diff options
Diffstat (limited to 'include/linux/mfd/max8998.h')
| -rw-r--r-- | include/linux/mfd/max8998.h | 106 |
1 files changed, 106 insertions, 0 deletions
diff --git a/include/linux/mfd/max8998.h b/include/linux/mfd/max8998.h new file mode 100644 index 000000000..79c020bd0 --- /dev/null +++ b/include/linux/mfd/max8998.h @@ -0,0 +1,106 @@ +/* SPDX-License-Identifier: GPL-2.0+ */ +/* + * max8998.h - Voltage regulator driver for the Maxim 8998 + * + * Copyright (C) 2009-2010 Samsung Electrnoics + * Kyungmin Park <kyungmin.park@samsung.com> + * Marek Szyprowski <m.szyprowski@samsung.com> + */ + +#ifndef __LINUX_MFD_MAX8998_H +#define __LINUX_MFD_MAX8998_H + +#include <linux/regulator/machine.h> + +/* MAX 8998 regulator ids */ +enum { + MAX8998_LDO2 = 2, + MAX8998_LDO3, + MAX8998_LDO4, + MAX8998_LDO5, + MAX8998_LDO6, + MAX8998_LDO7, + MAX8998_LDO8, + MAX8998_LDO9, + MAX8998_LDO10, + MAX8998_LDO11, + MAX8998_LDO12, + MAX8998_LDO13, + MAX8998_LDO14, + MAX8998_LDO15, + MAX8998_LDO16, + MAX8998_LDO17, + MAX8998_BUCK1, + MAX8998_BUCK2, + MAX8998_BUCK3, + MAX8998_BUCK4, + MAX8998_EN32KHZ_AP, + MAX8998_EN32KHZ_CP, + MAX8998_ENVICHG, + MAX8998_ESAFEOUT1, + MAX8998_ESAFEOUT2, + MAX8998_CHARGER, +}; + +/** + * max8998_regulator_data - regulator data + * @id: regulator id + * @initdata: regulator init data (contraints, supplies, ...) + * @reg_node: DT node of regulator (unused on non-DT platforms) + */ +struct max8998_regulator_data { + int id; + struct regulator_init_data *initdata; + struct device_node *reg_node; +}; + +/** + * struct max8998_board - packages regulator init data + * @regulators: array of defined regulators + * @num_regulators: number of regulators used + * @irq_base: base IRQ number for max8998, required for IRQs + * @ono: power onoff IRQ number for max8998 + * @buck_voltage_lock: Do NOT change the values of the following six + * registers set by buck?_voltage?. The voltage of BUCK1/2 cannot + * be other than the preset values. + * @buck1_voltage: BUCK1 DVS mode 1 voltage registers + * @buck2_voltage: BUCK2 DVS mode 2 voltage registers + * @buck1_set1: BUCK1 gpio pin 1 to set output voltage + * @buck1_set2: BUCK1 gpio pin 2 to set output voltage + * @buck1_default_idx: Default for BUCK1 gpio pin 1, 2 + * @buck2_set3: BUCK2 gpio pin to set output voltage + * @buck2_default_idx: Default for BUCK2 gpio pin. + * @wakeup: Allow to wake up from suspend + * @rtc_delay: LP3974 RTC chip bug that requires delay after a register + * write before reading it. + * @eoc: End of Charge Level in percent: 10% ~ 45% by 5% step + * If it equals 0, leave it unchanged. + * Otherwise, it is a invalid value. + * @restart: Restart Level in mV: 100, 150, 200, and -1 for disable. + * If it equals 0, leave it unchanged. + * Otherwise, it is a invalid value. + * @timeout: Full Timeout in hours: 5, 6, 7, and -1 for disable. + * If it equals 0, leave it unchanged. + * Otherwise, leave it unchanged. + */ +struct max8998_platform_data { + struct max8998_regulator_data *regulators; + int num_regulators; + unsigned int irq_base; + int ono; + bool buck_voltage_lock; + int buck1_voltage[4]; + int buck2_voltage[2]; + int buck1_set1; + int buck1_set2; + int buck1_default_idx; + int buck2_set3; + int buck2_default_idx; + bool wakeup; + bool rtc_delay; + int eoc; + int restart; + int timeout; +}; + +#endif /* __LINUX_MFD_MAX8998_H */ |