1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
|
The Exynos display port interface should be configured based on
the type of panel connected to it.
We use two nodes:
-dp-controller node
-dptx-phy node(defined inside dp-controller node)
For the DP-PHY initialization, we use the dptx-phy node.
Required properties for dptx-phy: deprecated, use phys and phy-names
-reg: deprecated
Base address of DP PHY register.
-samsung,enable-mask: deprecated
The bit-mask used to enable/disable DP PHY.
For the Panel initialization, we read data from dp-controller node.
Required properties for dp-controller:
-compatible:
should be "samsung,exynos5-dp".
-reg:
physical base address of the controller and length
of memory mapped region.
-interrupts:
interrupt combiner values.
-clocks:
from common clock binding: handle to dp clock.
-clock-names:
from common clock binding: Shall be "dp".
-phys:
from general PHY binding: the phandle for the PHY device.
-phy-names:
from general PHY binding: Should be "dp".
Optional properties for dp-controller:
-interlaced:
interlace scan mode.
Progressive if defined, Interlaced if not defined
-vsync-active-high:
VSYNC polarity configuration.
High if defined, Low if not defined
-hsync-active-high:
HSYNC polarity configuration.
High if defined, Low if not defined
-samsung,hpd-gpio:
Hotplug detect GPIO.
Indicates which GPIO should be used for hotplug
detection
-video interfaces: Device node can contain video interface port
nodes according to [1].
- display-timings: timings for the connected panel as described by
Documentation/devicetree/bindings/display/panel/display-timing.txt
For the below properties, please refer to Analogix DP binding document:
* Documentation/devicetree/bindings/display/bridge/analogix_dp.txt
-phys (required)
-phy-names (required)
-hpd-gpios (optional)
force-hpd (optional)
Deprecated properties for DisplayPort:
-interlaced: deprecated prop that can parsed from drm_display_mode.
-vsync-active-high: deprecated prop that can parsed from drm_display_mode.
-hsync-active-high: deprecated prop that can parsed from drm_display_mode.
-samsung,ycbcr-coeff: deprecated prop that can parsed from drm_display_mode.
-samsung,dynamic-range: deprecated prop that can parsed from drm_display_mode.
-samsung,color-space: deprecated prop that can parsed from drm_display_info.
-samsung,color-depth: deprecated prop that can parsed from drm_display_info.
-samsung,link-rate: deprecated prop that can reading from monitor by dpcd method.
-samsung,lane-count: deprecated prop that can reading from monitor by dpcd method.
-samsung,hpd-gpio: deprecated name for hpd-gpios.
-------------------------------------------------------------------------------
Example:
SOC specific portion:
dp-controller {
compatible = "samsung,exynos5-dp";
reg = <0x145b0000 0x10000>;
interrupts = <10 3>;
interrupt-parent = <&combiner>;
clocks = <&clock 342>;
clock-names = "dp";
phys = <&dp_phy>;
phy-names = "dp";
};
Board Specific portion:
dp-controller {
display-timings {
native-mode = <&lcd_timing>;
lcd_timing: 1366x768 {
clock-frequency = <70589280>;
hactive = <1366>;
vactive = <768>;
hfront-porch = <40>;
hback-porch = <40>;
hsync-len = <32>;
vback-porch = <10>;
vfront-porch = <12>;
vsync-len = <6>;
};
};
ports {
port@0 {
dp_out: endpoint {
remote-endpoint = <&bridge_in>;
};
};
};
};
|
