Adding upstream version 6.1.76.upstream/6.1.76

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 795 insertions, 0 deletions

diff --git a/drivers/net/ethernet/intel/igc/igc_phy.c b/drivers/net/ethernet/intel/igc/igc_phy.c
new file mode 100644
index 000000000..53b77c969
--- /dev/null
+++ b/drivers/net/ethernet/intel/igc/igc_phy.c
@@ -0,0 +1,795 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c)  2018 Intel Corporation */
+
+#include "igc_phy.h"
+
+/**
+ * igc_check_reset_block - Check if PHY reset is blocked
+ * @hw: pointer to the HW structure
+ *
+ * Read the PHY management control register and check whether a PHY reset
+ * is blocked.  If a reset is not blocked return 0, otherwise
+ * return IGC_ERR_BLK_PHY_RESET (12).
+ */
+s32 igc_check_reset_block(struct igc_hw *hw)
+{
+	u32 manc;
+
+	manc = rd32(IGC_MANC);
+
+	return (manc & IGC_MANC_BLK_PHY_RST_ON_IDE) ?
+		IGC_ERR_BLK_PHY_RESET : 0;
+}
+
+/**
+ * igc_get_phy_id - Retrieve the PHY ID and revision
+ * @hw: pointer to the HW structure
+ *
+ * Reads the PHY registers and stores the PHY ID and possibly the PHY
+ * revision in the hardware structure.
+ */
+s32 igc_get_phy_id(struct igc_hw *hw)
+{
+	struct igc_phy_info *phy = &hw->phy;
+	s32 ret_val = 0;
+	u16 phy_id;
+
+	ret_val = phy->ops.read_reg(hw, PHY_ID1, &phy_id);
+	if (ret_val)
+		goto out;
+
+	phy->id = (u32)(phy_id << 16);
+	usleep_range(200, 500);
+	ret_val = phy->ops.read_reg(hw, PHY_ID2, &phy_id);
+	if (ret_val)
+		goto out;
+
+	phy->id |= (u32)(phy_id & PHY_REVISION_MASK);
+	phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
+
+out:
+	return ret_val;
+}
+
+/**
+ * igc_phy_has_link - Polls PHY for link
+ * @hw: pointer to the HW structure
+ * @iterations: number of times to poll for link
+ * @usec_interval: delay between polling attempts
+ * @success: pointer to whether polling was successful or not
+ *
+ * Polls the PHY status register for link, 'iterations' number of times.
+ */
+s32 igc_phy_has_link(struct igc_hw *hw, u32 iterations,
+		     u32 usec_interval, bool *success)
+{
+	u16 i, phy_status;
+	s32 ret_val = 0;
+
+	for (i = 0; i < iterations; i++) {
+		/* Some PHYs require the PHY_STATUS register to be read
+		 * twice due to the link bit being sticky.  No harm doing
+		 * it across the board.
+		 */
+		ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
+		if (ret_val && usec_interval > 0) {
+			/* If the first read fails, another entity may have
+			 * ownership of the resources, wait and try again to
+			 * see if they have relinquished the resources yet.
+			 */
+			if (usec_interval >= 1000)
+				mdelay(usec_interval / 1000);
+			else
+				udelay(usec_interval);
+		}
+		ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
+		if (ret_val)
+			break;
+		if (phy_status & MII_SR_LINK_STATUS)
+			break;
+		if (usec_interval >= 1000)
+			mdelay(usec_interval / 1000);
+		else
+			udelay(usec_interval);
+	}
+
+	*success = (i < iterations) ? true : false;
+
+	return ret_val;
+}
+
+/**
+ * igc_power_up_phy_copper - Restore copper link in case of PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, restore the link to previous settings.
