1 files changed, 109 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/net/dsa/marvell.txt b/Documentation/devicetree/bindings/net/dsa/marvell.txt
new file mode 100644
index 000000000..2363b4124
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/marvell.txt
@@ -0,0 +1,109 @@
+Marvell DSA Switch Device Tree Bindings
+---------------------------------------
+
+WARNING: This binding is currently unstable. Do not program it into a
+FLASH never to be changed again. Once this binding is stable, this
+warning will be removed.
+
+If you need a stable binding, use the old dsa.txt binding.
+
+Marvell Switches are MDIO devices. The following properties should be
+placed as a child node of an mdio device.
+
+The properties described here are those specific to Marvell devices.
+Additional required and optional properties can be found in dsa.txt.
+
+The compatibility string is used only to find an identification register,
+which is at a different MDIO base address in different switch families.
+- "marvell,mv88e6085"	: Switch has base address 0x10. Use with models:
+			  6085, 6095, 6097, 6123, 6131, 6141, 6161, 6165,
+			  6171, 6172, 6175, 6176, 6185, 6240, 6320, 6321,
+			  6341, 6350, 6351, 6352
+- "marvell,mv88e6190"	: Switch has base address 0x00. Use with models:
+			  6190, 6190X, 6191, 6290, 6390, 6390X
+- "marvell,mv88e6250"	: Switch has base address 0x08 or 0x18. Use with model:
+			  6220, 6250
+
+Required properties:
+- compatible		: Should be one of "marvell,mv88e6085",
+			  "marvell,mv88e6190" or "marvell,mv88e6250" as
+			  indicated above
+- reg			: Address on the MII bus for the switch.
+
+Optional properties:
+
+- reset-gpios		: Should be a gpio specifier for a reset line
+- interrupts		: Interrupt from the switch
+- interrupt-controller	: Indicates the switch is itself an interrupt
+			  controller. This is used for the PHY interrupts.
+#interrupt-cells = <2>	: Controller uses two cells, number and flag
+- eeprom-length		: Set to the length of an EEPROM connected to the
+			  switch. Must be set if the switch can not detect
+			  the presence and/or size of a connected EEPROM,
+			  otherwise optional.
+- mdio			: Container of PHY and devices on the switches MDIO
+			  bus.
+- mdio?		: Container of PHYs and devices on the external MDIO
+			  bus. The node must contains a compatible string of
+			  "marvell,mv88e6xxx-mdio-external"
+
+Example:
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		switch0: switch@0 {
+			compatible = "marvell,mv88e6085";
+			reg = <0>;
+			reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				switch1phy0: switch1phy0@0 {
+					reg = <0>;
+					interrupt-parent = <&switch0>;
+					interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+				};
+			};
+		};
+	};
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <27 IRQ_TYPE_LEVEL_LOW>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+
+		switch0: switch@0 {
+			compatible = "marvell,mv88e6190";
+			reg = <0>;
+			reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>;
+
+			mdio {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				switch1phy0: switch1phy0@0 {
+					reg = <0>;
+					interrupt-parent = <&switch0>;
+					interrupts = <0 IRQ_TYPE_LEVEL_HIGH>;
+				};
+			};
+
+			mdio1 {
+				compatible = "marvell,mv88e6xxx-mdio-external";
+				#address-cells = <1>;
+				#size-cells = <0>;
+				switch1phy9: switch1phy0@9 {
+					reg = <9>;
+				};
+			};
+		};
+	};