Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 102 insertions, 0 deletions

diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt
new file mode 100644
index 000000000..8147e3e3e
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/ti-pci.txt
@@ -0,0 +1,102 @@
+TI PCI Controllers
+
+PCIe DesignWare Controller
+ - compatible: Should be "ti,dra7-pcie" for RC (deprecated)
+	       Should be "ti,dra7-pcie-ep" for EP (deprecated)
+	       Should be "ti,dra746-pcie-rc" for dra74x/dra76 in RC mode
+	       Should be "ti,dra746-pcie-ep" for dra74x/dra76 in EP mode
+	       Should be "ti,dra726-pcie-rc" for dra72x in RC mode
+	       Should be "ti,dra726-pcie-ep" for dra72x in EP mode
+ - phys : list of PHY specifiers (used by generic PHY framework)
+ - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the
+	       number of PHYs as specified in *phys* property.
+ - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
+	       where <X> is the instance number of the pcie from the HW spec.
+ - num-lanes as specified in ../snps,dw-pcie.yaml
+ - ti,syscon-lane-sel : phandle/offset pair. Phandle to the system control
+			module and the register offset to specify lane
+			selection.
+
+HOST MODE
+=========
+ - reg : Two register ranges as listed in the reg-names property
+ - reg-names : The first entry must be "ti-conf" for the TI-specific registers
+	       The second entry must be "rc-dbics" for the DesignWare PCIe
+	       registers
+	       The third entry must be "config" for the PCIe configuration space
+ - interrupts : Two interrupt entries must be specified. The first one is for
+		main interrupt line and the second for MSI interrupt line.
+ - #address-cells,
+   #size-cells,
+   #interrupt-cells,
+   device_type,
+   ranges,
+   interrupt-map-mask,
+   interrupt-map : as specified in ../snps,dw-pcie.yaml
+ - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument
+			       should contain the register offset within syscon
+			       and the 2nd argument should contain the bit field
+			       for setting the bit to enable unaligned
+			       access.
+
+DEVICE MODE
+===========
+ - reg : Four register ranges as listed in the reg-names property
+ - reg-names : "ti-conf" for the TI-specific registers
+	       "ep_dbics" for the standard configuration registers as
+		they are locally accessed within the DIF CS space
+	       "ep_dbics2" for the standard configuration registers as
+		they are locally accessed within the DIF CS2 space
+	       "addr_space" used to map remote RC address space
+ - interrupts : one interrupt entries must be specified for main interrupt.
+ - num-ib-windows : number of inbound address translation windows
+ - num-ob-windows : number of outbound address translation windows
+ - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument
+			       should contain the register offset within syscon
+			       and the 2nd argument should contain the bit field
+			       for setting the bit to enable unaligned
+			       access.
+
+Optional Property:
+ - gpios : Should be added if a GPIO line is required to drive PERST# line
+
+NOTE: Two DT nodes may be added for each PCI controller; one for host
+mode and another for device mode. So in order for PCI to
+work in host mode, EP mode DT node should be disabled and in order to PCI to
+work in EP mode, host mode DT node should be disabled. Host mode and EP
+mode are mutually exclusive.
+
+Example:
+axi {
+	compatible = "simple-bus";
+	#size-cells = <1>;
+	#address-cells = <1>;
+	ranges = <0x51000000 0x51000000 0x3000
+		  0x0	     0x20000000 0x10000000>;
+	pcie@51000000 {
+		compatible = "ti,dra7-pcie";
+		reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>;
+		reg-names = "rc_dbics", "ti_conf", "config";
+		interrupts = <0 232 0x4>, <0 233 0x4>;
+		#address-cells = <3>;
+		#size-cells = <2>;
+		device_type = "pci";
+		ranges = <0x81000000 0 0          0x03000 0 0x00010000
+			  0x82000000 0 0x20013000 0x13000 0 0xffed000>;
+		#interrupt-cells = <1>;
+		num-lanes = <1>;
+		ti,hwmods = "pcie1";
+		phys = <&pcie1_phy>;
+		phy-names = "pcie-phy0";
+		interrupt-map-mask = <0 0 0 7>;
+		interrupt-map = <0 0 0 1 &pcie_intc 1>,
+				<0 0 0 2 &pcie_intc 2>,
+				<0 0 0 3 &pcie_intc 3>,
+				<0 0 0 4 &pcie_intc 4>;
+		pcie_intc: interrupt-controller {
+			interrupt-controller;
+			#address-cells = <0>;
+			#interrupt-cells = <1>;
+		};
+	};
+};