Adding upstream version 6.1.76.upstream/6.1.76upstream

Signed-off-by: Daniel Baumann <daniel.baumann@progress-linux.org>

1 files changed, 948 insertions, 0 deletions

diff --git a/drivers/tty/serial/sa1100.c b/drivers/tty/serial/sa1100.c
new file mode 100644
index 000000000..dd9e3253c
--- /dev/null
+++ b/drivers/tty/serial/sa1100.c
@@ -0,0 +1,948 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ *  Driver for SA11x0 serial ports
+ *
+ *  Based on drivers/char/serial.c, by Linus Torvalds, Theodore Ts'o.
+ *
+ *  Copyright (C) 2000 Deep Blue Solutions Ltd.
+ */
+
+#include <linux/module.h>
+#include <linux/ioport.h>
+#include <linux/init.h>
+#include <linux/console.h>
+#include <linux/sysrq.h>
+#include <linux/platform_data/sa11x0-serial.h>
+#include <linux/platform_device.h>
+#include <linux/tty.h>
+#include <linux/tty_flip.h>
+#include <linux/serial_core.h>
+#include <linux/serial.h>
+#include <linux/io.h>
+
+#include <asm/irq.h>
+#include <mach/hardware.h>
+#include <mach/irqs.h>
+
+#include "serial_mctrl_gpio.h"
+
+/* We've been assigned a range on the "Low-density serial ports" major */
+#define SERIAL_SA1100_MAJOR	204
+#define MINOR_START		5
+
+#define NR_PORTS		3
+
+#define SA1100_ISR_PASS_LIMIT	256
+
+/*
+ * Convert from ignore_status_mask or read_status_mask to UTSR[01]
+ */
+#define SM_TO_UTSR0(x)	((x) & 0xff)
+#define SM_TO_UTSR1(x)	((x) >> 8)
+#define UTSR0_TO_SM(x)	((x))
+#define UTSR1_TO_SM(x)	((x) << 8)
+
+#define UART_GET_UTCR0(sport)	__raw_readl((sport)->port.membase + UTCR0)
+#define UART_GET_UTCR1(sport)	__raw_readl((sport)->port.membase + UTCR1)
+#define UART_GET_UTCR2(sport)	__raw_readl((sport)->port.membase + UTCR2)
+#define UART_GET_UTCR3(sport)	__raw_readl((sport)->port.membase + UTCR3)
+#define UART_GET_UTSR0(sport)	__raw_readl((sport)->port.membase + UTSR0)
+#define UART_GET_UTSR1(sport)	__raw_readl((sport)->port.membase + UTSR1)
+#define UART_GET_CHAR(sport)	__raw_readl((sport)->port.membase + UTDR)
+
+#define UART_PUT_UTCR0(sport,v)	__raw_writel((v),(sport)->port.membase + UTCR0)
+#define UART_PUT_UTCR1(sport,v)	__raw_writel((v),(sport)->port.membase + UTCR1)
+#define UART_PUT_UTCR2(sport,v)	__raw_writel((v),(sport)->port.membase + UTCR2)
+#define UART_PUT_UTCR3(sport,v)	__raw_writel((v),(sport)->port.membase + UTCR3)
+#define UART_PUT_UTSR0(sport,v)	__raw_writel((v),(sport)->port.membase + UTSR0)
+#define UART_PUT_UTSR1(sport,v)	__raw_writel((v),(sport)->port.membase + UTSR1)
+#define UART_PUT_CHAR(sport,v)	__raw_writel((v),(sport)->port.membase + UTDR)
+
+/*
+ * This is the size of our serial port register set.
+ */
+#define UART_PORT_SIZE	0x24
+
+/*
+ * This determines how often we check the modem status signals
+ * for any change.  They generally aren't connected to an IRQ
+ * so we have to poll them.  We also check immediately before
+ * filling the TX fifo incase CTS has been dropped.
+ */
+#define MCTRL_TIMEOUT	(250*HZ/1000)
+
+struct sa1100_port {
+	struct uart_port	port;
+	struct timer_list	timer;
+	unsigned int		old_status;
+	struct mctrl_gpios	*gpios;
+};
+
+/*
+ * Handle any change of modem status signal since we were last called.
