blob: f19efb966d180c11edf842def680c4b81d7c0f2a (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
|
/* SPDX-License-Identifier: GPL-2.0 */
/* PORTSC - Port Status and Control Register - port_status_base bitmasks */
/* true: device connected */
#define PORT_CONNECT (1 << 0)
/* true: port enabled */
#define PORT_PE (1 << 1)
/* bit 2 reserved and zeroed */
/* true: port has an over-current condition */
#define PORT_OC (1 << 3)
/* true: port reset signaling asserted */
#define PORT_RESET (1 << 4)
/* Port Link State - bits 5:8
* A read gives the current link PM state of the port,
* a write with Link State Write Strobe set sets the link state.
*/
#define PORT_PLS_MASK (0xf << 5)
#define XDEV_U0 (0x0 << 5)
#define XDEV_U1 (0x1 << 5)
#define XDEV_U2 (0x2 << 5)
#define XDEV_U3 (0x3 << 5)
#define XDEV_DISABLED (0x4 << 5)
#define XDEV_RXDETECT (0x5 << 5)
#define XDEV_INACTIVE (0x6 << 5)
#define XDEV_POLLING (0x7 << 5)
#define XDEV_RECOVERY (0x8 << 5)
#define XDEV_HOT_RESET (0x9 << 5)
#define XDEV_COMP_MODE (0xa << 5)
#define XDEV_TEST_MODE (0xb << 5)
#define XDEV_RESUME (0xf << 5)
/* true: port has power (see HCC_PPC) */
#define PORT_POWER (1 << 9)
/* bits 10:13 indicate device speed:
* 0 - undefined speed - port hasn't be initialized by a reset yet
* 1 - full speed
* 2 - low speed
* 3 - high speed
* 4 - super speed
* 5-15 reserved
*/
#define DEV_SPEED_MASK (0xf << 10)
#define XDEV_FS (0x1 << 10)
#define XDEV_LS (0x2 << 10)
#define XDEV_HS (0x3 << 10)
#define XDEV_SS (0x4 << 10)
#define XDEV_SSP (0x5 << 10)
#define DEV_UNDEFSPEED(p) (((p) & DEV_SPEED_MASK) == (0x0<<10))
#define DEV_FULLSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_FS)
#define DEV_LOWSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_LS)
#define DEV_HIGHSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_HS)
#define DEV_SUPERSPEED(p) (((p) & DEV_SPEED_MASK) == XDEV_SS)
#define DEV_SUPERSPEEDPLUS(p) (((p) & DEV_SPEED_MASK) == XDEV_SSP)
#define DEV_SUPERSPEED_ANY(p) (((p) & DEV_SPEED_MASK) >= XDEV_SS)
#define DEV_PORT_SPEED(p) (((p) >> 10) & 0x0f)
/* Bits 20:23 in the Slot Context are the speed for the device */
#define SLOT_SPEED_FS (XDEV_FS << 10)
#define SLOT_SPEED_LS (XDEV_LS << 10)
#define SLOT_SPEED_HS (XDEV_HS << 10)
#define SLOT_SPEED_SS (XDEV_SS << 10)
#define SLOT_SPEED_SSP (XDEV_SSP << 10)
/* Port Indicator Control */
#define PORT_LED_OFF (0 << 14)
#define PORT_LED_AMBER (1 << 14)
#define PORT_LED_GREEN (2 << 14)
#define PORT_LED_MASK (3 << 14)
/* Port Link State Write Strobe - set this when changing link state */
#define PORT_LINK_STROBE (1 << 16)
/* true: connect status change */
#define PORT_CSC (1 << 17)
/* true: port enable change */
#define PORT_PEC (1 << 18)
/* true: warm reset for a USB 3.0 device is done. A "hot" reset puts the port
* into an enabled state, and the device into the default state. A "warm" reset
* also resets the link, forcing the device through the link training sequence.
* SW can also look at the Port Reset register to see when warm reset is done.
