diff options
Diffstat (limited to 'Documentation/devicetree/bindings/pci')
47 files changed, 4514 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt b/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt new file mode 100644 index 000000000..b9165b724 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/83xx-512x-pci.txt @@ -0,0 +1,40 @@ +* Freescale 83xx and 512x PCI bridges + +Freescale 83xx and 512x SOCs include the same PCI bridge core. + +83xx/512x specific notes: +- reg: should contain two address length tuples + The first is for the internal PCI bridge registers + The second is for the PCI config space access registers + +Example (MPC8313ERDB) + pci0: pci@e0008500 { + cell-index = <1>; + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; + interrupt-map = < + /* IDSEL 0x0E -mini PCI */ + 0x7000 0x0 0x0 0x1 &ipic 18 0x8 + 0x7000 0x0 0x0 0x2 &ipic 18 0x8 + 0x7000 0x0 0x0 0x3 &ipic 18 0x8 + 0x7000 0x0 0x0 0x4 &ipic 18 0x8 + + /* IDSEL 0x0F - PCI slot */ + 0x7800 0x0 0x0 0x1 &ipic 17 0x8 + 0x7800 0x0 0x0 0x2 &ipic 18 0x8 + 0x7800 0x0 0x0 0x3 &ipic 17 0x8 + 0x7800 0x0 0x0 0x4 &ipic 18 0x8>; + interrupt-parent = <&ipic>; + interrupts = <66 0x8>; + bus-range = <0x0 0x0>; + ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000 + 0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000 + 0x01000000 0x0 0x00000000 0xe2000000 0x0 0x00100000>; + clock-frequency = <66666666>; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0xe0008500 0x100 /* internal registers */ + 0xe0008300 0x8>; /* config space access registers */ + compatible = "fsl,mpc8349-pci"; + device_type = "pci"; + }; diff --git a/Documentation/devicetree/bindings/pci/aardvark-pci.txt b/Documentation/devicetree/bindings/pci/aardvark-pci.txt new file mode 100644 index 000000000..310ef7145 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/aardvark-pci.txt @@ -0,0 +1,55 @@ +Aardvark PCIe controller + +This PCIe controller is used on the Marvell Armada 3700 ARM64 SoC. + +The Device Tree node describing an Aardvark PCIe controller must +contain the following properties: + + - compatible: Should be "marvell,armada-3700-pcie" + - reg: range of registers for the PCIe controller + - interrupts: the interrupt line of the PCIe controller + - #address-cells: set to <3> + - #size-cells: set to <2> + - device_type: set to "pci" + - ranges: ranges for the PCI memory and I/O regions + - #interrupt-cells: set to <1> + - msi-controller: indicates that the PCIe controller can itself + handle MSI interrupts + - msi-parent: pointer to the MSI controller to be used + - interrupt-map-mask and interrupt-map: standard PCI properties to + define the mapping of the PCIe interface to interrupt numbers. + - bus-range: PCI bus numbers covered + +In addition, the Device Tree describing an Aardvark PCIe controller +must include a sub-node that describes the legacy interrupt controller +built into the PCIe controller. This sub-node must have the following +properties: + + - interrupt-controller + - #interrupt-cells: set to <1> + +Example: + + pcie0: pcie@d0070000 { + compatible = "marvell,armada-3700-pcie"; + device_type = "pci"; + reg = <0 0xd0070000 0 0x20000>; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x00 0xff>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; + #interrupt-cells = <1>; + msi-controller; + msi-parent = <&pcie0>; + ranges = <0x82000000 0 0xe8000000 0 0xe8000000 0 0x1000000 /* Port 0 MEM */ + 0x81000000 0 0xe9000000 0 0xe9000000 0 0x10000>; /* Port 0 IO*/ + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 0>, + <0 0 0 2 &pcie_intc 1>, + <0 0 0 3 &pcie_intc 2>, + <0 0 0 4 &pcie_intc 3>; + pcie_intc: interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/altera-pcie-msi.txt b/Documentation/devicetree/bindings/pci/altera-pcie-msi.txt new file mode 100644 index 000000000..9514c327d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/altera-pcie-msi.txt @@ -0,0 +1,27 @@ +* Altera PCIe MSI controller + +Required properties: +- compatible: should contain "altr,msi-1.0" +- reg: specifies the physical base address of the controller and + the length of the memory mapped region. +- reg-names: must include the following entries: + "csr": CSR registers + "vector_slave": vectors slave port region +- interrupts: specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends on the + parent interrupt controller. +- num-vectors: number of vectors, range 1 to 32. +- msi-controller: indicates that this is MSI controller node + + +Example +msi0: msi@0xFF200000 { + compatible = "altr,msi-1.0"; + reg = <0xFF200000 0x00000010 + 0xFF200010 0x00000080>; + reg-names = "csr", "vector_slave"; + interrupt-parent = <&hps_0_arm_gic_0>; + interrupts = <0 42 4>; + msi-controller; + num-vectors = <32>; +}; diff --git a/Documentation/devicetree/bindings/pci/altera-pcie.txt b/Documentation/devicetree/bindings/pci/altera-pcie.txt new file mode 100644 index 000000000..6c396f17c --- /dev/null +++ b/Documentation/devicetree/bindings/pci/altera-pcie.txt @@ -0,0 +1,48 @@ +* Altera PCIe controller + +Required properties: +- compatible : should contain "altr,pcie-root-port-1.0" +- reg: a list of physical base address and length for TXS and CRA. +- reg-names: must include the following entries: + "Txs": TX slave port region + "Cra": Control register access region +- interrupts: specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends + on the parent interrupt controller. +- device_type: must be "pci" +- #address-cells: set to <3> +- #size-cells: set to <2> +- #interrupt-cells: set to <1> +- ranges: describes the translation of addresses for root ports and + standard PCI regions. +- interrupt-map-mask and interrupt-map: standard PCI properties to define the + mapping of the PCIe interface to interrupt numbers. + +Optional properties: +- msi-parent: Link to the hardware entity that serves as the MSI controller + for this PCIe controller. +- bus-range: PCI bus numbers covered + +Example + pcie_0: pcie@c00000000 { + compatible = "altr,pcie-root-port-1.0"; + reg = <0xc0000000 0x20000000>, + <0xff220000 0x00004000>; + reg-names = "Txs", "Cra"; + interrupt-parent = <&hps_0_arm_gic_0>; + interrupts = <0 40 4>; + interrupt-controller; + #interrupt-cells = <1>; + bus-range = <0x0 0xFF>; + device_type = "pci"; + msi-parent = <&msi_to_gic_gen_0>; + #address-cells = <3>; + #size-cells = <2>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_0 1>, + <0 0 0 2 &pcie_0 2>, + <0 0 0 3 &pcie_0 3>, + <0 0 0 4 &pcie_0 4>; + ranges = <0x82000000 0x00000000 0x00000000 0xc0000000 0x00000000 0x10000000 + 0x82000000 0x00000000 0x10000000 0xd0000000 0x00000000 0x10000000>; + }; diff --git a/Documentation/devicetree/bindings/pci/arm,juno-r1-pcie.txt b/Documentation/devicetree/bindings/pci/arm,juno-r1-pcie.txt new file mode 100644 index 000000000..f7514c170 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/arm,juno-r1-pcie.txt @@ -0,0 +1,10 @@ +* ARM Juno R1 PCIe interface + +This PCIe host controller is based on PLDA XpressRICH3-AXI IP +and thus inherits all the common properties defined in plda,xpressrich3-axi.txt +as well as the base properties defined in host-generic-pci.txt. + +Required properties: + - compatible: "arm,juno-r1-pcie" + - dma-coherent: The host controller bridges the AXI transactions into PCIe bus + in a manner that makes the DMA operations to appear coherent to the CPUs. diff --git a/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt new file mode 100644 index 000000000..979dc7b6c --- /dev/null +++ b/Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt @@ -0,0 +1,50 @@ +* Axis ARTPEC-6 PCIe interface + +This PCIe host controller is based on the Synopsys DesignWare PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "axis,artpec6-pcie", "snps,dw-pcie" for ARTPEC-6 in RC mode; + "axis,artpec6-pcie-ep", "snps,dw-pcie" for ARTPEC-6 in EP mode; + "axis,artpec7-pcie", "snps,dw-pcie" for ARTPEC-7 in RC mode; + "axis,artpec7-pcie-ep", "snps,dw-pcie" for ARTPEC-7 in EP mode; +- reg: base addresses and lengths of the PCIe controller (DBI), + the PHY controller, and configuration address space. +- reg-names: Must include the following entries: + - "dbi" + - "phy" + - "config" +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + - "msi": The interrupt that is asserted when an MSI is received +- axis,syscon-pcie: A phandle pointing to the ARTPEC-6 system controller, + used to enable and control the Synopsys IP. + +Example: + + pcie@f8050000 { + compatible = "axis,artpec6-pcie", "snps,dw-pcie"; + reg = <0xf8050000 0x2000 + 0xf8040000 0x1000 + 0xc0000000 0x2000>; + reg-names = "dbi", "phy", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + /* downstream I/O */ + ranges = <0x81000000 0 0 0xc0002000 0 0x00010000 + /* non-prefetchable memory */ + 0x82000000 0 0xc0012000 0xc0012000 0 0x1ffee000>; + num-lanes = <2>; + bus-range = <0x00 0xff>; + interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>; + axis,syscon-pcie = <&syscon>; + }; diff --git a/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt new file mode 100644 index 000000000..df065aa53 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/brcm,iproc-pcie.txt @@ -0,0 +1,133 @@ +* Broadcom iProc PCIe controller with the platform bus interface + +Required properties: +- compatible: + "brcm,iproc-pcie" for the first generation of PAXB based controller, +used in SoCs including NSP, Cygnus, NS2, and Pegasus + "brcm,iproc-pcie-paxb-v2" for the second generation of PAXB-based +controllers, used in Stingray + "brcm,iproc-pcie-paxc" for the first generation of PAXC based +controller, used in NS2 + "brcm,iproc-pcie-paxc-v2" for the second generation of PAXC based +controller, used in Stingray + PAXB-based root complex is used for external endpoint devices. PAXC-based +root complex is connected to emulated endpoint devices internal to the ASIC +- reg: base address and length of the PCIe controller I/O register space +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map, standard PCI properties to define the + mapping of the PCIe interface to interrupt numbers +- linux,pci-domain: PCI domain ID. Should be unique for each host controller +- bus-range: PCI bus numbers covered +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions + +Optional properties: +- phys: phandle of the PCIe PHY device +- phy-names: must be "pcie-phy" +- dma-coherent: present if DMA operations are coherent +- dma-ranges: Some PAXB-based root complexes do not have inbound mapping done + by the ASIC after power on reset. In this case, SW is required to configure +the mapping, based on inbound memory regions specified by this property. + +- brcm,pcie-ob: Some iProc SoCs do not have the outbound address mapping done +by the ASIC after power on reset. In this case, SW needs to configure it + +If the brcm,pcie-ob property is present, the following properties become +effective: + +Required: +- brcm,pcie-ob-axi-offset: The offset from the AXI address to the internal +address used by the iProc PCIe core (not the PCIe address) + +MSI support (optional): + +For older platforms without MSI integrated in the GIC, iProc PCIe core provides +an event queue based MSI support. The iProc MSI uses host memories to store +MSI posted writes in the event queues + +On newer iProc platforms, gicv2m or gicv3-its based MSI support should be used + +- msi-map: Maps a Requester ID to an MSI controller and associated MSI +sideband data + +- msi-parent: Link to the device node of the MSI controller, used when no MSI +sideband data is passed between the iProc PCIe controller and the MSI +controller + +Refer to the following binding documents for more detailed description on +the use of 'msi-map' and 'msi-parent': + Documentation/devicetree/bindings/pci/pci-msi.txt + Documentation/devicetree/bindings/interrupt-controller/msi.txt + +When the iProc event queue based MSI is used, one needs to define the +following properties in the MSI device node: +- compatible: Must be "brcm,iproc-msi" +- msi-controller: claims itself as an MSI controller +- interrupts: List of interrupt IDs from its parent interrupt device + +Optional properties: +- brcm,pcie-msi-inten: Needs to be present for some older iProc platforms that +require the interrupt enable registers to be set explicitly to enable MSI + +Example: + pcie0: pcie@18012000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18012000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 100 IRQ_TYPE_NONE>; + + linux,pci-domain = <0>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x28000000 0 0x00010000 + 0x82000000 0 0x20000000 0x20000000 0 0x04000000>; + + phys = <&phy 0 5>; + phy-names = "pcie-phy"; + + brcm,pcie-ob; + brcm,pcie-ob-axi-offset = <0x00000000>; + + msi-parent = <&msi0>; + + /* iProc event queue based MSI */ + msi0: msi@18012000 { + compatible = "brcm,iproc-msi"; + msi-controller; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 96 IRQ_TYPE_NONE>, + <GIC_SPI 97 IRQ_TYPE_NONE>, + <GIC_SPI 98 IRQ_TYPE_NONE>, + <GIC_SPI 99 IRQ_TYPE_NONE>, + }; + }; + + pcie1: pcie@18013000 { + compatible = "brcm,iproc-pcie"; + reg = <0x18013000 0x1000>; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 106 IRQ_TYPE_NONE>; + + linux,pci-domain = <1>; + + bus-range = <0x00 0xff>; + + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x48000000 0 0x00010000 + 0x82000000 0 0x40000000 0x40000000 0 0x04000000>; + + phys = <&phy 1 6>; + phy-names = "pcie-phy"; + }; diff --git a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.txt b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.txt new file mode 100644 index 000000000..4a0475e2b --- /dev/null +++ b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-ep.txt @@ -0,0 +1,27 @@ +* Cadence PCIe endpoint controller + +Required properties: +- compatible: Should contain "cdns,cdns-pcie-ep" to identify the IP used. +- reg: Should contain the controller register base address and AXI interface + region base address respectively. +- reg-names: Must be "reg" and "mem" respectively. +- cdns,max-outbound-regions: Set to maximum number of outbound regions + +Optional properties: +- max-functions: Maximum number of functions that can be configured (default 1). +- phys: From PHY bindings: List of Generic PHY phandles. One per lane if more + than one in the list. If only one PHY listed it must manage all lanes. +- phy-names: List of names to identify the PHY. + +Example: + +pcie@fc000000 { + compatible = "cdns,cdns-pcie-ep"; + reg = <0x0 0xfc000000 0x0 0x01000000>, + <0x0 0x80000000 0x0 0x40000000>; + reg-names = "reg", "mem"; + cdns,max-outbound-regions = <16>; + max-functions = /bits/ 8 <8>; + phys = <&ep_phy0 &ep_phy1>; + phy-names = "pcie-lane0","pcie-lane1"; +}; diff --git a/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.txt b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.txt new file mode 100644 index 000000000..91de69c71 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/cdns,cdns-pcie-host.txt @@ -0,0 +1,66 @@ +* Cadence PCIe host controller + +This PCIe controller inherits the base properties defined in +host-generic-pci.txt. + +Required properties: +- compatible: Should contain "cdns,cdns-pcie-host" to identify the IP used. +- reg: Should contain the controller register base address, PCIe configuration + window base address, and AXI interface region base address respectively. +- reg-names: Must be "reg", "cfg" and "mem" respectively. +- #address-cells: Set to <3> +- #size-cells: Set to <2> +- device_type: Set to "pci" +- ranges: Ranges for the PCI memory and I/O regions +- #interrupt-cells: Set to <1> +- interrupt-map-mask and interrupt-map: Standard PCI properties to define the + mapping of the PCIe interface to interrupt numbers. + +Optional properties: +- cdns,max-outbound-regions: Set to maximum number of outbound regions + (default 32) +- cdns,no-bar-match-nbits: Set into the no BAR match register to configure the + number of least significant bits kept during inbound (PCIe -> AXI) address + translations (default 32) +- vendor-id: The PCI vendor ID (16 bits, default is design dependent) +- device-id: The PCI device ID (16 bits, default is design dependent) +- phys: From PHY bindings: List of Generic PHY phandles. One per lane if more + than one in the list. If only one PHY listed it must manage all lanes. +- phy-names: List of names to identify the PHY. + +Example: + +pcie@fb000000 { + compatible = "cdns,cdns-pcie-host"; + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0xff>; + linux,pci-domain = <0>; + cdns,max-outbound-regions = <16>; + cdns,no-bar-match-nbits = <32>; + vendor-id = /bits/ 16 <0x17cd>; + device-id = /bits/ 16 <0x0200>; + + reg = <0x0 0xfb000000 0x0 0x01000000>, + <0x0 0x41000000 0x0 0x00001000>, + <0x0 0x40000000 0x0 0x04000000>; + reg-names = "reg", "cfg", "mem"; + + ranges = <0x02000000 0x0 0x42000000 0x0 0x42000000 0x0 0x1000000>, + <0x01000000 0x0 0x43000000 0x0 0x43000000 0x0 0x0010000>; + + #interrupt-cells = <0x1>; + + interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0x0 0x0 14 0x1 + 0x0 0x0 0x0 0x2 &gic 0x0 0x0 0x0 15 0x1 + 0x0 0x0 0x0 0x3 &gic 0x0 0x0 0x0 16 0x1 + 0x0 0x0 0x0 0x4 &gic 0x0 0x0 0x0 17 0x1>; + + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + + msi-parent = <&its_pci>; + + phys = <&pcie_phy0>; + phy-names = "pcie-phy"; +}; diff --git a/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt b/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt new file mode 100644 index 000000000..515b2f954 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/designware-pcie-ecam.txt @@ -0,0 +1,42 @@ +* Synopsys DesignWare PCIe root complex in ECAM shift mode + +In some cases, firmware may already have configured the Synopsys DesignWare +PCIe controller in RC mode with static ATU window mappings that cover all +config, MMIO and I/O spaces in a [mostly] ECAM compatible fashion. +In