Merging upstream version 256.

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 332 insertions, 68 deletions

diff --git a/src/basic/linux/nl80211.h b/src/basic/linux/nl80211.h
index c14a91b..f23ecbd 100644
--- a/src/basic/linux/nl80211.h
+++ b/src/basic/linux/nl80211.h
@@ -11,7 +11,7 @@
  * Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
  * Copyright 2008 Colin McCabe <colin@cozybit.com>
  * Copyright 2015-2017	Intel Deutschland GmbH
- * Copyright (C) 2018-2022 Intel Corporation
+ * Copyright (C) 2018-2024 Intel Corporation
  *
  * Permission to use, copy, modify, and/or distribute this software for any
  * purpose with or without fee is hereby granted, provided that the above
@@ -72,7 +72,7 @@
  * For drivers supporting TDLS with external setup (WIPHY_FLAG_SUPPORTS_TDLS
  * and WIPHY_FLAG_TDLS_EXTERNAL_SETUP), the station lifetime is as follows:
  *  - a setup station entry is added, not yet authorized, without any rate
- *    or capability information, this just exists to avoid race conditions
+ *    or capability information; this just exists to avoid race conditions
  *  - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid
  *    to add rate and capability information to the station and at the same
  *    time mark it authorized.
@@ -87,7 +87,7 @@
  * DOC: Frame transmission/registration support
  *
  * Frame transmission and registration support exists to allow userspace
- * management entities such as wpa_supplicant react to management frames
+ * management entities such as wpa_supplicant to react to management frames
  * that are not being handled by the kernel. This includes, for example,
  * certain classes of action frames that cannot be handled in the kernel
  * for various reasons.
@@ -113,7 +113,7 @@
  *
  * Frame transmission allows userspace to send for example the required
  * responses to action frames. It is subject to some sanity checking,
- * but many frames can be transmitted. When a frame was transmitted, its
+ * but many frames can be transmitted. When a frame is transmitted, its
  * status is indicated to the sending socket.
  *
  * For more technical details, see the corresponding command descriptions
@@ -123,7 +123,7 @@
 /**
  * DOC: Virtual interface / concurrency capabilities
  *
- * Some devices are able to operate with virtual MACs, they can have
+ * Some devices are able to operate with virtual MACs; they can have
  * more than one virtual interface. The capability handling for this
  * is a bit complex though, as there may be a number of restrictions
  * on the types of concurrency that are supported.
@@ -135,7 +135,7 @@
  * Once concurrency is desired, more attributes must be observed:
  * To start with, since some interface types are purely managed in
  * software, like the AP-VLAN type in mac80211 for example, there's
- * an additional list of these, they can be added at any time and
+ * an additional list of these; they can be added at any time and
  * are only restricted by some semantic restrictions (e.g. AP-VLAN
  * cannot be added without a corresponding AP interface). This list
  * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute.
@@ -164,17 +164,17 @@
  * Packet coalesce feature helps to reduce number of received interrupts
  * to host by buffering these packets in firmware/hardware for some
  * predefined time. Received interrupt will be generated when one of the
- * following events occur.
+ * following events occurs.
  * a) Expiration of hardware timer whose expiration time is set to maximum
  * coalescing delay of matching coalesce rule.
- * b) Coalescing buffer in hardware reaches it's limit.
+ * b) Coalescing buffer in hardware reaches its limit.
  * c) Packet doesn't match any of the configured coalesce rules.
  *
  * User needs to configure following parameters for creating a coalesce
  * rule.
  * a) Maximum coalescing delay
  * b) List of packet patterns which needs to be matched
- * c) Condition for coalescence. pattern 'match' or 'no match'
+ * c) Condition for coalescence: pattern 'match' or 'no match'
  * Multiple such rules can be created.
  */
 
@@ -213,7 +213,7 @@
 /**
  * DOC: FILS shared key authentication offload
  *
- * FILS shared key authentication offload can be advertized by drivers by
+ * FILS shared key authentication offload can be advertised by drivers by
  * setting @NL80211_EXT_FEATURE_FILS_SK_OFFLOAD flag. The drivers that support
  * FILS shared key authentication offload should be able to construct the
  * authentication and association frames for FILS shared key authentication and
@@ -239,7 +239,7 @@
  * The PMKSA can be maintained in userspace persistently so that it can be used
  * later after reboots or wifi turn off/on also.
  *
- * %NL80211_ATTR_FILS_CACHE_ID is the cache identifier advertized by a FILS
+ * %NL80211_ATTR_FILS_CACHE_ID is the cache identifier advertised by a FILS
  * capable AP supporting PMK caching. It specifies the scope within which the
  * PMKSAs are cached in an ESS. %NL80211_CMD_SET_PMKSA and
  * %NL80211_CMD_DEL_PMKSA are enhanced to allow support for PMKSA caching based
@@ -290,12 +290,12 @@
  * If the configuration needs to be applied for specific peer then the MAC
  * address of the peer needs to be passed in %NL80211_ATTR_MAC, otherwise the
  * configuration will be applied for all the connected peers in the vif except
- * any peers that have peer specific configuration for the TID by default; if
- * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer specific values
+ * any peers that have peer-specific configuration for the TID by default; if
+ * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer-specific values
  * will be overwritten.
  *
- * All this configuration is valid only for STA's current connection
- * i.e. the configuration will be reset to default when the STA connects back
+ * All this configuration is valid only for STA's current connection,
+ * i.e., the configuration will be reset to default when the STA connects back
  * after disconnection/roaming, and this configuration will be cleared when
  * the interface goes down.
  */
@@ -326,7 +326,7 @@
 /**
  * DOC: Multi-Link Operation
  *
- * In Multi-Link Operation, a connection between to MLDs utilizes multiple
+ * In Multi-Link Operation, a connection between two MLDs utilizes multiple
  * links. To use this in nl80211, various commands and responses now need
  * to or will include the new %NL80211_ATTR_MLO_LINKS attribute.
  * Additionally, various commands that need to operate on a specific link
@@ -335,6 +335,15 @@
  */
 
