diff options
Diffstat (limited to 'Documentation/input')
37 files changed, 9191 insertions, 0 deletions
diff --git a/Documentation/input/devices/alps.rst b/Documentation/input/devices/alps.rst new file mode 100644 index 000000000..b556d6bde --- /dev/null +++ b/Documentation/input/devices/alps.rst @@ -0,0 +1,390 @@ +---------------------- +ALPS Touchpad Protocol +---------------------- + +Introduction +------------ +Currently the ALPS touchpad driver supports seven protocol versions in use by +ALPS touchpads, called versions 1, 2, 3, 4, 5, 6, 7 and 8. + +Since roughly mid-2010 several new ALPS touchpads have been released and +integrated into a variety of laptops and netbooks. These new touchpads +have enough behavior differences that the alps_model_data definition +table, describing the properties of the different versions, is no longer +adequate. The design choices were to re-define the alps_model_data +table, with the risk of regression testing existing devices, or isolate +the new devices outside of the alps_model_data table. The latter design +choice was made. The new touchpad signatures are named: "Rushmore", +"Pinnacle", and "Dolphin", which you will see in the alps.c code. +For the purposes of this document, this group of ALPS touchpads will +generically be called "new ALPS touchpads". + +We experimented with probing the ACPI interface _HID (Hardware ID)/_CID +(Compatibility ID) definition as a way to uniquely identify the +different ALPS variants but there did not appear to be a 1:1 mapping. +In fact, it appeared to be an m:n mapping between the _HID and actual +hardware type. + +Detection +--------- + +All ALPS touchpads should respond to the "E6 report" command sequence: +E8-E6-E6-E6-E9. An ALPS touchpad should respond with either 00-00-0A or +00-00-64 if no buttons are pressed. The bits 0-2 of the first byte will be 1s +if some buttons are pressed. + +If the E6 report is successful, the touchpad model is identified using the "E7 +report" sequence: E8-E7-E7-E7-E9. The response is the model signature and is +matched against known models in the alps_model_data_array. + +For older touchpads supporting protocol versions 3 and 4, the E7 report +model signature is always 73-02-64. To differentiate between these +versions, the response from the "Enter Command Mode" sequence must be +inspected as described below. + +The new ALPS touchpads have an E7 signature of 73-03-50 or 73-03-0A but +seem to be better differentiated by the EC Command Mode response. + +Command Mode +------------ + +Protocol versions 3 and 4 have a command mode that is used to read and write +one-byte device registers in a 16-bit address space. The command sequence +EC-EC-EC-E9 places the device in command mode, and the device will respond +with 88-07 followed by a third byte. This third byte can be used to determine +whether the devices uses the version 3 or 4 protocol. + +To exit command mode, PSMOUSE_CMD_SETSTREAM (EA) is sent to the touchpad. + +While in command mode, register addresses can be set by first sending a +specific command, either EC for v3 devices or F5 for v4 devices. Then the +address is sent one nibble at a time, where each nibble is encoded as a +command with optional data. This encoding differs slightly between the v3 and +v4 protocols. + +Once an address has been set, the addressed register can be read by sending +PSMOUSE_CMD_GETINFO (E9). The first two bytes of the response contains the +address of the register being read, and the third contains the value of the +register. Registers are written by writing the value one nibble at a time +using the same encoding used for addresses. + +For the new ALPS touchpads, the EC command is used to enter command +mode. The response in the new ALPS touchpads is significantly different, +and more important in determining the behavior. This code has been +separated from the original alps_model_data table and put in the +alps_identify function. For example, there seem to be two hardware init +sequences for the "Dolphin" touchpads as determined by the second byte +of the EC response. + +Packet Format +------------- + +In the following tables, the following notation is used:: + + CAPITALS = stick, miniscules = touchpad + +?'s can have different meanings on different models, such as wheel rotation, +extra buttons, stick buttons on a dualpoint, etc. + +PS/2 packet format +------------------ + +:: + + byte 0: 0 0 YSGN XSGN 1 M R L + byte 1: X7 X6 X5 X4 X3 X2 X1 X0 + byte 2: Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0 + +Note that the device never signals overflow condition. + +For protocol version 2 devices when the trackpoint is used, and no fingers +are on the touchpad, the M R L bits signal the combined status of both the +pointingstick and touchpad buttons. + +ALPS Absolute Mode - Protocol Version 1 +--------------------------------------- + +:: + + byte 0: 1 0 0 0 1 x9 x8 x7 + byte 1: 0 x6 x5 x4 x3 x2 x1 x0 + byte 2: 0 ? ? l r ? fin ges + byte 3: 0 ? ? ? ? y9 y8 y7 + byte 4: 0 y6 y5 y4 y3 y2 y1 y0 + byte 5: 0 z6 z5 z4 z3 z2 z1 z0 + +ALPS Absolute Mode - Protocol Version 2 +--------------------------------------- + +:: + + byte 0: 1 ? ? ? 1 PSM PSR PSL + byte 1: 0 x6 x5 x4 x3 x2 x1 x0 + byte 2: 0 x10 x9 x8 x7 ? fin ges + byte 3: 0 y9 y8 y7 1 M R L + byte 4: 0 y6 y5 y4 y3 y2 y1 y0 + byte 5: 0 z6 z5 z4 z3 z2 z1 z0 + +Protocol Version 2 DualPoint devices send standard PS/2 mouse packets for +the DualPoint Stick. The M, R and L bits signal the combined status of both +the pointingstick and touchpad buttons, except for Dell dualpoint devices +where the pointingstick buttons get reported separately in the PSM, PSR +and PSL bits. + +Dualpoint device -- interleaved packet format +--------------------------------------------- + +:: + + byte 0: 1 1 0 0 1 1 1 1 + byte 1: 0 x6 x5 x4 x3 x2 x1 x0 + byte 2: 0 x10 x9 x8 x7 0 fin ges + byte 3: 0 0 YSGN XSGN 1 1 1 1 + byte 4: X7 X6 X5 X4 X3 X2 X1 X0 + byte 5: Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0 + byte 6: 0 y9 y8 y7 1 m r l + byte 7: 0 y6 y5 y4 y3 y2 y1 y0 + byte 8: 0 z6 z5 z4 z3 z2 z1 z0 + +Devices which use the interleaving format normally send standard PS/2 mouse +packets for the DualPoint Stick + ALPS Absolute Mode packets for the +touchpad, switching to the interleaved packet format when both the stick and +the touchpad are used at the same time. + +ALPS Absolute Mode - Protocol Version 3 +--------------------------------------- + +ALPS protocol version 3 has three different packet formats. The first two are +associated with touchpad events, and the third is associated with trackstick +events. + +The first type is the touchpad position packet:: + + byte 0: 1 ? x1 x0 1 1 1 1 + byte 1: 0 x10 x9 x8 x7 x6 x5 x4 + byte 2: 0 y10 y9 y8 y7 y6 y5 y4 + byte 3: 0 M R L 1 m r l + byte 4: 0 mt x3 x2 y3 y2 y1 y0 + byte 5: 0 z6 z5 z4 z3 z2 z1 z0 + +Note that for some devices the trackstick buttons are reported in this packet, +and on others it is reported in the trackstick packets. + +The second packet type contains bitmaps representing the x and y axes. In the +bitmaps a given bit is set if there is a finger covering that position on the +given axis. Thus the bitmap packet can be used for low-resolution multi-touch +data, although finger tracking is not possible. This packet also encodes the +number of contacts (f1 and f0 in the table below):: + + byte 0: 1 1 x1 x0 1 1 1 1 + byte 1: 0 x8 x7 x6 x5 x4 x3 x2 + byte 2: 0 y7 y6 y5 y4 y3 y2 y1 + byte 3: 0 y10 y9 y8 1 1 1 1 + byte 4: 0 x14 x13 x12 x11 x10 x9 y0 + byte 5: 0 1 ? ? ? ? f1 f0 + +This packet only appears after a position packet with the mt bit set, and +usually only appears when there are two or more contacts (although +occasionally it's seen with only a single contact). + +The final v3 packet type is the trackstick packet:: + + byte 0: 1 1 x7 y7 1 1 1 1 + byte 1: 0 x6 x5 x4 x3 x2 x1 x0 + byte 2: 0 y6 y5 y4 y3 y2 y1 y0 + byte 3: 0 1 TP SW 1 M R L + byte 4: 0 z6 z5 z4 z3 z2 z1 z0 + byte 5: 0 0 1 1 1 1 1 1 + +TP means Tap SW status when tap processing is enabled or Press status when press +processing is enabled. SW means scroll up when 4 buttons are available. + +ALPS Absolute Mode - Protocol Version 4 +--------------------------------------- + +Protocol version 4 has an 8-byte packet format:: + + byte 0: 1 ? x1 x0 1 1 1 1 + byte 1: 0 x10 x9 x8 x7 x6 x5 x4 + byte 2: 0 y10 y9 y8 y7 y6 y5 y4 + byte 3: 0 1 x3 x2 y3 y2 y1 y0 + byte 4: 0 ? ? ? 1 ? r l + byte 5: 0 z6 z5 z4 z3 z2 z1 z0 + byte 6: bitmap data (described below) + byte 7: bitmap data (described below) + +The last two bytes represent a partial bitmap packet, with 3 full packets +required to construct a complete bitmap packet. Once assembled, the 6-byte +bitmap packet has the following format:: + + byte 0: 0 1 x7 x6 x5 x4 x3 x2 + byte 1: 0 x1 x0 y4 y3 y2 y1 y0 + byte 2: 0 0 ? x14 x13 x12 x11 x10 + byte 3: 0 x9 x8 y9 y8 y7 y6 y5 + byte 4: 0 0 0 0 0 0 0 0 + byte 5: 0 0 0 0 0 0 0 y10 + +There are several things worth noting here. + + 1) In the bitmap data, bit 6 of byte 0 serves as a sync byte to + identify the first fragment of a bitmap packet. + + 2) The bitmaps represent the same data as in the v3 bitmap packets, although + the packet layout is different. + + 3) There doesn't seem to be a count of the contact points anywhere in the v4 + protocol packets. Deriving a count of contact points must be done by + analyzing the bitmaps. + + 4) There is a 3 to 1 ratio of position packets to bitmap packets. Therefore + MT position can only be updated for every third ST position update, and + the count of contact points can only be updated every third packet as + well. + +So far no v4 devices with tracksticks have been encountered. + +ALPS Absolute Mode - Protocol Version 5 +--------------------------------------- +This is basically Protocol Version 3 but with different logic for packet +decode. It uses the same alps_process_touchpad_packet_v3 call with a +specialized decode_fields function pointer to correctly interpret the +packets. This appears to only be used by the Dolphin devices. + +For single-touch, the 6-byte packet format is:: + + byte 0: 1 1 0 0 1 0 0 0 + byte 1: 0 x6 x5 x4 x3 x2 x1 x0 + byte 2: 0 y6 y5 y4 y3 y2 y1 y0 + byte 3: 0 M R L 1 m r l + byte 4: y10 y9 y8 y7 x10 x9 x8 x7 + byte 5: 0 z6 z5 z4 z3 z2 z1 z0 + +For mt, the format is:: + + byte 0: 1 1 1 n3 1 n2 n1 x24 + byte 1: 1 y7 y6 y5 y4 y3 y2 y1 + byte 2: ? x2 x1 y12 y11 y10 y9 y8 + byte 3: 0 x23 x22 x21 x20 x19 x18 x17 + byte 4: 0 x9 x8 x7 x6 x5 x4 x3 + byte 5: 0 x16 x15 x14 x13 x12 x11 x10 + +ALPS Absolute Mode - Protocol Version 6 +--------------------------------------- + +For trackstick packet, the format is:: + + byte 0: 1 1 1 1 1 1 1 1 + byte 1: 0 X6 X5 X4 X3 X2 X1 X0 + byte 2: 0 Y6 Y5 Y4 Y3 Y2 Y1 Y0 + byte 3: ? Y7 X7 ? ? M R L + byte 4: Z7 Z6 Z5 Z4 Z3 Z2 Z1 Z0 + byte 5: 0 1 1 1 1 1 1 1 + +For touchpad packet, the format is:: + + byte 0: 1 1 1 1 1 1 1 1 + byte 1: 0 0 0 0 x3 x2 x1 x0 + byte 2: 0 0 0 0 y3 y2 y1 y0 + byte 3: ? x7 x6 x5 x4 ? r l + byte 4: ? y7 y6 y5 y4 ? ? ? + byte 5: z7 z6 z5 z4 z3 z2 z1 z0 + +(v6 touchpad does not have middle button) + +ALPS Absolute Mode - Protocol Version 7 +--------------------------------------- + +For trackstick packet, the format is:: + + byte 0: 0 1 0 0 1 0 0 0 + byte 1: 1 1 * * 1 M R L + byte 2: X7 1 X5 X4 X3 X2 X1 X0 + byte 3: Z6 1 Y6 X6 1 Y2 Y1 Y0 + byte 4: Y7 0 Y5 Y4 Y3 1 1 0 + byte 5: T&P 0 Z5 Z4 Z3 Z2 Z1 Z0 + +For touchpad packet, the format is:: + + packet-fmt b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: TWO & MULTI L 1 R M 1 Y0-2 Y0-1 Y0-0 + byte 0: NEW L 1 X1-5 1 1 Y0-2 Y0-1 Y0-0 + byte 1: Y0-10 Y0-9 Y0-8 Y0-7 Y0-6 Y0-5 Y0-4 Y0-3 + byte 2: X0-11 1 X0-10 X0-9 X0-8 X0-7 X0-6 X0-5 + byte 3: X1-11 1 X0-4 X0-3 1 X0-2 X0-1 X0-0 + byte 4: TWO X1-10 TWO X1-9 X1-8 X1-7 X1-6 X1-5 X1-4 + byte 4: MULTI X1-10 TWO X1-9 X1-8 X1-7 X1-6 Y1-5 1 + byte 4: NEW X1-10 TWO X1-9 X1-8 X1-7 X1-6 0 0 + byte 5: TWO & NEW Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 Y1-5 Y1-4 + byte 5: MULTI Y1-10 0 Y1-9 Y1-8 Y1-7 Y1-6 F-1 F-0 + + L: Left button + R / M: Non-clickpads: Right / Middle button + Clickpads: When > 2 fingers are down, and some fingers + are in the button area, then the 2 coordinates reported + are for fingers outside the button area and these report + extra fingers being present in the right / left button + area. Note these fingers are not added to the F field! + so if a TWO packet is received and R = 1 then there are + 3 fingers down, etc. + TWO: 1: Two touches present, byte 0/4/5 are in TWO fmt + 0: If byte 4 bit 0 is 1, then byte 0/4/5 are in MULTI fmt + otherwise byte 0 bit 4 must be set and byte 0/4/5 are + in NEW fmt + F: Number of fingers - 3, 0 means 3 fingers, 1 means 4 ... + + +ALPS Absolute Mode - Protocol Version 8 +--------------------------------------- + +Spoken by SS4 (73 03 14) and SS5 (73 03 28) hardware. + +The packet type is given by the APD field, bits 4-5 of byte 3. + +Touchpad packet (APD = 0x2):: + + b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: SWM SWR SWL 1 1 0 0 X7 + byte 1: 0 X6 X5 X4 X3 X2 X1 X0 + byte 2: 0 Y6 Y5 Y4 Y3 Y2 Y1 Y0 + byte 3: 0 T&P 1 0 1 0 0 Y7 + byte 4: 0 Z6 Z5 Z4 Z3 Z2 Z1 Z0 + byte 5: 0 0 0 0 0 0 0 0 + +SWM, SWR, SWL: Middle, Right, and Left button states + +Touchpad 1 Finger packet (APD = 0x0):: + + b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: SWM SWR SWL 1 1 X2 X1 X0 + byte 1: X9 X8 X7 1 X6 X5 X4 X3 + byte 2: 0 X11 X10 LFB Y3 Y2 Y1 Y0 + byte 3: Y5 Y4 0 0 1 TAPF2 TAPF1 TAPF0 + byte 4: Zv7 Y11 Y10 1 Y9 Y8 Y7 Y6 + byte 5: Zv6 Zv5 Zv4 0 Zv3 Zv2 Zv1 Zv0 + +TAPF: ??? +LFB: ??? + +Touchpad 2 Finger packet (APD = 0x1):: + + b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: SWM SWR SWL 1 1 AX6 AX5 AX4 + byte 1: AX11 AX10 AX9 AX8 AX7 AZ1 AY4 AZ0 + byte 2: AY11 AY10 AY9 CONT AY8 AY7 AY6 AY5 + byte 3: 0 0 0 1 1 BX6 BX5 BX4 + byte 4: BX11 BX10 BX9 BX8 BX7 BZ1 BY4 BZ0 + byte 5: BY11 BY10 BY9 0 BY8 BY7 BY5 BY5 + +CONT: A 3-or-4 Finger packet is to follow + +Touchpad 3-or-4 Finger packet (APD = 0x3):: + + b7 b6 b5 b4 b3 b2 b1 b0 + byte 0: SWM SWR SWL 1 1 AX6 AX5 AX4 + byte 1: AX11 AX10 AX9 AX8 AX7 AZ1 AY4 AZ0 + byte 2: AY11 AY10 AY9 OVF AY8 AY7 AY6 AY5 + byte 3: 0 0 1 1 1 BX6 BX5 BX4 + byte 4: BX11 BX10 BX9 BX8 BX7 BZ1 BY4 BZ0 + byte 5: BY11 BY10 BY9 0 BY8 BY7 BY5 BY5 + +OVF: 5th finger detected diff --git a/Documentation/input/devices/amijoy.rst b/Documentation/input/devices/amijoy.rst new file mode 100644 index 000000000..8df7b11cd --- /dev/null +++ b/Documentation/input/devices/amijoy.rst @@ -0,0 +1,263 @@ +~~~~~~~~~~~~~~~~~~~~~~~~~ +Amiga joystick extensions +~~~~~~~~~~~~~~~~~~~~~~~~~ + + +Amiga 4-joystick parport extension +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Parallel port pins: + + +===== ======== ==== ========== +Pin Meaning Pin Meaning +===== ======== ==== ========== + 2 Up1 6 Up2 + 3 Down1 7 Down2 + 4 Left1 8 Left2 + 5 Right1 9 Right2 +13 Fire1 11 Fire2 +18 Gnd1 18 Gnd2 +===== ======== ==== ========== + +Amiga digital joystick pinout +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +=== ============ +Pin Meaning +=== ============ +1 Up +2 Down +3 Left +4 Right +5 n/c +6 Fire button +7 +5V (50mA) +8 Gnd +9 Thumb button +=== ============ + +Amiga mouse pinout +~~~~~~~~~~~~~~~~~~ + +=== ============ +Pin Meaning +=== ============ +1 V-pulse +2 H-pulse +3 VQ-pulse +4 HQ-pulse +5 Middle button +6 Left button +7 +5V (50mA) +8 Gnd +9 Right button +=== ============ + +Amiga analog joystick pinout +~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +=== ============== +Pin Meaning +=== ============== +1 Top button +2 Top2 button +3 Trigger button +4 Thumb button +5 Analog X +6 n/c +7 +5V (50mA) +8 Gnd +9 Analog Y +=== ============== + +Amiga lightpen pinout +~~~~~~~~~~~~~~~~~~~~~ + +=== ============= +Pin Meaning +=== ============= +1 n/c +2 n/c +3 n/c +4 n/c +5 Touch button +6 /Beamtrigger +7 +5V (50mA) +8 Gnd +9 Stylus button +=== ============= + +------------------------------------------------------------------------------- + +======== === ==== ==== ====== ======================================== +NAME rev ADDR type chip Description +======== === ==== ==== ====== ======================================== +JOY0DAT 00A R Denise Joystick-mouse 0 data (left vert, horiz) +JOY1DAT 00C R Denise Joystick-mouse 1 data (right vert,horiz) +======== === ==== ==== ====== ======================================== + + These addresses each read a 16 bit register. These in turn + are loaded from the MDAT serial stream and are clocked in on + the rising edge of SCLK. MLD output is used to parallel load + the external parallel-to-serial converter.This in turn is + loaded with the 4 quadrature inputs from each of two game + controller ports (8 total) plus 8 miscellaneous control bits + which are new for LISA and can be read in upper 8 bits of + LISAID. + + Register bits are as follows: + + - Mouse counter usage (pins 1,3 =Yclock, pins 2,4 =Xclock) + +======== === === === === === === === === ====== === === === === === === === + BIT# 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00 +======== === === === === === === === === ====== === === === === === === === +JOY0DAT Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0 X7 X6 X5 X4 X3 X2 X1 X0 +JOY1DAT Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0 X7 X6 X5 X4 X3 X2 X1 X0 +======== === === === === === === === === ====== === === === === === === === + + 0=LEFT CONTROLLER PAIR, 1=RIGHT CONTROLLER PAIR. + (4 counters total). The bit usage for both left and right + addresses is shown below. Each 6 bit counter (Y7-Y2,X7-X2) is + clocked by 2 of the signals input from the mouse serial + stream. Starting with first bit received: + + +-------------------+-----------------------------------------+ + | Serial | Bit Name | Description | + +========+==========+=========================================+ + | 0 | M0H | JOY0DAT Horizontal Clock | + +--------+----------+-----------------------------------------+ + | 1 | M0HQ | JOY0DAT Horizontal Clock (quadrature) | + +--------+----------+-----------------------------------------+ + | 2 | M0V | JOY0DAT Vertical Clock | + +--------+----------+-----------------------------------------+ + | 3 | M0VQ | JOY0DAT Vertical Clock (quadrature) | + +--------+----------+-----------------------------------------+ + | 4 | M1V | JOY1DAT Horizontal Clock | + +--------+----------+-----------------------------------------+ + | 5 | M1VQ | JOY1DAT Horizontal Clock (quadrature) | + +--------+----------+-----------------------------------------+ + | 6 | M1V | JOY1DAT Vertical Clock | + +--------+----------+-----------------------------------------+ + | 7 | M1VQ | JOY1DAT Vertical Clock (quadrature) | + +--------+----------+-----------------------------------------+ + + Bits 1 and 0 of each counter (Y1-Y0,X1-X0) may be + read to determine the state of the related input signal pair. + This allows these pins to double as joystick switch inputs. + Joystick switch closures can be deciphered as follows: + + +------------+------+---------------------------------+ + | Directions | Pin# | Counter bits | + +============+======+=================================+ + | Forward | 1 | Y1 xor Y0 (BIT#09 xor BIT#08) | + +------------+------+---------------------------------+ + | Left | 3 | Y1 | + +------------+------+---------------------------------+ + | Back | 2 | X1 xor X0 (BIT#01 xor BIT#00) | + +------------+------+---------------------------------+ + | Right | 4 | X1 | + +------------+------+---------------------------------+ + +------------------------------------------------------------------------------- + +======== === ==== ==== ====== ================================================= +NAME rev ADDR type chip Description +======== === ==== ==== ====== ================================================= +JOYTEST 036 W Denise Write to all 4 joystick-mouse counters at once. +======== === ==== ==== ====== ================================================= + + Mouse counter write test data: + +========= === === === === === === === === ====== === === === === === === === + BIT# 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00 +========= === === === === === === === === ====== === === === === === === === + JOYxDAT Y7 Y6 Y5 Y4 Y3 Y2 xx xx X7 X6 X5 X4 X3 X2 xx xx + JOYxDAT Y7 Y6 Y5 Y4 Y3 Y2 xx xx X7 X6 X5 X4 X3 X2 xx xx +========= === === === === === === === === ====== === === === === === === === + +------------------------------------------------------------------------------- + +======= === ==== ==== ====== ======================================== +NAME rev ADDR type chip Description +======= === ==== ==== ====== ======================================== +POT0DAT h 012 R Paula Pot counter data left pair (vert, horiz) +POT1DAT h 014 R Paula Pot counter data right pair (vert,horiz) +======= === ==== ==== ====== ======================================== + + These addresses each read a pair of 8 bit pot counters. + (4 counters total). The bit assignment for both + addresses is shown below. The counters are stopped by signals + from 2 controller connectors (left-right) with 2 pins each. + +====== === === === === === === === === ====== === === === === === === === + BIT# 15 14 13 12 11 10 09 08 07 06 05 04 03 02 01 00 +====== === === === === === === === === ====== === === === === === === === + RIGHT Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0 X7 X6 X5 X4 X3 X2 X1 X0 + LEFT Y7 Y6 Y5 Y4 Y3 Y2 Y1 Y0 X7 X6 X5 X4 X3 X2 X1 X0 +====== === === === === === === === === ====== === === === === === === === + + +--------------------------+-------+ + | CONNECTORS | PAULA | + +-------+------+-----+-----+-------+ + | Loc. | Dir. | Sym | pin | pin | + +=======+======+=====+=====+=======+ + | RIGHT | Y | RX | 9 | 33 | + +-------+------+-----+-----+-------+ + | RIGHT | X | RX | 5 | 32 | + +-------+------+-----+-----+-------+ + | LEFT | Y | LY | 9 | 36 | + +-------+------+-----+-----+-------+ + | LEFT | X | LX | 5 | 35 | + +-------+------+-----+-----+-------+ + + With normal (NTSC or PAL) horiz. line rate, the pots will + give a full scale (FF) reading with about 500kohms in one + frame time. With proportionally faster horiz line times, + the counters will count proportionally faster. + This should be noted when doing variable beam displays. + +------------------------------------------------------------------------------- + +====== === ==== ==== ====== ================================================ +NAME rev ADDR type chip Description +====== === ==== ==== ====== ================================================ +POTGO 034 W Paula Pot port (4 bit) bi-direction and data, and pot + counter start. +====== === ==== ==== ====== ================================================ + +------------------------------------------------------------------------------- + +====== === ==== ==== ====== ================================================ +NAME rev ADDR type chip Description +====== === ==== ==== ====== ================================================ +POTINP 016 R Paula Pot pin data read +====== === ==== ==== ====== ================================================ + + This register controls a 4 bit bi-direction I/O port + that shares the same 4 pins as the 4 pot counters above. + + +-------+----------+---------------------------------------------+ + | BIT# | FUNCTION | DESCRIPTION | + +=======+==========+=============================================+ + | 15 | OUTRY | Output enable for Paula pin 33 | + +-------+----------+---------------------------------------------+ + | 14 | DATRY | I/O data Paula pin 33 | + +-------+----------+---------------------------------------------+ + | 13 | OUTRX | Output enable for Paula pin 32 | + +-------+----------+---------------------------------------------+ + | 12 | DATRX | I/O data Paula pin 32 | + +-------+----------+---------------------------------------------+ + | 11 | OUTLY | Out put enable for Paula pin 36 | + +-------+----------+---------------------------------------------+ + | 10 | DATLY | I/O data Paula pin 36 | + +-------+----------+---------------------------------------------+ + | 09 | OUTLX | Output enable for Paula pin 35 | + +-------+----------+---------------------------------------------+ + | 08 | DATLX | I/O data Paula pin 35 | + +-------+----------+---------------------------------------------+ + | 07-01 | X | Not used | + +-------+----------+---------------------------------------------+ + | 00 | START | Start pots (dump capacitors,start counters) | + +-------+----------+---------------------------------------------+ diff --git a/Documentation/input/devices/appletouch.rst b/Documentation/input/devices/appletouch.rst new file mode 100644 index 000000000..c94470e66 --- /dev/null +++ b/Documentation/input/devices/appletouch.rst @@ -0,0 +1,94 @@ +.. include:: <isonum.txt> + +---------------------------------- +Apple Touchpad Driver (appletouch) +---------------------------------- + +:Copyright: |copy| 2005 Stelian Pop <stelian@popies.net> + +appletouch is a Linux kernel driver for the USB touchpad found on post +February 2005 and October 2005 Apple Aluminium Powerbooks. + +This driver is derived from Johannes Berg's appletrackpad driver [#f1]_, +but it has been improved in some areas: + + * appletouch is a full kernel driver, no userspace program is necessary + * appletouch can be interfaced with the synaptics X11 driver, in order + to have touchpad acceleration, scrolling, etc. + +Credits go to Johannes Berg for reverse-engineering the touchpad protocol, +Frank Arnold for further improvements, and Alex Harper for some additional +information about the inner workings of the touchpad sensors. Michael +Hanselmann added support for the October 2005 models. + +Usage +----- + +In order to use the touchpad in the basic mode, compile the driver and load +the module. A new input device will be detected and you will be able to read +the mouse data from /dev/input/mice (using gpm, or X11). + +In X11, you can configure the touchpad to use the synaptics X11 driver, which +will give additional functionalities, like acceleration, scrolling, 2 finger +tap for middle button mouse emulation, 3 finger tap for right button mouse +emulation, etc. In order to do this, make sure you're using a recent version of +the synaptics driver (tested with 0.14.2, available from [#f2]_), and configure +a new input device in your X11 configuration file (take a look below for an +example). For additional configuration, see the synaptics driver documentation:: + + Section "InputDevice" + Identifier "Synaptics Touchpad" + Driver "synaptics" + Option "SendCoreEvents" "true" + Option "Device" "/dev/input/mice" + Option "Protocol" "auto-dev" + Option "LeftEdge" "0" + Option "RightEdge" "850" + Option "TopEdge" "0" + Option "BottomEdge" "645" + Option "MinSpeed" "0.4" + Option "MaxSpeed" "1" + Option "AccelFactor" "0.02" + Option "FingerLow" "0" + Option "FingerHigh" "30" + Option "MaxTapMove" "20" + Option "MaxTapTime" "100" + Option "HorizScrollDelta" "0" + Option "VertScrollDelta" "30" + Option "SHMConfig" "on" + EndSection + + Section "ServerLayout" + ... + InputDevice "Mouse" + InputDevice "Synaptics Touchpad" + ... + EndSection + +Fuzz problems +------------- + +The touchpad sensors are very sensitive to heat, and will generate a lot of +noise when the temperature changes. This is especially true when you power-on +the laptop for the first time. + +The appletouch driver tries to handle this noise and auto adapt itself, but it +is not perfect. If finger movements are not recognized anymore, try reloading +the driver. + +You can activate debugging using the 'debug' module parameter. A value of 0 +deactivates any debugging, 1 activates tracing of invalid samples, 2 activates +full tracing (each sample is being traced):: + + modprobe appletouch debug=1 + +or:: + + echo "1" > /sys/module/appletouch/parameters/debug + + +.. Links: + +.. [#f1] http://johannes.sipsolutions.net/PowerBook/touchpad/ + +.. [#f2] `<http://web.archive.org/web/*/http://web.telia.com/~u89404340/touchpad/index.html>`_ diff --git a/Documentation/input/devices/atarikbd.rst b/Documentation/input/devices/atarikbd.rst new file mode 100644 index 000000000..0c4c7804c --- /dev/null +++ b/Documentation/input/devices/atarikbd.rst @@ -0,0 +1,820 @@ +==================================== +Intelligent Keyboard (ikbd) Protocol +==================================== + + +Introduction +============ + +The Atari Corp. Intelligent Keyboard (ikbd) is a general purpose keyboard +controller that is flexible enough that it can be used in a variety of +products without modification. The keyboard, with its microcontroller, +provides a convenient connection point for a mouse and switch-type joysticks. +The ikbd processor also maintains a time-of-day clock with one second +resolution. +The ikbd has been designed to be general enough that it can be used with a +variety of new computer products. Product variations in a number of +keyswitches, mouse resolution, etc. can be accommodated. +The ikbd communicates with the main processor over a high speed bi-directional +serial interface. It can function in a variety of modes to facilitate +different applications of the keyboard, joysticks, or mouse. Limited use of +the controller is possible in applications in which only a unidirectional +communications medium is available by carefully designing the default modes. + +Keyboard +======== + +The keyboard always returns key make/break scan codes. The ikbd generates +keyboard scan codes for each key press and release. The key scan make (key +closure) codes start at 1, and are defined in Appendix A. For example, the +ISO key position in the scan code table should exist even if no keyswitch +exists in that position on a particular keyboard. The break code for each key +is obtained by ORing 0x80 with the make code. + +The special codes 0xF6 through 0xFF are reserved for use as follows: + +=================== ==================================================== + Code Command +=================== ==================================================== + 0xF6 status report + 0xF7 absolute mouse position record + 0xF8-0xFB relative mouse position records (lsbs determined by + mouse button states) + 0xFC time-of-day + 0xFD joystick report (both sticks) + 0xFE joystick 0 event + 0xFF joystick 1 event +=================== ==================================================== + +The two shift keys return different scan codes in this mode. The ENTER key +and the RETurn key are also distinct. + +Mouse +===== + +The mouse port should be capable of supporting a mouse with resolution of +approximately 200 counts (phase changes or 'clicks') per inch of travel. The +mouse should be scanned at a rate that will permit accurate tracking at +velocities up to 10 inches per second. +The ikbd can report mouse motion in three distinctly different ways. It can +report relative motion, absolute motion in a coordinate system maintained +within the ikbd, or by converting mouse motion into keyboard cursor control +key equivalents. +The mouse buttons can be treated as part of the mouse or as additional +keyboard keys. + +Relative Position Reporting +--------------------------- + +In relative position mode, the ikbd will return relative mouse position +records whenever a mouse event occurs. A mouse event consists of a mouse +button being pressed or released, or motion in either axis exceeding a +settable threshold of motion. Regardless of the threshold, all bits of +resolution are returned to the host computer. +Note that the ikbd may return mouse relative position reports with +significantly more than the threshold delta x or y. This may happen since no +relative mouse motion events will be generated: (a) while the keyboard has +been 'paused' ( the event will be stored until keyboard communications is +resumed) (b) while any event is being transmitted. + +The relative mouse position record is a three byte record of the form +(regardless of keyboard mode):: + + %111110xy ; mouse position record flag + ; where y is the right button state + ; and x is the left button state + X ; delta x as twos complement integer + Y ; delta y as twos complement integer + +Note that the value of the button state bits should be valid even if the +MOUSE BUTTON ACTION has set the buttons to act like part of the keyboard. +If the accumulated motion before the report packet is generated exceeds the ++127...