this case, there is no need for the OS to perform any low level setup +of clocks, PHYs or device registers, nor is there any reason for the driver +to reconfigure ATU windows for config and/or IO space accesses at runtime. + +In cases where the IP was synthesized with a minimum ATU window size of +64 KB, it cannot be supported by the generic ECAM driver, because it +requires special config space accessors that filter accesses to device #1 +and beyond on the first bus. + +Required properties: +- compatible: "marvell,armada8k-pcie-ecam" or + "socionext,synquacer-pcie-ecam" or + "snps,dw-pcie-ecam" (must be preceded by a more specific match) + +Please refer to the binding document of "pci-host-ecam-generic" in the +file host-generic-pci.txt for a description of the remaining required +and optional properties. + +Example: + + pcie1: pcie@7f000000 { + compatible = "socionext,synquacer-pcie-ecam", "snps,dw-pcie-ecam"; + device_type = "pci"; + reg = <0x0 0x7f000000 0x0 0xf00000>; + bus-range = <0x0 0xe>; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x1000000 0x00 0x00010000 0x00 0x7ff00000 0x0 0x00010000>, + <0x2000000 0x00 0x70000000 0x00 0x70000000 0x0 0x0f000000>, + <0x3000000 0x3f 0x00000000 0x3f 0x00000000 0x1 0x00000000>; + + #interrupt-cells = <0x1>; + interrupt-map-mask = <0x0 0x0 0x0 0x0>; + interrupt-map = <0x0 0x0 0x0 0x0 &gic 0x0 0x0 0x0 182 0x4>; + msi-map = <0x0 &its 0x0 0x10000>; + dma-coherent; + }; diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt new file mode 100644 index 000000000..c124f9bc1 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt @@ -0,0 +1,70 @@ +* Synopsys DesignWare PCIe interface + +Required properties: +- compatible: + "snps,dw-pcie" for RC mode; + "snps,dw-pcie-ep" for EP mode; +- reg: Should contain the configuration address space. +- reg-names: Must be "config" for the PCIe configuration space. + (The old way of getting the configuration address space from "ranges" + is deprecated and should be avoided.) +- num-lanes: number of lanes to use +RC mode: +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI + properties to define the mapping of the PCIe interface to interrupt + numbers. +EP mode: +- num-ib-windows: number of inbound address translation windows +- num-ob-windows: number of outbound address translation windows + +Optional properties: +- num-lanes: number of lanes to use (this property should be specified unless + the link is brought already up in BIOS) +- reset-gpio: GPIO pin number of power good signal +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "pcie" + - "pcie_bus" +RC mode: +- num-viewport: number of view ports configured in hardware. If a platform + does not specify it, the driver assumes 2. +- bus-range: PCI bus numbers covered (it is recommended for new devicetrees + to specify this property, to keep backwards compatibility a range of + 0x00-0xff is assumed if not present) + +EP mode: +- max-functions: maximum number of functions that can be configured + +Example configuration: + + pcie: pcie@dfc00000 { + compatible = "snps,dw-pcie"; + reg = <0xdfc00000 0x0001000>, /* IP registers */ + <0xd0000000 0x0002000>; /* Configuration space */ + reg-names = "dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0x00000000 0xde000000 0 0x00010000 + 0x82000000 0 0xd0400000 0xd0400000 0 0x0d000000>; + interrupts = <25>, <24>; + #interrupt-cells = <1>; + num-lanes = <1>; + }; +or + pcie: pcie@dfc00000 { + compatible = "snps,dw-pcie-ep"; + reg = <0xdfc00000 0x0001000>, /* IP registers 1 */ + <0xdfc01000 0x0001000>, /* IP registers 2 */ + <0xd0000000 0x2000000>; /* Configuration space */ + reg-names = "dbi", "dbi2", "addr_space"; + num-ib-windows = <6>; + num-ob-windows = <2>; + num-lanes = <1>; + }; diff --git a/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt b/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt new file mode 100644 index 000000000..5f8cb4962 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/faraday,ftpci100.txt @@ -0,0 +1,135 @@ +Faraday Technology FTPCI100 PCI Host Bridge + +This PCI bridge is found inside that Cortina Systems Gemini SoC platform and +is a generic IP block from Faraday Technology. It exists in two variants: +plain and dual PCI. The plain version embeds a cascading interrupt controller +into the host bridge. The dual version routes the interrupts to the host +chips interrupt controller. + +The host controller appear on the PCI bus with vendor ID 0x159b (Faraday +Technology) and product ID 0x4321. + +Mandatory properties: + +- compatible: ranging from specific to generic, should be one of + "cortina,gemini-pci", "faraday,ftpci100" + "cortina,gemini-pci-dual", "faraday,ftpci100-dual" + "faraday,ftpci100" + "faraday,ftpci100-dual" +- reg: memory base and size for the host bridge +- #address-cells: set to <3> +- #size-cells: set to <2> +- #interrupt-cells: set to <1> +- bus-range: set to <0x00 0xff> +- device_type, set to "pci" +- ranges: see pci.txt +- interrupt-map-mask: see pci.txt +- interrupt-map: see pci.txt +- dma-ranges: three ranges for the inbound memory region. The ranges must + be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB, + 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as + pre-fetchable. + +Optional properties: +- clocks: when present, this should contain the peripheral clock (PCLK) and the + PCI clock (PCICLK). If these are not present, they are assumed to be + hard-wired enabled and always on. The PCI clock will be 33 or 66 MHz. +- clock-names: when present, this should contain "PCLK" for the peripheral + clock and "PCICLK" for the PCI-side clock. + +Mandatory subnodes: +- For "faraday,ftpci100" a node representing the interrupt-controller inside the + host bridge is mandatory. It has the following mandatory properties: + - interrupt: see interrupt-controller/interrupts.txt + - interrupt-controller: see interrupt-controller/interrupts.txt + - #address-cells: set to <0> + - #interrupt-cells: set to <1> + +I/O space considerations: + +The plain variant has 128MiB of non-prefetchable memory space, whereas the +"dual" variant has 64MiB. Take this into account when describing the ranges. + +Interrupt map considerations: + +The "dual" variant will get INT A, B, C, D from the system interrupt controller +and should point to respective interrupt in that controller in its +interrupt-map. + +The code which is the only documentation of how the Faraday PCI (the non-dual +variant) interrupts assigns the default interrupt mapping/swizzling has +typically been like this, doing the swizzling on the interrupt controller side +rather than in the interconnect: + +interrupt-map-mask = <0xf800 0 0 7>; +interrupt-map = + <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */ + <0x4800 0 0 2 &pci_intc 1>, + <0x4800 0 0 3 &pci_intc 2>, + <0x4800 0 0 4 &pci_intc 3>, + <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */ + <0x5000 0 0 2 &pci_intc 2>, + <0x5000 0 0 3 &pci_intc 3>, + <0x5000 0 0 4 &pci_intc 0>, + <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */ + <0x5800 0 0 2 &pci_intc 3>, + <0x5800 0 0 3 &pci_intc 0>, + <0x5800 0 0 4 &pci_intc 1>, + <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */ + <0x6000 0 0 2 &pci_intc 0>, + <0x6000 0 0 3 &pci_intc 1>, + <0x6000 0 0 4 &pci_intc 2>; + +Example: + +pci@50000000 { + compatible = "cortina,gemini-pci", "faraday,ftpci100"; + reg = <0x50000000 0x100>; + interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, /* PCI A */ + <26 IRQ_TYPE_LEVEL_HIGH>, /* PCI B */ + <27 IRQ_TYPE_LEVEL_HIGH>, /* PCI C */ + <28 IRQ_TYPE_LEVEL_HIGH>; /* PCI D */ + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + + bus-range = <0x00 0xff>; + ranges = /* 1MiB I/O space 0x50000000-0x500fffff */ + <0x01000000 0 0 0x50000000 0 0x00100000>, + /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */ + <0x02000000 0 0x58000000 0x58000000 0 0x08000000>; + + /* DMA ranges */ + dma-ranges = + /* 128MiB at 0x00000000-0x07ffffff */ + <0x02000000 0 0x00000000 0x00000000 0 0x08000000>, + /* 64MiB at 0x00000000-0x03ffffff */ + <0x02000000 0 0x00000000 0x00000000 0 0x04000000>, + /* 64MiB at 0x00000000-0x03ffffff */ + <0x02000000 0 0x00000000 0x00000000 0 0x04000000>; + + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = + <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */ + <0x4800 0 0 2 &pci_intc 1>, + <0x4800 0 0 3 &pci_intc 2>, + <0x4800 0 0 4 &pci_intc 3>, + <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */ + <0x5000 0 0 2 &pci_intc 2>, + <0x5000 0 0 3 &pci_intc 3>, + <0x5000 0 0 4 &pci_intc 0>, + <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */ + <0x5800 0 0 2 &pci_intc 3>, + <0x5800 0 0 3 &pci_intc 0>, + <0x5800 0 0 4 &pci_intc 1>, + <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */ + <0x6000 0 0 2 &pci_intc 0>, + <0x6000 0 0 3 &pci_intc 0>, + <0x6000 0 0 4 &pci_intc 0>; + pci_intc: interrupt-controller { + interrupt-parent = <&intcon>; + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt new file mode 100644 index 000000000..cb3342118 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt @@ -0,0 +1,78 @@ +* Freescale i.MX6 PCIe interface + +This PCIe host controller is based on the Synopsys DesignWare PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: + - "fsl,imx6q-pcie" + - "fsl,imx6sx-pcie", + - "fsl,imx6qp-pcie" + - "fsl,imx7d-pcie" +- reg: base address and length of the PCIe controller +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + - "msi": The interrupt that is asserted when an MSI is received +- clock-names: Must include the following additional entries: + - "pcie_phy" + +Optional properties: +- fsl,tx-deemph-gen1: Gen1 De-emphasis value. Default: 0 +- fsl,tx-deemph-gen2-3p5db: Gen2 (3.5db) De-emphasis value. Default: 0 +- fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20 +- fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127 +- fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127 +- fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for + gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs + do not meet gen2 jitter requirements and thus for gen2 capability a gen2 + compliant clock generator should be used and configured. +- reset-gpio: Should specify the GPIO for controlling the PCI bus device reset + signal. It's not polarity aware and defaults to active-low reset sequence + (L=reset state, H=operation state). +- reset-gpio-active-high: If present then the reset sequence using the GPIO + specified in the "reset-gpio" property is reversed (H=reset state, + L=operation state). +- vpcie-supply: Should specify the regulator in charge of PCIe port power. + The regulator will be enabled when initializing the PCIe host and + disabled either as part of the init process or when shutting down the + host. + +Additional required properties for imx6sx-pcie: +- clock names: Must include the following additional entries: + - "pcie_inbound_axi" +- power-domains: Must be set to a phandle pointing to the PCIE_PHY power domain + +Additional required properties for imx7d-pcie: +- power-domains: Must be set to a phandle pointing to PCIE_PHY power domain +- resets: Must contain phandles to PCIe-related reset lines exposed by SRC + IP block +- reset-names: Must contain the following entires: + - "pciephy" + - "apps" + +Example: + + pcie@01000000 { + compatible = "fsl,imx6q-pcie", "snps,dw-pcie"; + reg = <0x01ffc000 0x04000>, + <0x01f00000 0x80000>; + reg-names = "dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000 + 0x81000000 0 0 0x01f80000 0 0x00010000 + 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>; + num-lanes = <1>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, + <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&clks 144>, <&clks 206>, <&clks 189>; + clock-names = "pcie", "pcie_bus", "pcie_phy"; + }; diff --git a/Documentation/devicetree/bindings/pci/fsl,pci.txt b/Documentation/devicetree/bindings/pci/fsl,pci.txt new file mode 100644 index 000000000..d8ac4a768 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/fsl,pci.txt @@ -0,0 +1,27 @@ +* Bus Enumeration by Freescale PCI-X Agent + +Typically any Freescale PCI-X bridge hardware strapped into Agent mode +is prevented from enumerating the bus. The PrPMC form-factor requires +all mezzanines to be PCI-X Agents, but one per system may still +enumerate the bus. + +The property defined below will allow a PCI-X bridge to be used for bus +enumeration despite being strapped into Agent mode. + +Required properties: +- fsl,pci-agent-force-enum : There is no value associated with this + property. The property itself is treated as a boolean. + +Example: + + /* PCI-X bridge known to be PrPMC Monarch */ + pci0: pci@ef008000 { + fsl,pci-agent-force-enum; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + compatible = "fsl,mpc8540-pcix", "fsl,mpc8540-pci"; + device_type = "pci"; + ... + ... + }; diff --git a/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt new file mode 100644 index 000000000..760b4d740 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt @@ -0,0 +1,69 @@ +HiSilicon STB PCIe host bridge DT description + +The HiSilicon STB PCIe host controller is based on the DesignWare PCIe core. +It shares common functions with the DesignWare PCIe core driver and inherits +common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt. + +Additional properties are described here: + +Required properties +- compatible: Should be one of the following strings: + "hisilicon,hi3798cv200-pcie" +- reg: Should contain sysctl, rc_dbi, config registers location and length. +- reg-names: Must include the following entries: + "control": control registers of PCIe controller; + "rc-dbi": configuration space of PCIe controller; + "config": configuration transaction space of PCIe controller. +- bus-range: PCI bus numbers covered. +- interrupts: MSI interrupt. +- interrupt-names: Must include "msi" entries. +- clocks: List of phandle and clock specifier pairs as listed in clock-names + property. +- clock-name: Must include the following entries: + "aux": auxiliary gate clock; + "pipe": pipe gate clock; + "sys": sys gate clock; + "bus": bus gate clock. +- resets: List of phandle and reset specifier pairs as listed in reset-names + property. +- reset-names: Must include the following entries: + "soft": soft reset; + "sys": sys reset; + "bus": bus reset. + +Optional properties: +- reset-gpios: The gpio to generate PCIe PERST# assert and deassert signal. +- vpcie-supply: The regulator in charge of PCIe port power. +- phys: List of phandle and phy mode specifier, should be 0. +- phy-names: Must be "phy". + +Example: + pcie@f9860000 { + compatible = "hisilicon,hi3798cv200-pcie"; + reg = <0xf9860000 0x1000>, + <0xf0000000 0x2000>, + <0xf2000000 0x01000000>; + reg-names = "control", "rc-dbi", "config"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + bus-range = <0 15>; + num-lanes = <1>; + ranges=<0x81000000 0 0 0xf4000000 0 0x00010000 + 0x82000000 0 0xf3000000 0xf3000000 0 0x01000000>; + interrupts = <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&crg PCIE_AUX_CLK>, + <&crg PCIE_PIPE_CLK>, + <&crg PCIE_SYS_CLK>, + <&crg PCIE_BUS_CLK>; + clock-names = "aux", "pipe", "sys", "bus"; + resets = <&crg 0x18c 6>, <&crg 0x18c 5>, <&crg 0x18c 4>; + reset-names = "soft", "sys", "bus"; + phys = <&combphy1 PHY_TYPE_PCIE>; + phy-names = "phy"; + }; diff --git a/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt new file mode 100644 index 000000000..0dcb87d65 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/hisilicon-pcie.txt @@ -0,0 +1,85 @@ +HiSilicon Hip05 and Hip06 PCIe host bridge DT description + +HiSilicon PCIe host controller is based on the Synopsys DesignWare PCI core. +It shares common functions with the PCIe DesignWare core driver and inherits +common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt. + +Additional properties are described here: + +Required properties +- compatible: Should contain "hisilicon,hip05-pcie" or "hisilicon,hip06-pcie". +- reg: Should contain rc_dbi, config registers location and length. +- reg-names: Must include the following entries: + "rc_dbi": controller configuration registers; + "config": PCIe configuration space registers. +- msi-parent: Should be its_pcie which is an ITS receiving MSI interrupts. +- port-id: Should be 0, 1, 2 or 3. + +Optional properties: +- status: Either "ok" or "disabled". +- dma-coherent: Present if DMA operations are coherent. + +Hip05 Example (note that Hip06 is the same except compatible): + pcie@b0080000 { + compatible = "hisilicon,hip05-pcie", "snps,dw-pcie"; + reg = <0 0xb0080000 0 0x10000>, <0x220 0x00000000 0 0x2000>; + reg-names = "rc_dbi", "config"; + bus-range = <0 15>; + msi-parent = <&its_pcie>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + dma-coherent; + ranges = <0x82000000 0 0x00000000 0x220 0x00000000 0 0x10000000>; + num-lanes = <8>; + port-id = <1>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = <0x0 0 0 1 &mbigen_pcie 1 10 + 0x0 0 0 2 &mbigen_pcie 2 11 + 0x0 0 0 3 &mbigen_pcie 3 12 + 0x0 0 0 4 &mbigen_pcie 4 13>; + }; + +HiSilicon Hip06/Hip07 PCIe host bridge DT (almost-ECAM) description. + +Some BIOSes place the host controller in a mode where it is ECAM +compliant for all devices other than the root complex. In such cases, +the host controller should be described as below. + +The properties and their meanings are identical to those described in +host-generic-pci.txt except as listed below. + +Properties of the host controller node that differ from +host-generic-pci.txt: + +- compatible : Must be "hisilicon,hip06-pcie-ecam", or + "hisilicon,hip07-pcie-ecam" + +- reg : Two entries: First the ECAM configuration space for any + other bus underneath the root bus. Second, the base + and size of the HiSilicon host bridge registers include + the RC's own config space. + +Example: + pcie0: pcie@a0090000 { + compatible = "hisilicon,hip06-pcie-ecam"; + reg = <0 0xb0000000 0 0x2000000>, /* ECAM configuration space */ + <0 0xa0090000 0 0x10000>; /* host bridge registers */ + bus-range = <0 31>; + msi-map = <0x0000 &its_dsa 0x0000 0x2000>; + msi-map-mask = <0xffff>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + dma-coherent; + ranges = <0x02000000 0 0xb2000000 0x0 0xb2000000 0 0x5ff0000 + 0x01000000 0 0 0 0xb7ff0000 0 0x10000>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = <0x0 0 0 1 &mbigen_pcie0 650 4 + 0x0 0 0 2 &mbigen_pcie0 650 4 + 0x0 0 0 3 &mbigen_pcie0 650 4 + 0x0 0 0 4 &mbigen_pcie0 650 4>; + }; diff --git a/Documentation/devicetree/bindings/pci/host-generic-pci.txt b/Documentation/devicetree/bindings/pci/host-generic-pci.txt new file mode 100644 index 000000000..3f1d3fca6 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/host-generic-pci.txt @@ -0,0 +1,101 @@ +* Generic PCI host controller + +Firmware-initialised PCI host controllers and PCI emulations, such as the +virtio-pci implementations found in kvmtool and other para-virtualised +systems, do not require driver support for complexities such as regulator +and clock management. In fact, the controller may not even require the +configuration of a control interface by the operating system, instead +presenting a set of fixed windows describing a subset of IO, Memory and +Configuration Spaces. + +Such a controller can be described purely in terms of the standardized device +tree bindings communicated in pci.txt: + + +Properties of the host controller node: + +- compatible : Must be "pci-host-cam-generic" or "pci-host-ecam-generic" + depending on the layout of configuration space (CAM vs + ECAM respectively). + +- device_type : Must be "pci". + +- ranges : As described in IEEE Std 1275-1994, but must provide + at least a definition of non-prefetchable memory. One + or both of prefetchable Memory and IO Space may also + be provided. + +- bus-range : Optional property (also described in IEEE Std 1275-1994) + to indicate the range of bus numbers for this controller. + If absent, defaults to <0 255> (i.e. all buses). + +- #address-cells : Must be 3. + +- #size-cells : Must be 2. + +- reg : The Configuration Space base address and size, as accessed + from the parent bus. The base address corresponds to + the first bus in the "bus-range" property. If no + "bus-range" is specified, this will be bus 0 (the default). + +Properties of the /chosen node: + +- linux,pci-probe-only + : Optional property which takes a single-cell argument. + If '0', then Linux will assign devices in its usual manner, + otherwise it will not try to assign devices and instead use + them as they are configured already. + +Configuration Space is assumed to be memory-mapped (as opposed to being +accessed via an ioport) and laid out with a direct correspondence to the +geography of a PCI bus address by concatenating the various components to +form an offset. + +For CAM, this 24-bit offset is: + + cfg_offset(bus, device, function, register) = + bus << 16 | device << 11 | function << 8 | register + +Whilst ECAM extends this by 4 bits to accommodate 4k of function space: + + cfg_offset(bus, device, function, register) = + bus << 20 | device << 15 | function << 12 | register + +Interrupt mapping is exactly as described in `Open Firmware Recommended +Practice: Interrupt Mapping' and requires the following properties: + +- #interrupt-cells : Must be 1 + +- interrupt-map : <see aforementioned specification> + +- interrupt-map-mask : <see aforementioned specification> + + +Example: + +pci { + compatible = "pci-host-cam-generic" + device_type = "pci"; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x0 0x1>; + + // CPU_PHYSICAL(2) SIZE(2) + reg = <0x0 0x40000000 0x0 0x1000000>; + + // BUS_ADDRESS(3) CPU_PHYSICAL(2) SIZE(2) + ranges = <0x01000000 0x0 0x01000000 0x0 0x01000000 0x0 0x00010000>, + <0x02000000 0x0 0x41000000 0x0 0x41000000 0x0 0x3f000000>; + + + #interrupt-cells = <0x1>; + + // PCI_DEVICE(3) INT#(1) CONTROLLER(PHANDLE) CONTROLLER_DATA(3) + interrupt-map = < 0x0 0x0 0x0 0x1 &gic 0x0 0x4 0x1 + 0x800 0x0 0x0 0x1 &gic 0x0 0x5 0x1 + 0x1000 0x0 0x0 0x1 &gic 0x0 0x6 0x1 + 0x1800 0x0 0x0 0x1 &gic 0x0 0x7 0x1>; + + // PCI_DEVICE(3) INT#(1) + interrupt-map-mask = <0xf800 0x0 0x0 0x7>; +} diff --git a/Documentation/devicetree/bindings/pci/kirin-pcie.txt b/Documentation/devicetree/bindings/pci/kirin-pcie.txt new file mode 100644 index 000000000..6bbe43818 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/kirin-pcie.txt @@ -0,0 +1,50 @@ +HiSilicon Kirin SoCs PCIe host DT description + +Kirin PCIe host controller is based on the Synopsys DesignWare PCI core. +It shares common functions with the PCIe DesignWare core driver and +inherits common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt. + +Additional properties are described here: + +Required properties +- compatible: + "hisilicon,kirin960-pcie" for PCIe of Kirin960 SoC +- reg: Should contain rc_dbi, apb, phy, config registers location and length. +- reg-names: Must include the following entries: + "dbi": controller configuration registers; + "apb": apb Ctrl register defined by Kirin; + "phy": apb PHY register defined by Kirin; + "config": PCIe configuration space registers. +- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal. + +Optional properties: + +Example based on kirin960: + + pcie@f4000000 { + compatible = "hisilicon,kirin-pcie"; + reg = <0x0 0xf4000000 0x0 0x1000>, <0x0 0xff3fe000 0x0 0x1000>, + <0x0 0xf3f20000 0x0 0x40000>, <0x0 0xF4000000 0 0x2000>; + reg-names = "dbi","apb","phy", "config"; + bus-range = <0x0 0x1>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x02000000 0x0 0x00000000 0x0 0xf5000000 0x0 0x2000000>; + num-lanes = <1>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = <0x0 0 0 1 &gic 0 0 0 282 4>, + <0x0 0 0 2 &gic 0 0 0 283 4>, + <0x0 0 0 3 &gic 0 0 0 284 4>, + <0x0 0 0 4 &gic 0 0 0 285 4>; + clocks = <&crg_ctrl HI3660_PCIEPHY_REF>, + <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>, + <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>, + <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>, + <&crg_ctrl HI3660_ACLK_GATE_PCIE>; + clock-names = "pcie_phy_ref", "pcie_aux", + "pcie_apb_phy", "pcie_apb_sys", "pcie_aclk"; + reset-gpios = <&gpio11 1 0 >; + }; diff --git a/Documentation/devicetree/bindings/pci/layerscape-pci.txt b/Documentation/devicetree/bindings/pci/layerscape-pci.txt new file mode 100644 index 000000000..66df1e81e --- /dev/null +++ b/Documentation/devicetree/bindings/pci/layerscape-pci.txt @@ -0,0 +1,60 @@ +Freescale Layerscape PCIe controller + +This PCIe host controller is based on the Synopsys DesignWare PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +This controller derives its clocks from the Reset Configuration Word (RCW) +which is used to describe the PLL settings at the time of chip-reset. + +Also as per the available Reference Manuals, there is no specific 'version' +register available in the Freescale PCIe controller register set, +which can allow determining the underlying DesignWare PCIe controller version +information. + +Required properties: +- compatible: should contain the platform identifier such as: + "fsl,ls1021a-pcie", "snps,dw-pcie" + "fsl,ls2080a-pcie", "fsl,ls2085a-pcie", "snps,dw-pcie" + "fsl,ls2088a-pcie" + "fsl,ls1088a-pcie" + "fsl,ls1046a-pcie" + "fsl,ls1012a-pcie" +- reg: base addresses and lengths of the PCIe controller register blocks. +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + "intr": The interrupt that is asserted for controller interrupts +- fsl,pcie-scfg: Must include two entries. + The first entry must be a link to the SCFG device node + The second entry must be '0' or '1' based on physical PCIe controller index. + This is used to get SCFG PEXN registers +- dma-coherent: Indicates that the hardware IP block can ensure the coherency + of the data transferred from/to the IP block. This can avoid the software + cache flush/invalid actions, and improve the performance significantly. + +Example: + + pcie@3400000 { + compatible = "fsl,ls1021a-pcie", "snps,dw-pcie"; + reg = <0x00 0x03400000 0x0 0x00010000 /* controller registers */ + 0x40 0x00000000 0x0 0x00002000>; /* configuration space */ + reg-names = "regs", "config"; + interrupts = <GIC_SPI 177 IRQ_TYPE_LEVEL_HIGH>; /* controller interrupt */ + interrupt-names = "intr"; + fsl,pcie-scfg = <&scfg 0>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + dma-coherent; + num-lanes = <4>; + bus-range = <0x0 0xff>; + ranges = <0x81000000 0x0 0x00000000 0x40 0x00010000 0x0 0x00010000 /* downstream I/O */ + 0xc2000000 0x0 0x20000000 0x40 0x20000000 0x0 0x20000000 /* prefetchable memory */ + 0x82000000 0x0 0x40000000 0x40 0x40000000 0x0 0x40000000>; /* non-prefetchable memory */ + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0000 0 0 1 &gic GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 2 &gic GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 3 &gic GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>, + <0000 0 0 4 &gic GIC_SPI 192 IRQ_TYPE_LEVEL_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/pci/mediatek-pcie.txt b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt new file mode 100644 index 000000000..20227a875 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/mediatek-pcie.txt @@ -0,0 +1,279 @@ +MediaTek Gen2 PCIe controller + +Required properties: +- compatible: Should contain one of the following strings: + "mediatek,mt2701-pcie" + "mediatek,mt2712-pcie" + "mediatek,mt7622-pcie" + "mediatek,mt7623-pcie" +- device_type: Must be "pci" +- reg: Base addresses and lengths of the PCIe subsys and root ports. +- reg-names: Names of the above areas to use during resource lookup. +- #address-cells: Address representation for root ports (must be 3) +- #size-cells: Size representation for root ports (must be 2) +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: + Mandatory entries: + - sys_ckN :transaction layer and data link layer clock + Required entries for MT2701/MT7623: + - free_ck :for reference clock of PCIe subsys + Required entries for MT2712/MT7622: + - ahb_ckN :AHB slave interface operating clock for CSR access and RC + initiated MMIO access + Required entries for MT7622: + - axi_ckN :application layer MMIO channel operating clock + - aux_ckN :pe2_mac_bridge and pe2_mac_core operating clock when + pcie_mac_ck/pcie_pipe_ck is turned off + - obff_ckN :OBFF functional block operating clock + - pipe_ckN :LTSSM and PHY/MAC layer operating clock + where N starting from 0 to one less than the number of root ports. +- phys: List of PHY specifiers (used by generic PHY framework). +- phy-names : Must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the + number of PHYs as specified in *phys* property. +- power-domains: A phandle and power domain specifier pair to the power domain + which is responsible for collapsing and restoring power to the peripheral. +- bus-range: Range of bus numbers associated with this controller. +- ranges: Ranges for the PCI memory and I/O regions. + +Required properties for MT7623/MT2701: +- #interrupt-cells: Size representation for interrupts (must be 1) +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must be "pcie-rst0", "pcie-rst1", "pcie-rstN".. based on the + number of root ports. + +Required properties for MT2712/MT7622: +-interrupts: A list of interrupt outputs of the controller, must have one + entry for each PCIe port + +In addition, the device tree node must have sub-nodes describing each +PCIe port interface, having the following mandatory properties: + +Required properties: +- device_type: Must be "pci" +- reg: Only the first four bytes are used to refer to the correct bus number + and device number. +- #address-cells: Must be 3 +- #size-cells: Must be 2 +- #interrupt-cells: Must be 1 +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- ranges: Sub-ranges distributed from the PCIe controller node. An empty + property is sufficient. +- num-lanes: Number of lanes to use for this port. + +Examples for MT7623: + + hifsys: syscon@1a000000 { + compatible = "mediatek,mt7623-hifsys", + "mediatek,mt2701-hifsys", + "syscon"; + reg = <0 0x1a000000 0 0x1000>; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + pcie: pcie@1a140000 { + compatible = "mediatek,mt7623-pcie"; + device_type = "pci"; + reg = <0 0x1a140000 0 0x1000>, /* PCIe shared registers */ + <0 0x1a142000 0 0x1000>, /* Port0 registers */ + <0 0x1a143000 0 0x1000>, /* Port1 registers */ + <0 0x1a144000 0 0x1000>; /* Port2 registers */ + reg-names = "subsys", "port0", "port1", "port2"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0xf800 0 0 0>; + interrupt-map = <0x0000 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>, + <0x0800 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>, + <0x1000 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_ETHIF_SEL>, + <&hifsys CLK_HIFSYS_PCIE0>, + <&hifsys CLK_HIFSYS_PCIE1>, + <&hifsys CLK_HIFSYS_PCIE2>; + clock-names = "free_ck", "sys_ck0", "sys_ck1", "sys_ck2"; + resets = <&hifsys MT2701_HIFSYS_PCIE0_RST>, + <&hifsys MT2701_HIFSYS_PCIE1_RST>, + <&hifsys MT2701_HIFSYS_PCIE2_RST>; + reset-names = "pcie-rst0", "pcie-rst1", "pcie-rst2"; + phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>, + <&pcie2_phy PHY_TYPE_PCIE>; + phy-names = "pcie-phy0", "pcie-phy1", "pcie-phy2"; + power-domains = <&scpsys MT2701_POWER_DOMAIN_HIF>; + bus-range = <0x00 0xff>; + ranges = <0x81000000 0 0x1a160000 0 0x1a160000 0 0x00010000 /* I/O space */ + 0x83000000 0 0x60000000 0 0x60000000 0 0x10000000>; /* memory space */ + + pcie@0,0 { + reg = <0x0000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &sysirq GIC_SPI 193 IRQ_TYPE_LEVEL_LOW>; + ranges; + num-lanes = <1>; + }; + + pcie@1,0 { + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &sysirq GIC_SPI 194 IRQ_TYPE_LEVEL_LOW>; + ranges; + num-lanes = <1>; + }; + + pcie@2,0 { + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &sysirq GIC_SPI 195 IRQ_TYPE_LEVEL_LOW>; + ranges; + num-lanes = <1>; + }; + }; + +Examples for MT2712: + + pcie: pcie@11700000 { + compatible = "mediatek,mt2712-pcie"; + device_type = "pci"; + reg = <0 0x11700000 0 0x1000>, + <0 0x112ff000 0 0x1000>; + reg-names = "port0", "port1"; + #address-cells = <3>; + #size-cells = <2>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&topckgen CLK_TOP_PE2_MAC_P0_SEL>, + <&topckgen CLK_TOP_PE2_MAC_P1_SEL>, + <&pericfg CLK_PERI_PCIE0>, + <&pericfg CLK_PERI_PCIE1>; + clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1"; + phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; + phy-names = "pcie-phy0", "pcie-phy1"; + bus-range = <0x00 0xff>; + ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; + + pcie0: pcie@0,0 { + reg = <0x0000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + num-lanes = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc0 0>, + <0 0 0 2 &pcie_intc0 1>, + <0 0 0 3 &pcie_intc0 2>, + <0 0 0 4 &pcie_intc0 3>; + pcie_intc0: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + + pcie1: pcie@1,0 { + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + num-lanes = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc1 0>, + <0 0 0 2 &pcie_intc1 1>, + <0 0 0 3 &pcie_intc1 2>, + <0 0 0 4 &pcie_intc1 3>; + pcie_intc1: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + }; + +Examples for MT7622: + + pcie: pcie@1a140000 { + compatible = "mediatek,mt7622-pcie"; + device_type = "pci"; + reg = <0 0x1a140000 0 0x1000>, + <0 0x1a143000 0 0x1000>, + <0 0x1a145000 0 0x1000>; + reg-names = "subsys", "port0", "port1"; + #address-cells = <3>; + #size-cells = <2>; + interrupts = <GIC_SPI 228 IRQ_TYPE_LEVEL_LOW>, + <GIC_SPI 229 IRQ_TYPE_LEVEL_LOW>; + clocks = <&pciesys CLK_PCIE_P0_MAC_EN>, + <&pciesys CLK_PCIE_P1_MAC_EN>, + <&pciesys CLK_PCIE_P0_AHB_EN>, + <&pciesys CLK_PCIE_P1_AHB_EN>, + <&pciesys CLK_PCIE_P0_AUX_EN>, + <&pciesys CLK_PCIE_P1_AUX_EN>, + <&pciesys CLK_PCIE_P0_AXI_EN>, + <&pciesys CLK_PCIE_P1_AXI_EN>, + <&pciesys CLK_PCIE_P0_OBFF_EN>, + <&pciesys CLK_PCIE_P1_OBFF_EN>, + <&pciesys CLK_PCIE_P0_PIPE_EN>, + <&pciesys CLK_PCIE_P1_PIPE_EN>; + clock-names = "sys_ck0", "sys_ck1", "ahb_ck0", "ahb_ck1", + "aux_ck0", "aux_ck1", "axi_ck0", "axi_ck1", + "obff_ck0", "obff_ck1", "pipe_ck0", "pipe_ck1"; + phys = <&pcie0_phy PHY_TYPE_PCIE>, <&pcie1_phy PHY_TYPE_PCIE>; + phy-names = "pcie-phy0", "pcie-phy1"; + power-domains = <&scpsys MT7622_POWER_DOMAIN_HIF0>; + bus-range = <0x00 0xff>; + ranges = <0x82000000 0 0x20000000 0x0 0x20000000 0 0x10000000>; + + pcie0: pcie@0,0 { + reg = <0x0000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + num-lanes = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc0 0>, + <0 0 0 2 &pcie_intc0 1>, + <0 0 0 3 &pcie_intc0 2>, + <0 0 0 4 &pcie_intc0 3>; + pcie_intc0: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + + pcie1: pcie@1,0 { + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges; + num-lanes = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc1 0>, + <0 0 0 2 &pcie_intc1 1>, + <0 0 0 3 &pcie_intc1 2>, + <0 0 0 4 &pcie_intc1 3>; + pcie_intc1: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt b/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt new file mode 100644 index 000000000..a618d4787 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/mobiveil-pcie.txt @@ -0,0 +1,70 @@ +* Mobiveil AXI PCIe Root Port Bridge DT description + +Mobiveil's GPEX 4.0 is a PCIe Gen4 root port bridge IP. This configurable IP +has up to 8 outbound and inbound windows for the address translation. + +Required properties: +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- compatible: Should contain "mbvl,gpex40-pcie" +- reg: Should contain PCIe registers location and length + "config_axi_slave": PCIe controller registers + "csr_axi_slave" : Bridge config registers + "gpio_slave" : GPIO registers to control slot power + "apb_csr" : MSI registers + +- device_type: must be "pci" +- apio-wins : number of requested apio outbound windows + default 2 outbound windows are configured - + 1. Config window + 2. Memory window +- ppio-wins : number of requested ppio inbound windows + default 1 inbound memory window is configured. +- bus-range: PCI bus numbers covered +- interrupt-controller: identifies the node as an interrupt controller +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- interrupts: The interrupt line of the PCIe controller + last cell of this field is set to 4 to + denote it as IRQ_TYPE_LEVEL_HIGH type interrupt. +- interrupt-map-mask, + interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. +- ranges: ranges for the PCI memory regions (I/O space region is not + supported by hardware) + Please refer to the standard PCI bus binding document for a more + detailed explanation + + +Example: +++++++++ + pcie0: pcie@a0000000 { + #address-cells = <3>; + #size-cells = <2>; + compatible = "mbvl,gpex40-pcie"; + reg = <0xa0000000 0x00001000>, + <0xb0000000 0x00010000>, + <0xff000000 0x00200000>, + <0xb0010000 0x00001000>; + reg-names = "config_axi_slave", + "csr_axi_slave", + "gpio_slave", + "apb_csr"; + device_type = "pci"; + apio-wins = <2>; + ppio-wins = <1>; + bus-range = <0x00000000 0x000000ff>; + interrupt-controller; + interrupt-parent = <&gic>; + #interrupt-cells = <1>; + interrupts = < 0 89 4 >; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 0 &pci_express 0>, + <0 0 0 1 &pci_express 1>, + <0 0 0 2 &pci_express 2>, + <0 0 0 3 &pci_express 3>; + ranges = < 0x83000000 0 0x00000000 0xa8000000 0 0x8000000>; + + }; diff --git a/Documentation/devicetree/bindings/pci/mvebu-pci.txt b/Documentation/devicetree/bindings/pci/mvebu-pci.txt new file mode 100644 index 000000000..6173af688 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/mvebu-pci.txt @@ -0,0 +1,294 @@ +* Marvell EBU PCIe interfaces + +Mandatory properties: + +- compatible: one of the following values: + marvell,armada-370-pcie + marvell,armada-xp-pcie + marvell,dove-pcie + marvell,kirkwood-pcie +- #address-cells, set to <3> +- #size-cells, set to <2> +- #interrupt-cells, set to <1> +- bus-range: PCI bus numbers covered +- device_type, set to "pci" +- ranges: ranges describing the MMIO registers to control the PCIe + interfaces, and ranges describing the MBus windows needed to access + the memory and I/O regions of each PCIe interface. +- msi-parent: Link to the hardware entity that serves as the Message + Signaled Interrupt controller for this PCI controller. + +The ranges describing the MMIO registers have the following layout: + + 0x82000000 0 r MBUS_ID(0xf0, 0x01) r 0 s + +where: + + * r is a 32-bits value that gives the offset of the MMIO + registers of this PCIe interface, from the base of the internal + registers. + + * s is a 32-bits value that give the size of this MMIO + registers area. This range entry translates the '0x82000000 0 r' PCI + address into the 'MBUS_ID(0xf0, 0x01) r' CPU address, which is part + of the internal register window (as identified by MBUS_ID(0xf0, + 0x01)). + +The ranges describing the MBus windows have the following layout: + + 0x8t000000 s 0 MBUS_ID(w, a) 0 1 0 + +where: + + * t is the type of the MBus window (as defined by the standard PCI DT + bindings), 1 for I/O and 2 for memory. + + * s is the PCI slot that corresponds to this PCIe interface + + * w is the 'target ID' value for the MBus window + + * a the 'attribute' value for the MBus window. + +Since the location and size of the different MBus windows is not fixed in +hardware, and only determined in runtime, those ranges cover the full first +4 GB of the physical address space, and do not translate into a valid CPU +address. + +In addition, the device tree node must have sub-nodes describing each +PCIe interface, having the following mandatory properties: + +- reg: used only for interrupt mapping, so only the first four bytes + are used to refer to the correct bus number and device number. +- assigned-addresses: reference to the MMIO registers used to control + this PCIe interface. +- clocks: the clock associated to this PCIe interface +- marvell,pcie-port: the physical PCIe port number +- status: either "disabled" or "okay" +- device_type, set to "pci" +- #address-cells, set to <3> +- #size-cells, set to <2> +- #interrupt-cells, set to <1> +- ranges, translating the MBus windows ranges of the parent node into + standard PCI addresses. +- interrupt-map-mask and interrupt-map, standard PCI properties to + define the mapping of the PCIe interface to interrupt numbers. + +and the following optional properties: +- marvell,pcie-lane: the physical PCIe lane number, for ports having + multiple lanes. If this property is not found, we assume that the + value is 0. +- reset-gpios: optional GPIO to PERST# +- reset-delay-us: delay in us to wait after reset de-assertion, if not + specified will default to 100ms, as required by the PCIe specification. + +Example: + +pcie-controller { + compatible = "marvell,armada-xp-pcie"; + device_type = "pci"; + + #address-cells = <3>; + #size-cells = <2>; + + bus-range = <0x00 0xff>; + msi-parent = <&mpic>; + + ranges = + <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */ + 0x82000000 0 0x42000 MBUS_ID(0xf0, 0x01) 0x42000 0 0x00002000 /* Port 2.0 registers */ + 0x82000000 0 0x44000 MBUS_ID(0xf0, 0x01) 0x44000 0 0x00002000 /* Port 0.1 registers */ + 0x82000000 0 0x48000 MBUS_ID(0xf0, 0x01) 0x48000 0 0x00002000 /* Port 0.2 registers */ + 0x82000000 0 0x4c000 MBUS_ID(0xf0, 0x01) 0x4c000 0 0x00002000 /* Port 0.3 registers */ + 0x82000000 0 0x80000 MBUS_ID(0xf0, 0x01) 0x80000 0 0x00002000 /* Port 1.0 registers */ + 0x82000000 0 0x82000 MBUS_ID(0xf0, 0x01) 0x82000 0 0x00002000 /* Port 3.0 registers */ + 0x82000000 0 0x84000 MBUS_ID(0xf0, 0x01) 0x84000 0 0x00002000 /* Port 1.1 registers */ + 0x82000000 0 0x88000 MBUS_ID(0xf0, 0x01) 0x88000 0 0x00002000 /* Port 1.2 registers */ + 0x82000000 0 0x8c000 MBUS_ID(0xf0, 0x01) 0x8c000 0 0x00002000 /* Port 1.3 registers */ + 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */ + 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */ + 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */ + 0x81000000 0x2 0 MBUS_ID(0x04, 0xd0) 0 1 0 /* Port 0.1 IO */ + 0x82000000 0x3 0 MBUS_ID(0x04, 0xb8) 0 1 0 /* Port 0.2 MEM */ + 0x81000000 0x3 0 MBUS_ID(0x04, 0xb0) 0 1 0 /* Port 0.2 IO */ + 0x82000000 0x4 0 MBUS_ID(0x04, 0x78) 0 1 0 /* Port 0.3 MEM */ + 0x81000000 0x4 0 MBUS_ID(0x04, 0x70) 0 1 0 /* Port 0.3 IO */ + + 0x82000000 0x5 0 MBUS_ID(0x08, 0xe8) 0 1 0 /* Port 1.0 MEM */ + 0x81000000 0x5 0 MBUS_ID(0x08, 0xe0) 0 1 0 /* Port 1.0 IO */ + 0x82000000 0x6 0 MBUS_ID(0x08, 0xd8) 0 1 0 /* Port 1.1 MEM */ + 0x81000000 0x6 0 MBUS_ID(0x08, 0xd0) 0 1 0 /* Port 1.1 IO */ + 0x82000000 0x7 0 MBUS_ID(0x08, 0xb8) 0 1 0 /* Port 1.2 MEM */ + 0x81000000 0x7 0 MBUS_ID(0x08, 0xb0) 0 1 0 /* Port 1.2 IO */ + 0x82000000 0x8 0 MBUS_ID(0x08, 0x78) 0 1 0 /* Port 1.3 MEM */ + 0x81000000 0x8 0 MBUS_ID(0x08, 0x70) 0 1 0 /* Port 1.3 IO */ + + 0x82000000 0x9 0 MBUS_ID(0x04, 0xf8) 0 1 0 /* Port 2.0 MEM */ + 0x81000000 0x9 0 MBUS_ID(0x04, 0xf0) 0 1 0 /* Port 2.0 IO */ + + 0x82000000 0xa 0 MBUS_ID(0x08, 0xf8) 0 1 0 /* Port 3.0 MEM */ + 0x81000000 0xa 0 MBUS_ID(0x08, 0xf0) 0 1 0 /* Port 3.0 IO */>; + + pcie@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>; + reg = <0x0800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0 + 0x81000000 0 0 0x81000000 0x1 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 58>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <0>; + /* low-active PERST# reset on GPIO 25 */ + reset-gpios = <&gpio0 25 1>; + /* wait 20ms for device settle after reset deassertion */ + reset-delay-us = <20000>; + clocks = <&gateclk 5>; + }; + + pcie@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x44000 0 0x2000>; + reg = <0x1000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x2 0 1 0 + 0x81000000 0 0 0x81000000 0x2 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 59>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 6>; + }; + + pcie@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x48000 0 0x2000>; + reg = <0x1800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x3 0 1 0 + 0x81000000 0 0 0x81000000 0x3 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 60>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 7>; + }; + + pcie@4,0 { + device_type = "pci"; + assigned-addresses = <0x82002000 0 0x4c000 0 0x2000>; + reg = <0x2000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x4 0 1 0 + 0x81000000 0 0 0x81000000 0x4 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 61>; + marvell,pcie-port = <0>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 8>; + }; + + pcie@5,0 { + device_type = "pci"; + assigned-addresses = <0x82002800 0 0x80000 0 0x2000>; + reg = <0x2800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x5 0 1 0 + 0x81000000 0 0 0x81000000 0x5 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 62>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 9>; + }; + + pcie@6,0 { + device_type = "pci"; + assigned-addresses = <0x82003000 0 0x84000 0 0x2000>; + reg = <0x3000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x6 0 1 0 + 0x81000000 0 0 0x81000000 0x6 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 63>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <1>; + clocks = <&gateclk 10>; + }; + + pcie@7,0 { + device_type = "pci"; + assigned-addresses = <0x82003800 0 0x88000 0 0x2000>; + reg = <0x3800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x7 0 1 0 + 0x81000000 0 0 0x81000000 0x7 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 64>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <2>; + clocks = <&gateclk 11>; + }; + + pcie@8,0 { + device_type = "pci"; + assigned-addresses = <0x82004000 0 0x8c000 0 0x2000>; + reg = <0x4000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x8 0 1 0 + 0x81000000 0 0 0x81000000 0x8 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 65>; + marvell,pcie-port = <1>; + marvell,pcie-lane = <3>; + clocks = <&gateclk 12>; + }; + + pcie@9,0 { + device_type = "pci"; + assigned-addresses = <0x82004800 0 0x42000 0 0x2000>; + reg = <0x4800 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0x9 0 1 0 + 0x81000000 0 0 0x81000000 0x9 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 99>; + marvell,pcie-port = <2>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 26>; + }; + + pcie@a,0 { + device_type = "pci"; + assigned-addresses = <0x82005000 0 0x82000 0 0x2000>; + reg = <0x5000 0 0 0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + ranges = <0x82000000 0 0 0x82000000 0xa 0 1 0 + 0x81000000 0 0 0x81000000 0xa 0 1 0>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &mpic 103>; + marvell,pcie-port = <3>; + marvell,pcie-lane = <0>; + clocks = <&gateclk 27>; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt new file mode 100644 index 000000000..145a4f041 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt @@ -0,0 +1,674 @@ +NVIDIA Tegra PCIe controller + +Required properties: +- compatible: Must be: + - "nvidia,tegra20-pcie": for Tegra20 + - "nvidia,tegra30-pcie": for Tegra30 + - "nvidia,tegra124-pcie": for Tegra124 and Tegra132 + - "nvidia,tegra210-pcie": for Tegra210 + - "nvidia,tegra186-pcie": for Tegra186 +- power-domains: To ungate power partition by BPMP powergate driver. Must + contain BPMP phandle and PCIe power partition ID. This is required only + for Tegra186. +- device_type: Must be "pci" +- reg: A list of physical base address and length for each set of controller + registers. Must contain an entry for each entry in the reg-names property. +- reg-names: Must include the following entries: + "pads": PADS registers + "afi": AFI registers + "cs": configuration space region +- interrupts: A list of interrupt outputs of the controller. Must contain an + entry for each entry in the interrupt-names property. +- interrupt-names: Must include the following entries: + "intr": The Tegra interrupt that is asserted for controller interrupts + "msi": The Tegra interrupt that is asserted when an MSI is received +- bus-range: Range of bus numbers associated with this controller +- #address-cells: Address representation for root ports (must be 3) + - cell 0 specifies the bus and device numbers of the root port: + [23:16]: bus number + [15:11]: device number + - cell 1 denotes the upper 32 address bits and should be 0 + - cell 2 contains the lower 32 address bits and is used to translate to the + CPU address space +- #size-cells: Size representation for root ports (must be 2) +- ranges: Describes the translation of addresses for root ports and standard + PCI regions. The entries must be 6 cells each, where the first three cells + correspond to the address as described for the #address-cells property + above, the fourth cell is the physical CPU address to translate to and the + fifth and six cells are as described for the #size-cells property above. + - The first two entries are expected to translate the addresses for the root + port registers, which are referenced by the assigned-addresses property of + the root port nodes (see below). + - The remaining entries setup the mapping for the standard I/O, memory and + prefetchable PCI regions. The first cell determines the type of region + that is setup: + - 0x81000000: I/O memory region + - 0x82000000: non-prefetchable memory region + - 0xc2000000: prefetchable memory region + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- #interrupt-cells: Size representation for interrupts (must be 1) +- interrupt-map-mask and interrupt-map: Standard PCI IRQ mapping properties + Please refer to the standard PCI bus binding document for a more detailed + explanation. +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - pex + - afi + - pll_e + - cml (not required for Tegra20) +- resets: Must contain an entry for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following entries: + - pex + - afi + - pcie_x + +Required properties on Tegra124 and later (deprecated): +- phys: Must contain an entry for each entry in phy-names. +- phy-names: Must include the following entries: + - pcie + +These properties are deprecated in favour of per-lane PHYs define in each of +the root ports (see below). + +Power supplies for Tegra20: +- avdd-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. +- vdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. +- avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. +- avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must + supply 1.05 V. +- vddio-pex-clk-supply: Power supply for PCIe clock. Must supply 3.3 V. + +Power supplies for Tegra30: +- Required: + - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - avdd-plle-supply: Power supply for PLLE, which is shared with SATA. Must + supply 1.05 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 1.8 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 3.3 V. +- Optional: + - If lanes 0 to 3 are used: + - avdd-pexa-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - vdd-pexa-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - If lanes 4 or 5 are used: + - avdd-pexb-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - vdd-pexb-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + +Power supplies for Tegra124: +- Required: + - avddio-pex-supply: Power supply for analog PCIe logic. Must supply 1.05 V. + - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - avdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 3.3 V. + - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3). + Must supply 3.3 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 2.8-3.3 V. + - avdd-pll-erefe-supply: Power supply for PLLE (shared with USB3). Must + supply 1.05 V. + +Power supplies for Tegra210: +- Required: + - avdd-pll-uerefe-supply: Power supply for PLLE (shared with USB3). Must + supply 1.05 V. + - hvddio-pex-supply: High-voltage supply for PCIe I/O and PCIe output + clocks. Must supply 1.8 V. + - dvddio-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - dvdd-pex-pll-supply: Power supply for dedicated (internal) PCIe PLL. Must + supply 1.05 V. + - hvdd-pex-pll-e-supply: High-voltage supply for PLLE (shared with USB3). + Must supply 3.3 V. + - vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must + supply 1.8 V. + +Power supplies for Tegra186: +- Required: + - dvdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V. + - hvdd-pex-pll-supply: High-voltage supply for PLLE (shared with USB3). Must + supply 1.8 V. + - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks. + Must supply 1.8 V. + - vddio-pexctl-aud-supply: Power supply for PCIe side band signals. Must + supply 1.8 V. + +Root ports are defined as subnodes of the PCIe controller node. + +Required properties: +- device_type: Must be "pci" +- assigned-addresses: Address and size of the port configuration registers +- reg: PCI bus address of the root port +- #address-cells: Must be 3 +- #size-cells: Must be 2 +- ranges: Sub-ranges distributed from the PCIe controller node. An empty + property is sufficient. +- nvidia,num-lanes: Number of lanes to use for this port. Valid combinations + are: + - Root port 0 uses 4 lanes, root port 1 is unused. + - Both root ports use 2 lanes. + +Required properties for Tegra124 and later: +- phys: Must contain an phandle to a PHY for each entry in phy-names. +- phy-names: Must include an entry for each active lane. Note that the number + of entries does not have to (though usually will) be equal to the specified + number of lanes in the nvidia,num-lanes property. Entries are of the form + "pcie-N": where N ranges from 0 to the value specified in nvidia,num-lanes. + +Examples: +========= + +Tegra20: +-------- + +SoC DTSI: + + pcie-controller@80003000 { + compatible = "nvidia,tegra20-pcie"; + device_type = "pci"; + reg = <0x80003000 0x00000800 /* PADS registers */ + 0x80003800 0x00000200 /* AFI registers */ + 0x90000000 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <0 98 0x04 /* controller interrupt */ + 0 99 0x04>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x80000000 0x80000000 0 0x00001000 /* port 0 registers */ + 0x82000000 0 0x80001000 0x80001000 0 0x00001000 /* port 1 registers */ + 0x81000000 0 0 0x82000000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0xa0000000 0xa0000000 0 0x10000000 /* non-prefetchable memory */ + 0xc2000000 0 0xb0000000 0xb0000000 0 0x10000000>; /* prefetchable memory */ + + clocks = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 118>; + clock-names = "pex", "afi", "pll_e"; + resets = <&tegra_car 70>, <&tegra_car 72>, <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x80000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x80001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + + ranges; + + nvidia,num-lanes = <2>; + }; + }; + +Board DTS: + + pcie-controller@80003000 { + status = "okay"; + + vdd-supply = <&pci_vdd_reg>; + pex-clk-supply = <&pci_clk_reg>; + + /* root port 00:01.0 */ + pci@1,0 { + status = "okay"; + + /* bridge 01:00.0 (optional) */ + pci@0,0 { + reg = <0x010000 0 0 0 0>; + + #address-cells = <3>; + #size-cells = <2>; + + device_type = "pci"; + + /* endpoint 02:00.0 */ + pci@0,0 { + reg = <0x020000 0 0 0 0>; + }; + }; + }; + }; + +Note that devices on the PCI bus are dynamically discovered using PCI's bus +enumeration and therefore don't need corresponding device nodes in DT. However +if a device on the PCI bus provides a non-probeable bus such as I2C or SPI, +device nodes need to be added in order to allow the bus' children to be +instantiated at the proper location in the operating system's device tree (as +illustrated by the optional nodes in the example above). + +Tegra30: +-------- + +SoC DTSI: + + pcie-controller@3000 { + compatible = "nvidia,tegra30-pcie"; + device_type = "pci"; + reg = <0x00003000 0x00000800 /* PADS registers */ + 0x00003800 0x00000200 /* AFI registers */ + 0x10000000 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH /* controller interrupt */ + GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &intc GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x00000000 0x00000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x00001000 0x00001000 0 0x00001000 /* port 1 configuration space */ + 0x82000000 0 0x00004000 0x00004000 0 0x00001000 /* port 2 configuration space */ + 0x81000000 0 0 0x02000000 0 0x00010000 /* downstream I/O */ + 0x82000000 0 0x20000000 0x20000000 0 0x08000000 /* non-prefetchable memory */ + 0xc2000000 0 0x28000000 0x28000000 0 0x18000000>; /* prefetchable memory */ + + clocks = <&tegra_car TEGRA30_CLK_PCIE>, + <&tegra_car TEGRA30_CLK_AFI>, + <&tegra_car TEGRA30_CLK_PLL_E>, + <&tegra_car TEGRA30_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x00000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x00001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x00004000 0 0x1000>; + reg = <0x001800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + }; + +Board DTS: + + pcie-controller@3000 { + status = "okay"; + + avdd-pexa-supply = <&ldo1_reg>; + vdd-pexa-supply = <&ldo1_reg>; + avdd-pexb-supply = <&ldo1_reg>; + vdd-pexb-supply = <&ldo1_reg>; + avdd-pex-pll-supply = <&ldo1_reg>; + avdd-plle-supply = <&ldo1_reg>; + vddio-pex-ctl-supply = <&sys_3v3_reg>; + hvdd-pex-supply = <&sys_3v3_pexs_reg>; + + pci@1,0 { + status = "okay"; + }; + + pci@3,0 { + status = "okay"; + }; + }; + +Tegra124: +--------- + +SoC DTSI: + + pcie-controller@1003000 { + compatible = "nvidia,tegra124-pcie"; + device_type = "pci"; + reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ + 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ + 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ + + clocks = <&tegra_car TEGRA124_CLK_PCIE>, + <&tegra_car TEGRA124_CLK_AFI>, + <&tegra_car TEGRA124_CLK_PLL_E>, + <&tegra_car TEGRA124_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie-controller@1003000 { + status = "okay"; + + avddio-pex-supply = <&vdd_1v05_run>; + dvddio-pex-supply = <&vdd_1v05_run>; + avdd-pex-pll-supply = <&vdd_1v05_run>; + hvdd-pex-supply = <&vdd_3v3_lp0>; + hvdd-pex-pll-e-supply = <&vdd_3v3_lp0>; + vddio-pex-ctl-supply = <&vdd_3v3_lp0>; + avdd-pll-erefe-supply = <&avdd_1v05_run>; + + /* Mini PCIe */ + pci@1,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; + phy-names = "pcie-0"; + status = "okay"; + }; + + /* Gigabit Ethernet */ + pci@2,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>; + phy-names = "pcie-0"; + status = "okay"; + }; + }; + +Tegra210: +--------- + +SoC DTSI: + + pcie-controller@1003000 { + compatible = "nvidia,tegra210-pcie"; + device_type = "pci"; + reg = <0x0 0x01003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x01003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x02000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x01000000 0x0 0x01000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x01001000 0x0 0x01001000 0 0x00001000 /* port 1 configuration space */ + 0x81000000 0 0x0 0x0 0x12000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x13000000 0x0 0x13000000 0 0x0d000000 /* non-prefetchable memory (208 MiB) */ + 0xc2000000 0 0x20000000 0x0 0x20000000 0 0x20000000>; /* prefetchable memory (512 MiB) */ + + clocks = <&tegra_car TEGRA210_CLK_PCIE>, + <&tegra_car TEGRA210_CLK_AFI>, + <&tegra_car TEGRA210_CLK_PLL_E>, + <&tegra_car TEGRA210_CLK_CML0>; + clock-names = "pex", "afi", "pll_e", "cml"; + resets = <&tegra_car 70>, + <&tegra_car 72>, + <&tegra_car 74>; + reset-names = "pex", "afi", "pcie_x"; + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x01000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <4>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x01001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie-controller@1003000 { + status = "okay"; + + avdd-pll-uerefe-supply = <&avdd_1v05_pll>; + hvddio-pex-supply = <&vdd_1v8>; + dvddio-pex-supply = <&vdd_pex_1v05>; + dvdd-pex-pll-supply = <&vdd_pex_1v05>; + hvdd-pex-pll-e-supply = <&vdd_1v8>; + vddio-pex-ctl-supply = <&vdd_1v8>; + + pci@1,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-0}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-1}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-2}>, + <&{/padctl@7009f000/pads/pcie/lanes/pcie-3}>; + phy-names = "pcie-0", "pcie-1", "pcie-2", "pcie-3"; + status = "okay"; + }; + + pci@2,0 { + phys = <&{/padctl@7009f000/pads/pcie/lanes/pcie-4}>; + phy-names = "pcie-0"; + status = "okay"; + }; + }; + +Tegra186: +--------- + +SoC DTSI: + + pcie@10003000 { + compatible = "nvidia,tegra186-pcie"; + power-domains = <&bpmp TEGRA186_POWER_DOMAIN_PCX>; + device_type = "pci"; + reg = <0x0 0x10003000 0x0 0x00000800 /* PADS registers */ + 0x0 0x10003800 0x0 0x00000800 /* AFI registers */ + 0x0 0x40000000 0x0 0x10000000>; /* configuration space */ + reg-names = "pads", "afi", "cs"; + + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */ + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */ + interrupt-names = "intr", "msi"; + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; + + bus-range = <0x00 0xff>; + #address-cells = <3>; + #size-cells = <2>; + + ranges = <0x82000000 0 0x10000000 0x0 0x10000000 0 0x00001000 /* port 0 configuration space */ + 0x82000000 0 0x10001000 0x0 0x10001000 0 0x00001000 /* port 1 configuration space */ + 0x82000000 0 0x10004000 0x0 0x10004000 0 0x00001000 /* port 2 configuration space */ + 0x81000000 0 0x0 0x0 0x50000000 0 0x00010000 /* downstream I/O (64 KiB) */ + 0x82000000 0 0x50100000 0x0 0x50100000 0 0x07F00000 /* non-prefetchable memory (127 MiB) */ + 0xc2000000 0 0x58000000 0x0 0x58000000 0 0x28000000>; /* prefetchable memory (640 MiB) */ + + clocks = <&bpmp TEGRA186_CLK_AFI>, + <&bpmp TEGRA186_CLK_PCIE>, + <&bpmp TEGRA186_CLK_PLLE>; + clock-names = "afi", "pex", "pll_e"; + + resets = <&bpmp TEGRA186_RESET_AFI>, + <&bpmp TEGRA186_RESET_PCIE>, + <&bpmp TEGRA186_RESET_PCIEXCLK>; + reset-names = "afi", "pex", "pcie_x"; + + status = "disabled"; + + pci@1,0 { + device_type = "pci"; + assigned-addresses = <0x82000800 0 0x10000000 0 0x1000>; + reg = <0x000800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <2>; + }; + + pci@2,0 { + device_type = "pci"; + assigned-addresses = <0x82001000 0 0x10001000 0 0x1000>; + reg = <0x001000 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + + pci@3,0 { + device_type = "pci"; + assigned-addresses = <0x82001800 0 0x10004000 0 0x1000>; + reg = <0x001800 0 0 0 0>; + status = "disabled"; + + #address-cells = <3>; + #size-cells = <2>; + ranges; + + nvidia,num-lanes = <1>; + }; + }; + +Board DTS: + + pcie@10003000 { + status = "okay"; + + dvdd-pex-supply = <&vdd_pex>; + hvdd-pex-pll-supply = <&vdd_1v8>; + hvdd-pex-supply = <&vdd_1v8>; + vddio-pexctl-aud-supply = <&vdd_1v8>; + + pci@1,0 { + nvidia,num-lanes = <4>; + status = "okay"; + }; + + pci@2,0 { + nvidia,num-lanes = <0>; + status = "disabled"; + }; + + pci@3,0 { + nvidia,num-lanes = <1>; + status = "disabled"; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-armada8k.txt b/Documentation/devicetree/bindings/pci/pci-armada8k.txt new file mode 100644 index 000000000..9e3fc15e1 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-armada8k.txt @@ -0,0 +1,40 @@ +* Marvell Armada 7K/8K PCIe interface + +This PCIe host controller is based on the Synopsys DesignWare PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "marvell,armada8k-pcie" +- reg: must contain two register regions + - the control register region + - the config space region +- reg-names: + - "ctrl" for the control register region + - "config" for the config space region +- interrupts: Interrupt specifier for the PCIe controler +- clocks: reference to the PCIe controller clocks +- clock-names: mandatory if there is a second clock, in this case the + name must be "core" for the first clock and "reg" for the second + one + +Example: + + pcie@f2600000 { + compatible = "marvell,armada8k-pcie", "snps,dw-pcie"; + reg = <0 0xf2600000 0 0x10000>, <0 0xf6f00000 0 0x80000>; + reg-names = "ctrl", "config"; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + device_type = "pci"; + dma-coherent; + + bus-range = <0 0xff>; + ranges = <0x81000000 0 0xf9000000 0 0xf9000000 0 0x10000 /* downstream I/O */ + 0x82000000 0 0xf6000000 0 0xf6000000 0 0xf00000>; /* non-prefetchable memory */ + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <1>; + clocks = <&cpm_syscon0 1 13>; + }; diff --git a/Documentation/devicetree/bindings/pci/pci-iommu.txt b/Documentation/devicetree/bindings/pci/pci-iommu.txt new file mode 100644 index 000000000..0def586fd --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-iommu.txt @@ -0,0 +1,171 @@ +This document describes the generic device tree binding for describing the +relationship between PCI(e) devices and IOMMU(s). + +Each PCI(e) device under a root complex is uniquely identified by its Requester +ID (AKA RID). A Requester ID is a triplet of a Bus number, Device number, and +Function number. + +For the purpose of this document, when treated as a numeric value, a RID is +formatted such that: + +* Bits [15:8] are the Bus number. +* Bits [7:3] are the Device number. +* Bits [2:0] are the Function number. +* Any other bits required for padding must be zero. + +IOMMUs may distinguish PCI devices through sideband data derived from the +Requester ID. While a given PCI device can only master through one IOMMU, a +root complex may split masters across a set of IOMMUs (e.g. with one IOMMU per +bus). + +The generic 'iommus' property is insufficient to describe this relationship, +and a mechanism is required to map from a PCI device to its IOMMU and sideband +data. + +For generic IOMMU bindings, see +Documentation/devicetree/bindings/iommu/iommu.txt. + + +PCI root complex +================ + +Optional properties +------------------- + +- iommu-map: Maps a Requester ID to an IOMMU and associated IOMMU specifier + data. + + The property is an arbitrary number of tuples of + (rid-base,iommu,iommu-base,length). + + Any RID r in the interval [rid-base, rid-base + length) is associated with + the listed IOMMU, with the IOMMU specifier (r - rid-base + iommu-base). + +- iommu-map-mask: A mask to be applied to each Requester ID prior to being + mapped to an IOMMU specifier per the iommu-map property. + + +Example (1) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + iommu: iommu@a { + reg = <0xa 0x1>; + compatible = "vendor,some-iommu"; + #iommu-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the IOMMU is the RID, + * identity-mapped. + */ + iommu-map = <0x0 &iommu 0x0 0x10000>; + }; +}; + + +Example (2) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + iommu: iommu@a { + reg = <0xa 0x1>; + compatible = "vendor,some-iommu"; + #iommu-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the IOMMU is the RID with the + * function bits masked out. + */ + iommu-map = <0x0 &iommu 0x0 0x10000>; + iommu-map-mask = <0xfff8>; + }; +}; + + +Example (3) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + iommu: iommu@a { + reg = <0xa 0x1>; + compatible = "vendor,some-iommu"; + #iommu-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the IOMMU is the RID, + * but the high bits of the bus number are flipped. + */ + iommu-map = <0x0000 &iommu 0x8000 0x8000>, + <0x8000 &iommu 0x0000 0x8000>; + }; +}; + + +Example (4) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + iommu_a: iommu@a { + reg = <0xa 0x1>; + compatible = "vendor,some-iommu"; + #iommu-cells = <1>; + }; + + iommu_b: iommu@b { + reg = <0xb 0x1>; + compatible = "vendor,some-iommu"; + #iommu-cells = <1>; + }; + + iommu_c: iommu@c { + reg = <0xc 0x1>; + compatible = "vendor,some-iommu"; + #iommu-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * Devices with bus number 0-127 are mastered via IOMMU + * a, with sideband data being RID[14:0]. + * Devices with bus number 128-255 are mastered via + * IOMMU b, with sideband data being RID[14:0]. + * No devices master via IOMMU c. + */ + iommu-map = <0x0000 &iommu_a 0x0000 0x8000>, + <0x8000 &iommu_b 0x0000 0x8000>; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/pci-keystone.txt b/Documentation/devicetree/bindings/pci/pci-keystone.txt new file mode 100644 index 000000000..4dd17de54 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-keystone.txt @@ -0,0 +1,60 @@ +TI Keystone PCIe interface + +Keystone PCI host Controller is based on the Synopsys DesignWare PCI +hardware version 3.65. It shares common functions with the PCIe DesignWare +core driver and inherits common properties defined in +Documentation/devicetree/bindings/pci/designware-pcie.txt + +Please refer to Documentation/devicetree/bindings/pci/designware-pcie.txt +for the details of DesignWare DT bindings. Additional properties are +described here as well as properties that are not applicable. + +Required Properties:- + +compatibility: "ti,keystone-pcie" +reg: index 1 is the base address and length of DW application registers. + index 2 is the base address and length of PCI device ID register. + +pcie_msi_intc : Interrupt controller device node for MSI IRQ chip + interrupt-cells: should be set to 1 + interrupts: GIC interrupt lines connected to PCI MSI interrupt lines + + Example: + pcie_msi_intc: msi-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 31 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>; + }; + +pcie_intc: Interrupt controller device node for Legacy IRQ chip + interrupt-cells: should be set to 1 + + Example: + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #interrupt-cells = <1>; + interrupt-parent = <&gic>; + interrupts = <GIC_SPI 26 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 27 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 28 IRQ_TYPE_EDGE_RISING>, + <GIC_SPI 29 IRQ_TYPE_EDGE_RISING>; + }; + +Optional properties:- + phys: phandle to generic Keystone SerDes PHY for PCI + phy-names: name of the generic Keystone SerDes PHY for PCI + - If boot loader already does PCI link establishment, then phys and + phy-names shouldn't be present. + interrupts: platform interrupt for error interrupts. + +DesignWare DT Properties not applicable for Keystone PCI + +1. pcie_bus clock-names not used. Instead, a phandle to phys is used. diff --git a/Documentation/devicetree/bindings/pci/pci-msi.txt b/Documentation/devicetree/bindings/pci/pci-msi.txt new file mode 100644 index 000000000..9b3cc817d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-msi.txt @@ -0,0 +1,220 @@ +This document describes the generic device tree binding for describing the +relationship between PCI devices and MSI controllers. + +Each PCI device under a root complex is uniquely identified by its Requester ID +(AKA RID). A Requester ID is a triplet of a Bus number, Device number, and +Function number. + +For the purpose of this document, when treated as a numeric value, a RID is +formatted such that: + +* Bits [15:8] are the Bus number. +* Bits [7:3] are the Device number. +* Bits [2:0] are the Function number. +* Any other bits required for padding must be zero. + +MSIs may be distinguished in part through the use of sideband data accompanying +writes. In the case of PCI devices, this sideband data may be derived from the +Requester ID. A mechanism is required to associate a device with both the MSI +controllers it can address, and the sideband data that will be associated with +its writes to those controllers. + +For generic MSI bindings, see +Documentation/devicetree/bindings/interrupt-controller/msi.txt. + + +PCI root complex +================ + +Optional properties +------------------- + +- msi-map: Maps