diff options
Diffstat (limited to 'drivers/net/ethernet/intel/igc/igc_phy.c')
| -rw-r--r-- | drivers/net/ethernet/intel/igc/igc_phy.c | 795 |
1 files changed, 795 insertions, 0 deletions
diff --git a/drivers/net/ethernet/intel/igc/igc_phy.c b/drivers/net/ethernet/intel/igc/igc_phy.c new file mode 100644 index 000000000..53b77c969 --- /dev/null +++ b/drivers/net/ethernet/intel/igc/igc_phy.c @@ -0,0 +1,795 @@ +// SPDX-License-Identifier: GPL-2.0 +/* Copyright (c) 2018 Intel Corporation */ + +#include "igc_phy.h" + +/** + * igc_check_reset_block - Check if PHY reset is blocked + * @hw: pointer to the HW structure + * + * Read the PHY management control register and check whether a PHY reset + * is blocked. If a reset is not blocked return 0, otherwise + * return IGC_ERR_BLK_PHY_RESET (12). + */ +s32 igc_check_reset_block(struct igc_hw *hw) +{ + u32 manc; + + manc = rd32(IGC_MANC); + + return (manc & IGC_MANC_BLK_PHY_RST_ON_IDE) ? + IGC_ERR_BLK_PHY_RESET : 0; +} + +/** + * igc_get_phy_id - Retrieve the PHY ID and revision + * @hw: pointer to the HW structure + * + * Reads the PHY registers and stores the PHY ID and possibly the PHY + * revision in the hardware structure. + */ +s32 igc_get_phy_id(struct igc_hw *hw) +{ + struct igc_phy_info *phy = &hw->phy; + s32 ret_val = 0; + u16 phy_id; + + ret_val = phy->ops.read_reg(hw, PHY_ID1, &phy_id); + if (ret_val) + goto out; + + phy->id = (u32)(phy_id << 16); + usleep_range(200, 500); + ret_val = phy->ops.read_reg(hw, PHY_ID2, &phy_id); + if (ret_val) + goto out; + + phy->id |= (u32)(phy_id & PHY_REVISION_MASK); + phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK); + +out: + return ret_val; +} + +/** + * igc_phy_has_link - Polls PHY for link + * @hw: pointer to the HW structure + * @iterations: number of times to poll for link + * @usec_interval: delay between polling attempts + * @success: pointer to whether polling was successful or not + * + * Polls the PHY status register for link, 'iterations' number of times. + */ +s32 igc_phy_has_link(struct igc_hw *hw, u32 iterations, + u32 usec_interval, bool *success) +{ + u16 i, phy_status; + s32 ret_val = 0; + + for (i = 0; i < iterations; i++) { + /* Some PHYs require the PHY_STATUS register to be read + * twice due to the link bit being sticky. No harm doing + * it across the board. + */ + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val && usec_interval > 0) { + /* If the first read fails, another entity may have + * ownership of the resources, wait and try again to + * see if they have relinquished the resources yet. + */ + if (usec_interval >= 1000) + mdelay(usec_interval / 1000); + else + udelay(usec_interval); + } + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val) + break; + if (phy_status & MII_SR_LINK_STATUS) + break; + if (usec_interval >= 1000) + mdelay(usec_interval / 1000); + else + udelay(usec_interval); + } + + *success = (i < iterations) ? true : false; + + return ret_val; +} + +/** + * igc_power_up_phy_copper - Restore copper link in case of PHY power down + * @hw: pointer to the HW structure + * + * In the case of a PHY power down to save power, or to turn off link during a + * driver unload, restore the link to previous settings. + */ +void igc_power_up_phy_copper(struct igc_hw *hw) +{ + u16 mii_reg = 0; + + /* The PHY will retain its settings across a power down/up cycle */ + hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg); + mii_reg &= ~MII_CR_POWER_DOWN; + hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg); +} + +/** + * igc_power_down_phy_copper - Power down copper PHY + * @hw: pointer to the HW structure + * + * Power down PHY to save power when interface is down and wake on lan + * is not enabled. + */ +void igc_power_down_phy_copper(struct