+ */
+void igc_power_up_phy_copper(struct igc_hw *hw)
+{
+	u16 mii_reg = 0;
+
+	/* The PHY will retain its settings across a power down/up cycle */
+	hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg);
+	mii_reg &= ~MII_CR_POWER_DOWN;
+	hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg);
+}
+
+/**
+ * igc_power_down_phy_copper - Power down copper PHY
+ * @hw: pointer to the HW structure
+ *
+ * Power down PHY to save power when interface is down and wake on lan
+ * is not enabled.
+ */
+void igc_power_down_phy_copper(struct igc_hw *hw)
+{
+	u16 mii_reg = 0;
+
+	/* The PHY will retain its settings across a power down/up cycle */
+	hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg);
+	mii_reg |= MII_CR_POWER_DOWN;
+
+	/* Temporary workaround - should be removed when PHY will implement
+	 * IEEE registers as properly
+	 */
+	/* hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg);*/
+	usleep_range(1000, 2000);
+}
+
+/**
+ * igc_check_downshift - Checks whether a downshift in speed occurred
+ * @hw: pointer to the HW structure
+ *
+ * A downshift is detected by querying the PHY link health.
+ */
+void igc_check_downshift(struct igc_hw *hw)
+{
+	struct igc_phy_info *phy = &hw->phy;
+
+	/* speed downshift not supported */
+	phy->speed_downgraded = false;
+}
+
+/**
+ * igc_phy_hw_reset - PHY hardware reset
+ * @hw: pointer to the HW structure
+ *
+ * Verify the reset block is not blocking us from resetting.  Acquire
+ * semaphore (if necessary) and read/set/write the device control reset
+ * bit in the PHY.  Wait the appropriate delay time for the device to
+ * reset and release the semaphore (if necessary).
+ */
+s32 igc_phy_hw_reset(struct igc_hw *hw)
+{
+	struct igc_phy_info *phy = &hw->phy;
+	u32 phpm = 0, timeout = 10000;
+	s32  ret_val;
+	u32 ctrl;
+
+	ret_val = igc_check_reset_block(hw);
+	if (ret_val) {
+		ret_val = 0;
+		goto out;
+	}
+
+	ret_val = phy->ops.acquire(hw);
+	if (ret_val)
+		goto out;
+
+	phpm = rd32(IGC_I225_PHPM);
+
+	ctrl = rd32(IGC_CTRL);
+	wr32(IGC_CTRL, ctrl | IGC_CTRL_PHY_RST);
+	wrfl();
+
+	udelay(phy->reset_delay_us);
+
+	wr32(IGC_CTRL, ctrl);
+	wrfl();
+
+	/* SW should guarantee 100us for the completion of the PHY reset */
+	usleep_range(100, 150);
+	do {
+		phpm = rd32(IGC_I225_PHPM);
+		timeout--;
+		udelay(1);
+	} while (!(phpm & IGC_PHY_RST_COMP) && timeout);
+
+	if (!timeout)
+		hw_dbg("Timeout is expired after a phy reset\n");
+
+	usleep_range(100, 150);
+
+	phy->ops.release(hw);
+
+out:
+	return ret_val;
+}
+
+/**
+ * igc_phy_setup_autoneg - Configure PHY for auto-negotiation
+ * @hw: pointer to the HW structure
+ *
+ * Reads the MII auto-neg advertisement register and/or the 1000T control
+ * register and if the PHY is already setup for auto-negotiation, then
+ * return successful.  Otherwise, setup advertisement and flow control to
+ * the appropriate values for the wanted auto-negotiation.