a Requester ID to an MSI controller and associated + msi-specifier data. The property is an arbitrary number of tuples of + (rid-base,msi-controller,msi-base,length), where: + + * rid-base is a single cell describing the first RID matched by the entry. + + * msi-controller is a single phandle to an MSI controller + + * msi-base is an msi-specifier describing the msi-specifier produced for the + first RID matched by the entry. + + * length is a single cell describing how many consecutive RIDs are matched + following the rid-base. + + Any RID r in the interval [rid-base, rid-base + length) is associated with + the listed msi-controller, with the msi-specifier (r - rid-base + msi-base). + +- msi-map-mask: A mask to be applied to each Requester ID prior to being mapped + to an msi-specifier per the msi-map property. + +- msi-parent: Describes the MSI parent of the root complex itself. Where + the root complex and MSI controller do not pass sideband data with MSI + writes, this property may be used to describe the MSI controller(s) + used by PCI devices under the root complex, if defined as such in the + binding for the root complex. + + +Example (1) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, identity-mapped. + */ + msi-map = <0x0 &msi_a 0x0 0x10000>, + }; +}; + + +Example (2) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, masked to only the device and function bits. + */ + msi-map = <0x0 &msi_a 0x0 0x100>, + msi-map-mask = <0xff> + }; +}; + + +Example (3) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, but the high bit of the bus number is + * ignored. + */ + msi-map = <0x0000 &msi 0x0000 0x8000>, + <0x8000 &msi 0x0000 0x8000>; + }; +}; + + +Example (4) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@f { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to the MSI controller is + * the RID, but the high bit of the bus number is + * negated. + */ + msi-map = <0x0000 &msi 0x8000 0x8000>, + <0x8000 &msi 0x0000 0x8000>; + }; +}; + + +Example (5) +=========== + +/ { + #address-cells = <1>; + #size-cells = <1>; + + msi_a: msi-controller@a { + reg = <0xa 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + msi_b: msi-controller@b { + reg = <0xb 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + msi_c: msi-controller@c { + reg = <0xc 0x1>; + compatible = "vendor,some-controller"; + msi-controller; + #msi-cells = <1>; + }; + + pci: pci@c { + reg = <0xf 0x1>; + compatible = "vendor,pcie-root-complex"; + device_type = "pci"; + + /* + * The sideband data provided to MSI controller a is the + * RID, but the high bit of the bus number is negated. + * The sideband data provided to MSI controller b is the + * RID, identity-mapped. + * MSI controller c is not addressable. + */ + msi-map = <0x0000 &msi_a 0x8000 0x08000>, + <0x8000 &msi_a 0x0000 0x08000>, + <0x0000 &msi_b 0x0000 0x10000>; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt new file mode 100644 index 000000000..9fe7e12a7 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-rcar-gen2.txt @@ -0,0 +1,82 @@ +Renesas AHB to PCI bridge +------------------------- + +This is the bridge used internally to connect the USB controllers to the +AHB. There is one bridge instance per USB port connected to the internal +OHCI and EHCI controllers. + +Required properties: +- compatible: "renesas,pci-r8a7743" for the R8A7743 SoC; + "renesas,pci-r8a7745" for the R8A7745 SoC; + "renesas,pci-r8a7790" for the R8A7790 SoC; + "renesas,pci-r8a7791" for the R8A7791 SoC; + "renesas,pci-r8a7793" for the R8A7793 SoC; + "renesas,pci-r8a7794" for the R8A7794 SoC; + "renesas,pci-rcar-gen2" for a generic R-Car Gen2 or + RZ/G1 compatible device. + + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + +- reg: A list of physical regions to access the device: the first is + the operational registers for the OHCI/EHCI controllers and the + second is for the bridge configuration and control registers. +- interrupts: interrupt for the device. +- clocks: The reference to the device clock. +- bus-range: The PCI bus number range; as this is a single bus, the range + should be specified as the same value twice. +- #address-cells: must be 3. +- #size-cells: must be 2. +- #interrupt-cells: must be 1. +- interrupt-map: standard property used to define the mapping of the PCI + interrupts to the GIC interrupts. +- interrupt-map-mask: standard property that helps to define the interrupt + mapping. + +Optional properties: +- dma-ranges: a single range for the inbound memory region. If not supplied, + defaults to 1GiB at 0x40000000. Note there are hardware restrictions on the + allowed combinations of address and size. + +Example SoC configuration: + + pci0: pci@ee090000 { + compatible = "renesas,pci-r8a7790", "renesas,pci-rcar-gen2"; + clocks = <&mstp7_clks R8A7790_CLK_EHCI>; + reg = <0x0 0xee090000 0x0 0xc00>, + <0x0 0xee080000 0x0 0x1100>; + interrupts = <0 108 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + + bus-range = <0 0>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000>; + interrupt-map-mask = <0xff00 0 0 0x7>; + interrupt-map = <0x0000 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x0800 0 0 1 &gic 0 108 IRQ_TYPE_LEVEL_HIGH + 0x1000 0 0 2 &gic 0 108 IRQ_TYPE_LEVEL_HIGH>; + + usb@1,0 { + reg = <0x800 0 0 0 0>; + phys = <&usb0 0>; + phy-names = "usb"; + }; + + usb@2,0 { + reg = <0x1000 0 0 0 0>; + phys = <&usb0 0>; + phy-names = "usb"; + }; + }; + +Example board setup: + +&pci0 { + status = "okay"; + pinctrl-0 = <&usb0_pins>; + pinctrl-names = "default"; +}; diff --git a/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt b/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt new file mode 100644 index 000000000..f478874b7 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-thunder-ecam.txt @@ -0,0 +1,30 @@ +* ThunderX PCI host controller for pass-1.x silicon + +Firmware-initialized PCI host controller to on-chip devices found on +some Cavium ThunderX processors. These devices have ECAM-based config +access, but the BARs are all at fixed addresses. We handle the fixed +addresses by synthesizing Enhanced Allocation (EA) capabilities for +these devices. + +The properties and their meanings are identical to those described in +host-generic-pci.txt except as listed below. + +Properties of the host controller node that differ from +host-generic-pci.txt: + +- compatible : Must be "cavium,pci-host-thunder-ecam" + +Example: + + pcie@84b000000000 { + compatible = "cavium,pci-host-thunder-ecam"; + device_type = "pci"; + msi-parent = <&its>; + msi-map = <0 &its 0x30000 0x10000>; + bus-range = <0 31>; + #size-cells = <2>; + #address-cells = <3>; + #stream-id-cells = <1>; + reg = <0x84b0 0x00000000 0 0x02000000>; /* Configuration space */ + ranges = <0x03000000 0x8180 0x00000000 0x8180 0x00000000 0x80 0x00000000>; /* mem ranges */ + }; diff --git a/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt b/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt new file mode 100644 index 000000000..f131faea3 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci-thunder-pem.txt @@ -0,0 +1,43 @@ +* ThunderX PEM PCIe host controller + +Firmware-initialized PCI host controller found on some Cavium +ThunderX processors. + +The properties and their meanings are identical to those described in +host-generic-pci.txt except as listed below. + +Properties of the host controller node that differ from +host-generic-pci.txt: + +- compatible : Must be "cavium,pci-host-thunder-pem" + +- reg : Two entries: First the configuration space for down + stream devices base address and size, as accessed + from the parent bus. Second, the register bank of + the PEM device PCIe bridge. + +Example: + + pci@87e0,c2000000 { + compatible = "cavium,pci-host-thunder-pem"; + device_type = "pci"; + msi-parent = <&its>; + msi-map = <0 &its 0x10000 0x10000>; + bus-range = <0x8f 0xc7>; + #size-cells = <2>; + #address-cells = <3>; + + reg = <0x8880 0x8f000000 0x0 0x39000000>, /* Configuration space */ + <0x87e0 0xc2000000 0x0 0x00010000>; /* PEM space */ + ranges = <0x01000000 0x00 0x00020000 0x88b0 0x00020000 0x00 0x00010000>, /* I/O */ + <0x03000000 0x00 0x10000000 0x8890 0x10000000 0x0f 0xf0000000>, /* mem64 */ + <0x43000000 0x10 0x00000000 0x88a0 0x00000000 0x10 0x00000000>, /* mem64-pref */ + <0x03000000 0x87e0 0xc2f00000 0x87e0 0xc2000000 0x00 0x00100000>; /* mem64 PEM BAR4 */ + + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &gic0 0 0 0 24 4>, /* INTA */ + <0 0 0 2 &gic0 0 0 0 25 4>, /* INTB */ + <0 0 0 3 &gic0 0 0 0 26 4>, /* INTC */ + <0 0 0 4 &gic0 0 0 0 27 4>; /* INTD */ + }; diff --git a/Documentation/devicetree/bindings/pci/pci.txt b/Documentation/devicetree/bindings/pci/pci.txt new file mode 100644 index 000000000..c77981c5d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/pci.txt @@ -0,0 +1,26 @@ +PCI bus bridges have standardized Device Tree bindings: + +PCI Bus Binding to: IEEE Std 1275-1994 +http://www.devicetree.org/open-firmware/bindings/pci/pci2_1.pdf + +And for the interrupt mapping part: + +Open Firmware Recommended Practice: Interrupt Mapping +http://www.devicetree.org/open-firmware/practice/imap/imap0_9d.pdf + +Additionally to the properties specified in the above standards a host bridge +driver implementation may support the following properties: + +- linux,pci-domain: + If present this property assigns a fixed PCI domain number to a host bridge, + otherwise an unstable (across boots) unique number will be assigned. + It is required to either not set this property at all or set it for all + host bridges in the system, otherwise potentially conflicting domain numbers + may be assigned to root buses behind different host bridges. The domain + number for each host bridge in the system must be unique. +- max-link-speed: + If present this property specifies PCI gen for link capability. Host + drivers could add this as a strategy to avoid unnecessary operation for + unsupported link speed, for instance, trying to do training for + unsupported link speed, etc. Must be '4' for gen4, '3' for gen3, '2' + for gen2, and '1' for gen1. Any other values are invalid. diff --git a/Documentation/devicetree/bindings/pci/plda,xpressrich3-axi.txt b/Documentation/devicetree/bindings/pci/plda,xpressrich3-axi.txt new file mode 100644 index 000000000..f3f75bfb4 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/plda,xpressrich3-axi.txt @@ -0,0 +1,12 @@ +* PLDA XpressRICH3-AXI host controller + +The PLDA XpressRICH3-AXI host controller can be configured in a manner that +makes it compliant with the SBSA[1] standard published by ARM Ltd. For those +scenarios, the host-generic-pci.txt bindings apply with the following additions +to the compatible property: + +Required properties: + - compatible: should contain "plda,xpressrich3-axi" to identify the IP used. + + +[1] http://infocenter.arm.com/help/topic/com.arm.doc.den0029a/ diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt new file mode 100644 index 000000000..1fd703bd7 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt @@ -0,0 +1,290 @@ +* Qualcomm PCI express root complex + +- compatible: + Usage: required + Value type: <stringlist> + Definition: Value should contain + - "qcom,pcie-ipq8064" for ipq8064 + - "qcom,pcie-apq8064" for apq8064 + - "qcom,pcie-apq8084" for apq8084 + - "qcom,pcie-msm8996" for msm8996 or apq8096 + - "qcom,pcie-ipq4019" for ipq4019 + - "qcom,pcie-ipq8074" for ipq8074 + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: Register ranges as listed in the reg-names property + +- reg-names: + Usage: required + Value type: <stringlist> + Definition: Must include the following entries + - "parf" Qualcomm specific registers + - "dbi" DesignWare PCIe registers + - "elbi" External local bus interface registers + - "config" PCIe configuration space + +- device_type: + Usage: required + Value type: <string> + Definition: Should be "pci". As specified in designware-pcie.txt + +- #address-cells: + Usage: required + Value type: <u32> + Definition: Should be 3. As specified in designware-pcie.txt + +- #size-cells: + Usage: required + Value type: <u32> + Definition: Should be 2. As specified in designware-pcie.txt + +- ranges: + Usage: required + Value type: <prop-encoded-array> + Definition: As specified in designware-pcie.txt + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: MSI interrupt + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: Should contain "msi" + +- #interrupt-cells: + Usage: required + Value type: <u32> + Definition: Should be 1. As specified in designware-pcie.txt + +- interrupt-map-mask: + Usage: required + Value type: <prop-encoded-array> + Definition: As specified in designware-pcie.txt + +- interrupt-map: + Usage: required + Value type: <prop-encoded-array> + Definition: As specified in designware-pcie.txt + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: List of phandle and clock specifier pairs as listed + in clock-names property + +- clock-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the following entries + - "iface" Configuration AHB clock + +- clock-names: + Usage: required for ipq/apq8064 + Value type: <stringlist> + Definition: Should contain the following entries + - "core" Clocks the pcie hw block + - "phy" Clocks the pcie PHY block +- clock-names: + Usage: required for apq8084/ipq4019 + Value type: <stringlist> + Definition: Should contain the following entries + - "aux" Auxiliary (AUX) clock + - "bus_master" Master AXI clock + - "bus_slave" Slave AXI clock + +- clock-names: + Usage: required for msm8996/apq8096 + Value type: <stringlist> + Definition: Should contain the following entries + - "pipe" Pipe Clock driving internal logic + - "aux" Auxiliary (AUX) clock + - "cfg" Configuration clock + - "bus_master" Master AXI clock + - "bus_slave" Slave AXI clock + +- clock-names: + Usage: required for ipq8074 + Value type: <stringlist> + Definition: Should contain the following entries + - "iface" PCIe to SysNOC BIU clock + - "axi_m" AXI Master clock + - "axi_s" AXI Slave clock + - "ahb" AHB clock + - "aux" Auxiliary clock + +- resets: + Usage: required + Value type: <prop-encoded-array> + Definition: List of phandle and reset specifier pairs as listed + in reset-names property + +- reset-names: + Usage: required for ipq/apq8064 + Value type: <stringlist> + Definition: Should contain the following entries + - "axi" AXI reset + - "ahb" AHB reset + - "por" POR reset + - "pci" PCI reset + - "phy" PHY reset + +- reset-names: + Usage: required for apq8084 + Value type: <stringlist> + Definition: Should contain the following entries + - "core" Core reset + +- reset-names: + Usage: required for ipq/apq8064 + Value type: <stringlist> + Definition: Should contain the following entries + - "axi_m" AXI master reset + - "axi_s" AXI slave reset + - "pipe" PIPE reset + - "axi_m_vmid" VMID reset + - "axi_s_xpu" XPU reset + - "parf" PARF reset + - "phy" PHY reset + - "axi_m_sticky" AXI sticky reset + - "pipe_sticky" PIPE sticky reset + - "pwr" PWR reset + - "ahb" AHB reset + - "phy_ahb" PHY AHB reset + +- reset-names: + Usage: required for ipq8074 + Value type: <stringlist> + Definition: Should contain the following entries + - "pipe" PIPE reset + - "sleep" Sleep reset + - "sticky" Core Sticky reset + - "axi_m" AXI Master reset + - "axi_s" AXI Slave reset + - "ahb" AHB Reset + - "axi_m_sticky" AXI Master Sticky reset + +- power-domains: + Usage: required for apq8084 and msm8996/apq8096 + Value type: <prop-encoded-array> + Definition: A phandle and power domain specifier pair to the + power domain which is responsible for collapsing + and restoring power to the peripheral + +- vdda-supply: + Usage: required + Value type: <phandle> + Definition: A phandle to the core analog power supply + +- vdda_phy-supply: + Usage: required for ipq/apq8064 + Value type: <phandle> + Definition: A phandle to the analog power supply for PHY + +- vdda_refclk-supply: + Usage: required for ipq/apq8064 + Value type: <phandle> + Definition: A phandle to the analog power supply for IC which generates + reference clock +- vddpe-3v3-supply: + Usage: optional + Value type: <phandle> + Definition: A phandle to the PCIe endpoint power supply + +- phys: + Usage: required for apq8084 + Value type: <phandle> + Definition: List of phandle(s) as listed in phy-names property + +- phy-names: + Usage: required for apq8084 + Value type: <stringlist> + Definition: Should contain "pciephy" + +- <name>-gpios: + Usage: optional + Value type: <prop-encoded-array> + Definition: List of phandle and GPIO specifier pairs. Should contain + - "perst-gpios" PCIe endpoint reset signal line + - "wake-gpios" PCIe endpoint wake signal line + +* Example for ipq/apq8064 + pcie@1b500000 { + compatible = "qcom,pcie-apq8064", "qcom,pcie-ipq8064", "snps,dw-pcie"; + reg = <0x1b500000 0x1000 + 0x1b502000 0x80 + 0x1b600000 0x100 + 0x0ff00000 0x100000>; + reg-names = "dbi", "elbi", "parf", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000 /* I/O */ + 0x82000000 0 0 0x08000000 0 0x07e00000>; /* memory */ + interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + clocks = <&gcc PCIE_A_CLK>, + <&gcc PCIE_H_CLK>, + <&gcc PCIE_PHY_CLK>; + clock-names = "core", "iface", "phy"; + resets = <&gcc PCIE_ACLK_RESET>, + <&gcc PCIE_HCLK_RESET>, + <&gcc PCIE_POR_RESET>, + <&gcc PCIE_PCI_RESET>, + <&gcc PCIE_PHY_RESET>; + reset-names = "axi", "ahb", "por", "pci", "phy"; + pinctrl-0 = <&pcie_pins_default>; + pinctrl-names = "default"; + }; + +* Example for apq8084 + pcie0@fc520000 { + compatible = "qcom,pcie-apq8084", "snps,dw-pcie"; + reg = <0xfc520000 0x2000>, + <0xff000000 0x1000>, + <0xff001000 0x1000>, + <0xff002000 0x2000>; + reg-names = "parf", "dbi", "elbi", "config"; + device_type = "pci"; + linux,pci-domain = <0>; + bus-range = <0x00 0xff>; + num-lanes = <1>; + #address-cells = <3>; + #size-cells = <2>; + ranges = <0x81000000 0 0 0xff200000 0 0x00100000 /* I/O */ + 0x82000000 0 0x00300000 0xff300000 0 0x00d00000>; /* memory */ + interrupts = <GIC_SPI 243 IRQ_TYPE_NONE>; + interrupt-names = "msi"; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0x7>; + interrupt-map = <0 0 0 1 &intc 0 244 IRQ_TYPE_LEVEL_HIGH>, /* int_a */ + <0 0 0 2 &intc 0 245 IRQ_TYPE_LEVEL_HIGH>, /* int_b */ + <0 0 0 3 &intc 0 247 IRQ_TYPE_LEVEL_HIGH>, /* int_c */ + <0 0 0 4 &intc 0 248 IRQ_TYPE_LEVEL_HIGH>; /* int_d */ + clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>, + <&gcc GCC_PCIE_0_MSTR_AXI_CLK>, + <&gcc GCC_PCIE_0_SLV_AXI_CLK>, + <&gcc GCC_PCIE_0_AUX_CLK>; + clock-names = "iface", "master_bus", "slave_bus", "aux"; + resets = <&gcc GCC_PCIE_0_BCR>; + reset-names = "core"; + power-domains = <&gcc PCIE0_GDSC>; + vdda-supply = <&pma8084_l3>; + phys = <&pciephy0>; + phy-names = "pciephy"; + perst-gpio = <&tlmm 70 GPIO_ACTIVE_LOW>; + pinctrl-0 = <&pcie0_pins_default>; + pinctrl-names = "default"; + }; diff --git a/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt b/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt new file mode 100644 index 000000000..ffba4f63d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/ralink,rt3883-pci.txt @@ -0,0 +1,187 @@ +* Mediatek/Ralink RT3883 PCI controller + +1) Main node + + Required properties: + + - compatible: must be "ralink,rt3883-pci" + + - reg: specifies the physical base address of the controller and + the length of the memory mapped region. + + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 1. + + - #size-cells: specifies the number of cells used to represent the size + of an address. The value must be 1. + + - ranges: specifies the translation between child address space and parent + address space + + Optional properties: + + - status: indicates the operational status of the device. + Value must be either "disabled" or "okay". + +2) Child nodes + + The main node must have two child nodes which describes the built-in + interrupt controller and the PCI host bridge. + + a) Interrupt controller: + + Required properties: + + - interrupt-controller: identifies the node as an interrupt controller + + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. As such, 'interrupt-map' nodes do not + have to specify a parent unit address. + + - #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + + - interrupts: specifies the interrupt source of the parent interrupt + controller. The format of the interrupt specifier depends on the + parent interrupt controller. + + b) PCI host bridge: + + Required properties: + + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. + + - #size-cells: specifies the number of cells used to represent the size + of an address. The value must be 2. + + - #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + + - device_type: must be "pci" + + - bus-range: PCI bus numbers covered + + - ranges: specifies the ranges for the PCI memory and I/O regions + + - interrupt-map-mask, + - interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. + + The PCI host bridge node might have additional sub-nodes representing + the onboard PCI devices/PCI slots. Each such sub-node must have the + following mandatory properties: + + - reg: used only for interrupt mapping, so only the first four bytes + are used to refer to the correct bus number and device number. + + - device_type: must be "pci" + + If a given sub-node represents a PCI bridge it must have following + mandatory properties as well: + + - #address-cells: must be set to <3> + + - #size-cells: must set to <2> + + - #interrupt-cells: must be set to <1> + + - interrupt-map-mask, + - interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. + + Besides the required properties the sub-nodes may have these optional + properties: + + - status: indicates the operational status of the sub-node. + Value must be either "disabled" or "okay". + +3) Example: + + a) SoC specific dtsi file: + + pci@10140000 { + compatible = "ralink,rt3883-pci"; + reg = <0x10140000 0x20000>; + #address-cells = <1>; + #size-cells = <1>; + ranges; /* direct mapping */ + + status = "disabled"; + + pciintc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + + interrupt-parent = <&cpuintc>; + interrupts = <4>; + }; + + host-bridge { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + + device_type = "pci"; + + bus-range = <0 255>; + ranges = < + 0x02000000 0 0x00000000 0x20000000 0 0x10000000 /* pci memory */ + 0x01000000 0 0x00000000 0x10160000 0 0x00010000 /* io space */ + >; + + interrupt-map-mask = <0xf800 0 0 7>; + interrupt-map = < + /* IDSEL 17 */ + 0x8800 0 0 1 &pciintc 18 + 0x8800 0 0 2 &pciintc 18 + 0x8800 0 0 3 &pciintc 18 + 0x8800 0 0 4 &pciintc 18 + /* IDSEL 18 */ + 0x9000 0 0 1 &pciintc 19 + 0x9000 0 0 2 &pciintc 19 + 0x9000 0 0 3 &pciintc 19 + 0x9000 0 0 4 &pciintc 19 + >; + + pci-bridge@1 { + reg = <0x0800 0 0 0 0>; + device_type = "pci"; + #interrupt-cells = <1>; + #address-cells = <3>; + #size-cells = <2>; + + interrupt-map-mask = <0x0 0 0 0>; + interrupt-map = <0x0 0 0 0 &pciintc 20>; + + status = "disabled"; + }; + + pci-slot@17 { + reg = <0x8800 0 0 0 0>; + device_type = "pci"; + + status = "disabled"; + }; + + pci-slot@18 { + reg = <0x9000 0 0 0 0>; + device_type = "pci"; + + status = "disabled"; + }; + }; + }; + + b) Board specific dts file: + + pci@10140000 { + status = "okay"; + + host-bridge { + pci-bridge@1 { + status = "okay"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt b/Documentation/devicetree/bindings/pci/rcar-pci.txt new file mode 100644 index 000000000..a5f7fc62d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt @@ -0,0 +1,64 @@ +* Renesas R-Car PCIe interface + +Required properties: +compatible: "renesas,pcie-r8a7743" for the R8A7743 SoC; + "renesas,pcie-r8a7779" for the R8A7779 SoC; + "renesas,pcie-r8a7790" for the R8A7790 SoC; + "renesas,pcie-r8a7791" for the R8A7791 SoC; + "renesas,pcie-r8a7793" for the R8A7793 SoC; + "renesas,pcie-r8a7795" for the R8A7795 SoC; + "renesas,pcie-r8a7796" for the R8A7796 SoC; + "renesas,pcie-r8a77980" for the R8A77980 SoC; + "renesas,pcie-rcar-gen2" for a generic R-Car Gen2 or + RZ/G1 compatible device. + "renesas,pcie-rcar-gen3" for a generic R-Car Gen3 compatible device. + + When compatible with the generic version, nodes must list the + SoC-specific version corresponding to the platform first + followed by the generic version. + +- reg: base address and length of the PCIe controller registers. +- #address-cells: set to <3> +- #size-cells: set to <2> +- bus-range: PCI bus numbers covered +- device_type: set to "pci" +- ranges: ranges for the PCI memory and I/O regions. +- dma-ranges: ranges for the inbound memory regions. +- interrupts: two interrupt sources for MSI interrupts, followed by interrupt + source for hardware related interrupts (e.g. link speed change). +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt numbers. +- clocks: from common clock binding: clock specifiers for the PCIe controller + and PCIe bus clocks. +- clock-names: from common clock binding: should be "pcie" and "pcie_bus". + +Optional properties: +- phys: from common PHY binding: PHY phandle and specifier (only make sense + for R-Car gen3 SoCs where the PCIe PHYs have their own register blocks). +- phy-names: from common PHY binding: should be "pcie". + +Example: + +SoC-specific DT Entry: + + pcie: pcie@fe000000 { + compatible = "renesas,pcie-r8a7791", "renesas,pcie-rcar-gen2"; + reg = <0 0xfe000000 0 0x80000>; + #address-cells = <3>; + #size-cells = <2>; + bus-range = <0x00 0xff>; + device_type = "pci"; + ranges = <0x01000000 0 0x00000000 0 0xfe100000 0 0x00100000 + 0x02000000 0 0xfe200000 0 0xfe200000 0 0x00200000 + 0x02000000 0 0x30000000 0 0x30000000 0 0x08000000 + 0x42000000 0 0x38000000 0 0x38000000 0 0x08000000>; + dma-ranges = <0x42000000 0 0x40000000 0 0x40000000 0 0x40000000 + 0x42000000 2 0x00000000 2 0x00000000 0 0x40000000>; + interrupts = <0 116 4>, <0 117 4>, <0 118 4>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic 0 116 4>; + clocks = <&mstp3_clks R8A7791_CLK_PCIE>, <&pcie_bus_clk>; + clock-names = "pcie", "pcie_bus"; + }; diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie-ep.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie-ep.txt new file mode 100644 index 000000000..778467307 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie-ep.txt @@ -0,0 +1,62 @@ +* Rockchip AXI PCIe Endpoint Controller DT description + +Required properties: +- compatible: Should contain "rockchip,rk3399-pcie-ep" +- reg: Two register ranges as listed in the reg-names property +- reg-names: Must include the following names + - "apb-base" + - "mem-base" +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "aclk" + - "aclk-perf" + - "hclk" + - "pm" +- resets: Must contain seven entries for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following names + - "core" + - "mgmt" + - "mgmt-sticky" + - "pipe" + - "pm" + - "aclk" + - "pclk" +- pinctrl-names : The pin control state names +- pinctrl-0: The "default" pinctrl state +- phys: Must contain an phandle to a PHY for each entry in phy-names. +- phy-names: Must include 4 entries for all 4 lanes even if some of + them won't be used for your cases. Entries are of the form "pcie-phy-N": + where N ranges from 0 to 3. + (see example below and you MUST also refer to ../phy/rockchip-pcie-phy.txt + for changing the #phy-cells of phy node to support it) +- rockchip,max-outbound-regions: Maximum number of outbound regions + +Optional Property: +- num-lanes: number of lanes to use +- max-functions: Maximum number of functions that can be configured (default 1). + +pcie0-ep: pcie@f8000000 { + compatible = "rockchip,rk3399-pcie-ep"; + #address-cells = <3>; + #size-cells = <2>; + rockchip,max-outbound-regions = <16>; + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, + <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>; + clock-names = "aclk", "aclk-perf", + "hclk", "pm"; + max-functions = /bits/ 8 <8>; + num-lanes = <4>; + reg = <0x0 0xfd000000 0x0 0x1000000>, <0x0 0x80000000 0x0 0x20000>; + reg-names = "apb-base", "mem-base"; + resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE> , + <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>; + reset-names = "core", "mgmt", "mgmt-sticky", "pipe", + "pm", "pclk", "aclk"; + phys = <&pcie_phy 0>, <&pcie_phy 1>, <&pcie_phy 2>, <&pcie_phy 3>; + phy-names = "pcie-phy-0", "pcie-phy-1", "pcie-phy-2", "pcie-phy-3"; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_clkreq>; +}; diff --git a/Documentation/devicetree/bindings/pci/rockchip-pcie-host.txt b/Documentation/devicetree/bindings/pci/rockchip-pcie-host.txt new file mode 100644 index 000000000..af34c6577 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/rockchip-pcie-host.txt @@ -0,0 +1,135 @@ +* Rockchip AXI PCIe Root Port Bridge DT description + +Required properties: +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- compatible: Should contain "rockchip,rk3399-pcie" +- reg: Two register ranges as listed in the reg-names property +- reg-names: Must include the following names + - "axi-base" + - "apb-base" +- clocks: Must contain an entry for each entry in clock-names. + See ../clocks/clock-bindings.txt for details. +- clock-names: Must include the following entries: + - "aclk" + - "aclk-perf" + - "hclk" + - "pm" +- msi-map: Maps a Requester ID to an MSI controller and associated + msi-specifier data. See ./pci-msi.txt +- interrupts: Three interrupt entries must be specified. +- interrupt-names: Must include the following names + - "sys" + - "legacy" + - "client" +- resets: Must contain seven entries for each entry in reset-names. + See ../reset/reset.txt for details. +- reset-names: Must include the following names + - "core" + - "mgmt" + - "mgmt-sticky" + - "pipe" + - "pm" + - "aclk" + - "pclk" +- pinctrl-names : The pin control state names +- pinctrl-0: The "default" pinctrl state +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- interrupt-map-mask and interrupt-map: standard PCI properties + +Required properties for legacy PHY model (deprecated): +- phys: From PHY bindings: Phandle for the Generic PHY for PCIe. +- phy-names: MUST be "pcie-phy". + +Required properties for per-lane PHY model (preferred): +- phys: Must contain an phandle to a PHY for each entry in phy-names. +- phy-names: Must include 4 entries for all 4 lanes even if some of + them won't be used for your cases. Entries are of the form "pcie-phy-N": + where N ranges from 0 to 3. + (see example below and you MUST also refer to ../phy/rockchip-pcie-phy.txt + for changing the #phy-cells of phy node to support it) + +Optional Property: +- aspm-no-l0s: RC won't support ASPM L0s. This property is needed if + using 24MHz OSC for RC's PHY. +- ep-gpios: contain the entry for pre-reset GPIO +- num-lanes: number of lanes to use +- vpcie12v-supply: The phandle to the 12v regulator to use for PCIe. +- vpcie3v3-supply: The phandle to the 3.3v regulator to use for PCIe. +- vpcie1v8-supply: The phandle to the 1.8v regulator to use for PCIe. +- vpcie0v9-supply: The phandle to the 0.9v regulator to use for PCIe. + +*Interrupt controller child node* +The core controller provides a single interrupt for legacy INTx. The PCIe node +should contain an interrupt controller node as a target for the PCI +'interrupt-map' property. This node represents the domain at which the four +INTx interrupts are decoded and routed. + + +Required properties for Interrupt controller child node: +- interrupt-controller: identifies the node as an interrupt controller +- #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + +Example: + +pcie0: pcie@f8000000 { + compatible = "rockchip,rk3399-pcie"; + #address-cells = <3>; + #size-cells = <2>; + clocks = <&cru ACLK_PCIE>, <&cru ACLK_PERF_PCIE>, + <&cru PCLK_PCIE>, <&cru SCLK_PCIE_PM>; + clock-names = "aclk", "aclk-perf", + "hclk", "pm"; + bus-range = <0x0 0x1>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "sys", "legacy", "client"; + assigned-clocks = <&cru SCLK_PCIEPHY_REF>; + assigned-clock-parents = <&cru SCLK_PCIEPHY_REF100M>; + assigned-clock-rates = <100000000>; + ep-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>; + ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x600000 + 0x81000000 0x0 0xfa600000 0x0 0xfa600000 0x0 0x100000>; + num-lanes = <4>; + msi-map = <0x0 &its 0x0 0x1000>; + reg = <0x0 0xf8000000 0x0 0x2000000>, <0x0 0xfd000000 0x0 0x1000000>; + reg-names = "axi-base", "apb-base"; + resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>, + <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE> , + <&cru SRST_PCIE_PM>, <&cru SRST_P_PCIE>, <&cru SRST_A_PCIE>; + reset-names = "core", "mgmt", "mgmt-sticky", "pipe", + "pm", "pclk", "aclk"; + /* deprecated legacy PHY model */ + phys = <&pcie_phy>; + phy-names = "pcie-phy"; + pinctrl-names = "default"; + pinctrl-0 = <&pcie_clkreq>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie0_intc 0>, + <0 0 0 2 &pcie0_intc 1>, + <0 0 0 3 &pcie0_intc 2>, + <0 0 0 4 &pcie0_intc 3>; + pcie0_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; +}; + +pcie0: pcie@f8000000 { + ... + + /* preferred per-lane PHY model */ + phys = <&pcie_phy 0>, <&pcie_phy 1>, <&pcie_phy 2>, <&pcie_phy 3>; + phy-names = "pcie-phy-0", "pcie-phy-1", "pcie-phy-2", "pcie-phy-3"; + + ... +}; diff --git a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt new file mode 100644 index 000000000..651d957d1 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt @@ -0,0 +1,58 @@ +* Samsung Exynos 5440 PCIe interface + +This PCIe host controller is based on the Synopsys DesignWare PCIe IP +and thus inherits all the common properties defined in designware-pcie.txt. + +Required properties: +- compatible: "samsung,exynos5440-pcie" +- reg: base addresses and lengths of the PCIe controller, +- reg-names : First name should be set to "elbi". + And use the "config" instead of getting the configuration address space + from "ranges". + NOTE: When using the "config" property, reg-names must be set. +- interrupts: A list of interrupt outputs for level interrupt, + pulse interrupt, special interrupt. +- phys: From PHY binding. Phandle for the generic PHY. + Refer to Documentation/devicetree/bindings/phy/samsung-phy.txt + +For other common properties, refer to + Documentation/devicetree/bindings/pci/designware-pcie.txt + +Example: + +SoC-specific DT Entry (with using PHY framework): + + pcie_phy0: pcie-phy@270000 { + ... + reg = <0x270000 0x1000>, <0x271000 0x40>; + reg-names = "phy", "block"; + ... + }; + + pcie@290000 { + compatible = "samsung,exynos5440-pcie", "snps,dw-pcie"; + reg = <0x290000 0x1000>, <0x40000000 0x1000>; + reg-names = "elbi", "config"; + clocks = <&clock 28>, <&clock 27>; + clock-names = "pcie", "pcie_bus"; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + phys = <&pcie_phy0>; + ranges = <0x81000000 0 0 0x60001000 0 0x00010000 + 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; + #interrupt-cells = <1>; + interrupt-map-mask = <0 0 0 0>; + interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + num-lanes = <4>; + }; + +Board-specific DT Entry: + + pcie@290000 { + reset-gpio = <&pin_ctrl 5 0>; + }; + + pcie@2a0000 { + reset-gpio = <&pin_ctrl 22 0>; + }; diff --git a/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt b/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt new file mode 100644 index 000000000..d5a14f5da --- /dev/null +++ b/Documentation/devicetree/bindings/pci/spear13xx-pcie.txt @@ -0,0 +1,14 @@ +SPEAr13XX PCIe DT detail: +================================ + +SPEAr13XX uses the Synopsys DesignWare PCIe controller and ST MiPHY as PHY +controller. + +Required properties: +- compatible : should be "st,spear1340-pcie", "snps,dw-pcie". +- phys : phandle to PHY node associated with PCIe controller +- phy-names : must