summaryrefslogtreecommitdiffstats
path: root/arch/arm64/boot/dts/renesas/salvator-xs.dtsi
blob: 08b925624e129205681d4e5feefee8596ddec2e1 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
// SPDX-License-Identifier: GPL-2.0
/*
 * Device Tree Source for the Salvator-X 2nd version board
 *
 * Copyright (C) 2015-2017 Renesas Electronics Corp.
 */

#include "salvator-common.dtsi"

/ {
	model = "Renesas Salvator-X 2nd version board";
	compatible = "renesas,salvator-xs";
};

&extal_clk {
	clock-frequency = <16640000>;
};

&i2c4 {
	clock-frequency = <400000>;

	versaclock6: clock-generator@6a {
		compatible = "idt,5p49v6901";
		reg = <0x6a>;
		#clock-cells = <1>;
		clocks = <&x23_clk>;
		clock-names = "xin";
	};
};

#ifdef SOC_HAS_SATA
&pca9654 {
	pcie-sata-switch-hog {
		gpio-hog;
		gpios = <7 GPIO_ACTIVE_HIGH>;
		output-low; /* enable SATA by default */
		line-name = "PCIE/SATA switch";
	};
};

/* SW12-7 must be set 'Off' (MD12 set to 1) which is not the default! */
#endif /* SOC_HAS_SATA */

#ifdef SOC_HAS_USB2_CH3
&ehci3 {
	dr_mode = "otg";
	status = "okay";
};

&hsusb3 {
	dr_mode = "otg";
	status = "okay";
};

&ohci3 {
	dr_mode = "otg";
	status = "okay";
};

&pfc {
	/*
	 * - On Salvator-X[S], GP6_3[01] are connected to ADV7482 as irq pins
	 *   (when SW31 is the default setting on Salvator-XS).
	 * - If SW31 is the default setting, you cannot use USB2.0 ch3 on
	 *   r8a77951 with Salvator-XS.
	 *   Hence the SW31 setting must be changed like 2) below.
	 *   1) Default setting of SW31: ON-ON-OFF-OFF-OFF-OFF:
	 *	- Connect GP6_3[01] to ADV7842.
	 *   2) Changed setting of SW31: OFF-OFF-ON-ON-ON-ON:
	 *	- Connect GP6_3[01] to BD082065 (USB2.0 ch3's host power).
	 *	- Connect GP6_{04,21} to ADV7842.
	 */
	usb2_ch3_pins: usb2_ch3 {
		groups = "usb2_ch3";
		function = "usb2_ch3";
	};
};

&usb2_phy3 {
	pinctrl-0 = <&usb2_ch3_pins>;
	pinctrl-names = "default";

	status = "okay";
};
#endif /* SOC_HAS_USB2_CH3 */