Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 221 insertions, 0 deletions

diff --git a/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi
new file mode 100644
index 000000000..002663d75
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/sc7180-trogdor-lazor.dtsi
@@ -0,0 +1,221 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Google Lazor board device tree source
+ *
+ * Copyright 2020 Google LLC.
+ */
+
+/* This file must be included after sc7180-trogdor.dtsi */
+#include <arm/cros-ec-keyboard.dtsi>
+
+&ap_sar_sensor {
+	semtech,cs0-ground;
+	semtech,combined-sensors = <3>;
+	semtech,resolution = "fine";
+	semtech,startup-sensor = <0>;
+	semtech,proxraw-strength = <8>;
+	semtech,avg-pos-strength = <64>;
+};
+
+&ap_tp_i2c {
+	status = "okay";
+};
+
+/*
+ * Lazor is stuffed with a 47k NTC as charger thermistor which currently is
+ * not supported by the PM6150 ADC driver. Disable the charger thermal zone
+ * to avoid using bogus temperature values.
+ */
+&charger_thermal {
+	status = "disabled";
+};
+
+ap_ts_pen_1v8: &i2c4 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	ap_ts: touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_int_l>, <&ts_reset_l>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
+
+		post-power-on-delay-ms = <20>;
+		hid-descr-addr = <0x0001>;
+
+		vdd-supply = <&pp3300_ts>;
+	};
+};
+
+&panel {
+	compatible = "boe,nv133fhm-n62";
+};
+
+&pm6150_adc {
+	/delete-node/ charger-thermistor@4f;
+};
+
+&pm6150_adc_tm {
+	status = "disabled";
+
+	/delete-node/ charger-thermistor@0;
+};
+
+&trackpad {
+	interrupts = <58 IRQ_TYPE_EDGE_FALLING>;
+};
+
+&wifi {
+	qcom,ath10k-calibration-variant = "GO_LAZOR";
+};
+
+/* PINCTRL - modifications to sc7180-trogdor.dtsi */
+
+&trackpad_int_1v8_odl {
+	pinmux {
+		pins = "gpio58";
+	};
+
+	pinconf {
+		pins = "gpio58";
+	};
+};
+
+&ts_reset_l {
+	pinconf {
+		/* This pin is not connected on -rev0, pull up to park. */
+		/delete-property/bias-disable;
+		bias-pull-up;
+	};
+};
+
+/* PINCTRL - board-specific pinctrl */
+
+&tlmm {
+	gpio-line-names = "ESIM_MISO",
+			  "ESIM_MOSI",
+			  "ESIM_CLK",
+			  "ESIM_CS_L",
+			  "",
+			  "",
+			  "AP_TP_I2C_SDA",
+			  "AP_TP_I2C_SCL",
+			  "TS_RESET_L",
+			  "TS_INT_L",
+			  "",
+			  "EDP_BRIJ_IRQ",
+			  "AP_EDP_BKLTEN",
+			  "AP_RAM_ID2",
+			  "",
+			  "EDP_BRIJ_I2C_SDA",
+			  "EDP_BRIJ_I2C_SCL",
+			  "HUB_RST_L",
+			  "",
+			  "AP_RAM_ID1",
+			  "AP_SKU_ID2",
+			  "",
+			  "",
+			  "AMP_EN",
+			  "P_SENSOR_INT_L",
+			  "AP_SAR_SENSOR_SDA",
+			  "AP_SAR_SENSOR_SCL",
+			  "",
+			  "HP_IRQ",
+			  "AP_RAM_ID0",
+			  "EN_PP3300_DX_EDP",
+			  "AP_BRD_ID2",
+			  "BRIJ_SUSPEND",
+			  "AP_BRD_ID0",
+			  "AP_H1_SPI_MISO",
+			  "AP_H1_SPI_MOSI",
+			  "AP_H1_SPI_CLK",
+			  "AP_H1_SPI_CS_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "H1_AP_INT_ODL",
+			  "",
+			  "UART_AP_TX_DBG_RX",
+			  "UART_DBG_TX_AP_RX",
+			  "HP_I2C_SDA",
+			  "HP_I2C_SCL",
+			  "FORCED_USB_BOOT",
+			  "",
+			  "",
+			  "AMP_DIN",
+			  "",
+			  "HP_BCLK",
+			  "HP_LRCLK",
+			  "HP_DOUT",
+			  "HP_DIN",
+			  "HP_MCLK",
+			  "TRACKPAD_INT_1V8_ODL",
+			  "AP_EC_SPI_MISO",
+			  "AP_EC_SPI_MOSI",
+			  "AP_EC_SPI_CLK",
+			  "AP_EC_SPI_CS_L",
+			  "AP_SPI_CLK",
+			  "AP_SPI_MOSI",
+			  "AP_SPI_MISO",
+			  /*
+			   * AP_FLASH_WP_L is crossystem ABI. Schematics
+			   * call it BIOS_FLASH_WP_L.
+			   */
+			  "AP_FLASH_WP_L",
+			  "DBG_SPI_HOLD_L",
+			  "AP_SPI_CS0_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "UIM2_DATA",
+			  "UIM2_CLK",
+			  "UIM2_RST",
+			  "UIM2_PRESENT",
+			  "UIM1_DATA",
+			  "UIM1_CLK",
+			  "UIM1_RST",
+			  "",
+			  "EN_PP3300_CODEC",
+			  "EN_PP3300_HUB",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_SKU_ID1",
+			  "AP_RST_REQ",
+			  "",
+			  "AP_BRD_ID1",
+			  "AP_EC_INT_L",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "EDP_BRIJ_EN",
+			  "AP_SKU_ID0",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "",
+			  "AP_TS_PEN_I2C_SDA",
+			  "AP_TS_PEN_I2C_SCL",
+			  "DP_HOT_PLUG_DET",
+			  "EC_IN_RW_ODL";
+};