Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 87 insertions, 0 deletions

diff --git a/drivers/net/ethernet/wiznet/Kconfig b/drivers/net/ethernet/wiznet/Kconfig
new file mode 100644
index 000000000..4bac2ad2d
--- /dev/null
+++ b/drivers/net/ethernet/wiznet/Kconfig
@@ -0,0 +1,87 @@
+# SPDX-License-Identifier: GPL-2.0-only
+#
+# WIZnet devices configuration
+#
+
+config NET_VENDOR_WIZNET
+	bool "WIZnet devices"
+	depends on HAS_IOMEM
+	default y
+	help
+	  If you have a network (Ethernet) card belonging to this class, say Y.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about WIZnet devices. If you say Y, you will be asked
+	  for your specific card in the following questions.
+
+if NET_VENDOR_WIZNET
+
+config WIZNET_W5100
+	tristate "WIZnet W5100 Ethernet support"
+	depends on HAS_IOMEM
+	help
+	  Support for WIZnet W5100 chips.
+
+	  W5100 is a single chip with integrated 10/100 Ethernet MAC,
+	  PHY and hardware TCP/IP stack, but this driver is limited to
+	  the MAC and PHY functions only, onchip TCP/IP is unused.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called w5100.
+
+config WIZNET_W5300
+	tristate "WIZnet W5300 Ethernet support"
+	depends on HAS_IOMEM
+	help
+	  Support for WIZnet W5300 chips.
+
+	  W5300 is a single chip with integrated 10/100 Ethernet MAC,
+	  PHY and hardware TCP/IP stack, but this driver is limited to
+	  the MAC and PHY functions only, onchip TCP/IP is unused.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called w5300.
+
+choice
+	prompt "WIZnet interface mode"
+	depends on WIZNET_W5100 || WIZNET_W5300
+	default WIZNET_BUS_ANY
+
+config WIZNET_BUS_DIRECT
+	bool "Direct address bus mode"
+	help
+	  In direct address mode host system can directly access all registers
+	  after mapping to Memory-Mapped I/O space.
+
+config WIZNET_BUS_INDIRECT
+	bool "Indirect address bus mode"
+	help
+	  In indirect address mode host system indirectly accesses registers
+	  using Indirect Mode Address Register and Indirect Mode Data Register,
+	  which are directly mapped to Memory-Mapped I/O space.
+
+config WIZNET_BUS_ANY
+	bool "Select interface mode in runtime"
+	help
+	  If interface mode is unknown in compile time, it can be selected
+	  in runtime from board/platform resources configuration.
+
+	  Performance may decrease compared to explicitly selected bus mode.
+endchoice
+
+config WIZNET_W5100_SPI
+	tristate "WIZnet W5100/W5200/W5500 Ethernet support for SPI mode"
+	depends on WIZNET_BUS_ANY && WIZNET_W5100
+	depends on SPI
+	help
+	  In SPI mode host system accesses registers using SPI protocol
+	  (mode 0) on the SPI bus.
+
+	  Performance decreases compared to other bus interface mode.
+	  In W5100 SPI mode, burst READ/WRITE processing are not provided.
+
+	  To compile this driver as a module, choose M here: the module
+	  will be called w5100-spi.
+
+endif # NET_VENDOR_WIZNET