 /**
+ * DOC: OWE DH IE handling offload
+ *
+ * By setting @NL80211_EXT_FEATURE_OWE_OFFLOAD flag, drivers can indicate
+ * kernel/application space to avoid DH IE handling. When this flag is
+ * advertised, the driver/device will take care of DH IE inclusion and
+ * processing of peer DH IE to generate PMK.
+ */
+
+/**
  * enum nl80211_commands - supported nl80211 commands
  *
  * @NL80211_CMD_UNSPEC: unspecified command to catch errors
@@ -424,11 +433,13 @@
  *	interface identified by %NL80211_ATTR_IFINDEX.
  * @NL80211_CMD_DEL_STATION: Remove a station identified by %NL80211_ATTR_MAC
  *	or, if no MAC address given, all stations, on the interface identified
- *	by %NL80211_ATTR_IFINDEX. %NL80211_ATTR_MGMT_SUBTYPE and
+ *	by %NL80211_ATTR_IFINDEX. For MLD station, MLD address is used in
+ *	%NL80211_ATTR_MAC. %NL80211_ATTR_MGMT_SUBTYPE and
  *	%NL80211_ATTR_REASON_CODE can optionally be used to specify which type
  *	of disconnection indication should be sent to the station
  *	(Deauthentication or Disassociation frame and reason code for that
- *	frame).
+ *	frame). %NL80211_ATTR_MLO_LINK_ID can be used optionally to remove
+ *	stations connected and using at least that link as one of its links.
  *
  * @NL80211_CMD_GET_MPATH: Get mesh path attributes for mesh path to
  * 	destination %NL80211_ATTR_MAC on the interface identified by
@@ -511,7 +522,7 @@
  *	%NL80211_ATTR_SCHED_SCAN_PLANS. If %NL80211_ATTR_SCHED_SCAN_PLANS is
  *	not specified and only %NL80211_ATTR_SCHED_SCAN_INTERVAL is specified,
  *	scheduled scan will run in an infinite loop with the specified interval.
- *	These attributes are mutually exculsive,
+ *	These attributes are mutually exclusive,
  *	i.e. NL80211_ATTR_SCHED_SCAN_INTERVAL must not be passed if
  *	NL80211_ATTR_SCHED_SCAN_PLANS is defined.
  *	If for some reason scheduled scan is aborted by the driver, all scan
@@ -542,7 +553,7 @@
  *	%NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface
  *	is brought down while a scheduled scan was running.
  *
- * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
+ * @NL80211_CMD_GET_SURVEY: get survey results, e.g. channel occupation
  *      or noise level
  * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
  *	NL80211_CMD_GET_SURVEY and on the "scan" multicast group)
@@ -553,12 +564,13 @@
  *	using %NL80211_ATTR_SSID, %NL80211_ATTR_FILS_CACHE_ID,
  *	%NL80211_ATTR_PMKID, and %NL80211_ATTR_PMK in case of FILS
  *	authentication where %NL80211_ATTR_FILS_CACHE_ID is the identifier
- *	advertized by a FILS capable AP identifying the scope of PMKSA in an
+ *	advertised by a FILS capable AP identifying the scope of PMKSA in an
  *	ESS.
  * @NL80211_CMD_DEL_PMKSA: Delete a PMKSA cache entry, using %NL80211_ATTR_MAC
  *	(for the BSSID) and %NL80211_ATTR_PMKID or using %NL80211_ATTR_SSID,
  *	%NL80211_ATTR_FILS_CACHE_ID, and %NL80211_ATTR_PMKID in case of FILS
- *	authentication.
+ *	authentication. Additionally in case of SAE offload and OWE offloads
+ *	PMKSA entry can be deleted using %NL80211_ATTR_SSID.
  * @NL80211_CMD_FLUSH_PMKSA: Flush all PMKSA cache entries.
  *
  * @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain
@@ -597,7 +609,7 @@
  *	BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify
  *	the SSID (mainly for association, but is included in authentication
  *	request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ +
- *	%NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequence of the
+ *	%NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequency of the
  *	channel in MHz. %NL80211_ATTR_AUTH_TYPE is used to specify the
  *	authentication type. %NL80211_ATTR_IE is used to define IEs
  *	(VendorSpecificInfo, but also including RSN IE and FT IEs) to be added
@@ -806,7 +818,7 @@
  *	reached.
  * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
  *	and the attributes determining channel width) the given interface
- *	(identifed by %NL80211_ATTR_IFINDEX) shall operate on.
+ *	(identified by %NL80211_ATTR_IFINDEX) shall operate on.
  *	In case multiple channels are supported by the device, the mechanism
  *	with which it switches channels is implementation-defined.
  *	When a monitor interface is given, it can only switch channel while
@@ -878,7 +890,7 @@
  *	inform userspace of the new replay counter.
  *
  * @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace
- *	of PMKSA caching dandidates.
+ *	of PMKSA caching candidates.
  *
  * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
  *	In addition, this can be used as an event to request userspace to take
@@ -914,7 +926,7 @@
  *
  * @NL80211_CMD_PROBE_CLIENT: Probe an associated station on an AP interface
  *	by sending a null data frame to it and reporting when the frame is
- *	acknowleged. This is used to allow timing out inactive clients. Uses
+ *	acknowledged. This is used to allow timing out inactive clients. Uses
  *	%NL80211_ATTR_IFINDEX and %NL80211_ATTR_MAC. The command returns a
  *	direct reply with an %NL80211_ATTR_COOKIE that is later used to match
  *	up the event with the request. The event includes the same data and
@@ -1125,11 +1137,15 @@
  * @NL80211_CMD_DEL_PMK: For offloaded 4-Way handshake, delete the previously
  *	configured PMK for the authenticator address identified by
  *	%NL80211_ATTR_MAC.
- * @NL80211_CMD_PORT_AUTHORIZED: An event that indicates an 802.1X FT roam was
- *	completed successfully. Drivers that support 4 way handshake offload
- *	should send this event after indicating 802.1X FT assocation with
- *	%NL80211_CMD_ROAM. If the 4 way handshake failed %NL80211_CMD_DISCONNECT
- *	should be indicated instead.
+ * @NL80211_CMD_PORT_AUTHORIZED: An event that indicates port is authorized and
+ *	open for regular data traffic. For STA/P2P-client, this event is sent
+ *	with AP MAC address and for AP/P2P-GO, the event carries the STA/P2P-
+ *	client MAC address.
+ *	Drivers that support 4 way handshake offload should send this event for
+ *	STA/P2P-client after successful 4-way HS or after 802.1X FT following
+ *	NL80211_CMD_CONNECT or NL80211_CMD_ROAM. Drivers using AP/P2P-GO 4-way
+ *	handshake offload should send this event on successful completion of
+ *	4-way handshake with the peer (STA/P2P-client).
  * @NL80211_CMD_CONTROL_PORT_FRAME: Control Port (e.g. PAE) frame TX request
  *	and RX notification.  This command is used both as a request to transmit
  *	a control port frame and as a notification that a control port frame
@@ -1166,6 +1182,23 @@
  *	%NL80211_ATTR_STATUS_CODE attribute in %NL80211_CMD_EXTERNAL_AUTH
  *	command interface.
  *
+ *	Host driver sends MLD address of the AP with %NL80211_ATTR_MLD_ADDR in
+ *	%NL80211_CMD_EXTERNAL_AUTH event to indicate user space to enable MLO
+ *	during the authentication offload in STA mode while connecting to MLD
+ *	APs. Host driver should check %NL80211_ATTR_MLO_SUPPORT flag capability
+ *	in %NL80211_CMD_CONNECT to know whether the user space supports enabling
+ *	MLO during the authentication offload or not.
+ *	User space should enable MLO during the authentication only when it
+ *	receives the AP MLD address in authentication offload request. User
+ *	space shouldn't enable MLO when the authentication offload request
+ *	doesn't indicate the AP MLD address even if the AP is MLO capable.
+ *	User space should use %NL80211_ATTR_MLD_ADDR as peer's MLD address and
+ *	interface address identified by %NL80211_ATTR_IFINDEX as self MLD
+ *	address. User space and host driver to use MLD addresses in RA, TA and
+ *	BSSID fields of the frames between them, and host driver translates the
+ *	MLD addresses to/from link addresses based on the link chosen for the
+ *	authentication.
+ *
  *	Host driver reports this status on an authentication failure to the
  *	user space through the connect result as the user space would have
  *	initiated the connection through the connect request.
@@ -1281,6 +1314,26 @@
  * @NL80211_CMD_MODIFY_LINK_STA: Modify a link of an MLD station
  * @NL80211_CMD_REMOVE_LINK_STA: Remove a link of an MLD station
  *
+ * @NL80211_CMD_SET_HW_TIMESTAMP: Enable/disable HW timestamping of Timing
+ *	measurement and Fine timing measurement frames. If %NL80211_ATTR_MAC
+ *	is included, enable/disable HW timestamping only for frames to/from the
+ *	specified MAC address. Otherwise enable/disable HW timestamping for
+ *	all TM/FTM frames (including ones that were enabled with specific MAC
+ *	address). If %NL80211_ATTR_HW_TIMESTAMP_ENABLED is not included, disable
+ *	HW timestamping.
+ *	The number of peers that HW timestamping can be enabled for concurrently
+ *	is indicated by %NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS.
+ *
+ * @NL80211_CMD_LINKS_REMOVED: Notify userspace about the removal of STA MLD
+ *	setup links due to AP MLD removing the corresponding affiliated APs with
+ *	Multi-Link reconfiguration. %NL80211_ATTR_MLO_LINKS is used to provide
+ *	information about the removed STA MLD setup links.
+ *
+ * @NL80211_CMD_SET_TID_TO_LINK_MAPPING: Set the TID to Link Mapping for a
+ *      non-AP MLD station. The %NL80211_ATTR_MLO_TTLM_DLINK and
+ *      %NL80211_ATTR_MLO_TTLM_ULINK attributes are used to specify the
+ *      TID to Link mapping for downlink/uplink traffic.
+ *
  * @NL80211_CMD_MAX: highest used command number
  * @__NL80211_CMD_AFTER_LAST: internal use
  */
@@ -1532,6 +1585,12 @@ enum nl80211_commands {
 	NL80211_CMD_MODIFY_LINK_STA,
 	NL80211_CMD_REMOVE_LINK_STA,
 
