1 files changed, 128 insertions, 0 deletions
diff --git a/arch/arm/mach-ep93xx/simone.c b/arch/arm/mach-ep93xx/simone.c
new file mode 100644
index 000000000..569e72413
--- /dev/null
+++ b/arch/arm/mach-ep93xx/simone.c
@@ -0,0 +1,128 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * arch/arm/mach-ep93xx/simone.c
+ * Simplemachines Sim.One support.
+ *
+ * Copyright (C) 2010 Ryan Mallon
+ *
+ * Based on the 2.6.24.7 support:
+ *   Copyright (C) 2009 Simplemachines
+ *   MMC support by Peter Ivanov <ivanovp@gmail.com>, 2007
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/i2c.h>
+#include <linux/mmc/host.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/mmc_spi.h>
+#include <linux/platform_data/video-ep93xx.h>
+#include <linux/platform_data/spi-ep93xx.h>
+#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
+
+#include "hardware.h"
+#include "gpio-ep93xx.h"
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+
+#include "soc.h"
+
+static struct ep93xx_eth_data __initdata simone_eth_data = {
+	.phy_id		= 1,
+};
+
+static struct ep93xxfb_mach_info __initdata simone_fb_info = {
+	.flags		= EP93XXFB_USE_SDCSN0 | EP93XXFB_PCLK_FALLING,
+};
+
+static struct mmc_spi_platform_data simone_mmc_spi_data = {
+	.detect_delay	= 500,
+	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
+};
+
+static struct gpiod_lookup_table simone_mmc_spi_gpio_table = {
+	.dev_id = "mmc_spi.0", /* "mmc_spi" @ CS0 */
+	.table = {
+		/* Card detect */
+		GPIO_LOOKUP_IDX("A", 0, NULL, 0, GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
+static struct spi_board_info simone_spi_devices[] __initdata = {
+	{
+		.modalias		= "mmc_spi",
+		.platform_data		= &simone_mmc_spi_data,
+		/*
+		 * We use 10 MHz even though the maximum is 3.7 MHz. The driver
+		 * will limit it automatically to max. frequency.
+		 */
+		.max_speed_hz		= 10 * 1000 * 1000,
+		.bus_num		= 0,
+		.chip_select		= 0,
+		.mode			= SPI_MODE_3,
+	},
+};
+
+/*
+ * Up to v1.3, the Sim.One used SFRMOUT as SD card chip select, but this goes
+ * low between multi-message command blocks. From v1.4, it uses a GPIO instead.
+ * v1.3 parts will still work, since the signal on SFRMOUT is automatic.
+ */
+static struct gpiod_lookup_table simone_spi_cs_gpio_table = {
+	.dev_id = "spi0",
+	.table = {
+		GPIO_LOOKUP("A", 1, "cs", GPIO_ACTIVE_LOW),
+		{ },
+	},
+};
+
+static struct ep93xx_spi_info simone_spi_info __initdata = {
+	.use_dma = 1,
+};
+
+static struct i2c_board_info __initdata simone_i2c_board_info[] = {
+	{
+		I2C_BOARD_INFO("ds1337", 0x68),
+	},
+};
+
+static struct platform_device simone_audio_device = {
+	.name		= "simone-audio",
+	.id		= -1,
+};
+
+static void __init simone_register_audio(void)
+{
+	ep93xx_register_ac97();
+	platform_device_register(&simone_audio_device);
+}
+
+static void __init simone_init_machine(void)
+{
+	ep93xx_init_devices();
+	ep93xx_register_flash(2, EP93XX_CS6_PHYS_BASE, SZ_8M);
+	ep93xx_register_eth(&simone_eth_data, 1);
+	ep93xx_register_fb(&simone_fb_info);
+	ep93xx_register_i2c(simone_i2c_board_info,
+			    ARRAY_SIZE(simone_i2c_board_info));
+	gpiod_add_lookup_table(&simone_mmc_spi_gpio_table);
+	gpiod_add_lookup_table(&simone_spi_cs_gpio_table);
+	ep93xx_register_spi(&simone_spi_info, simone_spi_devices,
+			    ARRAY_SIZE(simone_spi_devices));
+	simone_register_audio();
+}
+
+MACHINE_START(SIM_ONE, "Simplemachines Sim.One Board")
+	/* Maintainer: Ryan Mallon */
+	.atag_offset	= 0x100,
+	.nr_irqs	= NR_EP93XX_IRQS,
+	.map_io		= ep93xx_map_io,
+	.init_irq	= ep93xx_init_irq,
+	.init_time	= ep93xx_timer_init,
+	.init_machine	= simone_init_machine,
+	.restart	= ep93xx_restart,
+MACHINE_END