diff options
Diffstat (limited to 'drivers/net/wireless/realtek/rtlwifi/rtl8188ee/pwrseq.h')
| -rw-r--r-- | drivers/net/wireless/realtek/rtlwifi/rtl8188ee/pwrseq.h | 289 |
1 files changed, 289 insertions, 0 deletions
diff --git a/drivers/net/wireless/realtek/rtlwifi/rtl8188ee/pwrseq.h b/drivers/net/wireless/realtek/rtlwifi/rtl8188ee/pwrseq.h new file mode 100644 index 000000000..42e222c17 --- /dev/null +++ b/drivers/net/wireless/realtek/rtlwifi/rtl8188ee/pwrseq.h @@ -0,0 +1,289 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* Copyright(c) 2009-2013 Realtek Corporation.*/ + +#ifndef __RTL8723E_PWRSEQ_H__ +#define __RTL8723E_PWRSEQ_H__ + +#include "../pwrseqcmd.h" +/* Check document WM-20110607-Paul-RTL8188EE_Power_Architecture-R02.vsd + * There are 6 HW Power States: + * 0: POFF--Power Off + * 1: PDN--Power Down + * 2: CARDEMU--Card Emulation + * 3: ACT--Active Mode + * 4: LPS--Low Power State + * 5: SUS--Suspend + * + * The transision from different states are defined below + * TRANS_CARDEMU_TO_ACT + * TRANS_ACT_TO_CARDEMU + * TRANS_CARDEMU_TO_SUS + * TRANS_SUS_TO_CARDEMU + * TRANS_CARDEMU_TO_PDN + * TRANS_ACT_TO_LPS + * TRANS_LPS_TO_ACT + * + * TRANS_END + * PWR SEQ Version: rtl8188ee_PwrSeq_V09.h + */ + +#define RTL8188EE_TRANS_CARDEMU_TO_ACT_STEPS 10 +#define RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS 10 +#define RTL8188EE_TRANS_CARDEMU_TO_SUS_STEPS 10 +#define RTL8188EE_TRANS_SUS_TO_CARDEMU_STEPS 10 +#define RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS 10 +#define RTL8188EE_TRANS_PDN_TO_CARDEMU_STEPS 10 +#define RTL8188EE_TRANS_ACT_TO_LPS_STEPS 15 +#define RTL8188EE_TRANS_LPS_TO_ACT_STEPS 15 +#define RTL8188EE_TRANS_END_STEPS 1 + +/* The following macros have the following format: + * { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value + * comments }, + */ +#define RTL8188EE_TRANS_CARDEMU_TO_ACT \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1) \ + /* wait till 0x04[17] = 1 power ready*/}, \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0)|BIT(1), 0 \ + /* 0x02[1:0] = 0 reset BB*/}, \ + {0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7) \ + /*0x24[23] = 2b'01 schmit trigger */}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0 \ + /* 0x04[15] = 0 disable HWPDN (control by DRV)*/}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4)|BIT(3), 0 \ + /*0x04[12:11] = 2b'00 disable WL suspend*/}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0) \ + /*0x04[8] = 1 polling until return 0*/}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0 \ + /*wait till 0x04[8] = 0*/}, \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \ + /*LDO normal mode*/}, \ + {0x0074, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \ + /*SDIO Driving*/}, + +#define RTL8188EE_TRANS_ACT_TO_CARDEMU \ + {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ + /*0x1F[7:0] = 0 turn off RF*/}, \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \ + /*LDO Sleep mode*/}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1) \ + /*0x04[9] = 1 turn off MAC by HW state machine*/}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0 \ + /*wait till 0x04[9] = 0 polling until return 0 to disable*/}, + +#define RTL8188EE_TRANS_CARDEMU_TO_SUS \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3) \ + /*0x04[12:11] = 2b'01enable WL suspend*/}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)|BIT(4) \ + /*0x04[12:11] = 2b'11enable WL suspend for PCIe*/}, \ + {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, BIT(7) \ + /* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */},\ + {0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \ + /*Clear SIC_EN register 0x40[12] = 1'b0 */}, \ + {0xfe10, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \ + /*Set USB suspend enable local register 0xfe10[4]=1 */}, \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0) \ + /*Set SDIO suspend local register*/}, \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0 \ + /*wait power state to suspend*/}, + +#define RTL8188EE_TRANS_SUS_TO_CARDEMU \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0 \ + /*Set SDIO suspend local register*/}, \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1) \ + /*wait power state to suspend*/}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), 0 \ + /*0x04[12:11] = 2b'00 disable WL suspend*/}, + +#define RTL8188EE_TRANS_CARDEMU_TO_CARDDIS \ + {0x0026, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7) \ + /*0x24[23] = 2b'01 schmit trigger */}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT(3) \ + /*0x04[12:11] = 2b'01 enable WL suspend*/}, \ + {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ + /* 0x04[31:30] = 2b'10 enable enable bandgap mbias in suspend */},\ + {0x0041, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK|PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \ + /*Clear SIC_EN register 0x40[12] = 1'b0 */}, \ + {0xfe10, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4) \ + /*Set USB suspend enable local register 0xfe10[4]=1 */}, \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0) \ + /*Set SDIO suspend local register*/}, \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0 \ + /*wait power state to suspend*/}, + +#define RTL8188EE_TRANS_CARDDIS_TO_CARDEMU \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0 \ + /*Set SDIO suspend local register*/}, \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1) \ + /*wait power state to suspend*/}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0 \ + /*0x04[12:11] = 2b'00 disable WL suspend*/}, + +#define RTL8188EE_TRANS_CARDEMU_TO_PDN \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0/* 0x04[16] = 0*/}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7) \ + /* 0x04[15] = 1*/}, + +#define RTL8188EE_TRANS_PDN_TO_CARDEMU \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0/* 0x04[15] = 0*/}, + +#define RTL8188EE_TRANS_ACT_TO_LPS \ + {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x7F \ + /*Tx Pause*/}, \ + {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ + /*Should be zero if no packet is transmitting*/}, \ + {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ + /*Should be zero if no packet is transmitting*/}, \ + {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ + /*Should be zero if no packet is transmitting*/}, \ + {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0 \ + /*Should be zero if no packet is transmitting*/}, \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0 \ + /*CCK and OFDM are disabled,and clock are gated*/}, \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US \ + /*Delay 1us*/}, \ + {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x3F \ + /*Reset MAC TRX*/}, \ + {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0 \ + /*check if removed later*/}, \ + {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5) \ + /*Respond TxOK to scheduler*/}, + + +#define RTL8188EE_TRANS_LPS_TO_ACT \ + {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84 \ + /*SDIO RPWM*/}, \ + {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84 \ + /*USB RPWM*/}, \ + {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84 \ + /*PCIe RPWM*/}, \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS \ + /*Delay*/}, \ + {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0 \ + /*. 0x08[4] = 0 switch TSF to 40M*/}, \ + {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(7), 0 \ + /*Polling 0x109[7]=0 TSF in 40M*/}, \ + {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6)|BIT(7), 0 \ + /*. 0x29[7:6] = 2b'00 enable BB clock*/}, \ + {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1) \ + /*. 0x101[1] = 1*/}, \ + {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF \ + /*. 0x100[7:0] = 0xFF enable WMAC TRX*/}, \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1)|BIT(0), BIT(1)|BIT(0) \ + /*. 0x02[1:0] = 2b'11 enable BB macro*/}, \ + {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0 \ + /*. 0x522 = 0*/}, + +#define RTL8188EE_TRANS_END \ + {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ + 0, PWR_CMD_END, 0, 0} + +extern struct wlan_pwr_cfg rtl8188ee_power_on_flow + [RTL8188EE_TRANS_CARDEMU_TO_ACT_STEPS + + RTL8188EE_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8188ee_radio_off_flow + [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8188EE_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8188ee_card_disable_flow + [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS + + RTL8188EE_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8188ee_card_enable_flow + [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS + + RTL8188EE_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8188ee_suspend_flow + [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8188EE_TRANS_CARDEMU_TO_SUS_STEPS + + RTL8188EE_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8188ee_resume_flow + [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8188EE_TRANS_CARDEMU_TO_SUS_STEPS + + RTL8188EE_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8188ee_hwpdn_flow + [RTL8188EE_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8188EE_TRANS_CARDEMU_TO_PDN_STEPS + + RTL8188EE_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8188ee_enter_lps_flow + [RTL8188EE_TRANS_ACT_TO_LPS_STEPS + + RTL8188EE_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8188ee_leave_lps_flow + [RTL8188EE_TRANS_LPS_TO_ACT_STEPS + + RTL8188EE_TRANS_END_STEPS]; + +/* RTL8723 Power Configuration CMDs for PCIe interface */ +#define RTL8188EE_NIC_PWR_ON_FLOW rtl8188ee_power_on_flow +#define RTL8188EE_NIC_RF_OFF_FLOW rtl8188ee_radio_off_flow +#define RTL8188EE_NIC_DISABLE_FLOW rtl8188ee_card_disable_flow +#define RTL8188EE_NIC_ENABLE_FLOW rtl8188ee_card_enable_flow +#define RTL8188EE_NIC_SUSPEND_FLOW rtl8188ee_suspend_flow +#define RTL8188EE_NIC_RESUME_FLOW rtl8188ee_resume_flow +#define RTL8188EE_NIC_PDN_FLOW rtl8188ee_hwpdn_flow +#define RTL8188EE_NIC_LPS_ENTER_FLOW rtl8188ee_enter_lps_flow +#define RTL8188EE_NIC_LPS_LEAVE_FLOW rtl8188ee_leave_lps_flow + +#endif |