+	NL80211_CMD_SET_HW_TIMESTAMP,
+
+	NL80211_CMD_LINKS_REMOVED,
+
+	NL80211_CMD_SET_TID_TO_LINK_MAPPING,
+
 	/* add new commands above here */
 
 	/* used to define NL80211_CMD_MAX below */
@@ -1789,7 +1848,7 @@ enum nl80211_commands {
  *	using %CMD_CONTROL_PORT_FRAME.  If control port routing over NL80211 is
  *	to be used then userspace must also use the %NL80211_ATTR_SOCKET_OWNER
  *	flag. When used with %NL80211_ATTR_CONTROL_PORT_NO_PREAUTH, pre-auth
- *	frames are not forwared over the control port.
+ *	frames are not forwarded over the control port.
  *
  * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
  *	We recommend using nested, driver-specific attributes within this.
@@ -1926,10 +1985,10 @@ enum nl80211_commands {
  *	bit. Depending on which antennas are selected in the bitmap, 802.11n
  *	drivers can derive which chainmasks to use (if all antennas belonging to
  *	a particular chain are disabled this chain should be disabled) and if
- *	a chain has diversity antennas wether diversity should be used or not.
+ *	a chain has diversity antennas whether diversity should be used or not.
  *	HT capabilities (STBC, TX Beamforming, Antenna selection) can be
  *	derived from the available chains after applying the antenna mask.
- *	Non-802.11n drivers can derive wether to use diversity or not.
+ *	Non-802.11n drivers can derive whether to use diversity or not.
  *	Drivers may reject configurations or RX/TX mask combinations they cannot
  *	support by returning -EINVAL.
  *
@@ -2499,7 +2558,7 @@ enum nl80211_commands {
  *	from successful FILS authentication and is used with
  *	%NL80211_CMD_CONNECT.
  *
- * @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertized by a FILS AP
+ * @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertised by a FILS AP
  *	identifying the scope of PMKSAs. This is used with
  *	@NL80211_CMD_SET_PMKSA and @NL80211_CMD_DEL_PMKSA.
  *
@@ -2653,11 +2712,13 @@ enum nl80211_commands {
  *
  * @NL80211_ATTR_FILS_DISCOVERY: Optional parameter to configure FILS
  *	discovery. It is a nested attribute, see
- *	&enum nl80211_fils_discovery_attributes.
+ *	&enum nl80211_fils_discovery_attributes. Userspace should pass an empty
+ *	nested attribute to disable this feature and delete the templates.
  *
  * @NL80211_ATTR_UNSOL_BCAST_PROBE_RESP: Optional parameter to configure
  *	unsolicited broadcast probe response. It is a nested attribute, see
- *	&enum nl80211_unsol_bcast_probe_resp_attributes.
+ *	&enum nl80211_unsol_bcast_probe_resp_attributes. Userspace should pass an empty
+ *	nested attribute to disable this feature and delete the templates.
  *
  * @NL80211_ATTR_S1G_CAPABILITY: S1G Capability information element (from
  *	association request when used with NL80211_CMD_NEW_STATION)
@@ -2751,6 +2812,50 @@ enum nl80211_commands {
  *	the incoming frame RX timestamp.
  * @NL80211_ATTR_TD_BITMAP: Transition Disable bitmap, for subsequent
  *	(re)associations.
+ *
+ * @NL80211_ATTR_PUNCT_BITMAP: (u32) Preamble puncturing bitmap, lowest
+ *	bit corresponds to the lowest 20 MHz channel. Each bit set to 1
+ *	indicates that the sub-channel is punctured. Higher 16 bits are
+ *	reserved.
+ *
+ * @NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS: Maximum number of peers that HW
+ *	timestamping can be enabled for concurrently (u16), a wiphy attribute.
+ *	A value of 0xffff indicates setting for all peers (i.e. not specifying
+ *	an address with %NL80211_CMD_SET_HW_TIMESTAMP) is supported.
+ * @NL80211_ATTR_HW_TIMESTAMP_ENABLED: Indicates whether HW timestamping should
+ *	be enabled or not (flag attribute).
+ *
+ * @NL80211_ATTR_EMA_RNR_ELEMS: Optional nested attribute for
+ *	reduced neighbor report (RNR) elements. This attribute can be used
+ *	only when NL80211_MBSSID_CONFIG_ATTR_EMA is enabled.
+ *	Userspace is responsible for splitting the RNR into multiple
+ *	elements such that each element excludes the non-transmitting
+ *	profiles already included in the MBSSID element
+ *	(%NL80211_ATTR_MBSSID_ELEMS) at the same index. Each EMA beacon
+ *	will be generated by adding MBSSID and RNR elements at the same
+ *	index. If the userspace includes more RNR elements than number of
+ *	MBSSID elements then these will be added in every EMA beacon.
+ *
+ * @NL80211_ATTR_MLO_LINK_DISABLED: Flag attribute indicating that the link is
+ *	disabled.
+ *
+ * @NL80211_ATTR_BSS_DUMP_INCLUDE_USE_DATA: Include BSS usage data, i.e.
+ *	include BSSes that can only be used in restricted scenarios and/or
+ *	cannot be used at all.
+ *
+ * @NL80211_ATTR_MLO_TTLM_DLINK: Binary attribute specifying the downlink TID to
+ *      link mapping. The length is 8 * sizeof(u16). For each TID the link
+ *      mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element)
+ *      in Draft P802.11be_D4.0.
+ * @NL80211_ATTR_MLO_TTLM_ULINK: Binary attribute specifying the uplink TID to
+ *      link mapping. The length is 8 * sizeof(u16). For each TID the link
+ *      mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element)
+ *      in Draft P802.11be_D4.0.
+ *
+ * @NL80211_ATTR_ASSOC_SPP_AMSDU: flag attribute used with
+ *	%NL80211_CMD_ASSOCIATE indicating the SPP A-MSDUs
+ *	are used on this connection
+ *
  * @NUM_NL80211_ATTR: total number of nl80211_attrs available
  * @NL80211_ATTR_MAX: highest attribute number currently defined
  * @__NL80211_ATTR_AFTER_LAST: internal use
@@ -3280,6 +3385,22 @@ enum nl80211_attrs {
 	NL80211_ATTR_RX_HW_TIMESTAMP,
 	NL80211_ATTR_TD_BITMAP,
 