-128 range, the motion is broken into multiple packets. +Note that the sign of the delta y reported is a function of the Y origin +selected. + +Absolute Position reporting +--------------------------- + +The ikbd can also maintain absolute mouse position. Commands exist for +resetting the mouse position, setting X/Y scaling, and interrogating the +current mouse position. + +Mouse Cursor Key Mode +--------------------- + +The ikbd can translate mouse motion into the equivalent cursor keystrokes. +The number of mouse clicks per keystroke is independently programmable in +each axis. The ikbd internally maintains mouse motion information to the +highest resolution available, and merely generates a pair of cursor key events +for each multiple of the scale factor. +Mouse motion produces the cursor key make code immediately followed by the +break code for the appropriate cursor key. The mouse buttons produce scan +codes above those normally assigned for the largest envisioned keyboard (i.e. +LEFT=0x74 & RIGHT=0x75). + +Joystick +======== + +Joystick Event Reporting +------------------------ + +In this mode, the ikbd generates a record whenever the joystick position is +changed (i.e. for each opening or closing of a joystick switch or trigger). + +The joystick event record is two bytes of the form:: + + %1111111x ; Joystick event marker + ; where x is Joystick 0 or 1 + %x000yyyy ; where yyyy is the stick position + ; and x is the trigger + +Joystick Interrogation +---------------------- + +The current state of the joystick ports may be interrogated at any time in +this mode by sending an 'Interrogate Joystick' command to the ikbd. + +The ikbd response to joystick interrogation is a three byte report of the form:: + + 0xFD ; joystick report header + %x000yyyy ; Joystick 0 + %x000yyyy ; Joystick 1 + ; where x is the trigger + ; and yyy is the stick position + +Joystick Monitoring +------------------- + +A mode is available that devotes nearly all of the keyboard communications +time to reporting the state of the joystick ports at a user specifiable rate. +It remains in this mode until reset or commanded into another mode. The PAUSE +command in this mode not only stop the output but also temporarily stops +scanning the joysticks (samples are not queued). + +Fire Button Monitoring +---------------------- + +A mode is provided to permit monitoring a single input bit at a high rate. In +this mode the ikbd monitors the state of the Joystick 1 fire button at the +maximum rate permitted by the serial communication channel. The data is packed +8 bits per byte for transmission to the host. The ikbd remains in this mode +until reset or commanded into another mode. The PAUSE command in this mode not +only stops the output but also temporarily stops scanning the button (samples +are not queued). + +Joystick Key Code Mode +---------------------- + +The ikbd may be commanded to translate the use of either joystick into the +equivalent cursor control keystroke(s). The ikbd provides a single breakpoint +velocity joystick cursor. +Joystick events produce the make code, immediately followed by the break code +for the appropriate cursor motion keys. The trigger or fire buttons of the +joysticks produce pseudo key scan codes above those used by the largest key +matrix envisioned (i.e. JOYSTICK0=0x74, JOYSTICK1=0x75). + +Time-of-Day Clock +================= + +The ikbd also maintains a time-of-day clock for the system. Commands are +available to set and interrogate the timer-of-day clock. Time-keeping is +maintained down to a resolution of one second. + +Status Inquiries +================ + +The current state of ikbd modes and parameters may be found by sending status +inquiry commands that correspond to the ikbd set commands. + +Power-Up Mode +============= + +The keyboard controller will perform a simple self-test on power-up to detect +major controller faults (ROM checksum and RAM test) and such things as stuck +keys. Any keys down at power-up are presumed to be stuck, and their BREAK +(sic) code is returned (which without the preceding MAKE code is a flag for a +keyboard error). If the controller self-test completes without error, the code +0xF0 is returned. (This code will be used to indicate the version/release of +the ikbd controller. The first release of the ikbd is version 0xF0, should +there be a second release it will be 0xF1, and so on.) +The ikbd defaults to a mouse position reporting with threshold of 1 unit in +either axis and the Y=0 origin at the top of the screen, and joystick event +reporting mode for joystick 1, with both buttons being logically assigned to +the mouse. After any joystick command, the ikbd assumes that joysticks are +connected to both Joystick0 and Joystick1. Any mouse command (except MOUSE +DISABLE) then causes port 0 to again be scanned as if it were a mouse, and +both buttons are logically connected to it. If a mouse disable command is +received while port 0 is presumed to be a mouse, the button is logically +assigned to Joystick1 (until the mouse is reenabled by another mouse command). + +ikbd Command Set +================ + +This section contains a list of commands that can be sent to the ikbd. Command +codes (such as 0x00) which are not specified should perform no operation +(NOPs). + +RESET +----- + +:: + + 0x80 + 0x01 + +N.B. The RESET command is the only two byte command understood by the ikbd. +Any byte following an 0x80 command byte other than 0x01 is ignored (and causes +the 0x80 to be ignored). +A reset may also be caused by sending a break lasting at least 200mS to the +ikbd. +Executing the RESET command returns the keyboard to its default (power-up) +mode and parameter settings. It does not affect the time-of-day clock. +The RESET command or function causes the ikbd to perform a simple self-test. +If the test is successful, the ikbd will send the code of 0xF0 within 300mS +of receipt of the RESET command (or the end of the break, or power-up). The +ikbd will then scan the key matrix for any stuck (closed) keys. Any keys found +closed will cause the break scan code to be generated (the break code arriving +without being preceded by the make code is a flag for a key matrix error). + +SET MOUSE BUTTON ACTION +----------------------- + +:: + + 0x07 + %00000mss ; mouse button action + ; (m is presumed = 1 when in MOUSE KEYCODE mode) + ; mss=0xy, mouse button press or release causes mouse + ; position report + ; where y=1, mouse key press causes absolute report + ; and x=1, mouse key release causes absolute report + ; mss=100, mouse buttons act like keys + +This command sets how the ikbd should treat the buttons on the mouse. The +default mouse button action mode is %00000000, the buttons are treated as part +of the mouse logically. +When buttons act like keys, LEFT=0x74 & RIGHT=0x75. + +SET RELATIVE MOUSE POSITION REPORTING +------------------------------------- + +:: + + 0x08 + +Set relative mouse position reporting. (DEFAULT) Mouse position packets are +generated asynchronously by the ikbd whenever motion exceeds the setable +threshold in either axis (see SET MOUSE THRESHOLD). Depending upon the mouse +key mode, mouse position reports may also be generated when either mouse +button is pressed or released. Otherwise the mouse buttons behave as if they +were keyboard keys. + +SET ABSOLUTE MOUSE POSITIONING +------------------------------ + +:: + + 0x09 + XMSB ; X maximum (in scaled mouse clicks) + XLSB + YMSB ; Y maximum (in scaled mouse clicks) + YLSB + +Set absolute mouse position maintenance. Resets the ikbd maintained X and Y +coordinates. +In this mode, the value of the internally maintained coordinates does NOT wrap +between 0 and large positive numbers. Excess motion below 0 is ignored. The +command sets the maximum positive value that can be attained in the scaled +coordinate system. Motion beyond that value is also ignored. + +SET MOUSE KEYCODE MODE +---------------------- + +:: + + 0x0A + deltax ; distance in X clicks to return (LEFT) or (RIGHT) + deltay ; distance in Y clicks to return (UP) or (DOWN) + +Set mouse monitoring routines to return cursor motion keycodes instead of +either RELATIVE or ABSOLUTE motion records. The ikbd returns the appropriate +cursor keycode after mouse travel exceeding the user specified deltas in +either axis. When the keyboard is in key scan code mode, mouse motion will +cause the make code immediately followed by the break code. Note that this +command is not affected by the mouse motion origin. + +SET MOUSE THRESHOLD +------------------- + +:: + + 0x0B + X ; x threshold in mouse ticks (positive integers) + Y ; y threshold in mouse ticks (positive integers) + +This command sets the threshold before a mouse event is generated. Note that +it does NOT affect the resolution of the data returned to the host. This +command is valid only in RELATIVE MOUSE POSITIONING mode. The thresholds +default to 1 at RESET (or power-up). + +SET MOUSE SCALE +--------------- + +:: + + 0x0C + X ; horizontal mouse ticks per internal X + Y ; vertical mouse ticks per internal Y + +This command sets the scale factor for the ABSOLUTE MOUSE POSITIONING mode. +In this mode, the specified number of mouse phase changes ('clicks') must +occur before the internally maintained coordinate is changed by one +(independently scaled for each axis). Remember that the mouse position +information is available only by interrogating the ikbd in the ABSOLUTE MOUSE +POSITIONING mode unless the ikbd has been commanded to report on button press +or release (see SET MOUSE BUTTON ACTION). + +INTERROGATE MOUSE POSITION +-------------------------- + +:: + + 0x0D + Returns: + 0xF7 ; absolute mouse position header + BUTTONS + 0000dcba ; where a is right button down since last interrogation + ; b is right button up since last + ; c is left button down since last + ; d is left button up since last + XMSB ; X coordinate + XLSB + YMSB ; Y coordinate + YLSB + +The INTERROGATE MOUSE POSITION command is valid when in the ABSOLUTE MOUSE +POSITIONING mode, regardless of the setting of the MOUSE BUTTON ACTION. + +LOAD MOUSE POSITION +------------------- + +:: + + 0x0E + 0x00 ; filler + XMSB ; X coordinate + XLSB ; (in scaled coordinate system) + YMSB ; Y coordinate + YLSB + +This command allows the user to preset the internally maintained absolute +mouse position. + +SET Y=0 AT BOTTOM +----------------- + +:: + + 0x0F + +This command makes the origin of the Y axis to be at the bottom of the +logical coordinate system internal to the ikbd for all relative or absolute +mouse motion. This causes mouse motion toward the user to be negative in sign +and away from the user to be positive. + +SET Y=0 AT TOP +-------------- + +:: + + 0x10 + +Makes the origin of the Y axis to be at the top of the logical coordinate +system within the ikbd for all relative or absolute mouse motion. (DEFAULT) +This causes mouse motion toward the user to be positive in sign and away from +the user to be negative. + +RESUME +------ + +:: + + 0x11 + +Resume sending data to the host. Since any command received by the ikbd after +its output has been paused also causes an implicit RESUME this command can be +thought of as a NO OPERATION command. If this command is received by the ikbd +and it is not PAUSED, it is simply ignored. + +DISABLE MOUSE +------------- + +:: + + 0x12 + +All mouse event reporting is disabled (and scanning may be internally +disabled). Any valid mouse mode command resumes mouse motion monitoring. (The +valid mouse mode commands are SET RELATIVE MOUSE POSITION REPORTING, SET +ABSOLUTE MOUSE POSITIONING, and SET MOUSE KEYCODE MODE. ) +N.B. If the mouse buttons have been commanded to act like keyboard keys, this +command DOES affect their actions. + +PAUSE OUTPUT +------------ + +:: + + 0x13 + +Stop sending data to the host until another valid command is received. Key +matrix activity is still monitored and scan codes or ASCII characters enqueued +(up to the maximum supported by the microcontroller) to be sent when the host +allows the output to be resumed. If in the JOYSTICK EVENT REPORTING mode, +joystick events are also queued. +Mouse motion should be accumulated while the output is paused. If the ikbd is +in RELATIVE MOUSE POSITIONING REPORTING mode, motion is accumulated beyond the +normal threshold limits to produce the minimum number of packets necessary for +transmission when output is resumed. Pressing or releasing either mouse button +causes any accumulated motion to be immediately queued as packets, if the +mouse is in RELATIVE MOUSE POSITION REPORTING mode. +Because of the limitations of the microcontroller memory this command should +be used sparingly, and the output should not be shut of for more than <tbd> +milliseconds at a time. +The output is stopped only at the end of the current 'even'. If the PAUSE +OUTPUT command is received in the middle of a multiple byte report, the packet +will still be transmitted to conclusion and then the PAUSE will take effect. +When the ikbd is in either the JOYSTICK MONITORING mode or the FIRE BUTTON +MONITORING mode, the PAUSE OUTPUT command also temporarily stops the +monitoring process (i.e. the samples are not enqueued for transmission). + +SET JOYSTICK EVENT REPORTING +---------------------------- + +:: + + 0x14 + +Enter JOYSTICK EVENT REPORTING mode (DEFAULT). Each opening or closure of a +joystick switch or trigger causes a joystick event record to be generated. + +SET JOYSTICK INTERROGATION MODE +------------------------------- + +:: + + 0x15 + +Disables JOYSTICK EVENT REPORTING. Host must send individual JOYSTICK +INTERROGATE commands to sense joystick state. + +JOYSTICK INTERROGATE +-------------------- + +:: + + 0x16 + +Return a record indicating the current state of the joysticks. This command +is valid in either the JOYSTICK EVENT REPORTING mode or the JOYSTICK +INTERROGATION MODE. + +SET JOYSTICK MONITORING +----------------------- + +:: + + 0x17 + rate ; time between samples in hundredths of a second + Returns: (in packets of two as long as in mode) + %000000xy ; where y is JOYSTICK1 Fire button + ; and x is JOYSTICK0 Fire button + %nnnnmmmm ; where m is JOYSTICK1 state + ; and n is JOYSTICK0 state + +Sets the ikbd to do nothing but monitor the serial command line, maintain the +time-of-day clock, and monitor the joystick. The rate sets the interval +between joystick samples. +N.B. The user should not set the rate higher than the serial communications +channel will allow the 2 bytes packets to be transmitted. + +SET FIRE BUTTON MONITORING +-------------------------- + +:: + + 0x18 + Returns: (as long as in mode) + %bbbbbbbb ; state of the JOYSTICK1 fire button packed + ; 8 bits per byte, the first sample if the MSB + +Set the ikbd to do nothing but monitor the serial command line, maintain the +time-of-day clock, and monitor the fire button on Joystick 1. The fire button +is scanned at a rate that causes 8 samples to be made in the time it takes for +the previous byte to be sent to the host (i.e. scan rate = 8/10 * baud rate). +The sample interval should be as constant as possible. + +SET JOYSTICK KEYCODE MODE +------------------------- + +:: + + 0x19 + RX ; length of time (in tenths of seconds) until + ; horizontal velocity breakpoint is reached + RY ; length of time (in tenths of seconds) until + ; vertical velocity breakpoint is reached + TX ; length (in tenths of seconds) of joystick closure + ; until horizontal cursor key is generated before RX + ; has elapsed + TY ; length (in tenths of seconds) of joystick closure + ; until vertical cursor key is generated before RY + ; has elapsed + VX ; length (in tenths of seconds) of joystick closure + ; until horizontal cursor keystrokes are generated + ; after RX has elapsed + VY ; length (in tenths of seconds) of joystick closure + ; until vertical cursor keystrokes are generated + ; after RY has elapsed + +In this mode, joystick 0 is scanned in a way that simulates cursor keystrokes. +On initial closure, a keystroke pair (make/break) is generated. Then up to Rn +tenths of seconds later, keystroke pairs are generated every Tn tenths of +seconds. After the Rn breakpoint is reached, keystroke pairs are generated +every Vn tenths of seconds. This provides a velocity (auto-repeat) breakpoint +feature. +Note that by setting RX and/or Ry to zero, the velocity feature can be +disabled. The values of TX and TY then become meaningless, and the generation +of cursor 'keystrokes' is set by VX and VY. + +DISABLE JOYSTICKS +----------------- + +:: + + 0x1A + +Disable the generation of any joystick events (and scanning may be internally +disabled). Any valid joystick mode command resumes joystick monitoring. (The +joystick mode commands are SET JOYSTICK EVENT REPORTING, SET JOYSTICK +INTERROGATION MODE, SET JOYSTICK MONITORING, SET FIRE BUTTON MONITORING, and +SET JOYSTICK KEYCODE MODE.) + +TIME-OF-DAY CLOCK SET +--------------------- + +:: + + 0x1B + YY ; year (2 least significant digits) + MM ; month + DD ; day + hh ; hour + mm ; minute + ss ; second + +All time-of-day data should be sent to the ikbd in packed BCD format. +Any digit that is not a valid BCD digit should be treated as a 'don't care' +and not alter that particular field of the date or time. This permits setting +only some subfields of the time-of-day clock. + +INTERROGATE TIME-OF-DAT CLOCK +----------------------------- + +:: + + 0x1C + Returns: + 0xFC ; time-of-day event header + YY ; year (2 least significant digits) + MM ; month + DD ; day + hh ; hour + mm ; minute + ss ; second + + All time-of-day is sent in packed BCD format. + +MEMORY LOAD +----------- + +:: + + 0x20 + ADRMSB ; address in controller + ADRLSB ; memory to be loaded + NUM ; number of bytes (0-128) + { data } + +This command permits the host to load arbitrary values into the ikbd +controller memory. The time between data bytes must be less than 20ms. + +MEMORY READ +----------- + +:: + + 0x21 + ADRMSB ; address in controller + ADRLSB ; memory to be read + Returns: + 0xF6 ; status header + 0x20 ; memory access + { data } ; 6 data bytes starting at ADR + +This command permits the host to read from the ikbd controller memory. + +CONTROLLER EXECUTE +------------------ + +:: + + 0x22 + ADRMSB ; address of subroutine in + ADRLSB ; controller memory to be called + +This command allows the host to command the execution of a subroutine in the +ikbd controller memory. + +STATUS INQUIRIES +---------------- + +:: + + Status commands are formed by inclusively ORing 0x80 with the + relevant SET command. + + Example: + 0x88 (or 0x89 or 0x8A) ; request mouse mode + Returns: + 0xF6 ; status response header + mode ; 0x08 is RELATIVE + ; 0x09 is ABSOLUTE + ; 0x0A is KEYCODE + param1 ; 0 is RELATIVE + ; XMSB maximum if ABSOLUTE + ; DELTA X is KEYCODE + param2 ; 0 is RELATIVE + ; YMSB maximum if ABSOLUTE + ; DELTA Y is KEYCODE + param3 ; 0 if RELATIVE + ; or KEYCODE + ; YMSB is ABSOLUTE + param4 ; 0 if RELATIVE + ; or KEYCODE + ; YLSB is ABSOLUTE + 0 ; pad + 0 + +The STATUS INQUIRY commands request the ikbd to return either the current mode +or the parameters associated with a given command. All status reports are +padded to form 8 byte long return packets. The responses to the status +requests are designed so that the host may store them away (after stripping +off the status report header byte) and later send them back as commands to +ikbd to restore its state. The 0 pad bytes will be treated as NOPs by the +ikbd. + + Valid STATUS INQUIRY commands are:: + + 0x87 mouse button action + 0x88 mouse mode + 0x89 + 0x8A + 0x8B mnouse threshold + 0x8C mouse scale + 0x8F mouse vertical coordinates + 0x90 ( returns 0x0F Y=0 at bottom + 0x10 Y=0 at top ) + 0x92 mouse enable/disable + ( returns 0x00 enabled) + 0x12 disabled ) + 0x94 joystick mode + 0x95 + 0x96 + 0x9A joystick enable/disable + ( returns 0x00 enabled + 0x1A disabled ) + +It is the (host) programmer's responsibility to have only one unanswered +inquiry in process at a time. +STATUS INQUIRY commands are not valid if the ikbd is in JOYSTICK MONITORING +mode or FIRE BUTTON MONITORING mode. + + +SCAN CODES +========== + +The key scan codes returned by the ikbd are chosen to simplify the +implementation of GSX. + +GSX Standard Keyboard Mapping + +======= ============ +Hex Keytop +======= ============ +01 Esc +02 1 +03 2 +04 3 +05 4 +06 5 +07 6 +08 7 +09 8 +0A 9 +0B 0 +0C \- +0D \= +0E BS +0F TAB +10 Q +11 W +12 E +13 R +14 T +15 Y +16 U +17 I +18 O +19 P +1A [ +1B ] +1C RET +1D CTRL +1E A +1F S +20 D +21 F +22 G +23 H +24 J +25 K +26 L +27 ; +28 ' +29 \` +2A (LEFT) SHIFT +2B \\ +2C Z +2D X +2E C +2F V +30 B +31 N +32 M +33 , +34 . +35 / +36 (RIGHT) SHIFT +37 { NOT USED } +38 ALT +39 SPACE BAR +3A CAPS LOCK +3B F1 +3C F2 +3D F3 +3E F4 +3F F5 +40 F6 +41 F7 +42 F8 +43 F9 +44 F10 +45 { NOT USED } +46 { NOT USED } +47 HOME +48 UP ARROW +49 { NOT USED } +4A KEYPAD - +4B LEFT ARROW +4C { NOT USED } +4D RIGHT ARROW +4E KEYPAD + +4F { NOT USED } +50 DOWN ARROW +51 { NOT USED } +52 INSERT +53 DEL +54 { NOT USED } +5F { NOT USED } +60 ISO KEY +61 UNDO +62 HELP +63 KEYPAD ( +64 KEYPAD / +65 KEYPAD * +66 KEYPAD * +67 KEYPAD 7 +68 KEYPAD 8 +69 KEYPAD 9 +6A KEYPAD 4 +6B KEYPAD 5 +6C KEYPAD 6 +6D KEYPAD 1 +6E KEYPAD 2 +6F KEYPAD 3 +70 KEYPAD 0 +71 KEYPAD . +72 KEYPAD ENTER +======= ============ diff --git a/Documentation/input/devices/bcm5974.rst b/Documentation/input/devices/bcm5974.rst new file mode 100644 index 000000000..4aca199b0 --- /dev/null +++ b/Documentation/input/devices/bcm5974.rst @@ -0,0 +1,70 @@ +.. include:: <isonum.txt> + +------------------------ +BCM5974 Driver (bcm5974) +------------------------ + +:Copyright: |copy| 2008-2009 Henrik Rydberg <rydberg@euromail.se> + +The USB initialization and package decoding was made by Scott Shawcroft as +part of the touchd user-space driver project: + +:Copyright: |copy| 2008 Scott Shawcroft (scott.shawcroft@gmail.com) + +The BCM5974 driver is based on the appletouch driver: + +:Copyright: |copy| 2001-2004 Greg Kroah-Hartman (greg@kroah.com) +:Copyright: |copy| 2005 Johannes Berg (johannes@sipsolutions.net) +:Copyright: |copy| 2005 Stelian Pop (stelian@popies.net) +:Copyright: |copy| 2005 Frank Arnold (frank@scirocco-5v-turbo.de) +:Copyright: |copy| 2005 Peter Osterlund (petero2@telia.com) +:Copyright: |copy| 2005 Michael Hanselmann (linux-kernel@hansmi.ch) +:Copyright: |copy| 2006 Nicolas Boichat (nicolas@boichat.ch) + +This driver adds support for the multi-touch trackpad on the new Apple +Macbook Air and Macbook Pro laptops. It replaces the appletouch driver on +those computers, and integrates well with the synaptics driver of the Xorg +system. + +Known to work on Macbook Air, Macbook Pro Penryn and the new unibody +Macbook 5 and Macbook Pro 5. + +Usage +----- + +The driver loads automatically for the supported usb device ids, and +becomes available both as an event device (/dev/input/event*) and as a +mouse via the mousedev driver (/dev/input/mice). + +USB Race +-------- + +The Apple multi-touch trackpads report both mouse and keyboard events via +different interfaces of the same usb device. This creates a race condition +with the HID driver, which, if not told otherwise, will find the standard +HID mouse and keyboard, and claim the whole device. To remedy, the usb +product id must be listed in the mouse_ignore list of the hid driver. + +Debug output +------------ + +To ease the development for new hardware version, verbose packet output can +be switched on with the debug kernel module parameter. The range [1-9] +yields different levels of verbosity. Example (as root):: + + echo -n 9 > /sys/module/bcm5974/parameters/debug + + tail -f /var/log/debug + + echo -n 0 > /sys/module/bcm5974/parameters/debug + +Trivia +------ + +The driver was developed at the ubuntu forums in June 2008 [#f1]_, and now has +a more permanent home at bitmath.org [#f2]_. + +.. Links + +.. [#f1] http://ubuntuforums.org/showthread.php?t=840040 +.. [#f2] http://bitmath.org/code/ diff --git a/Documentation/input/devices/cma3000_d0x.rst b/Documentation/input/devices/cma3000_d0x.rst new file mode 100644 index 000000000..8bc8e6148 --- /dev/null +++ b/Documentation/input/devices/cma3000_d0x.rst @@ -0,0 +1,139 @@ +CMA3000-D0x Accelerometer +========================= + +Supported chips: +* VTI CMA3000-D0x + +Datasheet: + CMA3000-D0X Product Family Specification 8281000A.02.pdf + <http://www.vti.fi/en/> + +:Author: Hemanth V <hemanthv@ti.com> + + +Description +----------- + +CMA3000 Tri-axis accelerometer supports Motion detect, Measurement and +Free fall modes. + +Motion Detect Mode: + Its the low power mode where interrupts are generated only + when motion exceeds the defined thresholds. + +Measurement Mode: + This mode is used to read the acceleration data on X,Y,Z + axis and supports 400, 100, 40 Hz sample frequency. + +Free fall Mode: + This mode is intended to save system resources. + +Threshold values: + Chip supports defining threshold values for above modes + which includes time and g value. Refer product specifications for + more details. + +CMA3000 chip supports mutually exclusive I2C and SPI interfaces for +communication, currently the driver supports I2C based communication only. +Initial configuration for bus mode is set in non volatile memory and can later +be modified through bus interface command. + +Driver reports acceleration data through input subsystem. It generates ABS_MISC +event with value 1 when free fall is detected. + +Platform data need to be configured for initial default values. + +Platform Data +------------- + +fuzz_x: + Noise on X Axis + +fuzz_y: + Noise on Y Axis + +fuzz_z: + Noise on Z Axis + +g_range: + G range in milli g i.e 2000 or 8000 + +mode: + Default Operating mode + +mdthr: + Motion detect g range threshold value + +mdfftmr: + Motion detect and free fall time threshold value + +ffthr: + Free fall g range threshold value + +Input Interface +--------------- + +Input driver version is 1.0.0 +Input device ID: bus 0x18 vendor 0x0 product 0x0 version 0x0 +Input device name: "cma3000-accelerometer" + +Supported events:: + + Event type 0 (Sync) + Event type 3 (Absolute) + Event code 0 (X) + Value 47 + Min -8000 + Max 8000 + Fuzz 200 + Event code 1 (Y) + Value -28 + Min -8000 + Max 8000 + Fuzz 200 + Event code 2 (Z) + Value 905 + Min -8000 + Max 8000 + Fuzz 200 + Event code 40 (Misc) + Value 0 + Min 0 + Max 1 + Event type 4 (Misc) + + +Register/Platform parameters Description +---------------------------------------- + +mode:: + + 0: power down mode + 1: 100 Hz Measurement mode + 2: 400 Hz Measurement mode + 3: 40 Hz Measurement mode + 4: Motion Detect mode (default) + 5: 100 Hz Free fall mode + 6: 40 Hz Free fall mode + 7: Power off mode + +grange:: + + 2000: 2000 mg or 2G Range + 8000: 8000 mg or 8G Range + +mdthr:: + + X: X * 71mg (8G Range) + X: X * 18mg (2G Range) + +mdfftmr:: + + X: (X & 0x70) * 100 ms (MDTMR) + (X & 0x0F) * 2.5 ms (FFTMR 400 Hz) + (X & 0x0F) * 10 ms (FFTMR 100 Hz) + +ffthr:: + + X: (X >> 2) * 18mg (2G Range) + X: (X & 0x0F) * 71 mg (8G Range) diff --git a/Documentation/input/devices/cs461x.rst b/Documentation/input/devices/cs461x.rst new file mode 100644 index 000000000..b1e6d508a --- /dev/null +++ b/Documentation/input/devices/cs461x.rst @@ -0,0 +1,43 @@ +Crystal SoundFusion CS4610/CS4612/CS461 joystick +================================================ + +This is a new low-level driver to support analog joystick attached to +Crystal SoundFusion CS4610/CS4612/CS4615. This code is based upon +Vortex/Solo drivers as an example of decoration style, and ALSA +0.5.8a kernel drivers as an chipset documentation and samples. + +This version does not have cooked mode support; the basic code +is present here, but have not tested completely. The button analysis +is completed in this mode, but the axis movement is not. + +Raw mode works fine with analog joystick front-end driver and cs461x +driver as a backend. I've tested this driver with CS4610, 4-axis and +4-button joystick; I mean the jstest utility. Also I've tried to +play in xracer game using joystick, and the result is better than +keyboard only mode. + +The sensitivity and calibrate quality have not been tested; the two +reasons are performed: the same hardware cannot work under Win95 (blue +screen in VJOYD); I have no documentation on my chip; and the existing +behavior in my case was not raised the requirement of joystick calibration. +So the driver have no code to perform hardware related calibration. + +This driver have the basic support for PCI devices only; there is no +ISA or PnP ISA cards supported. + +The driver works with ALSA drivers simultaneously. For example, the xracer +uses joystick as input device and PCM device as sound output in one time. +There are no sound or input collisions detected. The source code have +comments about them; but I've found the joystick can be initialized +separately of ALSA modules. So, you can use only one joystick driver +without ALSA drivers. The ALSA drivers are not needed to compile or +run this driver. + +There are no debug information print have been placed in source, and no +specific options required to work this driver. The found chipset parameters +are printed via printk(KERN_INFO "..."), see the /var/log/messages to +inspect cs461x: prefixed messages to determine possible card detection +errors. + +Regards, +Viktor diff --git a/Documentation/input/devices/edt-ft5x06.rst b/Documentation/input/devices/edt-ft5x06.rst new file mode 100644 index 000000000..1ccc94b19 --- /dev/null +++ b/Documentation/input/devices/edt-ft5x06.rst @@ -0,0 +1,54 @@ +EDT ft5x06 based Polytouch devices +---------------------------------- + +The edt-ft5x06 driver is useful for the EDT "Polytouch" family of capacitive +touch screens. Note that it is *not* suitable for other devices based on the +focaltec ft5x06 devices, since they contain vendor-specific firmware. In +particular this driver is not suitable for the Nook tablet. + +It has been tested with the following devices: + * EP0350M06 + * EP0430M06 + * EP0570M06 + * EP0700M06 + +The driver allows configuration of the touch screen via a set of sysfs files: + +/sys/class/input/eventX/device/device/threshold: + allows setting the "click"-threshold in the range from 0 to 80. + +/sys/class/input/eventX/device/device/gain: + allows setting the sensitivity in the range from 0 to 31. Note that + lower values indicate higher sensitivity. + +/sys/class/input/eventX/device/device/offset: + allows setting the edge compensation in the range from 0 to 31. + +/sys/class/input/eventX/device/device/report_rate: + allows setting the report rate in the range from 3 to 14. + + +For debugging purposes the driver provides a few files in the debug +filesystem (if available in the kernel). In /sys/kernel/debug/edt_ft5x06 +you'll find the following files: + +num_x, num_y: + (readonly) contains the number of sensor fields in X- and + Y-direction. + +mode: + allows switching the sensor between "factory mode" and "operation + mode" by writing "1" or "0" to it. In factory mode (1) it is + possible to get the raw data from the sensor. Note that in factory + mode regular events don't get delivered and the options described + above are unavailable. + +raw_data: + contains num_x * num_y big endian 16 bit values describing the raw + values for each sensor field. Note that each read() call on this + files triggers a new readout. It is recommended to provide a buffer + big enough to contain num_x * num_y * 2 bytes. + +Note that reading raw_data gives a I/O error when the device is not in factory +mode. The same happens when reading/writing to the parameter files when the +device is not in regular operation mode. diff --git a/Documentation/input/devices/elantech.rst b/Documentation/input/devices/elantech.rst new file mode 100644 index 000000000..c3374a7ce --- /dev/null +++ b/Documentation/input/devices/elantech.rst @@ -0,0 +1,841 @@ +Elantech Touchpad Driver +======================== + + Copyright (C) 2007-2008 Arjan Opmeer <arjan@opmeer.net> + + Extra information for hardware version 1 found and + provided by Steve Havelka + + Version 2 (EeePC) hardware support based on patches + received from Woody at Xandros and forwarded to me + by user StewieGriffin at the eeeuser.com forum + +.. Contents + + 1. Introduction + 2. Extra knobs + 3. Differentiating hardware versions + 4. Hardware version 1 + 4.1 Registers + 4.2 Native relative mode 4 byte packet format + 4.3 Native absolute mode 4 byte packet format + 5. Hardware version 2 + 5.1 Registers + 5.2 Native absolute mode 6 byte packet format + 5.2.1 Parity checking and packet re-synchronization + 5.2.2 One/Three finger touch + 5.2.3 Two finger touch + 6. Hardware version 3 + 6.1 Registers + 6.2 Native absolute mode 6 byte packet format + 6.2.1 One/Three finger touch + 6.2.2 Two finger touch + 7. Hardware version 4 + 7.1 Registers + 7.2 Native absolute mode 6 byte packet format + 7.2.1 Status packet + 7.2.2 Head packet + 7.2.3 Motion packet + 8. Trackpoint (for Hardware version 3 and 4) + 8.1 Registers + 8.2 Native relative mode 6 byte packet format + 8.2.1 Status Packet + + + +Introduction +~~~~~~~~~~~~ + +Currently the Linux Elantech touchpad driver is aware of four different +hardware versions unimaginatively called version 1,version 2, version 3 +and version 4. Version 1 is found in "older" laptops and uses 4 bytes per +packet. Version 2 seems to be introduced with the EeePC and uses 6 bytes +per packet, and provides additional features such as position of two fingers, +and width of the touch. Hardware version 3 uses 6 bytes per packet (and +for 2 fingers the concatenation of two 6 bytes packets) and allows tracking +of up to 3 fingers. Hardware version 4 uses 6 bytes per packet, and can +combine a status packet with multiple head or motion packets. Hardware version +4 allows tracking up to 5 fingers. + +Some Hardware version 3 and version 4 also have a trackpoint which uses a +separate packet format. It is also 6 bytes per packet. + +The driver tries to support both hardware versions and should be compatible +with the Xorg Synaptics touchpad driver and its graphical configuration +utilities. + +Note that a mouse button is also associated with either the touchpad or the +trackpoint when a trackpoint is available. Disabling the Touchpad in xorg +(TouchPadOff=0) will also disable the buttons associated with the touchpad. + +Additionally the operation of the touchpad can be altered by adjusting the +contents of some of its internal registers. These registers are represented +by the driver as sysfs entries under /sys/bus/serio/drivers/psmouse/serio? +that can be read from and written to. + +Currently only the registers for hardware version 1 are somewhat understood. +Hardware version 2 seems to use some of the same registers but it is not +known whether the bits in the registers represent the same thing or might +have changed their meaning. + +On top of that, some register settings have effect only when the touchpad is +in relative mode and not in absolute mode. As the Linux Elantech touchpad +driver always puts the hardware into absolute mode not all information +mentioned below can be used immediately. But because there is no freely +available Elantech documentation the information is provided here anyway for +completeness sake. + + +Extra knobs +~~~~~~~~~~~ + +Currently the Linux Elantech touchpad driver provides three extra knobs under +/sys/bus/serio/drivers/psmouse/serio? for the user. + +* debug + + Turn different levels of debugging ON or OFF. + + By echoing "0" to this file all debugging will be turned OFF. + + Currently a value of "1" will turn on some basic debugging and a value of + "2" will turn on packet debugging. For hardware version 1 the default is + OFF. For version 2 the default is "1". + + Turning packet debugging on will make the driver dump every packet + received to the syslog before processing it. Be warned that this can + generate quite a lot of data! + +* paritycheck + + Turns parity checking ON or OFF. + + By echoing "0" to this file parity checking will be turned OFF. Any + non-zero value will turn it ON. For hardware version 1 the default is ON. + For version 2 the default it is OFF. + + Hardware version 1 provides basic data integrity verification by + calculating a parity bit for the last 3 bytes of each packet. The driver + can check these bits and reject any packet that appears corrupted. Using + this knob you can bypass that check. + + Hardware version 2 does not provide the same parity bits. Only some basic + data consistency checking can be done. For now checking is disabled by + default. Currently even turning it on will do nothing. + +* crc_enabled + + Sets crc_enabled to 0/1. The name "crc_enabled" is the official name of + this integrity check, even though it is not an actual cyclic redundancy + check. + + Depending on the state of crc_enabled, certain basic data integrity + verification is done by the driver on hardware version 3 and 4. The + driver will reject any packet that appears corrupted. Using this knob, + The state of crc_enabled can be altered with this knob. + + Reading the crc_enabled value will show the active value. Echoing + "0" or "1" to this file will set the state to "0" or "1". + +Differentiating hardware versions +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +To detect the hardware version, read the version number as param[0].param[1].param[2]:: + + 4 bytes version: (after the arrow is the name given in the Dell-provided driver) + 02.00.22 => EF013 + 02.06.00 => EF019 + +In the wild, there appear to be more versions, such as 00.01.64, 01.00.21, +02.00.00, 02.00.04, 02.00.06:: + + 6 bytes: + 02.00.30 => EF113 + 02.08.00 => EF023 + 02.08.XX => EF123 + 02.0B.00 => EF215 + 04.01.XX => Scroll_EF051 + 04.02.XX => EF051 + +In the wild, there appear to be more versions, such as 04.03.01, 04.04.11. There +appears to be almost no difference, except for EF113, which does not report +pressure/width and has different data consistency checks. + +Probably all the versions with param[0] <= 01 can be considered as +4 bytes/firmware 1. The versions < 02.08.00, with the exception of 02.00.30, as +4 bytes/firmware 2. Everything >= 02.08.00 can be considered as 6 bytes. + + +Hardware version 1 +~~~~~~~~~~~~~~~~~~ + +Registers +--------- + +By echoing a hexadecimal value to a register it contents can be altered. + +For example:: + + echo -n 0x16 > reg_10 + +* reg_10:: + + bit 7 6 5 4 3 2 1 0 + B C T D L A S E + + E: 1 = enable smart edges unconditionally + S: 1 = enable smart edges only when dragging + A: 1 = absolute mode (needs 4 byte packets, see reg_11) + L: 1 = enable drag lock (see reg_22) + D: 1 = disable dynamic resolution + T: 1 = disable tapping + C: 1 = enable corner tap + B: 1 = swap left and right button + +* reg_11:: + + bit 7 6 5 4 3 2 1 0 + 1 0 0 H V 1 F P + + P: 1 = enable parity checking for relative mode + F: 1 = enable native 4 byte packet mode + V: 1 = enable vertical scroll area + H: 1 = enable horizontal scroll area + +* reg_20:: + + single finger width? + +* reg_21:: + + scroll area width (small: 0x40 ... wide: 0xff) + +* reg_22:: + + drag lock time out (short: 0x14 ... long: 0xfe; + 0xff = tap again to release) + +* reg_23:: + + tap make timeout? + +* reg_24:: + + tap release timeout? + +* reg_25:: + + smart edge cursor speed (0x02 = slow, 0x03 = medium, 0x04 = fast) + +* reg_26:: + + smart edge activation area width? + + +Native relative mode 4 byte packet format +----------------------------------------- + +byte 0:: + + bit 7 6 5 4 3 2 1 0 + c c p2 p1 1 M R L + + L, R, M = 1 when Left, Right, Middle mouse button pressed + some models have M as byte 3 odd parity bit + when parity checking is enabled (reg_11, P = 1): + p1..p2 = byte 1 and 2 odd parity bit + c = 1 when corner tap detected + +byte 1:: + + bit 7 6 5 4 3 2 1 0 + dx7 dx6 dx5 dx4 dx3 dx2 dx1 dx0 + + dx7..dx0 = x movement; positive = right, negative = left + byte 1 = 0xf0 when corner tap detected + +byte 2:: + + bit 7 6 5 4 3 2 1 0 + dy7 dy6 dy5 dy4 dy3 dy2 dy1 dy0 + + dy7..dy0 = y movement; positive = up, negative = down + +byte 3:: + + parity checking enabled (reg_11, P = 1): + + bit 7 6 5 4 3 2 1 0 + w h n1 n0 ds3 ds2 ds1 ds0 + + normally: + ds3..ds0 = scroll wheel amount and direction + positive = down or left + negative = up or right + when corner tap detected: + ds0 = 1 when top right corner tapped + ds1 = 1 when bottom right corner tapped + ds2 = 1 when bottom left corner tapped + ds3 = 1 when top left corner tapped + n1..n0 = number of fingers on touchpad + only models with firmware 2.x report this, models with + firmware 1.x seem to map one, two and three finger taps + directly to L, M and R mouse buttons + h = 1 when horizontal scroll action + w = 1 when wide finger touch? + + otherwise (reg_11, P = 0): + + bit 7 6 5 4 3 2 1 0 + ds7 ds6 ds5 ds4 ds3 ds2 ds1 ds0 + + ds7..ds0 = vertical scroll amount and direction + negative = up + positive = down + + +Native absolute mode 4 byte packet format +----------------------------------------- + +EF013 and EF019 have a special behaviour (due to a bug in the firmware?), and +when 1 finger is touching, the first 2 position reports must be discarded. +This counting is reset whenever a different number of fingers is reported. + +byte 0:: + + firmware version 1.x: + + bit 7 6 5 4 3 2 1 0 + D U p1 p2 1 p3 R L + + L, R = 1 when Left, Right mouse button pressed + p1..p3 = byte 1..3 odd parity bit + D, U = 1 when rocker switch pressed Up, Down + + firmware version 2.x: + + bit 7 6 5 4 3 2 1 0 + n1 n0 p2 p1 1 p3 R L + + L, R = 1 when Left, Right mouse button pressed + p1..p3 = byte 1..3 odd parity bit + n1..n0 = number of fingers on touchpad + +byte 1:: + + firmware version 1.x: + + bit 7 6 5 4 3 2 1 0 + f 0 th tw x9 x8 y9 y8 + + tw = 1 when two finger touch + th = 1 when three finger touch + f = 1 when finger touch + + firmware version 2.x: + + bit 7 6 5 4 3 2 1 0 + . . . . x9 x8 y9 y8 + +byte 2:: + + bit 7 6 5 4 3 2 1 0 + x7 x6 x5 x4 x3 x2 x1 x0 + + x9..x0 = absolute x value (horizontal) + +byte 3:: + + bit 7 6 5 4 3 2 1 0 + y7 y6 y5 y4 y3 y2 y1 y0 + + y9..y0 = absolute y value (vertical) + + +Hardware version 2 +~~~~~~~~~~~~~~~~~~ + + +Registers +--------- + +By echoing a hexadecimal value to a register it contents can be altered. + +For example:: + + echo -n 0x56 > reg_10 + +* reg_10:: + + bit 7 6 5 4 3 2 1 0 + 0 1 0 1 0 1 D 0 + + D: 1 = enable drag and drop + +* reg_11:: + + bit 7 6 5 4 3 2 1 0 + 1 0 0 0 S 0 1 0 + + S: 1 = enable vertical scroll + +* reg_21:: + + unknown (0x00) + +* reg_22:: + + drag and drop release time out (short: 0x70 ... long 0x7e; + 0x7f = never i.e. tap again to release) + + +Native absolute mode 6 byte packet format +----------------------------------------- + +Parity checking and packet re-synchronization +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +There is no parity checking, however some consistency checks can be performed. + +For instance for EF113:: + + SA1= packet[0]; + A1 = packet[1]; + B1 = packet[2]; + SB1= packet[3]; + C1 = packet[4]; + D1 = packet[5]; + if( (((SA1 & 0x3C) != 0x3C) && ((SA1 & 0xC0) != 0x80)) || // check Byte 1 + (((SA1 & 0x0C) != 0x0C) && ((SA1 & 0xC0) == 0x80)) || // check Byte 1 (one finger pressed) + (((SA1 & 0xC0) != 0x80) && (( A1 & 0xF0) != 0x00)) || // check Byte 2 + (((SB1 & 0x3E) != 0x38) && ((SA1 & 0xC0) != 0x80)) || // check Byte 4 + (((SB1 & 0x0E) != 0x08) && ((SA1 & 0xC0) == 0x80)) || // check Byte 4 (one finger pressed) + (((SA1 & 0xC0) != 0x80) && (( C1 & 0xF0) != 0x00)) ) // check Byte 5 + // error detected + +For all the other ones, there are just a few constant bits:: + + if( ((packet[0] & 0x0C) != 0x04) || + ((packet[3] & 0x0f) != 0x02) ) + // error detected + + +In case an error is detected, all the packets are shifted by one (and packet[0] is discarded). + +One/Three finger touch +^^^^^^^^^^^^^^^^^^^^^^ + +byte 0:: + + bit 7 6 5 4 3 2 1 0 + n1 n0 w3 w2 . . R L + + L, R = 1 when Left, Right mouse button pressed + n1..n0 = number of fingers on touchpad + +byte 1:: + + bit 7 6 5 4 3 2 1 0 + p7 p6 p5 p4 x11 x10 x9 x8 + +byte 2:: + + bit 7 6 5 4 3 2 1 0 + x7 x6 x5 x4 x3 x2 x1 x0 + + x11..x0 = absolute x value (horizontal) + +byte 3:: + + bit 7 6 5 4 3 2 1 0 + n4 vf w1 w0 . . . b2 + + n4 = set if more than 3 fingers (only in 3 fingers mode) + vf = a kind of flag ? (only on EF123, 0 when finger is over one + of the buttons, 1 otherwise) + w3..w0 = width of the finger touch (not EF113) + b2 (on EF113 only, 0 otherwise), b2.R.L indicates one button pressed: + 0 = none + 1 = Left + 2 = Right + 3 = Middle (Left and Right) + 4 = Forward + 5 = Back + 6 = Another one + 7 = Another one + +byte 4:: + + bit 7 6 5 4 3 2 1 0 + p3 p1 p2 p0 y11 y10 y9 y8 + + p7..p0 = pressure (not EF113) + +byte 5:: + + bit 7 6 5 4 3 2 1 0 + y7 y6 y5 y4 y3 y2 y1 y0 + + y11..y0 = absolute y value (vertical) + + +Two finger touch +^^^^^^^^^^^^^^^^ + +Note that the two pairs of coordinates are not exactly the coordinates of the +two fingers, but only the pair of the lower-left and upper-right coordinates. +So the actual fingers might be situated on the other diagonal of the square +defined by these two points. + +byte 0:: + + bit 7 6 5 4 3 2 1 0 + n1 n0 ay8 ax8 . . R L + + L, R = 1 when Left, Right mouse button pressed + n1..n0 = number of fingers on touchpad + +byte 1:: + + bit 7 6 5 4 3 2 1 0 + ax7 ax6 ax5 ax4 ax3 ax2 ax1 ax0 + + ax8..ax0 = lower-left finger absolute x value + +byte 2:: + + bit 7 6 5 4 3 2 1 0 + ay7 ay6 ay5 ay4 ay3 ay2 ay1 ay0 + + ay8..ay0 = lower-left finger absolute y value + +byte 3:: + + bit 7 6 5 4 3 2 1 0 + . . by8 bx8 . . . . + +byte 4:: + + bit 7 6 5 4 3 2 1 0 + bx7 bx6 bx5 bx4 bx3 bx2 bx1 bx0 + + bx8..bx0 = upper-right finger absolute x value + +byte 5:: + + bit 7 6 5 4 3 2 1 0 + by7 by8 by5 by4 by3 by2 by1 by0 + + by8..by0 = upper-right finger absolute y value + +Hardware version 3 +~~~~~~~~~~~~~~~~~~ + +Registers +--------- + +* reg_10:: + + bit 7 6 5 4 3 2 1 0 + 0 0 0 0 R F T A + + A: 1 = enable absolute tracking + T: 1 = enable two finger mode auto correct + F: 1 = disable ABS Position Filter + R: 1 = enable real hardware resolution + +Native absolute mode 6 byte packet format +----------------------------------------- + +1 and 3 finger touch shares the same 6-byte packet format, except that +3 finger touch only reports the position of the center of all three fingers. + +Firmware would send 12 bytes of data for 2 finger touch. + +Note on debounce: +In case the box has unstable power supply or other electricity issues, or +when number of finger changes, F/W would send "debounce packet" to inform +driver that the hardware is in debounce status. +The debouce packet has the following signature:: + + byte 0: 0xc4 + byte 1: 0xff + byte 2: 0xff + byte 3: 0x02 + byte 4: 0xff + byte 5: 0xff + +When we encounter this kind of packet, we just ignore it. + +One/Three finger touch +^^^^^^^^^^^^^^^^^^^^^^ + +byte 0:: + + bit 7 6 5 4 3 2 1 0 + n1 n0 w3 w2 0 1 R L + + L, R = 1 when Left, Right mouse button pressed + n1..n0 = number of fingers on touchpad + +byte 1:: + + bit 7 6 5 4 3 2 1 0 + p7 p6 p5 p4 x11 x10 x9 x8 + +byte 2:: + + bit 7 6 5 4 3 2 1 0 + x7 x6 x5 x4 x3 x2 x1 x0 + + x11..x0 = absolute x value (horizontal) + +byte 3:: + + bit 7 6 5 4 3 2 1 0 + 0 0 w1 w0 0 0 1 0 + + w3..w0 = width of the finger touch + +byte 4:: + + bit 7 6 5 4 3 2 1 0 + p3 p1 p2 p0 y11 y10 y9 y8 + + p7..p0 = pressure + +byte 5:: + + bit 7 6 5 4 3 2 1 0 + y7 y6 y5 y4 y3 y2 y1 y0 + + y11..y0 = absolute y value (vertical) + +Two finger touch +^^^^^^^^^^^^^^^^ + +The packet format is exactly the same for two finger touch, except the hardware +sends two 6 byte packets. The first packet contains data for the first finger, +the second packet has data for the second finger. So for two finger touch a +total of 12 bytes are sent. + +Hardware version 4 +~~~~~~~~~~~~~~~~~~ + +Registers +--------- + +* reg_07:: + + bit 7 6 5 4 3 2 1 0 + 0 0 0 0 0 0 0 A + + A: 1 = enable absolute tracking + +Native absolute mode 6 byte packet format +----------------------------------------- + +v4 hardware is a true multitouch touchpad, capable of tracking up to 5 fingers. +Unfortunately, due to PS/2's limited bandwidth, its packet format is rather +complex. + +Whenever the numbers or identities of the fingers changes, the hardware sends a +status packet to indicate how many and which fingers is on touchpad, followed by +head packets or motion packets. A head packet contains data of finger id, finger +position (absolute x, y values), width, and pressure. A motion packet contains +two fingers' position delta. + +For example, when status packet tells there are 2 fingers on touchpad, then we +can expect two following head packets. If the finger status doesn't change, +the following packets would be motion packets, only sending delta of finger +position, until we receive a status packet. + +One exception is one finger touch. when a status packet tells us there is only +one finger, the hardware would just send head packets afterwards. + +Status packet +^^^^^^^^^^^^^ + +byte 0:: + + bit 7 6 5 4 3 2 1 0 + . . . . 