Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 545 insertions, 0 deletions

diff --git a/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
new file mode 100644
index 000000000..629e604aa
--- /dev/null
+++ b/arch/arm64/boot/dts/hisilicon/hi6220-hikey.dts
@@ -0,0 +1,545 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * dts file for Hisilicon HiKey Development Board
+ *
+ * Copyright (C) 2015, HiSilicon Ltd.
+ *
+ */
+
+/dts-v1/;
+#include "hi6220.dtsi"
+#include "hikey-pinctrl.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "HiKey Development Board";
+	compatible = "hisilicon,hi6220-hikey", "hisilicon,hi6220";
+
+	aliases {
+		serial0 = &uart0; /* On board UART0 */
+		serial1 = &uart1; /* BT UART */
+		serial2 = &uart2; /* LS Expansion UART0 */
+		serial3 = &uart3; /* LS Expansion UART1 */
+	};
+
+	chosen {
+		stdout-path = "serial3:115200n8";
+	};
+
+	/*
+	 * Reserve below regions from memory node:
+	 *
+	 *  0x05e0,0000 - 0x05ef,ffff: MCU firmware runtime using
+	 *  0x05f0,1000 - 0x05f0,1fff: Reboot reason
+	 *  0x06df,f000 - 0x06df,ffff: Mailbox message data
+	 *  0x0740,f000 - 0x0740,ffff: MCU firmware section
+	 *  0x21f0,0000 - 0x21ff,ffff: pstore/ramoops buffer
+	 *  0x3e00,0000 - 0x3fff,ffff: OP-TEE
+	 */
+	memory@0 {
+		device_type = "memory";
+		reg = <0x00000000 0x00000000 0x00000000 0x05e00000>,
+		      <0x00000000 0x05f00000 0x00000000 0x00001000>,
+		      <0x00000000 0x05f02000 0x00000000 0x00efd000>,
+		      <0x00000000 0x06e00000 0x00000000 0x0060f000>,
+		      <0x00000000 0x07410000 0x00000000 0x1aaf0000>,
+		      <0x00000000 0x22000000 0x00000000 0x1c000000>;
+	};
+
+	reserved-memory {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges;
+
+		ramoops@21f00000 {
+			compatible = "ramoops";
+			reg = <0x0 0x21f00000 0x0 0x00100000>;
+			record-size = <0x00020000>;
+			console-size = <0x00020000>;
+			ftrace-size = <0x00020000>;
+		};
+
+		/* global autoconfigured region for contiguous allocations */
+		linux,cma {
+			compatible = "shared-dma-pool";
+			reusable;
+			size = <0x00000000 0x08000000>;
+			linux,cma-default;
+		};
+	};
+
+	reboot-mode-syscon@5f01000 {
+		compatible = "syscon", "simple-mfd";
+		reg = <0x0 0x05f01000 0x0 0x00001000>;
+
+		reboot-mode {
+			compatible = "syscon-reboot-mode";
+			offset = <0x0>;
+
+			mode-normal = <0x77665501>;
+			mode-bootloader = <0x77665500>;
+			mode-recovery = <0x77665502>;
+		};
+	};
+
+	reg_sys_5v: regulator@0 {
+		compatible = "regulator-fixed";
+		regulator-name = "SYS_5V";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	reg_vdd_3v3: regulator@1 {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_3V3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-boot-on;
+		regulator-always-on;
+		vin-supply = <&reg_sys_5v>;
+	};
+
+	reg_5v_hub: regulator@2 {
+		compatible = "regulator-fixed";
+		regulator-name = "5V_HUB";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		regulator-boot-on;
+		gpio = <&gpio0 7 0>;
+		regulator-always-on;
+		vin-supply = <&reg_sys_5v>;
+	};
+
+	wl1835_pwrseq: wl1835-pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		/* WLAN_EN GPIO */
+		reset-gpios = <&gpio0 5 GPIO_ACTIVE_LOW>;
+		clocks = <&pmic>;
