summaryrefslogtreecommitdiffstats
path: root/arch/arm/boot/dts/ste-hrefv60plus.dtsi
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/boot/dts/ste-hrefv60plus.dtsi')
-rw-r--r--arch/arm/boot/dts/ste-hrefv60plus.dtsi377
1 files changed, 377 insertions, 0 deletions
diff --git a/arch/arm/boot/dts/ste-hrefv60plus.dtsi b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
new file mode 100644
index 000000000..e66fa59c2
--- /dev/null
+++ b/arch/arm/boot/dts/ste-hrefv60plus.dtsi
@@ -0,0 +1,377 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Copyright 2012 ST-Ericsson AB
+ */
+
+#include "ste-href-ab8500.dtsi"
+#include "ste-href.dtsi"
+
+/ {
+ model = "ST-Ericsson HREF (v60+) platform with Device Tree";
+ compatible = "st-ericsson,hrefv60+", "st-ericsson,u8500";
+
+ thermal-zones {
+ chassis-thermal {
+ /* Poll every 20 seconds */
+ polling-delay = <20000>;
+ /* Poll every 2nd second when cooling */
+ polling-delay-passive = <2000>;
+
+ thermal-sensors = <&therm1>, <&therm2>;
+
+ /* Tripping points made from rough guess about operating conditions */
+ trips {
+ chassis_alert: chassis-alert {
+ /* At 50 degrees take down the CPU frequency */
+ temperature = <50000>;
+ hysteresis = <3000>;
+ type = "active";
+ };
+ chassis_crit: chassis-crit {
+ /* Just shut down at 70 degrees */
+ temperature = <70000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+
+ /* Push down the operating frequency of the SoC when it gets hot */
+ cooling-maps {
+ map0 {
+ trip = <&chassis_alert>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+ contribution = <100>;
+ };
+ };
+ };
+ };
+
+ /*
+ * Thermistors on the board, formally to monitor battery temperatures
+ * but what they measure is the board temperature.
+ */
+ therm1: thermistor@0 {
+ compatible = "murata,ncp18wb473";
+ io-channels = <&gpadc 0x06>; /* AUX1 */
+ pullup-uv = <1800000>;
+ pullup-ohm = <220000>;
+ pulldown-ohm = <0>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ therm2: thermistor@1 {
+ compatible = "murata,ncp18wb473";
+ io-channels = <&gpadc 0x07>; /* AUX2 */
+ pullup-uv = <1800000>;
+ pullup-ohm = <220000>;
+ pulldown-ohm = <0>;
+ #thermal-sensor-cells = <0>;
+ };
+
+ soc {
+ /* Name the GPIO muxed rails on the HREF boards */
+ gpio@8012e000 {
+ /* GPIOs 0 - 31 */
+ gpio-line-names =
+ /* GPIO0,1 used for UART0 BT RX/TX */
+ "", "",
+ "UART_WAKE",
+ "BT_WAKE",
+ "",
+ "SDMMC_1V8_3V_SEL",
+ "FLASH_LED_SYNC (FLASH_CTRL_0)",
+ "XENON_READY (FLASH_CTRL_1)",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "",
+ "",
+ "FLASH_LED_EN (FLASH_CTRL_3)",
+ "", "",
+ "", "", "", "", "",
+ /* Used by UART2 (console) */
+ "", "",
+ "MAGNETOMETER_INT";
+ };
+
+ gpio@8012e080 {
+ /* GPIOs 32 - 63 */
+ gpio-line-names =
+ "MAGNETOMETER_DRDY",
+ "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