+	NL80211_ATTR_PUNCT_BITMAP,
+
+	NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS,
+	NL80211_ATTR_HW_TIMESTAMP_ENABLED,
+
+	NL80211_ATTR_EMA_RNR_ELEMS,
+
+	NL80211_ATTR_MLO_LINK_DISABLED,
+
+	NL80211_ATTR_BSS_DUMP_INCLUDE_USE_DATA,
+
+	NL80211_ATTR_MLO_TTLM_DLINK,
+	NL80211_ATTR_MLO_TTLM_ULINK,
+
+	NL80211_ATTR_ASSOC_SPP_AMSDU,
+
 	/* add attributes here, update the policy in nl80211.c */
 
 	__NL80211_ATTR_AFTER_LAST,
@@ -3420,6 +3541,7 @@ enum nl80211_iftype {
  * @NL80211_STA_FLAG_ASSOCIATED: station is associated; used with drivers
  *	that support %NL80211_FEATURE_FULL_AP_CLIENT_STATE to transition a
  *	previously added station into associated state
+ * @NL80211_STA_FLAG_SPP_AMSDU: station supports SPP A-MSDUs
  * @NL80211_STA_FLAG_MAX: highest station flag number currently defined
  * @__NL80211_STA_FLAG_AFTER_LAST: internal use
  */
@@ -3432,6 +3554,7 @@ enum nl80211_sta_flags {
 	NL80211_STA_FLAG_AUTHENTICATED,
 	NL80211_STA_FLAG_TDLS_PEER,
 	NL80211_STA_FLAG_ASSOCIATED,
+	NL80211_STA_FLAG_SPP_AMSDU,
 
 	/* keep last */
 	__NL80211_STA_FLAG_AFTER_LAST,
@@ -3606,6 +3729,13 @@ enum nl80211_eht_ru_alloc {
  *	(u8, see &enum nl80211_eht_gi)
  * @NL80211_RATE_INFO_EHT_RU_ALLOC: EHT RU allocation, if not present then
  *	non-OFDMA was used (u8, see &enum nl80211_eht_ru_alloc)
+ * @NL80211_RATE_INFO_S1G_MCS: S1G MCS index (u8, 0-10)
+ * @NL80211_RATE_INFO_S1G_NSS: S1G NSS value (u8, 1-4)
+ * @NL80211_RATE_INFO_1_MHZ_WIDTH: 1 MHz S1G rate
+ * @NL80211_RATE_INFO_2_MHZ_WIDTH: 2 MHz S1G rate
+ * @NL80211_RATE_INFO_4_MHZ_WIDTH: 4 MHz S1G rate
+ * @NL80211_RATE_INFO_8_MHZ_WIDTH: 8 MHz S1G rate
+ * @NL80211_RATE_INFO_16_MHZ_WIDTH: 16 MHz S1G rate
  * @__NL80211_RATE_INFO_AFTER_LAST: internal use
  */
 enum nl80211_rate_info {
@@ -3632,6 +3762,13 @@ enum nl80211_rate_info {
 	NL80211_RATE_INFO_EHT_NSS,
 	NL80211_RATE_INFO_EHT_GI,
 	NL80211_RATE_INFO_EHT_RU_ALLOC,
+	NL80211_RATE_INFO_S1G_MCS,
+	NL80211_RATE_INFO_S1G_NSS,
+	NL80211_RATE_INFO_1_MHZ_WIDTH,
+	NL80211_RATE_INFO_2_MHZ_WIDTH,
+	NL80211_RATE_INFO_4_MHZ_WIDTH,
+	NL80211_RATE_INFO_8_MHZ_WIDTH,
+	NL80211_RATE_INFO_16_MHZ_WIDTH,
 
