1 files changed, 448 insertions, 0 deletions
diff --git a/drivers/net/ethernet/intel/igc/igc_base.c b/drivers/net/ethernet/intel/igc/igc_base.c
new file mode 100644
index 000000000..a1d815af5
--- /dev/null
+++ b/drivers/net/ethernet/intel/igc/igc_base.c
@@ -0,0 +1,448 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright (c)  2018 Intel Corporation */
+
+#include <linux/delay.h>
+
+#include "igc_hw.h"
+#include "igc_i225.h"
+#include "igc_mac.h"
+#include "igc_base.h"
+#include "igc.h"
+
+/**
+ * igc_reset_hw_base - Reset hardware
+ * @hw: pointer to the HW structure
+ *
+ * This resets the hardware into a known state.  This is a
+ * function pointer entry point called by the api module.
+ */
+static s32 igc_reset_hw_base(struct igc_hw *hw)
+{
+	s32 ret_val;
+	u32 ctrl;
+
+	/* Prevent the PCI-E bus from sticking if there is no TLP connection
+	 * on the last TLP read/write transaction when MAC is reset.
+	 */
+	ret_val = igc_disable_pcie_master(hw);
+	if (ret_val)
+		hw_dbg("PCI-E Master disable polling has failed\n");
+
+	hw_dbg("Masking off all interrupts\n");
+	wr32(IGC_IMC, 0xffffffff);
+
+	wr32(IGC_RCTL, 0);
+	wr32(IGC_TCTL, IGC_TCTL_PSP);
+	wrfl();
+
+	usleep_range(10000, 20000);
+
+	ctrl = rd32(IGC_CTRL);
+
+	hw_dbg("Issuing a global reset to MAC\n");
+	wr32(IGC_CTRL, ctrl | IGC_CTRL_RST);
+
+	ret_val = igc_get_auto_rd_done(hw);
+	if (ret_val) {
+		/* When auto config read does not complete, do not
+		 * return with an error. This can happen in situations
+		 * where there is no eeprom and prevents getting link.
+		 */
+		hw_dbg("Auto Read Done did not complete\n");
+	}
+
+	/* Clear any pending interrupt events. */
+	wr32(IGC_IMC, 0xffffffff);
+	rd32(IGC_ICR);
+
+	return ret_val;
+}
+
+/**
+ * igc_init_nvm_params_base - Init NVM func ptrs.
+ * @hw: pointer to the HW structure
+ */
+static s32 igc_init_nvm_params_base(struct igc_hw *hw)
+{
+	struct igc_nvm_info *nvm = &hw->nvm;
+	u32 eecd = rd32(IGC_EECD);
+	u16 size;
+
+	size = (u16)((eecd & IGC_EECD_SIZE_EX_MASK) >>
+		     IGC_EECD_SIZE_EX_SHIFT);
+
+	/* Added to a constant, "size" becomes the left-shift value
+	 * for setting word_size.
+	 */
+	size += NVM_WORD_SIZE_BASE_SHIFT;
+
+	/* Just in case size is out of range, cap it to the largest
+	 * EEPROM size supported
+	 */
+	if (size > 15)
+		size = 15;
+
+	nvm->type = igc_nvm_eeprom_spi;
+	nvm->word_size = BIT(size);
+	nvm->opcode_bits = 8;
+	nvm->delay_usec = 1;
+
+	nvm->page_size = eecd & IGC_EECD_ADDR_BITS ? 32 : 8;
+	nvm->address_bits = eecd & IGC_EECD_ADDR_BITS ?
+			    16 : 8;
+
+	if (nvm->word_size == BIT(15))
+		nvm->page_size = 128;
+
+	return 0;
+}
+
+/**
+ * igc_setup_copper_link_base - Configure copper link settings
+ * @hw: pointer to the HW structure
+ *
+ * Configures the link for auto-neg or forced speed and duplex.  Then we check
+ * for link, once link is established calls to configure collision distance
+ * and flow control are called.
