interfaces.
- description: Ethernet reference clock, used by signal delay primitives
and transceivers.
- description: MGT reference clock (used by optional internal PCS/PMA PHY)
clock-names:
items:
- const: s_axi_lite_clk
- const: axis_clk
- const: ref_clk
- const: mgt_clk
axistream-connected:
$ref: /schemas/types.yaml#/definitions/phandle
description: Phandle of AXI DMA controller which contains the resources
used by this device. If this is specified, the DMA-related resources
from that device (DMA registers and DMA TX/RX interrupts) rather than
this one will be used.
mdio:
type: object
pcs-handle:
description: Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X
modes, where "pcs-handle" should be used to point to the PCS/PMA PHY,
and "phy-handle" should point to an external PHY if exists.
maxItems: 1
required:
- compatible
- interrupts
- reg
- xlnx,rxmem
- phy-handle
allOf:
- $ref: /schemas/net/ethernet-controller.yaml#
additionalProperties: false
examples:
- |
axi_ethernet_eth: ethernet@40c00000 {
compatible = "xlnx,axi-ethernet-1.00.a";
interrupts = <2 0 1>;
clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk";
clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>;
phy-mode = "mii";
reg = <0x40c00000 0x40000>,<0x50c00000 0x40000>;
xlnx,rxcsum = <0x2>;
xlnx,rxmem = <0x800>;
xlnx,txcsum = <0x2>;
phy-handle = <&phy0>;
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy0: ethernet-phy@1 {
device_type = "ethernet-phy";
reg = <1>;
};
};
};
- |
axi_ethernet_eth1: ethernet@40000000 {
compatible = "xlnx,axi-ethernet-1.00.a";
interrupts = <0>;
clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk";
clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>;
phy-mode = "mii";
reg = <0x00 0x40000000 0x00 0x40000>;
xlnx,rxcsum = <0x2>;
xlnx,rxmem = <0x800>;
xlnx,txcsum = <0x2>;
phy-handle = <&phy1>;
axistream-connected = <&dma>;
mdio {
#address-cells = <1>;
#size-cells = <0>;
phy1: ethernet-phy@1 {
device_type = "ethernet-phy";
reg = <1>;
};
};
};
|
