1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/net/can/fsl,flexcan.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title:
Flexcan CAN controller on Freescale's ARM and PowerPC system-on-a-chip (SOC).
maintainers:
- Marc Kleine-Budde <mkl@pengutronix.de>
allOf:
- $ref: can-controller.yaml#
properties:
compatible:
oneOf:
- enum:
- fsl,imx8qm-flexcan
- fsl,imx8mp-flexcan
- fsl,imx6q-flexcan
- fsl,imx28-flexcan
- fsl,imx25-flexcan
- fsl,p1010-flexcan
- fsl,vf610-flexcan
- fsl,ls1021ar2-flexcan
- fsl,lx2160ar1-flexcan
- items:
- enum:
- fsl,imx53-flexcan
- fsl,imx35-flexcan
- const: fsl,imx25-flexcan
- items:
- enum:
- fsl,imx7d-flexcan
- fsl,imx6ul-flexcan
- fsl,imx6sx-flexcan
- const: fsl,imx6q-flexcan
- items:
- enum:
- fsl,ls1028ar1-flexcan
- const: fsl,lx2160ar1-flexcan
reg:
maxItems: 1
interrupts:
maxItems: 1
clocks:
maxItems: 2
clock-names:
items:
- const: ipg
- const: per
clock-frequency:
description: |
The oscillator frequency driving the flexcan device, filled in by the
boot loader. This property should only be used the used operating system
doesn't support the clocks and clock-names property.
xceiver-supply:
description: Regulator that powers the CAN transceiver.
big-endian:
$ref: /schemas/types.yaml#/definitions/flag
description: |
This means the registers of FlexCAN controller are big endian. This is
optional property.i.e. if this property is not present in device tree
node then controller is assumed to be little endian. If this property is
present then controller is assumed to be big endian.
fsl,stop-mode:
description: |
Register bits of stop mode control.
The format should be as follows:
<gpr req_gpr req_bit>
gpr is the phandle to general purpose register node.
req_gpr is the gpr register offset of CAN stop request.
req_bit is the bit offset of CAN stop request.
$ref: /schemas/types.yaml#/definitions/phandle-array
items:
- items:
- description: The 'gpr' is the phandle to general purpose register node.
- description: The 'req_gpr' is the gpr register offset of CAN stop request.
maximum: 0xff
- description: The 'req_bit' is the bit offset of CAN stop request.
maximum: 0x1f
fsl,clk-source:
description: |
Select the clock source to the CAN Protocol Engine (PE). It's SoC
implementation dependent. Refer to RM for detailed definition. If this
property is not set in device tree node then driver selects clock source 1
by default.
0: clock source 0 (oscillator clock)
1: clock source 1 (peripheral clock)
$ref: /schemas/types.yaml#/definitions/uint8
default: 1
minimum: 0
maximum: 1
wakeup-source:
$ref: /schemas/types.yaml#/definitions/flag
description:
Enable CAN remote wakeup.
fsl,scu-index:
description: |
The scu index of CAN instance.
For SoCs with SCU support, need setup stop mode via SCU firmware, so this
property can help indicate a resource. It supports up to 3 CAN instances
now.
$ref: /schemas/types.yaml#/definitions/uint8
minimum: 0
maximum: 2
termination-gpios: true
termination-ohms: true
required:
- compatible
- reg
- interrupts
additionalProperties: false
examples:
- |
can@1c000 {
compatible = "fsl,p1010-flexcan";
reg = <0x1c000 0x1000>;
interrupts = <48 0x2>;
interrupt-parent = <&mpic>;
clock-frequency = <200000000>;
fsl,clk-source = /bits/ 8 <0>;
};
- |
#include <dt-bindings/interrupt-controller/irq.h>
can@2090000 {
compatible = "fsl,imx6q-flexcan";
reg = <0x02090000 0x4000>;
interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks 1>, <&clks 2>;
clock-names = "ipg", "per";
fsl,stop-mode = <&gpr 0x34 28>;
fsl,scu-index = /bits/ 8 <1>;
};
- |
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
can@2090000 {
compatible = "fsl,imx6q-flexcan";
reg = <0x02090000 0x4000>;
interrupts = <0 110 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&clks 1>, <&clks 2>;
clock-names = "ipg", "per";
fsl,stop-mode = <&gpr 0x34 28>;
termination-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
termination-ohms = <120>;
};
|
