diff options
Diffstat (limited to 'drivers/net/wireless/realtek/rtlwifi/rtl8723be/pwrseq.h')
| -rw-r--r-- | drivers/net/wireless/realtek/rtlwifi/rtl8723be/pwrseq.h | 401 |
1 files changed, 401 insertions, 0 deletions
diff --git a/drivers/net/wireless/realtek/rtlwifi/rtl8723be/pwrseq.h b/drivers/net/wireless/realtek/rtlwifi/rtl8723be/pwrseq.h new file mode 100644 index 000000000..57eac4864 --- /dev/null +++ b/drivers/net/wireless/realtek/rtlwifi/rtl8723be/pwrseq.h @@ -0,0 +1,401 @@ +/* SPDX-License-Identifier: GPL-2.0 */ +/* Copyright(c) 2009-2014 Realtek Corporation.*/ + +#ifndef __RTL8723BE_PWRSEQ_H__ +#define __RTL8723BE_PWRSEQ_H__ + +#include "../pwrseqcmd.h" +/** + * Check document WM-20130425-JackieLau-RTL8723B_Power_Architecture v05.vsd + * There are 6 HW Power States: + * 0: POFF--Power Off + * 1: PDN--Power Down + * 2: CARDEMU--Card Emulation + * 3: ACT--Active Mode + * 4: LPS--Low Power State + * 5: SUS--Suspend + * + * The transision from different states are defined below + * TRANS_CARDEMU_TO_ACT + * TRANS_ACT_TO_CARDEMU + * TRANS_CARDEMU_TO_SUS + * TRANS_SUS_TO_CARDEMU + * TRANS_CARDEMU_TO_PDN + * TRANS_ACT_TO_LPS + * TRANS_LPS_TO_ACT + * + * TRANS_END + */ +#define RTL8723B_TRANS_CARDEMU_TO_ACT_STEPS 23 +#define RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS 15 +#define RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS 15 +#define RTL8723B_TRANS_SUS_TO_CARDEMU_STEPS 15 +#define RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS 15 +#define RTL8723B_TRANS_PDN_TO_CARDEMU_STEPS 15 +#define RTL8723B_TRANS_ACT_TO_LPS_STEPS 15 +#define RTL8723B_TRANS_LPS_TO_ACT_STEPS 15 +#define RTL8723B_TRANS_END_STEPS 1 + +#define RTL8723B_TRANS_CARDEMU_TO_ACT \ + /* format */ \ + /* comments here */ \ + /* {offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value}, */\ + /*0x20[0] = 1b'1 enable LDOA12 MACRO block for all interface*/ \ + {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, \ + /*0x67[0] = 0 to disable BT_GPS_SEL pins*/ \ + {0x0067, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, \ + /*Delay 1ms*/ \ + {0x0001, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_DELAY, 1, PWRSEQ_DELAY_MS}, \ + /*0x00[5] = 1b'0 release analog Ips to digital ,1:isolation*/ \ + {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), 0}, \ + /* disable SW LPS 0x04[10]=0 and WLSUS_EN 0x04[11]=0*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4)|BIT(3)|BIT(2)), 0}, \ + /* Disable USB suspend */ \ + {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0) , BIT(0)}, \ + /* wait till 0x04[17] = 1 power ready*/ \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), BIT(1)}, \ + /* Enable USB suspend */ \ + {0x0075, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0) , 0}, \ + /* release WLON reset 0x04[16]=1*/ \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, \ + /* disable HWPDN 0x04[15]=0*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0}, \ + /* disable WL suspend*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, (BIT(4)|BIT(3)), 0}, \ + /* polling until return 0*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(0), 0}, \ + /* Enable WL control XTAL setting*/ \ + {0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), BIT(6)}, \ + /*Enable falling edge triggering interrupt*/ \ + {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \ + /*Enable GPIO9 interrupt mode*/ \ + {0x0063, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \ + /*Enable GPIO9 input mode*/ \ + {0x0062, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0}, \ + /*Enable HSISR GPIO[C:0] interrupt*/ \ + {0x0058, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), BIT(0)}, \ + /*Enable HSISR GPIO9 interrupt*/ \ + {0x005A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \ + /*For GPIO9 internal pull high setting by test chip*/ \ + {0x0068, PWR_CUT_TESTCHIP_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK,\ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3), BIT(3)}, \ + /*For GPIO9 internal pull high setting*/ \ + {0x0069, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), BIT(6)}, + +#define RTL8723B_TRANS_ACT_TO_CARDEMU \ + /* format */ \ + /* comments here */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\ + /*0x1F[7:0] = 0 turn off RF*/ \ + {0x001F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, \ + /*0x4C[24] = 0x4F[0] = 0, */ \ + /*switch DPDT_SEL_P output from register 0x65[2] */ \ + {0x004F, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, \ + /*Enable rising edge triggering interrupt*/ \ + {0x0049, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0}, \ + /*0x04[9] = 1 turn off MAC by HW state machine*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \ + /*wait till 0x04[9] = 0 polling until return 0 to disable*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(1), 