+ */
+static void sa1100_mctrl_check(struct sa1100_port *sport)
+{
+	unsigned int status, changed;
+
+	status = sport->port.ops->get_mctrl(&sport->port);
+	changed = status ^ sport->old_status;
+
+	if (changed == 0)
+		return;
+
+	sport->old_status = status;
+
+	if (changed & TIOCM_RI)
+		sport->port.icount.rng++;
+	if (changed & TIOCM_DSR)
+		sport->port.icount.dsr++;
+	if (changed & TIOCM_CAR)
+		uart_handle_dcd_change(&sport->port, status & TIOCM_CAR);
+	if (changed & TIOCM_CTS)
+		uart_handle_cts_change(&sport->port, status & TIOCM_CTS);
+
+	wake_up_interruptible(&sport->port.state->port.delta_msr_wait);
+}
+
+/*
+ * This is our per-port timeout handler, for checking the
+ * modem status signals.
+ */
+static void sa1100_timeout(struct timer_list *t)
+{
+	struct sa1100_port *sport = from_timer(sport, t, timer);
+	unsigned long flags;
+
+	if (sport->port.state) {
+		spin_lock_irqsave(&sport->port.lock, flags);
+		sa1100_mctrl_check(sport);
+		spin_unlock_irqrestore(&sport->port.lock, flags);
+
+		mod_timer(&sport->timer, jiffies + MCTRL_TIMEOUT);
+	}
+}
+
+/*
+ * interrupts disabled on entry
+ */
+static void sa1100_stop_tx(struct uart_port *port)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+	u32 utcr3;
+
+	utcr3 = UART_GET_UTCR3(sport);
+	UART_PUT_UTCR3(sport, utcr3 & ~UTCR3_TIE);
+	sport->port.read_status_mask &= ~UTSR0_TO_SM(UTSR0_TFS);
+}
+
+/*
+ * port locked and interrupts disabled
+ */
+static void sa1100_start_tx(struct uart_port *port)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+	u32 utcr3;
+
+	utcr3 = UART_GET_UTCR3(sport);
+	sport->port.read_status_mask |= UTSR0_TO_SM(UTSR0_TFS);
+	UART_PUT_UTCR3(sport, utcr3 | UTCR3_TIE);
+}
+
+/*
+ * Interrupts enabled
+ */
+static void sa1100_stop_rx(struct uart_port *port)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+	u32 utcr3;
+
+	utcr3 = UART_GET_UTCR3(sport);
+	UART_PUT_UTCR3(sport, utcr3 & ~UTCR3_RIE);
+}
+
+/*
+ * Set the modem control timer to fire immediately.
+ */
+static void sa1100_enable_ms(struct uart_port *port)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+
+	mod_timer(&sport->timer, jiffies);
+
+	mctrl_gpio_enable_ms(sport->gpios);
+}
+
+static void
+sa1100_rx_chars(struct sa1100_port *sport)
+{
+	unsigned int status, ch, flg;
+
+	status = UTSR1_TO_SM(UART_GET_UTSR1(sport)) |
+		 UTSR0_TO_SM(UART_GET_UTSR0(sport));
+	while (status & UTSR1_TO_SM(UTSR1_RNE)) {
+		ch = UART_GET_CHAR(sport);
+
+		sport->port.icount.rx++;
+
+		flg = TTY_NORMAL;
+
+		/*
+		 * note that the error handling code is
+		 * out of the main execution path
+		 */
+		if (status & UTSR1_TO_SM(UTSR1_PRE | UTSR1_FRE | UTSR1_ROR)) {
+			if (status & UTSR1_TO_SM(UTSR1_PRE))
+				sport->port.icount.parity++;
+			else if (status & UTSR1_TO_SM(UTSR1_FRE))
+				sport->port.icount.frame++;
+			if (status & UTSR1_TO_SM(UTSR1_ROR))
+				sport->port.icount.overrun++;
+
+			status &= sport->port.read_status_mask;
+
+			if (status & UTSR1_TO_SM(UTSR1_PRE))
+				flg = TTY_PARITY;
+			else if (status & UTSR1_TO_SM(UTSR1_FRE))
+				flg = TTY_FRAME;
+
+			sport->port.sysrq = 0;
+		}
+
+		if (uart_handle_sysrq_char(&sport->port, ch))
+			goto ignore_char;
+
+		uart_insert_char(&sport->port, status, UTSR1_TO_SM(UTSR1_ROR), ch, flg);
+
+	ignore_char:
+		status = UTSR1_TO_SM(UART_GET_UTSR1(sport)) |
+			 UTSR0_TO_SM(UART_GET_UTSR0(sport));
+	}
+
+	tty_flip_buffer_push(&sport->port.state->port);
+}
+
+static void sa1100_tx_chars(struct sa1100_port *sport)
+{
+	struct circ_buf *xmit = &sport->port.state->xmit;
+
+	if (sport->port.x_char) {
+		UART_PUT_CHAR(sport, sport->port.x_char);
+		sport->port.icount.tx++;
+		sport->port.x_char = 0;
+		return;
+	}
+
+	/*
+	 * Check the modem control lines before
+	 * transmitting anything.
