summaryrefslogtreecommitdiffstats
path: root/drivers/media/rc/winbond-cir.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/media/rc/winbond-cir.c')
-rw-r--r--drivers/media/rc/winbond-cir.c1220
1 files changed, 1220 insertions, 0 deletions
diff --git a/drivers/media/rc/winbond-cir.c b/drivers/media/rc/winbond-cir.c
new file mode 100644
index 000000000..25884a799
--- /dev/null
+++ b/drivers/media/rc/winbond-cir.c
@@ -0,0 +1,1220 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * winbond-cir.c - Driver for the Consumer IR functionality of Winbond
+ * SuperI/O chips.
+ *
+ * Currently supports the Winbond WPCD376i chip (PNP id WEC1022), but
+ * could probably support others (Winbond WEC102X, NatSemi, etc)
+ * with minor modifications.
+ *
+ * Original Author: David Härdeman <david@hardeman.nu>
+ * Copyright (C) 2012 Sean Young <sean@mess.org>
+ * Copyright (C) 2009 - 2011 David Härdeman <david@hardeman.nu>
+ *
+ * Dedicated to my daughter Matilda, without whose loving attention this
+ * driver would have been finished in half the time and with a fraction
+ * of the bugs.
+ *
+ * Written using:
+ * o Winbond WPCD376I datasheet helpfully provided by Jesse Barnes at Intel
+ * o NatSemi PC87338/PC97338 datasheet (for the serial port stuff)
+ * o DSDT dumps
+ *
+ * Supported features:
+ * o IR Receive
+ * o IR Transmit
+ * o Wake-On-CIR functionality
+ * o Carrier detection
+ */
+
+#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
+
+#include <linux/module.h>
+#include <linux/pnp.h>
+#include <linux/interrupt.h>
+#include <linux/timer.h>
+#include <linux/leds.h>
+#include <linux/spinlock.h>
+#include <linux/pci_ids.h>
+#include <linux/io.h>
+#include <linux/bitrev.h>
+#include <linux/slab.h>
+#include <linux/wait.h>
+#include <linux/sched.h>
+#include <media/rc-core.h>
+
+#define DRVNAME "winbond-cir"
+
+/* CEIR Wake-Up Registers, relative to data->wbase */
+#define WBCIR_REG_WCEIR_CTL 0x03 /* CEIR Receiver Control */
+#define WBCIR_REG_WCEIR_STS 0x04 /* CEIR Receiver Status */
+#define WBCIR_REG_WCEIR_EV_EN 0x05 /* CEIR Receiver Event Enable */
+#define WBCIR_REG_WCEIR_CNTL 0x06 /* CEIR Receiver Counter Low */
+#define WBCIR_REG_WCEIR_CNTH 0x07 /* CEIR Receiver Counter High */
+#define WBCIR_REG_WCEIR_INDEX 0x08 /* CEIR Receiver Index */
+#define WBCIR_REG_WCEIR_DATA 0x09 /* CEIR Receiver Data */
+#define WBCIR_REG_WCEIR_CSL 0x0A /* CEIR Re. Compare Strlen */
+#define WBCIR_REG_WCEIR_CFG1 0x0B /* CEIR Re. Configuration 1 */
+#define WBCIR_REG_WCEIR_CFG2 0x0C /* CEIR Re. Configuration 2 */
+
+/* CEIR Enhanced Functionality Registers, relative to data->ebase */
+#define WBCIR_REG_ECEIR_CTS 0x00 /* Enhanced IR Control Status */
+#define WBCIR_REG_ECEIR_CCTL 0x01 /* Infrared Counter Control */
+#define WBCIR_REG_ECEIR_CNT_LO 0x02 /* Infrared Counter LSB */
+#define WBCIR_REG_ECEIR_CNT_HI 0x03 /* Infrared Counter MSB */
+#define WBCIR_REG_ECEIR_IREM 0x04 /* Infrared Emitter Status */
+
+/* SP3 Banked Registers, relative to data->sbase */
+#define WBCIR_REG_SP3_BSR 0x03 /* Bank Select, all banks */
+ /* Bank 0 */
+#define WBCIR_REG_SP3_RXDATA 0x00 /* FIFO RX data (r) */
+#define WBCIR_REG_SP3_TXDATA 0x00 /* FIFO TX data (w) */
+#define WBCIR_REG_SP3_IER 0x01 /* Interrupt Enable */
+#define WBCIR_REG_SP3_EIR 0x02 /* Event Identification (r) */
+#define WBCIR_REG_SP3_FCR 0x02 /* FIFO Control (w) */
+#define WBCIR_REG_SP3_MCR 0x04 /* Mode Control */
+#define WBCIR_REG_SP3_LSR 0x05 /* Link Status */
+#define WBCIR_REG_SP3_MSR 0x06 /* Modem Status */
+#define WBCIR_REG_SP3_ASCR 0x07 /* Aux Status and Control */
+ /* Bank 2 */
+#define WBCIR_REG_SP3_BGDL 0x00 /* Baud Divisor LSB */
+#define WBCIR_REG_SP3_BGDH 0x01 /* Baud Divisor MSB */
+#define WBCIR_REG_SP3_EXCR1 0x02 /* Extended Control 1 */
+#define WBCIR_REG_SP3_EXCR2 0x04 /* Extended Control 2 */
+#define WBCIR_REG_SP3_TXFLV 0x06 /* TX FIFO Level */
+#define WBCIR_REG_SP3_RXFLV 0x07 /* RX FIFO Level */
+ /* Bank 3 */
+#define WBCIR_REG_SP3_MRID 0x00 /* Module Identification */
+#define WBCIR_REG_SP3_SH_LCR 0x01 /* LCR Shadow */
+#define WBCIR_REG_SP3_SH_FCR 0x02 /* FCR Shadow */
+ /* Bank 4 */
+#define WBCIR_REG_SP3_IRCR1 0x02 /* Infrared Control 1 */
+ /* Bank 5 */
+#define WBCIR_REG_SP3_IRCR2 0x04 /* Infrared Control 2 */
+ /* Bank 6 */
+#define WBCIR_REG_SP3_IRCR3 0x00 /* Infrared Control 3 */