+		clock-names = "ext_clock";
+		post-power-on-delay-ms = <10>;
+		power-off-delay-us = <10>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		user_led1 {
+			label = "green:user1";
+			gpios = <&gpio4 0 0>; /* <&gpio_user_led_1>; */
+			linux,default-trigger = "heartbeat";
+		};
+
+		user_led2 {
+			label = "green:user2";
+			gpios = <&gpio4 1 0>; /* <&gpio_user_led_2>; */
+			linux,default-trigger = "mmc0";
+		};
+
+		user_led3 {
+			label = "green:user3";
+			gpios = <&gpio4 2 0>; /* <&gpio_user_led_3>; */
+			linux,default-trigger = "mmc1";
+		};
+
+		user_led4 {
+			label = "green:user4";
+			gpios = <&gpio4 3 0>; /* <&gpio_user_led_4>; */
+			panic-indicator;
+			linux,default-trigger = "none";
+		};
+
+		wlan_active_led {
+			label = "yellow:wlan";
+			gpios = <&gpio3 5 0>; /* <&gpio_wlan_active_led>; */
+			linux,default-trigger = "phy0tx";
+			default-state = "off";
+		};
+
+		bt_active_led {
+			label = "blue:bt";
+			gpios = <&gpio4 7 0>; /* <&gpio_bt_active_led>; */
+			linux,default-trigger = "hci0-power";
+			default-state = "off";
+		};
+	};
+
+	pmic: pmic@f8000000 {
+		compatible = "hisilicon,hi655x-pmic";
+		reg = <0x0 0xf8000000 0x0 0x1000>;
+		#clock-cells = <0>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+		pmic-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+
+		regulators {
+			ldo2: LDO2 {
+				regulator-name = "LDO2_2V8";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3200000>;
+				regulator-enable-ramp-delay = <120>;
+			};
+
+			ldo7: LDO7 {
+				regulator-name = "LDO7_SDIO";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-enable-ramp-delay = <120>;
+			};
+
+			ldo10: LDO10 {
+				regulator-name = "LDO10_2V85";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-enable-ramp-delay = <360>;
+			};
+
+			ldo13: LDO13 {
+				regulator-name = "LDO13_1V8";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <1950000>;
+				regulator-enable-ramp-delay = <120>;
+			};
+
+			ldo14: LDO14 {
+				regulator-name = "LDO14_2V8";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3200000>;
+				regulator-enable-ramp-delay = <120>;
+			};
+
+			ldo15: LDO15 {
+				regulator-name = "LDO15_1V8";
+				regulator-min-microvolt = <1600000>;
+				regulator-max-microvolt = <1950000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-enable-ramp-delay = <120>;
+			};
+
+			ldo17: LDO17 {
+				regulator-name = "LDO17_2V5";
+				regulator-min-microvolt = <2500000>;
+				regulator-max-microvolt = <3200000>;
+				regulator-enable-ramp-delay = <120>;
+			};
+
+			ldo19: LDO19 {
+				regulator-name = "LDO19_3V0";
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3000000>;
+				regulator-enable-ramp-delay = <360>;
+			};
+
+			ldo21: LDO21 {
+				regulator-name = "LDO21_1V8";
+				regulator-min-microvolt = <1650000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-always-on;
+				regulator-enable-ramp-delay = <120>;
+			};
+
+			ldo22: LDO22 {
+				regulator-name = "LDO22_1V2";
+				regulator-min-microvolt = <900000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-boot-on;
+				regulator-always-on;
+				regulator-enable-ramp-delay = <120>;
+			};
+		};
+	};
+
+	firmware {
+		optee {
+			compatible = "linaro,optee-tz";
