1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
|
/*------------------------------------------------------------------------
* smc9000.h
*
* Copyright (C) 1998 by Daniel Engstr�m
* Copyright (C) 1996 by Erik Stahlman
*
* This software may be used and distributed according to the terms
* of the GNU Public License, incorporated herein by reference.
*
* This file contains register information and access macros for
* the SMC91xxx chipset.
*
* Information contained in this file was obtained from the SMC91C94
* manual from SMC. To get a copy, if you really want one, you can find
* information under www.smsc.com in the components division.
* ( this thanks to advice from Donald Becker ).
*
* Authors
* Daniel Engstr�m <daniel.engstrom@riksnett.no>
* Erik Stahlman <erik@vt.edu>
*
* History
* 96-01-06 Erik Stahlman moved definitions here from main .c
* file
* 96-01-19 Erik Stahlman polished this up some, and added
* better error handling
* 98-09-25 Daniel Engstr�m adjusted for Etherboot
* 98-09-27 Daniel Engstr�m moved some static strings back to the
* main .c file
* --------------------------------------------------------------------------*/
FILE_LICENCE ( GPL_ANY );
#ifndef _SMC9000_H_
# define _SMC9000_H_
/* I want some simple types */
typedef unsigned char byte;
typedef unsigned short word;
typedef unsigned long int dword;
/*---------------------------------------------------------------
*
* A description of the SMC registers is probably in order here,
* although for details, the SMC datasheet is invaluable.
*
* Basically, the chip has 4 banks of registers ( 0 to 3 ), which
* are accessed by writing a number into the BANK_SELECT register
* ( I also use a SMC_SELECT_BANK macro for this ).
*
* The banks are configured so that for most purposes, bank 2 is all
* that is needed for simple run time tasks.
* ----------------------------------------------------------------------*/
/*
* Bank Select Register:
*
* yyyy yyyy 0000 00xx
* xx = bank number
* yyyy yyyy = 0x33, for identification purposes.
*/
#define BANK_SELECT 14
/* BANK 0 */
#define TCR 0 /* transmit control register */
#define TCR_ENABLE 0x0001 /* if this is 1, we can transmit */
#define TCR_FDUPLX 0x0800 /* receive packets sent out */
#define TCR_STP_SQET 0x1000 /* stop transmitting if Signal quality error */
#define TCR_MON_CNS 0x0400 /* monitors the carrier status */
#define TCR_PAD_ENABLE 0x0080 /* pads short packets to 64 bytes */
#define TCR_CLEAR 0 /* do NOTHING */
/* the normal settings for the TCR register : */
#define TCR_NORMAL (TCR_ENABLE | TCR_PAD_ENABLE)
#define EPH_STATUS 2
#define ES_LINK_OK 0x4000 /* is the link integrity ok ? */
#define RCR 4
#define RCR_SOFTRESET 0x8000 /* resets the chip */
#define RCR_STRIP_CRC 0x200 /* strips CRC */
#define RCR_ENABLE 0x100 /* IFF this is set, we can receive packets */
#define RCR_ALMUL 0x4 /* receive all multicast packets */
#define RCR_PROMISC 0x2 /* enable promiscuous mode */
/* the normal settings for the RCR register : */
#define RCR_NORMAL (RCR_STRIP_CRC | RCR_ENABLE)
#define RCR_CLEAR 0x0 /* set it to a base state */
#define COUNTER 6
#define MIR 8
#define MCR 10
/* 12 is reserved */
// Receive/Phy Control Register
/* BANK 0 */
#define RPC_REG 0x000A
#define RPC_SPEED 0x2000 // When 1 PHY is in 100Mbps mode.
#define RPC_DPLX 0x1000 // When 1 PHY is in Full-Duplex Mode
#define RPC_ANEG 0x0800 // When 1 PHY is in Auto-Negotiate Mode
#define RPC_LSXA_SHFT 5 // Bits to shift LS2A,LS1A,LS0A to lsb
#define RPC_LSXB_SHFT 2 // Bits to get LS2B,LS1B,LS0B to lsb
#define RPC_LED_100_10 (0x00) // LED = 100Mbps OR's with 10Mbps link detect
#define RPC_LED_RES (0x01) // LED = Reserved
#define RPC_LED_10 (0x02) // LED = 10Mbps link detect
#define RPC_LED_FD (0x03) // LED = Full Duplex Mode
#define RPC_LED_TX_RX (0x04) // LED = TX or RX packet occurred
#define RPC_LED_100 (0x05) // LED = 100Mbps link dectect
#define RPC_LED_TX (0x06) // LED = TX packet occurred
#define RPC_LED_RX (0x07) // LED = RX packet occurred
#define RPC_DEFAULT (RPC_ANEG | (RPC_LED_100 << RPC_LSXA_SHFT) | (RPC_LED_FD << RPC_LSXB_SHFT) | RPC_SPEED | RPC_DPLX)
// Receive/Phy Control Register
/* BANK 0 */
#define RPC_REG 0x000A
#define RPC_SPEED 0x2000 // When 1 PHY is in 100Mbps mode.