+#define WBCIR_REG_SP3_SIR_PW 0x02 /* SIR Pulse Width */
+ /* Bank 7 */
+#define WBCIR_REG_SP3_IRRXDC 0x00 /* IR RX Demod Control */
+#define WBCIR_REG_SP3_IRTXMC 0x01 /* IR TX Mod Control */
+#define WBCIR_REG_SP3_RCCFG 0x02 /* CEIR Config */
+#define WBCIR_REG_SP3_IRCFG1 0x04 /* Infrared Config 1 */
+#define WBCIR_REG_SP3_IRCFG4 0x07 /* Infrared Config 4 */
+
+/*
+ * Magic values follow
+ */
+
+/* No interrupts for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
+#define WBCIR_IRQ_NONE 0x00
+/* RX data bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
+#define WBCIR_IRQ_RX 0x01
+/* TX data low bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
+#define WBCIR_IRQ_TX_LOW 0x02
+/* Over/Under-flow bit for WBCIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
+#define WBCIR_IRQ_ERR 0x04
+/* TX data empty bit for WBCEIR_REG_SP3_IER and WBCIR_REG_SP3_EIR */
+#define WBCIR_IRQ_TX_EMPTY 0x20
+/* Led enable/disable bit for WBCIR_REG_ECEIR_CTS */
+#define WBCIR_LED_ENABLE 0x80
+/* RX data available bit for WBCIR_REG_SP3_LSR */
+#define WBCIR_RX_AVAIL 0x01
+/* RX data overrun error bit for WBCIR_REG_SP3_LSR */
+#define WBCIR_RX_OVERRUN 0x02
+/* TX End-Of-Transmission bit for WBCIR_REG_SP3_ASCR */
+#define WBCIR_TX_EOT 0x04
+/* RX disable bit for WBCIR_REG_SP3_ASCR */
+#define WBCIR_RX_DISABLE 0x20
+/* TX data underrun error bit for WBCIR_REG_SP3_ASCR */
+#define WBCIR_TX_UNDERRUN 0x40
+/* Extended mode enable bit for WBCIR_REG_SP3_EXCR1 */
+#define WBCIR_EXT_ENABLE 0x01
+/* Select compare register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */
+#define WBCIR_REGSEL_COMPARE 0x10
+/* Select mask register in WBCIR_REG_WCEIR_INDEX (bits 5 & 6) */
+#define WBCIR_REGSEL_MASK 0x20
+/* Starting address of selected register in WBCIR_REG_WCEIR_INDEX */
+#define WBCIR_REG_ADDR0 0x00
+/* Enable carrier counter */
+#define WBCIR_CNTR_EN 0x01
+/* Reset carrier counter */
+#define WBCIR_CNTR_R 0x02
+/* Invert TX */
+#define WBCIR_IRTX_INV 0x04
+/* Receiver oversampling */
+#define WBCIR_RX_T_OV 0x40
+
+/* Valid banks for the SP3 UART */
+enum wbcir_bank {
+ WBCIR_BANK_0 = 0x00,
+ WBCIR_BANK_1 = 0x80,
+ WBCIR_BANK_2 = 0xE0,
+ WBCIR_BANK_3 = 0xE4,
+ WBCIR_BANK_4 = 0xE8,
+ WBCIR_BANK_5 = 0xEC,
+ WBCIR_BANK_6 = 0xF0,
+ WBCIR_BANK_7 = 0xF4,
+};
+
+/* Supported power-on IR Protocols */
+enum wbcir_protocol {
+ IR_PROTOCOL_RC5 = 0x0,
+ IR_PROTOCOL_NEC = 0x1,
+ IR_PROTOCOL_RC6 = 0x2,
+};
+
+/* Possible states for IR reception */
+enum wbcir_rxstate {
+ WBCIR_RXSTATE_INACTIVE = 0,
+ WBCIR_RXSTATE_ACTIVE,
+ WBCIR_RXSTATE_ERROR
+};
+
+/* Possible states for IR transmission */
+enum wbcir_txstate {
+ WBCIR_TXSTATE_INACTIVE = 0,
+ WBCIR_TXSTATE_ACTIVE,
+ WBCIR_TXSTATE_ERROR
+};
+
+/* Misc */
+#define WBCIR_NAME "Winbond CIR"
+#define WBCIR_ID_FAMILY 0xF1 /* Family ID for the WPCD376I */
+#define WBCIR_ID_CHIP 0x04 /* Chip ID for the WPCD376I */
+#define WAKEUP_IOMEM_LEN 0x10 /* Wake-Up I/O Reg Len */
+#define EHFUNC_IOMEM_LEN 0x10 /* Enhanced Func I/O Reg Len */
+#define SP_IOMEM_LEN 0x08 /* Serial Port 3 (IR) Reg Len */
+
+/* Per-device data */
+struct wbcir_data {
+ spinlock_t spinlock;
+ struct rc_dev *dev;
+ struct led_classdev led;
+
+ unsigned long wbase; /* Wake-Up Baseaddr */
+ unsigned long ebase; /* Enhanced Func. Baseaddr */
+ unsigned long sbase; /* Serial Port Baseaddr */
+ unsigned int irq; /* Serial Port IRQ */
+ u8 irqmask;
+
+ /* RX state */
+ enum wbcir_rxstate rxstate;
+ int carrier_report_enabled;
+ u32 pulse_duration;
+
+ /* TX state */
+ enum wbcir_txstate txstate;
+ u32 txlen;
+ u32 txoff;
+ u32 *txbuf;
+ u8 txmask;
+ u32 txcarrier;
+};
+
+static bool invert; /* default = 0 */
+module_param(invert, bool, 0444);
+MODULE_PARM_DESC(invert, "Invert the signal from the IR receiver");
+
+static bool txandrx; /* default = 0 */
+module_param(txandrx, bool, 0444);
+MODULE_PARM_DESC(txandrx, "Allow simultaneous TX and RX");
+
+
+/*****************************************************************************
+ *
+ * UTILITY FUNCTIONS
+ *
+ *****************************************************************************/
+
+/* Caller needs to hold wbcir_lock */
+static void
+wbcir_set_bits(unsigned long addr, u8 bits, u8 mask)
+{
+ u8 val;
+
+ val = inb(addr);
+ val = ((val & ~mask) | (bits & mask));
+ outb(val, addr);
+}
+
+/* Selects the register bank for the serial port */
+static inline void