igc_hw *hw) +{ + u16 mii_reg = 0; + + /* The PHY will retain its settings across a power down/up cycle */ + hw->phy.ops.read_reg(hw, PHY_CONTROL, &mii_reg); + mii_reg |= MII_CR_POWER_DOWN; + + /* Temporary workaround - should be removed when PHY will implement + * IEEE registers as properly + */ + /* hw->phy.ops.write_reg(hw, PHY_CONTROL, mii_reg);*/ + usleep_range(1000, 2000); +} + +/** + * igc_check_downshift - Checks whether a downshift in speed occurred + * @hw: pointer to the HW structure + * + * A downshift is detected by querying the PHY link health. + */ +void igc_check_downshift(struct igc_hw *hw) +{ + struct igc_phy_info *phy = &hw->phy; + + /* speed downshift not supported */ + phy->speed_downgraded = false; +} + +/** + * igc_phy_hw_reset - PHY hardware reset + * @hw: pointer to the HW structure + * + * Verify the reset block is not blocking us from resetting. Acquire + * semaphore (if necessary) and read/set/write the device control reset + * bit in the PHY. Wait the appropriate delay time for the device to + * reset and release the semaphore (if necessary). + */ +s32 igc_phy_hw_reset(struct igc_hw *hw) +{ + struct igc_phy_info *phy = &hw->phy; + u32 phpm = 0, timeout = 10000; + s32 ret_val; + u32 ctrl; + + ret_val = igc_check_reset_block(hw); + if (ret_val) { + ret_val = 0; + goto out; + } + + ret_val = phy->ops.acquire(hw); + if (ret_val) + goto out; + + phpm = rd32(IGC_I225_PHPM); + + ctrl = rd32(IGC_CTRL); + wr32(IGC_CTRL, ctrl | IGC_CTRL_PHY_RST); + wrfl(); + + udelay(phy->reset_delay_us); + + wr32(IGC_CTRL, ctrl); + wrfl(); + + /* SW should guarantee 100us for the completion of the PHY reset */ + usleep_range(100, 150); + do { + phpm = rd32(IGC_I225_PHPM); + timeout--; + udelay(1); + } while (!(phpm & IGC_PHY_RST_COMP) && timeout); + + if (!timeout) + hw_dbg("Timeout is expired after a phy reset\n"); + + usleep_range(100, 150); + + phy->ops.release(hw); + +out: + return ret_val; +} + +/** + * igc_phy_setup_autoneg - Configure PHY for auto-negotiation + * @hw: pointer to the HW structure + * + * Reads the MII auto-neg advertisement register and/or the 1000T control + * register and if the PHY is already setup for auto-negotiation, then + * return successful. Otherwise, setup advertisement and flow control to + * the appropriate values for the wanted auto-negotiation. + */ +static s32 igc_phy_setup_autoneg(struct igc_hw *hw) +{ + struct igc_phy_info *phy = &hw->phy; + u16 aneg_multigbt_an_ctrl = 0; + u16 mii_1000t_ctrl_reg = 0; + u16 mii_autoneg_adv_reg; + s32 ret_val; + + phy->autoneg_advertised &= phy->autoneg_mask; + + /* Read the MII Auto-Neg Advertisement Register (Address 4). */ + ret_val = phy->ops.read_reg(hw, PHY_AUTONEG_ADV, &mii_autoneg_adv_reg); + if (ret_val) + return ret_val; + + if (phy->autoneg_mask & ADVERTISE_1000_FULL) { + /* Read the MII 1000Base-T Control Register (Address 9). */ + ret_val = phy->ops.read_reg(hw, PHY_1000T_CTRL, + &mii_1000t_ctrl_reg); + if (ret_val) + return ret_val; + } + + if (phy->autoneg_mask & ADVERTISE_2500_FULL) { + /* Read the MULTI GBT AN Control Register - reg 7.32 */ + ret_val = phy->ops.read_reg(hw, (STANDARD_AN_REG_MASK << + MMD_DEVADDR_SHIFT) | + ANEG_MULTIGBT_AN_CTRL, + &aneg_multigbt_an_ctrl); + + if (ret_val) + return ret_val; + } + + /* Need to parse both autoneg_advertised and fc and set up + * the appropriate PHY registers. First we will parse for + * autoneg_advertised software override. Since we can advertise + * a plethora of combinations, we need to check each bit + * individually. + */ + + /* First we clear all the 10/100 mb speed bits in the Auto-Neg + * Advertisement Register (Address 4) and the 1000 mb speed bits in + * the 1000Base-T Control Register (Address 9). + */ + mii_autoneg_adv_reg &= ~(NWAY_AR_100TX_FD_CAPS | + NWAY_AR_100TX_HD_CAPS | + NWAY_AR_10T_FD_CAPS | + NWAY_AR_10T_HD_CAPS); + mii_1000t_ctrl_reg &= ~(CR_1000T_HD_CAPS | CR_1000T_FD_CAPS); + + hw_dbg("autoneg_advertised %x\n", phy->autoneg_advertised); + + /* Do we want to advertise 10 Mb Half Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_10_HALF) { + hw_dbg("Advertise 10mb Half duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_10T_HD_CAPS; + } + + /* Do we want to advertise 10 Mb Full Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_10_FULL) { + hw_dbg("Advertise 10mb Full duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_10T_FD_CAPS; + } + + /* Do we want to advertise 100 Mb Half Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_100_HALF) { + hw_dbg("Advertise 100mb Half duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_100TX_HD_CAPS; + } + + /* Do we want to advertise 100 Mb Full Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_100_FULL) { + hw_dbg("Advertise 100mb Full duplex\n"); + mii_autoneg_adv_reg |= NWAY_AR_100TX_FD_CAPS; + } + + /* We do not allow the Phy to advertise 1000 Mb Half Duplex */ + if (phy->autoneg_advertised & ADVERTISE_1000_HALF) + hw_dbg("Advertise 1000mb Half duplex request denied!\n"); + + /* Do we want to advertise 1000 Mb Full Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_1000_FULL) { + hw_dbg("Advertise 1000mb Full duplex\n"); + mii_1000t_ctrl_reg |= CR_1000T_FD_CAPS; + } + + /* We do not allow the Phy to advertise 2500 Mb Half Duplex */ + if (phy->autoneg_advertised & ADVERTISE_2500_HALF) + hw_dbg("Advertise 2500mb Half duplex request denied!\n"); + + /* Do we want to advertise 2500 Mb Full Duplex? */ + if (phy->autoneg_advertised & ADVERTISE_2500_FULL) { + hw_dbg("Advertise 2500mb Full duplex\n"); + aneg_multigbt_an_ctrl |= CR_2500T_FD_CAPS; + } else { + aneg_multigbt_an_ctrl &= ~CR_2500T_FD_CAPS; + } + + /* Check for a software override of the flow control settings, and + * setup the PHY advertisement registers accordingly. If + * auto-negotiation is enabled, then software will have to set the + * "PAUSE" bits to the correct value in the Auto-Negotiation + * Advertisement Register (PHY_AUTONEG_ADV) and re-start auto- + * negotiation. + * + * The possible values of the "fc" parameter are: + * 0: Flow control is completely disabled + * 1: Rx flow control is enabled (we can receive pause frames + * but not send pause frames). + * 2: Tx flow control is enabled (we can send pause frames + * but we do not support receiving pause frames). + * 3: Both Rx and Tx flow control (symmetric) are enabled. + * other: No software override. The flow control configuration + * in the EEPROM is used. + */ + switch (hw->fc.current_mode) { + case igc_fc_none: + /* Flow control (Rx & Tx) is completely disabled by a + * software over-ride. + */ + mii_autoneg_adv_reg &= ~(NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + case igc_fc_rx_pause: + /* Rx Flow control is enabled, and Tx Flow control is + * disabled, by a software over-ride. + * + * Since there really isn't a way to advertise that we are + * capable of Rx Pause ONLY, we will advertise that we + * support both symmetric and asymmetric Rx PAUSE. Later + * (in igc_config_fc_after_link_up) we will disable the + * hw's ability to send PAUSE frames. + */ + mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + case igc_fc_tx_pause: + /* Tx Flow control is enabled, and Rx Flow control is + * disabled, by a software over-ride. + */ + mii_autoneg_adv_reg |= NWAY_AR_ASM_DIR; + mii_autoneg_adv_reg &= ~NWAY_AR_PAUSE; + break; + case igc_fc_full: + /* Flow control (both Rx and Tx) is enabled by a software + * over-ride. + */ + mii_autoneg_adv_reg |= (NWAY_AR_ASM_DIR | NWAY_AR_PAUSE); + break; + default: + hw_dbg("Flow