+ */
+static s32 igc_setup_copper_link_base(struct igc_hw *hw)
+{
+	s32  ret_val = 0;
+	u32 ctrl;
+
+	ctrl = rd32(IGC_CTRL);
+	ctrl |= IGC_CTRL_SLU;
+	ctrl &= ~(IGC_CTRL_FRCSPD | IGC_CTRL_FRCDPX);
+	wr32(IGC_CTRL, ctrl);
+
+	ret_val = igc_setup_copper_link(hw);
+
+	return ret_val;
+}
+
+/**
+ * igc_init_mac_params_base - Init MAC func ptrs.
+ * @hw: pointer to the HW structure
+ */
+static s32 igc_init_mac_params_base(struct igc_hw *hw)
+{
+	struct igc_dev_spec_base *dev_spec = &hw->dev_spec._base;
+	struct igc_mac_info *mac = &hw->mac;
+
+	/* Set mta register count */
+	mac->mta_reg_count = 128;
+	mac->rar_entry_count = IGC_RAR_ENTRIES;
+
+	/* reset */
+	mac->ops.reset_hw = igc_reset_hw_base;
+
+	mac->ops.acquire_swfw_sync = igc_acquire_swfw_sync_i225;
+	mac->ops.release_swfw_sync = igc_release_swfw_sync_i225;
+
+	/* Allow a single clear of the SW semaphore on I225 */
+	if (mac->type == igc_i225)
+		dev_spec->clear_semaphore_once = true;
+
+	/* physical interface link setup */
+	mac->ops.setup_physical_interface = igc_setup_copper_link_base;
+
+	return 0;
+}
+
+/**
+ * igc_init_phy_params_base - Init PHY func ptrs.
+ * @hw: pointer to the HW structure
+ */
+static s32 igc_init_phy_params_base(struct igc_hw *hw)
+{
+	struct igc_phy_info *phy = &hw->phy;
+	s32 ret_val = 0;
+
+	phy->autoneg_mask	= AUTONEG_ADVERTISE_SPEED_DEFAULT_2500;
+	phy->reset_delay_us	= 100;
+
+	/* set lan id */
+	hw->bus.func = (rd32(IGC_STATUS) & IGC_STATUS_FUNC_MASK) >>
+			IGC_STATUS_FUNC_SHIFT;
+
+	/* Make sure the PHY is in a good state. Several people have reported
+	 * firmware leaving the PHY's page select register set to something
+	 * other than the default of zero, which causes the PHY ID read to
+	 * access something other than the intended register.
+	 */
+	ret_val = hw->phy.ops.reset(hw);
+	if (ret_val) {
+		hw_dbg("Error resetting the PHY\n");
+		goto out;
+	}
+
+	ret_val = igc_get_phy_id(hw);
+	if (ret_val)
+		return ret_val;
+
+	igc_check_for_copper_link(hw);
+
+out:
+	return ret_val;
+}
+
+static s32 igc_get_invariants_base(struct igc_hw *hw)
+{
+	struct igc_mac_info *mac = &hw->mac;
+	s32 ret_val = 0;
+
+	switch (hw->device_id) {
+	case IGC_DEV_ID_I225_LM:
+	case IGC_DEV_ID_I225_V:
+	case IGC_DEV_ID_I225_I:
+	case IGC_DEV_ID_I220_V:
+	case IGC_DEV_ID_I225_K:
+	case IGC_DEV_ID_I225_K2:
+	case IGC_DEV_ID_I226_K:
+	case IGC_DEV_ID_I225_LMVP:
+	case IGC_DEV_ID_I226_LMVP:
+	case IGC_DEV_ID_I225_IT:
+	case IGC_DEV_ID_I226_LM:
+	case IGC_DEV_ID_I226_V:
+	case IGC_DEV_ID_I226_IT:
+	case IGC_DEV_ID_I221_V:
+	case IGC_DEV_ID_I226_BLANK_NVM:
+	case IGC_DEV_ID_I225_BLANK_NVM:
+		mac->type = igc_i225;
+		break;
+	default:
+		return -IGC_ERR_MAC_INIT;
+	}
+
+	hw->phy.media_type = igc_media_type_copper;
+
+	/* mac initialization and operations */
+	ret_val = igc_init_mac_params_base(hw);
+	if (ret_val)
+		goto out;
+
+	/* NVM initialization */
+	ret_val = igc_init_nvm_params_base(hw);
+	switch (hw->mac.type) {
+	case igc_i225:
+		ret_val = igc_init_nvm_params_i225(hw);
+		break;
+	default:
+		break;
+	}
+
+	/* setup PHY parameters */
+	ret_val = igc_init_phy_params_base(hw);
+	if (ret_val)
+		goto out;
+
+out:
+	return ret_val;
+}
+
+/**
+ * igc_acquire_phy_base - Acquire rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * Acquire access rights to the correct PHY.  This is a
+ * function pointer entry point called by the api module.