#define RPC_DPLX 0x1000 // When 1 PHY is in Full-Duplex Mode
#define RPC_ANEG 0x0800 // When 1 PHY is in Auto-Negotiate Mode
#define RPC_LSXA_SHFT 5 // Bits to shift LS2A,LS1A,LS0A to lsb
#define RPC_LSXB_SHFT 2 // Bits to get LS2B,LS1B,LS0B to lsb
#define RPC_LED_100_10 (0x00) // LED = 100Mbps OR's with 10Mbps link detect
#define RPC_LED_RES (0x01) // LED = Reserved
#define RPC_LED_10 (0x02) // LED = 10Mbps link detect
#define RPC_LED_FD (0x03) // LED = Full Duplex Mode
#define RPC_LED_TX_RX (0x04) // LED = TX or RX packet occurred
#define RPC_LED_100 (0x05) // LED = 100Mbps link dectect
#define RPC_LED_TX (0x06) // LED = TX packet occurred
#define RPC_LED_RX (0x07) // LED = RX packet occurred
#define RPC_DEFAULT (RPC_ANEG | (RPC_LED_100 << RPC_LSXA_SHFT) | (RPC_LED_FD << RPC_LSXB_SHFT) | RPC_SPEED | RPC_DPLX)
/* BANK 1 */
#define CONFIG 0
#define CFG_AUI_SELECT 0x100
#define BASE 2
#define ADDR0 4
#define ADDR1 6
#define ADDR2 8
#define GENERAL 10
#define CONTROL 12
#define CTL_POWERDOWN 0x2000
#define CTL_LE_ENABLE 0x80
#define CTL_CR_ENABLE 0x40
#define CTL_TE_ENABLE 0x0020
#define CTL_AUTO_RELEASE 0x0800
#define CTL_EPROM_ACCESS 0x0003 /* high if Eprom is being read */
/* BANK 2 */
#define MMU_CMD 0
#define MC_BUSY 1 /* only readable bit in the register */
#define MC_NOP 0
#define MC_ALLOC 0x20 /* or with number of 256 byte packets */
#define MC_RESET 0x40
#define MC_REMOVE 0x60 /* remove the current rx packet */
#define MC_RELEASE 0x80 /* remove and release the current rx packet */
#define MC_FREEPKT 0xA0 /* Release packet in PNR register */
#define MC_ENQUEUE 0xC0 /* Enqueue the packet for transmit */
#define PNR_ARR 2
#define FIFO_PORTS 4
#define FP_RXEMPTY 0x8000
#define FP_TXEMPTY 0x80
#define POINTER 6
#define PTR_READ 0x2000
#define PTR_RCV 0x8000
#define PTR_AUTOINC 0x4000
#define PTR_AUTO_INC 0x0040
#define DATA_1 8
#define DATA_2 10
#define INTERRUPT 12
#define INT_MASK 13
#define IM_RCV_INT 0x1
#define IM_TX_INT 0x2
#define IM_TX_EMPTY_INT 0x4
#define IM_ALLOC_INT 0x8
#define IM_RX_OVRN_INT 0x10
#define IM_EPH_INT 0x20
#define IM_ERCV_INT 0x40 /* not on SMC9192 */
/* BANK 3 */
#define MULTICAST1 0
#define MULTICAST2 2
#define MULTICAST3 4
#define MULTICAST4 6
#define MGMT 8
#define REVISION 10 /* ( hi: chip id low: rev # ) */
// Management Interface Register (MII)
#define MII_REG 0x0008
#define MII_MSK_CRS100 0x4000 // Disables CRS100 detection during tx half dup
#define MII_MDOE 0x0008 // MII Output Enable
#define MII_MCLK 0x0004 // MII Clock, pin MDCLK
#define MII_MDI 0x0002 // MII Input, pin MDI
#define MII_MDO 0x0001 // MII Output, pin MDO
/* this is NOT on SMC9192 */
#define ERCV 12
/* Note that 9194 and 9196 have the smame chip id,
* the 9196 will have revisions starting at 6 */
#define CHIP_9190 3
#define CHIP_9194 4
#define CHIP_9195 5
#define CHIP_9196 4
#define CHIP_91100 7
#define CHIP_91100FD 8
#define REV_9196 6
/*
* Transmit status bits
*/
#define TS_SUCCESS 0x0001
#define TS_LOSTCAR 0x0400
#define TS_LATCOL 0x0200
#define TS_16COL 0x0010
/*
