1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/regulator/dlg,da9121.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Dialog Semiconductor DA9121 voltage regulator
maintainers:
- Adam Ward <Adam.Ward.opensource@diasemi.com>
description: |
Dialog Semiconductor DA9121 Single-channel 10A double-phase buck converter
Dialog Semiconductor DA9122 Double-channel 5A single-phase buck converter
Dialog Semiconductor DA9220 Double-channel 3A single-phase buck converter
Dialog Semiconductor DA9217 Single-channel 6A double-phase buck converter
Dialog Semiconductor DA9130 Single-channel 10A double-phase buck converter
Dialog Semiconductor DA9131 Double-channel 5A single-phase buck converter
Dialog Semiconductor DA9132 Double-channel 3A single-phase buck converter
Dialog Semiconductor DA9141 Single-channel 40A quad-phase buck converter
Dialog Semiconductor DA9142 Single-channel 20A double-phase buck converter
Device parameter ranges
The current limits can be set to at/near double the rated current per channel
to allow for transient peaks.
Current limit changes when the output is enabled are not supported, as a
precaution against undefined behaviour.
|----------------------------------------------|
| | range & reset default value |
| Device |------------------------------|
| | microvolt | microamp |
|----------------------------------------------|
| DA9121/DA9130 | Min: 300000 | Min: 7000000 |
| | Max: 1900000 | Max: 20000000 |
|----------------------------------------------|
| DA9121/DA9131 | Min: 300000 | Min: 3500000 |
| | Max: 1900000 | Max: 10000000 |
|----------------------------------------------|
| DA9121/DA9131 | Min: 300000 | Min: 3500000 |
| | Max: 1900000 | Max: 6000000 |
|----------------------------------------------|
| DA9217 | Min: 300000 | Min: 7000000 |
| | Max: 1900000 | Max: 12000000 |
|----------------------------------------------|
| DA9141 | Min: 300000 | Min: 26000000 |
| | Max: 1300000 | Max: 78000000 |
|----------------------------------------------|
| DA9142 | Min: 300000 | Min: 13000000 |
| | Max: 1300000 | Max: 39000000 |
|----------------------------------------------|
properties:
$nodename:
pattern: "pmic@[0-9a-f]{1,2}"
compatible:
enum:
- dlg,da9121
- dlg,da9122
- dlg,da9220
- dlg,da9217
- dlg,da9130
- dlg,da9131
- dlg,da9132
- dlg,da9141
- dlg,da9142
reg:
maxItems: 1
description: Specifies the I2C slave address.
interrupts:
maxItems: 1
description: IRQ line information.
dlg,irq-polling-delay-passive-ms:
minimum: 1000
maximum: 10000
description: |
Specify the polling period, measured in milliseconds, between interrupt status
update checks. Range 1000-10000 ms.
regulators:
type: object
additionalProperties: false
description: |
List of regulators provided by the device
patternProperties:
"^buck([1-2])$":
type: object
$ref: regulator.yaml#
description: |
Properties for a single BUCK regulator
properties:
regulator-initial-mode:
enum: [ 0, 1, 2, 3 ]
description: Defined in include/dt-bindings/regulator/dlg,da9121-regulator.h
enable-gpios:
maxItems: 1
description: Specify a valid GPIO for platform control of the regulator
dlg,ripple-cancel:
$ref: /schemas/types.yaml#/definitions/uint32
enum: [ 0, 1, 2, 3 ]
description: |
Defined in include/dt-bindings/regulator/dlg,da9121-regulator.h
Only present on multi-channel devices (DA9122, DA9220, DA9131, DA9132)
unevaluatedProperties: false
required:
- compatible
- reg
- regulators
allOf:
- if:
properties:
compatible:
not:
contains:
enum:
- dlg,da9122
- dlg,da9131
- dlg,da9132
- dlg,da9220
then:
properties:
regulators:
properties:
buck2: false
additionalProperties: false
examples:
- |
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/regulator/dlg,da9121-regulator.h>
i2c {
#address-cells = <1>;
#size-cells = <0>;
pmic@68 {
compatible = "dlg,da9121";
reg = <0x68>;
interrupt-parent = <&gpio6>;
interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
dlg,irq-polling-delay-passive-ms = <2000>;
regulators {
DA9121_BUCK1: buck1 {
regulator-name = "BUCK1";
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <1900000>;
regulator-min-microamp = <7000000>;
regulator-max-microamp = <20000000>;
regulator-boot-on;
regulator-initial-mode = <DA9121_BUCK_MODE_AUTO>;
enable-gpios = <&gpio 1 GPIO_ACTIVE_HIGH>;
};
};
};
};
- |
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/regulator/dlg,da9121-regulator.h>
i2c {
#address-cells = <1>;
#size-cells = <0>;
pmic@68 {
compatible = "dlg,da9122";
reg = <0x68>;
interrupt-parent = <&gpio6>;
interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
dlg,irq-polling-delay-passive-ms = <2000>;
regulators {
DA9122_BUCK1: buck1 {
regulator-name = "BUCK1";
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <1900000>;
regulator-min-microamp = <3500000>;
regulator-max-microamp = <10000000>;
regulator-boot-on;
regulator-initial-mode = <DA9121_BUCK_MODE_AUTO>;
enable-gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>;
dlg,ripple-cancel = <DA9121_BUCK_RIPPLE_CANCEL_NONE>;
};
DA9122_BUCK2: buck2 {
regulator-name = "BUCK2";
regulator-min-microvolt = <300000>;
regulator-max-microvolt = <1900000>;
regulator-min-microamp = <3500000>;
regulator-max-microamp = <10000000>;
regulator-boot-on;
regulator-initial-mode = <DA9121_BUCK_MODE_AUTO>;
enable-gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>;
dlg,ripple-cancel = <DA9121_BUCK_RIPPLE_CANCEL_NONE>;
};
};
};
};
...
|