+ */
+static s32 igc_acquire_phy_base(struct igc_hw *hw)
+{
+	u16 mask = IGC_SWFW_PHY0_SM;
+
+	return hw->mac.ops.acquire_swfw_sync(hw, mask);
+}
+
+/**
+ * igc_release_phy_base - Release rights to access PHY
+ * @hw: pointer to the HW structure
+ *
+ * A wrapper to release access rights to the correct PHY.  This is a
+ * function pointer entry point called by the api module.
+ */
+static void igc_release_phy_base(struct igc_hw *hw)
+{
+	u16 mask = IGC_SWFW_PHY0_SM;
+
+	hw->mac.ops.release_swfw_sync(hw, mask);
+}
+
+/**
+ * igc_init_hw_base - Initialize hardware
+ * @hw: pointer to the HW structure
+ *
+ * This inits the hardware readying it for operation.
+ */
+static s32 igc_init_hw_base(struct igc_hw *hw)
+{
+	struct igc_mac_info *mac = &hw->mac;
+	u16 i, rar_count = mac->rar_entry_count;
+	s32 ret_val = 0;
+
+	/* Setup the receive address */
+	igc_init_rx_addrs(hw, rar_count);
+
+	/* Zero out the Multicast HASH table */
+	hw_dbg("Zeroing the MTA\n");
+	for (i = 0; i < mac->mta_reg_count; i++)
+		array_wr32(IGC_MTA, i, 0);
+
+	/* Zero out the Unicast HASH table */
+	hw_dbg("Zeroing the UTA\n");
+	for (i = 0; i < mac->uta_reg_count; i++)
+		array_wr32(IGC_UTA, i, 0);
+
+	/* Setup link and flow control */
+	ret_val = igc_setup_link(hw);
+
+	/* Clear all of the statistics registers (clear on read).  It is
+	 * important that we do this after we have tried to establish link
+	 * because the symbol error count will increment wildly if there
+	 * is no link.
+	 */
+	igc_clear_hw_cntrs_base(hw);
+
+	return ret_val;
+}
+
+/**
+ * igc_power_down_phy_copper_base - Remove link during PHY power down
+ * @hw: pointer to the HW structure
+ *
+ * In the case of a PHY power down to save power, or to turn off link during a
+ * driver unload, or wake on lan is not enabled, remove the link.
+ */
+void igc_power_down_phy_copper_base(struct igc_hw *hw)
+{
+	/* If the management interface is not enabled, then power down */
+	if (!(igc_enable_mng_pass_thru(hw) || igc_check_reset_block(hw)))
+		igc_power_down_phy_copper(hw);
+}
+
+/**
+ * igc_rx_fifo_flush_base - Clean rx fifo after Rx enable
+ * @hw: pointer to the HW structure
+ *
+ * After Rx enable, if manageability is enabled then there is likely some
+ * bad data at the start of the fifo and possibly in the DMA fifo.  This
+ * function clears the fifos and flushes any packets that came in as rx was
+ * being enabled.