+wbcir_select_bank(struct wbcir_data *data, enum wbcir_bank bank)
+{
+ outb(bank, data->sbase + WBCIR_REG_SP3_BSR);
+}
+
+static inline void
+wbcir_set_irqmask(struct wbcir_data *data, u8 irqmask)
+{
+ if (data->irqmask == irqmask)
+ return;
+
+ wbcir_select_bank(data, WBCIR_BANK_0);
+ outb(irqmask, data->sbase + WBCIR_REG_SP3_IER);
+ data->irqmask = irqmask;
+}
+
+static enum led_brightness
+wbcir_led_brightness_get(struct led_classdev *led_cdev)
+{
+ struct wbcir_data *data = container_of(led_cdev,
+ struct wbcir_data,
+ led);
+
+ if (inb(data->ebase + WBCIR_REG_ECEIR_CTS) & WBCIR_LED_ENABLE)
+ return LED_FULL;
+ else
+ return LED_OFF;
+}
+
+static void
+wbcir_led_brightness_set(struct led_classdev *led_cdev,
+ enum led_brightness brightness)
+{
+ struct wbcir_data *data = container_of(led_cdev,
+ struct wbcir_data,
+ led);
+
+ wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CTS,
+ brightness == LED_OFF ? 0x00 : WBCIR_LED_ENABLE,
+ WBCIR_LED_ENABLE);
+}
+
+/* Manchester encodes bits to RC6 message cells (see wbcir_shutdown) */
+static u8
+wbcir_to_rc6cells(u8 val)
+{
+ u8 coded = 0x00;
+ int i;
+
+ val &= 0x0F;
+ for (i = 0; i < 4; i++) {
+ if (val & 0x01)
+ coded |= 0x02 << (i * 2);
+ else
+ coded |= 0x01 << (i * 2);
+ val >>= 1;
+ }
+
+ return coded;
+}
+
+/*****************************************************************************
+ *
+ * INTERRUPT FUNCTIONS
+ *
+ *****************************************************************************/
+
+static void
+wbcir_carrier_report(struct wbcir_data *data)
+{
+ unsigned counter = inb(data->ebase + WBCIR_REG_ECEIR_CNT_LO) |
+ inb(data->ebase + WBCIR_REG_ECEIR_CNT_HI) << 8;
+
+ if (counter > 0 && counter < 0xffff) {
+ struct ir_raw_event ev = {
+ .carrier_report = 1,
+ .carrier = DIV_ROUND_CLOSEST(counter * 1000000u,
+ data->pulse_duration)
+ };
+
+ ir_raw_event_store(data->dev, &ev);
+ }
+
+ /* reset and restart the counter */
+ data->pulse_duration = 0;
+ wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_R,
+ WBCIR_CNTR_EN | WBCIR_CNTR_R);
+ wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_EN,
+ WBCIR_CNTR_EN | WBCIR_CNTR_R);
+}
+
+static void
+wbcir_idle_rx(struct rc_dev *dev, bool idle)
+{
+ struct wbcir_data *data = dev->priv;
+
+ if (!idle && data->rxstate == WBCIR_RXSTATE_INACTIVE)
+ data->rxstate = WBCIR_RXSTATE_ACTIVE;
+
+ if (idle && data->rxstate != WBCIR_RXSTATE_INACTIVE) {
+ data->rxstate = WBCIR_RXSTATE_INACTIVE;
+
+ if (data->carrier_report_enabled)
+ wbcir_carrier_report(data);
+
+ /* Tell hardware to go idle by setting RXINACTIVE */
+ outb(WBCIR_RX_DISABLE, data->sbase + WBCIR_REG_SP3_ASCR);
+ }
+}
+
+static void
+wbcir_irq_rx(struct wbcir_data *data, struct pnp_dev *device)
+{
+ u8 irdata;
+ struct ir_raw_event rawir = {};
+
+ /* Since RXHDLEV is set, at least 8 bytes are in the FIFO */
+ while (inb(data->sbase + WBCIR_REG_SP3_LSR) & WBCIR_RX_AVAIL) {
+ irdata = inb(data->sbase + WBCIR_REG_SP3_RXDATA);
+ if (data->rxstate == WBCIR_RXSTATE_ERROR)
+ continue;
+
+ rawir.duration = ((irdata & 0x7F) + 1) *
+ (data->carrier_report_enabled ? 2 : 10);
+ rawir.pulse = irdata & 0x80 ? false : true;
+
+ if (rawir.pulse)
+ data->pulse_duration += rawir.duration;
+
+ ir_raw_event_store_with_filter(data->dev, &rawir);
+ }
+
+ ir_raw_event_handle(data->dev);
+}
+
+static void
+wbcir_irq_tx(struct wbcir_data *data)
+{
+ unsigned int space;
+ unsigned int used;
+ u8 bytes[16];
+ u8 byte;
+
+ if (!data->txbuf)
+ return;
+
+ switch (data->txstate) {
+ case WBCIR_TXSTATE_INACTIVE:
+ /* TX FIFO empty */
+ space = 16;
+ break;
+ case WBCIR_TXSTATE_ACTIVE:
+ /* TX FIFO low (3 bytes or less) */
+ space = 13;
+ break;
+ case WBCIR_TXSTATE_ERROR:
+ space = 0;
+ break;
+ default:
+ return;
+ }
+
+ /*
+ * TX data is run-length coded in bytes: YXXXXXXX
+ * Y = space (1) or pulse (0)
+ * X = duration, encoded as (X + 1) * 10us (i.e 10 to 1280 us)
+ */
+ for (used = 0; used < space && data->txoff != data->txlen; used++) {
+ if (data->txbuf[data->txoff] == 0) {
+ data->txoff++;
+ continue;
+ }
+ byte = min((u32)0x80, data->txbuf[data->txoff]);
+ data->txbuf[data->txoff] -= byte;
+ byte--;
+ byte |= (data->txoff % 2 ? 0x80 : 0x00); /* pulse/space */
+ bytes[used] = byte;
+ }
+
+ while (data->txoff != data->txlen && data->txbuf[data->txoff] == 0)
+ data->txoff++;
+
+ if (used == 0) {
+ /* Finished */
+ if (data->txstate == WBCIR_TXSTATE_ERROR)