+	 */
+	sa1100_mctrl_check(sport);
+
+	if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) {
+		sa1100_stop_tx(&sport->port);
+		return;
+	}
+
+	/*
+	 * Tried using FIFO (not checking TNF) for fifo fill:
+	 * still had the '4 bytes repeated' problem.
+	 */
+	while (UART_GET_UTSR1(sport) & UTSR1_TNF) {
+		UART_PUT_CHAR(sport, xmit->buf[xmit->tail]);
+		xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
+		sport->port.icount.tx++;
+		if (uart_circ_empty(xmit))
+			break;
+	}
+
+	if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
+		uart_write_wakeup(&sport->port);
+
+	if (uart_circ_empty(xmit))
+		sa1100_stop_tx(&sport->port);
+}
+
+static irqreturn_t sa1100_int(int irq, void *dev_id)
+{
+	struct sa1100_port *sport = dev_id;
+	unsigned int status, pass_counter = 0;
+
+	spin_lock(&sport->port.lock);
+	status = UART_GET_UTSR0(sport);
+	status &= SM_TO_UTSR0(sport->port.read_status_mask) | ~UTSR0_TFS;
+	do {
+		if (status & (UTSR0_RFS | UTSR0_RID)) {
+			/* Clear the receiver idle bit, if set */
+			if (status & UTSR0_RID)
+				UART_PUT_UTSR0(sport, UTSR0_RID);
+			sa1100_rx_chars(sport);
+		}
+
+		/* Clear the relevant break bits */
+		if (status & (UTSR0_RBB | UTSR0_REB))
+			UART_PUT_UTSR0(sport, status & (UTSR0_RBB | UTSR0_REB));
+
+		if (status & UTSR0_RBB)
+			sport->port.icount.brk++;
+
+		if (status & UTSR0_REB)
+			uart_handle_break(&sport->port);
+
+		if (status & UTSR0_TFS)
+			sa1100_tx_chars(sport);
+		if (pass_counter++ > SA1100_ISR_PASS_LIMIT)
+			break;
+		status = UART_GET_UTSR0(sport);
+		status &= SM_TO_UTSR0(sport->port.read_status_mask) |
+			  ~UTSR0_TFS;
+	} while (status & (UTSR0_TFS | UTSR0_RFS | UTSR0_RID));
+	spin_unlock(&sport->port.lock);
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * Return TIOCSER_TEMT when transmitter is not busy.
+ */
+static unsigned int sa1100_tx_empty(struct uart_port *port)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+
+	return UART_GET_UTSR1(sport) & UTSR1_TBY ? 0 : TIOCSER_TEMT;
+}
+
+static unsigned int sa1100_get_mctrl(struct uart_port *port)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+	int ret = TIOCM_CTS | TIOCM_DSR | TIOCM_CAR;
+
+	mctrl_gpio_get(sport->gpios, &ret);
+
+	return ret;
+}
+
+static void sa1100_set_mctrl(struct uart_port *port, unsigned int mctrl)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+
+	mctrl_gpio_set(sport->gpios, mctrl);
+}
+
+/*
+ * Interrupts always disabled.
