diff options
Diffstat (limited to 'Documentation/devicetree/bindings/display/imx')
5 files changed, 599 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt b/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt new file mode 100644 index 000000000..f4df9e83b --- /dev/null +++ b/Documentation/devicetree/bindings/display/imx/fsl,imx-fb.txt @@ -0,0 +1,57 @@ +Freescale imx21 Framebuffer + +This framebuffer driver supports devices imx1, imx21, imx25, and imx27. + +Required properties: +- compatible : "fsl,<chip>-fb", chip should be imx1 or imx21 +- reg : Should contain 1 register ranges(address and length) +- interrupts : One interrupt of the fb dev + +Required nodes: +- display: Phandle to a display node as described in + Documentation/devicetree/bindings/display/panel/display-timing.txt + Additional, the display node has to define properties: + - bits-per-pixel: Bits per pixel + - fsl,pcr: LCDC PCR value + A display node may optionally define + - fsl,aus-mode: boolean to enable AUS mode (only for imx21) + +Optional properties: +- lcd-supply: Regulator for LCD supply voltage. +- fsl,dmacr: DMA Control Register value. This is optional. By default, the + register is not modified as recommended by the datasheet. +- fsl,lpccr: Contrast Control Register value. This property provides the + default value for the contrast control register. + If that property is omitted, the register is zeroed. +- fsl,lscr1: LCDC Sharp Configuration Register value. + +Example: + + imxfb: fb@10021000 { + compatible = "fsl,imx21-fb"; + interrupts = <61>; + reg = <0x10021000 0x1000>; + display = <&display0>; + }; + + ... + + display0: display0 { + model = "Primeview-PD050VL1"; + bits-per-pixel = <16>; + fsl,pcr = <0xf0c88080>; /* non-standard but required */ + display-timings { + native-mode = <&timing_disp0>; + timing_disp0: 640x480 { + hactive = <640>; + vactive = <480>; + hback-porch = <112>; + hfront-porch = <36>; + hsync-len = <32>; + vback-porch = <33>; + vfront-porch = <33>; + vsync-len = <2>; + clock-frequency = <25000000>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml new file mode 100644 index 000000000..af7fe9c4d --- /dev/null +++ b/Documentation/devicetree/bindings/display/imx/fsl,imx6-hdmi.yaml @@ -0,0 +1,126 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/display/imx/fsl,imx6-hdmi.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX6 DWC HDMI TX Encoder + +maintainers: + - Philipp Zabel <p.zabel@pengutronix.de> + +description: | + The HDMI transmitter is a Synopsys DesignWare HDMI 1.4 TX controller IP + with a companion PHY IP. + +allOf: + - $ref: ../bridge/synopsys,dw-hdmi.yaml# + +properties: + compatible: + enum: + - fsl,imx6dl-hdmi + - fsl,imx6q-hdmi + + reg-io-width: + const: 1 + + clocks: + maxItems: 2 + + clock-names: + maxItems: 2 + + ddc-i2c-bus: + $ref: /schemas/types.yaml#/definitions/phandle + description: + The HDMI DDC bus can be connected to either a system I2C master or the + functionally-reduced I2C master contained in the DWC HDMI. When connected + to a system I2C master this property contains a phandle to that I2C + master controller. + + gpr: + $ref: /schemas/types.yaml#/definitions/phandle + description: + phandle to the iomuxc-gpr region containing the HDMI multiplexer control + register. + + ports: + $ref: /schemas/graph.yaml#/properties/ports + description: | + This device has four video ports, corresponding to the four inputs of the + HDMI multiplexer. Each port shall have a single endpoint. + + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: First input of the HDMI multiplexer + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Second input of the HDMI multiplexer + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: Third input of the HDMI multiplexer + + port@3: + $ref: /schemas/graph.yaml#/properties/port + description: Fourth input of the HDMI multiplexer + + anyOf: + - required: + - port@0 + - required: + - port@1 + - required: + - port@2 + - required: + - port@3 + +required: + - compatible + - reg + - clocks + - clock-names + - gpr + - interrupts + - ports + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx6qdl-clock.h> + + hdmi: hdmi@120000 { + reg = <0x00120000 0x9000>; + interrupts = <0 115 0x04>; + gpr = <&gpr>; + clocks = <&clks IMX6QDL_CLK_HDMI_IAHB>, + <&clks