Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 99 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/net/xilinx_axienet.txt b/Documentation/devicetree/bindings/net/xilinx_axienet.txt
new file mode 100644
index 000000000..1aa4c6006
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/xilinx_axienet.txt
@@ -0,0 +1,99 @@
+XILINX AXI ETHERNET Device Tree Bindings
+--------------------------------------------------------
+
+Also called  AXI 1G/2.5G Ethernet Subsystem, the xilinx axi ethernet IP core
+provides connectivity to an external ethernet PHY supporting different
+interfaces: MII, GMII, RGMII, SGMII, 1000BaseX. It also includes two
+segments of memory for buffering TX and RX, as well as the capability of
+offloading TX/RX checksum calculation off the processor.
+
+Management configuration is done through the AXI interface, while payload is
+sent and received through means of an AXI DMA controller. This driver
+includes the DMA driver code, so this driver is incompatible with AXI DMA
+driver.
+
+For more details about mdio please refer phy.txt file in the same directory.
+
+Required properties:
+- compatible	: Must be one of "xlnx,axi-ethernet-1.00.a",
+		  "xlnx,axi-ethernet-1.01.a", "xlnx,axi-ethernet-2.01.a"
+- reg		: Address and length of the IO space, as well as the address
+                  and length of the AXI DMA controller IO space, unless
+                  axistream-connected is specified, in which case the reg
+                  attribute of the node referenced by it is used.
+- interrupts	: Should be a list of 2 or 3 interrupts: TX DMA, RX DMA,
+		  and optionally Ethernet core. If axistream-connected is
+		  specified, the TX/RX DMA interrupts should be on that node
+		  instead, and only the Ethernet core interrupt is optionally
+		  specified here.
+- phy-handle	: Should point to the external phy device if exists. Pointing
+		  this to the PCS/PMA PHY is deprecated and should be avoided.
+		  See ethernet.txt file in the same directory.
+- xlnx,rxmem	: Set to allocated memory buffer for Rx/Tx in the hardware
+
+Optional properties:
+- phy-mode	: See ethernet.txt
+- xlnx,phy-type	: Deprecated, do not use, but still accepted in preference
+		  to phy-mode.
+- xlnx,txcsum	: 0 or empty for disabling TX checksum offload,
+		  1 to enable partial TX checksum offload,
+		  2 to enable full TX checksum offload
+- xlnx,rxcsum	: Same values as xlnx,txcsum but for RX checksum offload
+- xlnx,switch-x-sgmii : Boolean to indicate the Ethernet core is configured to
+		  support both 1000BaseX and SGMII modes. If set, the phy-mode
+		  should be set to match the mode selected on core reset (i.e.
+		  by the basex_or_sgmii core input line).
+- clock-names: 	  Tuple listing input clock names. Possible clocks:
+		  s_axi_lite_clk: Clock for AXI register slave interface
+		  axis_clk: AXI4-Stream clock for TXD RXD TXC and RXS interfaces
+		  ref_clk: Ethernet reference clock, used by signal delay
+			   primitives and transceivers
+		  mgt_clk: MGT reference clock (used by optional internal
+			   PCS/PMA PHY)
+
+		  Note that if s_axi_lite_clk is not specified by name, the
+		  first clock of any name is used for this. If that is also not
+		  specified, the clock rate is auto-detected from the CPU clock
+		  (but only on platforms where this is possible). New device
+		  trees should specify all applicable clocks by name - the
+		  fallbacks to an unnamed clock or to CPU clock are only for
+		  backward compatibility.
+- clocks: 	  Phandles to input clocks matching clock-names. Refer to common
+		  clock bindings.
+- axistream-connected: Reference to another node which contains the resources
+		       for the AXI DMA controller used by this device.
+		       If this is specified, the DMA-related resources from that
+		       device (DMA registers and DMA TX/RX interrupts) rather
+		       than this one will be used.
+ - mdio		: Child node for MDIO bus. Must be defined if PHY access is
+		  required through the core's MDIO interface (i.e. always,
+		  unless the PHY is accessed through a different bus).
+
+ - pcs-handle: 	  Phandle to the internal PCS/PMA PHY in SGMII or 1000Base-X
+		  modes, where "pcs-handle" should be used to point
+		  to the PCS/PMA PHY, and "phy-handle" should point to an
+		  external PHY if exists.
+
+Example:
+	axi_ethernet_eth: ethernet@40c00000 {
+		compatible = "xlnx,axi-ethernet-1.00.a";
+		device_type = "network";
+		interrupt-parent = <&microblaze_0_axi_intc>;
+		interrupts = <2 0 1>;
+		clock-names = "s_axi_lite_clk", "axis_clk", "ref_clk", "mgt_clk";
+		clocks = <&axi_clk>, <&axi_clk>, <&pl_enet_ref_clk>, <&mgt_clk>;
+		phy-mode = "mii";
+		reg = <0x40c00000 0x40000 0x50c00000 0x40000>;
+		xlnx,rxcsum = <0x2>;
+		xlnx,rxmem = <0x800>;
+		xlnx,txcsum = <0x2>;
+		phy-handle = <&phy0>;
+		axi_ethernetlite_0_mdio: mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			phy0: phy@0 {
+				device_type = "ethernet-phy";
+				reg = <1>;
+			};
+		};
+	};