+ */
+static void sa1100_break_ctl(struct uart_port *port, int break_state)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+	unsigned long flags;
+	unsigned int utcr3;
+
+	spin_lock_irqsave(&sport->port.lock, flags);
+	utcr3 = UART_GET_UTCR3(sport);
+	if (break_state == -1)
+		utcr3 |= UTCR3_BRK;
+	else
+		utcr3 &= ~UTCR3_BRK;
+	UART_PUT_UTCR3(sport, utcr3);
+	spin_unlock_irqrestore(&sport->port.lock, flags);
+}
+
+static int sa1100_startup(struct uart_port *port)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+	int retval;
+
+	/*
+	 * Allocate the IRQ
+	 */
+	retval = request_irq(sport->port.irq, sa1100_int, 0,
+			     "sa11x0-uart", sport);
+	if (retval)
+		return retval;
+
+	/*
+	 * Finally, clear and enable interrupts
+	 */
+	UART_PUT_UTSR0(sport, -1);
+	UART_PUT_UTCR3(sport, UTCR3_RXE | UTCR3_TXE | UTCR3_RIE);
+
+	/*
+	 * Enable modem status interrupts
+	 */
+	spin_lock_irq(&sport->port.lock);
+	sa1100_enable_ms(&sport->port);
+	spin_unlock_irq(&sport->port.lock);
+
+	return 0;
+}
+
+static void sa1100_shutdown(struct uart_port *port)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+
+	/*
+	 * Stop our timer.
+	 */
+	del_timer_sync(&sport->timer);
+
+	/*
+	 * Free the interrupt
+	 */
+	free_irq(sport->port.irq, sport);
+
+	/*
+	 * Disable all interrupts, port and break condition.
+	 */
+	UART_PUT_UTCR3(sport, 0);
+}
+
+static void
+sa1100_set_termios(struct uart_port *port, struct ktermios *termios,
+		   const struct ktermios *old)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+	unsigned long flags;
+	unsigned int utcr0, old_utcr3, baud, quot;
+	unsigned int old_csize = old ? old->c_cflag & CSIZE : CS8;
+
+	/*
+	 * We only support CS7 and CS8.
+	 */
+	while ((termios->c_cflag & CSIZE) != CS7 &&
+	       (termios->c_cflag & CSIZE) != CS8) {
+		termios->c_cflag &= ~CSIZE;
+		termios->c_cflag |= old_csize;
+		old_csize = CS8;
+	}
+
+	if ((termios->c_cflag & CSIZE) == CS8)
+		utcr0 = UTCR0_DSS;
+	else
+		utcr0 = 0;
+
+	if (termios->c_cflag & CSTOPB)
+		utcr0 |= UTCR0_SBS;
+	if (termios->c_cflag & PARENB) {
+		utcr0 |= UTCR0_PE;
+		if (!(termios->c_cflag & PARODD))
+			utcr0 |= UTCR0_OES;
+	}
+
+	/*
+	 * Ask the core to calculate the divisor for us.
+	 */
+	baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/16); 
+	quot = uart_get_divisor(port, baud);
+
+	del_timer_sync(&sport->timer);
+
+	spin_lock_irqsave(&sport->port.lock, flags);
+
+	sport->port.read_status_mask &= UTSR0_TO_SM(UTSR0_TFS);
+	sport->port.read_status_mask |= UTSR1_TO_SM(UTSR1_ROR);
+	if (termios->c_iflag & INPCK)
+		sport->port.read_status_mask |=
+				UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE);
+	if (termios->c_iflag & (BRKINT | PARMRK))
+		sport->port.read_status_mask |=
+				UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB);
+
+	/*
+	 * Characters to ignore
+	 */
+	sport->port.ignore_status_mask = 0;
+	if (termios->c_iflag & IGNPAR)
+		sport->port.ignore_status_mask |=
+				UTSR1_TO_SM(UTSR1_FRE | UTSR1_PRE);
+	if (termios->c_iflag & IGNBRK) {
+		sport->port.ignore_status_mask |=
+				UTSR0_TO_SM(UTSR0_RBB | UTSR0_REB);
+		/*
+		 * If we're ignoring parity and break indicators,
+		 * ignore overruns too (for real raw support).