IMX6QDL_CLK_HDMI_ISFR>; + clock-names = "iahb", "isfr"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + hdmi_mux_0: endpoint { + remote-endpoint = <&ipu1_di0_hdmi>; + }; + }; + + port@1 { + reg = <1>; + + hdmi_mux_1: endpoint { + remote-endpoint = <&ipu1_di1_hdmi>; + }; + }; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt new file mode 100644 index 000000000..3c35338a2 --- /dev/null +++ b/Documentation/devicetree/bindings/display/imx/fsl-imx-drm.txt @@ -0,0 +1,162 @@ +Freescale i.MX DRM master device +================================ + +The freescale i.MX DRM master device is a virtual device needed to list all +IPU or other display interface nodes that comprise the graphics subsystem. + +Required properties: +- compatible: Should be "fsl,imx-display-subsystem" +- ports: Should contain a list of phandles pointing to display interface ports + of IPU devices + +example: + +display-subsystem { + compatible = "fsl,imx-display-subsystem"; + ports = <&ipu_di0>; +}; + + +Freescale i.MX IPUv3 +==================== + +Required properties: +- compatible: Should be "fsl,<chip>-ipu" where <chip> is one of + - imx51 + - imx53 + - imx6q + - imx6qp +- reg: should be register base and length as documented in the + datasheet +- interrupts: Should contain sync interrupt and error interrupt, + in this order. +- resets: phandle pointing to the system reset controller and + reset line index, see reset/fsl,imx-src.txt for details +Additional required properties for fsl,imx6qp-ipu: +- fsl,prg: phandle to prg node associated with this IPU instance +Optional properties: +- port@[0-3]: Port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Ports 0 and 1 should correspond to CSI0 and CSI1, + ports 2 and 3 should correspond to DI0 and DI1, respectively. + +example: + +ipu: ipu@18000000 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx53-ipu"; + reg = <0x18000000 0x080000000>; + interrupts = <11 10>; + resets = <&src 2>; + + ipu_di0: port@2 { + reg = <2>; + + ipu_di0_disp0: endpoint { + remote-endpoint = <&display_in>; + }; + }; +}; + +Freescale i.MX PRE (Prefetch Resolve Engine) +============================================ + +Required properties: +- compatible: should be "fsl,imx6qp-pre" +- reg: should be register base and length as documented in the + datasheet +- clocks : phandle to the PRE axi clock input, as described + in Documentation/devicetree/bindings/clock/clock-bindings.txt and + Documentation/devicetree/bindings/clock/imx6q-clock.yaml. +- clock-names: should be "axi" +- interrupts: should contain the PRE interrupt +- fsl,iram: phandle pointing to the mmio-sram device node, that should be + used for the PRE SRAM double buffer. + +example: + +pre@21c8000 { + compatible = "fsl,imx6qp-pre"; + reg = <0x021c8000 0x1000>; + interrupts = <GIC_SPI 90 IRQ_TYPE_EDGE_RISING>; + clocks = <&clks IMX6QDL_CLK_PRE0>; + clock-names = "axi"; + fsl,iram = <&ocram2>; +}; + +Freescale i.MX PRG (Prefetch Resolve Gasket) +============================================ + +Required properties: +- compatible: should be "fsl,imx6qp-prg" +- reg: should be register base and length as documented in the + datasheet +- clocks : phandles to the PRG ipg and axi clock inputs, as described + in Documentation/devicetree/bindings/clock/clock-bindings.txt and + Documentation/devicetree/bindings/clock/imx6q-clock.yaml. +- clock-names: should be "ipg" and "axi" +- fsl,pres: phandles to the PRE units attached to this PRG, with the fixed + PRE as the first entry and the muxable PREs following. + +example: + +prg@21cc000 { + compatible = "fsl,imx6qp-prg"; + reg = <0x021cc000 0x1000>; + clocks = <&clks IMX6QDL_CLK_PRG0_APB>, + <&clks IMX6QDL_CLK_PRG0_AXI>; + clock-names = "ipg", "axi"; + fsl,pres = <&pre1>, <&pre2>, <&pre3>; +}; + +Parallel display support +======================== + +Required properties: +- compatible: Should be "fsl,imx-parallel-display" +Optional properties: +- interface-pix-fmt: How this display is connected to the + display interface. Currently supported types: "rgb24", "rgb565", "bgr666" + and "lvds666". +- edid: verbatim EDID data block describing attached display. +- ddc: phandle describing the i2c bus handling the display data + channel +- port@[0-1]: Port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/media/video-interfaces.txt. + Port 0 is the input