0 1 R L + + L, R = 1 when Left, Right mouse button pressed + +byte 1:: + + bit 7 6 5 4 3 2 1 0 + . . . ft4 ft3 ft2 ft1 ft0 + + ft4 ft3 ft2 ft1 ft0 ftn = 1 when finger n is on touchpad + +byte 2:: + + not used + +byte 3:: + + bit 7 6 5 4 3 2 1 0 + . . . 1 0 0 0 0 + + constant bits + +byte 4:: + + bit 7 6 5 4 3 2 1 0 + p . . . . . . . + + p = 1 for palm + +byte 5:: + + not used + +Head packet +^^^^^^^^^^^ + +byte 0:: + + bit 7 6 5 4 3 2 1 0 + w3 w2 w1 w0 0 1 R L + + L, R = 1 when Left, Right mouse button pressed + w3..w0 = finger width (spans how many trace lines) + +byte 1:: + + bit 7 6 5 4 3 2 1 0 + p7 p6 p5 p4 x11 x10 x9 x8 + +byte 2:: + + bit 7 6 5 4 3 2 1 0 + x7 x6 x5 x4 x3 x2 x1 x0 + + x11..x0 = absolute x value (horizontal) + +byte 3:: + + bit 7 6 5 4 3 2 1 0 + id2 id1 id0 1 0 0 0 1 + + id2..id0 = finger id + +byte 4:: + + bit 7 6 5 4 3 2 1 0 + p3 p1 p2 p0 y11 y10 y9 y8 + + p7..p0 = pressure + +byte 5:: + + bit 7 6 5 4 3 2 1 0 + y7 y6 y5 y4 y3 y2 y1 y0 + + y11..y0 = absolute y value (vertical) + +Motion packet +^^^^^^^^^^^^^ + +byte 0:: + + bit 7 6 5 4 3 2 1 0 + id2 id1 id0 w 0 1 R L + + L, R = 1 when Left, Right mouse button pressed + id2..id0 = finger id + w = 1 when delta overflows (> 127 or < -128), in this case + firmware sends us (delta x / 5) and (delta y / 5) + +byte 1:: + + bit 7 6 5 4 3 2 1 0 + x7 x6 x5 x4 x3 x2 x1 x0 + + x7..x0 = delta x (two's complement) + +byte 2:: + + bit 7 6 5 4 3 2 1 0 + y7 y6 y5 y4 y3 y2 y1 y0 + + y7..y0 = delta y (two's complement) + +byte 3:: + + bit 7 6 5 4 3 2 1 0 + id2 id1 id0 1 0 0 1 0 + + id2..id0 = finger id + +byte 4:: + + bit 7 6 5 4 3 2 1 0 + x7 x6 x5 x4 x3 x2 x1 x0 + + x7..x0 = delta x (two's complement) + +byte 5:: + + bit 7 6 5 4 3 2 1 0 + y7 y6 y5 y4 y3 y2 y1 y0 + + y7..y0 = delta y (two's complement) + + byte 0 ~ 2 for one finger + byte 3 ~ 5 for another + + +Trackpoint (for Hardware version 3 and 4) +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +Registers +--------- + +No special registers have been identified. + +Native relative mode 6 byte packet format +----------------------------------------- + +Status Packet +^^^^^^^^^^^^^ + +byte 0:: + + bit 7 6 5 4 3 2 1 0 + 0 0 sx sy 0 M R L + +byte 1:: + + bit 7 6 5 4 3 2 1 0 + ~sx 0 0 0 0 0 0 0 + +byte 2:: + + bit 7 6 5 4 3 2 1 0 + ~sy 0 0 0 0 0 0 0 + +byte 3:: + + bit 7 6 5 4 3 2 1 0 + 0 0 ~sy ~sx 0 1 1 0 + +byte 4:: + + bit 7 6 5 4 3 2 1 0 + x7 x6 x5 x4 x3 x2 x1 x0 + +byte 5:: + + bit 7 6 5 4 3 2 1 0 + y7 y6 y5 y4 y3 y2 y1 y0 + + + x and y are written in two's complement spread + over 9 bits with sx/sy the relative top bit and + x7..x0 and y7..y0 the lower bits. + ~sx is the inverse of sx, ~sy is the inverse of sy. + The sign of y is opposite to what the input driver + expects for a relative movement diff --git a/Documentation/input/devices/iforce-protocol.rst b/Documentation/input/devices/iforce-protocol.rst new file mode 100644 index 000000000..8634beac3 --- /dev/null +++ b/Documentation/input/devices/iforce-protocol.rst @@ -0,0 +1,381 @@ +=============== +Iforce Protocol +=============== + +:Author: Johann Deneux <johann.deneux@gmail.com> + +Home page at `<http://web.archive.org/web/*/http://www.esil.univ-mrs.fr>`_ + +:Additions: by Vojtech Pavlik. + + +Introduction +============ + +This document describes what I managed to discover about the protocol used to +specify force effects to I-Force 2.0 devices. None of this information comes +from Immerse. That's why you should not trust what is written in this +document. This document is intended to help understanding the protocol. +This is not a reference. Comments and corrections are welcome. To contact me, +send an email to: johann.deneux@gmail.com + +.. warning:: + + I shall not be held responsible for any damage or harm caused if you try to + send data to your I-Force device based on what you read in this document. + +Preliminary Notes +================= + +All values are hexadecimal with big-endian encoding (msb on the left). Beware, +values inside packets are encoded using little-endian. Bytes whose roles are +unknown are marked ??? Information that needs deeper inspection is marked (?) + +General form of a packet +------------------------ + +This is how packets look when the device uses the rs232 to communicate. + +== == === ==== == +2B OP LEN DATA CS +== == === ==== == + +CS is the checksum. It is equal to the exclusive or of all bytes. + +When using USB: + +== ==== +OP DATA +== ==== + +The 2B, LEN and CS fields have disappeared, probably because USB handles +frames and data corruption is handled or unsignificant. + +First, I describe effects that are sent by the device to the computer + +Device input state +================== + +This packet is used to indicate the state of each button and the value of each +axis:: + + OP= 01 for a joystick, 03 for a wheel + LEN= Varies from device to device + 00 X-Axis lsb + 01 X-Axis msb + 02 Y-Axis lsb, or gas pedal for a wheel + 03 Y-Axis msb, or brake pedal for a wheel + 04 Throttle + 05 Buttons + 06 Lower 4 bits: Buttons + Upper 4 bits: Hat + 07 Rudder + +Device effects states +===================== + +:: + + OP= 02 + LEN= Varies + 00 ? Bit 1 (Value 2) is the value of the deadman switch + 01 Bit 8 is set if the effect is playing. Bits 0 to 7 are the effect id. + 02 ?? + 03 Address of parameter block changed (lsb) + 04 Address of parameter block changed (msb) + 05 Address of second parameter block changed (lsb) + ... depending on the number of parameter blocks updated + +Force effect +------------ + +:: + + OP= 01 + LEN= 0e + 00 Channel (when playing several effects at the same time, each must + be assigned a channel) + 01 Wave form + Val 00 Constant + Val 20 Square + Val 21 Triangle + Val 22 Sine + Val 23 Sawtooth up + Val 24 Sawtooth down + Val 40 Spring (Force = f(pos)) + Val 41 Friction (Force = f(velocity)) and Inertia + (Force = f(acceleration)) + + + 02 Axes affected and trigger + Bits 4-7: Val 2 = effect along one axis. Byte 05 indicates direction + Val 4 = X axis only. Byte 05 must contain 5a + Val 8 = Y axis only. Byte 05 must contain b4 + Val c = X and Y axes. Bytes 05 must contain 60 + Bits 0-3: Val 0 = No trigger + Val x+1 = Button x triggers the effect + When the whole byte is 0, cancel the previously set trigger + + 03-04 Duration of effect (little endian encoding, in ms) + + 05 Direction of effect, if applicable. Else, see 02 for value to assign. + + 06-07 Minimum time between triggering. + + 08-09 Address of periodicity or magnitude parameters + 0a-0b Address of attack and fade parameters, or ffff if none. + *or* + 08-09 Address of interactive parameters for X-axis, + or ffff if not applicable + 0a-0b Address of interactive parameters for Y-axis, + or ffff if not applicable + + 0c-0d Delay before execution of effect (little endian encoding, in ms) + + +Time based parameters +--------------------- + +Attack and fade +^^^^^^^^^^^^^^^ + +:: + + OP= 02 + LEN= 08 + 00-01 Address where to store the parameters + 02-03 Duration of attack (little endian encoding, in ms) + 04 Level at end of attack. Signed byte. + 05-06 Duration of fade. + 07 Level at end of fade. + +Magnitude +^^^^^^^^^ + +:: + + OP= 03 + LEN= 03 + 00-01 Address + 02 Level. Signed byte. + +Periodicity +^^^^^^^^^^^ + +:: + + OP= 04 + LEN= 07 + 00-01 Address + 02 Magnitude. Signed byte. + 03 Offset. Signed byte. + 04 Phase. Val 00 = 0 deg, Val 40 = 90 degs. + 05-06 Period (little endian encoding, in ms) + +Interactive parameters +---------------------- + +:: + + OP= 05 + LEN= 0a + 00-01 Address + 02 Positive Coeff + 03 Negative Coeff + 04+05 Offset (center) + 06+07 Dead band (Val 01F4 = 5000 (decimal)) + 08 Positive saturation (Val 0a = 1000 (decimal) Val 64 = 10000 (decimal)) + 09 Negative saturation + +The encoding is a bit funny here: For coeffs, these are signed values. The +maximum value is 64 (100 decimal), the min is 9c. +For the offset, the minimum value is FE0C, the maximum value is 01F4. +For the deadband, the minimum value is 0, the max is 03E8. + +Controls +-------- + +:: + + OP= 41 + LEN= 03 + 00 Channel + 01 Start/Stop + Val 00: Stop + Val 01: Start and play once. + Val 41: Start and play n times (See byte 02 below) + 02 Number of iterations n. + +Init +---- + + +Querying features +^^^^^^^^^^^^^^^^^ +:: + + OP= ff + Query command. Length varies according to the query type. + The general format of this packet is: + ff 01 QUERY [INDEX] CHECKSUM + responses are of the same form: + FF LEN QUERY VALUE_QUERIED CHECKSUM2 + where LEN = 1 + length(VALUE_QUERIED) + +Query ram size +~~~~~~~~~~~~~~ + +:: + + QUERY = 42 ('B'uffer size) + +The device should reply with the same packet plus two additional bytes +containing the size of the memory: +ff 03 42 03 e8 CS would mean that the device has 1000 bytes of ram available. + +Query number of effects +~~~~~~~~~~~~~~~~~~~~~~~ + +:: + + QUERY = 4e ('N'umber of effects) + +The device should respond by sending the number of effects that can be played +at the same time (one byte) +ff 02 4e 14 CS would stand for 20 effects. + +Vendor's id +~~~~~~~~~~~ + +:: + + QUERY = 4d ('M'anufacturer) + +Query the vendors'id (2 bytes) + +Product id +~~~~~~~~~~ + +:: + + QUERY = 50 ('P'roduct) + +Query the product id (2 bytes) + +Open device +~~~~~~~~~~~ + +:: + + QUERY = 4f ('O'pen) + +No data returned. + +Close device +~~~~~~~~~~~~ + +:: + + QUERY = 43 ('C')lose + +No data returned. + +Query effect +~~~~~~~~~~~~ + +:: + + QUERY = 45 ('E') + +Send effect type. +Returns nonzero if supported (2 bytes) + +Firmware Version +~~~~~~~~~~~~~~~~ + +:: + + QUERY = 56 ('V'ersion) + +Sends back 3 bytes - major, minor, subminor + +Initialisation of the device +^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +Set Control +~~~~~~~~~~~ + +.. note:: + Device dependent, can be different on different models! + +:: + + OP= 40 <idx> <val> [<val>] + LEN= 2 or 3 + 00 Idx + Idx 00 Set dead zone (0..2048) + Idx 01 Ignore Deadman sensor (0..1) + Idx 02 Enable comm watchdog (0..1) + Idx 03 Set the strength of the spring (0..100) + Idx 04 Enable or disable the spring (0/1) + Idx 05 Set axis saturation threshold (0..2048) + +Set Effect State +~~~~~~~~~~~~~~~~ + +:: + + OP= 42 <val> + LEN= 1 + 00 State + Bit 3 Pause force feedback + Bit 2 Enable force feedback + Bit 0 Stop all effects + +Set overall +~~~~~~~~~~~ + +:: + + OP= 43 <val> + LEN= 1 + 00 Gain + Val 00 = 0% + Val 40 = 50% + Val 80 = 100% + +Parameter memory +---------------- + +Each device has a certain amount of memory to store parameters of effects. +The amount of RAM may vary, I encountered values from 200 to 1000 bytes. Below +is the amount of memory apparently needed for every set of parameters: + + - period : 0c + - magnitude : 02 + - attack and fade : 0e + - interactive : 08 + +Appendix: How to study the protocol? +==================================== + +1. Generate effects using the force editor provided with the DirectX SDK, or +use Immersion Studio (freely available at their web site in the developer section: +www.immersion.com) +2. Start a soft spying RS232 or USB (depending on where you connected your +joystick/wheel). I used ComPortSpy from fCoder (alpha version!) +3. Play the effect, and watch what happens on the spy screen. + +A few words about ComPortSpy: +At first glance, this software seems, hum, well... buggy. In fact, data appear with a +few seconds latency. Personally, I restart it every time I play an effect. +Remember it's free (as in free beer) and alpha! + +URLS +==== + +Check http://www.immerse.com for Immersion Studio, +and http://www.fcoder.com for ComPortSpy. + + +I-Force is trademark of Immersion Corp. diff --git a/Documentation/input/devices/index.rst b/Documentation/input/devices/index.rst new file mode 100644 index 000000000..95a453782 --- /dev/null +++ b/Documentation/input/devices/index.rst @@ -0,0 +1,19 @@ +Driver-specific documentation +============================= + +This section provides information about various devices supported by the +Linux kernel, their protocols, and driver details. + +.. toctree:: + :maxdepth: 2 + :numbered: + :glob: + + * + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/input/devices/joystick-parport.rst b/Documentation/input/devices/joystick-parport.rst new file mode 100644 index 000000000..e8ce16ee7 --- /dev/null +++ b/Documentation/input/devices/joystick-parport.rst @@ -0,0 +1,611 @@ +.. include:: <isonum.txt> + +.. _joystick-parport: + +============================== +Parallel Port Joystick Drivers +============================== + +:Copyright: |copy| 1998-2000 Vojtech Pavlik <vojtech@ucw.cz> +:Copyright: |copy| 1998 Andree Borrmann <a.borrmann@tu-bs.de> + + +Sponsored by SuSE + +Disclaimer +========== + +Any information in this file is provided as-is, without any guarantee that +it will be true. So, use it at your own risk. The possible damages that can +happen include burning your parallel port, and/or the sticks and joystick +and maybe even more. Like when a lightning kills you it is not our problem. + +Introduction +============ + +The joystick parport drivers are used for joysticks and gamepads not +originally designed for PCs and other computers Linux runs on. Because of +that, PCs usually lack the right ports to connect these devices to. Parallel +port, because of its ability to change single bits at will, and providing +both output and input bits is the most suitable port on the PC for +connecting such devices. + +Devices supported +================= + +Many console and 8-bit computer gamepads and joysticks are supported. The +following subsections discuss usage of each. + +NES and SNES +------------ + +The Nintendo Entertainment System and Super Nintendo Entertainment System +gamepads are widely available, and easy to get. Also, they are quite easy to +connect to a PC, and don't need much processing speed (108 us for NES and +165 us for SNES, compared to about 1000 us for PC gamepads) to communicate +with them. + +All NES and SNES use the same synchronous serial protocol, clocked from +the computer's side (and thus timing insensitive). To allow up to 5 NES +and/or SNES gamepads and/or SNES mice connected to the parallel port at once, +the output lines of the parallel port are shared, while one of 5 available +input lines is assigned to each gamepad. + +This protocol is handled by the gamecon.c driver, so that's the one +you'll use for NES, SNES gamepads and SNES mice. + +The main problem with PC parallel ports is that they don't have +5V power +source on any of their pins. So, if you want a reliable source of power +for your pads, use either keyboard or joystick port, and make a pass-through +cable. You can also pull the power directly from the power supply (the red +wire is +5V). + +If you want to use the parallel port only, you can take the power is from +some data pin. For most gamepad and parport implementations only one pin is +needed, and I'd recommend pin 9 for that, the highest data bit. On the other +hand, if you are not planning to use anything else than NES / SNES on the +port, anything between and including pin 4 and pin 9 will work:: + + (pin 9) -----> Power + +Unfortunately, there are pads that need a lot more of power, and parallel +ports that can't give much current through the data pins. If this is your +case, you'll need to use diodes (as a prevention of destroying your parallel +port), and combine the currents of two or more data bits together:: + + Diodes + (pin 9) ----|>|-------+------> Power + | + (pin 8) ----|>|-------+ + | + (pin 7) ----|>|-------+ + | + <and so on> : + | + (pin 4) ----|>|-------+ + +Ground is quite easy. On PC's parallel port the ground is on any of the +pins from pin 18 to pin 25. So use any pin of these you like for the ground:: + + (pin 18) -----> Ground + +NES and SNES pads have two input bits, Clock and Latch, which drive the +serial transfer. These are connected to pins 2 and 3 of the parallel port, +respectively:: + + (pin 2) -----> Clock + (pin 3) -----> Latch + +And the last thing is the NES / SNES data wire. Only that isn't shared and +each pad needs its own data pin. The parallel port pins are:: + + (pin 10) -----> Pad 1 data + (pin 11) -----> Pad 2 data + (pin 12) -----> Pad 3 data + (pin 13) -----> Pad 4 data + (pin 15) -----> Pad 5 data + +Note that pin 14 is not used, since it is not an input pin on the parallel +port. + +This is everything you need on the PC's side of the connection, now on to +the gamepads side. The NES and SNES have different connectors. Also, there +are quite a lot of NES clones, and because Nintendo used proprietary +connectors for their machines, the cloners couldn't and used standard D-Cannon +connectors. Anyway, if you've got a gamepad, and it has buttons A, B, Turbo +A, Turbo B, Select and Start, and is connected through 5 wires, then it is +either a NES or NES clone and will work with this connection. SNES gamepads +also use 5 wires, but have more buttons. They will work as well, of course:: + + Pinout for NES gamepads Pinout for SNES gamepads and mice + + +----> Power +-----------------------\ + | 7 | o o o o | x x o | 1 + 5 +---------+ 7 +-----------------------/ + | x x o \ | | | | | + | o o o o | | | | | +-> Ground + 4 +------------+ 1 | | | +------------> Data + | | | | | | +---------------> Latch + | | | +-> Ground | +------------------> Clock + | | +----> Clock +---------------------> Power + | +-------> Latch + +----------> Data + + Pinout for NES clone (db9) gamepads Pinout for NES clone (db15) gamepads + + +---------> Clock +-----------------> Data + | +-------> Latch | +---> Ground + | | +-----> Data | | + | | | ___________________ + _____________ 8 \ o x x x x x x o / 1 + 5 \ x o o o x / 1 \ o x x o x x o / + \ x o x o / 15 `~~~~~~~~~~~~~' 9 + 9 `~~~~~~~' 6 | | | + | | | | +----> Clock + | +----> Power | +----------> Latch + +--------> Ground +----------------> Power + +Multisystem joysticks +--------------------- + +In the era of 8-bit machines, there was something like de-facto standard +for joystick ports. They were all digital, and all used D-Cannon 9 pin +connectors (db9). Because of that, a single joystick could be used without +hassle on Atari (130, 800XE, 800XL, 2600, 7200), Amiga, Commodore C64, +Amstrad CPC, Sinclair ZX Spectrum and many other machines. That's why these +joysticks are called "Multisystem". + +Now their pinout:: + + +---------> Right + | +-------> Left + | | +-----> Down + | | | +---> Up + | | | | + _____________ + 5 \ x o o o o / 1 + \ x o x o / + 9 `~~~~~~~' 6 + | | + | +----> Button + +--------> Ground + +However, as time passed, extensions to this standard developed, and these +were not compatible with each other:: + + + Atari 130, 800/XL/XE MSX + + +-----------> Power + +---------> Right | +---------> Right + | +-------> Left | | +-------> Left + | | +-----> Down | | | +-----> Down + | | | +---> Up | | | | +---> Up + | | | | | | | | | + _____________ _____________ + 5 \ x o o o o / 1 5 \ o o o o o / 1 + \ x o o o / \ o o o o / + 9 `~~~~~~~' 6 9 `~~~~~~~' 6 + | | | | | | | + | | +----> Button | | | +----> Button 1 + | +------> Power | | +------> Button 2 + +--------> Ground | +--------> Output 3 + +----------> Ground + + Amstrad CPC Commodore C64 + + +-----------> Analog Y + +---------> Right | +---------> Right + | +-------> Left | | +-------> Left + | | +-----> Down | | | +-----> Down + | | | +---> Up | | | | +---> Up + | | | | | | | | | + _____________ _____________ + 5 \ x o o o o / 1 5 \ o o o o o / 1 + \ x o o o / \ o o o o / + 9 `~~~~~~~' 6 9 `~~~~~~~' 6 + | | | | | | | + | | +----> Button 1 | | | +----> Button + | +------> Button 2 | | +------> Power + +--------> Ground | +--------> Ground + +----------> Analog X + + Sinclair Spectrum +2A/+3 Amiga 1200 + + +-----------> Up +-----------> Button 3 + | +---------> Fire | +---------> Right + | | | | +-------> Left + | | +-----> Ground | | | +-----> Down + | | | | | | | +---> Up + | | | | | | | | + _____________ _____________ + 5 \ o o x o x / 1 5 \ o o o o o / 1 + \ o o o o / \ o o o o / + 9 `~~~~~~~' 6 9 `~~~~~~~' 6 + | | | | | | | | + | | | +----> Right | | | +----> Button 1 + | | +------> Left | | +------> Power + | +--------> Ground | +--------> Ground + +----------> Down +----------> Button 2 + + And there were many others. + +Multisystem joysticks using db9.c +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +For the Multisystem joysticks, and their derivatives, the db9.c driver +was written. It allows only one joystick / gamepad per parallel port, but +the interface is easy to build and works with almost anything. + +For the basic 1-button Multisystem joystick you connect its wires to the +parallel port like this:: + + (pin 1) -----> Power + (pin 18) -----> Ground + + (pin 2) -----> Up + (pin 3) -----> Down + (pin 4) -----> Left + (pin 5) -----> Right + (pin 6) -----> Button 1 + +However, if the joystick is switch based (eg. clicks when you move it), +you might or might not, depending on your parallel port, need 10 kOhm pullup +resistors on each of the direction and button signals, like this:: + + (pin 2) ------------+------> Up + Resistor | + (pin 1) --[10kOhm]--+ + +Try without, and if it doesn't work, add them. For TTL based joysticks / +gamepads the pullups are not needed. + +For joysticks with two buttons you connect the second button to pin 7 on +the parallel port:: + + (pin 7) -----> Button 2 + +And that's it. + +On a side note, if you have already built a different adapter for use with +the digital joystick driver 0.8.0.2, this is also supported by the db9.c +driver, as device type 8. (See section 3.2) + +Multisystem joysticks using gamecon.c +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +For some people just one joystick per parallel port is not enough, and/or +want to use them on one parallel port together with NES/SNES/PSX pads. This is +possible using the gamecon.c. It supports up to 5 devices of the above types, +including 1 and 2 buttons Multisystem joysticks. + +However, there is nothing for free. To allow more sticks to be used at +once, you need the sticks to be purely switch based (that is non-TTL), and +not to need power. Just a plain simple six switches inside. If your +joystick can do more (eg. turbofire) you'll need to disable it totally first +if you want to use gamecon.c. + +Also, the connection is a bit more complex. You'll need a bunch of diodes, +and one pullup resistor. First, you connect the Directions and the button +the same as for db9, however with the diodes between:: + + Diodes + (pin 2) -----|<|----> Up + (pin 3) -----|<|----> Down + (pin 4) -----|<|----> Left + (pin 5) -----|<|----> Right + (pin 6) -----|<|----> Button 1 + +For two button sticks you also connect the other button:: + + (pin 7) -----|<|----> Button 2 + +And finally, you connect the Ground wire of the joystick, like done in +this little schematic to Power and Data on the parallel port, as described +for the NES / SNES pads in section 2.1 of this file - that is, one data pin +for each joystick. The power source is shared:: + + Data ------------+-----> Ground + Resistor | + Power --[10kOhm]--+ + +And that's all, here we go! + +Multisystem joysticks using turbografx.c +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +The TurboGraFX interface, designed by + + Steffen Schwenke <schwenke@burg-halle.de> + +allows up to 7 Multisystem joysticks connected to the parallel port. In +Steffen's version, there is support for up to 5 buttons per joystick. However, +since this doesn't work reliably on all parallel ports, the turbografx.c driver +supports only one button per joystick. For more information on how to build the +interface, see: + + http://www2.burg-halle.de/~schwenke/parport.html + +Sony Playstation +---------------- + +The PSX controller is supported by the gamecon.c. Pinout of the PSX +controller (compatible with DirectPadPro):: + + +---------+---------+---------+ + 9 | o o o | o o o | o o o | 1 parallel + \________|_________|________/ port pins + | | | | | | + | | | | | +--------> Clock --- (4) + | | | | +------------> Select --- (3) + | | | +---------------> Power --- (5-9) + | | +------------------> Ground --- (18-25) + | +-------------------------> Command --- (2) + +----------------------------> Data --- (one of 10,11,12,13,15) + +The driver supports these controllers: + + * Standard PSX Pad + * NegCon PSX Pad + * Analog PSX Pad (red mode) + * Analog PSX Pad (green mode) + * PSX Rumble Pad + * PSX DDR Pad + +Sega +---- + +All the Sega controllers are more or less based on the standard 2-button +Multisystem joystick. However, since they don't use switches and use TTL +logic, the only driver usable with them is the db9.c driver. + +Sega Master System +~~~~~~~~~~~~~~~~~~ + +The SMS gamepads are almost exactly the same as normal 2-button +Multisystem joysticks. Set the driver to Multi2 mode, use the corresponding +parallel port pins, and the following schematic:: + + +-----------> Power + | +---------> Right + | | +-------> Left + | | | +-----> Down + | | | | +---> Up + | | | | | + _____________ + 5 \ o o o o o / 1 + \ o o x o / + 9 `~~~~~~~' 6 + | | | + | | +----> Button 1 + | +--------> Ground + +----------> Button 2 + +Sega Genesis aka MegaDrive +~~~~~~~~~~~~~~~~~~~~~~~~~~ + +The Sega Genesis (in Europe sold as Sega MegaDrive) pads are an extension +to the Sega Master System pads. They use more buttons (3+1, 5+1, 6+1). Use +the following schematic:: + + +-----------> Power + | +---------> Right + | | +-------> Left + | | | +-----> Down + | | | | +---> Up + | | | | | + _____________ + 5 \ o o o o o / 1 + \ o o o o / + 9 `~~~~~~~' 6 + | | | | + | | | +----> Button 1 + | | +------> Select + | +--------> Ground + +----------> Button 2 + +The Select pin goes to pin 14 on the parallel port:: + + (pin 14) -----> Select + +The rest is the same as for Multi2 joysticks using db9.c + +Sega Saturn +~~~~~~~~~~~ + +Sega Saturn has eight buttons, and to transfer that, without hacks like +Genesis 6 pads use, it needs one more select pin. Anyway, it is still +handled by the db9.c driver. Its pinout is very different from anything +else. Use this schematic:: + + +-----------> Select 1 + | +---------> Power + | | +-------> Up + | | | +-----> Down + | | | | +---> Ground + | | | | | + _____________ + 5 \ o o o o o / 1 + \ o o o o / + 9 `~~~~~~~' 6 + | | | | + | | | +----> Select 2 + | | +------> Right + | +--------> Left + +----------> Power + +Select 1 is pin 14 on the parallel port, Select 2 is pin 16 on the +parallel port:: + + (pin 14) -----> Select 1 + (pin 16) -----> Select 2 + +The other pins (Up, Down, Right, Left, Power, Ground) are the same as for +Multi joysticks using db9.c + +Amiga CD32 +---------- + +Amiga CD32 joypad uses the following pinout:: + + +-----------> Button 3 + | +---------> Right + | | +-------> Left + | | | +-----> Down + | | | | +---> Up + | | | | | + _____________ + 5 \ o o o o o / 1 + \ o o o o / + 9 `~~~~~~~' 6 + | | | | + | | | +----> Button 1 + | | +------> Power + | +--------> Ground + +----------> Button 2 + +It can be connected to the parallel port and driven by db9.c driver. It needs the following wiring: + + ============ ============= + CD32 pad Parallel port + ============ ============= + 1 (Up) 2 (D0) + 2 (Down) 3 (D1) + 3 (Left) 4 (D2) + 4 (Right) 5 (D3) + 5 (Button 3) 14 (AUTOFD) + 6 (Button 1) 17 (SELIN) + 7 (+5V) 1 (STROBE) + 8 (Gnd) 18 (Gnd) + 9 (Button 2) 7 (D5) + ============ ============= + +The drivers +=========== + +There are three drivers for the parallel port interfaces. Each, as +described above, allows to connect a different group of joysticks and pads. +Here are described their command lines: + +gamecon.c +--------- + +Using gamecon.c you can connect up to five devices to one parallel port. It +uses the following kernel/module command line:: + + gamecon.map=port,pad1,pad2,pad3,pad4,pad5 + +Where ``port`` the number of the parport interface (eg. 0 for parport0). + +And ``pad1`` to ``pad5`` are pad types connected to different data input pins +(10,11,12,13,15), as described in section 2.1 of this file. + +The types are: + + ===== ============================= + Type Joystick/Pad + ===== ============================= + 0 None + 1 SNES pad + 2 NES pad + 4 Multisystem 1-button joystick + 5 Multisystem 2-button joystick + 6 N64 pad + 7 Sony PSX controller + 8 Sony PSX DDR controller + 9 SNES mouse + ===== ============================= + +The exact type of the PSX controller type is autoprobed when used, so +hot swapping should work (but is not recommended). + +Should you want to use more than one of parallel ports at once, you can use +gamecon.map2 and gamecon.map3 as additional command line parameters for two +more parallel ports. + +There are two options specific to PSX driver portion. gamecon.psx_delay sets +the command delay when talking to the controllers. The default of 25 should +work but you can try lowering it for better performance. If your pads don't +respond try raising it until they work. Setting the type to 8 allows the +driver to be used with Dance Dance Revolution or similar games. Arrow keys are +registered as key presses instead of X and Y axes. + +db9.c +----- + +Apart from making an interface, there is nothing difficult on using the +db9.c driver. It uses the following kernel/module command line:: + + db9.dev=port,type + +Where ``port`` is the number of the parport interface (eg. 0 for parport0). + +Caveat here: This driver only works on bidirectional parallel ports. If +your parallel port is recent enough, you should have no trouble with this. +Old parallel ports may not have this feature. + +``Type`` is the type of joystick or pad attached: + + ===== ====================================================== + Type Joystick/Pad + ===== ====================================================== + 0 None + 1 Multisystem 1-button joystick + 2 Multisystem 2-button joystick + 3 Genesis pad (3+1 buttons) + 5 Genesis pad (5+1 buttons) + 6 Genesis pad (6+2 buttons) + 7 Saturn pad (8 buttons) + 8 Multisystem 1-button joystick (v0.8.0.2 pin-out) + 9 Two Multisystem 1-button joysticks (v0.8.0.2 pin-out) + 10 Amiga CD32 pad + ===== ====================================================== + +Should you want to use more than one of these joysticks/pads at once, you +can use db9.dev2 and db9.dev3 as additional command line parameters for two +more joysticks/pads. + +turbografx.c +------------ + +The turbografx.c driver uses a very simple kernel/module command line:: + + turbografx.map=port,js1,js2,js3,js4,js5,js6,js7 + +Where ``port`` is the number of the parport interface (eg. 0 for parport0). + +``jsX`` is the number of buttons the Multisystem joysticks connected to the +interface ports 1-7 have. For a standard multisystem joystick, this is 1. + +Should you want to use more than one of these interfaces at once, you can +use turbografx.map2 and turbografx.map3 as additional command line parameters +for two more interfaces. + +PC parallel port pinout +======================= + +:: + + .