+ gpio@8000e000 {
+ /* GPIOs 64 - 95 */
+ gpio-line-names = "XENON_EN2 (FLASH_CTRL_4)",
+ "DISP1_RST",
+ "DISP2_RST",
+ "TOUCH_INT2",
+ "LCD_VSI0_A",
+ "LCD_VSI1_A",
+ /* GPIO 70-77 used for ETM */
+ "", "", "", "", "", "", "", "",
+ /* GPIO 78-81 used for YCBCR */
+ "", "", "", "",
+ "ACCELEROMETER_INT1_RDY",
+ "ACCELEROMETER_INT2",
+ "TOUCH_INT",
+ "WLAN_ENA",
+ "", "", "", "", "",
+ "FORCE_SENSING_INT",
+ "FORCE_SENSING_RESET",
+ "", "",
+ "SDMMC_CD";
+ };
+
+ gpio@8000e080 {
+ /* GPIOs 96 - 127 */
+ gpio-line-names = "",
+ "FORCE_SENSING_WU",
+ "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
+ gpio@8000e100 {
+ /* GPIOs 128 - 159 */
+ gpio-line-names = "", "", "", "", "", "", "", "",
+ "", "", "",
+ "DIPRO_INT", /* GPIO139 */
+ "XSHUTDOWN_SECONDARY_SENSOR",
+ "XSHUTDOWN_PRIMARY_SENSOR",
+ "NFC_RST (NFC_CTRL_",
+ "TOUCH_RST",
+ "NFC_IRQ (NFC_CTRL_1)",
+ "HAL_SW",
+ "TOUCH_RST2",
+ "", "",
+ "VAUDIO_HF_EN", /* GPIO149 */
+ "", "", "", "", "", "", "", "", "", "";
+ };
+
+ gpio@8000e180 {
+ /* GPIOs 160 - 191 */
+ gpio-line-names = "", "", "", "", "", "", "", "",
+ "",
+ "SDMMC_EN",
+ "XENON_CHARGE (FLASH_CONTROL_5)",
+ "GBF_ENA_RESET",
+ "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
+ gpio@8011e000 {
+ /* GPIOs 192 - 223 */
+ gpio-line-names = "HDTV_INTN",
+ "", "", "",
+ "HDTV_RSTN",
+ "", "", "",
+ "", /* GPIO200 */
+ "", "", "", "", "", "", "",
+ /* GPIO208-216 used for WGBF_MC1 */
+ "", "", "", "", "", "", "", "", "",
+ "SW_FRONT_PROXIMITY", /* GPIO217 */
+ "KPD_CTRL_INT", /* Keypad controller */
+ "", "", "", "", "";
+ };
+
+ gpio@8011e080 {
+ /* GPIOs 224 - 255 */
+ gpio-line-names = "", "",
+ "HSIT_ACWAKE0",
+ "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+ };
+
+ // External Micro SD slot
+ mmc@80126000 {
+ cd-gpios = <&gpio2 31 GPIO_ACTIVE_HIGH>; // 95
+ };
+
+ pinctrl {
+ /*
+ * Set this up using hogs, as time goes by and as seems fit, these
+ * can be moved over to being controlled by respective device.
+ */
+ pinctrl-names = "default";
+ pinctrl-0 = <&ipgpio_hrefv60_mode>,
+ <&etm_hrefv60_mode>,
+ <&nahj_hrefv60_mode>,
+ <&nfc_hrefv60_mode>,
+ <&force_hrefv60_mode>,
+ <&dipro_hrefv60_mode>,
+ <&vaudio_hf_hrefv60_mode>,
+ <&gbf_hrefv60_mode>,
+ <&hdtv_hrefv60_mode>,
+ <&gpios_hrefv60_mode>;
+
+ sdi0 {
+ sdi0_default_mode: sdi0_default {
+ /* SD card detect GPIO pin, extend default state */
+ default_hrefv60_cfg1 {
+ pins = "GPIO95_E8";
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ ipgpio {
+ /*
+ * XENON Flashgun on image processor GPIO (controlled from image
+ * processor firmware), mux in these image processor GPIO lines 0
+ * (XENON_FLASH_ID), 1 (XENON_READY) and there is an assistant
+ * LED on IP GPIO 4 (XENON_EN2) on altfunction C, that need bias
+ * from GPIO21 so pull up 0, 1 and drive 4 and GPIO21 low as output.