+ /* Clear TX underrun bit */
+ outb(WBCIR_TX_UNDERRUN, data->sbase + WBCIR_REG_SP3_ASCR);
+ wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR);
+ kfree(data->txbuf);
+ data->txbuf = NULL;
+ data->txstate = WBCIR_TXSTATE_INACTIVE;
+ } else if (data->txoff == data->txlen) {
+ /* At the end of transmission, tell the hw before last byte */
+ outsb(data->sbase + WBCIR_REG_SP3_TXDATA, bytes, used - 1);
+ outb(WBCIR_TX_EOT, data->sbase + WBCIR_REG_SP3_ASCR);
+ outb(bytes[used - 1], data->sbase + WBCIR_REG_SP3_TXDATA);
+ wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR |
+ WBCIR_IRQ_TX_EMPTY);
+ } else {
+ /* More data to follow... */
+ outsb(data->sbase + WBCIR_REG_SP3_RXDATA, bytes, used);
+ if (data->txstate == WBCIR_TXSTATE_INACTIVE) {
+ wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR |
+ WBCIR_IRQ_TX_LOW);
+ data->txstate = WBCIR_TXSTATE_ACTIVE;
+ }
+ }
+}
+
+static irqreturn_t
+wbcir_irq_handler(int irqno, void *cookie)
+{
+ struct pnp_dev *device = cookie;
+ struct wbcir_data *data = pnp_get_drvdata(device);
+ unsigned long flags;
+ u8 status;
+
+ spin_lock_irqsave(&data->spinlock, flags);
+ wbcir_select_bank(data, WBCIR_BANK_0);
+ status = inb(data->sbase + WBCIR_REG_SP3_EIR);
+ status &= data->irqmask;
+
+ if (!status) {
+ spin_unlock_irqrestore(&data->spinlock, flags);
+ return IRQ_NONE;
+ }
+
+ if (status & WBCIR_IRQ_ERR) {
+ /* RX overflow? (read clears bit) */
+ if (inb(data->sbase + WBCIR_REG_SP3_LSR) & WBCIR_RX_OVERRUN) {
+ data->rxstate = WBCIR_RXSTATE_ERROR;
+ ir_raw_event_overflow(data->dev);
+ }
+
+ /* TX underflow? */
+ if (inb(data->sbase + WBCIR_REG_SP3_ASCR) & WBCIR_TX_UNDERRUN)
+ data->txstate = WBCIR_TXSTATE_ERROR;
+ }
+
+ if (status & WBCIR_IRQ_RX)
+ wbcir_irq_rx(data, device);
+
+ if (status & (WBCIR_IRQ_TX_LOW | WBCIR_IRQ_TX_EMPTY))
+ wbcir_irq_tx(data);
+
+ spin_unlock_irqrestore(&data->spinlock, flags);
+ return IRQ_HANDLED;
+}
+
+/*****************************************************************************
+ *
+ * RC-CORE INTERFACE FUNCTIONS
+ *
+ *****************************************************************************/
+
+static int
+wbcir_set_carrier_report(struct rc_dev *dev, int enable)
+{
+ struct wbcir_data *data = dev->priv;
+ unsigned long flags;
+
+ spin_lock_irqsave(&data->spinlock, flags);
+
+ if (data->carrier_report_enabled == enable) {
+ spin_unlock_irqrestore(&data->spinlock, flags);
+ return 0;
+ }
+
+ data->pulse_duration = 0;
+ wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL, WBCIR_CNTR_R,
+ WBCIR_CNTR_EN | WBCIR_CNTR_R);
+
+ if (enable && data->dev->idle)
+ wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CCTL,
+ WBCIR_CNTR_EN, WBCIR_CNTR_EN | WBCIR_CNTR_R);
+
+ /* Set a higher sampling resolution if carrier reports are enabled */
+ wbcir_select_bank(data, WBCIR_BANK_2);
+ data->dev->rx_resolution = enable ? 2 : 10;
+ outb(enable ? 0x03 : 0x0f, data->sbase + WBCIR_REG_SP3_BGDL);
+ outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH);
+
+ /* Enable oversampling if carrier reports are enabled */
+ wbcir_select_bank(data, WBCIR_BANK_7);
+ wbcir_set_bits(data->sbase + WBCIR_REG_SP3_RCCFG,
+ enable ? WBCIR_RX_T_OV : 0, WBCIR_RX_T_OV);
+
+ data->carrier_report_enabled = enable;
+ spin_unlock_irqrestore(&data->spinlock, flags);
+
+ return 0;
+}
+
+static int
+wbcir_txcarrier(struct rc_dev *dev, u32 carrier)
+{
+ struct wbcir_data *data = dev->priv;
+ unsigned long flags;
+ u8 val;
+ u32 freq;
+
+ freq = DIV_ROUND_CLOSEST(carrier, 1000);
+ if (freq < 30 || freq > 60)
+ return -EINVAL;
+
+ switch (freq) {
+ case 58:
+ case 59:
+ case 60:
+ val = freq - 58;
+ freq *= 1000;
+ break;
+ case 57:
+ val = freq - 27;
+ freq = 56900;
+ break;
+ default:
+ val = freq - 27;
+ freq *= 1000;
+ break;
+ }
+
+ spin_lock_irqsave(&data->spinlock, flags);
+ if (data->txstate != WBCIR_TXSTATE_INACTIVE) {
+ spin_unlock_irqrestore(&data->spinlock, flags);
+ return -EBUSY;
+ }
+
+ if (data->txcarrier != freq) {
+ wbcir_select_bank(data, WBCIR_BANK_7);
+ wbcir_set_bits(data->sbase + WBCIR_REG_SP3_IRTXMC, val, 0x1F);
+ data->txcarrier = freq;
+ }
+
+ spin_unlock_irqrestore(&data->spinlock, flags);
+ return 0;
+}
+
+static int
+wbcir_txmask(struct rc_dev *dev, u32 mask)
+{
+ struct wbcir_data *data = dev->priv;
+ unsigned long flags;
+ u8 val;
+
+ /* return the number of transmitters */
+ if (mask > 15)