* Receive status bits
*/
#define RS_ALGNERR 0x8000
#define RS_BADCRC 0x2000
#define RS_ODDFRAME 0x1000
#define RS_TOOLONG 0x0800
#define RS_TOOSHORT 0x0400
#define RS_MULTICAST 0x0001
#define RS_ERRORS (RS_ALGNERR | RS_BADCRC | RS_TOOLONG | RS_TOOSHORT)
// PHY Register Addresses (LAN91C111 Internal PHY)
// PHY Control Register
#define PHY_CNTL_REG 0x00
#define PHY_CNTL_RST 0x8000 // 1=PHY Reset
#define PHY_CNTL_LPBK 0x4000 // 1=PHY Loopback
#define PHY_CNTL_SPEED 0x2000 // 1=100Mbps, 0=10Mpbs
#define PHY_CNTL_ANEG_EN 0x1000 // 1=Enable Auto negotiation
#define PHY_CNTL_PDN 0x0800 // 1=PHY Power Down mode
#define PHY_CNTL_MII_DIS 0x0400 // 1=MII 4 bit interface disabled
#define PHY_CNTL_ANEG_RST 0x0200 // 1=Reset Auto negotiate
#define PHY_CNTL_DPLX 0x0100 // 1=Full Duplex, 0=Half Duplex
#define PHY_CNTL_COLTST 0x0080 // 1= MII Colision Test
// PHY Status Register
#define PHY_STAT_REG 0x01
#define PHY_STAT_CAP_T4 0x8000 // 1=100Base-T4 capable
#define PHY_STAT_CAP_TXF 0x4000 // 1=100Base-X full duplex capable
#define PHY_STAT_CAP_TXH 0x2000 // 1=100Base-X half duplex capable
#define PHY_STAT_CAP_TF 0x1000 // 1=10Mbps full duplex capable
#define PHY_STAT_CAP_TH 0x0800 // 1=10Mbps half duplex capable
#define PHY_STAT_CAP_SUPR 0x0040 // 1=recv mgmt frames with not preamble
#define PHY_STAT_ANEG_ACK 0x0020 // 1=ANEG has completed
#define PHY_STAT_REM_FLT 0x0010 // 1=Remote Fault detected
#define PHY_STAT_CAP_ANEG 0x0008 // 1=Auto negotiate capable
#define PHY_STAT_LINK 0x0004 // 1=valid link
#define PHY_STAT_JAB 0x0002 // 1=10Mbps jabber condition
#define PHY_STAT_EXREG 0x0001 // 1=extended registers implemented
// PHY Identifier Registers
#define PHY_ID1_REG 0x02 // PHY Identifier 1
#define PHY_ID2_REG 0x03 // PHY Identifier 2
// PHY Auto-Negotiation Advertisement Register
#define PHY_AD_REG 0x04
#define PHY_AD_NP 0x8000 // 1=PHY requests exchange of Next Page
#define PHY_AD_ACK 0x4000 // 1=got link code word from remote
#define PHY_AD_RF 0x2000 // 1=advertise remote fault
#define PHY_AD_T4 0x0200 // 1=PHY is capable of 100Base-T4
#define PHY_AD_TX_FDX 0x0100 // 1=PHY is capable of 100Base-TX FDPLX
#define PHY_AD_TX_HDX 0x0080 // 1=PHY is capable of 100Base-TX HDPLX
#define PHY_AD_10_FDX 0x0040 // 1=PHY is capable of 10Base-T FDPLX
#define PHY_AD_10_HDX 0x0020 // 1=PHY is capable of 10Base-T HDPLX
#define PHY_AD_CSMA 0x0001 // 1=PHY is capable of 802.3 CMSA
// PHY Auto-negotiation Remote End Capability Register
#define PHY_RMT_REG 0x05
// Uses same bit definitions as PHY_AD_REG
// PHY Configuration Register 1
#define PHY_CFG1_REG 0x10
#define PHY_CFG1_LNKDIS 0x8000 // 1=Rx Link Detect Function disabled
#define PHY_CFG1_XMTDIS 0x4000 // 1=TP Transmitter Disabled
#define PHY_CFG1_XMTPDN 0x2000 // 1=TP Transmitter Powered Down
#define PHY_CFG1_BYPSCR 0x0400 // 1=Bypass scrambler/descrambler
#define PHY_CFG1_UNSCDS 0x0200 // 1=Unscramble Idle Reception Disable
#define PHY_CFG1_EQLZR 0x0100 // 1=Rx Equalizer Disabled
#define PHY_CFG1_CABLE 0x0080 // 1=STP(150ohm), 0=UTP(100ohm)
