summaryrefslogtreecommitdiffstats
path: root/Documentation/devicetree/bindings/input/ti,drv260x.txt
diff options
context:
space:
mode:
Diffstat (limited to 'Documentation/devicetree/bindings/input/ti,drv260x.txt')
-rw-r--r--Documentation/devicetree/bindings/input/ti,drv260x.txt50
1 files changed, 50 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/input/ti,drv260x.txt b/Documentation/devicetree/bindings/input/ti,drv260x.txt
new file mode 100644
index 000000000..4c5312eaa
--- /dev/null
+++ b/Documentation/devicetree/bindings/input/ti,drv260x.txt
@@ -0,0 +1,50 @@
+* Texas Instruments - drv260x Haptics driver family
+
+Required properties:
+ - compatible - One of:
+ "ti,drv2604" - DRV2604
+ "ti,drv2605" - DRV2605
+ "ti,drv2605l" - DRV2605L
+ - reg - I2C slave address
+ - vbat-supply - Required supply regulator
+ - mode - Power up mode of the chip (defined in include/dt-bindings/input/ti-drv260x.h)
+ DRV260X_LRA_MODE - Linear Resonance Actuator mode (Piezoelectric)
+ DRV260X_LRA_NO_CAL_MODE - This is a LRA Mode but there is no calibration
+ sequence during init. And the device is configured for real
+ time playback mode (RTP mode).
+ DRV260X_ERM_MODE - Eccentric Rotating Mass mode (Rotary vibrator)
+ - library-sel - These are ROM based waveforms pre-programmed into the IC.
+ This should be set to set the library to use at power up.
+ (defined in include/dt-bindings/input/ti-drv260x.h)
+ DRV260X_LIB_EMPTY - Do not use a pre-programmed library
+ DRV260X_ERM_LIB_A - Pre-programmed Library
+ DRV260X_ERM_LIB_B - Pre-programmed Library
+ DRV260X_ERM_LIB_C - Pre-programmed Library
+ DRV260X_ERM_LIB_D - Pre-programmed Library
+ DRV260X_ERM_LIB_E - Pre-programmed Library
+ DRV260X_ERM_LIB_F - Pre-programmed Library
+ DRV260X_LIB_LRA - Pre-programmed LRA Library
+
+Optional properties:
+ - enable-gpio - gpio pin to enable/disable the device.
+ - vib-rated-mv - The rated voltage of the actuator in millivolts.
+ If this is not set then the value will be defaulted to
+ 3.2 v.
+ - vib-overdrive-mv - The overdrive voltage of the actuator in millivolts.
+ If this is not set then the value will be defaulted to
+ 3.2 v.
+Example:
+
+haptics: haptics@5a {
+ compatible = "ti,drv2605l";
+ reg = <0x5a>;
+ vbat-supply = <&vbat>;
+ enable-gpio = <&gpio1 28 GPIO_ACTIVE_HIGH>;
+ mode = <DRV260X_LRA_MODE>;
+ library-sel = <DRV260X_LIB_LRA>;
+ vib-rated-mv = <3200>;
+ vib-overdrive-mv = <3200>;
+}
+
+For more product information please see the link below:
+http://www.ti.com/product/drv2605