1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
/* packet-ieee8023.c
* Routine for dissecting Ethernet packets with a length field (as opposed
* to a type field).
*
* The name "ieee8023" is historical, dating back to when IEEE Std 802.3
* had only a length field and expected all packets to have an 802.2
* header following the MAC header. Since IEEE 802.3y-1997, 802.3
* supports either a type field or a length field, so it's no longer
* correct to refer to "802.3" vs. "D/I/X" or vs. "Ethernet II" frames.
*
* Wireshark - Network traffic analyzer
* By Gerald Combs <gerald@wireshark.org>
* Copyright 1998 Gerald Combs
*
* SPDX-License-Identifier: GPL-2.0-or-later
*/
#include "config.h"
#include <epan/packet.h>
#include <epan/exceptions.h>
#include <epan/expert.h>
#include <epan/show_exception.h>
#include "packet-ieee8023.h"
#include "packet-eth.h"
void proto_reg_handoff_ieee802_3(void);
static dissector_handle_t ipx_handle;
static dissector_handle_t llc_handle;
static dissector_handle_t ccsds_handle;
void
dissect_802_3(volatile int length, gboolean is_802_2, tvbuff_t *tvb,
int offset_after_length, packet_info *pinfo, proto_tree *tree,
proto_tree *fh_tree, int length_id, int trailer_id, expert_field* ei_len,
int fcs_len)
{
proto_item *length_it;
tvbuff_t *volatile next_tvb = NULL;
tvbuff_t *trailer_tvb = NULL;
const char *saved_proto;
gint captured_length, reported_length;
length_it = proto_tree_add_uint(fh_tree, length_id, tvb,
offset_after_length - 2, 2, length);
/* Get the length of the payload.
If the FCS length is positive, remove the FCS.
(If it's zero, there's no FCS; if it's negative, we don't know whether
there's an FCS, so we'll guess based on the length of the trailer.) */
reported_length = tvb_reported_length_remaining(tvb, offset_after_length);
if (fcs_len > 0) {
if (reported_length >= fcs_len)
reported_length -= fcs_len;
}
/* Make sure the length in the 802.3 header doesn't go past the end of
the payload. */
if (length > reported_length) {
length = reported_length;
expert_add_info(pinfo, length_it, ei_len);
}
/* Give the next dissector only 'length' number of bytes. */
captured_length = tvb_captured_length_remaining(tvb, offset_after_length);
if (captured_length > length)
captured_length = length;
next_tvb = tvb_new_subset_length_caplen(tvb, offset_after_length, captured_length, length);
/* Dissect the payload either as IPX or as an LLC frame.
Catch non-fatal exceptions, so that if the reported length
of "next_tvb" was reduced by some dissector before an
exception was thrown, we can still put in an item for
the trailer. */
saved_proto = pinfo->current_proto;
TRY {
if (is_802_2)
call_dissector(llc_handle, next_tvb, pinfo, tree);
else {
/* Check if first three bits of payload are 0x7.
If so, then payload is IPX. If not, then it's CCSDS.
Refer to packet-eth.c for setting of is_802_2 variable. */
if (tvb_get_bits8(next_tvb, 0, 3) == 7)
call_dissector(ipx_handle, next_tvb, pinfo, tree);
else
call_dissector(ccsds_handle, next_tvb, pinfo, tree);
}
}
CATCH_NONFATAL_ERRORS {
/* Somebody threw an exception that means that there was a problem
dissecting the payload; that means that a dissector was found,
so we don't need to dissect the payload as data or update the
protocol or info columns.
Just show the exception and then drive on to show the trailer,
after noting that a dissector was found and restoring the
protocol value that was in effect before we called the subdissector. */
show_exception(next_tvb, pinfo, tree, EXCEPT_CODE, GET_MESSAGE);
}
ENDTRY;
/* Restore the protocol value, so that any exception thrown by
tvb_new_subset_remaining() refers to the protocol for which
this is a trailer. */
pinfo->current_proto = saved_proto;
/* Construct a tvbuff for the trailer; if the trailer is past the
end of the captured data, this will throw a BoundsError, which
is what we want, as it'll report that the packet was cut short. */
trailer_tvb = tvb_new_subset_remaining(tvb, offset_after_length + length);
add_ethernet_trailer(pinfo, tree, fh_tree, trailer_id, tvb, trailer_tvb, fcs_len);
}
void
proto_reg_handoff_ieee802_3(void)
{
/*
* Get handles for the subdissectors.
*/
ipx_handle = find_dissector("ipx");
llc_handle = find_dissector("llc");
ccsds_handle = find_dissector("ccsds");
}
/*
* Editor modelines - https://www.wireshark.org/tools/modelines.html
*
* Local Variables:
* c-basic-offset: 2
* tab-width: 8
* indent-tabs-mode: nil
* End:
*
* ex: set shiftwidth=2 tabstop=8 expandtab:
* :indentSize=2:tabSize=8:noTabs=true:
*/
|