+		 */
+		if (termios->c_iflag & IGNPAR)
+			sport->port.ignore_status_mask |=
+				UTSR1_TO_SM(UTSR1_ROR);
+	}
+
+	/*
+	 * Update the per-port timeout.
+	 */
+	uart_update_timeout(port, termios->c_cflag, baud);
+
+	/*
+	 * disable interrupts and drain transmitter
+	 */
+	old_utcr3 = UART_GET_UTCR3(sport);
+	UART_PUT_UTCR3(sport, old_utcr3 & ~(UTCR3_RIE | UTCR3_TIE));
+
+	while (UART_GET_UTSR1(sport) & UTSR1_TBY)
+		barrier();
+
+	/* then, disable everything */
+	UART_PUT_UTCR3(sport, 0);
+
+	/* set the parity, stop bits and data size */
+	UART_PUT_UTCR0(sport, utcr0);
+
+	/* set the baud rate */
+	quot -= 1;
+	UART_PUT_UTCR1(sport, ((quot & 0xf00) >> 8));
+	UART_PUT_UTCR2(sport, (quot & 0xff));
+
+	UART_PUT_UTSR0(sport, -1);
+
+	UART_PUT_UTCR3(sport, old_utcr3);
+
+	if (UART_ENABLE_MS(&sport->port, termios->c_cflag))
+		sa1100_enable_ms(&sport->port);
+
+	spin_unlock_irqrestore(&sport->port.lock, flags);
+}
+
+static const char *sa1100_type(struct uart_port *port)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+
+	return sport->port.type == PORT_SA1100 ? "SA1100" : NULL;
+}
+
+/*
+ * Release the memory region(s) being used by 'port'.
+ */
+static void sa1100_release_port(struct uart_port *port)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+
+	release_mem_region(sport->port.mapbase, UART_PORT_SIZE);
+}
+
+/*
+ * Request the memory region(s) being used by 'port'.
+ */
+static int sa1100_request_port(struct uart_port *port)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+
+	return request_mem_region(sport->port.mapbase, UART_PORT_SIZE,
+			"sa11x0-uart") != NULL ? 0 : -EBUSY;
+}
+
+/*
+ * Configure/autoconfigure the port.
+ */
+static void sa1100_config_port(struct uart_port *port, int flags)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+
+	if (flags & UART_CONFIG_TYPE &&
+	    sa1100_request_port(&sport->port) == 0)
+		sport->port.type = PORT_SA1100;
+}
+
+/*
+ * Verify the new serial_struct (for TIOCSSERIAL).
+ * The only change we allow are to the flags and type, and
+ * even then only between PORT_SA1100 and PORT_UNKNOWN
+ */
+static int
+sa1100_verify_port(struct uart_port *port, struct serial_struct *ser)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+	int ret = 0;
+
+	if (ser->type != PORT_UNKNOWN && ser->type != PORT_SA1100)
+		ret = -EINVAL;
+	if (sport->port.irq != ser->irq)
+		ret = -EINVAL;
+	if (ser->io_type != SERIAL_IO_MEM)
+		ret = -EINVAL;
+	if (sport->port.uartclk / 16 != ser->baud_base)
+		ret = -EINVAL;
+	if ((void *)sport->port.mapbase != ser->iomem_base)
+		ret = -EINVAL;
+	if (sport->port.iobase != ser->port)
+		ret = -EINVAL;
+	if (ser->hub6 != 0)
+		ret = -EINVAL;
+	return ret;
+}
+
+static struct uart_ops sa1100_pops = {
+	.tx_empty	= sa1100_tx_empty,
+	.set_mctrl	= sa1100_set_mctrl,
+	.get_mctrl	= sa1100_get_mctrl,
+	.stop_tx	= sa1100_stop_tx,
+	.start_tx	= sa1100_start_tx,
+	.stop_rx	= sa1100_stop_rx,
+	.enable_ms	= sa1100_enable_ms,
+	.break_ctl	= sa1100_break_ctl,
+	.startup	= sa1100_startup,
+	.shutdown	= sa1100_shutdown,
+	.set_termios	= sa1100_set_termios,
+	.type		= sa1100_type,
+	.release_port	= sa1100_release_port,
+	.request_port	= sa1100_request_port,
+	.config_port	= sa1100_config_port,
+	.verify_port	= sa1100_verify_port,
+};
+
+static struct sa1100_port sa1100_ports[NR_PORTS];
+
+/*
+ * Setup the SA1100 serial ports.  Note that we don't include the IrDA
+ * port here since we have our own SIR/FIR driver (see drivers/net/irda)
+ *
+ * Note also that we support "console=ttySAx" where "x" is either 0 or 1.
