diff options
Diffstat (limited to 'arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts')
| -rw-r--r-- | arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 580 |
1 files changed, 580 insertions, 0 deletions
diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts new file mode 100644 index 000000000..d61a297a2 --- /dev/null +++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts @@ -0,0 +1,580 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * dts file for Xilinx ZynqMP ZCU100 revC + * + * (C) Copyright 2016 - 2021, Xilinx, Inc. + * + * Michal Simek <michal.simek@xilinx.com> + * Nathalie Chan King Choy + */ + +/dts-v1/; + +#include "zynqmp.dtsi" +#include "zynqmp-clk-ccf.dtsi" +#include <dt-bindings/input/input.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/pinctrl-zynqmp.h> +#include <dt-bindings/phy/phy.h> + +/ { + model = "ZynqMP ZCU100 RevC"; + compatible = "xlnx,zynqmp-zcu100-revC", "xlnx,zynqmp-zcu100", "xlnx,zynqmp"; + + aliases { + i2c0 = &i2c1; + rtc0 = &rtc; + serial0 = &uart1; + serial1 = &uart0; + serial2 = &dcc; + spi0 = &spi0; + spi1 = &spi1; + usb0 = &usb0; + usb1 = &usb1; + mmc0 = &sdhci0; + mmc1 = &sdhci1; + }; + + chosen { + bootargs = "earlycon"; + stdout-path = "serial0:115200n8"; + }; + + memory@0 { + device_type = "memory"; + reg = <0x0 0x0 0x0 0x80000000>; + }; + + gpio-keys { + compatible = "gpio-keys"; + autorepeat; + switch-4 { + label = "sw4"; + gpios = <&gpio 23 GPIO_ACTIVE_LOW>; + linux,code = <KEY_POWER>; + wakeup-source; + autorepeat; + }; + }; + + leds { + compatible = "gpio-leds"; + led-ds2 { + label = "ds2"; + gpios = <&gpio 20 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + led-ds3 { + label = "ds3"; + gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0tx"; /* WLAN tx */ + default-state = "off"; + }; + + led-ds4 { + label = "ds4"; + gpios = <&gpio 18 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "phy0rx"; /* WLAN rx */ + default-state = "off"; + }; + + led-ds5 { + label = "ds5"; + gpios = <&gpio 17 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "bluetooth-power"; + }; + + vbus-det { /* U5 USB5744 VBUS detection via MIO25 */ + label = "vbus_det"; + gpios = <&gpio 25 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + wmmcsdio_fixed: fixedregulator-mmcsdio { + compatible = "regulator-fixed"; + regulator-name = "wmmcsdio_fixed"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + regulator-boot-on; + }; + + sdio_pwrseq: sdio-pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&gpio 7 GPIO_ACTIVE_LOW>; /* WIFI_EN */ + post-power-on-delay-ms = <10>; + }; + + ina226 { + compatible = "iio-hwmon"; + io-channels = <&u35 0>, <&u35 1>, <&u35 2>, <&u35 3>; + }; + + si5335_0: si5335_0 { /* clk0_usb - u23 */ + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <26000000>; + }; + + si5335_1: si5335_1 { /* clk1_dp - u23 */ + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <27000000>; + }; +}; + +&dcc { + status = "okay"; +}; + +&gpio { + status = "okay"; + gpio-line-names = "UART1_TX", "UART1_RX", "UART0_RX", "UART0_TX", "I2C1_SCL", + "I2C1_SDA", "SPI1_SCLK", "WLAN_EN", "BT_EN", "SPI1_CS", + "SPI1_MISO", "SPI1_MOSI", "I2C_MUX_RESET", "SD0_DAT0", "SD0_DAT1", + "SD0_DAT2", "SD0_DAT3", "PS_LED3", "PS_LED2", "PS_LED1", + "PS_LED0", "SD0_CMD", "SD0_CLK", "GPIO_PB", "SD0_DETECT", + "VBUS_DET", "POWER_INT", "DP_AUX", "DP_HPD", "DP_OE", + "DP_AUX_IN", "INA226_ALERT", "PS_FP_PWR_EN", "PL_PWR_EN", "POWER_KILL", + "", "GPIO-A", "GPIO-B", "SPI0_SCLK", "GPIO-C", + "GPIO-D", "SPI0_CS", "SPI0_MISO", "SPI_MOSI", "GPIO-E", + "GPIO-F", "SD1_D0", "SD1_D1", "SD1_D2", "SD1_D3", + "SD1_CMD", "SD1_CLK", "USB0_CLK", "USB0_DIR", "USB0_DATA2", + "USB0_NXT", "USB0_DATA0", "USB0_DATA1", "USB0_STP", "USB0_DATA3", + "USB0_DATA4", "USB0_DATA5", "USB0_DATA6", "USB0_DATA7", "USB1_CLK", + "USB1_DIR", "USB1_DATA2", "USB1_NXT", "USB1_DATA0", "USB1_DATA1", + "USB1_STP", "USB1_DATA3", "USB1_DATA4", "USB1_DATA5", "USB1_DATA6", + "USB_DATA7", "WLAN_IRQ", "PMIC_IRQ", /* MIO