 	/* keep last */
 	__NL80211_RATE_INFO_AFTER_LAST,
@@ -4000,6 +4137,10 @@ enum nl80211_band_iftype_attr {
  * @NL80211_BAND_ATTR_EDMG_BW_CONFIG: Channel BW Configuration subfield encodes
  *	the allowed channel bandwidth configurations.
  *	Defined by IEEE P802.11ay/D4.0 section 9.4.2.251, Table 13.
+ * @NL80211_BAND_ATTR_S1G_MCS_NSS_SET: S1G capabilities, supported S1G-MCS and NSS
+ *	set subfield, as in the S1G information IE, 5 bytes
+ * @NL80211_BAND_ATTR_S1G_CAPA: S1G capabilities information subfield as in the
+ *	S1G information IE, 10 bytes
  * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
  * @__NL80211_BAND_ATTR_AFTER_LAST: internal use
  */
@@ -4020,6 +4161,9 @@ enum nl80211_band_attr {
 	NL80211_BAND_ATTR_EDMG_CHANNELS,
 	NL80211_BAND_ATTR_EDMG_BW_CONFIG,
 
+	NL80211_BAND_ATTR_S1G_MCS_NSS_SET,
+	NL80211_BAND_ATTR_S1G_CAPA,
+
 	/* keep last */
 	__NL80211_BAND_ATTR_AFTER_LAST,
 	NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1
@@ -4065,7 +4209,7 @@ enum nl80211_wmm_rule {
  *	(100 * dBm).
  * @NL80211_FREQUENCY_ATTR_DFS_STATE: current state for DFS
  *	(enum nl80211_dfs_state)
- * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in miliseconds for how long
+ * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in milliseconds for how long
  *	this channel is in this DFS state.
  * @NL80211_FREQUENCY_ATTR_NO_HT40_MINUS: HT40- isn't possible with this
  *	channel as the control channel
@@ -4119,6 +4263,19 @@ enum nl80211_wmm_rule {
  *	as the primary or any of the secondary channels isn't possible
  * @NL80211_FREQUENCY_ATTR_NO_EHT: EHT operation is not allowed on this channel
  *	in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_PSD: Power spectral density (in dBm) that
+ *	is allowed on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_DFS_CONCURRENT: Operation on this channel is
+ *	allowed for peer-to-peer or adhoc communication under the control
+ *	of a DFS master which operates on the same channel (FCC-594280 D01
+ *	Section B.3). Should be used together with %NL80211_RRF_DFS only.
+ * @NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT: Client connection to VLP AP
+ *	not allowed using this channel
+ * @NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT: Client connection to AFC AP
+ *	not allowed using this channel
+ * @NL80211_FREQUENCY_ATTR_CAN_MONITOR: This channel can be used in monitor
+ *	mode despite other (regulatory) restrictions, even if the channel is
+ *	otherwise completely disabled.
  * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
  *	currently defined
  * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
@@ -4157,6 +4314,11 @@ enum nl80211_frequency_attr {
 	NL80211_FREQUENCY_ATTR_16MHZ,
 	NL80211_FREQUENCY_ATTR_NO_320MHZ,
 	NL80211_FREQUENCY_ATTR_NO_EHT,
+	NL80211_FREQUENCY_ATTR_PSD,
+	NL80211_FREQUENCY_ATTR_DFS_CONCURRENT,
+	NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT,
+	NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT,
+	NL80211_FREQUENCY_ATTR_CAN_MONITOR,
 
 	/* keep last */
 	__NL80211_FREQUENCY_ATTR_AFTER_LAST,
@@ -4169,6 +4331,10 @@ enum nl80211_frequency_attr {
 #define NL80211_FREQUENCY_ATTR_NO_IR		NL80211_FREQUENCY_ATTR_NO_IR
 #define NL80211_FREQUENCY_ATTR_GO_CONCURRENT \
 					NL80211_FREQUENCY_ATTR_IR_CONCURRENT
+#define NL80211_FREQUENCY_ATTR_NO_UHB_VLP_CLIENT \
+	NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT
+#define NL80211_FREQUENCY_ATTR_NO_UHB_AFC_CLIENT \
+	NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT
 
 /**
  * enum nl80211_bitrate_attr - bitrate attributes
@@ -4257,6 +4423,8 @@ enum nl80211_reg_type {
  * 	a given frequency range. The value is in mBm (100 * dBm).
  * @NL80211_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
  *	If not present or 0 default CAC time will be used.
+ * @NL80211_ATTR_POWER_RULE_PSD: power spectral density (in dBm).
+ *	This could be negative.
  * @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
  *	currently defined
  * @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use
@@ -4274,6 +4442,8 @@ enum nl80211_reg_rule_attr {
 
 	NL80211_ATTR_DFS_CAC_TIME,
 
+	NL80211_ATTR_POWER_RULE_PSD,
+
 	/* keep last */
 	__NL80211_REG_RULE_ATTR_AFTER_LAST,
 	NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1
@@ -4302,14 +4472,7 @@ enum nl80211_reg_rule_attr {
  *	value as specified by &struct nl80211_bss_select_rssi_adjust.
  * @NL80211_SCHED_SCAN_MATCH_ATTR_BSSID: BSSID to be used for matching
  *	(this cannot be used together with SSID).
- * @NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI: Nested attribute that carries the
- *	band specific minimum rssi thresholds for the bands defined in
- *	enum nl80211_band. The minimum rssi threshold value(s32) specific to a
- *	band shall be encapsulated in attribute with type value equals to one
- *	of the NL80211_BAND_* defined in enum nl80211_band. For example, the
- *	minimum rssi threshold value for 2.4GHZ band shall be encapsulated
- *	within an attribute of type NL80211_BAND_2GHZ. And one or more of such
- *	attributes will be nested within this attribute.
+ * @NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI: Obsolete
  * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter
  *	attribute number currently defined
  * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use
@@ -4322,7 +4485,7 @@ enum nl80211_sched_scan_match_attr {
 	NL80211_SCHED_SCAN_MATCH_ATTR_RELATIVE_RSSI,
 	NL80211_SCHED_SCAN_MATCH_ATTR_RSSI_ADJUST,
 	NL80211_SCHED_SCAN_MATCH_ATTR_BSSID,
-	NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI,
+	NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI, /* obsolete */
 