+ */
+static s32 igc_phy_setup_autoneg(struct igc_hw *hw)
+{
+	struct igc_phy_info *phy = &hw->phy;
+	u16 aneg_multigbt_an_ctrl = 0;
+	u16 mii_1000t_ctrl_reg = 0;
+	u16 mii_autoneg_adv_reg;
+	s32 ret_val;
+
+	phy->autoneg_advertised &= phy->autoneg_mask;
+
+	/* Read the MII Auto-Neg Advertisement Register (Address 4). */
+	ret_val = phy->ops.read_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg);
+	if (ret_val)
+		return ret_val;
+
+	if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
+		/* Read the MII 1000Base-T Control Register (Address 9). */
+		ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL,
+					    &mii_1000t_ctrl_reg);
+		if (ret_val)
+			return ret_val;
+	}
+
+	if (phy->autoneg_mask & ADVERTISE_2500_FULL) {
+		/* Read the MULTI GBT AN Control Register - reg 7.32 */
+		ret_val = phy->ops.read_reg(hw, (STANDARD_AN_REG_MASK <<
+					    MMD_DEVADDR_SHIFT) |
+					    ANEG_MULTIGBT_AN_CTRL,
+					    &aneg_multigbt_an_ctrl);
+
+		if (ret_val)
+			return ret_val;
+	}
+
+	/* Need to parse both autoneg_advertised and fc and set up
+	 * the appropriate PHY registers.  First we will parse for
+	 * autoneg_advertised software override.  Since we can advertise
+	 * a plethora of combinations, we need to check each bit
+	 * individually.
+	 */
+
+	/* First we clear all the 10/100 mb speed bits in the Auto-Neg
+	 * Advertisement Register (Address 4) and the 1000 mb speed bits in
+	 * the  1000Base-T Control Register (Address 9).
+	 */
+	mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS |
+				 NWAY_AR_100TX_HD_CAPS |
+				 NWAY_AR_10T_FD_CAPS   |
+				 NWAY_AR_10T_HD_CAPS);
+	mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS);
+
+	hw_dbg("autoneg_advertised %x\n", phy->autoneg_advertised);
+
+	/* Do we want to advertise 10 Mb Half Duplex? */
+	if (phy->autoneg_advertised & ADVERTISE_10_HALF) {
+		hw_dbg("Advertise 10mb Half duplex\n");
+		mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS;
+	}
+
+	/* Do we want to advertise 10 Mb Full Duplex? */
+	if (phy->autoneg_advertised & ADVERTISE_10_FULL) {
+		hw_dbg("Advertise 10mb Full duplex\n");
+		mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS;
+	}
+
+	/* Do we want to advertise 100 Mb Half Duplex? */
+	if (phy->autoneg_advertised & ADVERTISE_100_HALF) {
+		hw_dbg("Advertise 100mb Half duplex\n");
+		mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS;
+	}
+
+	/* Do we want to advertise 100 Mb Full Duplex? */
+	if (phy->autoneg_advertised & ADVERTISE_100_FULL) {
+		hw_dbg("Advertise 100mb Full duplex\n");
+		mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS;
+	}
+
+	/* We do not allow the Phy to advertise 1000 Mb Half Duplex */
+	if (phy->autoneg_advertised & ADVERTISE_1000_HALF)
+		hw_dbg("Advertise 1000mb Half duplex request denied!\n");
+
+	/* Do we want to advertise 1000 Mb Full Duplex? */
+	if (phy->autoneg_advertised & ADVERTISE_1000_FULL) {
+		hw_dbg("Advertise 1000mb Full duplex\n");
+		mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS;
+	}
+
+	/* We do not allow the Phy to advertise 2500 Mb Half Duplex */
+	if (phy->autoneg_advertised & ADVERTISE_2500_HALF)
+		hw_dbg("Advertise 2500mb Half duplex request denied!\n");
+
+	/* Do we want to advertise 2500 Mb Full Duplex? */
+	if (phy->autoneg_advertised & ADVERTISE_2500_FULL) {
+		hw_dbg("Advertise 2500mb Full duplex\n");
+		aneg_multigbt_an_ctrl |= CR_2500T_FD_CAPS;
+	} else {
+		aneg_multigbt_an_ctrl &= ~CR_2500T_FD_CAPS;
+	}
+
+	/* Check for a software override of the flow control settings, and
+	 * setup the PHY advertisement registers accordingly.  If
+	 * auto-negotiation is enabled, then software will have to set the
+	 * "PAUSE" bits to the correct value in the Auto-Negotiation
+	 * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto-
+	 * negotiation.