+ return 4;
+
+ /* Four outputs, only one output can be enabled at a time */
+ switch (mask) {
+ case 0x1:
+ val = 0x0;
+ break;
+ case 0x2:
+ val = 0x1;
+ break;
+ case 0x4:
+ val = 0x2;
+ break;
+ case 0x8:
+ val = 0x3;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ spin_lock_irqsave(&data->spinlock, flags);
+ if (data->txstate != WBCIR_TXSTATE_INACTIVE) {
+ spin_unlock_irqrestore(&data->spinlock, flags);
+ return -EBUSY;
+ }
+
+ if (data->txmask != mask) {
+ wbcir_set_bits(data->ebase + WBCIR_REG_ECEIR_CTS, val, 0x0c);
+ data->txmask = mask;
+ }
+
+ spin_unlock_irqrestore(&data->spinlock, flags);
+ return 0;
+}
+
+static int
+wbcir_tx(struct rc_dev *dev, unsigned *b, unsigned count)
+{
+ struct wbcir_data *data = dev->priv;
+ unsigned *buf;
+ unsigned i;
+ unsigned long flags;
+
+ buf = kmalloc_array(count, sizeof(*b), GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ /* Convert values to multiples of 10us */
+ for (i = 0; i < count; i++)
+ buf[i] = DIV_ROUND_CLOSEST(b[i], 10);
+
+ /* Not sure if this is possible, but better safe than sorry */
+ spin_lock_irqsave(&data->spinlock, flags);
+ if (data->txstate != WBCIR_TXSTATE_INACTIVE) {
+ spin_unlock_irqrestore(&data->spinlock, flags);
+ kfree(buf);
+ return -EBUSY;
+ }
+
+ /* Fill the TX fifo once, the irq handler will do the rest */
+ data->txbuf = buf;
+ data->txlen = count;
+ data->txoff = 0;
+ wbcir_irq_tx(data);
+
+ /* We're done */
+ spin_unlock_irqrestore(&data->spinlock, flags);
+ return count;
+}
+
+/*****************************************************************************
+ *
+ * SETUP/INIT/SUSPEND/RESUME FUNCTIONS
+ *
+ *****************************************************************************/
+
+static void
+wbcir_shutdown(struct pnp_dev *device)
+{
+ struct device *dev = &device->dev;
+ struct wbcir_data *data = pnp_get_drvdata(device);
+ struct rc_dev *rc = data->dev;
+ bool do_wake = true;
+ u8 match[11];
+ u8 mask[11];
+ u8 rc6_csl = 0;
+ u8 proto;
+ u32 wake_sc = rc->scancode_wakeup_filter.data;
+ u32 mask_sc = rc->scancode_wakeup_filter.mask;
+ int i;
+
+ memset(match, 0, sizeof(match));
+ memset(mask, 0, sizeof(mask));
+
+ if (!mask_sc || !device_may_wakeup(dev)) {
+ do_wake = false;
+ goto finish;
+ }
+
+ switch (rc->wakeup_protocol) {
+ case RC_PROTO_RC5:
+ /* Mask = 13 bits, ex toggle */
+ mask[0] = (mask_sc & 0x003f);
+ mask[0] |= (mask_sc & 0x0300) >> 2;
+ mask[1] = (mask_sc & 0x1c00) >> 10;
+ if (mask_sc & 0x0040) /* 2nd start bit */
+ match[1] |= 0x10;
+
+ match[0] = (wake_sc & 0x003F); /* 6 command bits */
+ match[0] |= (wake_sc & 0x0300) >> 2; /* 2 address bits */
+ match[1] = (wake_sc & 0x1c00) >> 10; /* 3 address bits */
+ if (!(wake_sc & 0x0040)) /* 2nd start bit */
+ match[1] |= 0x10;
+
+ proto = IR_PROTOCOL_RC5;
+ break;
+
+ case RC_PROTO_NEC:
+ mask[1] = bitrev8(mask_sc);
+ mask[0] = mask[1];
+ mask[3] = bitrev8(mask_sc >> 8);
+ mask[2] = mask[3];
+
+ match[1] = bitrev8(wake_sc);
+ match[0] = ~match[1];
+ match[3] = bitrev8(wake_sc >> 8);
+ match[2] = ~match[3];
+
+ proto = IR_PROTOCOL_NEC;
+ break;
+
+ case RC_PROTO_NECX:
+ mask[1] = bitrev8(mask_sc);
+ mask[0] = mask[1];
+ mask[2] = bitrev8(mask_sc >> 8);
+ mask[3] = bitrev8(mask_sc >> 16);
+
+ match[1] = bitrev8(wake_sc);
+ match[0] = ~match[1];
+ match[2] = bitrev8(wake_sc >> 8);
+ match[3] = bitrev8(wake_sc >> 16);
+
+ proto = IR_PROTOCOL_NEC;
+ break;
+
+ case RC_PROTO_NEC32:
+ mask[0] = bitrev8(mask_sc);
+ mask[1] = bitrev8(mask_sc >> 8);
+ mask[2] = bitrev8(mask_sc >> 16);
+ mask[3] = bitrev8(mask_sc >> 24);
+
+ match[0] = bitrev8(wake_sc);
+ match[1] = bitrev8(wake_sc >> 8);
+ match[2] = bitrev8(wake_sc >> 16);
+ match[3] = bitrev8(wake_sc >> 24);
+
+ proto = IR_PROTOCOL_NEC;
+ break;
+
+ case RC_PROTO_RC6_0:
+ /* Command */
+ match[0] = wbcir_to_rc6cells(wake_sc >> 0);
+ mask[0] = wbcir_to_rc6cells(mask_sc >> 0);
+ match[1] = wbcir_to_rc6cells(wake_sc >> 4);
+ mask[1] = wbcir_to_rc6cells(mask_sc >> 4);
+
+ /* Address */
+ match[2] = wbcir_to_rc6cells(wake_sc >> 8);
+ mask[2] = wbcir_to_rc6cells(mask_sc >> 8);
+ match[3] = wbcir_to_rc6cells(wake_sc >> 12);
+ mask[3] = wbcir_to_rc6cells(mask_sc >> 12);
+
+ /* Header */
+ match[4] = 0x50; /* mode1 = mode0 = 0, ignore toggle */
+ mask[4] = 0xF0;
+ match[5] = 0x09; /* start bit = 1, mode2 = 0 */
+ mask[5] = 0x0F;
+
+ rc6_csl = 44;
+ proto = IR_PROTOCOL_RC6;