control param set incorrectly\n"); + return -IGC_ERR_CONFIG; + } + + ret_val = phy->ops.write_reg(hw, PHY_AUTONEG_ADV, mii_autoneg_adv_reg); + if (ret_val) + return ret_val; + + hw_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg); + + if (phy->autoneg_mask & ADVERTISE_1000_FULL) + ret_val = phy->ops.write_reg(hw, PHY_1000T_CTRL, + mii_1000t_ctrl_reg); + + if (phy->autoneg_mask & ADVERTISE_2500_FULL) + ret_val = phy->ops.write_reg(hw, + (STANDARD_AN_REG_MASK << + MMD_DEVADDR_SHIFT) | + ANEG_MULTIGBT_AN_CTRL, + aneg_multigbt_an_ctrl); + + return ret_val; +} + +/** + * igc_wait_autoneg - Wait for auto-neg completion + * @hw: pointer to the HW structure + * + * Waits for auto-negotiation to complete or for the auto-negotiation time + * limit to expire, which ever happens first. + */ +static s32 igc_wait_autoneg(struct igc_hw *hw) +{ + u16 i, phy_status; + s32 ret_val = 0; + + /* Break after autoneg completes or PHY_AUTO_NEG_LIMIT expires. */ + for (i = PHY_AUTO_NEG_LIMIT; i > 0; i--) { + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val) + break; + ret_val = hw->phy.ops.read_reg(hw, PHY_STATUS, &phy_status); + if (ret_val) + break; + if (phy_status & MII_SR_AUTONEG_COMPLETE) + break; + msleep(100); + } + + /* PHY_AUTO_NEG_TIME expiration doesn't guarantee auto-negotiation + * has completed. + */ + return ret_val; +} + +/** + * igc_copper_link_autoneg - Setup/Enable autoneg for copper link + * @hw: pointer to the HW structure + * + * Performs initial bounds checking on autoneg advertisement parameter, then + * configure to advertise the full capability. Setup the PHY to autoneg + * and restart the negotiation process between the link partner. If + * autoneg_wait_to_complete, then wait for autoneg to complete before exiting. + */ +static s32 igc_copper_link_autoneg(struct igc_hw *hw) +{ + struct igc_phy_info *phy = &hw->phy; + u16 phy_ctrl; + s32 ret_val; + + /* Perform some bounds checking on the autoneg advertisement + * parameter. + */ + phy->autoneg_advertised &= phy->autoneg_mask; + + /* If autoneg_advertised is zero, we assume it was not defaulted + * by the calling code so we set to advertise full capability. + */ + if (phy->autoneg_advertised == 0) + phy->autoneg_advertised = phy->autoneg_mask; + + hw_dbg("Reconfiguring auto-neg advertisement params\n"); + ret_val = igc_phy_setup_autoneg(hw); + if (ret_val) { + hw_dbg("Error Setting up Auto-Negotiation\n"); + goto out; + } + hw_dbg("Restarting Auto-Neg\n"); + + /* Restart auto-negotiation by setting the Auto Neg Enable bit and + * the Auto Neg Restart bit in the PHY control register. + */ + ret_val = phy->ops.read_reg(hw, PHY_CONTROL, &phy_ctrl); + if (ret_val) + goto out; + + phy_ctrl |= (MII_CR_AUTO_NEG_EN | MII_CR_RESTART_AUTO_NEG); + ret_val = phy->ops.write_reg(hw, PHY_CONTROL, phy_ctrl); + if (ret_val) + goto out; + + /* Does the user want to wait for Auto-Neg to complete here, or + * check at a later time (for example, callback routine). + */ + if (phy->autoneg_wait_to_complete) { + ret_val = igc_wait_autoneg(hw); + if (ret_val) { + hw_dbg("Error while waiting for autoneg to complete\n"); + goto out; + } + } + + hw->mac.get_link_status = true; + +out: + return ret_val; +} + +/** + * igc_setup_copper_link - Configure copper link settings + * @hw: pointer to the HW structure + * + * Calls the appropriate function to configure the link for auto-neg or forced + * speed and duplex. Then we check for link, once link is established calls + * to configure collision distance and flow control are called. If link is + * not established, we return -IGC_ERR_PHY (-2). + */ +s32 igc_setup_copper_link(struct igc_hw *hw) +{ + s32 ret_val = 0; + bool link; + + if (hw->mac.autoneg) { + /* Setup autoneg and flow control advertisement