summaryrefslogtreecommitdiffstats
path: root/src/basic/linux/nl80211.h
diff options
context:
space:
mode:
Diffstat (limited to 'src/basic/linux/nl80211.h')
-rw-r--r--src/basic/linux/nl80211.h400
1 files changed, 332 insertions, 68 deletions
diff --git a/src/basic/linux/nl80211.h b/src/basic/linux/nl80211.h
index c14a91b..f23ecbd 100644
--- a/src/basic/linux/nl80211.h
+++ b/src/basic/linux/nl80211.h
@@ -11,7 +11,7 @@
* Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
* Copyright 2008 Colin McCabe <colin@cozybit.com>
* Copyright 2015-2017 Intel Deutschland GmbH
- * Copyright (C) 2018-2022 Intel Corporation
+ * Copyright (C) 2018-2024 Intel Corporation
*
* Permission to use, copy, modify, and/or distribute this software for any
* purpose with or without fee is hereby granted, provided that the above
@@ -72,7 +72,7 @@
* For drivers supporting TDLS with external setup (WIPHY_FLAG_SUPPORTS_TDLS
* and WIPHY_FLAG_TDLS_EXTERNAL_SETUP), the station lifetime is as follows:
* - a setup station entry is added, not yet authorized, without any rate
- * or capability information, this just exists to avoid race conditions
+ * or capability information; this just exists to avoid race conditions
* - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid
* to add rate and capability information to the station and at the same
* time mark it authorized.
@@ -87,7 +87,7 @@
* DOC: Frame transmission/registration support
*
* Frame transmission and registration support exists to allow userspace
- * management entities such as wpa_supplicant react to management frames
+ * management entities such as wpa_supplicant to react to management frames
* that are not being handled by the kernel. This includes, for example,
* certain classes of action frames that cannot be handled in the kernel
* for various reasons.
@@ -113,7 +113,7 @@
*
* Frame transmission allows userspace to send for example the required
* responses to action frames. It is subject to some sanity checking,
- * but many frames can be transmitted. When a frame was transmitted, its
+ * but many frames can be transmitted. When a frame is transmitted, its
* status is indicated to the sending socket.
*
* For more technical details, see the corresponding command descriptions
@@ -123,7 +123,7 @@
/**
* DOC: Virtual interface / concurrency capabilities
*
- * Some devices are able to operate with virtual MACs, they can have
+ * Some devices are able to operate with virtual MACs; they can have
* more than one virtual interface. The capability handling for this
* is a bit complex though, as there may be a number of restrictions
* on the types of concurrency that are supported.
@@ -135,7 +135,7 @@
* Once concurrency is desired, more attributes must be observed:
* To start with, since some interface types are purely managed in
* software, like the AP-VLAN type in mac80211 for example, there's
- * an additional list of these, they can be added at any time and
+ * an additional list of these; they can be added at any time and
* are only restricted by some semantic restrictions (e.g. AP-VLAN
* cannot be added without a corresponding AP interface). This list
* is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute.
@@ -164,17 +164,17 @@
* Packet coalesce feature helps to reduce number of received interrupts
* to host by buffering these packets in firmware/hardware for some
* predefined time. Received interrupt will be generated when one of the
- * following events occur.
+ * following events occurs.
* a) Expiration of hardware timer whose expiration time is set to maximum
* coalescing delay of matching coalesce rule.
- * b) Coalescing buffer in hardware reaches it's limit.
+ * b) Coalescing buffer in hardware reaches its limit.
* c) Packet doesn't match any of the configured coalesce rules.
*
* User needs to configure following parameters for creating a coalesce
* rule.
* a) Maximum coalescing delay
* b) List of packet patterns which needs to be matched
- * c) Condition for coalescence. pattern 'match' or 'no match'
+ * c) Condition for coalescence: pattern 'match' or 'no match'
* Multiple such rules can be created.
*/
@@ -213,7 +213,7 @@
/**
* DOC: FILS shared key authentication offload
*
- * FILS shared key authentication offload can be advertized by drivers by
+ * FILS shared key authentication offload can be advertised by drivers by
* setting @NL80211_EXT_FEATURE_FILS_SK_OFFLOAD flag. The drivers that support
* FILS shared key authentication offload should be able to construct the
* authentication and association frames for FILS shared key authentication and
@@ -239,7 +239,7 @@
* The PMKSA can be maintained in userspace persistently so that it can be used
* later after reboots or wifi turn off/on also.
*
- * %NL80211_ATTR_FILS_CACHE_ID is the cache identifier advertized by a FILS
+ * %NL80211_ATTR_FILS_CACHE_ID is the cache identifier advertised by a FILS
* capable AP supporting PMK caching. It specifies the scope within which the
* PMKSAs are cached in an ESS. %NL80211_CMD_SET_PMKSA and
* %NL80211_CMD_DEL_PMKSA are enhanced to allow support for PMKSA caching based
@@ -290,12 +290,12 @@
* If the configuration needs to be applied for specific peer then the MAC
* address of the peer needs to be passed in %NL80211_ATTR_MAC, otherwise the
* configuration will be applied for all the connected peers in the vif except
- * any peers that have peer specific configuration for the TID by default; if
- * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer specific values
+ * any peers that have peer-specific configuration for the TID by default; if
+ * the %NL80211_TID_CONFIG_ATTR_OVERRIDE flag is set, peer-specific values
* will be overwritten.
*
- * All this configuration is valid only for STA's current connection
- * i.e. the configuration will be reset to default when the STA connects back
+ * All this configuration is valid only for STA's current connection,
+ * i.e., the configuration will be reset to default when the STA connects back
* after disconnection/roaming, and this configuration will be cleared when
* the interface goes down.
*/
@@ -326,7 +326,7 @@
/**
* DOC: Multi-Link Operation
*
- * In Multi-Link Operation, a connection between to MLDs utilizes multiple
+ * In Multi-Link Operation, a connection between two MLDs utilizes multiple
* links. To use this in nl80211, various commands and responses now need
* to or will include the new %NL80211_ATTR_MLO_LINKS attribute.
* Additionally, various commands that need to operate on a specific link
@@ -335,6 +335,15 @@
*/
/**
+ * DOC: OWE DH IE handling offload
+ *
+ * By setting @NL80211_EXT_FEATURE_OWE_OFFLOAD flag, drivers can indicate
+ * kernel/application space to avoid DH IE handling. When this flag is
+ * advertised, the driver/device will take care of DH IE inclusion and
+ * processing of peer DH IE to generate PMK.
