diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display/exynos')
| -rw-r--r-- | Documentation/devicetree/bindings/display/exynos/exynos_dp.txt | 112 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt | 90 |
2 files changed, 202 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt new file mode 100644 index 000000000..9b6cba3f8 --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt @@ -0,0 +1,112 @@ +The Exynos display port interface should be configured based on +the type of panel connected to it. + +We use two nodes: + -dp-controller node + -dptx-phy node(defined inside dp-controller node) + +For the DP-PHY initialization, we use the dptx-phy node. +Required properties for dptx-phy: deprecated, use phys and phy-names + -reg: deprecated + Base address of DP PHY register. + -samsung,enable-mask: deprecated + The bit-mask used to enable/disable DP PHY. + +For the Panel initialization, we read data from dp-controller node. +Required properties for dp-controller: + -compatible: + should be "samsung,exynos5-dp". + -reg: + physical base address of the controller and length + of memory mapped region. + -interrupts: + interrupt combiner values. + -clocks: + from common clock binding: handle to dp clock. + -clock-names: + from common clock binding: Shall be "dp". + -phys: + from general PHY binding: the phandle for the PHY device. + -phy-names: + from general PHY binding: Should be "dp". + +Optional properties for dp-controller: + -interlaced: + interlace scan mode. + Progressive if defined, Interlaced if not defined + -vsync-active-high: + VSYNC polarity configuration. + High if defined, Low if not defined + -hsync-active-high: + HSYNC polarity configuration. + High if defined, Low if not defined + -samsung,hpd-gpio: + Hotplug detect GPIO. + Indicates which GPIO should be used for hotplug + detection + -video interfaces: Device node can contain video interface port + nodes according to [1]. + - display-timings: timings for the connected panel as described by + Documentation/devicetree/bindings/display/panel/display-timing.txt + +For the below properties, please refer to Analogix DP binding document: + * Documentation/devicetree/bindings/display/bridge/analogix_dp.txt + -phys (required) + -phy-names (required) + -hpd-gpios (optional) + force-hpd (optional) + +Deprecated properties for DisplayPort: +-interlaced: deprecated prop that can parsed from drm_display_mode. +-vsync-active-high: deprecated prop that can parsed from drm_display_mode. +-hsync-active-high: deprecated prop that can parsed from drm_display_mode. +-samsung,ycbcr-coeff: deprecated prop that can parsed from drm_display_mode. +-samsung,dynamic-range: deprecated prop that can parsed from drm_display_mode. +-samsung,color-space: deprecated prop that can parsed from drm_display_info. +-samsung,color-depth: deprecated prop that can parsed from drm_display_info. +-samsung,link-rate: deprecated prop that can reading from monitor by dpcd method. +-samsung,lane-count: deprecated prop that can reading from monitor by dpcd method. +-samsung,hpd-gpio: deprecated name for hpd-gpios. + +------------------------------------------------------------------------------- + +Example: + +SOC specific portion: + dp-controller { + compatible = "samsung,exynos5-dp"; + reg = <0x145b0000 0x10000>; + interrupts = <10 3>; + interrupt-parent = <&combiner>; + clocks = <&clock 342>; + clock-names = "dp"; + + phys = <&dp_phy>; + phy-names = "dp"; + }; + +Board Specific portion: + dp-controller { + display-timings { + native-mode = <&lcd_timing>; + lcd_timing: 1366x768 { + clock-frequency = <70589280>; + hactive = <1366>; + vactive = <768>; + hfront-porch = <40>; + hback-porch = <40>; + hsync-len = <32>; + vback-porch = <10>; + vfront-porch = <12>; + vsync-len = <6>; + }; + }; + + ports { + port@0 { + dp_out: endpoint { + remote-endpoint = <&bridge_in>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt new file mode 100644 index 000000000..be377786e --- /dev/null +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dsim.txt @@ -0,0 +1,90 @@ +Exynos MIPI DSI Master + +Required properties: + - compatible: value should be one of the following + "samsung,exynos3250-mipi-dsi" /* for Exynos3250/3472 SoCs */ + "samsung,exynos4210-mipi-dsi" /* for Exynos4 SoCs */ + "samsung,exynos5410-mipi-dsi" /* for Exynos5410/5420/5440 SoCs */ + "samsung,exynos5422-mipi-dsi" /* for Exynos5422/5800 SoCs */ + "samsung,exynos5433-mipi-dsi" /* for Exynos5433 SoCs */ + - reg: physical base address and length of the registers set for the device + - interrupts: should contain DSI interrupt + - clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names + - clock-names: should include "bus_clk"and "sclk_mipi" entries + the use of "pll_clk" is deprecated + - phys: list of phy specifiers, must contain an entry for each required + entry in phy-names + - phy-names: should include "dsim" entry + - vddcore-supply: MIPI DSIM Core voltage supply (e.g. 1.1V) + - vddio-supply: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V) + - samsung,pll-clock-frequency: specifies frequency of the oscillator clock + - #address-cells, #size-cells: should be set respectively to <1> and <0> + according to DSI host bindings (see MIPI DSI bindings [1]) + - samsung,burst-clock-frequency: specifies DSI frequency in high-speed burst + mode + - samsung,esc-clock-frequency: specifies DSI frequency in escape mode + +Optional properties: + - power-domains: a phandle to DSIM power domain node + +Child nodes: + Should contain DSI peripheral nodes (see MIPI DSI bindings [1]). + +Video interfaces: + Device node can contain following video interface port nodes according to [2]: + 0: RGB input, + 1: DSI output + +[1]: Documentation/devicetree/bindings/display/mipi-dsi-bus.txt +[2]: Documentation/devicetree/bindings/media/video-interfaces.txt + +Example: + + dsi@11c80000 { + compatible = "samsung,exynos4210-mipi-dsi"; + reg = <0x11C80000 0x10000>; + interrupts = <0 79 0>; + clocks = <&clock 286>, <&clock 143>; + clock-names = "bus_clk", "sclk_mipi"; + phys = <&mipi_phy 1>; + phy-names = "dsim"; + vddcore-supply = <&vusb_reg>; + vddio-supply = <&vmipi_reg>; + power-domains = <&pd_lcd0>; + #address-cells = <1>; + #size-cells = <0>; + samsung,pll-clock-frequency = <24000000>; + + panel@1 { + reg = <0>; + ... + port { + panel_ep: endpoint { + remote-endpoint = <&dsi_ep>; + }; + }; + }; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + decon_to_mic: endpoint { + remote-endpoint = <&mic_to_decon>; + }; + }; + + port@1 { + reg = <1>; + dsi_ep: endpoint { + reg = <0>; + samsung,burst-clock-frequency = <500000000>; + samsung,esc-clock-frequency = <20000000>; + remote-endpoint = <&panel_ep>; + }; + }; + }; + }; |