1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
|
* Freescale QorIQ 1588 timer based PTP clock
General Properties:
- compatible Should be "fsl,etsec-ptp" for eTSEC
Should be "fsl,fman-ptp-timer" for DPAA FMan
Should be "fsl,dpaa2-ptp" for DPAA2
Should be "fsl,enetc-ptp" for ENETC
- reg Offset and length of the register set for the device
- interrupts There should be at least two interrupts. Some devices
have as many as four PTP related interrupts.
Clock Properties:
- fsl,cksel Timer reference clock source.
- fsl,tclk-period Timer reference clock period in nanoseconds.
- fsl,tmr-prsc Prescaler, divides the output clock.
- fsl,tmr-add Frequency compensation value.
- fsl,tmr-fiper1 Fixed interval period pulse generator.
- fsl,tmr-fiper2 Fixed interval period pulse generator.
- fsl,tmr-fiper3 Fixed interval period pulse generator.
Supported only on DPAA2 and ENETC hardware.
- fsl,max-adj Maximum frequency adjustment in parts per billion.
- fsl,extts-fifo The presence of this property indicates hardware
support for the external trigger stamp FIFO.
- little-endian The presence of this property indicates the 1588 timer
IP block is little-endian mode. The default endian mode
is big-endian.
These properties set the operational parameters for the PTP
clock. You must choose these carefully for the clock to work right.
Here is how to figure good values:
TimerOsc = selected reference clock MHz
tclk_period = desired clock period nanoseconds
NominalFreq = 1000 / tclk_period MHz
FreqDivRatio = TimerOsc / NominalFreq (must be greater that 1.0)
tmr_add = ceil(2^32 / FreqDivRatio)
OutputClock = NominalFreq / tmr_prsc MHz
PulseWidth = 1 / OutputClock microseconds
FiperFreq1 = desired frequency in Hz
FiperDiv1 = 1000000 * OutputClock / FiperFreq1
tmr_fiper1 = tmr_prsc * tclk_period * FiperDiv1 - tclk_period
max_adj = 1000000000 * (FreqDivRatio - 1.0) - 1
The calculation for tmr_fiper2 is the same as for tmr_fiper1. The
driver expects that tmr_fiper1 will be correctly set to produce a 1
Pulse Per Second (PPS) signal, since this will be offered to the PPS
subsystem to synchronize the Linux clock.
Reference clock source is determined by the value, which is holded
in CKSEL bits in TMR_CTRL register. "fsl,cksel" property keeps the
value, which will be directly written in those bits, that is why,
according to reference manual, the next clock sources can be used:
For eTSEC,
<0> - external high precision timer reference clock (TSEC_TMR_CLK
input is used for this purpose);
<1> - eTSEC system clock;
<2> - eTSEC1 transmit clock;
<3> - RTC clock input.
For DPAA FMan,
<0> - external high precision timer reference clock (TMR_1588_CLK)
<1> - MAC system clock (1/2 FMan clock)
<2> - reserved
<3> - RTC clock oscillator
When this attribute is not used, the IEEE 1588 timer reference clock
will use the eTSEC system clock (for Gianfar) or the MAC system
clock (for DPAA).
Example:
ptp_clock@24e00 {
compatible = "fsl,etsec-ptp";
reg = <0x24E00 0xB0>;
interrupts = <12 0x8 13 0x8>;
interrupt-parent = < &ipic >;
fsl,cksel = <1>;
fsl,tclk-period = <10>;
fsl,tmr-prsc = <100>;
fsl,tmr-add = <0x999999A4>;
fsl,tmr-fiper1 = <0x3B9AC9F6>;
fsl,tmr-fiper2 = <0x00018696>;
fsl,max-adj = <659999998>;
};
|