----------------------------------------. + At the PC: \ 13 12 11 10 9 8 7 6 5 4 3 2 1 / + \ 25 24 23 22 21 20 19 18 17 16 15 14 / + ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +====== ======= ============= + Pin Name Description +====== ======= ============= + 1 /STROBE Strobe + 2-9 D0-D7 Data Bit 0-7 + 10 /ACK Acknowledge + 11 BUSY Busy + 12 PE Paper End + 13 SELIN Select In + 14 /AUTOFD Autofeed + 15 /ERROR Error + 16 /INIT Initialize + 17 /SEL Select + 18-25 GND Signal Ground +====== ======= ============= + + +That's all, folks! Have fun! diff --git a/Documentation/input/devices/ntrig.rst b/Documentation/input/devices/ntrig.rst new file mode 100644 index 000000000..1559f5349 --- /dev/null +++ b/Documentation/input/devices/ntrig.rst @@ -0,0 +1,137 @@ +.. include:: <isonum.txt> + +========================= +N-Trig touchscreen Driver +========================= + +:Copyright: |copy| 2008-2010 Rafi Rubin <rafi@seas.upenn.edu> +:Copyright: |copy| 2009-2010 Stephane Chatty + +This driver provides support for N-Trig pen and multi-touch sensors. Single +and multi-touch events are translated to the appropriate protocols for +the hid and input systems. Pen events are sufficiently hid compliant and +are left to the hid core. The driver also provides additional filtering +and utility functions accessible with sysfs and module parameters. + +This driver has been reported to work properly with multiple N-Trig devices +attached. + + +Parameters +---------- + +Note: values set at load time are global and will apply to all applicable +devices. Adjusting parameters with sysfs will override the load time values, +but only for that one device. + +The following parameters are used to configure filters to reduce noise: + ++-----------------------+-----------------------------------------------------+ +|activate_slack |number of fingers to ignore before processing events | ++-----------------------+-----------------------------------------------------+ +|activation_height, |size threshold to activate immediately | +|activation_width | | ++-----------------------+-----------------------------------------------------+ +|min_height, |size threshold below which fingers are ignored | +|min_width |both to decide activation and during activity | ++-----------------------+-----------------------------------------------------+ +|deactivate_slack |the number of "no contact" frames to ignore before | +| |propagating the end of activity events | ++-----------------------+-----------------------------------------------------+ + +When the last finger is removed from the device, it sends a number of empty +frames. By holding off on deactivation for a few frames we can tolerate false +erroneous disconnects, where the sensor may mistakenly not detect a finger that +is still present. Thus deactivate_slack addresses problems where a users might +see breaks in lines during drawing, or drop an object during a long drag. + + +Additional sysfs items +---------------------- + +These nodes just provide easy access to the ranges reported by the device. + ++-----------------------+-----------------------------------------------------+ +|sensor_logical_height, | the range for positions reported during activity | +|sensor_logical_width | | ++-----------------------+-----------------------------------------------------+ +|sensor_physical_height,| internal ranges not used for normal events but | +|sensor_physical_width | useful for tuning | ++-----------------------+-----------------------------------------------------+ + +All N-Trig devices with product id of 1 report events in the ranges of + +* X: 0-9600 +* Y: 0-7200 + +However not all of these devices have the same physical dimensions. Most +seem to be 12" sensors (Dell Latitude XT and XT2 and the HP TX2), and +at least one model (Dell Studio 17) has a 17" sensor. The ratio of physical +to logical sizes is used to adjust the size based filter parameters. + + +Filtering +--------- + +With the release of the early multi-touch firmwares it became increasingly +obvious that these sensors were prone to erroneous events. Users reported +seeing both inappropriately dropped contact and ghosts, contacts reported +where no finger was actually touching the screen. + +Deactivation slack helps prevent dropped contact for single touch use, but does +not address the problem of dropping one of more contacts while other contacts +are still active. Drops in the multi-touch context require additional +processing and should be handled in tandem with tacking. + +As observed ghost contacts are similar to actual use of the sensor, but they +seem to have different profiles. Ghost activity typically shows up as small +short lived touches. As such, I assume that the longer the continuous stream +of events the more likely those events are from a real contact, and that the +larger the size of each contact the more likely it is real. Balancing the +goals of preventing ghosts and accepting real events quickly (to minimize +user observable latency), the filter accumulates confidence for incoming +events until it hits thresholds and begins propagating. In the interest in +minimizing stored state as well as the cost of operations to make a decision, +I've kept that decision simple. + +Time is measured in terms of the number of fingers reported, not frames since +the probability of multiple simultaneous ghosts is expected to drop off +dramatically with increasing numbers. Rather than accumulate weight as a +function of size, I just use it as a binary threshold. A sufficiently large +contact immediately overrides the waiting period and leads to activation. + +Setting the activation size thresholds to large values will result in deciding +primarily on activation slack. If you see longer lived ghosts, turning up the +activation slack while reducing the size thresholds may suffice to eliminate +the ghosts while keeping the screen quite responsive to firm taps. + +Contacts continue to be filtered with min_height and min_width even after +the initial activation filter is satisfied. The intent is to provide +a mechanism for filtering out ghosts in the form of an extra finger while +you actually are using the screen. In practice this sort of ghost has +been far less problematic or relatively rare and I've left the defaults +set to 0 for both parameters, effectively turning off that filter. + +I don't know what the optimal values are for these filters. If the defaults +don't work for you, please play with the parameters. If you do find other +values more comfortable, I would appreciate feedback. + +The calibration of these devices does drift over time. If ghosts or contact +dropping worsen and interfere with the normal usage of your device, try +recalibrating it. + + +Calibration +----------- + +The N-Trig windows tools provide calibration and testing routines. Also an +unofficial unsupported set of user space tools including a calibrator is +available at: +http://code.launchpad.net/~rafi-seas/+junk/ntrig_calib + + +Tracking +-------- + +As of yet, all tested N-Trig firmwares do not track fingers. When multiple +contacts are active they seem to be sorted primarily by Y position. diff --git a/Documentation/input/devices/pxrc.rst b/Documentation/input/devices/pxrc.rst new file mode 100644 index 000000000..ca11f646b --- /dev/null +++ b/Documentation/input/devices/pxrc.rst @@ -0,0 +1,57 @@ +======================================================= +pxrc - PhoenixRC Flight Controller Adapter +======================================================= + +:Author: Marcus Folkesson <marcus.folkesson@gmail.com> + +This driver let you use your own RC controller plugged into the +adapter that comes with PhoenixRC [1]_ or other compatible adapters. + +The adapter supports 7 analog channels and 1 digital input switch. + +Notes +===== + +Many RC controllers is able to configure which stick goes to which channel. +This is also configurable in most simulators, so a matching is not necessary. + +The driver is generating the following input event for analog channels: + ++---------+----------------+ +| Channel | Event | ++=========+================+ +| 1 | ABS_X | ++---------+----------------+ +| 2 | ABS_Y | ++---------+----------------+ +| 3 | ABS_RX | ++---------+----------------+ +| 4 | ABS_RY | ++---------+----------------+ +| 5 | ABS_RUDDER | ++---------+----------------+ +| 6 | ABS_THROTTLE | ++---------+----------------+ +| 7 | ABS_MISC | ++---------+----------------+ + +The digital input switch is generated as an `BTN_A` event. + +Manual Testing +============== + +To test this driver's functionality you may use `input-event` which is part of +the `input layer utilities` suite [2]_. + +For example:: + + > modprobe pxrc + > input-events <devnr> + +To print all input events from input `devnr`. + +References +========== + +.. [1] http://www.phoenix-sim.com/ +.. [2] https://www.kraxel.org/cgit/input/ diff --git a/Documentation/input/devices/rotary-encoder.rst b/Documentation/input/devices/rotary-encoder.rst new file mode 100644 index 000000000..5865748c1 --- /dev/null +++ b/Documentation/input/devices/rotary-encoder.rst @@ -0,0 +1,135 @@ +============================================================ +rotary-encoder - a generic driver for GPIO connected devices +============================================================ + +:Author: Daniel Mack <daniel@caiaq.de>, Feb 2009 + +Function +-------- + +Rotary encoders are devices which are connected to the CPU or other +peripherals with two wires. The outputs are phase-shifted by 90 degrees +and by triggering on falling and rising edges, the turn direction can +be determined. + +Some encoders have both outputs low in stable states, others also have +a stable state with both outputs high (half-period mode) and some have +a stable state in all steps (quarter-period mode). + +The phase diagram of these two outputs look like this:: + + _____ _____ _____ + | | | | | | + Channel A ____| |_____| |_____| |____ + + : : : : : : : : : : : : + __ _____ _____ _____ + | | | | | | | + Channel B |_____| |_____| |_____| |__ + + : : : : : : : : : : : : + Event a b c d a b c d a b c d + + |<-------->| + one step + + |<-->| + one step (half-period mode) + + |<>| + one step (quarter-period mode) + +For more information, please see + https://en.wikipedia.org/wiki/Rotary_encoder + + +Events / state machine +---------------------- + +In half-period mode, state a) and c) above are used to determine the +rotational direction based on the last stable state. Events are reported in +states b) and d) given that the new stable state is different from the last +(i.e. the rotation was not reversed half-way). + +Otherwise, the following apply: + +a) Rising edge on channel A, channel B in low state + This state is used to recognize a clockwise turn + +b) Rising edge on channel B, channel A in high state + When entering this state, the encoder is put into 'armed' state, + meaning that there it has seen half the way of a one-step transition. + +c) Falling edge on channel A, channel B in high state + This state is used to recognize a counter-clockwise turn + +d) Falling edge on channel B, channel A in low state + Parking position. If the encoder enters this state, a full transition + should have happened, unless it flipped back on half the way. The + 'armed' state tells us about that. + +Platform requirements +--------------------- + +As there is no hardware dependent call in this driver, the platform it is +used with must support gpiolib. Another requirement is that IRQs must be +able to fire on both edges. + + +Board integration +----------------- + +To use this driver in your system, register a platform_device with the +name 'rotary-encoder' and associate the IRQs and some specific platform +data with it. Because the driver uses generic device properties, this can +be done either via device tree, ACPI, or using static board files, like in +example below: + +:: + + /* board support file example */ + + #include <linux/input.h> + #include <linux/gpio/machine.h> + #include <linux/property.h> + + #define GPIO_ROTARY_A 1 + #define GPIO_ROTARY_B 2 + + static struct gpiod_lookup_table rotary_encoder_gpios = { + .dev_id = "rotary-encoder.0", + .table = { + GPIO_LOOKUP_IDX("gpio-0", + GPIO_ROTARY_A, NULL, 0, GPIO_ACTIVE_LOW), + GPIO_LOOKUP_IDX("gpio-0", + GPIO_ROTARY_B, NULL, 1, GPIO_ACTIVE_HIGH), + { }, + }, + }; + + static const struct property_entry rotary_encoder_properties[] = { + PROPERTY_ENTRY_U32("rotary-encoder,steps-per-period", 24), + PROPERTY_ENTRY_U32("linux,axis", ABS_X), + PROPERTY_ENTRY_U32("rotary-encoder,relative_axis", 0), + { }, + }; + + static const struct software_node rotary_encoder_node = { + .properties = rotary_encoder_properties, + }; + + static struct platform_device rotary_encoder_device = { + .name = "rotary-encoder", + .id = 0, + }; + + ... + + gpiod_add_lookup_table(&rotary_encoder_gpios); + device_add_software_node(&rotary_encoder_device.dev, &rotary_encoder_node); + platform_device_register(&rotary_encoder_device); + + ... + +Please consult device tree binding documentation to see all properties +supported by the driver. diff --git a/Documentation/input/devices/sentelic.rst b/Documentation/input/devices/sentelic.rst new file mode 100644 index 000000000..d7ad603dd --- /dev/null +++ b/Documentation/input/devices/sentelic.rst @@ -0,0 +1,901 @@ +.. include:: <isonum.txt> + +================= +Sentelic Touchpad +================= + + +:Copyright: |copy| 2002-2011 Sentelic Corporation. + +:Last update: Dec-07-2011 + +Finger Sensing Pad Intellimouse Mode (scrolling wheel, 4th and 5th buttons) +============================================================================ + +A) MSID 4: Scrolling wheel mode plus Forward page(4th button) and Backward + page (5th button) + +1. Set sample rate to 200; +2. Set sample rate to 200; +3. Set sample rate to 80; +4. Issuing the "Get device ID" command (0xF2) and waits for the response; +5. FSP will respond 0x04. + +:: + + Packet 1 + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |Y|X|y|x|1|M|R|L| 2 |X|X|X|X|X|X|X|X| 3 |Y|Y|Y|Y|Y|Y|Y|Y| 4 | | |B|F|W|W|W|W| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7 => Y overflow + Bit6 => X overflow + Bit5 => Y sign bit + Bit4 => X sign bit + Bit3 => 1 + Bit2 => Middle Button, 1 is pressed, 0 is not pressed. + Bit1 => Right Button, 1 is pressed, 0 is not pressed. + Bit0 => Left Button, 1 is pressed, 0 is not pressed. + Byte 2: X Movement(9-bit 2's complement integers) + Byte 3: Y Movement(9-bit 2's complement integers) + Byte 4: Bit3~Bit0 => the scrolling wheel's movement since the last data report. + valid values, -8 ~ +7 + Bit4 => 1 = 4th mouse button is pressed, Forward one page. + 0 = 4th mouse button is not pressed. + Bit5 => 1 = 5th mouse button is pressed, Backward one page. + 0 = 5th mouse button is not pressed. + +B) MSID 6: Horizontal and Vertical scrolling + +- Set bit 1 in register 0x40 to 1 + +FSP replaces scrolling wheel's movement as 4 bits to show horizontal and +vertical scrolling. + +:: + + Packet 1 + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |Y|X|y|x|1|M|R|L| 2 |X|X|X|X|X|X|X|X| 3 |Y|Y|Y|Y|Y|Y|Y|Y| 4 | | |B|F|r|l|u|d| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7 => Y overflow + Bit6 => X overflow + Bit5 => Y sign bit + Bit4 => X sign bit + Bit3 => 1 + Bit2 => Middle Button, 1 is pressed, 0 is not pressed. + Bit1 => Right Button, 1 is pressed, 0 is not pressed. + Bit0 => Left Button, 1 is pressed, 0 is not pressed. + Byte 2: X Movement(9-bit 2's complement integers) + Byte 3: Y Movement(9-bit 2's complement integers) + Byte 4: Bit0 => the Vertical scrolling movement downward. + Bit1 => the Vertical scrolling movement upward. + Bit2 => the Horizontal scrolling movement leftward. + Bit3 => the Horizontal scrolling movement rightward. + Bit4 => 1 = 4th mouse button is pressed, Forward one page. + 0 = 4th mouse button is not pressed. + Bit5 => 1 = 5th mouse button is pressed, Backward one page. + 0 = 5th mouse button is not pressed. + +C) MSID 7 + +FSP uses 2 packets (8 Bytes) to represent Absolute Position. +so we have PACKET NUMBER to identify packets. + + If PACKET NUMBER is 0, the packet is Packet 1. + If PACKET NUMBER is 1, the packet is Packet 2. + Please count this number in program. + +MSID6 special packet will be enable at the same time when enable MSID 7. + +Absolute position for STL3886-G0 +================================ + +1. Set bit 2 or 3 in register 0x40 to 1 +2. Set bit 6 in register 0x40 to 1 + +:: + + Packet 1 (ABSOLUTE POSITION) + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |0|1|V|1|1|M|R|L| 2 |X|X|X|X|X|X|X|X| 3 |Y|Y|Y|Y|Y|Y|Y|Y| 4 |r|l|d|u|X|X|Y|Y| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7~Bit6 => 00, Normal data packet + => 01, Absolute coordination packet + => 10, Notify packet + Bit5 => valid bit + Bit4 => 1 + Bit3 => 1 + Bit2 => Middle Button, 1 is pressed, 0 is not pressed. + Bit1 => Right Button, 1 is pressed, 0 is not pressed. + Bit0 => Left Button, 1 is pressed, 0 is not pressed. + Byte 2: X coordinate (xpos[9:2]) + Byte 3: Y coordinate (ypos[9:2]) + Byte 4: Bit1~Bit0 => Y coordinate (xpos[1:0]) + Bit3~Bit2 => X coordinate (ypos[1:0]) + Bit4 => scroll up + Bit5 => scroll down + Bit6 => scroll left + Bit7 => scroll right + + Notify Packet for G0 + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |1|0|0|1|1|M|R|L| 2 |C|C|C|C|C|C|C|C| 3 |M|M|M|M|M|M|M|M| 4 |0|0|0|0|0|0|0|0| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7~Bit6 => 00, Normal data packet + => 01, Absolute coordination packet + => 10, Notify packet + Bit5 => 0 + Bit4 => 1 + Bit3 => 1 + Bit2 => Middle Button, 1 is pressed, 0 is not pressed. + Bit1 => Right Button, 1 is pressed, 0 is not pressed. + Bit0 => Left Button, 1 is pressed, 0 is not pressed. + Byte 2: Message Type => 0x5A (Enable/Disable status packet) + Mode Type => 0xA5 (Normal/Icon mode status) + Byte 3: Message Type => 0x00 (Disabled) + => 0x01 (Enabled) + Mode Type => 0x00 (Normal) + => 0x01 (Icon) + Byte 4: Bit7~Bit0 => Don't Care + +Absolute position for STL3888-Ax +================================ + +:: + + Packet 1 (ABSOLUTE POSITION) + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |0|1|V|A|1|L|0|1| 2 |X|X|X|X|X|X|X|X| 3 |Y|Y|Y|Y|Y|Y|Y|Y| 4 |x|x|y|y|X|X|Y|Y| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7~Bit6 => 00, Normal data packet + => 01, Absolute coordination packet + => 10, Notify packet + => 11, Normal data packet with on-pad click + Bit5 => Valid bit, 0 means that the coordinate is invalid or finger up. + When both fingers are up, the last two reports have zero valid + bit. + Bit4 => arc + Bit3 => 1 + Bit2 => Left Button, 1 is pressed, 0 is released. + Bit1 => 0 + Bit0 => 1 + Byte 2: X coordinate (xpos[9:2]) + Byte 3: Y coordinate (ypos[9:2]) + Byte 4: Bit1~Bit0 => Y coordinate (xpos[1:0]) + Bit3~Bit2 => X coordinate (ypos[1:0]) + Bit5~Bit4 => y1_g + Bit7~Bit6 => x1_g + + Packet 2 (ABSOLUTE POSITION) + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |0|1|V|A|1|R|1|0| 2 |X|X|X|X|X|X|X|X| 3 |Y|Y|Y|Y|Y|Y|Y|Y| 4 |x|x|y|y|X|X|Y|Y| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7~Bit6 => 00, Normal data packet + => 01, Absolute coordinates packet + => 10, Notify packet + => 11, Normal data packet with on-pad click + Bit5 => Valid bit, 0 means that the coordinate is invalid or finger up. + When both fingers are up, the last two reports have zero valid + bit. + Bit4 => arc + Bit3 => 1 + Bit2 => Right Button, 1 is pressed, 0 is released. + Bit1 => 1 + Bit0 => 0 + Byte 2: X coordinate (xpos[9:2]) + Byte 3: Y coordinate (ypos[9:2]) + Byte 4: Bit1~Bit0 => Y coordinate (xpos[1:0]) + Bit3~Bit2 => X coordinate (ypos[1:0]) + Bit5~Bit4 => y2_g + Bit7~Bit6 => x2_g + + Notify Packet for STL3888-Ax + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |1|0|1|P|1|M|R|L| 2 |C|C|C|C|C|C|C|C| 3 |0|0|F|F|0|0|0|i| 4 |r|l|d|u|0|0|0|0| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7~Bit6 => 00, Normal data packet + => 01, Absolute coordinates packet + => 10, Notify packet + => 11, Normal data packet with on-pad click + Bit5 => 1 + Bit4 => when in absolute coordinates mode (valid when EN_PKT_GO is 1): + 0: left button is generated by the on-pad command + 1: left button is generated by the external button + Bit3 => 1 + Bit2 => Middle Button, 1 is pressed, 0 is not pressed. + Bit1 => Right Button, 1 is pressed, 0 is not pressed. + Bit0 => Left Button, 1 is pressed, 0 is not pressed. + Byte 2: Message Type => 0xB7 (Multi Finger, Multi Coordinate mode) + Byte 3: Bit7~Bit6 => Don't care + Bit5~Bit4 => Number of fingers + Bit3~Bit1 => Reserved + Bit0 => 1: enter gesture mode; 0: leaving gesture mode + Byte 4: Bit7 => scroll right button + Bit6 => scroll left button + Bit5 => scroll down button + Bit4 => scroll up button + * Note that if gesture and additional button (Bit4~Bit7) + happen at the same time, the button information will not + be sent. + Bit3~Bit0 => Reserved + +Sample sequence of Multi-finger, Multi-coordinate mode: + + notify packet (valid bit == 1), abs pkt 1, abs pkt 2, abs pkt 1, + abs pkt 2, ..., notify packet (valid bit == 0) + +Absolute position for STL3888-B0 +================================ + +:: + + Packet 1(ABSOLUTE POSITION) + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |0|1|V|F|1|0|R|L| 2 |X|X|X|X|X|X|X|X| 3 |Y|Y|Y|Y|Y|Y|Y|Y| 4 |r|l|u|d|X|X|Y|Y| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7~Bit6 => 00, Normal data packet + => 01, Absolute coordinates packet + => 10, Notify packet + => 11, Normal data packet with on-pad click + Bit5 => Valid bit, 0 means that the coordinate is invalid or finger up. + When both fingers are up, the last two reports have zero valid + bit. + Bit4 => finger up/down information. 1: finger down, 0: finger up. + Bit3 => 1 + Bit2 => finger index, 0 is the first finger, 1 is the second finger. + Bit1 => Right Button, 1 is pressed, 0 is not pressed. + Bit0 => Left Button, 1 is pressed, 0 is not pressed. + Byte 2: X coordinate (xpos[9:2]) + Byte 3: Y coordinate (ypos[9:2]) + Byte 4: Bit1~Bit0 => Y coordinate (xpos[1:0]) + Bit3~Bit2 => X coordinate (ypos[1:0]) + Bit4 => scroll down button + Bit5 => scroll up button + Bit6 => scroll left button + Bit7 => scroll right button + + Packet 2 (ABSOLUTE POSITION) + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |0|1|V|F|1|1|R|L| 2 |X|X|X|X|X|X|X|X| 3 |Y|Y|Y|Y|Y|Y|Y|Y| 4 |r|l|u|d|X|X|Y|Y| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7~Bit6 => 00, Normal data packet + => 01, Absolute coordination packet + => 10, Notify packet + => 11, Normal data packet with on-pad click + Bit5 => Valid bit, 0 means that the coordinate is invalid or finger up. + When both fingers are up, the last two reports have zero valid + bit. + Bit4 => finger up/down information. 1: finger down, 0: finger up. + Bit3 => 1 + Bit2 => finger index, 0 is the first finger, 1 is the second finger. + Bit1 => Right Button, 1 is pressed, 0 is not pressed. + Bit0 => Left Button, 1 is pressed, 0 is not pressed. + Byte 2: X coordinate (xpos[9:2]) + Byte 3: Y coordinate (ypos[9:2]) + Byte 4: Bit1~Bit0 => Y coordinate (xpos[1:0]) + Bit3~Bit2 => X coordinate (ypos[1:0]) + Bit4 => scroll down button + Bit5 => scroll up button + Bit6 => scroll left button + Bit7 => scroll right button + +Notify Packet for STL3888-B0:: + + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |1|0|1|P|1|M|R|L| 2 |C|C|C|C|C|C|C|C| 3 |0|0|F|F|0|0|0|i| 4 |r|l|u|d|0|0|0|0| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7~Bit6 => 00, Normal data packet + => 01, Absolute coordination packet + => 10, Notify packet + => 11, Normal data packet with on-pad click + Bit5 => 1 + Bit4 => when in absolute coordinates mode (valid when EN_PKT_GO is 1): + 0: left button is generated by the on-pad command + 1: left button is generated by the external button + Bit3 => 1 + Bit2 => Middle Button, 1 is pressed, 0 is not pressed. + Bit1 => Right Button, 1 is pressed, 0 is not pressed. + Bit0 => Left Button, 1 is pressed, 0 is not pressed. + Byte 2: Message Type => 0xB7 (Multi Finger, Multi Coordinate mode) + Byte 3: Bit7~Bit6 => Don't care + Bit5~Bit4 => Number of fingers + Bit3~Bit1 => Reserved + Bit0 => 1: enter gesture mode; 0: leaving gesture mode + Byte 4: Bit7 => scroll right button + Bit6 => scroll left button + Bit5 => scroll up button + Bit4 => scroll down button + * Note that if gesture and additional button(Bit4~Bit7) + happen at the same time, the button information will not + be sent. + Bit3~Bit0 => Reserved + +Sample sequence of Multi-finger, Multi-coordinate mode: + + notify packet (valid bit == 1), abs pkt 1, abs pkt 2, abs pkt 1, + abs pkt 2, ..., notify packet (valid bit == 0) + +Absolute position for STL3888-Cx and STL3888-Dx +=============================================== + +:: + + Single Finger, Absolute Coordinate Mode (SFAC) + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |0|1|0|P|1|M|R|L| 2 |X|X|X|X|X|X|X|X| 3 |Y|Y|Y|Y|Y|Y|Y|Y| 4 |r|l|B|F|X|X|Y|Y| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7~Bit6 => 00, Normal data packet + => 01, Absolute coordinates packet + => 10, Notify packet + Bit5 => Coordinate mode(always 0 in SFAC mode): + 0: single-finger absolute coordinates (SFAC) mode + 1: multi-finger, multiple coordinates (MFMC) mode + Bit4 => 0: The LEFT button is generated by on-pad command (OPC) + 1: The LEFT button is generated by external button + Default is 1 even if the LEFT button is not pressed. + Bit3 => Always 1, as specified by PS/2 protocol. + Bit2 => Middle Button, 1 is pressed, 0 is not pressed. + Bit1 => Right Button, 1 is pressed, 0 is not pressed. + Bit0 => Left Button, 1 is pressed, 0 is not pressed. + Byte 2: X coordinate (xpos[9:2]) + Byte 3: Y coordinate (ypos[9:2]) + Byte 4: Bit1~Bit0 => Y coordinate (xpos[1:0]) + Bit3~Bit2 => X coordinate (ypos[1:0]) + Bit4 => 4th mouse button(forward one page) + Bit5 => 5th mouse button(backward one page) + Bit6 => scroll left button + Bit7 => scroll right button + + Multi Finger, Multiple Coordinates Mode (MFMC): + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |0|1|1|P|1|F|R|L| 2 |X|X|X|X|X|X|X|X| 3 |Y|Y|Y|Y|Y|Y|Y|Y| 4 |r|l|B|F|X|X|Y|Y| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7~Bit6 => 00, Normal data packet + => 01, Absolute coordination packet + => 10, Notify packet + Bit5 => Coordinate mode (always 1 in MFMC mode): + 0: single-finger absolute coordinates (SFAC) mode + 1: multi-finger, multiple coordinates (MFMC) mode + Bit4 => 0: The LEFT button is generated by on-pad command (OPC) + 1: The LEFT button is generated by external button + Default is 1 even if the LEFT button is not pressed. + Bit3 => Always 1, as specified by PS/2 protocol. + Bit2 => Finger index, 0 is the first finger, 1 is the second finger. + If bit 1 and 0 are all 1 and bit 4 is 0, the middle external + button is pressed. + Bit1 => Right Button, 1 is pressed, 0 is not pressed. + Bit0 => Left Button, 1 is pressed, 0 is not pressed. + Byte 2: X coordinate (xpos[9:2]) + Byte 3: Y coordinate (ypos[9:2]) + Byte 4: Bit1~Bit0 => Y coordinate (xpos[1:0]) + Bit3~Bit2 => X coordinate (ypos[1:0]) + Bit4 => 4th mouse button(forward one page) + Bit5 => 5th mouse button(backward one page) + Bit6 => scroll left button + Bit7 => scroll right button + +When one of the two fingers is up, the device will output four consecutive +MFMC#0 report packets with zero X and Y to represent 1st finger is up or +four consecutive MFMC#1 report packets with zero X and Y to represent that +the 2nd finger is up. On the other hand, if both fingers are up, the device +will output four consecutive single-finger, absolute coordinate(SFAC) packets +with zero X and Y. + +Notify Packet for STL3888-Cx/Dx:: + + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |1|0|0|P|1|M|R|L| 2 |C|C|C|C|C|C|C|C| 3 |0|0|F|F|0|0|0|i| 4 |r|l|u|d|0|0|0|0| + |---------------| |---------------| |---------------| |---------------| + + Byte 1: Bit7~Bit6 => 00, Normal data packet + => 01, Absolute coordinates packet + => 10, Notify packet + Bit5 => Always 0 + Bit4 => 0: The LEFT button is generated by on-pad command(OPC) + 1: The LEFT button is generated by external button + Default is 1 even if the LEFT button is not pressed. + Bit3 => 1 + Bit2 => Middle Button, 1 is pressed, 0 is not pressed. + Bit1 => Right Button, 1 is pressed, 0 is not pressed. + Bit0 => Left Button, 1 is pressed, 0 is not pressed. + Byte 2: Message type: + 0xba => gesture information + 0xc0 => one finger hold-rotating gesture + Byte 3: The first parameter for the received message: + 0xba => gesture ID (refer to the 'Gesture ID' section) + 0xc0 => region ID + Byte 4: The second parameter for the received message: + 0xba => N/A + 0xc0 => finger up/down information + +Sample sequence of Multi-finger, Multi-coordinates mode: + + notify packet (valid bit == 1), MFMC packet 1 (byte 1, bit 2 == 0), + MFMC packet 2 (byte 1, bit 2 == 1), MFMC packet 1, MFMC packet 2, + ..., notify packet (valid bit == 0) + + That is, when the device is in MFMC mode, the host will receive + interleaved absolute coordinate packets for each finger. + +FSP Enable/Disable packet +========================= + +:: + + Bit 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 + BYTE |---------------|BYTE |---------------|BYTE|---------------|BYTE|---------------| + 1 |Y|X|0|0|1|M|R|L| 2 |0|1|0|1|1|0|1|E| 3 | | | | | | | | | 4 | | | | | | | | | + |---------------| |---------------| |---------------| |---------------| + + FSP will send out enable/disable packet when FSP receive PS/2 enable/disable + command. Host will receive the packet which Middle, Right, Left button will + be set. The packet only use byte 0 and byte 1 as a pattern of original packet. + Ignore the other bytes of the packet. + + Byte 1: Bit7 => 0, Y overflow + Bit6 => 0, X overflow + Bit5 => 0, Y sign bit + Bit4 => 0, X sign bit + Bit3 => 1 + Bit2 => 1, Middle Button + Bit1 => 1, Right Button + Bit0 => 1, Left Button + Byte 2: Bit7~1 => (0101101b) + Bit0 => 1 = Enable + 0 = Disable + Byte 3: Don't care + Byte 4: Don't care (MOUSE ID 3, 4) + Byte 5~8: Don't care (Absolute packet) + +PS/2 Command Set +================ + +FSP supports basic PS/2 commanding set and modes, refer to following URL for +details about PS/2 commands: + +http://www.computer-engineering.org/ps2mouse/ + +Programming Sequence for Determining Packet Parsing Flow +======================================================== + +1. Identify FSP by reading device ID(0x00) and version(0x01) register + +2. For FSP version < STL3888 Cx, determine number of buttons by reading + the 'test mode status' (0x20) register:: + + buttons = reg[0x20] & 0x30 + + if buttons == 0x30 or buttons == 0x20: + # two/four buttons + Refer to 'Finger Sensing Pad PS/2 Mouse Intellimouse' + section A for packet parsing detail(ignore byte 4, bit ~ 7) + elif buttons == 0x10: + # 6 buttons + Refer to 'Finger Sensing Pad PS/2 Mouse Intellimouse' + section B for packet parsing detail + elif buttons == 0x00: + # 6 buttons + Refer to 'Finger Sensing Pad PS/2 Mouse Intellimouse' + section A for packet parsing detail + +3. For FSP version >= STL3888 Cx: + Refer to 'Finger Sensing Pad PS/2 Mouse Intellimouse' + section A for packet parsing detail (ignore byte 4, bit ~ 7) + +Programming Sequence for Register Reading/Writing +================================================= + +Register inversion requirement: + +Following values needed to be inverted(the '~' operator in C) before being +sent to FSP:: + + 0xe8, 0xe9, 0xee, 0xf2, 0xf3 and 0xff. + +Register swapping requirement: + +Following values needed to have their higher 4 bits and lower 4 bits being +swapped before being sent to FSP:: + + 10, 20, 40, 60, 80, 100 and 200. + +Register reading sequence: + + 1. send 0xf3 PS/2 command to FSP; + + 2. send 0x66 PS/2 command to FSP; + + 3. send 0x88 PS/2 command to FSP; + + 4. send 0xf3 PS/2 command to FSP; + + 5. if the register address being to read is not required to be + inverted(refer to the 'Register inversion requirement' section), + goto step 6 + + a. send 0x68 PS/2 command to FSP; + + b. send the inverted register address to FSP and goto step 8; + + 6. if the register address being to read is not required to be + swapped(refer to the 'Register swapping requirement' section), + goto step 7 + + a. send 0xcc PS/2 command to FSP; + + b. send the swapped register address to FSP and goto step 8; + + 7. send 0x66 PS/2 command to FSP; + + a. send the original register address to FSP and goto step 8; + + 8. send 0xe9(status request) PS/2 command to FSP; + + 9. the 4th byte of the response read from FSP should be the + requested register value(?? indicates don't care byte):: + + host: 0xe9 + 3888: 0xfa (??) (??) (val) + + * Note that since the Cx release, the hardware will return 1's + complement of the register value at the 3rd byte of status request + result:: + + host: 0xe9 + 3888: 0xfa (??) (~val) (val) + +Register writing sequence: + + 1. send 0xf3 PS/2 command to FSP; + + 2. if the register address being to write is not required to be + inverted(refer to the 'Register inversion requirement' section), + goto step 3 + + a. send 0x74 PS/2 command to FSP; + + b. send the inverted register address to FSP and goto step 5; + + 3. if the register address being to write is not required to be + swapped(refer to the 'Register swapping requirement' section), + goto step 4 + + a. send 0x77 PS/2 command to FSP; + + b. send the swapped register address to FSP and goto step 5; + + 4. send 0x55 PS/2 command to FSP; + + a. send the register address to FSP and goto step 5; + + 5. send 0xf3 PS/2 command to FSP; + + 6. if the register value being to write is not required to be + inverted(refer to the 'Register inversion requirement' section), + goto step 7 + + a. send 0x47 PS/2 command to FSP; + + b. send the inverted register value to FSP and goto step 9; + + 7. if the register value being to write is not required to be + swapped(refer to the 'Register swapping requirement' section), + goto step 8 + + a. send 0x44 PS/2 command to FSP; + + b. send the swapped register value to FSP and goto step 9; + + 8. send 0x33 PS/2 command to FSP; + + a. send the register value to FSP; + + 9. the register writing sequence is completed. + + * Since the Cx release, the hardware will return 1's + complement of the register value at the 3rd byte of status request + result. Host can optionally send another 0xe9 (status request) PS/2 + command to FSP at the end of register writing to verify that the + register writing operation is successful (?? indicates don't care + byte):: + + host: 0xe9 + 3888: 0xfa (??) (~val) (val) + +Programming Sequence for Page Register Reading/Writing +====================================================== + +In order to overcome the limitation of maximum number of registers +supported, the hardware separates register into different groups called +'pages.' Each page is able to include up to 255 registers. + +The default page after power up is 0x82; therefore, if one has to get +access to register 0x8301, one has to use following sequence to switch +to page 0x83, then start reading/writing from/to offset 0x01 by using +the register read/write sequence described in previous section. + +Page register reading sequence: + + 1. send 0xf3 PS/2 command to FSP; + + 2. send 0x66 PS/2 command to FSP; + + 3. send 0x88 PS/2 command to FSP; + + 4. send 0xf3 PS/2 command to FSP; + + 5. send 0x83 PS/2 command to FSP; + + 6. send 0x88 PS/2 command to FSP; + + 7. send 0xe9(status request) PS/2 command to FSP; + + 8. the response read from FSP should be the requested page value. + + +Page register writing sequence: + + 1. send 0xf3 PS/2 command to FSP; + + 2. send 0x38 PS/2 command to FSP; + + 3. send 0x88 PS/2 command to FSP; + + 4. send 0xf3 PS/2 command to FSP; + + 5. if the page address being written is not required to be + inverted(refer to the 'Register inversion requirement' section), + goto step 6 + + a. send 0x47 PS/2 command to FSP; + + b. send the inverted page address to FSP and goto step 9; + + 6. if the page address being written is not required to be + swapped(refer to the 'Register swapping requirement' section), + goto step 7 + + a. send 0x44 PS/2 command to FSP; + + b. send the swapped page address to FSP and goto step 9; + + 7. send 0x33 PS/2 command to FSP; + + 8. send the page address to FSP; + + 9. the page register writing sequence is completed. + +Gesture ID +========== + +Unlike other devices which sends multiple fingers' coordinates to host, +FSP processes multiple fingers' coordinates internally and convert them +into a 8 bits integer, namely 'Gesture ID.' Following is a list of +supported gesture IDs: + + ======= ================================== + ID Description + ======= ================================== + 0x86 2 finger straight up + 0x82 2 finger straight down + 0x80 2 finger straight right + 0x84 2 finger straight left + 0x8f 2 finger zoom in + 0x8b 2 finger zoom out + 0xc0 2 finger curve, counter clockwise + 0xc4 2 finger curve, clockwise + 0x2e 3 finger straight up + 0x2a 3 finger straight down + 0x28 3 finger straight right + 0x2c 3 finger straight left + 0x38 palm + ======= ================================== + +Register Listing +================ + +Registers are represented in 16 bits values. The higher 8 bits represent +the page address and the lower 8 bits represent the relative offset within +that particular page. Refer to the 'Programming Sequence for Page Register +Reading/Writing' section for instructions on how to change current page +address:: + + offset width default r/w name + 0x8200 bit7~bit0 0x01 RO device ID + + 0x8201 bit7~bit0 RW version ID + 0xc1: STL3888 Ax + 0xd0 ~ 0xd2: STL3888 Bx + 0xe0 ~ 0xe1: STL3888 Cx + 0xe2 ~ 0xe3: STL3888 Dx + + 0x8202 bit7~bit0 0x01 RO vendor ID + + 0x8203 bit7~bit0 0x01 RO product ID + + 0x8204 bit3~bit0 0x01 RW revision ID + + 0x820b test mode status 1 + bit3 1 RO 0: rotate 180 degree + 1: no rotation + *only supported by H/W prior to Cx + + 0x820f register file page control + bit2 0 RW 1: rotate 180 degree + 0: no rotation + *supported since Cx + + bit0 0 RW 1 to enable page 1 register files + *only supported by H/W prior to Cx + + 0x8210 RW system control 1 + bit0 1 RW Reserved, must be 1 + bit1 0 RW Reserved, must be 0 + bit4 0 RW Reserved, must be 0 + bit5 1 RW register clock gating enable + 0: read only, 1: read/write enable + (Note that following registers does not require clock gating being + enabled prior to write: 05 06 07 08 09 0c 0f 10 11 12 16 17 18 23 2e + 40 41 42 43. In addition to that, this bit must be 1 when gesture + mode is enabled) + + 0x8220 test mode status + bit5~bit4 RO number of buttons + 11 => 2, lbtn/rbtn + 10 => 4, lbtn/rbtn/scru/scrd + 01 => 6, lbtn/rbtn/scru/scrd/scrl/scrr + 00 => 6, lbtn/rbtn/scru/scrd/fbtn/bbtn + *only supported by H/W prior to Cx + + 0x8231 RW on-pad command detection + bit7 0 RW on-pad command left button down tag + enable + 0: disable, 1: enable + *only supported by H/W prior to Cx + + 0x8234 RW on-pad command control 5 + bit4~bit0 0x05 RW XLO in 0s/4/1, so 03h = 0010.1b = 2.5 + (Note that position unit is in 0.5 scanline) + *only supported by H/W prior to Cx + + bit7 0 RW on-pad tap zone enable + 0: disable, 1: enable + *only supported by H/W prior to Cx + + 0x8235 RW on-pad command control 6 + bit4~bit0 0x1d RW XHI in 0s/4/1, so 19h = 1100.1b = 12.5 + (Note that position unit is in 0.5 scanline) + *only supported by H/W prior to Cx + + 0x8236 RW on-pad command control 7 + bit4~bit0 0x04 RW YLO in 0s/4/1, so 03h = 0010.1b = 2.5 + (Note that position unit is in 0.5 scanline) + *only supported by H/W prior to Cx + + 0x8237 RW on-pad command control 8 + bit4~bit0 0x13 RW YHI in 0s/4/1, so 11h = 1000.1b = 8.5 + (Note that position unit is in 0.5 scanline) + *only supported by H/W prior to Cx + + 0x8240 RW system control 5 + bit1 0 RW FSP Intellimouse mode enable + 0: disable, 1: enable + *only supported by H/W prior to Cx + + bit2 0 RW movement + abs. coordinate mode enable + 0: disable, 1: enable + (Note that this function has the functionality of bit 1 even when + bit 1 is not set. However, the format is different from that of bit 1. + In addition, when bit 1 and bit 2 are set at the same time, bit 2 will + override bit 1.) + *only supported by H/W prior to Cx + + bit3 0 RW abs. coordinate only mode enable + 0: disable, 1: enable + (Note that this function has the functionality of bit 1 even when + bit 1 is not set. However, the format is different from that of bit 1. + In addition, when bit 1, bit 2 and bit 3 are set at the same time, + bit 3 will override bit 1 and 2.) + *only supported by H/W prior to Cx + + bit5 0 RW auto switch enable + 0: disable, 1: enable + *only supported by H/W prior to Cx + + bit6 0 RW G0 abs. + notify packet format enable + 0: disable, 1: enable + (Note that the absolute/relative coordinate output still depends on + bit 2 and 3. That is, if any of those bit is 1, host will receive + absolute coordinates; otherwise, host only receives packets with + relative coordinate.) + *only supported by H/W prior to Cx + + bit7 0 RW EN_PS2_F2: PS/2 gesture mode 2nd + finger packet enable + 0: disable, 1: enable + *only supported by H/W prior to Cx + + 0x8243 RW on-pad control + bit0 0 RW on-pad control enable + 0: disable, 1: enable + (Note that if this bit is cleared, bit 3/5 will be ineffective) + *only supported by H/W prior to Cx + + bit3 0 RW on-pad fix vertical scrolling enable + 0: disable, 1: enable + *only supported by H/W prior to Cx + + bit5 0 RW on-pad fix horizontal scrolling enable + 0: disable, 1: enable + *only supported by H/W prior to Cx + + 0x8290 RW software control register 1 + bit0 0 RW absolute coordination mode + 0: disable, 1: enable + *supported since Cx + + bit1 0 RW gesture ID output + 0: disable, 1: enable + *supported since Cx + + bit2 0 RW two fingers' coordinates output + 0: disable, 1: enable + *supported since Cx + + bit3 0 RW finger up one packet output + 0: disable, 1: enable + *supported since Cx + + bit4 0 RW absolute coordination continuous mode + 0: disable, 1: enable + *supported since Cx + + bit6~bit5 00 RW gesture group selection + 00: basic + 01: suite + 10: suite pro + 11: advanced + *supported since Cx + + bit7 0 RW Bx packet output compatible mode + 0: disable, 1: enable + *supported since Cx + *supported since Cx + + + 0x833d RW on-pad command control 1 + bit7 1 RW on-pad command detection enable + 0: disable, 1: enable + *supported since Cx + + 0x833e RW on-pad command detection + bit7 0 RW on-pad command left button down tag + enable. Works only in H/W based PS/2 + data packet mode. + 0: disable, 1: enable + *supported since Cx diff --git a/Documentation/input/devices/walkera0701.rst b/Documentation/input/devices/walkera0701.rst new file mode 100644 index 000000000..2adda99ca --- /dev/null +++ b/Documentation/input/devices/walkera0701.rst @@ -0,0 +1,128 @@ +=========================== +Walkera WK-0701 transmitter +=========================== + +Walkera WK-0701 transmitter is supplied with a ready to fly Walkera +helicopters such as HM36, HM37, HM60. The walkera0701 module enables to use +this transmitter as joystick + +Devel homepage and download: +http://zub.fei.tuke.sk/walkera-wk0701/ + +or use cogito: +cg-clone http://zub.fei.tuke.sk/GIT/walkera0701-joystick + + +Connecting to PC +================ + +At back side of transmitter S-video connector can be found. Modulation +pulses from processor to HF part can be found at pin 2 of this connector, +pin 3 is GND. Between pin 3 and CPU 5k6 resistor can be found. To get +modulation pulses to PC, signal pulses must be amplified. + +Cable: (walkera TX to parport) + +Walkera WK-0701 TX S-VIDEO connector:: + + (back side of TX) + __ __ S-video: canon25 + / |_| \ pin 2 (signal) NPN parport + / O 4 3 O \ pin 3 (GND) LED ________________ 10 ACK + ( O 2 1 O ) | C + \ ___ / 2 ________________________|\|_____|/ + | [___] | |/| B |\ + ------- 3 __________________________________|________________ 25 GND + E + +I use green LED and BC109 NPN transistor. + +Software +======== + +Build kernel with walkera0701 module. Module walkera0701 need exclusive +access to parport, modules like lp must be unloaded before loading +walkera0701 module, check dmesg for error messages. Connect TX to PC by +cable and run jstest /dev/input/js0 to see values from TX. If no value can +be changed by TX "joystick", check output from /proc/interrupts. Value for +(usually irq7) parport must increase if TX is on. + + + +Technical details +================= + +Driver use interrupt from parport ACK input bit to measure pulse length +using hrtimers. + +Frame format: +Based on walkera WK-0701 PCM Format description by Shaul Eizikovich. +(downloaded from http://www.smartpropoplus.com/Docs/Walkera_Wk-0701_PCM.pdf) + +Signal pulses +------------- + +:: + + (ANALOG) + SYNC BIN OCT + +---------+ +------+ + | | | | + --+ +------+ +--- + +Frame +----- + +:: + + SYNC , BIN1, OCT1, BIN2, OCT2 ... BIN24, OCT24, BIN25, next frame SYNC .. + +pulse length +------------ + +:: + + Binary values: Analog octal values: + + 288 uS Binary 0 318 uS 000 + 438 uS Binary 1 398 uS 001 + 478 uS 010 + 558 uS 011 + 638 uS 100 + 1306 uS SYNC 718 uS 101 + 798 uS 110 + 878 uS 111 + +24 bin+oct values + 1 bin value = 24*4+1 bits = 97 bits + +(Warning, pulses on ACK are inverted by transistor, irq is raised up on sync +to bin change or octal value to bin change). + +Binary data representations +--------------------------- + +One binary and octal value can be grouped to nibble. 