diff options
Diffstat (limited to 'Documentation/devicetree/bindings/clock/st')
5 files changed, 321 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt new file mode 100644 index 000000000..9a46cb1d7 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt @@ -0,0 +1,32 @@ +Binding for a ST multiplexed clock driver. + +This binding supports only simple indexed multiplexers, it does not +support table based parent index to hardware value translations. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: + +- compatible : shall be: + "st,stih407-clkgen-a9-mux" + +- #clock-cells : from common clock binding; shall be set to 0. + +- reg : A Base address and length of the register set. + +- clocks : from common clock binding + +Example: + + clk_m_a9: clk-m-a9@92b0000 { + #clock-cells = <0>; + compatible = "st,stih407-clkgen-a9-mux"; + reg = <0x92b0000 0x10000>; + + clocks = <&clockgen_a9_pll 0>, + <&clockgen_a9_pll 0>, + <&clk_s_c0_flexgen 13>, + <&clk_m_a9_ext2f_div2>; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt new file mode 100644 index 000000000..d0fa1e02d --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt @@ -0,0 +1,40 @@ +Binding for a ST pll clock driver. + +This binding uses the common clock binding[1]. +Base address is located to the parent node. See clock binding[2] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[2] Documentation/devicetree/bindings/clock/st/st,clkgen.txt + +Required properties: + +- compatible : shall be: + "st,clkgen-pll0" + "st,clkgen-pll0-a0" + "st,clkgen-pll0-c0" + "st,clkgen-pll1" + "st,clkgen-pll1-c0" + "st,stih407-clkgen-plla9" + "st,stih418-clkgen-plla9" + +- #clock-cells : From common clock binding; shall be set to 1. + +- clocks : From common clock binding + +- clock-output-names : From common clock binding. + +Example: + + clockgen-a9@92b0000 { + compatible = "st,clkgen-c32"; + reg = <0x92b0000 0xffff>; + + clockgen_a9_pll: clockgen-a9-pll { + #clock-cells = <1>; + compatible = "st,stih407-clkgen-plla9"; + + clocks = <&clk_sysin>; + + clock-output-names = "clockgen-a9-pll-odf"; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,clkgen.txt b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt new file mode 100644 index 000000000..45ac19bfa --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,clkgen.txt @@ -0,0 +1,68 @@ +Binding for a Clockgen hardware block found on +certain STMicroelectronics consumer electronics SoC devices. + +A Clockgen node can contain pll, diviser or multiplexer nodes. + +We will find only the base address of the Clockgen, this base +address is common of all subnode. + + clockgen_node { + reg = <>; + + pll_node { + ... + }; + + quadfs_node { + ... + }; + + mux_node { + ... + }; + + flexgen_node { + ... + }; + ... + }; + +This binding uses the common clock binding[1]. +Each subnode should use the binding described in [2]..[7] + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt +[3] Documentation/devicetree/bindings/clock/st/st,clkgen-mux.txt +[4] Documentation/devicetree/bindings/clock/st/st,clkgen-pll.txt +[7] Documentation/devicetree/bindings/clock/st/st,quadfs.txt +[8] Documentation/devicetree/bindings/clock/st/st,flexgen.txt + + +Required properties: +- reg : A Base address and length of the register set. + +Example: + + clockgen-a@90ff000 { + compatible = "st,clkgen-c32"; + reg = <0x90ff000 0x1000>; + + clk_s_a0_pll: clk-s-a0-pll { + #clock-cells = <1>; + compatible = "st,clkgen-pll0"; + + clocks = <&clk_sysin>; + + clock-output-names = "clk-s-a0-pll-ofd-0"; + }; + + clk_s_a0_flexgen: clk-s-a0-flexgen { + compatible = "st,flexgen"; + + #clock-cells = <1>; + + clocks = <&clk_s_a0_pll 0>, + <&clk_sysin>; + + clock-output-names = "clk-ic-lmi0"; + }; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,flexgen.txt b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt new file mode 100644 index 000000000..c91807540 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,flexgen.txt @@ -0,0 +1,133 @@ +Binding for a type of flexgen structure found on certain +STMicroelectronics consumer electronics SoC devices + +This structure includes: +- a clock cross bar (represented by a mux element) +- a pre and final dividers (represented by a divider and gate elements) + +Flexgen structure is a part of Clockgen[1]. + +Please find an example below: + + Clockgen block diagram + ------------------------------------------------------------------- + | Flexgen structure | + | --------------------------------------------- | + | | ------- -------- -------- | | +clk_sysin | | | | | | | | | +---|-----------------|-->| | | | | | | | + | | | | | | | | | | | + | | ------- | | | |Pre | |Final | | | + | | |PLL0 | | | | |Dividers| |Dividers| | | + | |->| | | | | | x32 | | x32 | | | + | | | odf_0|----|-->| | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | ------- | | | | | | | | | + | | | | | | | | | | | + | | ------- | | Clock | | | | | | | + | | |PLL1 | | | | | | | | | | + | |->| | | | Cross | | | | | | | + | | | odf_0|----|-->| | | | | | CLK_DIV[31:0] + | | | | | | Bar |====>| |====>| |===|=========> + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | | | | | | | | | | | | + | | ------- | | | | | | | | | + | | | | | | | | | | | + | | ------- | | | | | | | | | + | | |QUADFS | | | | | | | | | | + | |->| ch0|----|-->| | | | | | | | + | | | | | | | | | | | | + | | ch1|----|-->| | | | | | | | + | | | | | | | | | | | | + | | ch2|----|-->| | | DIV | | DIV | | | + | | | | | | | 1 to | | 1 to | | | + | | ch3|----|-->| | | 1024 | | 64 | | | + | ------- | | | | | | | | | + | | ------- -------- -------- | | + | -------------------------------------------- | + | | + ------------------------------------------------------------------- + +This binding uses the common clock binding[2]. + +[1] Documentation/devicetree/bindings/clock/st/st,clkgen.txt +[2] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be: + "st,flexgen" + "st,flexgen-audio", "st,flexgen" (enable clock propagation on parent for + audio use case) + "st,flexgen-video", "st,flexgen" (enable clock propagation on parent + and activate synchronous mode) + "st,flexgen-stih407-a0" + "st,flexgen-stih410-a0" + "st,flexgen-stih407-c0" + "st,flexgen-stih410-c0" + "st,flexgen-stih418-c0" + "st,flexgen-stih407-d0" + "st,flexgen-stih410-d0" + "st,flexgen-stih407-d2" + "st,flexgen-stih418-d2" + "st,flexgen-stih407-d3" + +- #clock-cells : from common clock binding; shall be set to 1 (multiple clock + outputs). + +- clocks : must be set to the parent's phandle. it could be output clocks of + a quadsfs or/and a pll or/and clk_sysin (up to 7 clocks) + +- clock-output-names : List of strings used to name the clock outputs. + +Example: + + clk_s_c0_flexgen: clk-s-c0-flexgen { + + #clock-cells = <1>; + compatible = "st,flexgen"; + + clocks = <&clk_s_c0_pll0 0>, + <&clk_s_c0_pll1 0>, + <&clk_s_c0_quadfs 0>, + <&clk_s_c0_quadfs 1>, + <&clk_s_c0_quadfs 2>, + <&clk_s_c0_quadfs 3>, + <&clk_sysin>; + + clock-output-names = "clk-icn-gpu", + "clk-fdma", + "clk-nand", + "clk-hva", + "clk-proc-stfe", + "clk-proc-tp", + "clk-rx-icn-dmu", + "clk-rx-icn-hva", + "clk-icn-cpu", + "clk-tx-icn-dmu", + "clk-mmc-0", + "clk-mmc-1", + "clk-jpegdec", + "clk-ext2fa9", + "clk-ic-bdisp-0", + "clk-ic-bdisp-1", + "clk-pp-dmu", + "clk-vid-dmu", + "clk-dss-lpc", + "clk-st231-aud-0", + "clk-st231-gp-1", + "clk-st231-dmu", + "clk-icn-lmi", + "clk-tx-icn-disp-1", + "clk-icn-sbc", + "clk-stfe-frc2", + "clk-eth-phy", + "clk-eth-ref-phyclk", + "clk-flash-promip", + "clk-main-disp", + "clk-aux-disp", + "clk-compo-dvp"; + }; diff --git a/Documentation/devicetree/bindings/clock/st/st,quadfs.txt b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt new file mode 100644 index 000000000..c4ba2adb0 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/st/st,quadfs.txt @@ -0,0 +1,48 @@ +Binding for a type of quad channel digital frequency synthesizer found on +certain STMicroelectronics consumer electronics SoC devices. + +This version contains a programmable PLL which can generate up to 216, 432 +or 660MHz (from a 30MHz oscillator input) as the input to the digital +synthesizers. + +This binding uses the common clock binding[1]. + +[1] Documentation/devicetree/bindings/clock/clock-bindings.txt + +Required properties: +- compatible : shall be: + "st,quadfs" + "st,quadfs-d0" + "st,quadfs-d2" + "st,quadfs-d3" + "st,quadfs-pll" + + +- #clock-cells : from common clock binding; shall be set to 1. + +- reg : A Base address and length of the register set. + +- clocks : from common clock binding + +- clock-output-names : From common clock binding. The block has 4 + clock outputs but not all of them in a specific instance + have to be used in the SoC. If a clock name is left as + an empty string then no clock will be created for the + output associated with that string index. If fewer than + 4 strings are provided then no clocks will be created + for the remaining outputs. + +Example: + + clk_s_c0_quadfs: clk-s-c0-quadfs@9103000 { + #clock-cells = <1>; + compatible = "st,quadfs-pll"; + reg = <0x9103000 0x1000>; + + clocks = <&clk_sysin>; + + clock-output-names = "clk-s-c0-fs0-ch0", + "clk-s-c0-fs0-ch1", + "clk-s-c0-fs0-ch2", + "clk-s-c0-fs0-ch3"; + }; |