+ */
+
+/**
* enum nl80211_commands - supported nl80211 commands
*
* @NL80211_CMD_UNSPEC: unspecified command to catch errors
@@ -424,11 +433,13 @@
* interface identified by %NL80211_ATTR_IFINDEX.
* @NL80211_CMD_DEL_STATION: Remove a station identified by %NL80211_ATTR_MAC
* or, if no MAC address given, all stations, on the interface identified
- * by %NL80211_ATTR_IFINDEX. %NL80211_ATTR_MGMT_SUBTYPE and
+ * by %NL80211_ATTR_IFINDEX. For MLD station, MLD address is used in
+ * %NL80211_ATTR_MAC. %NL80211_ATTR_MGMT_SUBTYPE and
* %NL80211_ATTR_REASON_CODE can optionally be used to specify which type
* of disconnection indication should be sent to the station
* (Deauthentication or Disassociation frame and reason code for that
- * frame).
+ * frame). %NL80211_ATTR_MLO_LINK_ID can be used optionally to remove
+ * stations connected and using at least that link as one of its links.
*
* @NL80211_CMD_GET_MPATH: Get mesh path attributes for mesh path to
* destination %NL80211_ATTR_MAC on the interface identified by
@@ -511,7 +522,7 @@
* %NL80211_ATTR_SCHED_SCAN_PLANS. If %NL80211_ATTR_SCHED_SCAN_PLANS is
* not specified and only %NL80211_ATTR_SCHED_SCAN_INTERVAL is specified,
* scheduled scan will run in an infinite loop with the specified interval.
- * These attributes are mutually exculsive,
+ * These attributes are mutually exclusive,
* i.e. NL80211_ATTR_SCHED_SCAN_INTERVAL must not be passed if
* NL80211_ATTR_SCHED_SCAN_PLANS is defined.
* If for some reason scheduled scan is aborted by the driver, all scan
@@ -542,7 +553,7 @@
* %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface
* is brought down while a scheduled scan was running.
*
- * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
+ * @NL80211_CMD_GET_SURVEY: get survey results, e.g. channel occupation
* or noise level
* @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
* NL80211_CMD_GET_SURVEY and on the "scan" multicast group)
@@ -553,12 +564,13 @@
* using %NL80211_ATTR_SSID, %NL80211_ATTR_FILS_CACHE_ID,
* %NL80211_ATTR_PMKID, and %NL80211_ATTR_PMK in case of FILS
* authentication where %NL80211_ATTR_FILS_CACHE_ID is the identifier
- * advertized by a FILS capable AP identifying the scope of PMKSA in an
+ * advertised by a FILS capable AP identifying the scope of PMKSA in an
* ESS.
* @NL80211_CMD_DEL_PMKSA: Delete a PMKSA cache entry, using %NL80211_ATTR_MAC
* (for the BSSID) and %NL80211_ATTR_PMKID or using %NL80211_ATTR_SSID,
* %NL80211_ATTR_FILS_CACHE_ID, and %NL80211_ATTR_PMKID in case of FILS
- * authentication.
+ * authentication. Additionally in case of SAE offload and OWE offloads
+ * PMKSA entry can be deleted using %NL80211_ATTR_SSID.
* @NL80211_CMD_FLUSH_PMKSA: Flush all PMKSA cache entries.
*
* @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain
@@ -597,7 +609,7 @@
* BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify
* the SSID (mainly for association, but is included in authentication
* request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ +
- * %NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequence of the
+ * %NL80211_ATTR_WIPHY_FREQ_OFFSET is used to specify the frequency of the
* channel in MHz. %NL80211_ATTR_AUTH_TYPE is used to specify the
* authentication type. %NL80211_ATTR_IE is used to define IEs
* (VendorSpecificInfo, but also including RSN IE and FT IEs) to be added
@@ -806,7 +818,7 @@
* reached.
* @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
* and the attributes determining channel width) the given interface
- * (identifed by %NL80211_ATTR_IFINDEX) shall operate on.
+ * (identified by %NL80211_ATTR_IFINDEX) shall operate on.
* In case multiple channels are supported by the device, the mechanism
* with which it switches channels is implementation-defined.
* When a monitor interface is given, it can only switch channel while
@@ -878,7 +890,7 @@
* inform userspace of the new replay counter.
*
* @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace
- * of PMKSA caching dandidates.
+ * of PMKSA caching candidates.
*
* @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
* In addition, this can be used as an event to request userspace to take
@@ -914,7 +926,7 @@
*
* @NL80211_CMD_PROBE_CLIENT: Probe an associated station on an AP interface
* by sending a null data frame to it and reporting when the frame is
- * acknowleged. This is used to allow timing out inactive clients. Uses
+ * acknowledged. This is used to allow timing out inactive clients. Uses
* %NL80211_ATTR_IFINDEX and %NL80211_ATTR_MAC. The command returns a
* direct reply with an %NL80211_ATTR_COOKIE that is later used to match
* up the event with the request. The event includes the same data and
@@ -1125,11 +1137,15 @@
* @NL80211_CMD_DEL_PMK: For offloaded 4-Way handshake, delete the previously
* configured PMK for the authenticator address identified by
* %NL80211_ATTR_MAC.
- * @NL80211_CMD_PORT_AUTHORIZED: An event that indicates an 802.1X FT roam was
- * completed successfully. Drivers that support 4 way handshake offload
- * should send this event after indicating 802.1X FT assocation with
- * %NL80211_CMD_ROAM. If the 4 way handshake failed %NL80211_CMD_DISCONNECT
- * should be indicated instead.
+ * @NL80211_CMD_PORT_AUTHORIZED: An event that indicates port is authorized and
+ * open for regular data traffic. For STA/P2P-client, this event is sent
+ * with AP MAC address and for AP/P2P-GO, the event carries the STA/P2P-
+ * client MAC address.
+ * Drivers that support 4 way handshake offload should send this event for
+ * STA/P2P-client after successful 4-way HS or after 802.1X FT following
+ * NL80211_CMD_CONNECT or NL80211_CMD_ROAM. Drivers using AP/P2P-GO 4-way
+ * handshake offload should send this event on successful completion of
+ * 4-way handshake with the peer (STA/P2P-client).
* @NL80211_CMD_CONTROL_PORT_FRAME: Control Port (e.g. PAE) frame TX request
* and RX notification. This command is used both as a request to transmit
* a control port frame and as a notification that a control port frame
@@ -1166,6 +1182,23 @@
* %NL80211_ATTR_STATUS_CODE attribute in %NL80211_CMD_EXTERNAL_AUTH
* command interface.