0}, \ + /* Enable BT control XTAL setting*/ \ + {0x0010, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6), 0}, \ + /*0x00[5] = 1b'1 analog Ips to digital ,1:isolation*/ \ + {0x0000, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, \ + PWR_CMD_WRITE, BIT(5), BIT(5)}, \ + /*0x20[0] = 1b'0 disable LDOA12 MACRO block*/ \ + {0x0020, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, \ + PWR_CMD_WRITE, BIT(0), 0}, + +#define RTL8723B_TRANS_CARDEMU_TO_SUS \ + /* format */ \ + /* comments here */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value },*/\ + /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4) | BIT(3), (BIT(4) | BIT(3))}, \ + /*0x04[12:11] = 2b'01 enable WL suspend*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, PWR_BASEADDR_MAC, \ + PWR_CMD_WRITE, BIT(3) | BIT(4), BIT(3)}, \ + /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, \ + /*0x07[7:0] = 0x20 SDIO SOP option to disable BG/MB/ACK/SWR*/ \ + {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, \ + /*0x04[12:11] = 2b'11 enable WL suspend for PCIe*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(4), BIT(3) | BIT(4)},\ + /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, \ + /*wait power state to suspend*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0}, + +#define RTL8723B_TRANS_SUS_TO_CARDEMU \ + /* format */ \ + /* comments here */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\ + /*clear suspend enable and power down enable*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, \ + /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0}, \ + /*wait power state to suspend*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)}, \ + /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, \ + /*0x04[12:11] = 2b'00 disable WL suspend*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, + +#define RTL8723B_TRANS_CARDEMU_TO_CARDDIS \ + /* format */ \ + /* comments here */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\ + /*0x07=0x20 , SOP option to disable BG/MB*/ \ + {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x20}, \ + /*0x04[12:11] = 2b'01 enable WL suspend*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_USB_MSK | PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), BIT(3)}, \ + /*0x04[10] = 1, enable SW LPS*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(2), BIT(2)}, \ + /*0x48[16] = 1 to enable GPIO9 as EXT WAKEUP*/ \ + {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 1}, \ + /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, \ + /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), BIT(0)}, \ + /*wait power state to suspend*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), 0}, + +#define RTL8723B_TRANS_CARDDIS_TO_CARDEMU \ + /* format */ \ + /* comments here */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\ + /*clear suspend enable and power down enable*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3) | BIT(7), 0}, \ + /*Set SDIO suspend local register*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_WRITE, BIT(0), 0}, \ + /*wait power state to suspend*/ \ + {0x0086, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_POLLING, BIT(1), BIT(1)}, \ + /*0x48[16] = 0 to disable GPIO9 as EXT WAKEUP*/ \ + {0x004A, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, \ + /*0x04[12:11] = 2b'00 disable WL suspend*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(3)|BIT(4), 0}, \ + /*0x23[4] = 1b'0 12H LDO enter normal mode*/ \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, \ + /*PCIe DMA start*/ \ + {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, + +#define RTL8723B_TRANS_CARDEMU_TO_PDN \ + /* format */ \ + /* comments here */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\ + /*0x23[4] = 1b'1 12H LDO enter sleep mode*/ \ + {0x0023, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), BIT(4)}, \ + /*0x07[7:0] = 0x20 SOP option to disable BG/MB/ACK/SWR*/ \ + {0x0007, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, \ + PWR_INTF_SDIO_MSK | PWR_INTF_USB_MSK, PWR_BASEADDR_MAC, \ + PWR_CMD_WRITE, 0xFF, 0x20}, \ + /* 0x04[16] = 0*/ \ + {0x0006, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, \ + /* 0x04[15] = 1*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), BIT(7)}, + +#define RTL8723B_TRANS_PDN_TO_CARDEMU \ + /* format */ \ + /* comments here */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\ + /* 0x04[15] = 0*/ \ + {0x0005, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(7), 0}, + +#define RTL8723B_TRANS_ACT_TO_LPS \ + /* format */ \ + /* comments here */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\ + /*PCIe DMA stop*/ \ + {0x0301, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, \ + /*Tx Pause*/ \ + {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, \ + /*Should be zero if no packet is transmitting*/ \ + {0x05F8, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0}, \ + /*Should be zero if no packet is transmitting*/ \ + {0x05F9, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0}, \ + /*Should be zero if no packet is transmitting*/ \ + {0x05FA, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0}, \ + /*Should be zero if no packet is transmitting*/ \ + {0x05FB, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, 0xFF, 0}, \ + /*CCK and OFDM are disabled,and clock are gated*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(0), 0}, \ + /*Delay 1us*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_US}, \ + /*Whole BB is reset*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0}, \ + /*Reset MAC TRX*/ \ + {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x03}, \ + /*check if removed later*/ \ + {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), 0}, \ + /*When driver enter Sus/ Disable, enable LOP for BT*/ \ + {0x0093, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x00}, \ + /*Respond TxOK to scheduler*/ \ + {0x0553, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(5), BIT(5)}, + +#define RTL8723B_TRANS_LPS_TO_ACT \ + /* format */ \ + /* comments here */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\ + /*SDIO RPWM*/ \ + {0x0080, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_SDIO_MSK, \ + PWR_BASEADDR_SDIO, PWR_CMD_WRITE, 0xFF, 0x84}, \ + /*USB RPWM*/ \ + {0xFE58, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_USB_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, \ + /*PCIe RPWM*/ \ + {0x0361, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_PCI_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0x84}, \ + /*Delay*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_DELAY, 0, PWRSEQ_DELAY_MS}, \ + /*. 0x08[4] = 0 switch TSF to 40M*/ \ + {0x0008, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(4), 0}, \ + /*Polling 0x109[7]=0 TSF in 40M*/ \ + {0x0109, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_POLLING, BIT(7), 0}, \ + /*. 0x29[7:6] = 2b'00 enable BB clock*/ \ + {0x0029, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(6)|BIT(7), 0}, \ + /*. 0x101[1] = 1*/ \ + {0x0101, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1), BIT(1)}, \ + /*. 0x100[7:0] = 0xFF enable WMAC TRX*/ \ + {0x0100, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0xFF}, \ + /*. 0x02[1:0] = 2b'11 enable BB macro*/ \ + {0x0002, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, BIT(1) | BIT(0), BIT(1) | BIT(0)}, \ + /*. 0x522 = 0*/ \ + {0x0522, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, \ + PWR_BASEADDR_MAC, PWR_CMD_WRITE, 0xFF, 0}, + +#define RTL8723B_TRANS_END \ + /* format */ \ + /* comments here */ \ + /* { offset, cut_msk, fab_msk|interface_msk, base|cmd, msk, value }, */\ + {0xFFFF, PWR_CUT_ALL_MSK, PWR_FAB_ALL_MSK, PWR_INTF_ALL_MSK, 0, \ + PWR_CMD_END, 0, 0}, + +extern struct wlan_pwr_cfg rtl8723B_power_on_flow + [RTL8723B_TRANS_CARDEMU_TO_ACT_STEPS + + RTL8723B_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8723B_radio_off_flow + [RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8723B_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8723B_card_disable_flow + [RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS + + RTL8723B_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8723B_card_enable_flow + [RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS + + RTL8723B_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8723B_suspend_flow + [RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS + + RTL8723B_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8723B_resume_flow + [RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8723B_TRANS_CARDEMU_TO_SUS_STEPS + + RTL8723B_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8723B_hwpdn_flow + [RTL8723B_TRANS_ACT_TO_CARDEMU_STEPS + + RTL8723B_TRANS_CARDEMU_TO_PDN_STEPS + + RTL8723B_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8723B_enter_lps_flow + [RTL8723B_TRANS_ACT_TO_LPS_STEPS + + RTL8723B_TRANS_END_STEPS]; +extern struct wlan_pwr_cfg rtl8723B_leave_lps_flow + [RTL8723B_TRANS_LPS_TO_ACT_STEPS + + RTL8723B_TRANS_END_STEPS]; + +/* RTL8723 Power Configuration CMDs for PCIe interface */ +#define RTL8723_NIC_PWR_ON_FLOW rtl8723B_power_on_flow +#define RTL8723_NIC_RF_OFF_FLOW rtl8723B_radio_off_flow +#define RTL8723_NIC_DISABLE_FLOW rtl8723B_card_disable_flow +#define RTL8723_NIC_ENABLE_FLOW rtl8723B_card_enable_flow +#define RTL8723_NIC_SUSPEND_FLOW rtl8723B_suspend_flow +#define RTL8723_NIC_RESUME_FLOW rtl8723B_resume_flow +#define RTL8723_NIC_PDN_FLOW rtl8723B_hwpdn_flow +#define RTL8723_NIC_LPS_ENTER_FLOW rtl8723B_enter_lps_flow +#define RTL8723_NIC_LPS_LEAVE_FLOW rtl8723B_leave_lps_flow + +#endif |