+			method = "smc";
+		};
+	};
+
+	sound_card {
+		compatible = "audio-graph-card";
+		dais = <&i2s0_port0>;
+	};
+};
+
+&uart1 {
+	assigned-clocks = <&sys_ctrl HI6220_UART1_SRC>;
+	assigned-clock-rates = <150000000>;
+	status = "okay";
+
+	bluetooth {
+		compatible = "ti,wl1835-st";
+		enable-gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
+		clocks = <&pmic>;
+		clock-names = "ext_clock";
+	};
+};
+
+&uart2 {
+	status = "okay";
+	label = "LS-UART0";
+};
+
+&uart3 {
+	status = "okay";
+	label = "LS-UART1";
+};
+
+&ade {
+	status = "okay";
+};
+
+&dsi {
+	status = "okay";
+
+	ports {
+		/* 1 for output port */
+		port@1 {
+			reg = <1>;
+
+			dsi_out0: endpoint@0 {
+				remote-endpoint = <&adv7533_in>;
+			};
+		};
+	};
+};
+
+&dwmmc_0 {
+	cap-mmc-highspeed;
+	non-removable;
+	bus-width = <0x8>;
+	vmmc-supply = <&ldo19>;
+};
+
+&dwmmc_1 {
+	card-detect-delay = <200>;
+	cap-sd-highspeed;
+	sd-uhs-sdr12;
+	sd-uhs-sdr25;
+	sd-uhs-sdr50;
+	vqmmc-supply = <&ldo7>;
+	vmmc-supply = <&ldo10>;
+	bus-width = <0x4>;
+	disable-wp;
+	cd-gpios = <&gpio1 0 1>;
+};
+
+&dwmmc_2 {
+	bus-width = <0x4>;
+	non-removable;
+	cap-power-off-card;
+	vmmc-supply = <&reg_vdd_3v3>;
+	mmc-pwrseq = <&wl1835_pwrseq>;
+
+	#address-cells = <0x1>;
+	#size-cells = <0x0>;
+	wlcore: wlcore@2 {
+		compatible = "ti,wl1835";
+		reg = <2>;	/* sdio func num */
+		/* WL_IRQ, WL_HOST_WAKE_GPIO1_3 */
+		interrupt-parent = <&gpio1>;
+		interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+	};
+};
+
+/*
+ * Legend: proper name = the GPIO line is used as GPIO
+ *         NC = not connected (not routed from the SoC)
+ *         "[PER]" = pin is muxed for peripheral (not GPIO)
+ *         "" = no idea, schematic doesn't say, could be
+ *              unrouted (not connected to any external pin)
+ *         LSEC = Low Speed External Connector
+ *         HSEC = High Speed External Connector
+ *
+ * Pin assignments taken from LeMaker and CircuitCo Schematics
+ * Rev A1.
+ *
+ * For the lines routed to the external connectors the
+ * lines are named after the 96Boards CE Specification 1.0,
+ * Appendix "Expansion Connector Signal Description".
+ *
+ * When the 96Board naming of a line and the schematic name of
+ * the same line are in conflict, the 96Board specification
+ * takes precedence, which means that the external UART on the
+ * LSEC is named UART0 while the schematic and SoC names this
+ * UART2. This is only for the informational lines i.e. "[FOO]",
+ * the GPIO named lines "GPIO-A" thru "GPIO-L" are the only
+ * ones actually used for GPIO.
+ */
+&gpio0 {
+	gpio-line-names = "PWR_HOLD", "DSI_SEL",
+	"USB_HUB_RESET_N", "USB_SEL", "HDMI_PD", "WL_REG_ON",
+	"PWRON_DET", "5V_HUB_EN";
+};
+
+&gpio1 {
+	gpio-line-names = "SD_DET", "HDMI_INT", "PMU_IRQ_N",
+	"WL_HOST_WAKE", "NC", "NC", "NC", "BT_REG_ON";
+};
+
+&gpio2 {
+	gpio-line-names =
+		"GPIO-A", /* LSEC Pin 23: GPIO2_0 */
+		"GPIO-B", /* LSEC Pin 24: GPIO2_1 */
+		"GPIO-C", /* LSEC Pin 25: GPIO2_2 */
+		"GPIO-D", /* LSEC Pin 26: GPIO2_3 */
+		"GPIO-E", /* LSEC Pin 27: GPIO2_4 */
+		"USB_ID_DET", "USB_VBUS_DET",
+		"GPIO-H"; /* LSEC Pin 30: GPIO2_7 */
+};
+
+&gpio3 {
+	gpio-line-names = "GPIO3_0", "NC", "NC", "", "NC", "",