*
+ * Host driver sends MLD address of the AP with %NL80211_ATTR_MLD_ADDR in
+ * %NL80211_CMD_EXTERNAL_AUTH event to indicate user space to enable MLO
+ * during the authentication offload in STA mode while connecting to MLD
+ * APs. Host driver should check %NL80211_ATTR_MLO_SUPPORT flag capability
+ * in %NL80211_CMD_CONNECT to know whether the user space supports enabling
+ * MLO during the authentication offload or not.
+ * User space should enable MLO during the authentication only when it
+ * receives the AP MLD address in authentication offload request. User
+ * space shouldn't enable MLO when the authentication offload request
+ * doesn't indicate the AP MLD address even if the AP is MLO capable.
+ * User space should use %NL80211_ATTR_MLD_ADDR as peer's MLD address and
+ * interface address identified by %NL80211_ATTR_IFINDEX as self MLD
+ * address. User space and host driver to use MLD addresses in RA, TA and
+ * BSSID fields of the frames between them, and host driver translates the
+ * MLD addresses to/from link addresses based on the link chosen for the
+ * authentication.
+ *
* Host driver reports this status on an authentication failure to the
* user space through the connect result as the user space would have
* initiated the connection through the connect request.
@@ -1281,6 +1314,26 @@
* @NL80211_CMD_MODIFY_LINK_STA: Modify a link of an MLD station
* @NL80211_CMD_REMOVE_LINK_STA: Remove a link of an MLD station
*
+ * @NL80211_CMD_SET_HW_TIMESTAMP: Enable/disable HW timestamping of Timing
+ * measurement and Fine timing measurement frames. If %NL80211_ATTR_MAC
+ * is included, enable/disable HW timestamping only for frames to/from the
+ * specified MAC address. Otherwise enable/disable HW timestamping for
+ * all TM/FTM frames (including ones that were enabled with specific MAC
+ * address). If %NL80211_ATTR_HW_TIMESTAMP_ENABLED is not included, disable
+ * HW timestamping.
+ * The number of peers that HW timestamping can be enabled for concurrently
+ * is indicated by %NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS.
+ *
+ * @NL80211_CMD_LINKS_REMOVED: Notify userspace about the removal of STA MLD
+ * setup links due to AP MLD removing the corresponding affiliated APs with
+ * Multi-Link reconfiguration. %NL80211_ATTR_MLO_LINKS is used to provide
+ * information about the removed STA MLD setup links.
+ *
+ * @NL80211_CMD_SET_TID_TO_LINK_MAPPING: Set the TID to Link Mapping for a
+ * non-AP MLD station. The %NL80211_ATTR_MLO_TTLM_DLINK and
+ * %NL80211_ATTR_MLO_TTLM_ULINK attributes are used to specify the
+ * TID to Link mapping for downlink/uplink traffic.
+ *
* @NL80211_CMD_MAX: highest used command number
* @__NL80211_CMD_AFTER_LAST: internal use
*/
@@ -1532,6 +1585,12 @@ enum nl80211_commands {
NL80211_CMD_MODIFY_LINK_STA,
NL80211_CMD_REMOVE_LINK_STA,
+ NL80211_CMD_SET_HW_TIMESTAMP,
+
+ NL80211_CMD_LINKS_REMOVED,
+
+ NL80211_CMD_SET_TID_TO_LINK_MAPPING,
+
/* add new commands above here */
/* used to define NL80211_CMD_MAX below */
@@ -1789,7 +1848,7 @@ enum nl80211_commands {
* using %CMD_CONTROL_PORT_FRAME. If control port routing over NL80211 is
* to be used then userspace must also use the %NL80211_ATTR_SOCKET_OWNER
* flag. When used with %NL80211_ATTR_CONTROL_PORT_NO_PREAUTH, pre-auth
- * frames are not forwared over the control port.
+ * frames are not forwarded over the control port.
*
* @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
* We recommend using nested, driver-specific attributes within this.
@@ -1926,10 +1985,10 @@ enum nl80211_commands {
* bit. Depending on which antennas are selected in the bitmap, 802.11n
* drivers can derive which chainmasks to use (if all antennas belonging to
* a particular chain are disabled this chain should be disabled) and if
- * a chain has diversity antennas wether diversity should be used or not.
+ * a chain has diversity antennas whether diversity should be used or not.
* HT capabilities (STBC, TX Beamforming, Antenna selection) can be
* derived from the available chains after applying the antenna mask.
- * Non-802.11n drivers can derive wether to use diversity or not.
+ * Non-802.11n drivers can derive whether to use diversity or not.
* Drivers may reject configurations or RX/TX mask combinations they cannot
* support by returning -EINVAL.
*
@@ -2499,7 +2558,7 @@ enum nl80211_commands {
* from successful FILS authentication and is used with
* %NL80211_CMD_CONNECT.
*
- * @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertized by a FILS AP
+ * @NL80211_ATTR_FILS_CACHE_ID: A 2-octet identifier advertised by a FILS AP
* identifying the scope of PMKSAs. This is used with
* @NL80211_CMD_SET_PMKSA and @NL80211_CMD_DEL_PMKSA.
*
@@ -2653,11 +2712,13 @@ enum nl80211_commands {
*
* @NL80211_ATTR_FILS_DISCOVERY: Optional parameter to configure FILS
* discovery. It is a nested attribute, see
- * &enum nl80211_fils_discovery_attributes.
+ * &enum nl80211_fils_discovery_attributes. Userspace should pass an empty
+ * nested attribute to disable this feature and delete the templates.
*
* @NL80211_ATTR_UNSOL_BCAST_PROBE_RESP: Optional parameter to configure
* unsolicited broadcast probe response. It is a nested attribute, see
- * &enum nl80211_unsol_bcast_probe_resp_attributes.
+ * &enum nl80211_unsol_bcast_probe_resp_attributes. Userspace should pass an empty
+ * nested attribute to disable this feature and delete the templates.
*
* @NL80211_ATTR_S1G_CAPABILITY: S1G Capability information element (from
* association request when used with NL80211_CMD_NEW_STATION)
@@ -2751,6 +2812,50 @@ enum nl80211_commands {
* the incoming frame RX timestamp.
* @NL80211_ATTR_TD_BITMAP: Transition Disable bitmap, for subsequent
* (re)associations.
+ *
+ * @NL80211_ATTR_PUNCT_BITMAP: (u32) Preamble puncturing bitmap, lowest
+ * bit corresponds to the lowest 20 MHz channel. Each bit set to 1
+ * indicates that the sub-channel is punctured. Higher 16 bits are
+ * reserved.
+ *
+ * @NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS: Maximum number of peers that HW
+ * timestamping can be enabled for concurrently (u16), a wiphy attribute.