#define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db
#define PHY_CFG1_TLVL_SHIFT 2 // Transmit Output Level Adjust
#define PHY_CFG1_TLVL_MASK 0x003C
#define PHY_CFG1_TRF_MASK 0x0003 // Transmitter Rise/Fall time
// PHY Configuration Register 2
#define PHY_CFG2_REG 0x11
#define PHY_CFG2_APOLDIS 0x0020 // 1=Auto Polarity Correction disabled
#define PHY_CFG2_JABDIS 0x0010 // 1=Jabber disabled
#define PHY_CFG2_MREG 0x0008 // 1=Multiple register access (MII mgt)
#define PHY_CFG2_INTMDIO 0x0004 // 1=Interrupt signaled with MDIO pulseo
// PHY Status Output (and Interrupt status) Register
#define PHY_INT_REG 0x12 // Status Output (Interrupt Status)
#define PHY_INT_INT 0x8000 // 1=bits have changed since last read
#define PHY_INT_LNKFAIL 0x4000 // 1=Link Not detected
#define PHY_INT_LOSSSYNC 0x2000 // 1=Descrambler has lost sync
#define PHY_INT_CWRD 0x1000 // 1=Invalid 4B5B code detected on rx
#define PHY_INT_SSD 0x0800 // 1=No Start Of Stream detected on rx
#define PHY_INT_ESD 0x0400 // 1=No End Of Stream detected on rx
#define PHY_INT_RPOL 0x0200 // 1=Reverse Polarity detected
#define PHY_INT_JAB 0x0100 // 1=Jabber detected
#define PHY_INT_SPDDET 0x0080 // 1=100Base-TX mode, 0=10Base-T mode
#define PHY_INT_DPLXDET 0x0040 // 1=Device in Full Duplex
// PHY Interrupt/Status Mask Register
#define PHY_MASK_REG 0x13 // Interrupt Mask
// Uses the same bit definitions as PHY_INT_REG
// PHY Register Addresses (LAN91C111 Internal PHY)
// PHY Control Register
#define PHY_CNTL_REG 0x00
#define PHY_CNTL_RST 0x8000 // 1=PHY Reset
#define PHY_CNTL_LPBK 0x4000 // 1=PHY Loopback
#define PHY_CNTL_SPEED 0x2000 // 1=100Mbps, 0=10Mpbs
#define PHY_CNTL_ANEG_EN 0x1000 // 1=Enable Auto negotiation
#define PHY_CNTL_PDN 0x0800 // 1=PHY Power Down mode
#define PHY_CNTL_MII_DIS 0x0400 // 1=MII 4 bit interface disabled
#define PHY_CNTL_ANEG_RST 0x0200 // 1=Reset Auto negotiate
#define PHY_CNTL_DPLX 0x0100 // 1=Full Duplex, 0=Half Duplex
#define PHY_CNTL_COLTST 0x0080 // 1= MII Colision Test
// PHY Status Register
#define PHY_STAT_REG 0x01
#define PHY_STAT_CAP_T4 0x8000 // 1=100Base-T4 capable
#define PHY_STAT_CAP_TXF 0x4000 // 1=100Base-X full duplex capable
#define PHY_STAT_CAP_TXH 0x2000 // 1=100Base-X half duplex capable
#define PHY_STAT_CAP_TF 0x1000 // 1=10Mbps full duplex capable
#define PHY_STAT_CAP_TH 0x0800 // 1=10Mbps half duplex capable
#define PHY_STAT_CAP_SUPR 0x0040 // 1=recv mgmt frames with not preamble
#define PHY_STAT_ANEG_ACK 0x0020 // 1=ANEG has completed
#define PHY_STAT_REM_FLT 0x0010 // 1=Remote Fault detected
#define PHY_STAT_CAP_ANEG 0x0008 // 1=Auto negotiate capable
#define PHY_STAT_LINK 0x0004 // 1=valid link
#define PHY_STAT_JAB 0x0002 // 1=10Mbps jabber condition
#define PHY_STAT_EXREG 0x0001 // 1=extended registers implemented
// PHY Identifier Registers
#define PHY_ID1_REG 0x02 // PHY Identifier 1
#define PHY_ID2_REG 0x03 // PHY Identifier 2
// PHY Auto-Negotiation Advertisement Register
#define PHY_AD_REG 0x04
#define PHY_AD_NP 0x8000 // 1=PHY requests exchange of Next Page