+	 *
+	 * The possible values of the "fc" parameter are:
+	 *      0:  Flow control is completely disabled
+	 *      1:  Rx flow control is enabled (we can receive pause frames
+	 *          but not send pause frames).
+	 *      2:  Tx flow control is enabled (we can send pause frames
+	 *          but we do not support receiving pause frames).
+	 *      3:  Both Rx and Tx flow control (symmetric) are enabled.
+	 *  other:  No software override.  The flow control configuration
+	 *          in the EEPROM is used.
+	 */
+	switch (hw->fc.current_mode) {
+	case igc_fc_none:
+		/* Flow control (Rx & Tx) is completely disabled by a
+		 * software over-ride.
+		 */
+		mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		break;
+	case igc_fc_rx_pause:
+		/* Rx Flow control is enabled, and Tx Flow control is
+		 * disabled, by a software over-ride.
+		 *
+		 * Since there really isn't a way to advertise that we are
+		 * capable of Rx Pause ONLY, we will advertise that we
+		 * support both symmetric and asymmetric Rx PAUSE.  Later
+		 * (in igc_config_fc_after_link_up) we will disable the
+		 * hw's ability to send PAUSE frames.
+		 */
+		mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		break;
+	case igc_fc_tx_pause:
+		/* Tx Flow control is enabled, and Rx Flow control is
+		 * disabled, by a software over-ride.
+		 */
+		mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR;
+		mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE;
+		break;
+	case igc_fc_full:
+		/* Flow control (both Rx and Tx) is enabled by a software
+		 * over-ride.
+		 */
+		mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE);
+		break;
+	default:
+		hw_dbg("Flow control param set incorrectly\n");
+		return -IGC_ERR_CONFIG;
+	}
+
+	ret_val = phy->ops.write_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg);
+	if (ret_val)
+		return ret_val;
+
+	hw_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
+
+	if (phy->autoneg_mask & ADVERTISE_1000_FULL)
+		ret_val = phy->ops.write_reg(hw, PHY_1000T_CTRL,
+					     mii_1000t_ctrl_reg);
+
+	if (phy->autoneg_mask & ADVERTISE_2500_FULL)
+		ret_val = phy->ops.write_reg(hw,
+					     (STANDARD_AN_REG_MASK <<
+					     MMD_DEVADDR_SHIFT) |
+					     ANEG_MULTIGBT_AN_CTRL,
+					     aneg_multigbt_an_ctrl);
+
+	return ret_val;
+}
+
+/**
+ * igc_wait_autoneg - Wait for auto-neg completion
+ * @hw: pointer to the HW structure
+ *
+ * Waits for auto-negotiation to complete or for the auto-negotiation time
+ * limit to expire, which ever happens first.
+ */
+static s32 igc_wait_autoneg(struct igc_hw *hw)
+{
+	u16 i, phy_status;
+	s32 ret_val = 0;
+
+	/* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */
+	for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) {
+		ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
+		if (ret_val)
+			break;
+		ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status);
+		if (ret_val)
+			break;
+		if (phy_status & MII_SR_AUTONEG_COMPLETE)
+			break;
+		msleep(100);
+	}
+
+	/* PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation
+	 * has completed.
+	 */
+	return ret_val;
+}
+
+/**
+ * igc_copper_link_autoneg - Setup/Enable autoneg for copper link
+ * @hw: pointer to the HW structure
+ *
+ * Performs initial bounds checking on autoneg advertisement parameter, then
+ * configure to advertise the full capability.  Setup the PHY to autoneg
+ * and restart the negotiation process between the link partner.  If
+ * autoneg_wait_to_complete, then wait for autoneg to complete before exiting.
+ */
+static s32 igc_copper_link_autoneg(struct igc_hw *hw)
+{
+	struct igc_phy_info *phy = &hw->phy;
+	u16 phy_ctrl;
+	s32 ret_val;
+
+	/* Perform some bounds checking on the autoneg advertisement
+	 * parameter.