24 nibbles + one binary +values can be sampled between sync pulses. + +Values for first four channels (analog joystick values) can be found in +first 10 nibbles. Analog value is represented by one sign bit and 9 bit +absolute binary value. (10 bits per channel). Next nibble is checksum for +first ten nibbles. + +Next nibbles 12 .. 21 represents four channels (not all channels can be +directly controlled from TX). Binary representations are the same as in first +four channels. In nibbles 22 and 23 is a special magic number. Nibble 24 is +checksum for nibbles 12..23. + +After last octal value for nibble 24 and next sync pulse one additional +binary value can be sampled. This bit and magic number is not used in +software driver. Some details about this magic numbers can be found in +Walkera_Wk-0701_PCM.pdf. + +Checksum calculation +-------------------- + +Summary of octal values in nibbles must be same as octal value in checksum +nibble (only first 3 bits are used). Binary value for checksum nibble is +calculated by sum of binary values in checked nibbles + sum of octal values +in checked nibbles divided by 8. Only bit 0 of this sum is used. diff --git a/Documentation/input/devices/xpad.rst b/Documentation/input/devices/xpad.rst new file mode 100644 index 000000000..173c2acda --- /dev/null +++ b/Documentation/input/devices/xpad.rst @@ -0,0 +1,234 @@ +======================================================= +xpad - Linux USB driver for Xbox compatible controllers +======================================================= + +This driver exposes all first-party and third-party Xbox compatible +controllers. It has a long history and has enjoyed considerable usage +as Window's xinput library caused most PC games to focus on Xbox +controller compatibility. + +Due to backwards compatibility all buttons are reported as digital. +This only effects Original Xbox controllers. All later controller models +have only digital face buttons. + +Rumble is supported on some models of Xbox 360 controllers but not of +Original Xbox controllers nor on Xbox One controllers. As of writing +the Xbox One's rumble protocol has not been reverse engineered but in +the future could be supported. + + +Notes +===== + +The number of buttons/axes reported varies based on 3 things: + +- if you are using a known controller +- if you are using a known dance pad +- if using an unknown device (one not listed below), what you set in the + module configuration for "Map D-PAD to buttons rather than axes for unknown + pads" (module option dpad_to_buttons) + +If you set dpad_to_buttons to N and you are using an unknown device +the driver will map the directional pad to axes (X/Y). +If you said Y it will map the d-pad to buttons, which is needed for dance +style games to function correctly. The default is Y. + +dpad_to_buttons has no effect for known pads. A erroneous commit message +claimed dpad_to_buttons could be used to force behavior on known devices. +This is not true. Both dpad_to_buttons and triggers_to_buttons only affect +unknown controllers. + + +Normal Controllers +------------------ + +With a normal controller, the directional pad is mapped to its own X/Y axes. +The jstest-program from joystick-1.2.15 (jstest-version 2.1.0) will report 8 +axes and 10 buttons. + +All 8 axes work, though they all have the same range (-32768..32767) +and the zero-setting is not correct for the triggers (I don't know if that +is some limitation of jstest, since the input device setup should be fine. I +didn't have a look at jstest itself yet). + +All of the 10 buttons work (in digital mode). The six buttons on the +right side (A, B, X, Y, black, white) are said to be "analog" and +report their values as 8 bit unsigned, not sure what this is good for. + +I tested the controller with quake3, and configuration and +in game functionality were OK. However, I find it rather difficult to +play first person shooters with a pad. Your mileage may vary. + + +Xbox Dance Pads +--------------- + +When using a known dance pad, jstest will report 6 axes and 14 buttons. + +For dance style pads (like the redoctane pad) several changes +have been made. The old driver would map the d-pad to axes, resulting +in the driver being unable to report when the user was pressing both +left+right or up+down, making DDR style games unplayable. + +Known dance pads automatically map the d-pad to buttons and will work +correctly out of the box. + +If your dance pad is recognized by the driver but is using axes instead +of buttons, see section 0.3 - Unknown Controllers + +I've tested this with Stepmania, and it works quite well. + + +Unknown Controllers +------------------- + +If you have an unknown xbox controller, it should work just fine with +the default settings. + +HOWEVER if you have an unknown dance pad not listed below, it will not +work UNLESS you set "dpad_to_buttons" to 1 in the module configuration. + + +USB adapters +============ + +All generations of Xbox controllers speak USB over the wire. + +- Original Xbox controllers use a proprietary connector and require adapters. +- Wireless Xbox 360 controllers require a 'Xbox 360 Wireless Gaming Receiver + for Windows' +- Wired Xbox 360 controllers use standard USB connectors. +- Xbox One controllers can be wireless but speak Wi-Fi Direct and are not + yet supported. +- Xbox One controllers can be wired and use standard Micro-USB connectors. + + + +Original Xbox USB adapters +-------------------------- + +Using this driver with an Original Xbox controller requires an +adapter cable to break out the proprietary connector's pins to USB. +You can buy these online fairly cheap, or build your own. + +Such a cable is pretty easy to build. The Controller itself is a USB +compound device (a hub with three ports for two expansion slots and +the controller device) with the only difference in a nonstandard connector +(5 pins vs. 4 on standard USB 1.0 connectors). + +You just need to solder a USB connector onto the cable and keep the +yellow wire unconnected. The other pins have the same order on both +connectors so there is no magic to it. Detailed info on these matters +can be found on the net ([1]_, [2]_, [3]_). + +Thanks to the trip splitter found on the cable you don't even need to cut the +original one. You can buy an extension cable and cut that instead. That way, +you can still use the controller with your X-Box, if you have one ;) + + + +Driver Installation +=================== + +Once you have the adapter cable, if needed, and the controller connected +the xpad module should be auto loaded. To confirm you can cat +/sys/kernel/debug/usb/devices. There should be an entry like those: + +.. code-block:: none + :caption: dump from InterAct PowerPad Pro (Germany) + + T: Bus=01 Lev=03 Prnt=04 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0 + D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=32 #Cfgs= 1 + P: Vendor=05fd ProdID=107a Rev= 1.00 + C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA + I: If#= 0 Alt= 0 #EPs= 2 Cls=58(unk. ) Sub=42 Prot=00 Driver=(none) + E: Ad=81(I) Atr=03(Int.) MxPS= 32 Ivl= 10ms + E: Ad=02(O) Atr=03(Int.) MxPS= 32 Ivl= 10ms + +.. code-block:: none + :caption: dump from Redoctane Xbox Dance Pad (US) + + T: Bus=01 Lev=02 Prnt=09 Port=00 Cnt=01 Dev#= 10 Spd=12 MxCh= 0 + D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 + P: Vendor=0c12 ProdID=8809 Rev= 0.01 + S: Product=XBOX DDR + C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA + I: If#= 0 Alt= 0 #EPs= 2 Cls=58(unk. ) Sub=42 Prot=00 Driver=xpad + E: Ad=82(I) Atr=03(Int.) MxPS= 32 Ivl=4ms + E: Ad=02(O) Atr=03(Int.) MxPS= 32 Ivl=4ms + + +Supported Controllers +===================== + +For a full list of supported controllers and associated vendor and product +IDs see the xpad_device[] array\ [4]_. + +As of the historic version 0.0.6 (2006-10-10) the following devices +were supported:: + + original Microsoft XBOX controller (US), vendor=0x045e, product=0x0202 + smaller Microsoft XBOX controller (US), vendor=0x045e, product=0x0289 + original Microsoft XBOX controller (Japan), vendor=0x045e, product=0x0285 + InterAct PowerPad Pro (Germany), vendor=0x05fd, product=0x107a + RedOctane Xbox Dance Pad (US), vendor=0x0c12, product=0x8809 + +Unrecognized models of Xbox controllers should function as Generic +Xbox controllers. Unrecognized Dance Pad controllers require setting +the module option 'dpad_to_buttons'. + +If you have an unrecognized controller please see 0.3 - Unknown Controllers + + +Manual Testing +============== + +To test this driver's functionality you may use 'jstest'. + +For example:: + + > modprobe xpad + > modprobe joydev + > jstest /dev/js0 + +If you're using a normal controller, there should be a single line showing +18 inputs (8 axes, 10 buttons), and its values should change if you move +the sticks and push the buttons. If you're using a dance pad, it should +show 20 inputs (6 axes, 14 buttons). + +It works? Voila, you're done ;) + + + +Thanks +====== + +I have to thank ITO Takayuki for the detailed info on his site + http://euc.jp/periphs/xbox-controller.ja.html. + +His useful info and both the usb-skeleton as well as the iforce input driver +(Greg Kroah-Hartmann; Vojtech Pavlik) helped a lot in rapid prototyping +the basic functionality. + + + +References +========== + +.. [1] http://euc.jp/periphs/xbox-controller.ja.html (ITO Takayuki) +.. [2] http://xpad.xbox-scene.com/ +.. [3] http://www.markosweb.com/www/xboxhackz.com/ +.. [4] https://elixir.bootlin.com/linux/latest/ident/xpad_device + + +Historic Edits +============== + +2002-07-16 - Marko Friedemann <mfr@bmx-chemnitz.de> + - original doc + +2005-03-19 - Dominic Cerquetti <binary1230@yahoo.com> + - added stuff for dance pads, new d-pad->axes mappings + +Later changes may be viewed with +'git log --follow Documentation/input/devices/xpad.rst' diff --git a/Documentation/input/devices/yealink.rst b/Documentation/input/devices/yealink.rst new file mode 100644 index 000000000..bb5a1aafe --- /dev/null +++ b/Documentation/input/devices/yealink.rst @@ -0,0 +1,225 @@ +=============================================== +Driver documentation for yealink usb-p1k phones +=============================================== + +Status +====== + +The p1k is a relatively cheap usb 1.1 phone with: + + - keyboard full support, yealink.ko / input event API + - LCD full support, yealink.ko / sysfs API + - LED full support, yealink.ko / sysfs API + - dialtone full support, yealink.ko / sysfs API + - ringtone full support, yealink.ko / sysfs API + - audio playback full support, snd_usb_audio.ko / alsa API + - audio record full support, snd_usb_audio.ko / alsa API + +For vendor documentation see http://www.yealink.com + + +keyboard features +================= + +The current mapping in the kernel is provided by the map_p1k_to_key +function:: + + Physical USB-P1K button layout input events + + + up up + IN OUT left, right + down down + + pickup C hangup enter, backspace, escape + 1 2 3 1, 2, 3 + 4 5 6 4, 5, 6, + 7 8 9 7, 8, 9, + * 0 # *, 0, #, + +The "up" and "down" keys, are symbolised by arrows on the button. +The "pickup" and "hangup" keys are symbolised by a green and red phone +on the button. + + +LCD features +============ + +The LCD is divided and organised as a 3 line display:: + + |[] [][] [][] [][] in |[][] + |[] M [][] D [][] : [][] out |[][] + store + + NEW REP SU MO TU WE TH FR SA + + [] [] [] [] [] [] [] [] [] [] [] [] + [] [] [] [] [] [] [] [] [] [] [] [] + + + Line 1 Format (see below) : 18.e8.M8.88...188 + Icon names : M D : IN OUT STORE + Line 2 Format : ......... + Icon name : NEW REP SU MO TU WE TH FR SA + Line 3 Format : 888888888888 + + +Format description: + From a userspace perspective the world is separated into "digits" and "icons". + A digit can have a character set, an icon can only be ON or OFF. + + Format specifier:: + + '8' : Generic 7 segment digit with individual addressable segments + + Reduced capability 7 segment digit, when segments are hard wired together. + '1' : 2 segments digit only able to produce a 1. + 'e' : Most significant day of the month digit, + able to produce at least 1 2 3. + 'M' : Most significant minute digit, + able to produce at least 0 1 2 3 4 5. + + Icons or pictograms: + '.' : For example like AM, PM, SU, a 'dot' .. or other single segment + elements. + + +Driver usage +============ + +For userland the following interfaces are available using the sysfs interface:: + + /sys/.../ + line1 Read/Write, lcd line1 + line2 Read/Write, lcd line2 + line3 Read/Write, lcd line3 + + get_icons Read, returns a set of available icons. + hide_icon Write, hide the element by writing the icon name. + show_icon Write, display the element by writing the icon name. + + map_seg7 Read/Write, the 7 segments char set, common for all + yealink phones. (see map_to_7segment.h) + + ringtone Write, upload binary representation of a ringtone, + see yealink.c. status EXPERIMENTAL due to potential + races between async. and sync usb calls. + + +lineX +~~~~~ + +Reading /sys/../lineX will return the format string with its current value. + + Example:: + + cat ./line3 + 888888888888 + Linux Rocks! + +Writing to /sys/../lineX will set the corresponding LCD line. + + - Excess characters are ignored. + - If less characters are written than allowed, the remaining digits are + unchanged. + - The tab '\t'and '\n' char does not overwrite the original content. + - Writing a space to an icon will always hide its content. + + Example:: + + date +"%m.%e.%k:%M" | sed 's/^0/ /' > ./line1 + + Will update the LCD with the current date & time. + + +get_icons +~~~~~~~~~ + +Reading will return all available icon names and its current settings:: + + cat ./get_icons + on M + on D + on : + IN + OUT + STORE + NEW + REP + SU + MO + TU + WE + TH + FR + SA + LED + DIALTONE + RINGTONE + + +show/hide icons +~~~~~~~~~~~~~~~ + +Writing to these files will update the state of the icon. +Only one icon at a time can be updated. + +If an icon is also on a ./lineX the corresponding value is +updated with the first letter of the icon. + + Example - light up the store icon:: + + echo -n "STORE" > ./show_icon + + cat ./line1 + 18.e8.M8.88...188 + S + + Example - sound the ringtone for 10 seconds:: + + echo -n RINGTONE > /sys/..../show_icon + sleep 10 + echo -n RINGTONE > /sys/..../hide_icon + + +Sound features +============== + +Sound is supported by the ALSA driver: snd_usb_audio + +One 16-bit channel with sample and playback rates of 8000 Hz is the practical +limit of the device. + + Example - recording test:: + + arecord -v -d 10 -r 8000 -f S16_LE -t wav foobar.wav + + Example - playback test:: + + aplay foobar.wav + + +Troubleshooting +=============== + +:Q: Module yealink compiled and installed without any problem but phone + is not initialized and does not react to any actions. +:A: If you see something like: + hiddev0: USB HID v1.00 Device [Yealink Network Technology Ltd. VOIP USB Phone + in dmesg, it means that the hid driver has grabbed the device first. Try to + load module yealink before any other usb hid driver. Please see the + instructions provided by your distribution on module configuration. + +:Q: Phone is working now (displays version and accepts keypad input) but I can't + find the sysfs files. +:A: The sysfs files are located on the particular usb endpoint. On most + distributions you can do: "find /sys/ -name get_icons" for a hint. + + +Credits & Acknowledgments +========================= + + - Olivier Vandorpe, for starting the usbb2k-api project doing much of + the reverse engineering. + - Martin Diehl, for pointing out how to handle USB memory allocation. + - Dmitry Torokhov, for the numerous code reviews and suggestions. diff --git a/Documentation/input/event-codes.rst b/Documentation/input/event-codes.rst new file mode 100644 index 000000000..b4557462e --- /dev/null +++ b/Documentation/input/event-codes.rst @@ -0,0 +1,453 @@ +.. _input-event-codes: + +================= +Input event codes +================= + + +The input protocol uses a map of types and codes to express input device values +to userspace. This document describes the types and codes and how and when they +may be used. + +A single hardware event generates multiple input events. Each input event +contains the new value of a single data item. A special event type, EV_SYN, is +used to separate input events into packets of input data changes occurring at +the same moment in time. In the following, the term "event" refers to a single +input event encompassing a type, code, and value. + +The input protocol is a stateful protocol. Events are emitted only when values +of event codes have changed. However, the state is maintained within the Linux +input subsystem; drivers do not need to maintain the state and may attempt to +emit unchanged values without harm. Userspace may obtain the current state of +event code values using the EVIOCG* ioctls defined in linux/input.h. The event +reports supported by a device are also provided by sysfs in +class/input/event*/device/capabilities/, and the properties of a device are +provided in class/input/event*/device/properties. + +Event types +=========== + +Event types are groupings of codes under a logical input construct. Each +type has a set of applicable codes to be used in generating events. See the +Codes section for details on valid codes for each type. + +* EV_SYN: + + - Used as markers to separate events. Events may be separated in time or in + space, such as with the multitouch protocol. + +* EV_KEY: + + - Used to describe state changes of keyboards, buttons, or other key-like + devices. + +* EV_REL: + + - Used to describe relative axis value changes, e.g. moving the mouse 5 units + to the left. + +* EV_ABS: + + - Used to describe absolute axis value changes, e.g. describing the + coordinates of a touch on a touchscreen. + +* EV_MSC: + + - Used to describe miscellaneous input data that do not fit into other types. + +* EV_SW: + + - Used to describe binary state input switches. + +* EV_LED: + + - Used to turn LEDs on devices on and off. + +* EV_SND: + + - Used to output sound to devices. + +* EV_REP: + + - Used for autorepeating devices. + +* EV_FF: + + - Used to send force feedback commands to an input device. + +* EV_PWR: + + - A special type for power button and switch input. + +* EV_FF_STATUS: + + - Used to receive force feedback device status. + +Event codes +=========== + +Event codes define the precise type of event. + +EV_SYN +------ + +EV_SYN event values are undefined. Their usage is defined only by when they are +sent in the evdev event stream. + +* SYN_REPORT: + + - Used to synchronize and separate events into packets of input data changes + occurring at the same moment in time. For example, motion of a mouse may set + the REL_X and REL_Y values for one motion, then emit a SYN_REPORT. The next + motion will emit more REL_X and REL_Y values and send another SYN_REPORT. + +* SYN_CONFIG: + + - TBD + +* SYN_MT_REPORT: + + - Used to synchronize and separate touch events. See the + multi-touch-protocol.txt document for more information. + +* SYN_DROPPED: + + - Used to indicate buffer overrun in the evdev client's event queue. + Client should ignore all events up to and including next SYN_REPORT + event and query the device (using EVIOCG* ioctls) to obtain its + current state. + +EV_KEY +------ + +EV_KEY events take the form KEY_<name> or BTN_<name>. For example, KEY_A is used +to represent the 'A' key on a keyboard. When a key is depressed, an event with +the key's code is emitted with value 1. When the key is released, an event is +emitted with value 0. Some hardware send events when a key is repeated. These +events have a value of 2. In general, KEY_<name> is used for keyboard keys, and +BTN_<name> is used for other types of momentary switch events. + +A few EV_KEY codes have special meanings: + +* BTN_TOOL_<name>: + + - These codes are used in conjunction with input trackpads, tablets, and + touchscreens. These devices may be used with fingers, pens, or other tools. + When an event occurs and a tool is used, the corresponding BTN_TOOL_<name> + code should be set to a value of 1. When the tool is no longer interacting + with the input device, the BTN_TOOL_<name> code should be reset to 0. All + trackpads, tablets, and touchscreens should use at least one BTN_TOOL_<name> + code when events are generated. Likewise all trackpads, tablets, and + touchscreens should export only one BTN_TOOL_<name> at a time. To not break + existing userspace, it is recommended to not switch tool in one EV_SYN frame + but first emitting the old BTN_TOOL_<name> at 0, then emit one SYN_REPORT + and then set the new BTN_TOOL_<name> at 1. + +* BTN_TOUCH: + + BTN_TOUCH is used for touch contact. While an input tool is determined to be + within meaningful physical contact, the value of this property must be set + to 1. Meaningful physical contact may mean any contact, or it may mean + contact conditioned by an implementation defined property. For example, a + touchpad may set the value to 1 only when the touch pressure rises above a + certain value. BTN_TOUCH may be combined with BTN_TOOL_<name> codes. For + example, a pen tablet may set BTN_TOOL_PEN to 1 and BTN_TOUCH to 0 while the + pen is hovering over but not touching the tablet surface. + +Note: For appropriate function of the legacy mousedev emulation driver, +BTN_TOUCH must be the first evdev code emitted in a synchronization frame. + +Note: Historically a touch device with BTN_TOOL_FINGER and BTN_TOUCH was +interpreted as a touchpad by userspace, while a similar device without +BTN_TOOL_FINGER was interpreted as a touchscreen. For backwards compatibility +with current userspace it is recommended to follow this distinction. In the +future, this distinction will be deprecated and the device properties ioctl +EVIOCGPROP, defined in linux/input.h, will be used to convey the device type. + +* BTN_TOOL_FINGER, BTN_TOOL_DOUBLETAP, BTN_TOOL_TRIPLETAP, BTN_TOOL_QUADTAP: + + - These codes denote one, two, three, and four finger interaction on a + trackpad or touchscreen. For example, if the user uses two fingers and moves + them on the touchpad in an effort to scroll content on screen, + BTN_TOOL_DOUBLETAP should be set to value 1 for the duration of the motion. + Note that all BTN_TOOL_<name> codes and the BTN_TOUCH code are orthogonal in + purpose. A trackpad event generated by finger touches should generate events + for one code from each group. At most only one of these BTN_TOOL_<name> + codes should have a value of 1 during any synchronization frame. + +Note: Historically some drivers emitted multiple of the finger count codes with +a value of 1 in the same synchronization frame. This usage is deprecated. + +Note: In multitouch drivers, the input_mt_report_finger_count() function should +be used to emit these codes. Please see multi-touch-protocol.txt for details. + +EV_REL +------ + +EV_REL events describe relative changes in a property. For example, a mouse may +move to the left by a certain number of units, but its absolute position in +space is unknown. If the absolute position is known, EV_ABS codes should be used +instead of EV_REL codes. + +A few EV_REL codes have special meanings: + +* REL_WHEEL, REL_HWHEEL: + + - These codes are used for vertical and horizontal scroll wheels, + respectively. The value is the number of detents moved on the wheel, the + physical size of which varies by device. For high-resolution wheels + this may be an approximation based on the high-resolution scroll events, + see REL_WHEEL_HI_RES. These event codes are legacy codes and + REL_WHEEL_HI_RES and REL_HWHEEL_HI_RES should be preferred where + available. + +* REL_WHEEL_HI_RES, REL_HWHEEL_HI_RES: + + - High-resolution scroll wheel data. The accumulated value 120 represents + movement by one detent. For devices that do not provide high-resolution + scrolling, the value is always a multiple of 120. For devices with + high-resolution scrolling, the value may be a fraction of 120. + + If a vertical scroll wheel supports high-resolution scrolling, this code + will be emitted in addition to REL_WHEEL or REL_HWHEEL. The REL_WHEEL + and REL_HWHEEL may be an approximation based on the high-resolution + scroll events. There is no guarantee that the high-resolution data + is a multiple of 120 at the time of an emulated REL_WHEEL or REL_HWHEEL + event. + +EV_ABS +------ + +EV_ABS events describe absolute changes in a property. For example, a touchpad +may emit coordinates for a touch location. + +A few EV_ABS codes have special meanings: + +* ABS_DISTANCE: + + - Used to describe the distance of a tool from an interaction surface. This + event should only be emitted while the tool is hovering, meaning in close + proximity of the device and while the value of the BTN_TOUCH code is 0. If + the input device may be used freely in three dimensions, consider ABS_Z + instead. + - BTN_TOOL_<name> should be set to 1 when the tool comes into detectable + proximity and set to 0 when the tool leaves detectable proximity. + BTN_TOOL_<name> signals the type of tool that is currently detected by the + hardware and is otherwise independent of ABS_DISTANCE and/or BTN_TOUCH. + +* ABS_PROFILE: + + - Used to describe the state of a multi-value profile switch. An event is + emitted only when the selected profile changes, indicating the newly + selected profile value. + +* ABS_MT_<name>: + + - Used to describe multitouch input events. Please see + multi-touch-protocol.txt for details. + +* ABS_PRESSURE/ABS_MT_PRESSURE: + + - For touch devices, many devices converted contact size into pressure. + A finger flattens with pressure, causing a larger contact area and thus + pressure and contact size are directly related. This is not the case + for other devices, for example digitizers and touchpads with a true + pressure sensor ("pressure pads"). + + A device should set the resolution of the axis to indicate whether the + pressure is in measurable units. If the resolution is zero, the + pressure data is in arbitrary units. If the resolution is non-zero, the + pressure data is in units/gram. For example, a value of 10 with a + resolution of 1 represents 10 gram, a value of 10 with a resolution of + 1000 represents 10 microgram. + +EV_SW +----- + +EV_SW events describe stateful binary switches. For example, the SW_LID code is +used to denote when a laptop lid is closed. + +Upon binding to a device or resuming from suspend, a driver must report +the current switch state. This ensures that the device, kernel, and userspace +state is in sync. + +Upon resume, if the switch state is the same as before suspend, then the input +subsystem will filter out the duplicate switch state reports. The driver does +not need to keep the state of the switch at any time. + +EV_MSC +------ + +EV_MSC events are used for input and output events that do not fall under other +categories. + +A few EV_MSC codes have special meaning: + +* MSC_TIMESTAMP: + + - Used to report the number of microseconds since the last reset. This event + should be coded as an uint32 value, which is allowed to wrap around with + no special consequence. It is assumed that the time difference between two + consecutive events is reliable on a reasonable time scale (hours). + A reset to zero can happen, in which case the time since the last event is + unknown. If the device does not provide this information, the driver must + not provide it to user space. + +EV_LED +------ + +EV_LED events are used for input and output to set and query the state of +various LEDs on devices. + +EV_REP +------ + +EV_REP events are used for specifying autorepeating events. + +EV_SND +------ + +EV_SND events are used for sending sound commands to simple sound output +devices. + +EV_FF +----- + +EV_FF events are used to initialize a force feedback capable device and to cause +such device to feedback. + +EV_PWR +------ + +EV_PWR events are a special type of event used specifically for power +management. Its usage is not well defined. To be addressed later. + +Device properties +================= + +Normally, userspace sets up an input device based on the data it emits, +i.e., the event types. In the case of two devices emitting the same event +types, additional information can be provided in the form of device +properties. + +INPUT_PROP_DIRECT + INPUT_PROP_POINTER +-------------------------------------- + +The INPUT_PROP_DIRECT property indicates that device coordinates should be +directly mapped to screen coordinates (not taking into account trivial +transformations, such as scaling, flipping and rotating). Non-direct input +devices require non-trivial transformation, such as absolute to relative +transformation for touchpads. Typical direct input devices: touchscreens, +drawing tablets; non-direct devices: touchpads, mice. + +The INPUT_PROP_POINTER property indicates that the device is not transposed +on the screen and thus requires use of an on-screen pointer to trace user's +movements. Typical pointer devices: touchpads, tablets, mice; non-pointer +device: touchscreen. + +If neither INPUT_PROP_DIRECT or INPUT_PROP_POINTER are set, the property is +considered undefined and the device type should be deduced in the +traditional way, using emitted event types. + +INPUT_PROP_BUTTONPAD +-------------------- + +For touchpads where the button is placed beneath the surface, such that +pressing down on the pad causes a button click, this property should be +set. Common in Clickpad notebooks and Macbooks from 2009 and onwards. + +Originally, the buttonpad property was coded into the bcm5974 driver +version field under the name integrated button. For backwards +compatibility, both methods need to be checked in userspace. + +INPUT_PROP_SEMI_MT +------------------ + +Some touchpads, most common between 2008 and 2011, can detect the presence +of multiple contacts without resolving the individual positions; only the +number of contacts and a rectangular shape is known. For such +touchpads, the SEMI_MT property should be set. + +Depending on the device, the rectangle may enclose all touches, like a +bounding box, or just some of them, for instance the two most recent +touches. The diversity makes the rectangle of limited use, but some +gestures can normally be extracted from it. + +If INPUT_PROP_SEMI_MT is not set, the device is assumed to be a true MT +device. + +INPUT_PROP_TOPBUTTONPAD +----------------------- + +Some laptops, most notably the Lenovo 40 series provide a trackstick +device but do not have physical buttons associated with the trackstick +device. Instead, the top area of the touchpad is marked to show +visual/haptic areas for left, middle, right buttons intended to be used +with the trackstick. + +If INPUT_PROP_TOPBUTTONPAD is set, userspace should emulate buttons +accordingly. This property does not affect kernel behavior. +The kernel does not provide button emulation for such devices but treats +them as any other INPUT_PROP_BUTTONPAD device. + +INPUT_PROP_ACCELEROMETER +------------------------ + +Directional axes on this device (absolute and/or relative x, y, z) represent +accelerometer data. Some devices also report gyroscope data, which devices +can report through the rotational axes (absolute and/or relative rx, ry, rz). + +All other axes retain their meaning. A device must not mix +regular directional axes and accelerometer axes on the same event node. + +Guidelines +========== + +The guidelines below ensure proper single-touch and multi-finger functionality. +For multi-touch functionality, see the multi-touch-protocol.rst document for +more information. + +Mice +---- + +REL_{X,Y} must be reported when the mouse moves. BTN_LEFT must be used to report +the primary button press. BTN_{MIDDLE,RIGHT,4,5,etc.