diff options
Diffstat (limited to 'include/linux/mfd/wm8994/pdata.h')
| -rw-r--r-- | include/linux/mfd/wm8994/pdata.h | 236 |
1 files changed, 236 insertions, 0 deletions
diff --git a/include/linux/mfd/wm8994/pdata.h b/include/linux/mfd/wm8994/pdata.h new file mode 100644 index 000000000..6e2962ef5 --- /dev/null +++ b/include/linux/mfd/wm8994/pdata.h @@ -0,0 +1,236 @@ +/* SPDX-License-Identifier: GPL-2.0-or-later */ +/* + * include/linux/mfd/wm8994/pdata.h -- Platform data for WM8994 + * + * Copyright 2009 Wolfson Microelectronics PLC. + * + * Author: Mark Brown <broonie@opensource.wolfsonmicro.com> + */ + +#ifndef __MFD_WM8994_PDATA_H__ +#define __MFD_WM8994_PDATA_H__ + +#define WM8994_NUM_LDO 2 +#define WM8994_NUM_GPIO 11 +#define WM8994_NUM_AIF 3 + +struct wm8994_ldo_pdata { + const struct regulator_init_data *init_data; +}; + +#define WM8994_CONFIGURE_GPIO 0x10000 + +#define WM8994_DRC_REGS 5 +#define WM8994_EQ_REGS 20 +#define WM8958_MBC_CUTOFF_REGS 20 +#define WM8958_MBC_COEFF_REGS 48 +#define WM8958_MBC_COMBINED_REGS 56 +#define WM8958_VSS_HPF_REGS 2 +#define WM8958_VSS_REGS 148 +#define WM8958_ENH_EQ_REGS 32 + +/** + * DRC configurations are specified with a label and a set of register + * values to write (the enable bits will be ignored). At runtime an + * enumerated control will be presented for each DRC block allowing + * the user to choose the configuration to use. + * + * Configurations may be generated by hand or by using the DRC control + * panel provided by the WISCE - see http://www.wolfsonmicro.com/wisce/ + * for details. + */ +struct wm8994_drc_cfg { + const char *name; + u16 regs[WM8994_DRC_REGS]; +}; + +/** + * ReTune Mobile configurations are specified with a label, sample + * rate and set of values to write (the enable bits will be ignored). + * + * Configurations are expected to be generated using the ReTune Mobile + * control panel in WISCE - see http://www.wolfsonmicro.com/wisce/ + */ +struct wm8994_retune_mobile_cfg { + const char *name; + unsigned int rate; + u16 regs[WM8994_EQ_REGS]; +}; + +/** + * Multiband compressor configurations are specified with a label and + * two sets of values to write. Configurations are expected to be + * generated using the multiband compressor configuration panel in + * WISCE - see http://www.wolfsonmicro.com/wisce/ + */ +struct wm8958_mbc_cfg { + const char *name; + u16 cutoff_regs[WM8958_MBC_CUTOFF_REGS]; + u16 coeff_regs[WM8958_MBC_COEFF_REGS]; + + /* Coefficient layout when using MBC+VSS firmware */ + u16 combined_regs[WM8958_MBC_COMBINED_REGS]; +}; + +/** + * VSS HPF configurations are specified with a label and two values to + * write. Configurations are expected to be generated using the + * multiband compressor configuration panel in WISCE - see + * http://www.wolfsonmicro.com/wisce/ + */ +struct wm8958_vss_hpf_cfg { + const char *name; + u16 regs[WM8958_VSS_HPF_REGS]; +}; + +/** + * VSS configurations are specified with a label and array of values + * to write. Configurations are expected to be generated using the + * multiband compressor configuration panel in WISCE - see + * http://www.wolfsonmicro.com/wisce/ + */ +struct wm8958_vss_cfg { + const char *name; + u16 regs[WM8958_VSS_REGS]; +}; + +/** + * Enhanced EQ configurations are specified with a label and array of + * values to write. Configurations are expected to be generated using + * the multiband compressor