+	 */
+	phy->autoneg_advertised &= phy->autoneg_mask;
+
+	/* If autoneg_advertised is zero, we assume it was not defaulted
+	 * by the calling code so we set to advertise full capability.
+	 */
+	if (phy->autoneg_advertised == 0)
+		phy->autoneg_advertised = phy->autoneg_mask;
+
+	hw_dbg("Reconfiguring auto-neg advertisement params\n");
+	ret_val = igc_phy_setup_autoneg(hw);
+	if (ret_val) {
+		hw_dbg("Error Setting up Auto-Negotiation\n");
+		goto out;
+	}
+	hw_dbg("Restarting Auto-Neg\n");
+
+	/* Restart auto-negotiation by setting the Auto Neg Enable bit and
+	 * the Auto Neg Restart bit in the PHY control register.
+	 */
+	ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_ctrl);
+	if (ret_val)
+		goto out;
+
+	phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG);
+	ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_ctrl);
+	if (ret_val)
+		goto out;
+
+	/* Does the user want to wait for Auto-Neg to complete here, or
+	 * check at a later time (for example, callback routine).
+	 */
+	if (phy->autoneg_wait_to_complete) {
+		ret_val = igc_wait_autoneg(hw);
+		if (ret_val) {
+			hw_dbg("Error while waiting for autoneg to complete\n");
+			goto out;
+		}
+	}
+
+	hw->mac.get_link_status = true;
+
+out:
+	return ret_val;
+}
+
+/**
+ * igc_setup_copper_link - Configure copper link settings
+ * @hw: pointer to the HW structure
+ *
+ * Calls the appropriate function to configure the link for auto-neg or forced
+ * speed and duplex.  Then we check for link, once link is established calls
+ * to configure collision distance and flow control are called.  If link is
+ * not established, we return -IGC_ERR_PHY (-2).
+ */
+s32 igc_setup_copper_link(struct igc_hw *hw)
+{
+	s32 ret_val = 0;
+	bool link;
+
+	if (hw->mac.autoneg) {
+		/* Setup autoneg and flow control advertisement and perform
+		 * autonegotiation.
+		 */
+		ret_val = igc_copper_link_autoneg(hw);
+		if (ret_val)
+			goto out;
+	} else {
+		/* PHY will be set to 10H, 10F, 100H or 100F
+		 * depending on user settings.
+		 */
+		hw_dbg("Forcing Speed and Duplex\n");
+		ret_val = hw->phy.ops.force_speed_duplex(hw);
+		if (ret_val) {
+			hw_dbg("Error Forcing Speed and Duplex\n");
+			goto out;
+		}
+	}
+
+	/* Check link status. Wait up to 100 microseconds for link to become
+	 * valid.
+	 */
+	ret_val = igc_phy_has_link(hw, COPPER_LINK_UP_LIMIT, 10, &link);
+	if (ret_val)
+		goto out;
+
+	if (link) {
+		hw_dbg("Valid link established!!!\n");
+		igc_config_collision_dist(hw);
+		ret_val = igc_config_fc_after_link_up(hw);
+	} else {
+		hw_dbg("Unable to establish link!!!\n");
+	}
+
+out:
+	return ret_val;
+}
+
+/**
+ * igc_read_phy_reg_mdic - Read MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to be read
+ * @data: pointer to the read data
+ *
+ * Reads the MDI control register in the PHY at offset and stores the
+ * information read to data.
+ */
+static s32 igc_read_phy_reg_mdic(struct igc_hw *hw, u32 offset, u16 *data)
+{
+	struct igc_phy_info *phy = &hw->phy;
+	u32 i, mdic = 0;
+	s32 ret_val = 0;
+
+	if (offset > MAX_PHY_REG_ADDRESS) {
+		hw_dbg("PHY Address %d is out of range\n", offset);
+		ret_val = -IGC_ERR_PARAM;
+		goto out;
+	}
+
+	/* Set up Op-code, Phy Address, and register offset in the MDI
+	 * Control register.  The MAC will take care of interfacing with the
+	 * PHY to retrieve the desired data.