+ * A value of 0xffff indicates setting for all peers (i.e. not specifying
+ * an address with %NL80211_CMD_SET_HW_TIMESTAMP) is supported.
+ * @NL80211_ATTR_HW_TIMESTAMP_ENABLED: Indicates whether HW timestamping should
+ * be enabled or not (flag attribute).
+ *
+ * @NL80211_ATTR_EMA_RNR_ELEMS: Optional nested attribute for
+ * reduced neighbor report (RNR) elements. This attribute can be used
+ * only when NL80211_MBSSID_CONFIG_ATTR_EMA is enabled.
+ * Userspace is responsible for splitting the RNR into multiple
+ * elements such that each element excludes the non-transmitting
+ * profiles already included in the MBSSID element
+ * (%NL80211_ATTR_MBSSID_ELEMS) at the same index. Each EMA beacon
+ * will be generated by adding MBSSID and RNR elements at the same
+ * index. If the userspace includes more RNR elements than number of
+ * MBSSID elements then these will be added in every EMA beacon.
+ *
+ * @NL80211_ATTR_MLO_LINK_DISABLED: Flag attribute indicating that the link is
+ * disabled.
+ *
+ * @NL80211_ATTR_BSS_DUMP_INCLUDE_USE_DATA: Include BSS usage data, i.e.
+ * include BSSes that can only be used in restricted scenarios and/or
+ * cannot be used at all.
+ *
+ * @NL80211_ATTR_MLO_TTLM_DLINK: Binary attribute specifying the downlink TID to
+ * link mapping. The length is 8 * sizeof(u16). For each TID the link
+ * mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element)
+ * in Draft P802.11be_D4.0.
+ * @NL80211_ATTR_MLO_TTLM_ULINK: Binary attribute specifying the uplink TID to
+ * link mapping. The length is 8 * sizeof(u16). For each TID the link
+ * mapping is as defined in section 9.4.2.314 (TID-To-Link Mapping element)
+ * in Draft P802.11be_D4.0.
+ *
+ * @NL80211_ATTR_ASSOC_SPP_AMSDU: flag attribute used with
+ * %NL80211_CMD_ASSOCIATE indicating the SPP A-MSDUs
+ * are used on this connection
+ *
* @NUM_NL80211_ATTR: total number of nl80211_attrs available
* @NL80211_ATTR_MAX: highest attribute number currently defined
* @__NL80211_ATTR_AFTER_LAST: internal use
@@ -3280,6 +3385,22 @@ enum nl80211_attrs {
NL80211_ATTR_RX_HW_TIMESTAMP,
NL80211_ATTR_TD_BITMAP,
+ NL80211_ATTR_PUNCT_BITMAP,
+
+ NL80211_ATTR_MAX_HW_TIMESTAMP_PEERS,
+ NL80211_ATTR_HW_TIMESTAMP_ENABLED,
+
+ NL80211_ATTR_EMA_RNR_ELEMS,
+
+ NL80211_ATTR_MLO_LINK_DISABLED,
+
+ NL80211_ATTR_BSS_DUMP_INCLUDE_USE_DATA,
+
+ NL80211_ATTR_MLO_TTLM_DLINK,
+ NL80211_ATTR_MLO_TTLM_ULINK,
+
+ NL80211_ATTR_ASSOC_SPP_AMSDU,
+
/* add attributes here, update the policy in nl80211.c */
__NL80211_ATTR_AFTER_LAST,
@@ -3420,6 +3541,7 @@ enum nl80211_iftype {
* @NL80211_STA_FLAG_ASSOCIATED: station is associated; used with drivers
* that support %NL80211_FEATURE_FULL_AP_CLIENT_STATE to transition a
* previously added station into associated state
+ * @NL80211_STA_FLAG_SPP_AMSDU: station supports SPP A-MSDUs
* @NL80211_STA_FLAG_MAX: highest station flag number currently defined
* @__NL80211_STA_FLAG_AFTER_LAST: internal use
*/
@@ -3432,6 +3554,7 @@ enum nl80211_sta_flags {
NL80211_STA_FLAG_AUTHENTICATED,
NL80211_STA_FLAG_TDLS_PEER,
NL80211_STA_FLAG_ASSOCIATED,
+ NL80211_STA_FLAG_SPP_AMSDU,
/* keep last */
__NL80211_STA_FLAG_AFTER_LAST,
@@ -3606,6 +3729,13 @@ enum nl80211_eht_ru_alloc {
* (u8, see &enum nl80211_eht_gi)
* @NL80211_RATE_INFO_EHT_RU_ALLOC: EHT RU allocation, if not present then
* non-OFDMA was used (u8, see &enum nl80211_eht_ru_alloc)
+ * @NL80211_RATE_INFO_S1G_MCS: S1G MCS index (u8, 0-10)
+ * @NL80211_RATE_INFO_S1G_NSS: S1G NSS value (u8, 1-4)
+ * @NL80211_RATE_INFO_1_MHZ_WIDTH: 1 MHz S1G rate
+ * @NL80211_RATE_INFO_2_MHZ_WIDTH: 2 MHz S1G rate
+ * @NL80211_RATE_INFO_4_MHZ_WIDTH: 4 MHz S1G rate
+ * @NL80211_RATE_INFO_8_MHZ_WIDTH: 8 MHz S1G rate
+ * @NL80211_RATE_INFO_16_MHZ_WIDTH: 16 MHz S1G rate
* @__NL80211_RATE_INFO_AFTER_LAST: internal use
*/
enum nl80211_rate_info {
@@ -3632,6 +3762,13 @@ enum nl80211_rate_info {
NL80211_RATE_INFO_EHT_NSS,
NL80211_RATE_INFO_EHT_GI,
NL80211_RATE_INFO_EHT_RU_ALLOC,
+ NL80211_RATE_INFO_S1G_MCS,
+ NL80211_RATE_INFO_S1G_NSS,
+ NL80211_RATE_INFO_1_MHZ_WIDTH,
+ NL80211_RATE_INFO_2_MHZ_WIDTH,
+ NL80211_RATE_INFO_4_MHZ_WIDTH,
+ NL80211_RATE_INFO_8_MHZ_WIDTH,
+ NL80211_RATE_INFO_16_MHZ_WIDTH,
/* keep last */
__NL80211_RATE_INFO_AFTER_LAST,
@@ -4000,6 +4137,10 @@ enum nl80211_band_iftype_attr {
* @NL80211_BAND_ATTR_EDMG_BW_CONFIG: Channel BW Configuration subfield encodes
* the allowed channel bandwidth configurations.
* Defined by IEEE P802.11ay/D4.0 section 9.4.2.251, Table 13.