and perform + * autonegotiation. + */ + ret_val = igc_copper_link_autoneg(hw); + if (ret_val) + goto out; + } else { + /* PHY will be set to 10H, 10F, 100H or 100F + * depending on user settings. + */ + hw_dbg("Forcing Speed and Duplex\n"); + ret_val = hw->phy.ops.force_speed_duplex(hw); + if (ret_val) { + hw_dbg("Error Forcing Speed and Duplex\n"); + goto out; + } + } + + /* Check link status. Wait up to 100 microseconds for link to become + * valid. + */ + ret_val = igc_phy_has_link(hw, COPPER_LINK_UP_LIMIT, 10, &link); + if (ret_val) + goto out; + + if (link) { + hw_dbg("Valid link established!!!\n"); + igc_config_collision_dist(hw); + ret_val = igc_config_fc_after_link_up(hw); + } else { + hw_dbg("Unable to establish link!!!\n"); + } + +out: + return ret_val; +} + +/** + * igc_read_phy_reg_mdic - Read MDI control register + * @hw: pointer to the HW structure + * @offset: register offset to be read + * @data: pointer to the read data + * + * Reads the MDI control register in the PHY at offset and stores the + * information read to data. + */ +static s32 igc_read_phy_reg_mdic(struct igc_hw *hw, u32 offset, u16 *data) +{ + struct igc_phy_info *phy = &hw->phy; + u32 i, mdic = 0; + s32 ret_val = 0; + + if (offset > MAX_PHY_REG_ADDRESS) { + hw_dbg("PHY Address %d is out of range\n", offset); + ret_val = -IGC_ERR_PARAM; + goto out; + } + + /* Set up Op-code, Phy Address, and register offset in the MDI + * Control register. The MAC will take care of interfacing with the + * PHY to retrieve the desired data. + */ + mdic = ((offset << IGC_MDIC_REG_SHIFT) | + (phy->addr << IGC_MDIC_PHY_SHIFT) | + (IGC_MDIC_OP_READ)); + + wr32(IGC_MDIC, mdic); + + /* Poll the ready bit to see if the MDI read completed + * Increasing the time out as testing showed failures with + * the lower time out + */ + for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) { + udelay(50); + mdic = rd32(IGC_MDIC); + if (mdic & IGC_MDIC_READY) + break; + } + if (!(mdic & IGC_MDIC_READY)) { + hw_dbg("MDI Read did not complete\n"); + ret_val = -IGC_ERR_PHY; + goto out; + } + if (mdic & IGC_MDIC_ERROR) { + hw_dbg("MDI Error\n"); + ret_val = -IGC_ERR_PHY; + goto out; + } + *data = (u16)mdic; + +out: + return ret_val; +} + +/** + * igc_write_phy_reg_mdic - Write MDI control register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write to register at offset + * + * Writes data to MDI control register in the PHY at offset. + */ +static s32 igc_write_phy_reg_mdic(struct igc_hw *hw, u32 offset, u16 data) +{ + struct igc_phy_info *phy = &hw->phy; + u32 i, mdic = 0; + s32 ret_val = 0; + + if (offset > MAX_PHY_REG_ADDRESS) { + hw_dbg("PHY Address %d is out of range\n", offset); + ret_val = -IGC_ERR_PARAM; + goto out; + } + + /* Set up Op-code, Phy Address, and register offset in the MDI + * Control register. The MAC will take care of interfacing with the + * PHY to write the desired data. + */ + mdic = (((u32)data) | + (offset << IGC_MDIC_REG_SHIFT) | + (phy->addr << IGC_MDIC_PHY_SHIFT) | + (IGC_MDIC_OP_WRITE)); + + wr32(IGC_MDIC, mdic); + + /* Poll the ready bit to see if the MDI read completed + * Increasing the time out as testing showed failures with + * the lower time out + */ + for (i = 0; i < IGC_GEN_POLL_TIMEOUT; i++) { + udelay(50); + mdic = rd32(IGC_MDIC); + if (mdic & IGC_MDIC_READY) + break; + } + if (!