+	 */
+	mdic = ((offset << IGC_MDIC_REG_SHIFT) |
+		(phy->addr << IGC_MDIC_PHY_SHIFT) |
+		(IGC_MDIC_OP_READ));
+
+	wr32(IGC_MDIC, mdic);
+
+	/* Poll the ready bit to see if the MDI read completed
+	 * Increasing the time out as testing showed failures with
+	 * the lower time out
+	 */
+	for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) {
+		udelay(50);
+		mdic = rd32(IGC_MDIC);
+		if (mdic & IGC_MDIC_READY)
+			break;
+	}
+	if (!(mdic & IGC_MDIC_READY)) {
+		hw_dbg("MDI Read did not complete\n");
+		ret_val = -IGC_ERR_PHY;
+		goto out;
+	}
+	if (mdic & IGC_MDIC_ERROR) {
+		hw_dbg("MDI Error\n");
+		ret_val = -IGC_ERR_PHY;
+		goto out;
+	}
+	*data = (u16)mdic;
+
+out:
+	return ret_val;
+}
+
+/**
+ * igc_write_phy_reg_mdic - Write MDI control register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write to register at offset
+ *
+ * Writes data to MDI control register in the PHY at offset.
+ */
+static s32 igc_write_phy_reg_mdic(struct igc_hw *hw, u32 offset, u16 data)
+{
+	struct igc_phy_info *phy = &hw->phy;
+	u32 i, mdic = 0;
+	s32 ret_val = 0;
+
+	if (offset > MAX_PHY_REG_ADDRESS) {
+		hw_dbg("PHY Address %d is out of range\n", offset);
+		ret_val = -IGC_ERR_PARAM;
+		goto out;
+	}
+
+	/* Set up Op-code, Phy Address, and register offset in the MDI
+	 * Control register.  The MAC will take care of interfacing with the
+	 * PHY to write the desired data.
+	 */
+	mdic = (((u32)data) |
+		(offset << IGC_MDIC_REG_SHIFT) |
+		(phy->addr << IGC_MDIC_PHY_SHIFT) |
+		(IGC_MDIC_OP_WRITE));
+
+	wr32(IGC_MDIC, mdic);
+
+	/* Poll the ready bit to see if the MDI read completed
+	 * Increasing the time out as testing showed failures with
+	 * the lower time out
+	 */
+	for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) {
+		udelay(50);
+		mdic = rd32(IGC_MDIC);
+		if (mdic & IGC_MDIC_READY)
+			break;
+	}
+	if (!(mdic & IGC_MDIC_READY)) {
+		hw_dbg("MDI Write did not complete\n");
+		ret_val = -IGC_ERR_PHY;
+		goto out;
+	}
+	if (mdic & IGC_MDIC_ERROR) {
+		hw_dbg("MDI Error\n");
+		ret_val = -IGC_ERR_PHY;
+		goto out;
+	}
+
+out:
+	return ret_val;
+}
+
+/**
+ * __igc_access_xmdio_reg - Read/write XMDIO register
+ * @hw: pointer to the HW structure
+ * @address: XMDIO address to program
+ * @dev_addr: device address to program
+ * @data: pointer to value to read/write from/to the XMDIO address
+ * @read: boolean flag to indicate read or write
+ */
+static s32 __igc_access_xmdio_reg(struct igc_hw *hw, u16 address,
+				  u8 dev_addr, u16 *data, bool read)
+{
+	s32 ret_val;
+
+	ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, dev_addr);
+	if (ret_val)
+		return ret_val;
+
+	ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAAD, address);
+	if (ret_val)
+		return ret_val;
+
+	ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, IGC_MMDAC_FUNC_DATA |
+					dev_addr);
+	if (ret_val)
+		return ret_val;
+
+	if (read)
+		ret_val = hw->phy.ops.read_reg(hw, IGC_MMDAAD, data);
+	else
+		ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAAD, *data);
+	if (ret_val)
+		return ret_val;