+ * @NL80211_BAND_ATTR_S1G_MCS_NSS_SET: S1G capabilities, supported S1G-MCS and NSS
+ * set subfield, as in the S1G information IE, 5 bytes
+ * @NL80211_BAND_ATTR_S1G_CAPA: S1G capabilities information subfield as in the
+ * S1G information IE, 10 bytes
* @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
* @__NL80211_BAND_ATTR_AFTER_LAST: internal use
*/
@@ -4020,6 +4161,9 @@ enum nl80211_band_attr {
NL80211_BAND_ATTR_EDMG_CHANNELS,
NL80211_BAND_ATTR_EDMG_BW_CONFIG,
+ NL80211_BAND_ATTR_S1G_MCS_NSS_SET,
+ NL80211_BAND_ATTR_S1G_CAPA,
+
/* keep last */
__NL80211_BAND_ATTR_AFTER_LAST,
NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1
@@ -4065,7 +4209,7 @@ enum nl80211_wmm_rule {
* (100 * dBm).
* @NL80211_FREQUENCY_ATTR_DFS_STATE: current state for DFS
* (enum nl80211_dfs_state)
- * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in miliseconds for how long
+ * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in milliseconds for how long
* this channel is in this DFS state.
* @NL80211_FREQUENCY_ATTR_NO_HT40_MINUS: HT40- isn't possible with this
* channel as the control channel
@@ -4119,6 +4263,19 @@ enum nl80211_wmm_rule {
* as the primary or any of the secondary channels isn't possible
* @NL80211_FREQUENCY_ATTR_NO_EHT: EHT operation is not allowed on this channel
* in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_PSD: Power spectral density (in dBm) that
+ * is allowed on this channel in current regulatory domain.
+ * @NL80211_FREQUENCY_ATTR_DFS_CONCURRENT: Operation on this channel is
+ * allowed for peer-to-peer or adhoc communication under the control
+ * of a DFS master which operates on the same channel (FCC-594280 D01
+ * Section B.3). Should be used together with %NL80211_RRF_DFS only.
+ * @NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT: Client connection to VLP AP
+ * not allowed using this channel
+ * @NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT: Client connection to AFC AP
+ * not allowed using this channel
+ * @NL80211_FREQUENCY_ATTR_CAN_MONITOR: This channel can be used in monitor
+ * mode despite other (regulatory) restrictions, even if the channel is
+ * otherwise completely disabled.
* @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
* currently defined
* @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
@@ -4157,6 +4314,11 @@ enum nl80211_frequency_attr {
NL80211_FREQUENCY_ATTR_16MHZ,
NL80211_FREQUENCY_ATTR_NO_320MHZ,
NL80211_FREQUENCY_ATTR_NO_EHT,
+ NL80211_FREQUENCY_ATTR_PSD,
+ NL80211_FREQUENCY_ATTR_DFS_CONCURRENT,
+ NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT,
+ NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT,
+ NL80211_FREQUENCY_ATTR_CAN_MONITOR,
/* keep last */
__NL80211_FREQUENCY_ATTR_AFTER_LAST,
@@ -4169,6 +4331,10 @@ enum nl80211_frequency_attr {
#define NL80211_FREQUENCY_ATTR_NO_IR NL80211_FREQUENCY_ATTR_NO_IR
#define NL80211_FREQUENCY_ATTR_GO_CONCURRENT \
NL80211_FREQUENCY_ATTR_IR_CONCURRENT
+#define NL80211_FREQUENCY_ATTR_NO_UHB_VLP_CLIENT \
+ NL80211_FREQUENCY_ATTR_NO_6GHZ_VLP_CLIENT
+#define NL80211_FREQUENCY_ATTR_NO_UHB_AFC_CLIENT \
+ NL80211_FREQUENCY_ATTR_NO_6GHZ_AFC_CLIENT
/**
* enum nl80211_bitrate_attr - bitrate attributes
@@ -4257,6 +4423,8 @@ enum nl80211_reg_type {
* a given frequency range. The value is in mBm (100 * dBm).
* @NL80211_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
* If not present or 0 default CAC time will be used.
+ * @NL80211_ATTR_POWER_RULE_PSD: power spectral density (in dBm).
+ * This could be negative.
* @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
* currently defined
* @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use
@@ -4274,6 +4442,8 @@ enum nl80211_reg_rule_attr {
NL80211_ATTR_DFS_CAC_TIME,
+ NL80211_ATTR_POWER_RULE_PSD,
+
/* keep last */
__NL80211_REG_RULE_ATTR_AFTER_LAST,
NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1
@@ -4302,14 +4472,7 @@ enum nl80211_reg_rule_attr {
* value as specified by &struct nl80211_bss_select_rssi_adjust.
* @NL80211_SCHED_SCAN_MATCH_ATTR_BSSID: BSSID to be used for matching
* (this cannot be used together with SSID).
- * @NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI: Nested attribute that carries the
- * band specific minimum rssi thresholds for the bands defined in
- * enum nl80211_band. The minimum rssi threshold value(s32) specific to a
- * band shall be encapsulated in attribute with type value equals to one
- * of the NL80211_BAND_* defined in enum nl80211_band. For example, the
- * minimum rssi threshold value for 2.4GHZ band shall be encapsulated
- * within an attribute of type NL80211_BAND_2GHZ. And one or more of such
- * attributes will be nested within this attribute.
+ * @NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI: Obsolete
* @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter
* attribute number currently defined
* @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use
@@ -4322,7 +4485,7 @@ enum nl80211_sched_scan_match_attr {
NL80211_SCHED_SCAN_MATCH_ATTR_RELATIVE_RSSI,
NL80211_SCHED_SCAN_MATCH_ATTR_RSSI_ADJUST,
NL80211_SCHED_SCAN_MATCH_ATTR_BSSID,
- NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI,
+ NL80211_SCHED_SCAN_MATCH_PER_BAND_RSSI, /* obsolete */
/* keep last */
__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST,
@@ -4356,6 +4519,14 @@ enum nl80211_sched_scan_match_attr {
* @NL80211_RRF_NO_160MHZ: 160MHz operation not allowed
* @NL80211_RRF_NO_HE: HE operation not allowed
* @NL80211_RRF_NO_320MHZ: 320MHz operation not allowed
+ * @NL80211_RRF_NO_EHT: EHT operation not allowed
+ * @NL80211_RRF_PSD: Ruleset has power spectral density value
+ * @NL80211_RRF_DFS_CONCURRENT: Operation on this channel is allowed for
+ peer-to-peer or adhoc communication under the control of a DFS master
+ which operates on the same channel (FCC-594280 D01 Section B.3).