end and EMIO start */ + "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", "", "", "", "", "", "", "", + "", "", "", ""; +}; + +&i2c1 { + status = "okay"; + pinctrl-names = "default", "gpio"; + pinctrl-0 = <&pinctrl_i2c1_default>; + pinctrl-1 = <&pinctrl_i2c1_gpio>; + scl-gpios = <&gpio 4 GPIO_ACTIVE_HIGH>; + sda-gpios = <&gpio 5 GPIO_ACTIVE_HIGH>; + clock-frequency = <100000>; + i2c-mux@75 { /* u11 */ + compatible = "nxp,pca9548"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x75>; + i2csw_0: i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + label = "LS-I2C0"; + }; + i2csw_1: i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + label = "LS-I2C1"; + }; + i2csw_2: i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + label = "HS-I2C2"; + }; + i2csw_3: i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + label = "HS-I2C3"; + }; + i2csw_4: i2c@4 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0x4>; + + pmic: pmic@5e { /* Custom TI PMIC u33 */ + compatible = "ti,tps65086"; + reg = <0x5e>; + interrupt-parent = <&gpio>; + interrupts = <77 IRQ_TYPE_LEVEL_LOW>; + #gpio-cells = <2>; + gpio-controller; + }; + }; + i2csw_5: i2c@5 { + #address-cells = <1>; + #size-cells = <0>; + reg = <5>; + /* PS_PMBUS */ + u35: ina226@40 { /* u35 */ + compatible = "ti,ina226"; + #io-channel-cells = <1>; + reg = <0x40>; + shunt-resistor = <10000>; + /* MIO31 is alert which should be routed to PMUFW */ + }; + }; + i2csw_6: i2c@6 { + #address-cells = <1>; + #size-cells = <0>; + reg = <6>; + /* + * Not Connected + */ + }; + i2csw_7: i2c@7 { + #address-cells = <1>; + #size-cells = <0>; + reg = <7>; + /* + * usb5744 (DNP) - U5 + * 100kHz - this is default freq for us + */ + }; + }; +}; + +&pinctrl0 { + status = "okay"; + pinctrl_i2c1_default: i2c1-default { + mux { + groups = "i2c1_1_grp"; + function = "i2c1"; + }; + + conf { + groups = "i2c1_1_grp"; + bias-pull-up; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + }; + + pinctrl_i2c1_gpio: i2c1-gpio { + mux { + groups = "gpio0_4_grp", "gpio0_5_grp"; + function = "gpio0"; + }; + + conf { + groups = "gpio0_4_grp", "gpio0_5_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + }; + + pinctrl_sdhci0_default: sdhci0-default { + mux { + groups = "sdio0_3_grp"; + function = "sdio0"; + }; + + conf { + groups = "sdio0_3_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + bias-disable; + }; + + mux-cd { + groups = "sdio0_cd_0_grp"; + function = "sdio0_cd"; + }; + + conf-cd { + groups = "sdio0_cd_0_grp"; + bias-high-impedance; + bias-pull-up; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + }; + + pinctrl_sdhci1_default: sdhci1-default { + mux { + groups = "sdio1_2_grp"; + function = "sdio1"; + }; + + conf { + groups = "sdio1_2_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + bias-disable; + }; + }; + + pinctrl_spi0_default: spi0-default { + mux { + groups = "spi0_3_grp"; + function = "spi0"; + }; + + conf { + groups = "spi0_3_grp"; + bias-disable; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + + mux-cs { + groups = "spi0_ss_9_grp"; + function = "spi0_ss"; + }; + + conf-cs { + groups = "spi0_ss_9_grp"; + bias-disable; + }; + + }; + + pinctrl_spi1_default: spi1-default { + mux { + groups = "spi1_0_grp"; + function = "spi1"; + }; + + conf { + groups = "spi1_0_grp"; + bias-disable; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + + mux-cs { + groups = "spi1_ss_0_grp"; + function = "spi1_ss"; + }; + + conf-cs { + groups = "spi1_ss_0_grp"; + bias-disable; + }; + + }; + + pinctrl_uart0_default: uart0-default { + mux { + groups = "uart0_0_grp"; + function = "uart0"; + }; + + conf { + groups = "uart0_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + + conf-rx { + pins = "MIO3"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO2"; + bias-disable; + }; + }; + + pinctrl_uart1_default: uart1-default { + mux { + groups = "uart1_0_grp"; + function = "uart1"; + }; + + conf { + groups = "uart1_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + + conf-rx { + pins = "MIO1"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO0"; + bias-disable; + }; + }; + + pinctrl_usb0_default: usb0-default { + mux { + groups = "usb0_0_grp"; + function = "usb0"; + }; + + conf { + groups = "usb0_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + + conf-rx { + pins = "MIO52", "MIO53", "MIO55"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59", + "MIO60", "MIO61", "MIO62", "MIO63"; + bias-disable; + }; + }; + + pinctrl_usb1_default: usb1-default { + mux { + groups = "usb1_0_grp"; + function = "usb1"; + }; + + conf { + groups = "usb1_0_grp"; + slew-rate = <SLEW_RATE_SLOW>; + power-source = <IO_STANDARD_LVCMOS18>; + }; + + conf-rx { + pins = "MIO64", "MIO65", "MIO67"; + bias-high-impedance; + }; + + conf-tx { + pins = "MIO66", "MIO68", "MIO69", "MIO70", "MIO71", + "MIO72", "MIO73", "MIO74", "MIO75"; + bias-disable; + }; + }; +}; + +&psgtr { + status = "okay"; + /* usb3, dp */ + clocks = <&si5335_0>, <&si5335_1>; + clock-names = "ref0", "ref1"; +}; + +&rtc { + status = "okay"; +}; + +/* SD0 only supports 3.3V, no level shifter */ +&sdhci0 { + status = "okay"; + no-1-8-v; + disable-wp; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhci0_default>; + xlnx,mio-bank = <0>; +}; + +&sdhci1 { + status = "okay"; + bus-width = <0x4>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_sdhci1_default>; + xlnx,mio-bank = <0>; + non-removable; + disable-wp; + cap-power-off-card; + mmc-pwrseq = <&sdio_pwrseq>; + vqmmc-supply = <&wmmcsdio_fixed>; + #address-cells = <1>; + #size-cells = <0>; + wlcore: wifi@2 { + compatible = "ti,wl1831"; + reg = <2>; + interrupt-parent = <&gpio>; + interrupts = <76 IRQ_TYPE_EDGE_RISING>; /* MIO76 WLAN_IRQ 1V8 */ + }; +}; + +&spi0 { /* Low Speed connector */ + status = "okay"; + label = "LS-SPI0"; + num-cs = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi0_default>; +}; + +&spi1 { /* High Speed connector */ + status = "okay"; + label = "HS-SPI1"; + num-cs = <1>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_spi1_default>; +}; + +&uart0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart0_default>; + bluetooth { + compatible = "ti,wl1831-st"; + enable-gpios = <&gpio 8 GPIO_ACTIVE_HIGH>; + }; +}; + +&uart1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1_default>; +}; + +/* ULPI SMSC USB3320 */ +&usb0 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb0_default>; + phy-names = "usb3-phy"; + phys = <&psgtr 2 PHY_TYPE_USB3 0 0>; +}; + +&dwc3_0 { + status = "okay"; + dr_mode = "peripheral"; + maximum-speed = "super-speed"; +}; + +/* ULPI SMSC USB3320 */ +&usb1 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb1_default>; + phy-names = "usb3-phy"; + phys = <&psgtr 3 PHY_TYPE_USB3 1 0>; +}; + +&dwc3_1 { + status = "okay"; + dr_mode = "host"; + maximum-speed = "super-speed"; +}; + +&watchdog0 { + status = "okay"; +}; + +&zynqmp_dpdma { + status = "okay"; +}; + +&zynqmp_dpsub { + status = "okay"; + phy-names = "dp-phy0", "dp-phy1"; + phys = <&psgtr 1 PHY_TYPE_DP 0 1>, + <&psgtr 0 PHY_TYPE_DP 1 1>; +}; |