+ */
+ ipgpio_hrefv60_mode: ipgpio_hrefv60 {
+ hrefv60_mux {
+ function = "ipgpio";
+ groups = "ipgpio0_c_1", "ipgpio1_c_1", "ipgpio4_c_1";
+ };
+ hrefv60_cfg1 {
+ pins = "GPIO6_AF6", "GPIO7_AG5";
+ ste,config = <&in_pu>;
+ };
+ hrefv60_cfg2 {
+ pins = "GPIO21_AB3";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg3 {
+ pins = "GPIO64_F3";
+ ste,config = <&out_lo>;
+ };
+ };
+ };
+ etm {
+ /*
+ * Drive D19-D23 for the ETM PTM trace interface low,
+ * (presumably pins are unconnected therefore grounded here,
+ * the "other alt C1" setting enables these pins)
+ */
+ etm_hrefv60_mode: etm_hrefv60 {
+ hrefv60_cfg1 {
+ pins =
+ "GPIO70_G5",
+ "GPIO71_G4",
+ "GPIO72_H4",
+ "GPIO73_H3",
+ "GPIO74_J3";
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ nahj {
+ nahj_hrefv60_mode: nahj_hrefv60 {
+ /* NAHJ CTRL on GPIO76 to low, CTRL_INV on GPIO216 to high */
+ hrefv60_cfg1 {
+ pins = "GPIO76_J2";
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ pins = "GPIO216_AG12";
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ nfc {
+ nfc_hrefv60_mode: nfc_hrefv60 {
+ /* NFC ENA and RESET to low, pulldown IRQ line */
+ hrefv60_cfg1 {
+ pins =
+ "GPIO77_H1", /* NFC_ENA */
+ "GPIO142_C11"; /* NFC_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ hrefv60_cfg2 {
+ pins = "GPIO144_B13"; /* NFC_IRQ */
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ force {
+ force_hrefv60_mode: force_hrefv60 {
+ hrefv60_cfg1 {
+ pins = "GPIO91_B6"; /* FORCE_SENSING_INT */
+ ste,config = <&gpio_in_pu>;
+ };
+ hrefv60_cfg2 {
+ pins =
+ "GPIO92_D6", /* FORCE_SENSING_RST */
+ "GPIO97_D9"; /* FORCE_SENSING_WU */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ dipro {
+ dipro_hrefv60_mode: dipro_hrefv60 {
+ hrefv60_cfg1 {
+ pins = "GPIO139_C9"; /* DIPRO_INT */
+ ste,config = <&gpio_in_pu>;
+ };
+ };
+ };
+ vaudio_hf {
+ vaudio_hf_hrefv60_mode: vaudio_hf_hrefv60 {
+ /* Audio Amplifier HF enable GPIO */
+ hrefv60_cfg1 {
+ pins = "GPIO149_B14"; /* VAUDIO_HF_EN, enable MAX8968 */
+ ste,config = <&gpio_out_hi>;
+ };
+ };
+ };
+ gbf {
+ gbf_hrefv60_mode: gbf_hrefv60 {
+ /*
+ * GBF (GPS, Bluetooth, FM-radio) interface,
+ * pull low to reset state
+ */
+ hrefv60_cfg1 {
+ pins = "GPIO171_D23"; /* GBF_ENA_RESET */
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ hdtv {
+ hdtv_hrefv60_mode: hdtv_hrefv60 {
+ /* MSP : HDTV INTERFACE GPIO line */
+ hrefv60_cfg1 {
+ pins = "GPIO192_AJ27";
+ ste,config = <&gpio_in_pd>;
+ };
+ };
+ };
+ mcde {
+ lcd_hrefv60_mode: lcd_hrefv60 {
+ /*
+ * Display Interface 1 uses GPIO 65 for RST (reset).
+ * Display Interface 2 uses GPIO 66 for RST (reset).
+ * Drive DISP1 reset high (not reset), driver DISP2 reset low (reset)
+ */
+ hrefv60_cfg1 {
+ pins = "GPIO65_F1";
+ ste,config = <&gpio_out_hi>;
+ };
+ hrefv60_cfg2 {
+ pins = "GPIO66_G3";
+ ste,config = <&gpio_out_lo>;
+ };
+ };
+ };
+ gpios {
+ /* Dangling GPIO pins */
+ gpios_hrefv60_mode: gpios_hrefv60 {
+ default_cfg1 {
+ /* Normally UART1 RXD, now dangling */
+ pins = "GPIO4_AH6";
+ ste,config = <&in_pu>;
+ };
+ };
+ };
+ };
+ };
+};