+ Should be used together with %NL80211_RRF_DFS only.
+ * @NL80211_RRF_NO_6GHZ_VLP_CLIENT: Client connection to VLP AP not allowed
+ * @NL80211_RRF_NO_6GHZ_AFC_CLIENT: Client connection to AFC AP not allowed
*/
enum nl80211_reg_rule_flags {
NL80211_RRF_NO_OFDM = 1<<0,
@@ -4375,6 +4546,11 @@ enum nl80211_reg_rule_flags {
NL80211_RRF_NO_160MHZ = 1<<16,
NL80211_RRF_NO_HE = 1<<17,
NL80211_RRF_NO_320MHZ = 1<<18,
+ NL80211_RRF_NO_EHT = 1<<19,
+ NL80211_RRF_PSD = 1<<20,
+ NL80211_RRF_DFS_CONCURRENT = 1<<21,
+ NL80211_RRF_NO_6GHZ_VLP_CLIENT = 1<<22,
+ NL80211_RRF_NO_6GHZ_AFC_CLIENT = 1<<23,
};
#define NL80211_RRF_PASSIVE_SCAN NL80211_RRF_NO_IR
@@ -4383,6 +4559,8 @@ enum nl80211_reg_rule_flags {
#define NL80211_RRF_NO_HT40 (NL80211_RRF_NO_HT40MINUS |\
NL80211_RRF_NO_HT40PLUS)
#define NL80211_RRF_GO_CONCURRENT NL80211_RRF_IR_CONCURRENT
+#define NL80211_RRF_NO_UHB_VLP_CLIENT NL80211_RRF_NO_6GHZ_VLP_CLIENT
+#define NL80211_RRF_NO_UHB_AFC_CLIENT NL80211_RRF_NO_6GHZ_AFC_CLIENT
/* For backport compatibility with older userspace */
#define NL80211_RRF_NO_IR_ALL (NL80211_RRF_NO_IR | __NL80211_RRF_NO_IBSS)
@@ -4912,6 +5090,36 @@ enum nl80211_bss_scan_width {
};
/**
+ * enum nl80211_bss_use_for - bitmap indicating possible BSS use
+ * @NL80211_BSS_USE_FOR_NORMAL: Use this BSS for normal "connection",
+ * including IBSS/MBSS depending on the type.
+ * @NL80211_BSS_USE_FOR_MLD_LINK: This BSS can be used as a link in an
+ * MLO connection. Note that for an MLO connection, all links including
+ * the assoc link must have this flag set, and the assoc link must
+ * additionally have %NL80211_BSS_USE_FOR_NORMAL set.
+ */
+enum nl80211_bss_use_for {
+ NL80211_BSS_USE_FOR_NORMAL = 1 << 0,
+ NL80211_BSS_USE_FOR_MLD_LINK = 1 << 1,
+};
+
+/**
+ * enum nl80211_bss_cannot_use_reasons - reason(s) connection to a
+ * BSS isn't possible
+ * @NL80211_BSS_CANNOT_USE_NSTR_NONPRIMARY: NSTR nonprimary links aren't
+ * supported by the device, and this BSS entry represents one.
+ * @NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH: STA is not supporting
+ * the AP power type (SP, VLP, AP) that the AP uses.
+ */
+enum nl80211_bss_cannot_use_reasons {
+ NL80211_BSS_CANNOT_USE_NSTR_NONPRIMARY = 1 << 0,
+ NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH = 1 << 1,
+};
+
+#define NL80211_BSS_CANNOT_USE_UHB_PWR_MISMATCH \
+ NL80211_BSS_CANNOT_USE_6GHZ_PWR_MISMATCH
+
+/**
* enum nl80211_bss - netlink attributes for a BSS
*
* @__NL80211_BSS_INVALID: invalid
@@ -4942,7 +5150,7 @@ enum nl80211_bss_scan_width {
* elements from a Beacon frame (bin); not present if no Beacon frame has
* yet been received
* @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
- * (u32, enum nl80211_bss_scan_width)
+ * (u32, enum nl80211_bss_scan_width) - No longer used!
* @NL80211_BSS_BEACON_TSF: TSF of the last received beacon (u64)
* (not present if no beacon frame has been received yet)
* @NL80211_BSS_PRESP_DATA: the data in @NL80211_BSS_INFORMATION_ELEMENTS and
@@ -4963,6 +5171,14 @@ enum nl80211_bss_scan_width {
* @NL80211_BSS_FREQUENCY_OFFSET: frequency offset in KHz
* @NL80211_BSS_MLO_LINK_ID: MLO link ID of the BSS (u8).
* @NL80211_BSS_MLD_ADDR: MLD address of this BSS if connected to it.
+ * @NL80211_BSS_USE_FOR: u32 bitmap attribute indicating what the BSS can be
+ * used for, see &enum nl80211_bss_use_for.
+ * @NL80211_BSS_CANNOT_USE_REASONS: Indicates the reason that this BSS cannot
+ * be used for all or some of the possible uses by the device reporting it,
+ * even though its presence was detected.
+ * This is a u64 attribute containing a bitmap of values from
+ * &enum nl80211_cannot_use_reasons, note that the attribute may be missing
+ * if no reasons are specified.
* @__NL80211_BSS_AFTER_LAST: internal
* @NL80211_BSS_MAX: highest BSS attribute
*/
@@ -4990,6 +5206,8 @@ enum nl80211_bss {
NL80211_BSS_FREQUENCY_OFFSET,
NL80211_BSS_MLO_LINK_ID,
NL80211_BSS_MLD_ADDR,
+ NL80211_BSS_USE_FOR,
+ NL80211_BSS_CANNOT_USE_REASONS,
/* keep last */
__NL80211_BSS_AFTER_LAST,
@@ -5338,7 +5556,7 @@ enum nl80211_tx_rate_setting {
* (%NL80211_TID_CONFIG_ATTR_TIDS, %NL80211_TID_CONFIG_ATTR_OVERRIDE).
* @NL80211_TID_CONFIG_ATTR_PEER_SUPP: same as the previous per-vif one, but
* per peer instead.
- * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribue, if set indicates
+ * @NL80211_TID_CONFIG_ATTR_OVERRIDE: flag attribute, if set indicates
* that the new configuration overrides all previous peer
* configurations, otherwise previous peer specific configurations
* should be left untouched.
@@ -5539,6 +5757,8 @@ struct nl80211_pattern_support {
* %NL80211_ATTR_SCAN_FREQUENCIES contains more than one
* frequency, it means that the match occurred in more than one
* channel.
