1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
|
/*
* Copyright 2015 Hans de Goede <hdegoede@redhat.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include "sunxi-reference-design-tablet.dtsi"
#include "sun8i-reference-design-tablet.dtsi"
/ {
aliases {
serial0 = &r_uart;
/* Make u-boot set mac-address for wifi without an eeprom */
ethernet0 = &sdio_wifi;
};
panel: panel {
/* Tablet dts should provide panel compatible */
backlight = <&backlight>;
enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */
power-supply = <®_dc1sw>;
port {
panel_input: endpoint {
remote-endpoint = <&tcon0_out_lcd>;
};
};
};
wifi_pwrseq: wifi_pwrseq {
compatible = "mmc-pwrseq-simple";
/*
* Q8 boards use various PL# pins as wifi-en. On other boards
* these may be connected to a wifi module output pin. To avoid
* short-circuits we configure these as inputs with pull-ups via
* pinctrl, instead of listing them as active-low reset-gpios.
*/
pinctrl-names = "default";
pinctrl-0 = <&wifi_pwrseq_pin_q8>;
/* The esp8089 needs 200 ms after driving wifi-en high */
post-power-on-delay-ms = <200>;
};
};
&de {
status = "okay";
};
&ehci0 {
status = "okay";
};
&mmc1 {
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pg_pins>;
vmmc-supply = <®_dldo1>;
mmc-pwrseq = <&wifi_pwrseq>;
bus-width = <4>;
non-removable;
status = "okay";
sdio_wifi: sdio_wifi@1 {
reg = <1>;
};
};
&r_pio {
wifi_pwrseq_pin_q8: wifi-pwrseq-pins {
pins = "PL6", "PL7", "PL11";
function = "gpio_in";
bias-pull-up;
};
};
&tcon0 {
pinctrl-names = "default";
pinctrl-0 = <&lcd_rgb666_pins>;
status = "okay";
};
&usbphy {
usb1_vbus-supply = <®_dldo1>;
};
|