+ * Which serial port this ends up being depends on the machine you're
+ * running this kernel on.  I'm not convinced that this is a good idea,
+ * but that's the way it traditionally works.
+ *
+ * Note that NanoEngine UART3 becomes UART2, and UART2 is no longer
+ * used here.
+ */
+static void __init sa1100_init_ports(void)
+{
+	static int first = 1;
+	int i;
+
+	if (!first)
+		return;
+	first = 0;
+
+	for (i = 0; i < NR_PORTS; i++) {
+		sa1100_ports[i].port.uartclk   = 3686400;
+		sa1100_ports[i].port.ops       = &sa1100_pops;
+		sa1100_ports[i].port.fifosize  = 8;
+		sa1100_ports[i].port.line      = i;
+		sa1100_ports[i].port.iotype    = UPIO_MEM;
+		timer_setup(&sa1100_ports[i].timer, sa1100_timeout, 0);
+	}
+
+	/*
+	 * make transmit lines outputs, so that when the port
+	 * is closed, the output is in the MARK state.
+	 */
+	PPDR |= PPC_TXD1 | PPC_TXD3;
+	PPSR |= PPC_TXD1 | PPC_TXD3;
+}
+
+void sa1100_register_uart_fns(struct sa1100_port_fns *fns)
+{
+	if (fns->get_mctrl)
+		sa1100_pops.get_mctrl = fns->get_mctrl;
+	if (fns->set_mctrl)
+		sa1100_pops.set_mctrl = fns->set_mctrl;
+
+	sa1100_pops.pm       = fns->pm;
+	/*
+	 * FIXME: fns->set_wake is unused - this should be called from
+	 * the suspend() callback if device_may_wakeup(dev)) is set.
+	 */
+}
+
+void __init sa1100_register_uart(int idx, int port)
+{
+	if (idx >= NR_PORTS) {
+		printk(KERN_ERR "%s: bad index number %d\n", __func__, idx);
+		return;
+	}
+
+	switch (port) {
+	case 1:
+		sa1100_ports[idx].port.membase = (void __iomem *)&Ser1UTCR0;
+		sa1100_ports[idx].port.mapbase = _Ser1UTCR0;
+		sa1100_ports[idx].port.irq     = IRQ_Ser1UART;
+		sa1100_ports[idx].port.flags   = UPF_BOOT_AUTOCONF;
+		break;
+
+	case 2:
+		sa1100_ports[idx].port.membase = (void __iomem *)&Ser2UTCR0;
+		sa1100_ports[idx].port.mapbase = _Ser2UTCR0;
+		sa1100_ports[idx].port.irq     = IRQ_Ser2ICP;
+		sa1100_ports[idx].port.flags   = UPF_BOOT_AUTOCONF;
+		break;
+
+	case 3:
+		sa1100_ports[idx].port.membase = (void __iomem *)&Ser3UTCR0;
+		sa1100_ports[idx].port.mapbase = _Ser3UTCR0;
+		sa1100_ports[idx].port.irq     = IRQ_Ser3UART;
+		sa1100_ports[idx].port.flags   = UPF_BOOT_AUTOCONF;
+		break;
+
+	default:
+		printk(KERN_ERR "%s: bad port number %d\n", __func__, port);
+	}
+}
+
+
+#ifdef CONFIG_SERIAL_SA1100_CONSOLE
+static void sa1100_console_putchar(struct uart_port *port, unsigned char ch)
+{
+	struct sa1100_port *sport =
+		container_of(port, struct sa1100_port, port);
+
+	while (!(UART_GET_UTSR1(sport) & UTSR1_TNF))
+		barrier();
+	UART_PUT_CHAR(sport, ch);
+}
+
+/*
+ * Interrupts are disabled on entering
+ */
+static void
+sa1100_console_write(struct console *co, const char *s, unsigned int count)
+{
+	struct sa1100_port *sport = &sa1100_ports[co->index];
+	unsigned int old_utcr3, status;
+
+	/*
+	 *	First, save UTCR3 and then disable interrupts
+	 */
+	old_utcr3 = UART_GET_UTCR3(sport);
+	UART_PUT_UTCR3(sport, (old_utcr3 & ~(UTCR3_RIE | UTCR3_TIE)) |
+				UTCR3_TXE);
+
+	uart_console_write(&sport->port, s, count, sa1100_console_putchar);
+
+	/*
+	 *	Finally, wait for transmitter to become empty
+	 *	and restore UTCR3
+	 */
+	do {
+		status = UART_GET_UTSR1(sport);
+	} while (status & UTSR1_TBY);
+	UART_PUT_UTCR3(sport, old_utcr3);
+}
+
+/*
+ * If the port was already initialised (eg, by a boot loader),
+ * try to determine the current setup.
+ */
+static void __init
+sa1100_console_get_options(struct sa1100_port *sport, int *baud,
+			   int *parity, int *bits)
+{
+	unsigned int utcr3;
+
+	utcr3 = UART_GET_UTCR3(sport) & (UTCR3_RXE | UTCR3_TXE);
+	if (utcr3 == (UTCR3_RXE | UTCR3_TXE)) {
+		/* ok, the port was enabled */
+		unsigned int utcr0, quot;
+
+		utcr0 = UART_GET_UTCR0(sport);
+
+		*parity = 'n';
+		if (utcr0 & UTCR0_PE) {
+			if (utcr0 & UTCR0_OES)
+				*parity = 'e';
+			else
+				*parity = 'o';
+		}
+
+		if (utcr0 & UTCR0_DSS)
+			*bits = 8;
+		else
+			*bits = 7;
+
+		quot = UART_GET_UTCR2(sport) | UART_GET_UTCR1(sport) << 8;
+		quot &= 0xfff;
+		*baud = sport->port.uartclk / (16 * (quot + 1));
+	}
+}
+
+static int __init
+sa1100_console_setup(struct console *co, char *options)
+{
+	struct sa1100_port *sport;
+	int baud = 9600;
+	int bits = 8;
+	int parity = 'n';
+	int flow = 'n';
+
+	/*
+	 * Check whether an invalid uart number has been specified, and
+	 * if so, search for the first available port that does have
+	 * console support.