+ * @NL80211_WOWLAN_TRIG_UNPROTECTED_DEAUTH_DISASSOC: For wakeup reporting only.
+ * Wake up happened due to unprotected deauth or disassoc frame in MFP.
* @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers
* @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number
*
@@ -5566,6 +5786,7 @@ enum nl80211_wowlan_triggers {
NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS,
NL80211_WOWLAN_TRIG_NET_DETECT,
NL80211_WOWLAN_TRIG_NET_DETECT_RESULTS,
+ NL80211_WOWLAN_TRIG_UNPROTECTED_DEAUTH_DISASSOC,
/* keep last */
NUM_NL80211_WOWLAN_TRIG,
@@ -5721,7 +5942,7 @@ enum nl80211_attr_coalesce_rule {
/**
* enum nl80211_coalesce_condition - coalesce rule conditions
- * @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns
+ * @NL80211_COALESCE_CONDITION_MATCH: coalesce Rx packets when patterns
* in a rule are matched.
* @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns
* in a rule are not matched.
@@ -5820,7 +6041,7 @@ enum nl80211_if_combination_attrs {
* enum nl80211_plink_state - state of a mesh peer link finite state machine
*
* @NL80211_PLINK_LISTEN: initial state, considered the implicit
- * state of non existent mesh peer links
+ * state of non-existent mesh peer links
* @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to
* this mesh peer
* @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received
@@ -5869,6 +6090,7 @@ enum plink_actions {
#define NL80211_KEK_LEN 16
#define NL80211_KCK_EXT_LEN 24
#define NL80211_KEK_EXT_LEN 32
+#define NL80211_KCK_EXT_LEN_32 32
#define NL80211_REPLAY_CTR_LEN 8
/**
@@ -6112,7 +6334,7 @@ enum nl80211_feature_flags {
* request to use RRM (see %NL80211_ATTR_USE_RRM) with
* %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests, which will set
* the ASSOC_REQ_USE_RRM flag in the association request even if
- * NL80211_FEATURE_QUIET is not advertized.
+ * NL80211_FEATURE_QUIET is not advertised.
* @NL80211_EXT_FEATURE_MU_MIMO_AIR_SNIFFER: This device supports MU-MIMO air
* sniffer which means that it can be configured to hear packets from
* certain groups which can be configured by the
@@ -6124,13 +6346,15 @@ enum nl80211_feature_flags {
* the BSS that the interface that requested the scan is connected to
* (if available).
* @NL80211_EXT_FEATURE_BSS_PARENT_TSF: Per BSS, this driver reports the
- * time the last beacon/probe was received. The time is the TSF of the
- * BSS that the interface that requested the scan is connected to
- * (if available).
+ * time the last beacon/probe was received. For a non-MLO connection, the
+ * time is the TSF of the BSS that the interface that requested the scan is
+ * connected to (if available). For an MLO connection, the time is the TSF
+ * of the BSS corresponding with link ID specified in the scan request (if
+ * specified).
* @NL80211_EXT_FEATURE_SET_SCAN_DWELL: This driver supports configuration of
* channel dwell time.
* @NL80211_EXT_FEATURE_BEACON_RATE_LEGACY: Driver supports beacon rate
- * configuration (AP/mesh), supporting a legacy (non HT/VHT) rate.
+ * configuration (AP/mesh), supporting a legacy (non-HT/VHT) rate.
* @NL80211_EXT_FEATURE_BEACON_RATE_HT: Driver supports beacon rate
* configuration (AP/mesh) with HT rates.
* @NL80211_EXT_FEATURE_BEACON_RATE_VHT: Driver supports beacon rate
@@ -6204,8 +6428,7 @@ enum nl80211_feature_flags {
* @NL80211_EXT_FEATURE_AP_PMKSA_CACHING: Driver/device supports PMKSA caching
* (set/del PMKSA operations) in AP mode.
*
- * @NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD: Driver supports
- * filtering of sched scan results using band specific RSSI thresholds.
+ * @NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD: Obsolete
*
* @NL80211_EXT_FEATURE_STA_TX_PWR: This driver supports controlling tx power
* to a station.
@@ -6294,6 +6517,31 @@ enum nl80211_feature_flags {
* might apply, e.g. no scans in progress, no offchannel operations
* in progress, and no active connections.
*
+ * @NL80211_EXT_FEATURE_PUNCT: Driver supports preamble puncturing in AP mode.
+ *
+ * @NL80211_EXT_FEATURE_SECURE_NAN: Device supports NAN Pairing which enables
+ * authentication, data encryption and message integrity.
+ *
+ * @NL80211_EXT_FEATURE_AUTH_AND_DEAUTH_RANDOM_TA: Device supports randomized TA
+ * in authentication and deauthentication frames sent to unassociated peer
+ * using @NL80211_CMD_FRAME.
+ *
+ * @NL80211_EXT_FEATURE_OWE_OFFLOAD: Driver/Device wants to do OWE DH IE
+ * handling in station mode.
+ *
+ * @NL80211_EXT_FEATURE_OWE_OFFLOAD_AP: Driver/Device wants to do OWE DH IE
+ * handling in AP mode.
+ *
+ * @NL80211_EXT_FEATURE_DFS_CONCURRENT: The device supports peer-to-peer or
+ * ad hoc operation on DFS channels under the control of a concurrent
+ * DFS master on the same channel as described in FCC-594280 D01
+ * (Section B.3). This, for example, allows P2P GO and P2P clients to
+ * operate on DFS channels as long as there's a concurrent BSS connection.
+ *
+ * @NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT: The driver has support for SPP
+ * (signaling and payload protected) A-MSDUs and this shall be advertised
+ * in the RSNXE.
+ *
* @NUM_NL80211_EXT_FEATURES: number of extended features.
* @MAX_NL80211_EXT_FEATURES: highest extended feature index.