#define PHY_AD_ACK 0x4000 // 1=got link code word from remote
#define PHY_AD_RF 0x2000 // 1=advertise remote fault
#define PHY_AD_T4 0x0200 // 1=PHY is capable of 100Base-T4
#define PHY_AD_TX_FDX 0x0100 // 1=PHY is capable of 100Base-TX FDPLX
#define PHY_AD_TX_HDX 0x0080 // 1=PHY is capable of 100Base-TX HDPLX
#define PHY_AD_10_FDX 0x0040 // 1=PHY is capable of 10Base-T FDPLX
#define PHY_AD_10_HDX 0x0020 // 1=PHY is capable of 10Base-T HDPLX
#define PHY_AD_CSMA 0x0001 // 1=PHY is capable of 802.3 CMSA
// PHY Auto-negotiation Remote End Capability Register
#define PHY_RMT_REG 0x05
// Uses same bit definitions as PHY_AD_REG
// PHY Configuration Register 1
#define PHY_CFG1_REG 0x10
#define PHY_CFG1_LNKDIS 0x8000 // 1=Rx Link Detect Function disabled
#define PHY_CFG1_XMTDIS 0x4000 // 1=TP Transmitter Disabled
#define PHY_CFG1_XMTPDN 0x2000 // 1=TP Transmitter Powered Down
#define PHY_CFG1_BYPSCR 0x0400 // 1=Bypass scrambler/descrambler
#define PHY_CFG1_UNSCDS 0x0200 // 1=Unscramble Idle Reception Disable
#define PHY_CFG1_EQLZR 0x0100 // 1=Rx Equalizer Disabled
#define PHY_CFG1_CABLE 0x0080 // 1=STP(150ohm), 0=UTP(100ohm)
#define PHY_CFG1_RLVL0 0x0040 // 1=Rx Squelch level reduced by 4.5db
#define PHY_CFG1_TLVL_SHIFT 2 // Transmit Output Level Adjust
#define PHY_CFG1_TLVL_MASK 0x003C
#define PHY_CFG1_TRF_MASK 0x0003 // Transmitter Rise/Fall time
// PHY Configuration Register 2
#define PHY_CFG2_REG 0x11
#define PHY_CFG2_APOLDIS 0x0020 // 1=Auto Polarity Correction disabled
#define PHY_CFG2_JABDIS 0x0010 // 1=Jabber disabled
#define PHY_CFG2_MREG 0x0008 // 1=Multiple register access (MII mgt)
#define PHY_CFG2_INTMDIO 0x0004 // 1=Interrupt signaled with MDIO pulseo
// PHY Status Output (and Interrupt status) Register
#define PHY_INT_REG 0x12 // Status Output (Interrupt Status)
#define PHY_INT_INT 0x8000 // 1=bits have changed since last read
#define PHY_INT_LNKFAIL 0x4000 // 1=Link Not detected
#define PHY_INT_LOSSSYNC 0x2000 // 1=Descrambler has lost sync
#define PHY_INT_CWRD 0x1000 // 1=Invalid 4B5B code detected on rx
#define PHY_INT_SSD 0x0800 // 1=No Start Of Stream detected on rx
#define PHY_INT_ESD 0x0400 // 1=No End Of Stream detected on rx
#define PHY_INT_RPOL 0x0200 // 1=Reverse Polarity detected
#define PHY_INT_JAB 0x0100 // 1=Jabber detected
#define PHY_INT_SPDDET 0x0080 // 1=100Base-TX mode, 0=10Base-T mode
#define PHY_INT_DPLXDET 0x0040 // 1=Device in Full Duplex
// PHY Interrupt/Status Mask Register
#define PHY_MASK_REG 0x13 // Interrupt Mask
// Uses the same bit definitions as PHY_INT_REG
/*-------------------------------------------------------------------------
* I define some macros to make it easier to do somewhat common
* or slightly complicated, repeated tasks.
--------------------------------------------------------------------------*/
/* select a register bank, 0 to 3 */
#define SMC_SELECT_BANK(x, y) { _outw( y, x + BANK_SELECT ); }
/* define a small delay for the reset */
#define SMC_DELAY(x) { inw( x + RCR );\
inw( x + RCR );\
inw( x + RCR ); }
#endif /* _SMC_9000_H_ */
|