} should be used to report +further buttons of the device. REL_WHEEL and REL_HWHEEL should be used to report +scroll wheel events where available. + +Touchscreens +------------ + +ABS_{X,Y} must be reported with the location of the touch. BTN_TOUCH must be +used to report when a touch is active on the screen. +BTN_{MOUSE,LEFT,MIDDLE,RIGHT} must not be reported as the result of touch +contact. BTN_TOOL_<name> events should be reported where possible. + +For new hardware, INPUT_PROP_DIRECT should be set. + +Trackpads +--------- + +Legacy trackpads that only provide relative position information must report +events like mice described above. + +Trackpads that provide absolute touch position must report ABS_{X,Y} for the +location of the touch. BTN_TOUCH should be used to report when a touch is active +on the trackpad. Where multi-finger support is available, BTN_TOOL_<name> should +be used to report the number of touches active on the trackpad. + +For new hardware, INPUT_PROP_POINTER should be set. + +Tablets +------- + +BTN_TOOL_<name> events must be reported when a stylus or other tool is active on +the tablet. ABS_{X,Y} must be reported with the location of the tool. BTN_TOUCH +should be used to report when the tool is in contact with the tablet. +BTN_{STYLUS,STYLUS2} should be used to report buttons on the tool itself. Any +button may be used for buttons on the tablet except BTN_{MOUSE,LEFT}. +BTN_{0,1,2,etc} are good generic codes for unlabeled buttons. Do not use +meaningful buttons, like BTN_FORWARD, unless the button is labeled for that +purpose on the device. + +For new hardware, both INPUT_PROP_DIRECT and INPUT_PROP_POINTER should be set. diff --git a/Documentation/input/ff.rst b/Documentation/input/ff.rst new file mode 100644 index 000000000..5a1da42c3 --- /dev/null +++ b/Documentation/input/ff.rst @@ -0,0 +1,265 @@ +======================== +Force feedback for Linux +======================== + +:Author: Johann Deneux <johann.deneux@gmail.com> on 2001/04/22. +:Updated: Anssi Hannula <anssi.hannula@gmail.com> on 2006/04/09. + +You may redistribute this file. Please remember to include shape.svg and +interactive.svg as well. + +Introduction +~~~~~~~~~~~~ + +This document describes how to use force feedback devices under Linux. The +goal is not to support these devices as if they were simple input-only devices +(as it is already the case), but to really enable the rendering of force +effects. +This document only describes the force feedback part of the Linux input +interface. Please read joydev/joystick.rst and input.rst before reading further +this document. + +Instructions to the user +~~~~~~~~~~~~~~~~~~~~~~~~ + +To enable force feedback, you have to: + +1. have your kernel configured with evdev and a driver that supports your + device. +2. make sure evdev module is loaded and /dev/input/event* device files are + created. + +Before you start, let me WARN you that some devices shake violently during the +initialisation phase. This happens for example with my "AVB Top Shot Pegasus". +To stop this annoying behaviour, move your joystick to its limits. Anyway, you +should keep a hand on your device, in order to avoid it to break down if +something goes wrong. + +If you have a serial iforce device, you need to start inputattach. See +joydev/joystick.rst for details. + +Does it work ? +-------------- + +There is an utility called fftest that will allow you to test the driver:: + + % fftest /dev/input/eventXX + +Instructions to the developer +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +All interactions are done using the event API. That is, you can use ioctl() +and write() on /dev/input/eventXX. +This information is subject to change. + +Querying device capabilities +---------------------------- + +:: + + #include <linux/input.h> + #include <sys/ioctl.h> + + #define BITS_TO_LONGS(x) \ + (((x) + 8 * sizeof (unsigned long) - 1) / (8 * sizeof (unsigned long))) + unsigned long features[BITS_TO_LONGS(FF_CNT)]; + int ioctl(int file_descriptor, int request, unsigned long *features); + +"request" must be EVIOCGBIT(EV_FF, size of features array in bytes ) + +Returns the features supported by the device. features is a bitfield with the +following bits: + +- FF_CONSTANT can render constant force effects +- FF_PERIODIC can render periodic effects with the following waveforms: + + - FF_SQUARE square waveform + - FF_TRIANGLE triangle waveform + - FF_SINE sine waveform + - FF_SAW_UP sawtooth up waveform + - FF_SAW_DOWN sawtooth down waveform + - FF_CUSTOM custom waveform + +- FF_RAMP can render ramp effects +- FF_SPRING can simulate the presence of a spring +- FF_FRICTION can simulate friction +- FF_DAMPER can simulate damper effects +- FF_RUMBLE rumble effects +- FF_INERTIA can simulate inertia +- FF_GAIN gain is adjustable +- FF_AUTOCENTER autocenter is adjustable + +.. note:: + + - In most cases you should use FF_PERIODIC instead of FF_RUMBLE. All + devices that support FF_RUMBLE support FF_PERIODIC (square, triangle, + sine) and the other way around. + + - The exact syntax FF_CUSTOM is undefined for the time being as no driver + supports it yet. + +:: + + int ioctl(int fd, EVIOCGEFFECTS, int *n); + +Returns the number of effects the device can keep in its memory. + +Uploading effects to the device +------------------------------- + +:: + + #include <linux/input.h> + #include <sys/ioctl.h> + + int ioctl(int file_descriptor, int request, struct ff_effect *effect); + +"request" must be EVIOCSFF. + +"effect" points to a structure describing the effect to upload. The effect is +uploaded, but not played. +The content of effect may be modified. In particular, its field "id" is set +to the unique id assigned by the driver. This data is required for performing +some operations (removing an effect, controlling the playback). +The "id" field must be set to -1 by the user in order to tell the driver to +allocate a new effect. + +Effects are file descriptor specific. + +See <uapi/linux/input.h> for a description of the ff_effect struct. You +should also find help in a few sketches, contained in files shape.svg +and interactive.svg: + +.. kernel-figure:: shape.svg + + Shape + +.. kernel-figure:: interactive.svg + + Interactive + + +Removing an effect from the device +---------------------------------- + +:: + + int ioctl(int fd, EVIOCRMFF, effect.id); + +This makes room for new effects in the device's memory. Note that this also +stops the effect if it was playing. + +Controlling the playback of effects +----------------------------------- + +Control of playing is done with write(). Below is an example: + +:: + + #include <linux/input.h> + #include <unistd.h> + + struct input_event play; + struct input_event stop; + struct ff_effect effect; + int fd; + ... + fd = open("/dev/input/eventXX", O_RDWR); + ... + /* Play three times */ + play.type = EV_FF; + play.code = effect.id; + play.value = 3; + + write(fd, (const void*) &play, sizeof(play)); + ... + /* Stop an effect */ + stop.type = EV_FF; + stop.code = effect.id; + stop.value = 0; + + write(fd, (const void*) &stop, sizeof(stop)); + +Setting the gain +---------------- + +Not all devices have the same strength. Therefore, users should set a gain +factor depending on how strong they want effects to be. This setting is +persistent across access to the driver. + +:: + + /* Set the gain of the device + int gain; /* between 0 and 100 */ + struct input_event ie; /* structure used to communicate with the driver */ + + ie.type = EV_FF; + ie.code = FF_GAIN; + ie.value = 0xFFFFUL * gain / 100; + + if (write(fd, &ie, sizeof(ie)) == -1) + perror("set gain"); + +Enabling/Disabling autocenter +----------------------------- + +The autocenter feature quite disturbs the rendering of effects in my opinion, +and I think it should be an effect, which computation depends on the game +type. But you can enable it if you want. + +:: + + int autocenter; /* between 0 and 100 */ + struct input_event ie; + + ie.type = EV_FF; + ie.code = FF_AUTOCENTER; + ie.value = 0xFFFFUL * autocenter / 100; + + if (write(fd, &ie, sizeof(ie)) == -1) + perror("set auto-center"); + +A value of 0 means "no auto-center". + +Dynamic update of an effect +--------------------------- + +Proceed as if you wanted to upload a new effect, except that instead of +setting the id field to -1, you set it to the wanted effect id. +Normally, the effect is not stopped and restarted. However, depending on the +type of device, not all parameters can be dynamically updated. For example, +the direction of an effect cannot be updated with iforce devices. In this +case, the driver stops the effect, up-load it, and restart it. + +Therefore it is recommended to dynamically change direction while the effect +is playing only when it is ok to restart the effect with a replay count of 1. + +Information about the status of effects +--------------------------------------- + +Every time the status of an effect is changed, an event is sent. The values +and meanings of the fields of the event are as follows:: + + struct input_event { + /* When the status of the effect changed */ + struct timeval time; + + /* Set to EV_FF_STATUS */ + unsigned short type; + + /* Contains the id of the effect */ + unsigned short code; + + /* Indicates the status */ + unsigned int value; + }; + + FF_STATUS_STOPPED The effect stopped playing + FF_STATUS_PLAYING The effect started to play + +.. note:: + + - Status feedback is only supported by iforce driver. If you have + a really good reason to use this, please contact + linux-joystick@atrey.karlin.mff.cuni.cz or anssi.hannula@gmail.com + so that support for it can be added to the rest of the drivers. diff --git a/Documentation/input/gamepad.rst b/Documentation/input/gamepad.rst new file mode 100644 index 000000000..71019de46 --- /dev/null +++ b/Documentation/input/gamepad.rst @@ -0,0 +1,197 @@ +--------------------------- +Linux Gamepad Specification +--------------------------- + +:Author: 2013 by David Herrmann <dh.herrmann@gmail.com> + + +Introduction +~~~~~~~~~~~~ +Linux provides many different input drivers for gamepad hardware. To avoid +having user-space deal with different button-mappings for each gamepad, this +document defines how gamepads are supposed to report their data. + +Geometry +~~~~~~~~ +As "gamepad" we define devices which roughly look like this:: + + ____________________________ __ + / [__ZL__] [__ZR__] \ | + / [__ TL __] [__ TR __] \ | Front Triggers + __/________________________________\__ __| + / _ \ | + / /\ __ (N) \ | + / || __ |MO| __ _ _ \ | Main Pad + | <===DP===> |SE| |ST| (W) -|- (E) | | + \ || ___ ___ _ / | + /\ \/ / \ / \ (S) /\ __| + / \________ | LS | ____ | RS | ________/ \ | + | / \ \___/ / \ \___/ / \ | | Control Sticks + | / \_____/ \_____/ \ | __| + | / \ | + \_____/ \_____/ + + |________|______| |______|___________| + D-Pad Left Right Action Pad + Stick Stick + + |_____________| + Menu Pad + +Most gamepads have the following features: + + - Action-Pad + 4 buttons in diamonds-shape (on the right side). The buttons are + differently labeled on most devices so we define them as NORTH, + SOUTH, WEST and EAST. + - D-Pad (Direction-pad) + 4 buttons (on the left side) that point up, down, left and right. + - Menu-Pad + Different constellations, but most-times 2 buttons: SELECT - START + Furthermore, many gamepads have a fancy branded button that is used as + special system-button. It often looks different to the other buttons and + is used to pop up system-menus or system-settings. + - Analog-Sticks + Analog-sticks provide freely moveable sticks to control directions. Not + all devices have both or any, but they are present at most times. + Analog-sticks may also provide a digital button if you press them. + - Triggers + Triggers are located on the upper-side of the pad in vertical direction. + Not all devices provide them, but the upper buttons are normally named + Left- and Right-Triggers, the lower buttons Z-Left and Z-Right. + - Rumble + Many devices provide force-feedback features. But are mostly just + simple rumble motors. + +Detection +~~~~~~~~~ + +All gamepads that follow the protocol described here map BTN_GAMEPAD. This is +an alias for BTN_SOUTH/BTN_A. It can be used to identify a gamepad as such. +However, not all gamepads provide all features, so you need to test for all +features that you need, first. How each feature is mapped is described below. + +Legacy drivers often don't comply to these rules. As we cannot change them +for backwards-compatibility reasons, you need to provide fixup mappings in +user-space yourself. Some of them might also provide module-options that +change the mappings so you can advise users to set these. + +All new gamepads are supposed to comply with this mapping. Please report any +bugs, if they don't. + +There are a lot of less-featured/less-powerful devices out there, which re-use +the buttons from this protocol. However, they try to do this in a compatible +fashion. For example, the "Nintendo Wii Nunchuk" provides two trigger buttons +and one analog stick. It reports them as if it were a gamepad with only one +analog stick and two trigger buttons on the right side. +But that means, that if you only support "real" gamepads, you must test +devices for _all_ reported events that you need. Otherwise, you will also get +devices that report a small subset of the events. + +No other devices, that do not look/feel like a gamepad, shall report these +events. + +Events +~~~~~~ + +Gamepads report the following events: + +- Action-Pad: + + Every gamepad device has at least 2 action buttons. This means, that every + device reports BTN_SOUTH (which BTN_GAMEPAD is an alias for). Regardless + of the labels on the buttons, the codes are sent according to the + physical position of the buttons. + + Please note that 2- and 3-button pads are fairly rare and old. You might + want to filter gamepads that do not report all four. + + - 2-Button Pad: + + If only 2 action-buttons are present, they are reported as BTN_SOUTH and + BTN_EAST. For vertical layouts, the upper button is BTN_EAST. For + horizontal layouts, the button more on the right is BTN_EAST. + + - 3-Button Pad: + + If only 3 action-buttons are present, they are reported as (from left + to right): BTN_WEST, BTN_SOUTH, BTN_EAST + If the buttons are aligned perfectly vertically, they are reported as + (from top down): BTN_WEST, BTN_SOUTH, BTN_EAST + + - 4-Button Pad: + + If all 4 action-buttons are present, they can be aligned in two + different formations. If diamond-shaped, they are reported as BTN_NORTH, + BTN_WEST, BTN_SOUTH, BTN_EAST according to their physical location. + If rectangular-shaped, the upper-left button is BTN_NORTH, lower-left + is BTN_WEST, lower-right is BTN_SOUTH and upper-right is BTN_EAST. + +- D-Pad: + + Every gamepad provides a D-Pad with four directions: Up, Down, Left, Right + Some of these are available as digital buttons, some as analog buttons. Some + may even report both. The kernel does not convert between these so + applications should support both and choose what is more appropriate if + both are reported. + + - Digital buttons are reported as: + + BTN_DPAD_* + + - Analog buttons are reported as: + + ABS_HAT0X and ABS_HAT0Y + + (for ABS values negative is left/up, positive is right/down) + +- Analog-Sticks: + + The left analog-stick is reported as ABS_X, ABS_Y. The right analog stick is + reported as ABS_RX, ABS_RY. Zero, one or two sticks may be present. + If analog-sticks provide digital buttons, they are mapped accordingly as + BTN_THUMBL (first/left) and BTN_THUMBR (second/right). + + (for ABS values negative is left/up, positive is right/down) + +- Triggers: + + Trigger buttons can be available as digital or analog buttons or both. User- + space must correctly deal with any situation and choose the most appropriate + mode. + + Upper trigger buttons are reported as BTN_TR or ABS_HAT1X (right) and BTN_TL + or ABS_HAT1Y (left). Lower trigger buttons are reported as BTN_TR2 or + ABS_HAT2X (right/ZR) and BTN_TL2 or ABS_HAT2Y (left/ZL). + + If only one trigger-button combination is present (upper+lower), they are + reported as "right" triggers (BTN_TR/ABS_HAT1X). + + (ABS trigger values start at 0, pressure is reported as positive values) + +- Menu-Pad: + + Menu buttons are always digital and are mapped according to their location + instead of their labels. That is: + + - 1-button Pad: + + Mapped as BTN_START + + - 2-button Pad: + + Left button mapped as BTN_SELECT, right button mapped as BTN_START + + Many pads also have a third button which is branded or has a special symbol + and meaning. Such buttons are mapped as BTN_MODE. Examples are the Nintendo + "HOME" button, the XBox "X"-button or Sony "PS" button. + +- Rumble: + + Rumble is advertised as FF_RUMBLE. + +- Profile: + + Some pads provide a multi-value profile selection switch. An example is the + XBox Adaptive and the XBox Elite 2 controllers. When the active profile is + switched, its newly selected value is emitted as an ABS_PROFILE event. diff --git a/Documentation/input/gameport-programming.rst b/Documentation/input/gameport-programming.rst new file mode 100644 index 000000000..7d7063ad0 --- /dev/null +++ b/Documentation/input/gameport-programming.rst @@ -0,0 +1,233 @@ +~~~~~~~~~~~~~~~~~~~~~~~~~~~~ +Programming gameport drivers +~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +A basic classic gameport +~~~~~~~~~~~~~~~~~~~~~~~~ + +If the gameport doesn't provide more than the inb()/outb() functionality, +the code needed to register it with the joystick drivers is simple:: + + struct gameport gameport; + + gameport.io = MY_IO_ADDRESS; + gameport_register_port(&gameport); + +Make sure struct gameport is initialized to 0 in all other fields. The +gameport generic code will take care of the rest. + +If your hardware supports more than one io address, and your driver can +choose which one to program the hardware to, starting from the more exotic +addresses is preferred, because the likelihood of clashing with the standard +0x201 address is smaller. + +E.g. if your driver supports addresses 0x200, 0x208, 0x210 and 0x218, then +0x218 would be the address of first choice. + +If your hardware supports a gameport address that is not mapped to ISA io +space (is above 0x1000), use that one, and don't map the ISA mirror. + +Also, always request_region() on the whole io space occupied by the +gameport. Although only one ioport is really used, the gameport usually +occupies from one to sixteen addresses in the io space. + +Please also consider enabling the gameport on the card in the ->open() +callback if the io is mapped to ISA space - this way it'll occupy the io +space only when something really is using it. Disable it again in the +->close() callback. You also can select the io address in the ->open() +callback, so that it doesn't fail if some of the possible addresses are +already occupied by other gameports. + +Memory mapped gameport +~~~~~~~~~~~~~~~~~~~~~~ + +When a gameport can be accessed through MMIO, this way is preferred, because +it is faster, allowing more reads per second. Registering such a gameport +isn't as easy as a basic IO one, but not so much complex:: + + struct gameport gameport; + + void my_trigger(struct gameport *gameport) + { + my_mmio = 0xff; + } + + unsigned char my_read(struct gameport *gameport) + { + return my_mmio; + } + + gameport.read = my_read; + gameport.trigger = my_trigger; + gameport_register_port(&gameport); + +.. _gameport_pgm_cooked_mode: + +Cooked mode gameport +~~~~~~~~~~~~~~~~~~~~ + +There are gameports that can report the axis values as numbers, that means +the driver doesn't have to measure them the old way - an ADC is built into +the gameport. To register a cooked gameport:: + + struct gameport gameport; + + int my_cooked_read(struct gameport *gameport, int *axes, int *buttons) + { + int i; + + for (i = 0; i < 4; i++) + axes[i] = my_mmio[i]; + buttons[0] = my_mmio[4]; + } + + int my_open(struct gameport *gameport, int mode) + { + return -(mode != GAMEPORT_MODE_COOKED); + } + + gameport.cooked_read = my_cooked_read; + gameport.open = my_open; + gameport.fuzz = 8; + gameport_register_port(&gameport); + +The only confusing thing here is the fuzz value. Best determined by +experimentation, it is the amount of noise in the ADC data. Perfect +gameports can set this to zero, most common have fuzz between 8 and 32. +See analog.c and input.c for handling of fuzz - the fuzz value determines +the size of a gaussian filter window that is used to eliminate the noise +in the data. + +More complex gameports +~~~~~~~~~~~~~~~~~~~~~~ + +Gameports can support both raw and cooked modes. In that case combine either +examples 1+2 or 1+3. Gameports can support internal calibration - see below, +and also lightning.c and analog.c on how that works. If your driver supports +more than one gameport instance simultaneously, use the ->private member of +the gameport struct to point to your data. + +Unregistering a gameport +~~~~~~~~~~~~~~~~~~~~~~~~ + +Simple:: + + gameport_unregister_port(&gameport); + +The gameport structure +~~~~~~~~~~~~~~~~~~~~~~ + +:: + + struct gameport { + + void *port_data; + +A private pointer for free use in the gameport driver. (Not the joystick +driver!) + +:: + + char name[32]; + +Driver's name as set by driver calling gameport_set_name(). Informational +purpose only. + +:: + + char phys[32]; + +gameport's physical name/description as set by driver calling gameport_set_phys(). +Informational purpose only. + +:: + + int io; + +I/O address for use with raw mode. You have to either set this, or ->read() +to some value if your gameport supports raw mode. + +:: + + int speed; + +Raw mode speed of the gameport reads in thousands of reads per second. + +:: + + int fuzz; + +If the gameport supports cooked mode, this should be set to a value that +represents the amount of noise in the data. See +:ref:`gameport_pgm_cooked_mode`. + +:: + + void (*trigger)(struct gameport *); + +Trigger. This function should trigger the ns558 oneshots. If set to NULL, +outb(0xff, io) will be used. + +:: + + unsigned char (*read)(struct gameport *); + +Read the buttons and ns558 oneshot bits. If set to NULL, inb(io) will be +used instead. + +:: + + int (*cooked_read)(struct gameport *, int *axes, int *buttons); + +If the gameport supports cooked mode, it should point this to its cooked +read function. It should fill axes[0..3] with four values of the joystick axes +and buttons[0] with four bits representing the buttons. + +:: + + int (*calibrate)(struct gameport *, int *axes, int *max); + +Function for calibrating the ADC hardware. When called, axes[0..3] should be +pre-filled by cooked data by the caller, max[0..3] should be pre-filled with +expected maximums for each axis. The calibrate() function should set the +sensitivity of the ADC hardware so that the maximums fit in its range and +recompute the axes[] values to match the new sensitivity or re-read them from +the hardware so that they give valid values. + +:: + + int (*open)(struct gameport *, int mode); + +Open() serves two purposes. First a driver either opens the port in raw or +in cooked mode, the open() callback can decide which modes are supported. +Second, resource allocation can happen here. The port can also be enabled +here. Prior to this call, other fields of the gameport struct (namely the io +member) need not to be valid. + +:: + + void (*close)(struct gameport *); + +Close() should free the resources allocated by open, possibly disabling the +gameport. + +:: + + struct timer_list poll_timer; + unsigned int poll_interval; /* in msecs */ + spinlock_t timer_lock; + unsigned int poll_cnt; + void (*poll_handler)(struct gameport *); + struct gameport *parent, *child; + struct gameport_driver *drv; + struct mutex drv_mutex; /* protects serio->drv so attributes can pin driver */ + struct device dev; + struct list_head node; + +For internal use by the gameport layer. + +:: + + }; + +Enjoy! diff --git a/Documentation/input/index.rst b/Documentation/input/index.rst new file mode 100644 index 000000000..9888f5cbf --- /dev/null +++ b/Documentation/input/index.rst @@ -0,0 +1,19 @@ +============================= +The Linux Input Documentation +============================= + +Contents: + +.. toctree:: + :maxdepth: 2 + + input_uapi + input_kapi + devices/index + +.. only:: subproject and html + + Indices + ======= + + * :ref:`genindex` diff --git a/Documentation/input/input-programming.rst b/Documentation/input/input-programming.rst new file mode 100644 index 000000000..c9264814c --- /dev/null +++ b/Documentation/input/input-programming.rst @@ -0,0 +1,348 @@ +=============================== +Creating an input device driver +=============================== + +The simplest example +~~~~~~~~~~~~~~~~~~~~ + +Here comes a very simple example of an input device driver. The device has +just one button and the button is accessible at i/o port BUTTON_PORT. When +pressed or released a BUTTON_IRQ happens. The driver could look like:: + + #include <linux/input.h> + #include <linux/module.h> + #include <linux/init.h> + + #include <asm/irq.h> + #include <asm/io.h> + + static struct input_dev *button_dev; + + static irqreturn_t button_interrupt(int irq, void *dummy) + { + input_report_key(button_dev, BTN_0, inb(BUTTON_PORT) & 1); + input_sync(button_dev); + return IRQ_HANDLED; + } + + static int __init button_init(void) + { + int error; + + if (request_irq(BUTTON_IRQ, button_interrupt, 0, "button", NULL)) { + printk(KERN_ERR "button.c: Can't allocate irq %d\n", button_irq); + return -EBUSY; + } + + button_dev = input_allocate_device(); + if (!button_dev) { + printk(KERN_ERR "button.c: Not enough memory\n"); + error = -ENOMEM; + goto err_free_irq; + } + + button_dev->evbit[0] = BIT_MASK(EV_KEY); + button_dev->keybit[BIT_WORD(BTN_0)] = BIT_MASK(BTN_0); + + error = input_register_device(button_dev); + if (error) { + printk(KERN_ERR "button.c: Failed to register device\n"); + goto err_free_dev; + } + + return 0; + + err_free_dev: + input_free_device(button_dev); + err_free_irq: + free_irq(BUTTON_IRQ, button_interrupt); + return error; + } + + static void __exit button_exit(void) + { + input_unregister_device(button_dev); + free_irq(BUTTON_IRQ, button_interrupt); + } + + module_init(button_init); + module_exit(button_exit); + +What the example does +~~~~~~~~~~~~~~~~~~~~~ + +First it has to include the <linux/input.h> file, which interfaces to the +input subsystem. This provides all the definitions needed. + +In the _init function, which is called either upon module load or when +booting the kernel, it grabs the required resources (it should also check +for the presence of the device). + +Then it allocates a new input device structure with input_allocate_device() +and sets up input bitfields. This way the device driver tells the other +parts of the input systems what it is - what events can be generated or +accepted by this input device. Our example device can only generate EV_KEY +type events, and from those only BTN_0 event code. Thus we only set these +two bits. We could have used:: + + set_bit(EV_KEY, button_dev->evbit); + set_bit(BTN_0, button_dev->keybit); + +as well, but with more than single bits the first approach tends to be +shorter. + +Then the example driver registers the input device structure by calling:: + + input_register_device(button_dev); + +This adds the button_dev structure to linked lists of the input driver and +calls device handler modules _connect functions to tell them a new input +device has appeared. input_register_device() may sleep and therefore must +not be called from an interrupt or with a spinlock held. + +While in use, the only used function of the driver is:: + + button_interrupt() + +which upon every interrupt from the button checks its state and reports it +via the:: + + input_report_key() + +call to the input system. There is no need to check whether the interrupt +routine isn't reporting two same value events (press, press for example) to +the input system, because the input_report_* functions check that +themselves. + +Then there is the:: + + input_sync() + +call to tell those who receive the events that we've sent a complete report. +This doesn't seem important in the one button case, but is quite important +for example for mouse movement, where you don't want the X and Y values +to be interpreted separately, because that'd result in a different movement. + +dev->open() and dev->close() +~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +In case the driver has to repeatedly poll the device, because it doesn't +have an interrupt coming from it and the polling is too expensive to be done +all the time, or if the device uses a valuable resource (e.g. interrupt), it +can use the open and close callback to know when it can stop polling or +release the interrupt and when it must resume polling or grab the interrupt +again. To do that, we would add this to our example driver:: + + static int button_open(struct input_dev *dev) + { + if (request_irq(BUTTON_IRQ, button_interrupt, 0, "button", NULL)) { + printk(KERN_ERR "button.c: Can't allocate irq %d\n", button_irq); + return -EBUSY; + } + + return 0; + } + + static void button_close(struct input_dev *dev) + { + free_irq(IRQ_AMIGA_VERTB, button_interrupt); + } + + static int __init button_init(void) + { + ... + button_dev->open = button_open; + button_dev->close = button_close; + ... + } + +Note that input core keeps track of number of users for the device and +makes sure that dev->open() is called only when the first user connects +to the device and that dev->close() is called when the very last user +disconnects. Calls to both callbacks are serialized. + +The open() callback should return a 0 in case of success or any non-zero value +in case of failure. The close() callback (which is void) must always succeed. + +Inhibiting input devices +~~~~~~~~~~~~~~~~~~~~~~~~ + +Inhibiting a device means ignoring input events from it. As such it is about +maintaining relationships with input handlers - either already existing +relationships, or relationships to be established while the device is in +inhibited state. + +If a device is inhibited, no input handler will receive events from it. + +The fact that nobody wants events from the device is exploited further, by +calling device's close() (if there are users) and open() (if there are users) on +inhibit and uninhibit operations, respectively. Indeed, the meaning of close() +is to stop providing events to the input core and that of open() is to start +providing events to the input core. + +Calling the device's close() method on inhibit (if there are users) allows the +driver to save power. Either by directly powering down the device or by +releasing the runtime-PM reference it got in open() when the driver is using +runtime-PM. + +Inhibiting and uninhibiting are orthogonal to opening and closing the device by +input handlers. Userspace might want to inhibit a device in anticipation before +any handler is positively matched against it. + +Inhibiting and uninhibiting are orthogonal to device's being a wakeup source, +too. Being a wakeup source plays a role when the system is sleeping, not when +the system is operating. How drivers should program their interaction between +inhibiting, sleeping and being a wakeup source is driver-specific. + +Taking the analogy with the network devices - bringing a network interface down +doesn't mean that it should be impossible be wake the system up on LAN through +this interface. So, there may be input drivers which should be considered wakeup +sources even when inhibited. Actually, in many I2C input devices their interrupt +is declared a wakeup interrupt and its handling happens in driver's core, which +is not aware of input-specific inhibit (nor should it be). Composite devices +containing several interfaces can be inhibited on a per-interface basis and e.g. +inhibiting one interface shouldn't affect the device's capability of being a +wakeup source. + +If a device is to be considered a wakeup source while inhibited, special care +must be taken when programming its suspend(), as it might need to call device's +open(). Depending on what close() means for the device in question, not +opening() it before going to sleep might make it impossible to provide any +wakeup events. The device is going to sleep anyway. + +Basic event types +~~~~~~~~~~~~~~~~~ + +The most simple event type is EV_KEY, which is used for keys and buttons. +It's reported to the input system via:: + + input_report_key(struct input_dev *dev, int code, int value) + +See uapi/linux/input-event-codes.h for the allowable values of code (from 0 to +KEY_MAX). Value is interpreted as a truth value, i.e. any non-zero value means +key pressed, zero value means key released. The input code generates events only +in case the value is different from before. + +In addition to EV_KEY, there are two more basic event types: EV_REL and +EV_ABS. They are used for relative and absolute values supplied by the +device. A relative value may be for example a mouse movement in the X axis. +The mouse reports it as a relative difference from the last position, +because it doesn't have any absolute coordinate system to work in. Absolute +events are namely for joysticks and digitizers - devices that do work in an +absolute coordinate systems. + +Having the device report EV_REL buttons is as simple as with EV_KEY; simply +set the corresponding bits and call the:: + + input_report_rel(struct input_dev *dev, int code, int value) + +function. Events are generated only for non-zero values. + +However EV_ABS requires a little special care. Before calling +input_register_device, you have to fill additional fields in the input_dev +struct for each absolute axis your device has. If our button device had also +the ABS_X axis:: + + button_dev.absmin[ABS_X] = 0; + button_dev.absmax[ABS_X] = 255; + button_dev.absfuzz[ABS_X] = 4; + button_dev.absflat[ABS_X] = 8; + +Or, you can just say:: + + input_set_abs_params(button_dev, ABS_X, 0, 255, 4, 8); + +This setting would be appropriate for a joystick X axis, with the minimum of +0, maximum of 255 (which the joystick *must* be able to reach, no problem if +it sometimes reports more, but it must be able to always reach the min and +max values), with noise in the data up to +- 4, and with a center flat +position of size 8. + +If you don't need absfuzz and absflat, you can set them to zero, which mean +that the thing is precise and always returns to exactly the center position +(if it has any). + +BITS_TO_LONGS(), BIT_WORD(), BIT_MASK() +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +These three macros from bitops.h help some bitfield computations:: + + BITS_TO_LONGS(x) - returns the length of a bitfield array in longs for + x bits + BIT_WORD(x) - returns the index in the array in longs for bit x + BIT_MASK(x) - returns the index in a long for bit x + +The id* and name fields +~~~~~~~~~~~~~~~~~~~~~~~ + +The dev->name should be set before registering the input device by the input +device driver. It's a string like 'Generic button device' containing a +user friendly name of the device. + +The id* fields contain the bus ID (PCI, USB, ...), vendor ID and device ID +of the device. The bus IDs are defined in input.h. The vendor and device IDs +are defined in pci_ids.h, usb_ids.h and similar include files. These fields +should be set by the input device driver before registering it. + +The idtype field can be used for specific information for the input device +driver. + +The id and name fields can be passed to userland via the evdev interface. + +The keycode, keycodemax, keycodesize fields +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +These three fields should be used by input devices that have dense keymaps. +The keycode is an array used to map from scancodes to input system keycodes. +The keycode max should contain the size of the array and keycodesize the +size of each entry in it (in bytes). + +Userspace can query and alter current scancode to keycode mappings using +EVIOCGKEYCODE and EVIOCSKEYCODE ioctls on corresponding evdev interface. +When a device has all 3 aforementioned fields filled in, the driver may +rely on kernel's default implementation of setting and querying keycode +mappings. + +dev->getkeycode() and dev->setkeycode() +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +getkeycode() and setkeycode() callbacks allow drivers to override default +keycode/keycodesize/keycodemax mapping mechanism provided by input core +and implement sparse keycode maps. + +Key autorepeat +~~~~~~~~~~~~~~ + +... is simple. It is handled by the input.c module. Hardware autorepeat is +not used, because it's not present in many devices and even where it is +present, it is broken sometimes (at keyboards: Toshiba notebooks). To enable +autorepeat for your device, just set EV_REP in dev->evbit. All will be +handled by the input system. + +Other event types, handling output events +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +The other event types up to now are: + +- EV_LED - used for the keyboard LEDs. +- EV_SND - used for keyboard beeps. + +They are very similar to for example key events, but they go in the other +direction - from the system to the input device driver. If your input device +driver can handle these events, it has to set the respective bits in evbit, +*and* also the callback routine:: + + button_dev->event = button_event; + + int button_event(struct input_dev *dev, unsigned int type, + unsigned int code, int value) + { + if (type == EV_SND && code == SND_BELL) { + outb(value, BUTTON_BELL); + return 0; + } + return -1; + } + +This callback routine can be called from an interrupt or a BH (although that +isn't a rule), and thus must not sleep, and must not take too long to finish. diff --git a/Documentation/input/input.rst b/Documentation/input/input.rst new file mode 100644 index 000000000..2c67fa904 --- /dev/null +++ b/Documentation/input/input.rst @@ -0,0 +1,281 @@ +.. include:: <isonum.txt> + +============ +Introduction +============ + +:Copyright: |copy| 1999-2001 Vojtech Pavlik <vojtech@ucw.cz> - Sponsored by SuSE + +Architecture +============ + +Input subsystem is a collection of drivers that is designed to support +all input devices under Linux. Most of the drivers reside in +drivers/input, although quite a few live in drivers/hid and +drivers/platform. + +The core of the input subsystem is the input module, which must be +loaded before any other of the input modules - it serves as a way of +communication between two groups of modules: + +Device drivers +-------------- + +These modules talk to the hardware (for example via USB), and provide +events (keystrokes, mouse movements) to the input module. + +Event