+
+	/* Recalibrate the device back to 0 */
+	ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, 0);
+	if (ret_val)
+		return ret_val;
+
+	return ret_val;
+}
+
+/**
+ * igc_read_xmdio_reg - Read XMDIO register
+ * @hw: pointer to the HW structure
+ * @addr: XMDIO address to program
+ * @dev_addr: device address to program
+ * @data: value to be read from the EMI address
+ */
+static s32 igc_read_xmdio_reg(struct igc_hw *hw, u16 addr,
+			      u8 dev_addr, u16 *data)
+{
+	return __igc_access_xmdio_reg(hw, addr, dev_addr, data, true);
+}
+
+/**
+ * igc_write_xmdio_reg - Write XMDIO register
+ * @hw: pointer to the HW structure
+ * @addr: XMDIO address to program
+ * @dev_addr: device address to program
+ * @data: value to be written to the XMDIO address
+ */
+static s32 igc_write_xmdio_reg(struct igc_hw *hw, u16 addr,
+			       u8 dev_addr, u16 data)
+{
+	return __igc_access_xmdio_reg(hw, addr, dev_addr, &data, false);
+}
+
+/**
+ * igc_write_phy_reg_gpy - Write GPY PHY register
+ * @hw: pointer to the HW structure
+ * @offset: register offset to write to
+ * @data: data to write at register offset
+ *
+ * Acquires semaphore, if necessary, then writes the data to PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ */
+s32 igc_write_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 data)
+{
+	u8 dev_addr = (offset & GPY_MMD_MASK) >> GPY_MMD_SHIFT;
+	s32 ret_val;
+
+	offset = offset & GPY_REG_MASK;
+
+	if (!dev_addr) {
+		ret_val = hw->phy.ops.acquire(hw);
+		if (ret_val)
+			return ret_val;
+		ret_val = igc_write_phy_reg_mdic(hw, offset, data);
+		hw->phy.ops.release(hw);
+	} else {
+		ret_val = igc_write_xmdio_reg(hw, (u16)offset, dev_addr,
+					      data);
+	}
+
+	return ret_val;
+}
+
+/**
+ * igc_read_phy_reg_gpy - Read GPY PHY register
+ * @hw: pointer to the HW structure
+ * @offset: lower half is register offset to read to
+ * upper half is MMD to use.
+ * @data: data to read at register offset
+ *
+ * Acquires semaphore, if necessary, then reads the data in the PHY register
+ * at the offset. Release any acquired semaphores before exiting.
+ */
+s32 igc_read_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 *data)
+{
+	u8 dev_addr = (offset & GPY_MMD_MASK) >> GPY_MMD_SHIFT;
+	s32 ret_val;
+
+	offset = offset & GPY_REG_MASK;
+
+	if (!dev_addr) {
+		ret_val = hw->phy.ops.acquire(hw);
+		if (ret_val)
+			return ret_val;
+		ret_val = igc_read_phy_reg_mdic(hw, offset, data);
+		hw->phy.ops.release(hw);
+	} else {
+		ret_val = igc_read_xmdio_reg(hw, (u16)offset, dev_addr,
+					     data);
+	}
+
+	return ret_val;
+}
+
+/**
+ * igc_read_phy_fw_version - Read gPHY firmware version
+ * @hw: pointer to the HW structure
+ */
+u16 igc_read_phy_fw_version(struct igc_hw *hw)
+{
+	struct igc_phy_info *phy = &hw->phy;
+	u16 gphy_version = 0;
+	u16 ret_val;
+
+	/* NVM image version is reported as firmware version for i225 device */
+	ret_val = phy->ops.read_reg(hw, IGC_GPHY_VERSION, &gphy_version);
+	if (ret_val)
+		hw_dbg("igc_phy: read wrong gphy version\n");
+
+	return gphy_version;
+}