configuration panel in WISCE - see + * http://www.wolfsonmicro.com/wisce/ + */ +struct wm8958_enh_eq_cfg { + const char *name; + u16 regs[WM8958_ENH_EQ_REGS]; +}; + +/** + * Microphone detection rates, used to tune response rates and power + * consumption for WM8958/WM1811 microphone detection. + * + * @sysclk: System clock rate to use this configuration for. + * @idle: True if this configuration should use when no accessory is detected, + * false otherwise. + * @start: Value for MICD_BIAS_START_TIME register field (not shifted). + * @rate: Value for MICD_RATE register field (not shifted). + */ +struct wm8958_micd_rate { + int sysclk; + bool idle; + int start; + int rate; +}; + +struct wm8994_pdata { + int gpio_base; + + /** + * Default values for GPIOs if non-zero, WM8994_CONFIGURE_GPIO + * can be used for all zero values. + */ + int gpio_defaults[WM8994_NUM_GPIO]; + + struct wm8994_ldo_pdata ldo[WM8994_NUM_LDO]; + + int irq_base; /** Base IRQ number for WM8994, required for IRQs */ + unsigned long irq_flags; /** user irq flags */ + + int num_drc_cfgs; + struct wm8994_drc_cfg *drc_cfgs; + + int num_retune_mobile_cfgs; + struct wm8994_retune_mobile_cfg *retune_mobile_cfgs; + + int num_mbc_cfgs; + struct wm8958_mbc_cfg *mbc_cfgs; + + int num_vss_cfgs; + struct wm8958_vss_cfg *vss_cfgs; + + int num_vss_hpf_cfgs; + struct wm8958_vss_hpf_cfg *vss_hpf_cfgs; + + int num_enh_eq_cfgs; + struct wm8958_enh_eq_cfg *enh_eq_cfgs; + + int num_micd_rates; + struct wm8958_micd_rate *micd_rates; + + /* Power up delays to add after microphone bias power up (ms) */ + int micb1_delay; + int micb2_delay; + + /* LINEOUT can be differential or single ended */ + unsigned int lineout1_diff:1; + unsigned int lineout2_diff:1; + + /* Common mode feedback */ + unsigned int lineout1fb:1; + unsigned int lineout2fb:1; + + /* Delay between detecting a jack and starting microphone + * detect (specified in ms) + */ + int micdet_delay; + + /* Delay between microphone detect completing and reporting on + * insert (specified in ms) + */ + int mic_id_delay; + + /* IRQ for microphone detection if brought out directly as a + * signal. + */ + int micdet_irq; + + /* WM8994 microphone biases: 0=0.9*AVDD1 1=0.65*AVVD1 */ + unsigned int micbias1_lvl:1; + unsigned int micbias2_lvl:1; + + /* WM8994 jack detect threashold levels, see datasheet for values */ + unsigned int jd_scthr:2; + unsigned int jd_thr:2; + + /* Configure WM1811 jack detection for use with external capacitor */ + unsigned int jd_ext_cap:1; + + /* WM8958 microphone bias configuration */ + int micbias[2]; + + /* WM8958 microphone detection ranges */ + u16 micd_lvl_sel; + + /* Disable the internal pull downs on the LDOs if they are + * always driven (eg, connected to an always on supply or + * GPIO that always drives an output. If they float power + * consumption will rise. + */ + bool ldo_ena_always_driven; + + /* + * SPKMODE must be pulled internally by the device on this + * system. + */ + bool spkmode_pu; + + /* + * CS/ADDR must be pulled internally by the device on this + * system. + */ + bool csnaddr_pd; + + /** + * Maximum number of channels clocks will be generated for, + * useful for systems where and I2S bus with multiple data + * lines is mastered. + */ + int max_channels_clocked[WM8994_NUM_AIF]; + + /** + * GPIO for the IRQ pin if host only supports edge triggering + */ + int irq_gpio; +}; + +#endif |