+ break;
+
+ case RC_PROTO_RC6_6A_24:
+ case RC_PROTO_RC6_6A_32:
+ case RC_PROTO_RC6_MCE:
+ i = 0;
+
+ /* Command */
+ match[i] = wbcir_to_rc6cells(wake_sc >> 0);
+ mask[i++] = wbcir_to_rc6cells(mask_sc >> 0);
+ match[i] = wbcir_to_rc6cells(wake_sc >> 4);
+ mask[i++] = wbcir_to_rc6cells(mask_sc >> 4);
+
+ /* Address + Toggle */
+ match[i] = wbcir_to_rc6cells(wake_sc >> 8);
+ mask[i++] = wbcir_to_rc6cells(mask_sc >> 8);
+ match[i] = wbcir_to_rc6cells(wake_sc >> 12);
+ mask[i++] = wbcir_to_rc6cells(mask_sc >> 12);
+
+ /* Customer bits 7 - 0 */
+ match[i] = wbcir_to_rc6cells(wake_sc >> 16);
+ mask[i++] = wbcir_to_rc6cells(mask_sc >> 16);
+
+ if (rc->wakeup_protocol == RC_PROTO_RC6_6A_20) {
+ rc6_csl = 52;
+ } else {
+ match[i] = wbcir_to_rc6cells(wake_sc >> 20);
+ mask[i++] = wbcir_to_rc6cells(mask_sc >> 20);
+
+ if (rc->wakeup_protocol == RC_PROTO_RC6_6A_24) {
+ rc6_csl = 60;
+ } else {
+ /* Customer range bit and bits 15 - 8 */
+ match[i] = wbcir_to_rc6cells(wake_sc >> 24);
+ mask[i++] = wbcir_to_rc6cells(mask_sc >> 24);
+ match[i] = wbcir_to_rc6cells(wake_sc >> 28);
+ mask[i++] = wbcir_to_rc6cells(mask_sc >> 28);
+ rc6_csl = 76;
+ }
+ }
+
+ /* Header */
+ match[i] = 0x93; /* mode1 = mode0 = 1, submode = 0 */
+ mask[i++] = 0xFF;
+ match[i] = 0x0A; /* start bit = 1, mode2 = 1 */
+ mask[i++] = 0x0F;
+ proto = IR_PROTOCOL_RC6;
+ break;
+ default:
+ do_wake = false;
+ break;
+ }
+
+finish:
+ if (do_wake) {
+ /* Set compare and compare mask */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX,
+ WBCIR_REGSEL_COMPARE | WBCIR_REG_ADDR0,
+ 0x3F);
+ outsb(data->wbase + WBCIR_REG_WCEIR_DATA, match, 11);
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_INDEX,
+ WBCIR_REGSEL_MASK | WBCIR_REG_ADDR0,
+ 0x3F);
+ outsb(data->wbase + WBCIR_REG_WCEIR_DATA, mask, 11);
+
+ /* RC6 Compare String Len */
+ outb(rc6_csl, data->wbase + WBCIR_REG_WCEIR_CSL);
+
+ /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17);
+
+ /* Clear BUFF_EN, Clear END_EN, Set MATCH_EN */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x01, 0x07);
+
+ /* Set CEIR_EN */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL,
+ (proto << 4) | 0x01, 0x31);
+
+ } else {
+ /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07);
+
+ /* Clear CEIR_EN */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01);
+ }
+
+ /*
+ * ACPI will set the HW disable bit for SP3 which means that the
+ * output signals are left in an undefined state which may cause
+ * spurious interrupts which we need to ignore until the hardware
+ * is reinitialized.
+ */
+ wbcir_set_irqmask(data, WBCIR_IRQ_NONE);
+ disable_irq(data->irq);
+}
+
+/*
+ * Wakeup handling is done on shutdown.
+ */
+static int
+wbcir_set_wakeup_filter(struct rc_dev *rc, struct rc_scancode_filter *filter)
+{
+ return 0;
+}
+
+static int
+wbcir_suspend(struct pnp_dev *device, pm_message_t state)
+{
+ struct wbcir_data *data = pnp_get_drvdata(device);
+ led_classdev_suspend(&data->led);
+ wbcir_shutdown(device);
+ return 0;
+}
+
+static void
+wbcir_init_hw(struct wbcir_data *data)
+{
+ /* Disable interrupts */
+ wbcir_set_irqmask(data, WBCIR_IRQ_NONE);
+
+ /* Set RX_INV, Clear CEIR_EN (needed for the led) */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, invert ? 8 : 0, 0x09);
+
+ /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17);
+
+ /* Clear BUFF_EN, Clear END_EN, Clear MATCH_EN */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07);
+
+ /* Set RC5 cell time to correspond to 36 kHz */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CFG1, 0x4A, 0x7F);
+
+ /* Set IRTX_INV */
+ if (invert)
+ outb(WBCIR_IRTX_INV, data->ebase + WBCIR_REG_ECEIR_CCTL);
+ else
+ outb(0x00, data->ebase + WBCIR_REG_ECEIR_CCTL);
+
+ /*
+ * Clear IR LED, set SP3 clock to 24Mhz, set TX mask to IRTX1,
+ * set SP3_IRRX_SW to binary 01, helpfully not documented
+ */
+ outb(0x10, data->ebase + WBCIR_REG_ECEIR_CTS);
+ data->txmask = 0x1;
+
+ /* Enable extended mode */
+ wbcir_select_bank(data, WBCIR_BANK_2);
+ outb(WBCIR_EXT_ENABLE, data->sbase + WBCIR_REG_SP3_EXCR1);
+
+ /*
+ * Configure baud generator, IR data will be sampled at
+ * a bitrate of: (24Mhz * prescaler) / (divisor * 16).
+ *
+ * The ECIR registers include a flag to change the
+ * 24Mhz clock freq to 48Mhz.
+ *
+ * It's not documented in the specs, but fifo levels
+ * other than 16 seems to be unsupported.