*/
@@ -6335,7 +6583,7 @@ enum nl80211_ext_feature_index {
NL80211_EXT_FEATURE_ENABLE_FTM_RESPONDER,
NL80211_EXT_FEATURE_AIRTIME_FAIRNESS,
NL80211_EXT_FEATURE_AP_PMKSA_CACHING,
- NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD,
+ NL80211_EXT_FEATURE_SCHED_SCAN_BAND_SPECIFIC_RSSI_THOLD, /* obsolete */
NL80211_EXT_FEATURE_EXT_KEY_ID,
NL80211_EXT_FEATURE_STA_TX_PWR,
NL80211_EXT_FEATURE_SAE_OFFLOAD,
@@ -6362,6 +6610,13 @@ enum nl80211_ext_feature_index {
NL80211_EXT_FEATURE_FILS_CRYPTO_OFFLOAD,
NL80211_EXT_FEATURE_RADAR_BACKGROUND,
NL80211_EXT_FEATURE_POWERED_ADDR_CHANGE,
+ NL80211_EXT_FEATURE_PUNCT,
+ NL80211_EXT_FEATURE_SECURE_NAN,
+ NL80211_EXT_FEATURE_AUTH_AND_DEAUTH_RANDOM_TA,
+ NL80211_EXT_FEATURE_OWE_OFFLOAD,
+ NL80211_EXT_FEATURE_OWE_OFFLOAD_AP,
+ NL80211_EXT_FEATURE_DFS_CONCURRENT,
+ NL80211_EXT_FEATURE_SPP_AMSDU_SUPPORT,
/* add new features before the definition below */
NUM_NL80211_EXT_FEATURES,
@@ -6446,7 +6701,7 @@ enum nl80211_timeout_reason {
* request parameters IE in the probe request
* @NL80211_SCAN_FLAG_ACCEPT_BCAST_PROBE_RESP: accept broadcast probe responses
* @NL80211_SCAN_FLAG_OCE_PROBE_REQ_HIGH_TX_RATE: send probe request frames at
- * rate of at least 5.5M. In case non OCE AP is discovered in the channel,
+ * rate of at least 5.5M. In case non-OCE AP is discovered in the channel,
* only the first probe req in the channel will be sent in high rate.
* @NL80211_SCAN_FLAG_OCE_PROBE_REQ_DEFERRAL_SUPPRESSION: allow probe request
* tx deferral (dot11FILSProbeDelay shall be set to 15ms)
@@ -6476,8 +6731,16 @@ enum nl80211_timeout_reason {
* @NL80211_SCAN_FLAG_FREQ_KHZ: report scan results with
* %NL80211_ATTR_SCAN_FREQ_KHZ. This also means
* %NL80211_ATTR_SCAN_FREQUENCIES will not be included.
- * @NL80211_SCAN_FLAG_COLOCATED_6GHZ: scan for colocated APs reported by
- * 2.4/5 GHz APs
+ * @NL80211_SCAN_FLAG_COLOCATED_6GHZ: scan for collocated APs reported by
+ * 2.4/5 GHz APs. When the flag is set, the scan logic will use the
+ * information from the RNR element found in beacons/probe responses
+ * received on the 2.4/5 GHz channels to actively scan only the 6GHz
+ * channels on which APs are expected to be found. Note that when not set,
+ * the scan logic would scan all 6GHz channels, but since transmission of
+ * probe requests on non-PSC channels is limited, it is highly likely that
+ * these channels would passively be scanned. Also note that when the flag
+ * is set, in addition to the colocated APs, PSC channels would also be
+ * scanned if the user space has asked for it.
*/
enum nl80211_scan_flags {
NL80211_SCAN_FLAG_LOW_PRIORITY = 1<<0,
@@ -6806,7 +7069,7 @@ enum nl80211_nan_func_term_reason {
* The instance ID for the follow up Service Discovery Frame. This is u8.
* @NL80211_NAN_FUNC_FOLLOW_UP_REQ_ID: relevant if the function's type
* is follow up. This is a u8.
- * The requestor instance ID for the follow up Service Discovery Frame.
+ * The requester instance ID for the follow up Service Discovery Frame.
* @NL80211_NAN_FUNC_FOLLOW_UP_DEST: the MAC address of the recipient of the
* follow up Service Discovery Frame. This is a binary attribute.
* @NL80211_NAN_FUNC_CLOSE_RANGE: is this function limited for devices in a
@@ -7196,7 +7459,7 @@ enum nl80211_peer_measurement_attrs {
* @NL80211_PMSR_FTM_CAPA_ATTR_TRIGGER_BASED: flag attribute indicating if
* trigger based ranging measurement is supported
* @NL80211_PMSR_FTM_CAPA_ATTR_NON_TRIGGER_BASED: flag attribute indicating
- * if non trigger based ranging measurement is supported
+ * if non-trigger-based ranging measurement is supported
*
* @NUM_NL80211_PMSR_FTM_CAPA_ATTR: internal
* @NL80211_PMSR_FTM_CAPA_ATTR_MAX: highest attribute number
@@ -7250,7 +7513,7 @@ enum nl80211_peer_measurement_ftm_capa {
* if neither %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED nor
* %NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED is set, EDCA based
* ranging will be used.
- * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non trigger based
+ * @NL80211_PMSR_FTM_REQ_ATTR_NON_TRIGGER_BASED: request non-trigger-based
* ranging measurement (flag)
* This attribute and %NL80211_PMSR_FTM_REQ_ATTR_TRIGGER_BASED are
* mutually exclusive.
@@ -7328,7 +7591,7 @@ enum nl80211_peer_measurement_ftm_failure_reasons {
* @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_ATTEMPTS: number of FTM Request frames
* transmitted (u32, optional)
* @NL80211_PMSR_FTM_RESP_ATTR_NUM_FTMR_SUCCESSES: number of FTM Request frames
- * that were acknowleged (u32, optional)
+ * that were acknowledged (u32, optional)
* @NL80211_PMSR_FTM_RESP_ATTR_BUSY_RETRY_TIME: retry time received from the
* busy peer (u32, seconds)
* @NL80211_PMSR_FTM_RESP_ATTR_NUM_BURSTS_EXP: actual number of bursts exponent
@@ -7489,7 +7752,7 @@ enum nl80211_iftype_akm_attributes {
* @NL80211_FILS_DISCOVERY_ATTR_INT_MIN: Minimum packet interval (u32, TU).
* Allowed range: 0..10000 (TU = Time Unit)
* @NL80211_FILS_DISCOVERY_ATTR_INT_MAX: Maximum packet interval (u32, TU).
- * Allowed range: 0..10000 (TU = Time Unit)
+ * Allowed range: 0..10000 (TU = Time Unit). If set to 0, the feature is disabled.
* @NL80211_FILS_DISCOVERY_ATTR_TMPL: Template data for FILS discovery action
* frame including the headers.
*
@@ -7522,7 +7785,8 @@ enum nl80211_fils_discovery_attributes {
*
* @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_INT: Maximum packet interval (u32, TU).
* Allowed range: 0..20 (TU = Time Unit). IEEE P802.11ax/D6.0
- * 26.17.2.3.2 (AP behavior for fast passive scanning).
+ * 26.17.2.3.2 (AP behavior for fast passive scanning). If set to 0, the feature is
+ * disabled.
* @NL80211_UNSOL_BCAST_PROBE_RESP_ATTR_TMPL: Unsolicited broadcast probe response
* frame template (binary).
*