+	"WLAN_ACTIVE", "NC", "NC";
+};
+
+&gpio4 {
+	gpio-line-names = "USER_LED1", "USER_LED2", "USER_LED3",
+	"USER_LED4", "SD_SEL", "NC", "NC", "BT_ACTIVE";
+};
+
+&gpio5 {
+	gpio-line-names = "NC", "NC",
+	"[UART1_RxD]", /* LSEC Pin 11: UART3_RX */
+	"[UART1_TxD]", /* LSEC Pin 13: UART3_TX */
+	"[AUX_SSI1]", "NC",
+	"[PCM_CLK]", /* LSEC Pin 18: MODEM_PCM_XCLK */
+	"[PCM_FS]"; /* LSEC Pin 16: MODEM_PCM_XFS */
+};
+
+&gpio6 {
+	gpio-line-names =
+	"[SPI0_DIN]", /* Pin 10: SPI0_DI */
+	"[SPI0_DOUT]", /* Pin 14: SPI0_DO */
+	"[SPI0_CS]", /* Pin 12: SPI0_CS_N */
+	"[SPI0_SCLK]", /* Pin 8: SPI0_SCLK */
+	"NC", "NC", "NC",
+	"GPIO-G"; /* Pin 29: GPIO6_7_DSI_TE0 */
+};
+
+&gpio7 {
+	gpio-line-names = "NC", "NC", "NC", "NC",
+	"[PCM_DI]", /* Pin 22: MODEM_PCM_DI */
+	"[PCM_DO]", /* Pin 20: MODEM_PCM_DO */
+	"NC", "NC";
+};
+
+&gpio8 {
+	gpio-line-names = "NC", "[CEC_CLK_19_2MHZ]", "NC",
+	"", "", "", "", "", "";
+};
+
+&gpio9 {
+	gpio-line-names = "",
+	"GPIO-J", /* LSEC Pin 32: ISP_PWDN0_GPIO9_1 */
+	"GPIO-L", /* LSEC Pin 34: ISP_PWDN1_GPIO9_2 */
+	"NC", "NC", "NC", "NC", "[ISP_CCLK0]";
+};
+
+&gpio10 {
+	gpio-line-names = "BOOT_SEL",
+	"[ISP_CCLK1]",
+	"GPIO-I", /* LSEC Pin 31: ISP_RSTB0_GPIO10_2 */
+	"GPIO-K", /* LSEC Pin 33: ISP_RSTB1_GPIO10_3 */
+	"NC", "NC",
+	"[I2C2_SDA]", /* HSEC Pin 34: ISP0_SDA */
+	"[I2C2_SCL]"; /* HSEC Pin 32: ISP0_SCL */
+};
+
+&gpio11 {
+	gpio-line-names =
+	"[I2C3_SDA]", /* HSEC Pin 38: ISP1_SDA */
+	"[I2C3_SCL]", /* HSEC Pin 36: ISP1_SCL */
+	"", "NC", "NC", "NC", "", "";
+};
+
+&gpio12 {
+	gpio-line-names = "[BT_PCM_XFS]", "[BT_PCM_DI]",
+	"[BT_PCM_DO]",
+	"NC", "NC", "NC", "NC",
+	"GPIO-F"; /* LSEC Pin 28: BL_PWM_GPIO12_7 */
+};
+
+&gpio13 {
+	gpio-line-names = "[UART0_RX]", "[UART0_TX]",
+	"[BT_UART1_CTS]", "[BT_UART1_RTS]",
+	"[BT_UART1_RX]", "[BT_UART1_TX]",
+	"[UART0_CTS]", /* LSEC Pin 3: UART2_CTS_N */
+	"[UART0_RTS]"; /* LSEC Pin 9: UART2_RTS_N */
+};
+
+&gpio14 {
+	gpio-line-names =
+	"[UART0_RxD]", /* LSEC Pin 7: UART2_RX */
+	"[UART0_TxD]", /* LSEC Pin 5: UART2_TX */
+	"[I2C0_SCL]", /* LSEC Pin 15: I2C0_SCL */
+	"[I2C0_SDA]", /* LSEC Pin 17: I2C0_SDA */
+	"[I2C1_SCL]", /* LSEC Pin 19: I2C1_SCL */
+	"[I2C1_SDA]", /* LSEC Pin 21: I2C1_SDA */
+	"[I2C2_SCL]", "[I2C2_SDA]";
+};
+
+&gpio15 {
+	gpio-line-names = "", "", "", "", "", "", "NC", "";
+};
+
+/* GPIO blocks 16 thru 19 do not appear to be routed to pins */
+
+
+&i2c0 {
+	status = "okay";
+};
+
+&i2c1 {
+	status = "okay";
+};
+
+&i2c2 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	adv7533: adv7533@39 {
+		compatible = "adi,adv7533";
+		reg = <0x39>;
+		interrupt-parent = <&gpio1>;
+		interrupts = <1 2>;
+		pd-gpios = <&gpio0 4 0>;
+		adi,dsi-lanes = <4>;
+		#sound-dai-cells = <0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			port@0 {
+				adv7533_in: endpoint {
+					remote-endpoint = <&dsi_out0>;
+				};
+			};
+			port@2 {
+				reg = <2>;
+				codec_endpoint: endpoint {
+					remote-endpoint = <&i2s0_cpu_endpoint>;
+				};
+			};
+		};
+	};
+};
+
+&i2s0 {
+
+	ports {
+		i2s0_port0: port@0 {
+			i2s0_cpu_endpoint: endpoint {
+				remote-endpoint = <&codec_endpoint>;
+				dai-format = "i2s";
+			};
+		};
+	};
+};
+
+&spi0 {
+	status = "okay";
+};