*/
#define PORT_WRC (1 << 19)
/* true: over-current change */
#define PORT_OCC (1 << 20)
/* true: reset change - 1 to 0 transition of PORT_RESET */
#define PORT_RC (1 << 21)
/* port link status change - set on some port link state transitions:
* Transition Reason
* ------------------------------------------------------------------------------
* - U3 to Resume Wakeup signaling from a device
* - Resume to Recovery to U0 USB 3.0 device resume
* - Resume to U0 USB 2.0 device resume
* - U3 to Recovery to U0 Software resume of USB 3.0 device complete
* - U3 to U0 Software resume of USB 2.0 device complete
* - U2 to U0 L1 resume of USB 2.1 device complete
* - U0 to U0 (???) L1 entry rejection by USB 2.1 device
* - U0 to disabled L1 entry error with USB 2.1 device
* - Any state to inactive Error on USB 3.0 port
*/
#define PORT_PLC (1 << 22)
/* port configure error change - port failed to configure its link partner */
#define PORT_CEC (1 << 23)
#define PORT_CHANGE_MASK (PORT_CSC | PORT_PEC | PORT_WRC | PORT_OCC | \
PORT_RC | PORT_PLC | PORT_CEC)
/* Cold Attach Status - xHC can set this bit to report device attached during
* Sx state. Warm port reset should be perfomed to clear this bit and move port
* to connected state.
*/
#define PORT_CAS (1 << 24)
/* wake on connect (enable) */
#define PORT_WKCONN_E (1 << 25)
/* wake on disconnect (enable) */
#define PORT_WKDISC_E (1 << 26)
/* wake on over-current (enable) */
#define PORT_WKOC_E (1 << 27)
/* bits 28:29 reserved */
/* true: device is non-removable - for USB 3.0 roothub emulation */
#define PORT_DEV_REMOVE (1 << 30)
/* Initiate a warm port reset - complete when PORT_WRC is '1' */
#define PORT_WR (1 << 31)
/* We mark duplicate entries with -1 */
#define DUPLICATE_ENTRY ((u8)(-1))
/* Port Power Management Status and Control - port_power_base bitmasks */
/* Inactivity timer value for transitions into U1, in microseconds.
* Timeout can be up to 127us. 0xFF means an infinite timeout.
*/
#define PORT_U1_TIMEOUT(p) ((p) & 0xff)
#define PORT_U1_TIMEOUT_MASK 0xff
/* Inactivity timer value for transitions into U2 */
#define PORT_U2_TIMEOUT(p) (((p) & 0xff) << 8)
#define PORT_U2_TIMEOUT_MASK (0xff << 8)
/* Bits 24:31 for port testing */
/* USB2 Protocol PORTSPMSC */
#define PORT_L1S_MASK 7
#define PORT_L1S_SUCCESS 1
#define PORT_RWE (1 << 3)
#define PORT_HIRD(p) (((p) & 0xf) << 4)
#define PORT_HIRD_MASK (0xf << 4)
#define PORT_L1DS_MASK (0xff << 8)
#define PORT_L1DS(p) (((p) & 0xff) << 8)
#define PORT_HLE (1 << 16)
#define PORT_TEST_MODE_SHIFT 28
/* USB3 Protocol PORTLI Port Link Information */
#define PORT_RX_LANES(p) (((p) >> 16) & 0xf)
#define PORT_TX_LANES(p) (((p) >> 20) & 0xf)
/* USB2 Protocol PORTHLPMC */
#define PORT_HIRDM(p)((p) & 3)
#define PORT_L1_TIMEOUT(p)(((p) & 0xff) << 2)
#define PORT_BESLD(p)(((p) & 0xf) << 10)
/* use 512 microseconds as USB2 LPM L1 default timeout. */
#define XHCI_L1_TIMEOUT 512
/* Set default HIRD/BESL value to 4 (350/400us) for USB2 L1 LPM resume latency.
* Safe to use with mixed HIRD and BESL systems (host and device) and is used
* by other operating systems.
*
* XHCI 1.0 errata 8/14/12 Table 13 notes:
* "Software should choose xHC BESL/BESLD field values that do not violate a
* device's resume latency requirements,
* e.g. not program values > '4' if BLC = '1' and a HIRD device is attached,
* or not program values < '4' if BLC = '0' and a BESL device is attached.
*/
#define XHCI_DEFAULT_BESL 4
/*
* USB3 specification define a 360ms tPollingLFPSTiemout for USB3 ports
* to complete link training. usually link trainig completes much faster
* so check status 10 times with 36ms sleep in places we need to wait for
* polling to complete.
*/
#define XHCI_PORT_POLLING_LFPS_TIME 36
|