 	/* keep last */
 	__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST,
@@ -4356,6 +4519,14 @@ enum nl80211_sched_scan_match_attr {
  * @NL80211_RRF_NO_160MHZ: 160MHz operation not allowed
  * @NL80211_RRF_NO_HE: HE operation not allowed
  * @NL80211_RRF_NO_320MHZ: 320MHz operation not allowed
+ * @NL80211_RRF_NO_EHT: EHT operation not allowed
+ * @NL80211_RRF_PSD: Ruleset has power spectral density value
+ * @NL80211_RRF_DFS_CONCURRENT: Operation on this channel is allowed for
+	peer-to-peer or adhoc communication under the control of a DFS master
+	which operates on the same channel (FCC-594280 D01 Section B.3).
+	Should be used together with %NL80211_RRF_DFS only.
+ * @NL80211_RRF_NO_6GHZ_VLP_CLIENT: Client connection to VLP AP not allowed
+ * @NL80211_RRF_NO_6GHZ_AFC_CLIENT: Client connection to AFC AP not allowed
  */
 enum nl80211_reg_rule_flags {
 	NL80211_RRF_NO_OFDM		= 1<<0,
@@ -4375,6 +4546,11 @@ enum nl80211_reg_rule_flags {
 	NL80211_RRF_NO_160MHZ		= 1<<16,
 	NL80211_RRF_NO_HE		= 1<<17,
 	NL80211_RRF_NO_320MHZ		= 1<<18,
+	NL80211_RRF_NO_EHT		= 1<<19,
+	NL80211_RRF_PSD			= 1<<20,
+	NL80211_RRF_DFS_CONCURRENT	= 1<<21,
+	NL80211_RRF_NO_6GHZ_VLP_CLIENT	= 1<<22,
+	NL80211_RRF_NO_6GHZ_AFC_CLIENT	= 1<<23,
 };
 
 #define NL80211_RRF_PASSIVE_SCAN	NL80211_RRF_NO_IR
@@ -4383,6 +4559,8 @@ enum nl80211_reg_rule_flags {
 #define NL80211_RRF_NO_HT40		(NL80211_RRF_NO_HT40MINUS |\
 					 NL80211_RRF_NO_HT40PLUS)
 #define NL80211_RRF_GO_CONCURRENT	NL80211_RRF_IR_CONCURRENT
+#define NL80211_RRF_NO_UHB_VLP_CLIENT	NL80211_RRF_NO_6GHZ_VLP_CLIENT
+#define NL80211_RRF_NO_UHB_AFC_CLIENT	NL80211_RRF_NO_6GHZ_AFC_CLIENT
 
 /* For backport compatibility with older userspace */
 #define NL80211_RRF_NO_IR_ALL		(NL80211_RRF_NO_IR | __NL80211_RRF_NO_IBSS)
@@ -4912,6 +5090,36 @@ enum nl80211_bss_scan_width {
 };
 
 /**
+ * enum nl80211_bss_use_for - bitmap indicating possible BSS use
+ * @NL80211_BSS_USE_FOR_NORMAL: Use this BSS for normal "connection",
+ *	including IBSS/MBSS depending on the type.
+ * @NL80211_BSS_USE_FOR_MLD_LINK: This BSS can be used as a link in an
+ *	MLO connection. Note that for an MLO connection, all links including
+ *	the assoc link must have this flag set, and the assoc link must
+ *	additionally have %NL80211_BSS_USE_FOR_NORMAL set.
+ */
+enum nl80211_bss_use_for {
+	NL80211_BSS_USE_FOR_NORMAL = 1 << 0,
+	NL80211_BSS_USE_FOR_MLD_LINK = 1 << 1,
+};
+
+/**
+ * enum nl80211_bss_cannot_use_reasons - reason(s) connection to a
+ *	BSS isn't possible
+ * @NL80211_BSS_CANNOT_USE_NSTR_NONPRIMARY: NSTR nonprimary links aren't
+ *	supported by the device, and this BSS entry represents one.
+ * @NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH: STA is not supporting
+ *	the AP power type (SP, VLP, AP) that the AP uses.
+ */
+enum nl80211_bss_cannot_use_reasons {
+	NL80211_BSS_CANNOT_USE_NSTR_NONPRIMARY	= 1 << 0,
+	NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH	= 1 << 1,
+};
+
+#define NL80211_BSS_CANNOT_USE_UHB_PWR_MISMATCH \
+	NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH
+
+/**
  * enum nl80211_bss - netlink attributes for a BSS
  *
  * @__NL80211_BSS_INVALID: invalid
@@ -4942,7 +5150,7 @@ enum nl80211_bss_scan_width {
  *	elements from a Beacon frame (bin); not present if no Beacon frame has
  *	yet been received
  * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
- *	(u32, enum nl80211_bss_scan_width)
+ *	(u32, enum nl80211_bss_scan_width) - No longer used!
  * @NL80211_BSS_BEACON_TSF: TSF of the last received beacon (u64)
  *	(not present if no beacon frame has been received yet)
  * @NL80211_BSS_PRESP_DATA: the data in @NL80211_BSS_INFORMATION_ELEMENTS and
@@ -4963,6 +5171,14 @@ enum nl80211_bss_scan_width {
  * @NL80211_BSS_FREQUENCY_OFFSET: frequency offset in KHz
  * @NL80211_BSS_MLO_LINK_ID: MLO link ID of the BSS (u8).
  * @NL80211_BSS_MLD_ADDR: MLD address of this BSS if connected to it.
+ * @NL80211_BSS_USE_FOR: u32 bitmap attribute indicating what the BSS can be
+ *	used for, see &enum nl80211_bss_use_for.
+ * @NL80211_BSS_CANNOT_USE_REASONS: Indicates the reason that this BSS cannot
+ *	be used for all or some of the possible uses by the device reporting it,
+ *	even though its presence was detected.
+ *	This is a u64 attribute containing a bitmap of values from
+ *	&enum nl80211_cannot_use_reasons, note that the attribute may be missing
+ *	if no reasons are specified.
  * @__NL80211_BSS_AFTER_LAST: internal
  * @NL80211_BSS_MAX: highest BSS attribute
  */
@@ -4990,6 +5206,8 @@ enum nl80211_bss {
 	NL80211_BSS_FREQUENCY_OFFSET,
 	NL80211_BSS_MLO_LINK_ID,
 	NL80211_BSS_MLD_ADDR,
+	NL80211_BSS_USE_FOR,
+	NL80211_BSS_CANNOT_USE_REASONS,
 