+ */
+
+ /* prescaler 1.0, tx/rx fifo lvl 16 */
+ outb(0x30, data->sbase + WBCIR_REG_SP3_EXCR2);
+
+ /* Set baud divisor to sample every 10 us */
+ outb(0x0f, data->sbase + WBCIR_REG_SP3_BGDL);
+ outb(0x00, data->sbase + WBCIR_REG_SP3_BGDH);
+
+ /* Set CEIR mode */
+ wbcir_select_bank(data, WBCIR_BANK_0);
+ outb(0xC0, data->sbase + WBCIR_REG_SP3_MCR);
+ inb(data->sbase + WBCIR_REG_SP3_LSR); /* Clear LSR */
+ inb(data->sbase + WBCIR_REG_SP3_MSR); /* Clear MSR */
+
+ /* Disable RX demod, enable run-length enc/dec, set freq span */
+ wbcir_select_bank(data, WBCIR_BANK_7);
+ outb(0x90, data->sbase + WBCIR_REG_SP3_RCCFG);
+
+ /* Disable timer */
+ wbcir_select_bank(data, WBCIR_BANK_4);
+ outb(0x00, data->sbase + WBCIR_REG_SP3_IRCR1);
+
+ /* Disable MSR interrupt, clear AUX_IRX, mask RX during TX? */
+ wbcir_select_bank(data, WBCIR_BANK_5);
+ outb(txandrx ? 0x03 : 0x02, data->sbase + WBCIR_REG_SP3_IRCR2);
+
+ /* Disable CRC */
+ wbcir_select_bank(data, WBCIR_BANK_6);
+ outb(0x20, data->sbase + WBCIR_REG_SP3_IRCR3);
+
+ /* Set RX demodulation freq, not really used */
+ wbcir_select_bank(data, WBCIR_BANK_7);
+ outb(0xF2, data->sbase + WBCIR_REG_SP3_IRRXDC);
+
+ /* Set TX modulation, 36kHz, 7us pulse width */
+ outb(0x69, data->sbase + WBCIR_REG_SP3_IRTXMC);
+ data->txcarrier = 36000;
+
+ /* Set invert and pin direction */
+ if (invert)
+ outb(0x10, data->sbase + WBCIR_REG_SP3_IRCFG4);
+ else
+ outb(0x00, data->sbase + WBCIR_REG_SP3_IRCFG4);
+
+ /* Set FIFO thresholds (RX = 8, TX = 3), reset RX/TX */
+ wbcir_select_bank(data, WBCIR_BANK_0);
+ outb(0x97, data->sbase + WBCIR_REG_SP3_FCR);
+
+ /* Clear AUX status bits */
+ outb(0xE0, data->sbase + WBCIR_REG_SP3_ASCR);
+
+ /* Clear RX state */
+ data->rxstate = WBCIR_RXSTATE_INACTIVE;
+ wbcir_idle_rx(data->dev, true);
+
+ /* Clear TX state */
+ if (data->txstate == WBCIR_TXSTATE_ACTIVE) {
+ kfree(data->txbuf);
+ data->txbuf = NULL;
+ data->txstate = WBCIR_TXSTATE_INACTIVE;
+ }
+
+ /* Enable interrupts */
+ wbcir_set_irqmask(data, WBCIR_IRQ_RX | WBCIR_IRQ_ERR);
+}
+
+static int
+wbcir_resume(struct pnp_dev *device)
+{
+ struct wbcir_data *data = pnp_get_drvdata(device);
+
+ wbcir_init_hw(data);
+ enable_irq(data->irq);
+ led_classdev_resume(&data->led);
+
+ return 0;
+}
+
+static int
+wbcir_probe(struct pnp_dev *device, const struct pnp_device_id *dev_id)
+{
+ struct device *dev = &device->dev;
+ struct wbcir_data *data;
+ int err;
+
+ if (!(pnp_port_len(device, 0) == EHFUNC_IOMEM_LEN &&
+ pnp_port_len(device, 1) == WAKEUP_IOMEM_LEN &&
+ pnp_port_len(device, 2) == SP_IOMEM_LEN)) {
+ dev_err(dev, "Invalid resources\n");
+ return -ENODEV;
+ }
+
+ data = kzalloc(sizeof(*data), GFP_KERNEL);
+ if (!data) {
+ err = -ENOMEM;
+ goto exit;
+ }
+
+ pnp_set_drvdata(device, data);
+
+ spin_lock_init(&data->spinlock);
+ data->ebase = pnp_port_start(device, 0);
+ data->wbase = pnp_port_start(device, 1);
+ data->sbase = pnp_port_start(device, 2);
+ data->irq = pnp_irq(device, 0);
+
+ if (data->wbase == 0 || data->ebase == 0 ||
+ data->sbase == 0 || data->irq == -1) {
+ err = -ENODEV;
+ dev_err(dev, "Invalid resources\n");
+ goto exit_free_data;
+ }
+
+ dev_dbg(&device->dev, "Found device (w: 0x%lX, e: 0x%lX, s: 0x%lX, i: %u)\n",
+ data->wbase, data->ebase, data->sbase, data->irq);
+
+ data->led.name = "cir::activity";
+ data->led.default_trigger = "rc-feedback";
+ data->led.brightness_set = wbcir_led_brightness_set;
+ data->led.brightness_get = wbcir_led_brightness_get;
+ err = led_classdev_register(&device->dev, &data->led);
+ if (err)
+ goto exit_free_data;
+
+ data->dev = rc_allocate_device(RC_DRIVER_IR_RAW);
+ if (!data->dev) {
+ err = -ENOMEM;
+ goto exit_unregister_led;
+ }
+
+ data->dev->driver_name = DRVNAME;
+ data->dev->device_name = WBCIR_NAME;
+ data->dev->input_phys = "wbcir/cir0";
+ data->dev->input_id.bustype = BUS_HOST;
+ data->dev->input_id.vendor = PCI_VENDOR_ID_WINBOND;
+ data->dev->input_id.product = WBCIR_ID_FAMILY;
+ data->dev->input_id.version = WBCIR_ID_CHIP;
+ data->dev->map_name = RC_MAP_RC6_MCE;
+ data->dev->s_idle = wbcir_idle_rx;
+ data->dev->s_carrier_report = wbcir_set_carrier_report;