(mdic & IGC_MDIC_READY)) { + hw_dbg("MDI Write did not complete\n"); + ret_val = -IGC_ERR_PHY; + goto out; + } + if (mdic & IGC_MDIC_ERROR) { + hw_dbg("MDI Error\n"); + ret_val = -IGC_ERR_PHY; + goto out; + } + +out: + return ret_val; +} + +/** + * __igc_access_xmdio_reg - Read/write XMDIO register + * @hw: pointer to the HW structure + * @address: XMDIO address to program + * @dev_addr: device address to program + * @data: pointer to value to read/write from/to the XMDIO address + * @read: boolean flag to indicate read or write + */ +static s32 __igc_access_xmdio_reg(struct igc_hw *hw, u16 address, + u8 dev_addr, u16 *data, bool read) +{ + s32 ret_val; + + ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, dev_addr); + if (ret_val) + return ret_val; + + ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAAD, address); + if (ret_val) + return ret_val; + + ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, IGC_MMDAC_FUNC_DATA | + dev_addr); + if (ret_val) + return ret_val; + + if (read) + ret_val = hw->phy.ops.read_reg(hw, IGC_MMDAAD, data); + else + ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAAD, *data); + if (ret_val) + return ret_val; + + /* Recalibrate the device back to 0 */ + ret_val = hw->phy.ops.write_reg(hw, IGC_MMDAC, 0); + if (ret_val) + return ret_val; + + return ret_val; +} + +/** + * igc_read_xmdio_reg - Read XMDIO register + * @hw: pointer to the HW structure + * @addr: XMDIO address to program + * @dev_addr: device address to program + * @data: value to be read from the EMI address + */ +static s32 igc_read_xmdio_reg(struct igc_hw *hw, u16 addr, + u8 dev_addr, u16 *data) +{ + return __igc_access_xmdio_reg(hw, addr, dev_addr, data, true); +} + +/** + * igc_write_xmdio_reg - Write XMDIO register + * @hw: pointer to the HW structure + * @addr: XMDIO address to program + * @dev_addr: device address to program + * @data: value to be written to the XMDIO address + */ +static s32 igc_write_xmdio_reg(struct igc_hw *hw, u16 addr, + u8 dev_addr, u16 data) +{ + return __igc_access_xmdio_reg(hw, addr, dev_addr, &data, false); +} + +/** + * igc_write_phy_reg_gpy - Write GPY PHY register + * @hw: pointer to the HW structure + * @offset: register offset to write to + * @data: data to write at register offset + * + * Acquires semaphore, if necessary, then writes the data to PHY register + * at the offset. Release any acquired semaphores before exiting. + */ +s32 igc_write_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 data) +{ + u8 dev_addr = (offset & GPY_MMD_MASK) >> GPY_MMD_SHIFT; + s32 ret_val; + + offset = offset & GPY_REG_MASK; + + if (!dev_addr) { + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + ret_val = igc_write_phy_reg_mdic(hw, offset, data); + hw->phy.ops.release(hw); + } else { + ret_val = igc_write_xmdio_reg(hw, (u16)offset, dev_addr, + data); + } + + return ret_val; +} + +/** + * igc_read_phy_reg_gpy - Read GPY PHY register + * @hw: pointer to the HW structure + * @offset: lower half is register offset to read to + * upper half is MMD to use. + * @data: data to read at register offset + * + * Acquires semaphore, if necessary, then reads the data in the PHY register + * at the offset. Release any acquired semaphores before exiting. + */ +s32 igc_read_phy_reg_gpy(struct igc_hw *hw, u32 offset, u16 *data) +{ + u8 dev_addr = (offset & GPY_MMD_MASK) >> GPY_MMD_SHIFT; + s32 ret_val; + + offset = offset & GPY_REG_MASK; + + if (!dev_addr) { + ret_val = hw->phy.ops.acquire(hw); + if (ret_val) + return ret_val; + ret_val = igc_read_phy_reg_mdic(hw, offset, data); + hw->phy.ops.release(hw); + } else { + ret_val = igc_read_xmdio_reg(hw, (u16)offset, dev_addr, + data); + } + + return ret_val; +} + +/** + * igc_read_phy_fw_version - Read gPHY firmware version + * @hw: pointer to the HW structure + */ +u16 igc_read_phy_fw_version(struct igc_hw *hw) +{ + struct igc_phy_info *phy = &hw->phy; + u16 gphy_version = 0; + u16 ret_val; + + /* NVM image version is reported as firmware version for i225 device */ + ret_val = phy->ops.read_reg(hw, IGC_GPHY_VERSION, &gphy_version); + if (ret_val) + hw_dbg("igc_phy: read wrong gphy version\n"); + + return gphy_version; +} |