handlers +-------------- + +These modules get events from input core and pass them where needed +via various interfaces - keystrokes to the kernel, mouse movements via +a simulated PS/2 interface to GPM and X, and so on. + +Simple Usage +============ + +For the most usual configuration, with one USB mouse and one USB keyboard, +you'll have to load the following modules (or have them built in to the +kernel):: + + input + mousedev + usbcore + uhci_hcd or ohci_hcd or ehci_hcd + usbhid + hid_generic + +After this, the USB keyboard will work straight away, and the USB mouse +will be available as a character device on major 13, minor 63:: + + crw-r--r-- 1 root root 13, 63 Mar 28 22:45 mice + +This device is usually created automatically by the system. The commands +to create it by hand are:: + + cd /dev + mkdir input + mknod input/mice c 13 63 + +After that you have to point GPM (the textmode mouse cut&paste tool) and +XFree to this device to use it - GPM should be called like:: + + gpm -t ps2 -m /dev/input/mice + +And in X:: + + Section "Pointer" + Protocol "ImPS/2" + Device "/dev/input/mice" + ZAxisMapping 4 5 + EndSection + +When you do all of the above, you can use your USB mouse and keyboard. + +Detailed Description +==================== + +Event handlers +-------------- + +Event handlers distribute the events from the devices to userspace and +in-kernel consumers, as needed. + +evdev +~~~~~ + +``evdev`` is the generic input event interface. It passes the events +generated in the kernel straight to the program, with timestamps. The +event codes are the same on all architectures and are hardware +independent. + +This is the preferred interface for userspace to consume user +input, and all clients are encouraged to use it. + +See :ref:`event-interface` for notes on API. + +The devices are in /dev/input:: + + crw-r--r-- 1 root root 13, 64 Apr 1 10:49 event0 + crw-r--r-- 1 root root 13, 65 Apr 1 10:50 event1 + crw-r--r-- 1 root root 13, 66 Apr 1 10:50 event2 + crw-r--r-- 1 root root 13, 67 Apr 1 10:50 event3 + ... + +There are two ranges of minors: 64 through 95 is the static legacy +range. If there are more than 32 input devices in a system, additional +evdev nodes are created with minors starting with 256. + +keyboard +~~~~~~~~ + +``keyboard`` is in-kernel input handler and is a part of VT code. It +consumes keyboard keystrokes and handles user input for VT consoles. + +mousedev +~~~~~~~~ + +``mousedev`` is a hack to make legacy programs that use mouse input +work. It takes events from either mice or digitizers/tablets and makes +a PS/2-style (a la /dev/psaux) mouse device available to the +userland. + +Mousedev devices in /dev/input (as shown above) are:: + + crw-r--r-- 1 root root 13, 32 Mar 28 22:45 mouse0 + crw-r--r-- 1 root root 13, 33 Mar 29 00:41 mouse1 + crw-r--r-- 1 root root 13, 34 Mar 29 00:41 mouse2 + crw-r--r-- 1 root root 13, 35 Apr 1 10:50 mouse3 + ... + ... + crw-r--r-- 1 root root 13, 62 Apr 1 10:50 mouse30 + crw-r--r-- 1 root root 13, 63 Apr 1 10:50 mice + +Each ``mouse`` device is assigned to a single mouse or digitizer, except +the last one - ``mice``. This single character device is shared by all +mice and digitizers, and even if none are connected, the device is +present. This is useful for hotplugging USB mice, so that older programs +that do not handle hotplug can open the device even when no mice are +present. + +CONFIG_INPUT_MOUSEDEV_SCREEN_[XY] in the kernel configuration are +the size of your screen (in pixels) in XFree86. This is needed if you +want to use your digitizer in X, because its movement is sent to X +via a virtual PS/2 mouse and thus needs to be scaled +accordingly. These values won't be used if you use a mouse only. + +Mousedev will generate either PS/2, ImPS/2 (Microsoft IntelliMouse) or +ExplorerPS/2 (IntelliMouse Explorer) protocols, depending on what the +program reading the data wishes. You can set GPM and X to any of +these. You'll need ImPS/2 if you want to make use of a wheel on a USB +mouse and ExplorerPS/2 if you want to use extra (up to 5) buttons. + +joydev +~~~~~~ + +``joydev`` implements v0.x and v1.x Linux joystick API. See +:ref:`joystick-api` for details. + +As soon as any joystick is connected, it can be accessed in /dev/input on:: + + crw-r--r-- 1 root root 13, 0 Apr 1 10:50 js0 + crw-r--r-- 1 root root 13, 1 Apr 1 10:50 js1 + crw-r--r-- 1 root root 13, 2 Apr 1 10:50 js2 + crw-r--r-- 1 root root 13, 3 Apr 1 10:50 js3 + ... + +And so on up to js31 in legacy range, and additional nodes with minors +above 256 if there are more joystick devices. + +Device drivers +-------------- + +Device drivers are the modules that generate events. + +hid-generic +~~~~~~~~~~~ + +``hid-generic`` is one of the largest and most complex driver of the +whole suite. It handles all HID devices, and because there is a very +wide variety of them, and because the USB HID specification isn't +simple, it needs to be this big. + +Currently, it handles USB mice, joysticks, gamepads, steering wheels, +keyboards, trackballs and digitizers. + +However, USB uses HID also for monitor controls, speaker controls, UPSs, +LCDs and many other purposes. + +The monitor and speaker controls should be easy to add to the hid/input +interface, but for the UPSs and LCDs it doesn't make much sense. For this, +the hiddev interface was designed. See Documentation/hid/hiddev.rst +for more information about it. + +The usage of the usbhid module is very simple, it takes no parameters, +detects everything automatically and when a HID device is inserted, it +detects it appropriately. + +However, because the devices vary wildly, you might happen to have a +device that doesn't work well. In that case #define DEBUG at the beginning +of hid-core.c and send me the syslog traces. + +usbmouse +~~~~~~~~ + +For embedded systems, for mice with broken HID descriptors and just any +other use when the big usbhid wouldn't be a good choice, there is the +usbmouse driver. It handles USB mice only. It uses a simpler HIDBP +protocol. This also means the mice must support this simpler protocol. Not +all do. If you don't have any strong reason to use this module, use usbhid +instead. + +usbkbd +~~~~~~ + +Much like usbmouse, this module talks to keyboards with a simplified +HIDBP protocol. It's smaller, but doesn't support any extra special keys. +Use usbhid instead if there isn't any special reason to use this. + +psmouse +~~~~~~~ + +This is driver for all flavors of pointing devices using PS/2 +protocol, including Synaptics and ALPS touchpads, Intellimouse +Explorer devices, Logitech PS/2 mice and so on. + +atkbd +~~~~~ + +This is driver for PS/2 (AT) keyboards. + +iforce +~~~~~~ + +A driver for I-Force joysticks and wheels, both over USB and RS232. +It includes Force Feedback support now, even though Immersion +Corp. considers the protocol a trade secret and won't disclose a word +about it. + +Verifying if it works +===================== + +Typing a couple keys on the keyboard should be enough to check that +a keyboard works and is correctly connected to the kernel keyboard +driver. + +Doing a ``cat /dev/input/mouse0`` (c, 13, 32) will verify that a mouse +is also emulated; characters should appear if you move it. + +You can test the joystick emulation with the ``jstest`` utility, +available in the joystick package (see :ref:`joystick-doc`). + +You can test the event devices with the ``evtest`` utility. + +.. _event-interface: + +Event interface +=============== + +You can use blocking and nonblocking reads, and also select() on the +/dev/input/eventX devices, and you'll always get a whole number of input +events on a read. Their layout is:: + + struct input_event { + struct timeval time; + unsigned short type; + unsigned short code; + unsigned int value; + }; + +``time`` is the timestamp, it returns the time at which the event happened. +Type is for example EV_REL for relative movement, EV_KEY for a keypress or +release. More types are defined in include/uapi/linux/input-event-codes.h. + +``code`` is event code, for example REL_X or KEY_BACKSPACE, again a complete +list is in include/uapi/linux/input-event-codes.h. + +``value`` is the value the event carries. Either a relative change for +EV_REL, absolute new value for EV_ABS (joysticks ...), or 0 for EV_KEY for +release, 1 for keypress and 2 for autorepeat. + +See :ref:`input-event-codes` for more information about various even codes. diff --git a/Documentation/input/input_kapi.rst b/Documentation/input/input_kapi.rst new file mode 100644 index 000000000..41f1b7e6b --- /dev/null +++ b/Documentation/input/input_kapi.rst @@ -0,0 +1,17 @@ +.. include:: <isonum.txt> + +################################ +Linux Input Subsystem kernel API +################################ + +.. class:: toc-title + + Table of Contents + +.. toctree:: + :maxdepth: 2 + :numbered: + + input-programming + gameport-programming + notifier diff --git a/Documentation/input/input_uapi.rst b/Documentation/input/input_uapi.rst new file mode 100644 index 000000000..4a0391609 --- /dev/null +++ b/Documentation/input/input_uapi.rst @@ -0,0 +1,22 @@ +.. include:: <isonum.txt> + +################################### +Linux Input Subsystem userspace API +################################### + +.. class:: toc-title + + Table of Contents + +.. toctree:: + :maxdepth: 2 + :numbered: + + input + event-codes + multi-touch-protocol + gamepad + ff + joydev/index + uinput + userio diff --git a/Documentation/input/interactive.svg b/Documentation/input/interactive.svg new file mode 100644 index 000000000..a3513709a --- /dev/null +++ b/Documentation/input/interactive.svg @@ -0,0 +1,24 @@ +<svg width="5.75in" height="3.90in" version="1.1" viewBox="1178 3138 6779.9424 4671.3427" xmlns="http://www.w3.org/2000/svg"> + <polyline transform="translate(-18.5,-16.294)" points="1200 3600 1800 3600 2400 4800 3e3 4800 4200 5700 4800 5700" fill="none" stroke="#000" stroke-width="15"/> + <rect x="1181.5" y="3133.7" width="3600" height="3150" rx="0" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="1200 4800 4800 4800" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="2400 4800 2400 6525 1950 7125 1950 7800" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="3e3 4800 3e3 6525 3600 7125 3600 7800" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="3837 5389 4125 5100 5400 5100" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="3889 5292 3826 5398 3932 5334" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="2112 4189 2400 3900 5400 3900" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="2164 4092 2101 4198 2207 4134" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="4800 5700 5400 5700" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="1800 3600 5400 3600" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="2700 4784 2700 4425 5400 4425" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="2670 4678 2700 4798 2730 4678" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="1967 7800 3583 7800" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="3478 7830 3598 7800 3478 7770" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-18.5,-16.294)" points="2072 7770 1952 7800 2072 7830" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <text x="2775" y="7725" font-family="sans-serif" font-size="144px" stroke="#000000" stroke-width=".025in" text-anchor="middle" xml:space="preserve">Dead band</text> + <text x="5400" y="5700" font-family="sans-serif" font-size="144px" stroke="#000000" stroke-width=".025in" xml:space="preserve">right saturation</text> + <text x="5400" y="3600" font-family="sans-serif" font-size="144px" stroke="#000000" stroke-width=".025in" xml:space="preserve">left saturation</text> + <text x="5400" y="3900" font-family="sans-serif" font-size="144px" stroke="#000000" stroke-width=".025in" xml:space="preserve">left coeff ( positive in that case )</text> + <text x="5475" y="5100" font-family="sans-serif" font-size="144px" stroke="#000000" stroke-width=".025in" xml:space="preserve">right coeff ( negative in that case )</text> + <text x="5400" y="4425" font-family="sans-serif" font-size="144px" stroke="#000000" stroke-width=".025in" xml:space="preserve">center</text> +</svg> diff --git a/Documentation/input/joydev/index.rst b/Documentation/input/joydev/index.rst new file mode 100644 index 000000000..ebcff4305 --- /dev/null +++ b/Documentation/input/joydev/index.rst @@ -0,0 +1,17 @@ +.. include:: <isonum.txt> + +====================== +Linux Joystick support +====================== + +:Copyright: |copy| 1996-2000 Vojtech Pavlik <vojtech@ucw.cz> - Sponsored by SuSE + +.. class:: toc-title + + Table of Contents + +.. toctree:: + :maxdepth: 3 + + joystick + joystick-api diff --git a/Documentation/input/joydev/joystick-api.rst b/Documentation/input/joydev/joystick-api.rst new file mode 100644 index 000000000..5db6dc6fe --- /dev/null +++ b/Documentation/input/joydev/joystick-api.rst @@ -0,0 +1,348 @@ +.. _joystick-api: + +===================== +Programming Interface +===================== + +:Author: Ragnar Hojland Espinosa <ragnar@macula.net> - 7 Aug 1998 + +Introduction +============ + +.. important:: + This document describes legacy ``js`` interface. Newer clients are + encouraged to switch to the generic event (``evdev``) interface. + +The 1.0 driver uses a new, event based approach to the joystick driver. +Instead of the user program polling for the joystick values, the joystick +driver now reports only any changes of its state. See joystick-api.txt, +joystick.h and jstest.c included in the joystick package for more +information. The joystick device can be used in either blocking or +nonblocking mode, and supports select() calls. + +For backward compatibility the old (v0.x) interface is still included. +Any call to the joystick driver using the old interface will return values +that are compatible to the old interface. This interface is still limited +to 2 axes, and applications using it usually decode only 2 buttons, although +the driver provides up to 32. + +Initialization +============== + +Open the joystick device following the usual semantics (that is, with open). +Since the driver now reports events instead of polling for changes, +immediately after the open it will issue a series of synthetic events +(JS_EVENT_INIT) that you can read to obtain the initial state of the +joystick. + +By default, the device is opened in blocking mode:: + + int fd = open ("/dev/input/js0", O_RDONLY); + + +Event Reading +============= + +:: + + struct js_event e; + read (fd, &e, sizeof(e)); + +where js_event is defined as:: + + struct js_event { + __u32 time; /* event timestamp in milliseconds */ + __s16 value; /* value */ + __u8 type; /* event type */ + __u8 number; /* axis/button number */ + }; + +If the read is successful, it will return sizeof(e), unless you wanted to read +more than one event per read as described in section 3.1. + + +js_event.type +------------- + +The possible values of ``type`` are:: + + #define JS_EVENT_BUTTON 0x01 /* button pressed/released */ + #define JS_EVENT_AXIS 0x02 /* joystick moved */ + #define JS_EVENT_INIT 0x80 /* initial state of device */ + +As mentioned above, the driver will issue synthetic JS_EVENT_INIT ORed +events on open. That is, if it's issuing an INIT BUTTON event, the +current type value will be:: + + int type = JS_EVENT_BUTTON | JS_EVENT_INIT; /* 0x81 */ + +If you choose not to differentiate between synthetic or real events +you can turn off the JS_EVENT_INIT bits:: + + type &= ~JS_EVENT_INIT; /* 0x01 */ + + +js_event.number +--------------- + +The values of ``number`` correspond to the axis or button that +generated the event. Note that they carry separate numeration (that +is, you have both an axis 0 and a button 0). Generally, + + =============== ======= + Axis number + =============== ======= + 1st Axis X 0 + 1st Axis Y 1 + 2nd Axis X 2 + 2nd Axis Y 3 + ...and so on + =============== ======= + +Hats vary from one joystick type to another. Some can be moved in 8 +directions, some only in 4. The driver, however, always reports a hat as two +independent axes, even if the hardware doesn't allow independent movement. + + +js_event.value +-------------- + +For an axis, ``value`` is a signed integer between -32767 and +32767 +representing the position of the joystick along that axis. If you +don't read a 0 when the joystick is ``dead``, or if it doesn't span the +full range, you should recalibrate it (with, for example, jscal). + +For a button, ``value`` for a press button event is 1 and for a release +button event is 0. + +Though this:: + + if (js_event.type == JS_EVENT_BUTTON) { + buttons_state ^= (1 << js_event.number); + } + +may work well if you handle JS_EVENT_INIT events separately, + +:: + + if ((js_event.type & ~JS_EVENT_INIT) == JS_EVENT_BUTTON) { + if (js_event.value) + buttons_state |= (1 << js_event.number); + else + buttons_state &= ~(1 << js_event.number); + } + +is much safer since it can't lose sync with the driver. As you would +have to write a separate handler for JS_EVENT_INIT events in the first +snippet, this ends up being shorter. + + +js_event.time +------------- + +The time an event was generated is stored in ``js_event.time``. It's a time +in milliseconds since ... well, since sometime in the past. This eases the +task of detecting double clicks, figuring out if movement of axis and button +presses happened at the same time, and similar. + + +Reading +======= + +If you open the device in blocking mode, a read will block (that is, +wait) forever until an event is generated and effectively read. There +are two alternatives if you can't afford to wait forever (which is, +admittedly, a long time;) + + a) use select to wait until there's data to be read on fd, or + until it timeouts. There's a good example on the select(2) + man page. + + b) open the device in non-blocking mode (O_NONBLOCK) + + +O_NONBLOCK +---------- + +If read returns -1 when reading in O_NONBLOCK mode, this isn't +necessarily a "real" error (check errno(3)); it can just mean there +are no events pending to be read on the driver queue. You should read +all events on the queue (that is, until you get a -1). + +For example, + +:: + + while (1) { + while (read (fd, &e, sizeof(e)) > 0) { + process_event (e); + } + /* EAGAIN is returned when the queue is empty */ + if (errno != EAGAIN) { + /* error */ + } + /* do something interesting with processed events */ + } + +One reason for emptying the queue is that if it gets full you'll start +missing events since the queue is finite, and older events will get +overwritten. + +The other reason is that you want to know all that happened, and not +delay the processing till later. + +Why can the queue get full? Because you don't empty the queue as +mentioned, or because too much time elapses from one read to another +and too many events to store in the queue get generated. Note that +high system load may contribute to space those reads even more. + +If time between reads is enough to fill the queue and lose an event, +the driver will switch to startup mode and next time you read it, +synthetic events (JS_EVENT_INIT) will be generated to inform you of +the actual state of the joystick. + + +.. note:: + + As of version 1.2.8, the queue is circular and able to hold 64 + events. You can increment this size bumping up JS_BUFF_SIZE in + joystick.h and recompiling the driver. + + +In the above code, you might as well want to read more than one event +at a time using the typical read(2) functionality. For that, you would +replace the read above with something like:: + + struct js_event mybuffer[0xff]; + int i = read (fd, mybuffer, sizeof(mybuffer)); + +In this case, read would return -1 if the queue was empty, or some +other value in which the number of events read would be i / +sizeof(js_event) Again, if the buffer was full, it's a good idea to +process the events and keep reading it until you empty the driver queue. + + +IOCTLs +====== + +The joystick driver defines the following ioctl(2) operations:: + + /* function 3rd arg */ + #define JSIOCGAXES /* get number of axes char */ + #define JSIOCGBUTTONS /* get number of buttons char */ + #define JSIOCGVERSION /* get driver version int */ + #define JSIOCGNAME(len) /* get identifier string char */ + #define JSIOCSCORR /* set correction values &js_corr */ + #define JSIOCGCORR /* get correction values &js_corr */ + +For example, to read the number of axes:: + + char number_of_axes; + ioctl (fd, JSIOCGAXES, &number_of_axes); + + +JSIOGCVERSION +------------- + +JSIOGCVERSION is a good way to check in run-time whether the running +driver is 1.0+ and supports the event interface. If it is not, the +IOCTL will fail. For a compile-time decision, you can test the +JS_VERSION symbol:: + + #ifdef JS_VERSION + #if JS_VERSION > 0xsomething + + +JSIOCGNAME +---------- + +JSIOCGNAME(len) allows you to get the name string of the joystick - the same +as is being printed at boot time. The 'len' argument is the length of the +buffer provided by the application asking for the name. It is used to avoid +possible overrun should the name be too long:: + + char name[128]; + if (ioctl(fd, JSIOCGNAME(sizeof(name)), name) < 0) + strscpy(name, "Unknown", sizeof(name)); + printf("Name: %s\n", name); + + +JSIOC[SG]CORR +------------- + +For usage on JSIOC[SG]CORR I suggest you to look into jscal.c They are +not needed in a normal program, only in joystick calibration software +such as jscal or kcmjoy. These IOCTLs and data types aren't considered +to be in the stable part of the API, and therefore may change without +warning in following releases of the driver. + +Both JSIOCSCORR and JSIOCGCORR expect &js_corr to be able to hold +information for all axes. That is, struct js_corr corr[MAX_AXIS]; + +struct js_corr is defined as:: + + struct js_corr { + __s32 coef[8]; + __u16 prec; + __u16 type; + }; + +and ``type``:: + + #define JS_CORR_NONE 0x00 /* returns raw values */ + #define JS_CORR_BROKEN 0x01 /* broken line */ + + +Backward compatibility +====================== + +The 0.x joystick driver API is quite limited and its usage is deprecated. +The driver offers backward compatibility, though. Here's a quick summary:: + + struct JS_DATA_TYPE js; + while (1) { + if (read (fd, &js, JS_RETURN) != JS_RETURN) { + /* error */ + } + usleep (1000); + } + +As you can figure out from the example, the read returns immediately, +with the actual state of the joystick:: + + struct JS_DATA_TYPE { + int buttons; /* immediate button state */ + int x; /* immediate x axis value */ + int y; /* immediate y axis value */ + }; + +and JS_RETURN is defined as:: + + #define JS_RETURN sizeof(struct JS_DATA_TYPE) + +To test the state of the buttons, + +:: + + first_button_state = js.buttons & 1; + second_button_state = js.buttons & 2; + +The axis values do not have a defined range in the original 0.x driver, +except that the values are non-negative. The 1.2.8+ drivers use a +fixed range for reporting the values, 1 being the minimum, 128 the +center, and 255 maximum value. + +The v0.8.0.2 driver also had an interface for 'digital joysticks', (now +called Multisystem joysticks in this driver), under /dev/djsX. This driver +doesn't try to be compatible with that interface. + + +Final Notes +=========== + +:: + + ____/| Comments, additions, and specially corrections are welcome. + \ o.O| Documentation valid for at least version 1.2.8 of the joystick + =(_)= driver and as usual, the ultimate source for documentation is + U to "Use The Source Luke" or, at your convenience, Vojtech ;) diff --git a/Documentation/input/joydev/joystick.rst b/Documentation/input/joydev/joystick.rst new file mode 100644 index 000000000..6d7213967 --- /dev/null +++ b/Documentation/input/joydev/joystick.rst @@ -0,0 +1,586 @@ +.. include:: <isonum.txt> + +.. _joystick-doc: + +Introduction +============ + +The joystick driver for Linux provides support for a variety of joysticks +and similar devices. It is based on a larger project aiming to support all +input devices in Linux. + +The mailing list for the project is: + + linux-input@vger.kernel.org + +send "subscribe linux-input" to majordomo@vger.kernel.org to subscribe to it. + +Usage +===== + +For basic usage you just choose the right options in kernel config and +you should be set. + +Utilities +--------- + +For testing and other purposes (for example serial devices), there is a set +of utilities, such as ``jstest``, ``jscal``, and ``evtest``, +usually packaged as ``joystick``, ``input-utils``, ``evtest``, and so on. + +``inputattach`` utility is required if your joystick is connected to a +serial port. + +Device nodes +------------ + +For applications to be able to use the joysticks, device nodes should be +created in /dev. Normally it is done automatically by the system, but +it can also be done by hand:: + + cd /dev + rm js* + mkdir input + mknod input/js0 c 13 0 + mknod input/js1 c 13 1 + mknod input/js2 c 13 2 + mknod input/js3 c 13 3 + ln -s input/js0 js0 + ln -s input/js1 js1 + ln -s input/js2 js2 + ln -s input/js3 js3 + +For testing with inpututils it's also convenient to create these:: + + mknod input/event0 c 13 64 + mknod input/event1 c 13 65 + mknod input/event2 c 13 66 + mknod input/event3 c 13 67 + +Modules needed +-------------- + +For all joystick drivers to function, you'll need the userland interface +module in kernel, either loaded or compiled in:: + + modprobe joydev + +For gameport joysticks, you'll have to load the gameport driver as well:: + + modprobe ns558 + +And for serial port joysticks, you'll need the serial input line +discipline module loaded and the inputattach utility started:: + + modprobe serport + inputattach -xxx /dev/tts/X & + +In addition to that, you'll need the joystick driver module itself, most +usually you'll have an analog joystick:: + + modprobe analog + +For automatic module loading, something like this might work - tailor to +your needs:: + + alias tty-ldisc-2 serport + alias char-major-13 input + above input joydev ns558 analog + options analog map=gamepad,none,2btn + +Verifying that it works +----------------------- + +For testing the joystick driver functionality, there is the jstest +program in the utilities package. You run it by typing:: + + jstest /dev/input/js0 + +And it should show a line with the joystick values, which update as you +move the stick, and press its buttons. The axes should all be zero when the +joystick is in the center position. They should not jitter by themselves to +other close values, and they also should be steady in any other position of +the stick. They should have the full range from -32767 to 32767. If all this +is met, then it's all fine, and you can play the games. :) + +If it's not, then there might be a problem. Try to calibrate the joystick, +and if it still doesn't work, read the drivers section of this file, the +troubleshooting section, and the FAQ. + +Calibration +----------- + +For most joysticks you won't need any manual calibration, since the +joystick should be autocalibrated by the driver automagically. However, with +some analog joysticks, that either do not use linear resistors, or if you +want better precision, you can use the jscal program:: + + jscal -c /dev/input/js0 + +included in the joystick package to set better correction coefficients than +what the driver would choose itself. + +After calibrating the joystick you can verify if you like the new +calibration using the jstest command, and if you do, you then can save the +correction coefficients into a file:: + + jscal -p /dev/input/js0 > /etc/joystick.cal + +And add a line to your rc script executing that file:: + + source /etc/joystick.cal + +This way, after the next reboot your joystick will remain calibrated. You +can also add the ``jscal -p`` line to your shutdown script. + +Hardware-specific driver information +==================================== + +In this section each of the separate hardware specific drivers is described. + +Analog joysticks +---------------- + +The analog.c driver uses the standard analog inputs of the gameport, and thus +supports all standard joysticks and gamepads. It uses a very advanced +routine for this, allowing for data precision that can't be found on any +other system. + +It also supports extensions like additional hats and buttons compatible +with CH Flightstick Pro, ThrustMaster FCS or 6 and 8 button gamepads. Saitek +Cyborg 'digital' joysticks are also supported by this driver, because +they're basically souped up CHF sticks. + +However the only types that can be autodetected are: + +* 2-axis, 4-button joystick +* 3-axis, 4-button joystick +* 4-axis, 4-button joystick +* Saitek Cyborg 'digital' joysticks + +For other joystick types (more/less axes, hats, and buttons) support +you'll need to specify the types either on the kernel command line or on the +module command line, when inserting analog into the kernel. The +parameters are:: + + analog.map=<type1>,<type2>,<type3>,.... + +'type' is type of the joystick from the table below, defining joysticks +present on gameports in the system, starting with gameport0, second 'type' +entry defining joystick on gameport1 and so on. + + ========= ===================================================== + Type Meaning + ========= ===================================================== + none No analog joystick on that port + auto Autodetect joystick + 2btn 2-button n-axis joystick + y-joy Two 2-button 2-axis joysticks on an Y-cable + y-pad Two 2-button 2-axis gamepads on an Y-cable + fcs Thrustmaster FCS compatible joystick + chf Joystick with a CH Flightstick compatible hat + fullchf CH Flightstick compatible with two hats and 6 buttons + gamepad 4/6-button n-axis gamepad + gamepad8 8-button 2-axis gamepad + ========= ===================================================== + +In case your joystick doesn't fit in any of the above categories, you can +specify the type as a number by combining the bits in the table below. This +is not recommended unless you really know what are you doing. It's not +dangerous, but not simple either. + + ==== ========================= + Bit Meaning + ==== ========================= + 0 Axis X1 + 1 Axis Y1 + 2 Axis X2 + 3 Axis Y2 + 4 Button A + 5 Button B + 6 Button C + 7 Button D + 8 CHF Buttons X and Y + 9 CHF Hat 1 + 10 CHF Hat 2 + 11 FCS Hat + 12 Pad Button X + 13 Pad Button Y + 14 Pad Button U + 15 Pad Button V + 16 Saitek F1-F4 Buttons + 17 Saitek Digital Mode + 19 GamePad + 20 Joy2 Axis X1 + 21 Joy2 Axis Y1 + 22 Joy2 Axis X2 + 23 Joy2 Axis Y2 + 24 Joy2 Button A + 25 Joy2 Button B + 26 Joy2 Button C + 27 Joy2 Button D + 31 Joy2 GamePad + ==== ========================= + +Microsoft SideWinder joysticks +------------------------------ + +Microsoft 'Digital Overdrive' protocol is supported by the sidewinder.c +module. All currently supported joysticks: + +* Microsoft SideWinder 3D Pro +* Microsoft SideWinder Force Feedback Pro +* Microsoft SideWinder Force Feedback Wheel +* Microsoft SideWinder FreeStyle Pro +* Microsoft SideWinder GamePad (up to four, chained) +* Microsoft SideWinder Precision Pro +* Microsoft SideWinder Precision Pro USB + +are autodetected, and thus no module parameters are needed. + +There is one caveat with the 3D Pro. There are 9 buttons reported, +although the joystick has only 8. The 9th button is the mode switch on the +rear side of the joystick. However, moving it, you'll reset the joystick, +and make it unresponsive for about a one third of a second. Furthermore, the +joystick will also re-center itself, taking the position it was in during +this time as a new center position. Use it if you want, but think first. + +The SideWinder Standard is not a digital joystick, and thus is supported +by the analog driver described above. + +Logitech ADI devices +-------------------- + +Logitech ADI protocol is supported by the adi.c module. It should support +any Logitech device using this protocol. This includes, but is not limited +to: + +* Logitech CyberMan 2 +* Logitech ThunderPad Digital +* Logitech WingMan Extreme Digital +* Logitech WingMan Formula +* Logitech WingMan Interceptor +* Logitech WingMan GamePad +* Logitech WingMan GamePad USB +* Logitech WingMan GamePad Extreme +* Logitech WingMan Extreme Digital 3D + +ADI devices are autodetected, and the driver supports up to two (any +combination of) devices on a single gameport, using a Y-cable or chained +together. + +Logitech WingMan Joystick, Logitech WingMan Attack, Logitech WingMan +Extreme and Logitech WingMan ThunderPad are not digital joysticks and are +handled by the analog driver described above. Logitech WingMan Warrior and +Logitech Magellan are supported by serial drivers described below. Logitech +WingMan Force and Logitech WingMan Formula Force are supported by the +I-Force driver described below. Logitech CyberMan is not supported yet. + +Gravis GrIP +----------- + +Gravis GrIP protocol is supported by the grip.c module. It currently +supports: + +* Gravis GamePad Pro +* Gravis BlackHawk Digital +* Gravis Xterminator +* Gravis Xterminator DualControl + +All these devices are autodetected, and you can even use any combination +of up to two of these pads either chained together or using a Y-cable on a +single gameport. + +GrIP MultiPort isn't supported yet. Gravis Stinger is a serial device and is +supported by the stinger driver. Other Gravis joysticks are supported by the +analog driver. + +FPGaming A3D and MadCatz A3D +---------------------------- + +The Assassin 3D protocol created by FPGaming, is used both by FPGaming +themselves and is licensed to MadCatz. A3D devices are supported by the +a3d.c module. It currently supports: + +* FPGaming Assassin 3D +* MadCatz Panther +* MadCatz Panther XL + +All these devices are autodetected. Because the Assassin 3D and the Panther +allow connecting analog joysticks to them, you'll need to load the analog +driver as well to handle the attached joysticks. + +The trackball should work with USB mousedev module as a normal mouse. See +the USB documentation for how to setup a USB mouse. + +ThrustMaster DirectConnect (BSP) +-------------------------------- + +The TM DirectConnect (BSP) protocol is supported by the tmdc.c +module. This includes, but is not limited to: + +* ThrustMaster Millennium 3D Interceptor +* ThrustMaster 3D Rage Pad +* ThrustMaster Fusion Digital Game Pad + +Devices not directly supported, but hopefully working are: + +* ThrustMaster FragMaster +* ThrustMaster Attack Throttle + +If you have one of these, contact me. + +TMDC devices are autodetected, and thus no parameters to the module +are needed. Up to two TMDC devices can be connected to one gameport, using +a Y-cable. + +Creative Labs Blaster +--------------------- + +The Blaster protocol is supported by the cobra.c module. It supports only +the: + +* Creative Blaster GamePad Cobra + +Up to two of these can be used on a single gameport, using a Y-cable. + +Genius Digital joysticks +------------------------ + +The Genius digitally communicating joysticks are supported by the gf2k.c +module. This includes: + +* Genius Flight2000 F-23 joystick +* Genius Flight2000 F-31 joystick +* Genius G-09D gamepad + +Other Genius digital joysticks are not supported yet, but support can be +added fairly easily. + +InterAct Digital joysticks +-------------------------- + +The InterAct digitally communicating joysticks are supported by the +interact.c module. This includes: + +* InterAct HammerHead/FX gamepad +* InterAct ProPad8 gamepad + +Other InterAct digital joysticks are not supported yet, but support can be +added fairly easily. + +PDPI Lightning 4 gamecards +-------------------------- + +PDPI Lightning 4 gamecards are supported by the lightning.c module. +Once the module is loaded, the analog driver can be used to handle the +joysticks. Digitally communicating joystick will work only on port 0, while +using Y-cables, you can connect up to 8 analog joysticks to a single L4 +card, 16 in case you have two in your system. + +Trident 4DWave / Aureal Vortex +------------------------------ + +Soundcards with a Trident 4DWave DX/NX or Aureal Vortex/Vortex2 chipset +provide an "Enhanced Game Port" mode where the soundcard handles polling the +joystick. This mode is supported by the pcigame.c module. Once loaded the +analog driver can use the enhanced features of these gameports.. + +Crystal SoundFusion +------------------- + +Soundcards with Crystal SoundFusion chipsets provide an "Enhanced Game +Port", much like the 4DWave or Vortex above. This, and also the normal mode +for the port of the SoundFusion is supported by the cs461x.c module. + +SoundBlaster Live! +------------------ + +The Live! has a special PCI gameport, which, although it doesn't provide +any "Enhanced" stuff like 4DWave and friends, is quite a bit faster than +its ISA counterparts. It also requires special support, hence the +emu10k1-gp.c module for it instead of the normal ns558.c one. + +SoundBlaster 64 and 128 - ES1370 and ES1371, ESS Solo1 and S3 SonicVibes +------------------------------------------------------------------------ + +These PCI soundcards have specific gameports. They are handled by the +sound drivers themselves. Make sure you select gameport support in the +joystick menu and sound card support in the sound menu for your appropriate +card. + +Amiga +----- + +Amiga joysticks, connected to an Amiga, are supported by the amijoy.c +driver. Since they can't be autodetected, the driver has a command line: + + amijoy.map=<a>,<b> + +a and b define the joysticks connected to the JOY0DAT and JOY1DAT ports of +the Amiga. + + ====== =========================== + Value Joystick type + ====== =========================== + 0 None + 1 1-button digital joystick + ====== =========================== + +No more joystick types are supported now, but that should change in the +future if I get an Amiga in the reach of my fingers. + +Game console and 8-bit pads and joysticks +----------------------------------------- + +These pads and joysticks are not designed for PCs and other computers +Linux runs on, and usually require