 	/* keep last */
 	__NL80211_BSS_AFTER_LAST,
@@ -5338,7 +5556,7 @@ enum nl80211_tx_rate_setting {
  *	(%NL80211_TID_CONFIG_ATTR_TIDS, %NL80211_TID_CONFIG_ATTR_OVERRIDE).
  * @NL80211_TID_CONFIG_ATTR_PEER_SUPP: same as the previous per-vif one, but
  *	per peer instead.
- * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribue, if set indicates
+ * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribute, if set indicates
  *	that the new configuration overrides all previous peer
  *	configurations, otherwise previous peer specific configurations
  *	should be left untouched.
@@ -5539,6 +5757,8 @@ struct nl80211_pattern_support {
  *	%NL80211_ATTR_SCAN_FREQUENCIES contains more than one
  *	frequency, it means that the match occurred in more than one
  *	channel.
+ * @NL80211_WOWLAN_TRIG_UNPROTECTED_DEAUTH_DISASSOC: For wakeup reporting only.
+ *	Wake up happened due to unprotected deauth or disassoc frame in MFP.
  * @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers
  * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number
  *
@@ -5566,6 +5786,7 @@ enum nl80211_wowlan_triggers {
 	NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS,
 	NL80211_WOWLAN_TRIG_NET_DETECT,
 	NL80211_WOWLAN_TRIG_NET_DETECT_RESULTS,
+	NL80211_WOWLAN_TRIG_UNPROTECTED_DEAUTH_DISASSOC,
 
 	/* keep last */
 	NUM_NL80211_WOWLAN_TRIG,
@@ -5721,7 +5942,7 @@ enum nl80211_attr_coalesce_rule {
 
 /**
  * enum nl80211_coalesce_condition - coalesce rule conditions
- * @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns
+ * @NL80211_COALESCE_CONDITION_MATCH: coalesce Rx packets when patterns
  *	in a rule are matched.
  * @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns
  *	in a rule are not matched.
@@ -5820,7 +6041,7 @@ enum nl80211_if_combination_attrs {
  * enum nl80211_plink_state - state of a mesh peer link finite state machine
  *
  * @NL80211_PLINK_LISTEN: initial state, considered the implicit
- *	state of non existent mesh peer links
+ *	state of non-existent mesh peer links
  * @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to
  *	this mesh peer
  * @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received
@@ -5869,6 +6090,7 @@ enum plink_actions {
 #define NL80211_KEK_LEN			16
 #define NL80211_KCK_EXT_LEN		24
 #define NL80211_KEK_EXT_LEN		32
+#define NL80211_KCK_EXT_LEN_32		32
 #define NL80211_REPLAY_CTR_LEN		8
 
 /**
@@ -6112,7 +6334,7 @@ enum nl80211_feature_flags {
  *	request to use RRM (see %NL80211_ATTR_USE_RRM) with
  *	%NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests, which will set
  *	the ASSOC_REQ_USE_RRM flag in the association request even if
- *	NL80211_FEATURE_QUIET is not advertized.
+ *	NL80211_FEATURE_QUIET is not advertised.
  * @NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER: This device supports MU-MIMO air
  *	sniffer which means that it can be configured to hear packets from
  *	certain groups which can be configured by the
@@ -6124,13 +6346,15 @@ enum nl80211_feature_flags {
  *	the BSS that the interface that requested the scan is connected to
  *	(if available).
  * @NL80211_EXT_FEATURE_BSS_PARENT_TSF: Per BSS, this driver reports the
- *	time the last beacon/probe was received. The time is the TSF of the
- *	BSS that the interface that requested the scan is connected to
- *	(if available).
+ *	time the last beacon/probe was received. For a non-MLO connection, the
+ *	time is the TSF of the BSS that the interface that requested the scan is
+ *	connected to (if available). For an MLO connection, the time is the TSF
+ *	of the BSS corresponding with link ID specified in the scan request (if
+ *	specified).
  * @NL80211_EXT_FEATURE_SET_SCAN_DWELL: This driver supports configuration of
  *	channel dwell time.
  * @NL80211_EXT_FEATURE_BEACON_RATE_LEGACY: Driver supports beacon rate
- *	configuration (AP/mesh), supporting a legacy (non HT/VHT) rate.
+ *	configuration (AP/mesh), supporting a legacy (non-HT/VHT) rate.
  * @NL80211_EXT_FEATURE_BEACON_RATE_HT: Driver supports beacon rate
  *	configuration (AP/mesh) with HT rates.
  * @NL80211_EXT_FEATURE_BEACON_RATE_VHT: Driver supports beacon rate
@@ -6204,8 +6428,7 @@ enum nl80211_feature_flags {
  * @NL80211_EXT_FEATURE_AP_PMKSA_CACHING: Driver/device supports PMKSA caching
  *	(set/del PMKSA operations) in AP mode.
  *
- * @NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD: Driver supports
- *	filtering of sched scan results using band specific RSSI thresholds.
+ * @NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD: Obsolete
  *
  * @NL80211_EXT_FEATURE_STA_TX_PWR: This driver supports controlling tx power
  *	to a station.
@@ -6294,6 +6517,31 @@ enum nl80211_feature_flags {
  *	might apply, e.g. no scans in progress, no offchannel operations
  *	in progress, and no active connections.
  *
+ * @NL80211_EXT_FEATURE_PUNCT: Driver supports preamble puncturing in AP mode.
+ *
+ * @NL80211_EXT_FEATURE_SECURE_NAN: Device supports NAN Pairing which enables
+ *	authentication, data encryption and message integrity.
+ *
+ * @NL80211_EXT_FEATURE_AUTH_AND_DEAUTH_RANDOM_TA: Device supports randomized TA
+ *	in authentication and deauthentication frames sent to unassociated peer
+ *	using @NL80211_CMD_FRAME.
+ *
+ * @NL80211_EXT_FEATURE_OWE_OFFLOAD: Driver/Device wants to do OWE DH IE
+ *	handling in station mode.
+ *
+ * @NL80211_EXT_FEATURE_OWE_OFFLOAD_AP: Driver/Device wants to do OWE DH IE
+ *	handling in AP mode.
+ *
+ * @NL80211_EXT_FEATURE_DFS_CONCURRENT: The device supports peer-to-peer or
+ *	ad hoc operation on DFS channels under the control of a concurrent
+ *	DFS master on the same channel as described in FCC-594280 D01
+ *	(Section B.3). This, for example, allows P2P GO and P2P clients to
+ *	operate on DFS channels as long as there's a concurrent BSS connection.
+ *
+ * @NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT: The driver has support for SPP
+ *	(signaling and payload protected) A-MSDUs and this shall be advertised
+ *	in the RSNXE.
+ *
  * @NUM_NL80211_EXT_FEATURES: number of extended features.
  * @MAX_NL80211_EXT_FEATURES: highest extended feature index.
  */
@@ -6335,7 +6583,7 @@ enum nl80211_ext_feature_index {
 	NL80211_EXT_FEATURE_ENABLE_FTM_RESPONDER,
 	NL80211_EXT_FEATURE_AIRTIME_FAIRNESS,
 	NL80211_EXT_FEATURE_AP_PMKSA_CACHING,
-	NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD,
+	NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD, /* obsolete */
 	NL80211_EXT_FEATURE_EXT_KEY_ID,
 	NL80211_EXT_FEATURE_STA_TX_PWR,
 	NL80211_EXT_FEATURE_SAE_OFFLOAD,
@@ -6362,6 +6610,13 @@ enum nl80211_ext_feature_index {
 	NL80211_EXT_FEATURE_FILS_CRYPTO_OFFLOAD,
 	NL80211_EXT_FEATURE_RADAR_BACKGROUND,
 	NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE,
+	NL80211_EXT_FEATURE_PUNCT,
+	NL80211_EXT_FEATURE_SECURE_NAN,
+	NL80211_EXT_FEATURE_AUTH_AND_DEAUTH_RANDOM_TA,
+	NL80211_EXT_FEATURE_OWE_OFFLOAD,
+	NL80211_EXT_FEATURE_OWE_OFFLOAD_AP,
+	NL80211_EXT_FEATURE_DFS_CONCURRENT,
+	NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT,
 