port connected to the IPU display interface, + port 1 is the output port connected to a panel. + +example: + +disp0 { + compatible = "fsl,imx-parallel-display"; + edid = [edid-data]; + interface-pix-fmt = "rgb24"; + + port@0 { + reg = <0>; + + display_in: endpoint { + remote-endpoint = <&ipu_di0_disp0>; + }; + }; + + port@1 { + reg = <1>; + + display_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; +}; + +panel { + ... + + port { + panel_in: endpoint { + remote-endpoint = <&display_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/imx/ldb.txt b/Documentation/devicetree/bindings/display/imx/ldb.txt new file mode 100644 index 000000000..8e6e7d797 --- /dev/null +++ b/Documentation/devicetree/bindings/display/imx/ldb.txt @@ -0,0 +1,147 @@ +Device-Tree bindings for LVDS Display Bridge (ldb) + +LVDS Display Bridge +=================== + +The LVDS Display Bridge device tree node contains up to two lvds-channel +nodes describing each of the two LVDS encoder channels of the bridge. + +Required properties: + - #address-cells : should be <1> + - #size-cells : should be <0> + - compatible : should be "fsl,imx53-ldb" or "fsl,imx6q-ldb". + Both LDB versions are similar, but i.MX6 has an additional + multiplexer in the front to select any of the four IPU display + interfaces as input for each LVDS channel. + - gpr : should be <&gpr> on i.MX53 and i.MX6q. + The phandle points to the iomuxc-gpr region containing the LVDS + control register. +- clocks, clock-names : phandles to the LDB divider and selector clocks and to + the display interface selector clocks, as described in + Documentation/devicetree/bindings/clock/clock-bindings.txt + The following clocks are expected on i.MX53: + "di0_pll" - LDB LVDS channel 0 mux + "di1_pll" - LDB LVDS channel 1 mux + "di0" - LDB LVDS channel 0 gate + "di1" - LDB LVDS channel 1 gate + "di0_sel" - IPU1 DI0 mux + "di1_sel" - IPU1 DI1 mux + On i.MX6q the following additional clocks are needed: + "di2_sel" - IPU2 DI0 mux + "di3_sel" - IPU2 DI1 mux + The needed clock numbers for each are documented in + Documentation/devicetree/bindings/clock/imx5-clock.yaml, and in + Documentation/devicetree/bindings/clock/imx6q-clock.yaml. + +Optional properties: + - pinctrl-names : should be "default" on i.MX53, not used on i.MX6q + - pinctrl-0 : a phandle pointing to LVDS pin settings on i.MX53, + not used on i.MX6q + - fsl,dual-channel : boolean. if it exists, only LVDS channel 0 should + be configured - one input will be distributed on both outputs in dual + channel mode + +LVDS Channel +============ + +Each LVDS Channel has to contain either an of graph link to a panel device node +or a display-timings node that describes the video timings for the connected +LVDS display as well as the fsl,data-mapping and fsl,data-width properties. + +Required properties: + - reg : should be <0> or <1> + - port: Input and output port nodes with endpoint definitions as defined in + Documentation/devicetree/bindings/graph.txt. + On i.MX5, the internal two-input-multiplexer is used. Due to hardware + limitations, only one input port (port@[0,1]) can be used for each channel + (lvds-channel@[0,1], respectively). + On i.MX6, there should be four input ports (port@[0-3]) that correspond + to the four LVDS multiplexer inputs. + A single output port (port@2 on i.MX5, port@4 on i.MX6) must be connected + to a panel input port. Optionally, the output port can be left out if + display-timings are used instead. + +Optional properties (required if display-timings are used): + - ddc-i2c-bus: phandle of an I2C controller used for DDC EDID probing + - display-timings : A node that describes the display timings as defined in + Documentation/devicetree/bindings/display/panel/display-timing.txt. + - fsl,data-mapping : should be "spwg" or "jeida" + This describes how the color bits are laid out in the + serialized LVDS signal. + - fsl,data-width : should be <18> or <24> + +example: + +gpr: iomuxc-gpr@53fa8000 { + /* ... */ +}; + +ldb: ldb@53fa8008 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,imx53-ldb"; + gpr = <&gpr>; + clocks = <&clks IMX5_CLK_LDB_DI0_SEL>, + <&clks IMX5_CLK_LDB_DI1_SEL>, + <&clks IMX5_CLK_IPU_DI0_SEL>, + <&clks IMX5_CLK_IPU_DI1_SEL>, + <&clks IMX5_CLK_LDB_DI0_GATE>, + <&clks IMX5_CLK_LDB_DI1_GATE>; + clock-names = "di0_pll", "di1_pll", + "di0_sel", "di1_sel", + "di0", "di1"; + + /* Using an of-graph endpoint link to connect the panel */ + lvds-channel@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + port@0 { + reg = <0>; + + lvds0_in: endpoint { + remote-endpoint = <&ipu_di0_lvds0>; + }; + }; + + port@2 { + reg = <2>; + + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; + + /* Using display-timings and fsl,data-mapping/width instead */ + lvds-channel@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + fsl,data-mapping = "spwg"; + fsl,data-width = <24>; + + display-timings { + /* ... */ + }; + + port@1 { + reg = <1>; + + lvds1_in: endpoint { + remote-endpoint = <&ipu_di1_lvds1>; + }; + }; + }; +}; + +panel: lvds-panel { + /* ... */ + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/display/imx/nxp,imx8mq-dcss.yaml b/Documentation/devicetree/bindings/display/imx/nxp,imx8mq-dcss.yaml new file mode 100644 index 000000000..989ab312c --- /dev/null +++ b/Documentation/devicetree/bindings/display/imx/nxp,imx8mq-dcss.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 NXP +%YAML 1.2 +--- +$id: "http://devicetree.org/schemas/display/imx/nxp,imx8mq-dcss.yaml#" +$schema: "http://devicetree.org/meta-schemas/core.yaml#" + +title: iMX8MQ Display Controller Subsystem (DCSS) + +maintainers: + - Laurentiu Palcu <laurentiu.palcu@nxp.com> + +description: + + The DCSS (display controller sub system) is used to source up to three + display buffers, compose them, and drive a display using HDMI 2.0a(with HDCP + 2.2) or MIPI-DSI. The DCSS is intended to support up to 4kp60 displays. HDR10 + image processing capabilities are included to provide a solution capable of + driving next generation high dynamic range displays. + +properties: + compatible: + const: nxp,imx8mq-dcss + + reg: + items: + - description: DCSS base address and size, up to IRQ steer start + - description: DCSS BLKCTL base address and size + + interrupts: + items: + - description: Context loader completion and error interrupt + - description: DTG interrupt used to signal context loader trigger time + - description: DTG interrupt for Vblank + + interrupt-names: + items: + - const: ctxld + - const: ctxld_kick + - const: vblank + + clocks: + items: + - description: Display APB clock for all peripheral PIO access interfaces + - description: Display AXI clock needed by DPR, Scaler, RTRAM_CTRL + - description: RTRAM clock + - description: Pixel clock, can be driven either by HDMI phy clock or MIPI + - description: DTRC clock, needed by video decompressor + + clock-names: + items: + - const: apb + - const: axi + - const: rtrm + - const: pix + - const: dtrc + + assigned-clocks: + items: + - description: Phandle and clock specifier of IMX8MQ_CLK_DISP_AXI_ROOT + - description: Phandle and clock specifier of IMX8MQ_CLK_DISP_RTRM + - description: Phandle and clock specifier of either IMX8MQ_VIDEO2_PLL1_REF_SEL or + IMX8MQ_VIDEO_PLL1_REF_SEL + + assigned-clock-parents: + items: + - description: Phandle and clock specifier of IMX8MQ_SYS1_PLL_800M + - description: Phandle and clock specifier of IMX8MQ_SYS1_PLL_800M + - description: Phandle and clock specifier of IMX8MQ_CLK_27M + + assigned-clock-rates: + items: + - description: Must be 800 MHz + - description: Must be 400 MHz + + port: + $ref: /schemas/graph.yaml#/properties/port + description: + A port node pointing to the input port of a HDMI/DP or MIPI display bridge. + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mq-clock.h> + dcss: display-controller@32e00000 { + compatible = "nxp,imx8mq-dcss"; + reg = <0x32e00000 0x2d000>, <0x32e2f000 0x1000>; + interrupts = <6>, <8>, <9>; + interrupt-names = "ctxld", "ctxld_kick", "vblank"; + interrupt-parent = <&irqsteer>; + clocks = <&clk IMX8MQ_CLK_DISP_APB_ROOT>, <&clk IMX8MQ_CLK_DISP_AXI_ROOT>, + <&clk IMX8MQ_CLK_DISP_RTRM_ROOT>, <&clk IMX8MQ_VIDEO2_PLL_OUT>, + <&clk IMX8MQ_CLK_DISP_DTRC>; + clock-names = "apb", "axi", "rtrm", "pix", "dtrc"; + assigned-clocks = <&clk IMX8MQ_CLK_DISP_AXI>, <&clk IMX8MQ_CLK_DISP_RTRM>, + <&clk IMX8MQ_VIDEO2_PLL1_REF_SEL>; + assigned-clock-parents = <&clk IMX8MQ_SYS1_PLL_800M>, <&clk IMX8MQ_SYS1_PLL_800M>, + <&clk IMX8MQ_CLK_27M>; + assigned-clock-rates = <800000000>, + <400000000>; + port { + dcss_out: endpoint { + remote-endpoint = <&hdmi_in>; + }; + }; + }; |