+ */
+void igc_rx_fifo_flush_base(struct igc_hw *hw)
+{
+	u32 rctl, rlpml, rxdctl[4], rfctl, temp_rctl, rx_enabled;
+	int i, ms_wait;
+
+	/* disable IPv6 options as per hardware errata */
+	rfctl = rd32(IGC_RFCTL);
+	rfctl |= IGC_RFCTL_IPV6_EX_DIS;
+	wr32(IGC_RFCTL, rfctl);
+
+	if (!(rd32(IGC_MANC) & IGC_MANC_RCV_TCO_EN))
+		return;
+
+	/* Disable all Rx queues */
+	for (i = 0; i < 4; i++) {
+		rxdctl[i] = rd32(IGC_RXDCTL(i));
+		wr32(IGC_RXDCTL(i),
+		     rxdctl[i] & ~IGC_RXDCTL_QUEUE_ENABLE);
+	}
+	/* Poll all queues to verify they have shut down */
+	for (ms_wait = 0; ms_wait < 10; ms_wait++) {
+		usleep_range(1000, 2000);
+		rx_enabled = 0;
+		for (i = 0; i < 4; i++)
+			rx_enabled |= rd32(IGC_RXDCTL(i));
+		if (!(rx_enabled & IGC_RXDCTL_QUEUE_ENABLE))
+			break;
+	}
+
+	if (ms_wait == 10)
+		hw_dbg("Queue disable timed out after 10ms\n");
+
+	/* Clear RLPML, RCTL.SBP, RFCTL.LEF, and set RCTL.LPE so that all
+	 * incoming packets are rejected.  Set enable and wait 2ms so that
+	 * any packet that was coming in as RCTL.EN was set is flushed
+	 */
+	wr32(IGC_RFCTL, rfctl & ~IGC_RFCTL_LEF);
+
+	rlpml = rd32(IGC_RLPML);
+	wr32(IGC_RLPML, 0);
+
+	rctl = rd32(IGC_RCTL);
+	temp_rctl = rctl & ~(IGC_RCTL_EN | IGC_RCTL_SBP);
+	temp_rctl |= IGC_RCTL_LPE;
+
+	wr32(IGC_RCTL, temp_rctl);
+	wr32(IGC_RCTL, temp_rctl | IGC_RCTL_EN);
+	wrfl();
+	usleep_range(2000, 3000);
+
+	/* Enable Rx queues that were previously enabled and restore our
+	 * previous state
+	 */
+	for (i = 0; i < 4; i++)
+		wr32(IGC_RXDCTL(i), rxdctl[i]);
+	wr32(IGC_RCTL, rctl);
+	wrfl();
+
+	wr32(IGC_RLPML, rlpml);
+	wr32(IGC_RFCTL, rfctl);
+
+	/* Flush receive errors generated by workaround */
+	rd32(IGC_ROC);
+	rd32(IGC_RNBC);
+	rd32(IGC_MPC);
+}
+
+bool igc_is_device_id_i225(struct igc_hw *hw)
+{
+	switch (hw->device_id) {
+	case IGC_DEV_ID_I225_LM:
+	case IGC_DEV_ID_I225_V:
+	case IGC_DEV_ID_I225_I:
+	case IGC_DEV_ID_I225_K:
+	case IGC_DEV_ID_I225_K2:
+	case IGC_DEV_ID_I225_LMVP:
+	case IGC_DEV_ID_I225_IT:
+		return true;
+	default:
+		return false;
+	}
+}
+
+bool igc_is_device_id_i226(struct igc_hw *hw)
+{
+	switch (hw->device_id) {
+	case IGC_DEV_ID_I226_LM:
+	case IGC_DEV_ID_I226_V:
+	case IGC_DEV_ID_I226_K:
+	case IGC_DEV_ID_I226_IT:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static struct igc_mac_operations igc_mac_ops_base = {
+	.init_hw		= igc_init_hw_base,
+	.check_for_link		= igc_check_for_copper_link,
+	.rar_set		= igc_rar_set,
+	.read_mac_addr		= igc_read_mac_addr,
+	.get_speed_and_duplex	= igc_get_speed_and_duplex_copper,
+};
+
+static const struct igc_phy_operations igc_phy_ops_base = {
+	.acquire		= igc_acquire_phy_base,
+	.release		= igc_release_phy_base,
+	.reset			= igc_phy_hw_reset,
+	.read_reg		= igc_read_phy_reg_gpy,
+	.write_reg		= igc_write_phy_reg_gpy,
+};
+
+const struct igc_info igc_base_info = {
+	.get_invariants		= igc_get_invariants_base,
+	.mac_ops		= &igc_mac_ops_base,
+	.phy_ops		= &igc_phy_ops_base,
+};