+ data->dev->s_tx_mask = wbcir_txmask;
+ data->dev->s_tx_carrier = wbcir_txcarrier;
+ data->dev->tx_ir = wbcir_tx;
+ data->dev->priv = data;
+ data->dev->dev.parent = &device->dev;
+ data->dev->min_timeout = 1;
+ data->dev->timeout = IR_DEFAULT_TIMEOUT;
+ data->dev->max_timeout = 10 * IR_DEFAULT_TIMEOUT;
+ data->dev->rx_resolution = 2;
+ data->dev->allowed_protocols = RC_PROTO_BIT_ALL_IR_DECODER;
+ data->dev->allowed_wakeup_protocols = RC_PROTO_BIT_NEC |
+ RC_PROTO_BIT_NECX | RC_PROTO_BIT_NEC32 | RC_PROTO_BIT_RC5 |
+ RC_PROTO_BIT_RC6_0 | RC_PROTO_BIT_RC6_6A_20 |
+ RC_PROTO_BIT_RC6_6A_24 | RC_PROTO_BIT_RC6_6A_32 |
+ RC_PROTO_BIT_RC6_MCE;
+ data->dev->wakeup_protocol = RC_PROTO_RC6_MCE;
+ data->dev->scancode_wakeup_filter.data = 0x800f040c;
+ data->dev->scancode_wakeup_filter.mask = 0xffff7fff;
+ data->dev->s_wakeup_filter = wbcir_set_wakeup_filter;
+
+ err = rc_register_device(data->dev);
+ if (err)
+ goto exit_free_rc;
+
+ if (!request_region(data->wbase, WAKEUP_IOMEM_LEN, DRVNAME)) {
+ dev_err(dev, "Region 0x%lx-0x%lx already in use!\n",
+ data->wbase, data->wbase + WAKEUP_IOMEM_LEN - 1);
+ err = -EBUSY;
+ goto exit_unregister_device;
+ }
+
+ if (!request_region(data->ebase, EHFUNC_IOMEM_LEN, DRVNAME)) {
+ dev_err(dev, "Region 0x%lx-0x%lx already in use!\n",
+ data->ebase, data->ebase + EHFUNC_IOMEM_LEN - 1);
+ err = -EBUSY;
+ goto exit_release_wbase;
+ }
+
+ if (!request_region(data->sbase, SP_IOMEM_LEN, DRVNAME)) {
+ dev_err(dev, "Region 0x%lx-0x%lx already in use!\n",
+ data->sbase, data->sbase + SP_IOMEM_LEN - 1);
+ err = -EBUSY;
+ goto exit_release_ebase;
+ }
+
+ err = request_irq(data->irq, wbcir_irq_handler,
+ 0, DRVNAME, device);
+ if (err) {
+ dev_err(dev, "Failed to claim IRQ %u\n", data->irq);
+ err = -EBUSY;
+ goto exit_release_sbase;
+ }
+
+ device_init_wakeup(&device->dev, 1);
+
+ wbcir_init_hw(data);
+
+ return 0;
+
+exit_release_sbase:
+ release_region(data->sbase, SP_IOMEM_LEN);
+exit_release_ebase:
+ release_region(data->ebase, EHFUNC_IOMEM_LEN);
+exit_release_wbase:
+ release_region(data->wbase, WAKEUP_IOMEM_LEN);
+exit_unregister_device:
+ rc_unregister_device(data->dev);
+ data->dev = NULL;
+exit_free_rc:
+ rc_free_device(data->dev);
+exit_unregister_led:
+ led_classdev_unregister(&data->led);
+exit_free_data:
+ kfree(data);
+ pnp_set_drvdata(device, NULL);
+exit:
+ return err;
+}
+
+static void
+wbcir_remove(struct pnp_dev *device)
+{
+ struct wbcir_data *data = pnp_get_drvdata(device);
+
+ /* Disable interrupts */
+ wbcir_set_irqmask(data, WBCIR_IRQ_NONE);
+ free_irq(data->irq, device);
+
+ /* Clear status bits NEC_REP, BUFF, MSG_END, MATCH */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_STS, 0x17, 0x17);
+
+ /* Clear CEIR_EN */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_CTL, 0x00, 0x01);
+
+ /* Clear BUFF_EN, END_EN, MATCH_EN */
+ wbcir_set_bits(data->wbase + WBCIR_REG_WCEIR_EV_EN, 0x00, 0x07);
+
+ rc_unregister_device(data->dev);
+
+ led_classdev_unregister(&data->led);
+
+ /* This is ok since &data->led isn't actually used */
+ wbcir_led_brightness_set(&data->led, LED_OFF);
+
+ release_region(data->wbase, WAKEUP_IOMEM_LEN);
+ release_region(data->ebase, EHFUNC_IOMEM_LEN);
+ release_region(data->sbase, SP_IOMEM_LEN);
+
+ kfree(data);
+
+ pnp_set_drvdata(device, NULL);
+}
+
+static const struct pnp_device_id wbcir_ids[] = {
+ { "WEC1022", 0 },
+ { "", 0 }
+};
+MODULE_DEVICE_TABLE(pnp, wbcir_ids);
+
+static struct pnp_driver wbcir_driver = {
+ .name = DRVNAME,
+ .id_table = wbcir_ids,
+ .probe = wbcir_probe,
+ .remove = wbcir_remove,
+ .suspend = wbcir_suspend,
+ .resume = wbcir_resume,
+ .shutdown = wbcir_shutdown
+};
+
+static int __init
+wbcir_init(void)
+{
+ int ret;
+
+ ret = pnp_register_driver(&wbcir_driver);
+ if (ret)
+ pr_err("Unable to register driver\n");
+
+ return ret;
+}
+
+static void __exit
+wbcir_exit(void)
+{
+ pnp_unregister_driver(&wbcir_driver);
+}
+
+module_init(wbcir_init);
+module_exit(wbcir_exit);
+
+MODULE_AUTHOR("David Härdeman <david@hardeman.nu>");
+MODULE_DESCRIPTION("Winbond SuperI/O Consumer IR Driver");
+MODULE_LICENSE("GPL");