a special connector for attaching +them through a parallel port. + +See :ref:`joystick-parport` for more info. + +SpaceTec/LabTec devices +----------------------- + +SpaceTec serial devices communicate using the SpaceWare protocol. It is +supported by the spaceorb.c and spaceball.c drivers. The devices currently +supported by spaceorb.c are: + +* SpaceTec SpaceBall Avenger +* SpaceTec SpaceOrb 360 + +Devices currently supported by spaceball.c are: + +* SpaceTec SpaceBall 4000 FLX + +In addition to having the spaceorb/spaceball and serport modules in the +kernel, you also need to attach a serial port to it. To do that, run the +inputattach program:: + + inputattach --spaceorb /dev/tts/x & + +or:: + + inputattach --spaceball /dev/tts/x & + +where /dev/tts/x is the serial port which the device is connected to. After +doing this, the device will be reported and will start working. + +There is one caveat with the SpaceOrb. The button #6, the one on the bottom +side of the orb, although reported as an ordinary button, causes internal +recentering of the spaceorb, moving the zero point to the position in which +the ball is at the moment of pressing the button. So, think first before +you bind it to some other function. + +SpaceTec SpaceBall 2003 FLX and 3003 FLX are not supported yet. + +Logitech SWIFT devices +---------------------- + +The SWIFT serial protocol is supported by the warrior.c module. It +currently supports only the: + +* Logitech WingMan Warrior + +but in the future, Logitech CyberMan (the original one, not CM2) could be +supported as well. To use the module, you need to run inputattach after you +insert/compile the module into your kernel:: + + inputattach --warrior /dev/tts/x & + +/dev/tts/x is the serial port your Warrior is attached to. + +Magellan / Space Mouse +---------------------- + +The Magellan (or Space Mouse), manufactured by LogiCad3d (formerly Space +Systems), for many other companies (Logitech, HP, ...) is supported by the +joy-magellan module. It currently supports only the: + +* Magellan 3D +* Space Mouse + +models; the additional buttons on the 'Plus' versions are not supported yet. + +To use it, you need to attach the serial port to the driver using the:: + + inputattach --magellan /dev/tts/x & + +command. After that the Magellan will be detected, initialized, will beep, +and the /dev/input/jsX device should become usable. + +I-Force devices +--------------- + +All I-Force devices are supported by the iforce module. This includes: + +* AVB Mag Turbo Force +* AVB Top Shot Pegasus +* AVB Top Shot Force Feedback Racing Wheel +* Boeder Force Feedback Wheel +* Logitech WingMan Force +* Logitech WingMan Force Wheel +* Guillemot Race Leader Force Feedback +* Guillemot Force Feedback Racing Wheel +* Thrustmaster Motor Sport GT + +To use it, you need to attach the serial port to the driver using the:: + + inputattach --iforce /dev/tts/x & + +command. After that the I-Force device will be detected, and the +/dev/input/jsX device should become usable. + +In case you're using the device via the USB port, the inputattach command +isn't needed. + +The I-Force driver now supports force feedback via the event interface. + +Please note that Logitech WingMan 3D devices are _not_ supported by this +module, rather by hid. Force feedback is not supported for those devices. +Logitech gamepads are also hid devices. + +Gravis Stinger gamepad +---------------------- + +The Gravis Stinger serial port gamepad, designed for use with laptop +computers, is supported by the stinger.c module. To use it, attach the +serial port to the driver using:: + + inputattach --stinger /dev/tty/x & + +where x is the number of the serial port. + +Troubleshooting +=============== + +There is quite a high probability that you run into some problems. For +testing whether the driver works, if in doubt, use the jstest utility in +some of its modes. The most useful modes are "normal" - for the 1.x +interface, and "old" for the "0.x" interface. You run it by typing:: + + jstest --normal /dev/input/js0 + jstest --old /dev/input/js0 + +Additionally you can do a test with the evtest utility:: + + evtest /dev/input/event0 + +Oh, and read the FAQ! :) + +FAQ +=== + +:Q: Running 'jstest /dev/input/js0' results in "File not found" error. What's the + cause? +:A: The device files don't exist. Create them (see section 2.2). + +:Q: Is it possible to connect my old Atari/Commodore/Amiga/console joystick + or pad that uses a 9-pin D-type Cannon connector to the serial port of my + PC? +:A: Yes, it is possible, but it'll burn your serial port or the pad. It + won't work, of course. + +:Q: My joystick doesn't work with Quake / Quake 2. What's the cause? +:A: Quake / Quake 2 don't support joystick. Use joy2key to simulate keypresses + for them. diff --git a/Documentation/input/multi-touch-protocol.rst b/Documentation/input/multi-touch-protocol.rst new file mode 100644 index 000000000..1085cbee4 --- /dev/null +++ b/Documentation/input/multi-touch-protocol.rst @@ -0,0 +1,415 @@ +.. include:: <isonum.txt> + +========================= +Multi-touch (MT) Protocol +========================= + +:Copyright: |copy| 2009-2010 Henrik Rydberg <rydberg@euromail.se> + + +Introduction +------------ + +In order to utilize the full power of the new multi-touch and multi-user +devices, a way to report detailed data from multiple contacts, i.e., +objects in direct contact with the device surface, is needed. This +document describes the multi-touch (MT) protocol which allows kernel +drivers to report details for an arbitrary number of contacts. + +The protocol is divided into two types, depending on the capabilities of the +hardware. For devices handling anonymous contacts (type A), the protocol +describes how to send the raw data for all contacts to the receiver. For +devices capable of tracking identifiable contacts (type B), the protocol +describes how to send updates for individual contacts via event slots. + +.. note:: + MT protocol type A is obsolete, all kernel drivers have been + converted to use type B. + +Protocol Usage +-------------- + +Contact details are sent sequentially as separate packets of ABS_MT +events. Only the ABS_MT events are recognized as part of a contact +packet. Since these events are ignored by current single-touch (ST) +applications, the MT protocol can be implemented on top of the ST protocol +in an existing driver. + +Drivers for type A devices separate contact packets by calling +input_mt_sync() at the end of each packet. This generates a SYN_MT_REPORT +event, which instructs the receiver to accept the data for the current +contact and prepare to receive another. + +Drivers for type B devices separate contact packets by calling +input_mt_slot(), with a slot as argument, at the beginning of each packet. +This generates an ABS_MT_SLOT event, which instructs the receiver to +prepare for updates of the given slot. + +All drivers mark the end of a multi-touch transfer by calling the usual +input_sync() function. This instructs the receiver to act upon events +accumulated since last EV_SYN/SYN_REPORT and prepare to receive a new set +of events/packets. + +The main difference between the stateless type A protocol and the stateful +type B slot protocol lies in the usage of identifiable contacts to reduce +the amount of data sent to userspace. The slot protocol requires the use of +the ABS_MT_TRACKING_ID, either provided by the hardware or computed from +the raw data [#f5]_. + +For type A devices, the kernel driver should generate an arbitrary +enumeration of the full set of anonymous contacts currently on the +surface. The order in which the packets appear in the event stream is not +important. Event filtering and finger tracking is left to user space [#f3]_. + +For type B devices, the kernel driver should associate a slot with each +identified contact, and use that slot to propagate changes for the contact. +Creation, replacement and destruction of contacts is achieved by modifying +the ABS_MT_TRACKING_ID of the associated slot. A non-negative tracking id +is interpreted as a contact, and the value -1 denotes an unused slot. A +tracking id not previously present is considered new, and a tracking id no +longer present is considered removed. Since only changes are propagated, +the full state of each initiated contact has to reside in the receiving +end. Upon receiving an MT event, one simply updates the appropriate +attribute of the current slot. + +Some devices identify and/or track more contacts than they can report to the +driver. A driver for such a device should associate one type B slot with each +contact that is reported by the hardware. Whenever the identity of the +contact associated with a slot changes, the driver should invalidate that +slot by changing its ABS_MT_TRACKING_ID. If the hardware signals that it is +tracking more contacts than it is currently reporting, the driver should use +a BTN_TOOL_*TAP event to inform userspace of the total number of contacts +being tracked by the hardware at that moment. The driver should do this by +explicitly sending the corresponding BTN_TOOL_*TAP event and setting +use_count to false when calling input_mt_report_pointer_emulation(). +The driver should only advertise as many slots as the hardware can report. +Userspace can detect that a driver can report more total contacts than slots +by noting that the largest supported BTN_TOOL_*TAP event is larger than the +total number of type B slots reported in the absinfo for the ABS_MT_SLOT axis. + +The minimum value of the ABS_MT_SLOT axis must be 0. + +Protocol Example A +------------------ + +Here is what a minimal event sequence for a two-contact touch would look +like for a type A device:: + + ABS_MT_POSITION_X x[0] + ABS_MT_POSITION_Y y[0] + SYN_MT_REPORT + ABS_MT_POSITION_X x[1] + ABS_MT_POSITION_Y y[1] + SYN_MT_REPORT + SYN_REPORT + +The sequence after moving one of the contacts looks exactly the same; the +raw data for all present contacts are sent between every synchronization +with SYN_REPORT. + +Here is the sequence after lifting the first contact:: + + ABS_MT_POSITION_X x[1] + ABS_MT_POSITION_Y y[1] + SYN_MT_REPORT + SYN_REPORT + +And here is the sequence after lifting the second contact:: + + SYN_MT_REPORT + SYN_REPORT + +If the driver reports one of BTN_TOUCH or ABS_PRESSURE in addition to the +ABS_MT events, the last SYN_MT_REPORT event may be omitted. Otherwise, the +last SYN_REPORT will be dropped by the input core, resulting in no +zero-contact event reaching userland. + + +Protocol Example B +------------------ + +Here is what a minimal event sequence for a two-contact touch would look +like for a type B device:: + + ABS_MT_SLOT 0 + ABS_MT_TRACKING_ID 45 + ABS_MT_POSITION_X x[0] + ABS_MT_POSITION_Y y[0] + ABS_MT_SLOT 1 + ABS_MT_TRACKING_ID 46 + ABS_MT_POSITION_X x[1] + ABS_MT_POSITION_Y y[1] + SYN_REPORT + +Here is the sequence after moving contact 45 in the x direction:: + + ABS_MT_SLOT 0 + ABS_MT_POSITION_X x[0] + SYN_REPORT + +Here is the sequence after lifting the contact in slot 0:: + + ABS_MT_TRACKING_ID -1 + SYN_REPORT + +The slot being modified is already 0, so the ABS_MT_SLOT is omitted. The +message removes the association of slot 0 with contact 45, thereby +destroying contact 45 and freeing slot 0 to be reused for another contact. + +Finally, here is the sequence after lifting the second contact:: + + ABS_MT_SLOT 1 + ABS_MT_TRACKING_ID -1 + SYN_REPORT + + +Event Usage +----------- + +A set of ABS_MT events with the desired properties is defined. The events +are divided into categories, to allow for partial implementation. The +minimum set consists of ABS_MT_POSITION_X and ABS_MT_POSITION_Y, which +allows for multiple contacts to be tracked. If the device supports it, the +ABS_MT_TOUCH_MAJOR and ABS_MT_WIDTH_MAJOR may be used to provide the size +of the contact area and approaching tool, respectively. + +The TOUCH and WIDTH parameters have a geometrical interpretation; imagine +looking through a window at someone gently holding a finger against the +glass. You will see two regions, one inner region consisting of the part +of the finger actually touching the glass, and one outer region formed by +the perimeter of the finger. The center of the touching region (a) is +ABS_MT_POSITION_X/Y and the center of the approaching finger (b) is +ABS_MT_TOOL_X/Y. The touch diameter is ABS_MT_TOUCH_MAJOR and the finger +diameter is ABS_MT_WIDTH_MAJOR. Now imagine the person pressing the finger +harder against the glass. The touch region will increase, and in general, +the ratio ABS_MT_TOUCH_MAJOR / ABS_MT_WIDTH_MAJOR, which is always smaller +than unity, is related to the contact pressure. For pressure-based devices, +ABS_MT_PRESSURE may be used to provide the pressure on the contact area +instead. Devices capable of contact hovering can use ABS_MT_DISTANCE to +indicate the distance between the contact and the surface. + +:: + + + Linux MT Win8 + __________ _______________________ + / \ | | + / \ | | + / ____ \ | | + / / \ \ | | + \ \ a \ \ | a | + \ \____/ \ | | + \ \ | | + \ b \ | b | + \ \ | | + \ \ | | + \ \ | | + \ / | | + \ / | | + \ / | | + \__________/ |_______________________| + + +In addition to the MAJOR parameters, the oval shape of the touch and finger +regions can be described by adding the MINOR parameters, such that MAJOR +and MINOR are the major and minor axis of an ellipse. The orientation of +the touch ellipse can be described with the ORIENTATION parameter, and the +direction of the finger ellipse is given by the vector (a - b). + +For type A devices, further specification of the touch shape is possible +via ABS_MT_BLOB_ID. + +The ABS_MT_TOOL_TYPE may be used to specify whether the touching tool is a +finger or a pen or something else. Finally, the ABS_MT_TRACKING_ID event +may be used to track identified contacts over time [#f5]_. + +In the type B protocol, ABS_MT_TOOL_TYPE and ABS_MT_TRACKING_ID are +implicitly handled by input core; drivers should instead call +input_mt_report_slot_state(). + + +Event Semantics +--------------- + +ABS_MT_TOUCH_MAJOR + The length of the major axis of the contact. The length should be given in + surface units. If the surface has an X times Y resolution, the largest + possible value of ABS_MT_TOUCH_MAJOR is sqrt(X^2 + Y^2), the diagonal [#f4]_. + +ABS_MT_TOUCH_MINOR + The length, in surface units, of the minor axis of the contact. If the + contact is circular, this event can be omitted [#f4]_. + +ABS_MT_WIDTH_MAJOR + The length, in surface units, of the major axis of the approaching + tool. This should be understood as the size of the tool itself. The + orientation of the contact and the approaching tool are assumed to be the + same [#f4]_. + +ABS_MT_WIDTH_MINOR + The length, in surface units, of the minor axis of the approaching + tool. Omit if circular [#f4]_. + + The above four values can be used to derive additional information about + the contact. The ratio ABS_MT_TOUCH_MAJOR / ABS_MT_WIDTH_MAJOR approximates + the notion of pressure. The fingers of the hand and the palm all have + different characteristic widths. + +ABS_MT_PRESSURE + The pressure, in arbitrary units, on the contact area. May be used instead + of TOUCH and WIDTH for pressure-based devices or any device with a spatial + signal intensity distribution. + + If the resolution is zero, the pressure data is in arbitrary units. + If the resolution is non-zero, the pressure data is in units/gram. See + :ref:`input-event-codes` for details. + +ABS_MT_DISTANCE + The distance, in surface units, between the contact and the surface. Zero + distance means the contact is touching the surface. A positive number means + the contact is hovering above the surface. + +ABS_MT_ORIENTATION + The orientation of the touching ellipse. The value should describe a signed + quarter of a revolution clockwise around the touch center. The signed value + range is arbitrary, but zero should be returned for an ellipse aligned with + the Y axis (north) of the surface, a negative value when the ellipse is + turned to the left, and a positive value when the ellipse is turned to the + right. When aligned with the X axis in the positive direction, the range + max should be returned; when aligned with the X axis in the negative + direction, the range -max should be returned. + + Touch ellipses are symmetrical by default. For devices capable of true 360 + degree orientation, the reported orientation must exceed the range max to + indicate more than a quarter of a revolution. For an upside-down finger, + range max * 2 should be returned. + + Orientation can be omitted if the touch area is circular, or if the + information is not available in the kernel driver. Partial orientation + support is possible if the device can distinguish between the two axes, but + not (uniquely) any values in between. In such cases, the range of + ABS_MT_ORIENTATION should be [0, 1] [#f4]_. + +ABS_MT_POSITION_X + The surface X coordinate of the center of the touching ellipse. + +ABS_MT_POSITION_Y + The surface Y coordinate of the center of the touching ellipse. + +ABS_MT_TOOL_X + The surface X coordinate of the center of the approaching tool. Omit if + the device cannot distinguish between the intended touch point and the + tool itself. + +ABS_MT_TOOL_Y + The surface Y coordinate of the center of the approaching tool. Omit if the + device cannot distinguish between the intended touch point and the tool + itself. + + The four position values can be used to separate the position of the touch + from the position of the tool. If both positions are present, the major + tool axis points towards the touch point [#f1]_. Otherwise, the tool axes are + aligned with the touch axes. + +ABS_MT_TOOL_TYPE + The type of approaching tool. A lot of kernel drivers cannot distinguish + between different tool types, such as a finger or a pen. In such cases, the + event should be omitted. The protocol currently mainly supports + MT_TOOL_FINGER, MT_TOOL_PEN, and MT_TOOL_PALM [#f2]_. + For type B devices, this event is handled by input core; drivers should + instead use input_mt_report_slot_state(). A contact's ABS_MT_TOOL_TYPE may + change over time while still touching the device, because the firmware may + not be able to determine which tool is being used when it first appears. + +ABS_MT_BLOB_ID + The BLOB_ID groups several packets together into one arbitrarily shaped + contact. The sequence of points forms a polygon which defines the shape of + the contact. This is a low-level anonymous grouping for type A devices, and + should not be confused with the high-level trackingID [#f5]_. Most type A + devices do not have blob capability, so drivers can safely omit this event. + +ABS_MT_TRACKING_ID + The TRACKING_ID identifies an initiated contact throughout its life cycle + [#f5]_. The value range of the TRACKING_ID should be large enough to ensure + unique identification of a contact maintained over an extended period of + time. For type B devices, this event is handled by input core; drivers + should instead use input_mt_report_slot_state(). + + +Event Computation +----------------- + +The flora of different hardware unavoidably leads to some devices fitting +better to the MT protocol than others. To simplify and unify the mapping, +this section gives recipes for how to compute certain events. + +For devices reporting contacts as rectangular shapes, signed orientation +cannot be obtained. Assuming X and Y are the lengths of the sides of the +touching rectangle, here is a simple formula that retains the most +information possible:: + + ABS_MT_TOUCH_MAJOR := max(X, Y) + ABS_MT_TOUCH_MINOR := min(X, Y) + ABS_MT_ORIENTATION := bool(X > Y) + +The range of ABS_MT_ORIENTATION should be set to [0, 1], to indicate that +the device can distinguish between a finger along the Y axis (0) and a +finger along the X axis (1). + +For Win8 devices with both T and C coordinates, the position mapping is:: + + ABS_MT_POSITION_X := T_X + ABS_MT_POSITION_Y := T_Y + ABS_MT_TOOL_X := C_X + ABS_MT_TOOL_Y := C_Y + +Unfortunately, there is not enough information to specify both the touching +ellipse and the tool ellipse, so one has to resort to approximations. One +simple scheme, which is compatible with earlier usage, is:: + + ABS_MT_TOUCH_MAJOR := min(X, Y) + ABS_MT_TOUCH_MINOR := <not used> + ABS_MT_ORIENTATION := <not used> + ABS_MT_WIDTH_MAJOR := min(X, Y) + distance(T, C) + ABS_MT_WIDTH_MINOR := min(X, Y) + +Rationale: We have no information about the orientation of the touching +ellipse, so approximate it with an inscribed circle instead. The tool +ellipse should align with the vector (T - C), so the diameter must +increase with distance(T, C). Finally, assume that the touch diameter is +equal to the tool thickness, and we arrive at the formulas above. + +Finger Tracking +--------------- + +The process of finger tracking, i.e., to assign a unique trackingID to each +initiated contact on the surface, is a Euclidian Bipartite Matching +problem. At each event synchronization, the set of actual contacts is +matched to the set of contacts from the previous synchronization. A full +implementation can be found in [#f3]_. + + +Gestures +-------- + +In the specific application of creating gesture events, the TOUCH and WIDTH +parameters can be used to, e.g., approximate finger pressure or distinguish +between index finger and thumb. With the addition of the MINOR parameters, +one can also distinguish between a sweeping finger and a pointing finger, +and with ORIENTATION, one can detect twisting of fingers. + + +Notes +----- + +In order to stay compatible with existing applications, the data reported +in a finger packet must not be recognized as single-touch events. + +For type A devices, all finger data bypasses input filtering, since +subsequent events of the same type refer to different fingers. + +.. [#f1] Also, the difference (TOOL_X - POSITION_X) can be used to model tilt. +.. [#f2] The list can of course be extended. +.. [#f3] The mtdev project: http://bitmath.org/code/mtdev/. +.. [#f4] See the section on event computation. +.. [#f5] See the section on finger tracking. diff --git a/Documentation/input/notifier.rst b/Documentation/input/notifier.rst new file mode 100644 index 000000000..824379399 --- /dev/null +++ b/Documentation/input/notifier.rst @@ -0,0 +1,55 @@ +================= +Keyboard notifier +================= + +One can use register_keyboard_notifier to get called back on keyboard +events (see kbd_keycode() function for details). The passed structure is +keyboard_notifier_param (see <linux/keyboard.h>): + +- 'vc' always provide the VC for which the keyboard event applies; +- 'down' is 1 for a key press event, 0 for a key release; +- 'shift' is the current modifier state, mask bit indexes are KG_*; +- 'ledstate' is the current LED state; +- 'value' depends on the type of event. + +- KBD_KEYCODE events are always sent before other events, value is the keycode. +- KBD_UNBOUND_KEYCODE events are sent if the keycode is not bound to a keysym. + value is the keycode. +- KBD_UNICODE events are sent if the keycode -> keysym translation produced a + unicode character. value is the unicode value. +- KBD_KEYSYM events are sent if the keycode -> keysym translation produced a + non-unicode character. value is the keysym. +- KBD_POST_KEYSYM events are sent after the treatment of non-unicode keysyms. + That permits one to inspect the resulting LEDs for instance. + +For each kind of event but the last, the callback may return NOTIFY_STOP in +order to "eat" the event: the notify loop is stopped and the keyboard event is +dropped. + +In a rough C snippet, we have:: + + kbd_keycode(keycode) { + ... + params.value = keycode; + if (notifier_call_chain(KBD_KEYCODE,¶ms) == NOTIFY_STOP) + || !bound) { + notifier_call_chain(KBD_UNBOUND_KEYCODE,¶ms); + return; + } + + if (unicode) { + param.value = unicode; + if (notifier_call_chain(KBD_UNICODE,¶ms) == NOTIFY_STOP) + return; + emit unicode; + return; + } + + params.value = keysym; + if (notifier_call_chain(KBD_KEYSYM,¶ms) == NOTIFY_STOP) + return; + apply keysym; + notifier_call_chain(KBD_POST_KEYSYM,¶ms); + } + +.. note:: This notifier is usually called from interrupt context. diff --git a/Documentation/input/shape.svg b/Documentation/input/shape.svg new file mode 100644 index 000000000..fc0af44db --- /dev/null +++ b/Documentation/input/shape.svg @@ -0,0 +1,39 @@ +<svg width="7.95in" height="3.70in" version="1.1" viewBox="1956 1041 9354.492 4306.001" xmlns="http://www.w3.org/2000/svg"> + <polyline transform="translate(-121.88 -68.4)" points="4200 3600 4200 3075 4950 2325 7425 2325 8250 3150 8250 3600" fill="none" stroke="#000" stroke-width="15"/> + <polyline transform="translate(-121.88 -68.4)" points="4200 3675 4200 5400" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="8250 3675 8250 5400" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="3675 3600 8700 3600" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="8775 3600 10200 3600" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="8325 3150 9075 3150" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="7500 2325 10200 2325" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="3600 3600 3e3 3600" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="4125 3075 3e3 3075" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="4217 5400 8158 5400" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="8053 5430 8173 5400 8053 5370" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="4322 5370 4202 5400 4322 5430" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="10125 2342 10125 3583" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="10095 3478 10125 3598 10155 3478" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="10155 2447 10125 2327 10095 2447" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="3e3 3167 3e3 3583" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="2970 3478 3e3 3598 3030 3478" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="3030 3272 3e3 3152 2970 3272" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="9075 3167 9075 3583" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="9045 3478 9075 3598 9105 3478" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="9105 3272 9075 3152 9045 3272" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="4950 2325 4950 1200" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="7425 2325 7425 1200" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="4200 3075 4200 2400 3600 1800 3600 1200" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="8250 3150 8250 2475 8775 1950 8775 1200" fill="none" stroke="#000" stroke-dasharray="40, 40" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="3617 1275 4933 1275" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="4828 1305 4948 1275 4828 1245" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="3722 1245 3602 1275 3722 1305" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="7442 1275 8683 1275" fill="none" stroke="#000" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="8578 1305 8698 1275 8578 1245" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <polyline transform="translate(-121.88 -68.4)" points="7547 1245 7427 1275 7547 1305" fill="none" stroke="#000" stroke-miterlimit="8" stroke-width="7"/> + <text x="5953.125" y="5256.6001" fill="#000000" font-family="sans-serif" font-size="144px" stroke-width=".025in" text-anchor="middle" xml:space="preserve">Effect duration</text> + <text x="10078.125" y="2931.5999" fill="#000000" font-family="sans-serif" font-size="144px" stroke-width=".025in" xml:space="preserve">Effect magnitude</text> + <text x="9028.125" y="3381.5999" fill="#000000" font-family="sans-serif" font-size="144px" stroke-width=".025in" xml:space="preserve">Fade level</text> + <text x="4153.125" y="1131.6" fill="#000000" font-family="sans-serif" font-size="144px" stroke-width=".025in" text-anchor="middle" xml:space="preserve">Attack length</text> + <text x="8053.125" y="1131.6" fill="#000000" font-family="sans-serif" font-size="144px" stroke-width=".025in" text-anchor="middle" xml:space="preserve">Fade length</text> + <text x="2803.125" y="3306.5999" fill="#000000" font-family="sans-serif" font-size="144px" stroke-width=".025in" text-anchor="end" xml:space="preserve">Attack level</text> +</svg> diff --git a/Documentation/input/uinput.rst b/Documentation/input/uinput.rst new file mode 100644 index 000000000..30fe80e32 --- /dev/null +++ b/Documentation/input/uinput.rst @@ -0,0 +1,245 @@ +============= +uinput module +============= + +Introduction +============ + +uinput is a kernel module that makes it possible to emulate input devices +from userspace. By writing to /dev/uinput (or /dev/input/uinput) device, a +process can create a virtual input device with specific capabilities. Once +this virtual device is created, the process can send events through it, +that will be delivered to userspace and in-kernel consumers. + +Interface +========= + +:: + + linux/uinput.h + +The uinput header defines ioctls to create, set up, and destroy virtual +devices. + +libevdev +======== + +libevdev is a wrapper library for evdev devices that provides interfaces to +create uinput devices and send events. libevdev is less error-prone than +accessing uinput directly, and should be considered for new software. + +For examples and more information about libevdev: +https://www.freedesktop.org/software/libevdev/doc/latest/ + +Examples +======== + +Keyboard events +--------------- + +This first example shows how to create a new virtual device, and how to +send a key event. All default imports and error handlers were removed for +the sake of simplicity. + +.. code-block:: c + + #include <linux/uinput.h> + + void emit(int fd, int type, int code, int val) + { + struct input_event ie; + + ie.type = type; + ie.code = code; + ie.value = val; + /* timestamp values below are ignored */ + ie.time.tv_sec = 0; + ie.time.tv_usec = 0; + + write(fd, &ie, sizeof(ie)); + } + + int main(void) + { + struct uinput_setup usetup; + + int fd = open("/dev/uinput", O_WRONLY | O_NONBLOCK); + + + /* + * The ioctls below will enable the device that is about to be + * created, to pass key events, in this case the space key. + */ + ioctl(fd, UI_SET_EVBIT, EV_KEY); + ioctl(fd, UI_SET_KEYBIT, KEY_SPACE); + + memset(&usetup, 0, sizeof(usetup)); + usetup.id.bustype = BUS_USB; + usetup.id.vendor = 0x1234; /* sample vendor */ + usetup.id.product = 0x5678; /* sample product */ + strcpy(usetup.name, "Example device"); + + ioctl(fd, UI_DEV_SETUP, &usetup); + ioctl(fd, UI_DEV_CREATE); + + /* + * On UI_DEV_CREATE the kernel will create the device node for this + * device. We are inserting a pause here so that userspace has time + * to detect, initialize the new device, and can start listening to + * the event, otherwise it will not notice the event we are about + * to send. This pause is only needed in our example code! + */ + sleep(1); + + /* Key press, report the event, send key release, and report again */ + emit(fd, EV_KEY, KEY_SPACE, 1); + emit(fd, EV_SYN, SYN_REPORT, 0); + emit(fd, EV_KEY, KEY_SPACE, 0); + emit(fd, EV_SYN, SYN_REPORT, 0); + + /* + * Give userspace some time to read the events before we destroy the + * device with UI_DEV_DESTROY. + */ + sleep(1); + + ioctl(fd, UI_DEV_DESTROY); + close(fd); + + return 0; + } + +Mouse movements +--------------- + +This example shows how to create a virtual device that behaves like a physical +mouse. + +.. code-block:: c + + #include <linux/uinput.h> + + /* emit function is identical to of the first example */ + + int main(void) + { + struct uinput_setup usetup; + int i = 50; + + int fd = open("/dev/uinput", O_WRONLY | O_NONBLOCK); + + /* enable mouse button left and relative events */ + ioctl(fd, UI_SET_EVBIT, EV_KEY); + ioctl(fd, UI_SET_KEYBIT, BTN_LEFT); + + ioctl(fd, UI_SET_EVBIT, EV_REL); + ioctl(fd, UI_SET_RELBIT, REL_X); + ioctl(fd, UI_SET_RELBIT, REL_Y); + + memset(&usetup, 0, sizeof(usetup)); + usetup.id.bustype = BUS_USB; + usetup.id.vendor = 0x1234; /* sample vendor */ + usetup.id.product = 0x5678; /* sample product */ + strcpy(usetup.name, "Example device"); + + ioctl(fd, UI_DEV_SETUP, &usetup); + ioctl(fd, UI_DEV_CREATE); + + /* + * On UI_DEV_CREATE the kernel will create the device node for this + * device. We are inserting a pause here so that userspace has time + * to detect, initialize the new device, and can start listening to + * the event, otherwise it will not notice the event we are about + * to send. This pause is only needed in our example code! + */ + sleep(1); + + /* Move the mouse diagonally, 5 units per axis */ + while (i--) { + emit(fd, EV_REL, REL_X, 5); + emit(fd, EV_REL, REL_Y, 5); + emit(fd, EV_SYN, SYN_REPORT, 0); + usleep(15000); + } + + /* + * Give userspace some time to read the events before we destroy the + * device with UI_DEV_DESTROY. + */ + sleep(1); + + ioctl(fd, UI_DEV_DESTROY); + close(fd); + + return 0; + } + + +uinput old interface +-------------------- + +Before uinput version 5, there wasn't a dedicated ioctl to set up a virtual +device. Programs supporting older versions of uinput interface need to fill +a uinput_user_dev structure and write it to the uinput file descriptor to +configure the new uinput device. New code should not use the old interface +but interact with uinput via ioctl calls, or use libevdev. + +.. code-block:: c + + #include <linux/uinput.h> + + /* emit function is identical to of the first example */ + + int main(void) + { + struct uinput_user_dev uud; + int version, rc, fd; + + fd = open("/dev/uinput", O_WRONLY | O_NONBLOCK); + rc = ioctl(fd, UI_GET_VERSION, &version); + + if (rc == 0 && version >= 5) { + /* use UI_DEV_SETUP */ + return 0; + } + + /* + * The ioctls below will enable the device that is about to be + * created, to pass key events, in this case the space key. + */ + ioctl(fd, UI_SET_EVBIT, EV_KEY); + ioctl(fd, UI_SET_KEYBIT, KEY_SPACE); + + memset(&uud, 0, sizeof(uud)); + snprintf(uud.name, UINPUT_MAX_NAME_SIZE, "uinput old interface"); + write(fd, &uud, sizeof(uud)); + + ioctl(fd, UI_DEV_CREATE); + + /* + * On UI_DEV_CREATE the kernel will create the device node for this + * device. We are inserting a pause here so that userspace has time + * to detect, initialize the new device, and can start listening to + * the event, otherwise it will not notice the event we are about + * to send. This pause is only needed in our example code! + */ + sleep(1); + + /* Key press, report the event, send key release, and report again */ + emit(fd, EV_KEY, KEY_SPACE, 1); + emit(fd, EV_SYN, SYN_REPORT, 0); + emit(fd, EV_KEY, KEY_SPACE, 0); + emit(fd, EV_SYN, SYN_REPORT, 0); + + /* + * Give userspace some time to read the events before we destroy the + * device with UI_DEV_DESTROY. + */ + sleep(1); + + ioctl(fd, UI_DEV_DESTROY); + + close(fd); + return 0; + } + diff --git a/Documentation/input/userio.rst b/Documentation/input/userio.rst new file mode 100644 index 000000000..f780c7793 --- /dev/null +++ b/Documentation/input/userio.rst @@ -0,0 +1,85 @@ +.. include:: <isonum.txt> + +=================== +The userio Protocol +=================== + + +:Copyright: |copy| 2015 Stephen Chandler Paul <thatslyude@gmail.com> + +Sponsored by Red Hat + + +Introduction +============= + +This module is intended to try to make the lives of input driver developers +easier by allowing them to test various serio devices (mainly the various +touchpads found on laptops) without having to have the physical device in front +of them. userio accomplishes this by allowing any privileged userspace program +to directly interact with the kernel's serio driver and control a virtual serio +port from there. + +Usage overview +============== + +In order to interact with the userio kernel module, one simply opens the +/dev/userio character device in their applications. Commands are sent to the +kernel module by writing to the device, and any data received from the serio +driver is read as-is from the /dev/userio device. All of the structures and +macros you need to interact with the device are defined in <linux/userio.h> and +<linux/serio.h>. + +Command Structure +================= + +The struct used for sending commands to /dev/userio is as follows:: + + struct userio_cmd { + __u8 type; + __u8 data; + }; + +``type`` describes the type of command that is being sent. This can be any one +of the USERIO_CMD macros defined in <linux/userio.h>. ``data`` is the argument +that goes along with the command. In the event that the command doesn't have an +argument, this field can be left untouched and will be ignored by the kernel. +Each command should be sent by writing the struct directly to the character +device. In the event that the command you send is invalid, an error will be +returned by the character device and a more descriptive error will be printed +to the kernel log. Only one command can be sent at a time, any additional data +written to the character device after the initial command will be ignored. + +To close the virtual serio port, just close /dev/userio. + +Commands +======== + +USERIO_CMD_REGISTER +~~~~~~~~~~~~~~~~~~~ + +Registers the port with the serio driver and begins transmitting data back and +forth. Registration can only be performed once a port type is set with +USERIO_CMD_SET_PORT_TYPE. Has no argument. + +USERIO_CMD_SET_PORT_TYPE +~~~~~~~~~~~~~~~~~~~~~~~~ + +Sets the type of port we're emulating, where ``data`` is the port type being +set. Can be any of the macros from <linux/serio.h>. For example: SERIO_8042 +would set the port type to be a normal PS/2 port. + +USERIO_CMD_SEND_INTERRUPT +~~~~~~~~~~~~~~~~~~~~~~~~~ + +Sends an interrupt through the virtual serio port to the serio driver, where +``data`` is the interrupt data being sent. + +Userspace tools +=============== + +The userio userspace tools are able to record PS/2 devices using some of the +debugging information from i8042, and play back the devices on /dev/userio. The +latest version of these tools can be found at: + + https://github.com/Lyude/ps2emu |