 	/* add new features before the definition below */
 	NUM_NL80211_EXT_FEATURES,
@@ -6446,7 +6701,7 @@ enum nl80211_timeout_reason {
  *	request parameters IE in the probe request
  * @NL80211_SCAN_FLAG_ACCEPT_BCAST_PROBE_RESP: accept broadcast probe responses
  * @NL80211_SCAN_FLAG_OCE_PROBE_REQ_HIGH_TX_RATE: send probe request frames at
- *	rate of at least 5.5M. In case non OCE AP is discovered in the channel,
+ *	rate of at least 5.5M. In case non-OCE AP is discovered in the channel,
  *	only the first probe req in the channel will be sent in high rate.
  * @NL80211_SCAN_FLAG_OCE_PROBE_REQ_DEFERRAL_SUPPRESSION: allow probe request
  *	tx deferral (dot11FILSProbeDelay shall be set to 15ms)
@@ -6476,8 +6731,16 @@ enum nl80211_timeout_reason {
  * @NL80211_SCAN_FLAG_FREQ_KHZ: report scan results with
  *	%NL80211_ATTR_SCAN_FREQ_KHZ. This also means
  *	%NL80211_ATTR_SCAN_FREQUENCIES will not be included.
- * @NL80211_SCAN_FLAG_COLOCATED_6GHZ: scan for colocated APs reported by
- *	2.4/5 GHz APs
+ * @NL80211_SCAN_FLAG_COLOCATED_6GHZ: scan for collocated APs reported by
+ *	2.4/5 GHz APs. When the flag is set, the scan logic will use the
+ *	information from the RNR element found in beacons/probe responses
+ *	received on the 2.4/5 GHz channels to actively scan only the 6GHz
+ *	channels on which APs are expected to be found. Note that when not set,
+ *	the scan logic would scan all 6GHz channels, but since transmission of
+ *	probe requests on non-PSC channels is limited, it is highly likely that
+ *	these channels would passively be scanned. Also note that when the flag
+ *	is set, in addition to the colocated APs, PSC channels would also be
+ *	scanned if the user space has asked for it.
  */
 enum nl80211_scan_flags {
 	NL80211_SCAN_FLAG_LOW_PRIORITY				= 1<<0,
@@ -6806,7 +7069,7 @@ enum nl80211_nan_func_term_reason {
  *	The instance ID for the follow up Service Discovery Frame. This is u8.
  * @NL80211_NAN_FUNC_FOLLOW_UP_REQ_ID: relevant if the function's type
  *	is follow up. This is a u8.
- *	The requestor instance ID for the follow up Service Discovery Frame.
+ *	The requester instance ID for the follow up Service Discovery Frame.
  * @NL80211_NAN_FUNC_FOLLOW_UP_DEST: the MAC address of the recipient of the
  *	follow up Service Discovery Frame. This is a binary attribute.
  * @NL80211_NAN_FUNC_CLOSE_RANGE: is this function limited for devices in a
@@ -7196,7 +7459,7 @@ enum nl80211_peer_measurement_attrs {
  * @NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED: flag attribute indicating if
  *	trigger based ranging measurement is supported
  * @NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED: flag attribute indicating
- *	if non trigger based ranging measurement is supported
+ *	if non-trigger-based ranging measurement is supported
  *
  * @NUM_NL80211_PMSR_FTM_CAPA_ATTR: internal
  * @NL80211_PMSR_FTM_CAPA_ATTR_MAX: highest attribute number
@@ -7250,7 +7513,7 @@ enum nl80211_peer_measurement_ftm_capa {
  *      if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
  *	%NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
  *	ranging will be used.
- * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non trigger based
+ * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non-trigger-based
  *	ranging measurement (flag)
  *	This attribute and %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED are
  *	mutually exclusive.
@@ -7328,7 +7591,7 @@ enum nl80211_peer_measurement_ftm_failure_reasons {
  * @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_ATTEMPTS: number of FTM Request frames
  *	transmitted (u32, optional)
  * @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_SUCCESSES: number of FTM Request frames
- *	that were acknowleged (u32, optional)
+ *	that were acknowledged (u32, optional)
  * @NL80211_PMSR_FTM_RESP_ATTR_BUSY_RETRY_TIME: retry time received from the
  *	busy peer (u32, seconds)
  * @NL80211_PMSR_FTM_RESP_ATTR_NUM_BURSTS_EXP: actual number of bursts exponent
@@ -7489,7 +7752,7 @@ enum nl80211_iftype_akm_attributes {
  * @NL80211_FILS_DISCOVERY_ATTR_INT_MIN: Minimum packet interval (u32, TU).
  *	Allowed range: 0..10000 (TU = Time Unit)
  * @NL80211_FILS_DISCOVERY_ATTR_INT_MAX: Maximum packet interval (u32, TU).
- *	Allowed range: 0..10000 (TU = Time Unit)
+ *	Allowed range: 0..10000 (TU = Time Unit). If set to 0, the feature is disabled.
  * @NL80211_FILS_DISCOVERY_ATTR_TMPL: Template data for FILS discovery action
  *	frame including the headers.
  *
@@ -7522,7 +7785,8 @@ enum nl80211_fils_discovery_attributes {
  *
  * @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INT: Maximum packet interval (u32, TU).
  *	Allowed range: 0..20 (TU = Time Unit). IEEE P802.11ax/D6.0
- *	26.17.2.3.2 (AP behavior for fast passive scanning).
+ *	26.17.2.3.2 (AP behavior for fast passive scanning). If set to 0, the feature is
+ *	disabled.
  * @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_TMPL: Unsolicited broadcast probe response
  *	frame template (binary).
  *