diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt')
| -rw-r--r-- | Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt | 78 |
1 files changed, 78 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt new file mode 100644 index 000000000..cb3342118 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -0,0 +1,78 @@ +* Freescale i.MX6 PCIe interface + +This PCIe host controller is based on the Synopsys DesignWare PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: + - "fsl,imx6q-pcie" + - "fsl,imx6sx-pcie", + - "fsl,imx6qp-pcie" + - "fsl,imx7d-pcie" +- reg: base address and length of the PCIe controller +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + - "msi": The interrupt that is asserted when an MSI is received +- clock-names: Must include the following additional entries: + - "pcie_phy" + +Optional properties: +- fsl,tx-deemph-gen1: Gen1 De-emphasis value. Default: 0 +- fsl,tx-deemph-gen2-3p5db: Gen2 (3.5db) De-emphasis value. Default: 0 +- fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20 +- fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127 +- fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127 +- fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for + gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs + do not meet gen2 jitter requirements and thus for gen2 capability a gen2 + compliant clock generator should be used and configured. +- reset-gpio: Should specify the GPIO for controlling the PCI bus device reset + signal. It's not polarity aware and defaults to active-low reset sequence + (L=reset state, H=operation state). +- reset-gpio-active-high: If present then the reset sequence using the GPIO + specified in the "reset-gpio" property is reversed (H=reset state, + L=operation state). +- vpcie-supply: Should specify the regulator in charge of PCIe port power. + The regulator will be enabled when initializing the PCIe host and + disabled either as part of the init process or when shutting down the + host. + +Additional required properties for imx6sx-pcie: +- clock names: Must include the following additional entries: + - "pcie_inbound_axi" +- power-domains: Must be set to a phandle pointing to the PCIE_PHY power domain + +Additional required properties for imx7d-pcie: +- power-domains: Must be set to a phandle pointing to PCIE_PHY power domain +- resets: Must contain phandles to PCIe-related reset lines exposed by SRC + IP block +- reset-names: Must contain the following entires: + - "pciephy" + - "apps" + +Example: + + pcie@01000000 { + compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; + reg = <0x01ffc000 0x04000>, + <0x01f00000 0x80000>; + reg-names = "dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 + 0x81000000 0 0 0x01f80000 0 0x00010000 + 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; + num-lanes = <1>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks 144>, <&clks 206>, <&clks 189>; + clock-names = "pcie", "pcie_bus", "pcie_phy"; + }; |