+	 */
+	if (co->index == -1 || co->index >= NR_PORTS)
+		co->index = 0;
+	sport = &sa1100_ports[co->index];
+
+	if (options)
+		uart_parse_options(options, &baud, &parity, &bits, &flow);
+	else
+		sa1100_console_get_options(sport, &baud, &parity, &bits);
+
+	return uart_set_options(&sport->port, co, baud, parity, bits, flow);
+}
+
+static struct uart_driver sa1100_reg;
+static struct console sa1100_console = {
+	.name		= "ttySA",
+	.write		= sa1100_console_write,
+	.device		= uart_console_device,
+	.setup		= sa1100_console_setup,
+	.flags		= CON_PRINTBUFFER,
+	.index		= -1,
+	.data		= &sa1100_reg,
+};
+
+static int __init sa1100_rs_console_init(void)
+{
+	sa1100_init_ports();
+	register_console(&sa1100_console);
+	return 0;
+}
+console_initcall(sa1100_rs_console_init);
+
+#define SA1100_CONSOLE	&sa1100_console
+#else
+#define SA1100_CONSOLE	NULL
+#endif
+
+static struct uart_driver sa1100_reg = {
+	.owner			= THIS_MODULE,
+	.driver_name		= "ttySA",
+	.dev_name		= "ttySA",
+	.major			= SERIAL_SA1100_MAJOR,
+	.minor			= MINOR_START,
+	.nr			= NR_PORTS,
+	.cons			= SA1100_CONSOLE,
+};
+
+static int sa1100_serial_suspend(struct platform_device *dev, pm_message_t state)
+{
+	struct sa1100_port *sport = platform_get_drvdata(dev);
+
+	if (sport)
+		uart_suspend_port(&sa1100_reg, &sport->port);
+
+	return 0;
+}
+
+static int sa1100_serial_resume(struct platform_device *dev)
+{
+	struct sa1100_port *sport = platform_get_drvdata(dev);
+
+	if (sport)
+		uart_resume_port(&sa1100_reg, &sport->port);
+
+	return 0;
+}
+
+static int sa1100_serial_add_one_port(struct sa1100_port *sport, struct platform_device *dev)
+{
+	sport->port.dev = &dev->dev;
+	sport->port.has_sysrq = IS_ENABLED(CONFIG_SERIAL_SA1100_CONSOLE);
+
+	// mctrl_gpio_init() requires that the GPIO driver supports interrupts,
+	// but we need to support GPIO drivers for hardware that has no such
+	// interrupts.  Use mctrl_gpio_init_noauto() instead.
+	sport->gpios = mctrl_gpio_init_noauto(sport->port.dev, 0);
+	if (IS_ERR(sport->gpios)) {
+		int err = PTR_ERR(sport->gpios);
+
+		dev_err(sport->port.dev, "failed to get mctrl gpios: %d\n",
+			err);
+
+		if (err == -EPROBE_DEFER)
+			return err;
+
+		sport->gpios = NULL;
+	}
+
+	platform_set_drvdata(dev, sport);
+
+	return uart_add_one_port(&sa1100_reg, &sport->port);
+}
+
+static int sa1100_serial_probe(struct platform_device *dev)
+{
+	struct resource *res;
+	int i;
+
+	res = platform_get_resource(dev, IORESOURCE_MEM, 0);
+	if (!res)
+		return -EINVAL;
+
+	for (i = 0; i < NR_PORTS; i++)
+		if (sa1100_ports[i].port.mapbase == res->start)
+			break;
+	if (i == NR_PORTS)
+		return -ENODEV;
+
+	sa1100_serial_add_one_port(&sa1100_ports[i], dev);
+
+	return 0;
+}
+
+static int sa1100_serial_remove(struct platform_device *pdev)
+{
+	struct sa1100_port *sport = platform_get_drvdata(pdev);
+
+	if (sport)
+		uart_remove_one_port(&sa1100_reg, &sport->port);
+
+	return 0;
+}
+
+static struct platform_driver sa11x0_serial_driver = {
+	.probe		= sa1100_serial_probe,
+	.remove		= sa1100_serial_remove,
+	.suspend	= sa1100_serial_suspend,
+	.resume		= sa1100_serial_resume,
+	.driver		= {
+		.name	= "sa11x0-uart",
+	},
+};
+
+static int __init sa1100_serial_init(void)
+{
+	int ret;
+
+	printk(KERN_INFO "Serial: SA11x0 driver\n");
+
+	sa1100_init_ports();
+
+	ret = uart_register_driver(&sa1100_reg);
+	if (ret == 0) {
+		ret = platform_driver_register(&sa11x0_serial_driver);
+		if (ret)
+			uart_unregister_driver(&sa1100_reg);
+	}
+	return ret;
+}
+
+static void __exit sa1100_serial_exit(void)
+{
+	platform_driver_unregister(&sa11x0_serial_driver);
+	uart_unregister_driver(&sa1100_reg);
+}
+
+module_init(sa1100_serial_init);
+module_exit(sa1100_serial_exit);
+
+MODULE_AUTHOR("Deep Blue Solutions Ltd");
+MODULE_DESCRIPTION("SA1100 generic serial port driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS_CHARDEV_MAJOR(SERIAL_SA1100_MAJOR);
+MODULE_ALIAS("platform:sa11x0-uart");