be "pcie-phy" +- All other definitions as per generic PCI bindings + + Optional properties: +- st,pcie-is-gen1 indicates that forced gen1 initialization is needed. diff --git a/Documentation/devicetree/bindings/pci/tango-pcie.txt b/Documentation/devicetree/bindings/pci/tango-pcie.txt new file mode 100644 index 000000000..244683836 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/tango-pcie.txt @@ -0,0 +1,29 @@ +Sigma Designs Tango PCIe controller + +Required properties: + +- compatible: "sigma,smp8759-pcie" +- reg: address/size of PCI configuration space, address/size of register area +- bus-range: defined by size of PCI configuration space +- device_type: "pci" +- #size-cells: <2> +- #address-cells: <3> +- msi-controller +- ranges: translation from system to bus addresses +- interrupts: spec for misc interrupts, spec for MSI + +Example: + + pcie@2e000 { + compatible = "sigma,smp8759-pcie"; + reg = <0x50000000 0x400000>, <0x2e000 0x100>; + bus-range = <0 3>; + device_type = "pci"; + #size-cells = <2>; + #address-cells = <3>; + msi-controller; + ranges = <0x02000000 0x0 0x00400000 0x50400000 0x0 0x3c00000>; + interrupts = + <54 IRQ_TYPE_LEVEL_HIGH>, /* misc interrupts */ + <55 IRQ_TYPE_LEVEL_HIGH>; /* MSI */ + }; diff --git a/Documentation/devicetree/bindings/pci/ti-pci.txt b/Documentation/devicetree/bindings/pci/ti-pci.txt new file mode 100644 index 000000000..7f7af3044 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/ti-pci.txt @@ -0,0 +1,90 @@ +TI PCI Controllers + +PCIe DesignWare Controller + - compatible: Should be "ti,dra7-pcie" for RC + Should be "ti,dra7-pcie-ep" for EP + - phys : list of PHY specifiers (used by generic PHY framework) + - phy-names : must be "pcie-phy0", "pcie-phy1", "pcie-phyN".. based on the + number of PHYs as specified in *phys* property. + - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>", + where <X> is the instance number of the pcie from the HW spec. + - num-lanes as specified in ../designware-pcie.txt + +HOST MODE +========= + - reg : Two register ranges as listed in the reg-names property + - reg-names : The first entry must be "ti-conf" for the TI-specific registers + The second entry must be "rc-dbics" for the DesignWare PCIe + registers + The third entry must be "config" for the PCIe configuration space + - interrupts : Two interrupt entries must be specified. The first one is for + main interrupt line and the second for MSI interrupt line. + - #address-cells, + #size-cells, + #interrupt-cells, + device_type, + ranges, + interrupt-map-mask, + interrupt-map : as specified in ../designware-pcie.txt + +DEVICE MODE +=========== + - reg : Four register ranges as listed in the reg-names property + - reg-names : "ti-conf" for the TI-specific registers + "ep_dbics" for the standard configuration registers as + they are locally accessed within the DIF CS space + "ep_dbics2" for the standard configuration registers as + they are locally accessed within the DIF CS2 space + "addr_space" used to map remote RC address space + - interrupts : one interrupt entries must be specified for main interrupt. + - num-ib-windows : number of inbound address translation windows + - num-ob-windows : number of outbound address translation windows + - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument + should contain the register offset within syscon + and the 2nd argument should contain the bit field + for setting the bit to enable unaligned + access. + +Optional Property: + - gpios : Should be added if a GPIO line is required to drive PERST# line + +NOTE: Two DT nodes may be added for each PCI controller; one for host +mode and another for device mode. So in order for PCI to +work in host mode, EP mode DT node should be disabled and in order to PCI to +work in EP mode, host mode DT node should be disabled. Host mode and EP +mode are mutually exclusive. + +Example: +axi { + compatible = "simple-bus"; + #size-cells = <1>; + #address-cells = <1>; + ranges = <0x51000000 0x51000000 0x3000 + 0x0 0x20000000 0x10000000>; + pcie@51000000 { + compatible = "ti,dra7-pcie"; + reg = <0x51000000 0x2000>, <0x51002000 0x14c>, <0x1000 0x2000>; + reg-names = "rc_dbics", "ti_conf", "config"; + interrupts = <0 232 0x4>, <0 233 0x4>; + #address-cells = <3>; + #size-cells = <2>; + device_type = "pci"; + ranges = <0x81000000 0 0 0x03000 0 0x00010000 + 0x82000000 0 0x20013000 0x13000 0 0xffed000>; + #interrupt-cells = <1>; + num-lanes = <1>; + ti,hwmods = "pcie1"; + phys = <&pcie1_phy>; + phy-names = "pcie-phy0"; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt new file mode 100644 index 000000000..11063293f --- /dev/null +++ b/Documentation/devicetree/bindings/pci/v3-v360epc-pci.txt @@ -0,0 +1,76 @@ +V3 Semiconductor V360 EPC PCI bridge + +This bridge is found in the ARM Integrator/AP (Application Platform) + +Required properties: +- compatible: should be one of: + "v3,v360epc-pci" + "arm,integrator-ap-pci", "v3,v360epc-pci" +- reg: should contain two register areas: + first the base address of the V3 host bridge controller, 64KB + second the configuration area register space, 16MB +- interrupts: should contain a reference to the V3 error interrupt + as routed on the system. +- bus-range: see pci.txt +- ranges: this follows the standard PCI bindings in the IEEE Std + 1275-1994 (see pci.txt) with the following restriction: + - The non-prefetchable and prefetchable memory windows must + each be exactly 256MB (0x10000000) in size. + - The prefetchable memory window must be immediately adjacent + to the non-prefetcable memory window +- dma-ranges: three ranges for the inbound memory region. The ranges must + be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, + 64MB, 128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked + as pre-fetchable. Two ranges are supported by the hardware. + +Integrator-specific required properties: +- syscon: should contain a link to the syscon device node, since + on the Integrator, some registers in the syscon are required to + operate the V3 host bridge. + +Example: + +pci: pciv3@62000000 { + compatible = "arm,integrator-ap-pci", "v3,v360epc-pci"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = <0x62000000 0x10000>, <0x61000000 0x01000000>; + interrupt-parent = <&pic>; + interrupts = <17>; /* Bus error IRQ */ + clocks = <&pciclk>; + bus-range = <0x00 0xff>; + ranges = 0x01000000 0 0x00000000 /* I/O space @00000000 */ + 0x60000000 0 0x01000000 /* 16 MiB @ LB 60000000 */ + 0x02000000 0 0x40000000 /* non-prefectable memory @40000000 */ + 0x40000000 0 0x10000000 /* 256 MiB @ LB 40000000 1:1 */ + 0x42000000 0 0x50000000 /* prefetchable memory @50000000 */ + 0x50000000 0 0x10000000>; /* 256 MiB @ LB 50000000 1:1 */ + dma-ranges = <0x02000000 0 0x20000000 /* EBI memory space */ + 0x20000000 0 0x20000000 /* 512 MB @ LB 20000000 1:1 */ + 0x02000000 0 0x80000000 /* Core module alias memory */ + 0x80000000 0 0x40000000>; /* 1GB @ LB 80000000 */ + interrupt-map-mask = <0xf800 0 0 0x7>; + interrupt-map = < + /* IDSEL 9 */ + 0x4800 0 0 1 &pic 13 /* INT A on slot 9 is irq 13 */ + 0x4800 0 0 2 &pic 14 /* INT B on slot 9 is irq 14 */ + 0x4800 0 0 3 &pic 15 /* INT C on slot 9 is irq 15 */ + 0x4800 0 0 4 &pic 16 /* INT D on slot 9 is irq 16 */ + /* IDSEL 10 */ + 0x5000 0 0 1 &pic 14 /* INT A on slot 10 is irq 14 */ + 0x5000 0 0 2 &pic 15 /* INT B on slot 10 is irq 15 */ + 0x5000 0 0 3 &pic 16 /* INT C on slot 10 is irq 16 */ + 0x5000 0 0 4 &pic 13 /* INT D on slot 10 is irq 13 */ + /* IDSEL 11 */ + 0x5800 0 0 1 &pic 15 /* INT A on slot 11 is irq 15 */ + 0x5800 0 0 2 &pic 16 /* INT B on slot 11 is irq 16 */ + 0x5800 0 0 3 &pic 13 /* INT C on slot 11 is irq 13 */ + 0x5800 0 0 4 &pic 14 /* INT D on slot 11 is irq 14 */ + /* IDSEL 12 */ + 0x6000 0 0 1 &pic 16 /* INT A on slot 12 is irq 16 */ + 0x6000 0 0 2 &pic 13 /* INT B on slot 12 is irq 13 */ + 0x6000 0 0 3 &pic 14 /* INT C on slot 12 is irq 14 */ + 0x6000 0 0 4 &pic 15 /* INT D on slot 12 is irq 15 */ + >; +}; diff --git a/Documentation/devicetree/bindings/pci/versatile.txt b/Documentation/devicetree/bindings/pci/versatile.txt new file mode 100644 index 000000000..0a702b13d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/versatile.txt @@ -0,0 +1,59 @@ +* ARM Versatile Platform Baseboard PCI interface + +PCI host controller found on the ARM Versatile PB board's FPGA. + +Required properties: +- compatible: should contain "arm,versatile-pci" to identify the Versatile PCI + controller. +- reg: base addresses and lengths of the PCI controller. There must be 3 + entries: + - Versatile-specific registers + - Self Config space + - Config space +- #address-cells: set to <3> +- #size-cells: set to <2> +- device_type: set to "pci" +- bus-range: set to <0 0xff> +- ranges: ranges for the PCI memory and I/O regions +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties to define + the mapping of the PCI interface to interrupt numbers. + +Example: + +pci-controller@10001000 { + compatible = "arm,versatile-pci"; + device_type = "pci"; + reg = <0x10001000 0x1000 + 0x41000000 0x10000 + 0x42000000 0x100000>; + bus-range = <0 0xff>; + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + + ranges = <0x01000000 0 0x00000000 0x43000000 0 0x00010000 /* downstream I/O */ + 0x02000000 0 0x50000000 0x50000000 0 0x10000000 /* non-prefetchable memory */ + 0x42000000 0 0x60000000 0x60000000 0 0x10000000>; /* prefetchable memory */ + + interrupt-map-mask = <0x1800 0 0 7>; + interrupt-map = <0x1800 0 0 1 &sic 28 + 0x1800 0 0 2 &sic 29 + 0x1800 0 0 3 &sic 30 + 0x1800 0 0 4 &sic 27 + + 0x1000 0 0 1 &sic 27 + 0x1000 0 0 2 &sic 28 + 0x1000 0 0 3 &sic 29 + 0x1000 0 0 4 &sic 30 + + 0x0800 0 0 1 &sic 30 + 0x0800 0 0 2 &sic 27 + 0x0800 0 0 3 &sic 28 + 0x0800 0 0 4 &sic 29 + + 0x0000 0 0 1 &sic 29 + 0x0000 0 0 2 &sic 30 + 0x0000 0 0 3 &sic 27 + 0x0000 0 0 4 &sic 28>; +}; diff --git a/Documentation/devicetree/bindings/pci/xgene-pci-msi.txt b/Documentation/devicetree/bindings/pci/xgene-pci-msi.txt new file mode 100644 index 000000000..85d9b9523 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xgene-pci-msi.txt @@ -0,0 +1,68 @@ +* AppliedMicro X-Gene v1 PCIe MSI controller + +Required properties: + +- compatible: should be "apm,xgene1-msi" to identify + X-Gene v1 PCIe MSI controller block. +- msi-controller: indicates that this is an X-Gene v1 PCIe MSI controller node +- reg: physical base address (0x79000000) and length (0x900000) for controller + registers. These registers include the MSI termination address and data + registers as well as the MSI interrupt status registers. +- reg-names: not required +- interrupts: A list of 16 interrupt outputs of the controller, starting from + interrupt number 0x10 to 0x1f. +- interrupt-names: not required + +Each PCIe node needs to have property msi-parent that points to an MSI +controller node + +Examples: + +SoC DTSI: + + + MSI node: + msi@79000000 { + compatible = "apm,xgene1-msi"; + msi-controller; + reg = <0x00 0x79000000 0x0 0x900000>; + interrupts = <0x0 0x10 0x4> + <0x0 0x11 0x4> + <0x0 0x12 0x4> + <0x0 0x13 0x4> + <0x0 0x14 0x4> + <0x0 0x15 0x4> + <0x0 0x16 0x4> + <0x0 0x17 0x4> + <0x0 0x18 0x4> + <0x0 0x19 0x4> + <0x0 0x1a 0x4> + <0x0 0x1b 0x4> + <0x0 0x1c 0x4> + <0x0 0x1d 0x4> + <0x0 0x1e 0x4> + <0x0 0x1f 0x4>; + }; + + + PCIe controller node with msi-parent property pointing to MSI node: + pcie0: pcie@1f2b0000 { + device_type = "pci"; + compatible = "apm,xgene-storm-pcie", "apm,xgene-pcie"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = < 0x00 0x1f2b0000 0x0 0x00010000 /* Controller registers */ + 0xe0 0xd0000000 0x0 0x00040000>; /* PCI config space */ + reg-names = "csr", "cfg"; + ranges = <0x01000000 0x00 0x00000000 0xe0 0x10000000 0x00 0x00010000 /* io */ + 0x02000000 0x00 0x80000000 0xe1 0x80000000 0x00 0x80000000>; /* mem */ + dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000 + 0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>; + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc2 0x1 + 0x0 0x0 0x0 0x2 &gic 0x0 0xc3 0x1 + 0x0 0x0 0x0 0x3 &gic 0x0 0xc4 0x1 + 0x0 0x0 0x0 0x4 &gic 0x0 0xc5 0x1>; + dma-coherent; + clocks = <&pcie0clk 0>; + msi-parent= <&msi>; + }; diff --git a/Documentation/devicetree/bindings/pci/xgene-pci.txt b/Documentation/devicetree/bindings/pci/xgene-pci.txt new file mode 100644 index 000000000..92490330d --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xgene-pci.txt @@ -0,0 +1,50 @@ +* AppliedMicro X-Gene PCIe interface + +Required properties: +- device_type: set to "pci" +- compatible: should contain "apm,xgene-pcie" to identify the core. +- reg: A list of physical base address and length for each set of controller + registers. Must contain an entry for each entry in the reg-names + property. +- reg-names: Must include the following entries: + "csr": controller configuration registers. + "cfg": PCIe configuration space registers. +- #address-cells: set to <3> +- #size-cells: set to <2> +- ranges: ranges for the outbound memory, I/O regions. +- dma-ranges: ranges for the inbound memory regions. +- #interrupt-cells: set to <1> +- interrupt-map-mask and interrupt-map: standard PCI properties + to define the mapping of the PCIe interface to interrupt + numbers. +- clocks: from common clock binding: handle to pci clock. + +Optional properties: +- status: Either "ok" or "disabled". +- dma-coherent: Present if DMA operations are coherent + +Example: + + pcie0: pcie@1f2b0000 { + status = "disabled"; + device_type = "pci"; + compatible = "apm,xgene-storm-pcie", "apm,xgene-pcie"; + #interrupt-cells = <1>; + #size-cells = <2>; + #address-cells = <3>; + reg = < 0x00 0x1f2b0000 0x0 0x00010000 /* Controller registers */ + 0xe0 0xd0000000 0x0 0x00040000>; /* PCI config space */ + reg-names = "csr", "cfg"; + ranges = <0x01000000 0x00 0x00000000 0xe0 0x10000000 0x00 0x00010000 /* io */ + 0x02000000 0x00 0x80000000 0xe1 0x80000000 0x00 0x80000000>; /* mem */ + dma-ranges = <0x42000000 0x80 0x00000000 0x80 0x00000000 0x00 0x80000000 + 0x42000000 0x00 0x00000000 0x00 0x00000000 0x80 0x00000000>; + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0x0 0x0 0x0 0x1 &gic 0x0 0xc2 0x1 + 0x0 0x0 0x0 0x2 &gic 0x0 0xc3 0x1 + 0x0 0x0 0x0 0x3 &gic 0x0 0xc4 0x1 + 0x0 0x0 0x0 0x4 &gic 0x0 0xc5 0x1>; + dma-coherent; + clocks = <&pcie0clk 0>; + }; + diff --git a/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt new file mode 100644 index 000000000..01bf7fdf4 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xilinx-nwl-pcie.txt @@ -0,0 +1,70 @@ +* Xilinx NWL PCIe Root Port Bridge DT description + +Required properties: +- compatible: Should contain "xlnx,nwl-pcie-2.11" +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- reg: Should contain Bridge, PCIe Controller registers location, + configuration space, and length +- reg-names: Must include the following entries: + "breg": bridge registers + "pcireg": PCIe controller registers + "cfg": configuration space region +- device_type: must be "pci" +- interrupts: Should contain NWL PCIe interrupt +- interrupt-names: Must include the following entries: + "msi1, msi0": interrupt asserted when an MSI is received + "intx": interrupt asserted when a legacy interrupt is received + "misc": interrupt asserted when miscellaneous interrupt is received +- interrupt-map-mask and interrupt-map: standard PCI properties to define the + mapping of the PCI interface to interrupt numbers. +- ranges: ranges for the PCI memory regions (I/O space region is not + supported by hardware) + Please refer to the standard PCI bus binding document for a more + detailed explanation +- msi-controller: indicates that this is MSI controller node +- msi-parent: MSI parent of the root complex itself +- legacy-interrupt-controller: Interrupt controller device node for Legacy + interrupts + - interrupt-controller: identifies the node as an interrupt controller + - #interrupt-cells: should be set to 1 + - #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. + + +Example: +++++++++ + +nwl_pcie: pcie@fd0e0000 { + #address-cells = <3>; + #size-cells = <2>; + compatible = "xlnx,nwl-pcie-2.11"; + #interrupt-cells = <1>; + msi-controller; + device_type = "pci"; + interrupt-parent = <&gic>; + interrupts = <0 114 4>, <0 115 4>, <0 116 4>, <0 117 4>, <0 118 4>; + interrupt-names = "msi0", "msi1", "intx", "dummy", "misc"; + interrupt-map-mask = <0x0 0x0 0x0 0x7>; + interrupt-map = <0x0 0x0 0x0 0x1 &pcie_intc 0x1>, + <0x0 0x0 0x0 0x2 &pcie_intc 0x2>, + <0x0 0x0 0x0 0x3 &pcie_intc 0x3>, + <0x0 0x0 0x0 0x4 &pcie_intc 0x4>; + + msi-parent = <&nwl_pcie>; + reg = <0x0 0xfd0e0000 0x0 0x1000>, + <0x0 0xfd480000 0x0 0x1000>, + <0x80 0x00000000 0x0 0x1000000>; + reg-names = "breg", "pcireg", "cfg"; + ranges = <0x02000000 0x00000000 0xe0000000 0x00000000 0xe0000000 0x00000000 0x10000000 /* non-prefetchable memory */ + 0x43000000 0x00000006 0x00000000 0x00000006 0x00000000 0x00000002 0x00000000>;/* prefetchable memory */ + + pcie_intc: legacy-interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + +}; diff --git a/Documentation/devicetree/bindings/pci/xilinx-pcie.txt b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt new file mode 100644 index 000000000..fd57a8118 --- /dev/null +++ b/Documentation/devicetree/bindings/pci/xilinx-pcie.txt @@ -0,0 +1,88 @@ +* Xilinx AXI PCIe Root Port Bridge DT description + +Required properties: +- #address-cells: Address representation for root ports, set to <3> +- #size-cells: Size representation for root ports, set to <2> +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. +- compatible: Should contain "xlnx,axi-pcie-host-1.00.a" +- reg: Should contain AXI PCIe registers location and length +- device_type: must be "pci" +- interrupts: Should contain AXI PCIe interrupt +- interrupt-map-mask, + interrupt-map: standard PCI properties to define the mapping of the + PCI interface to interrupt numbers. +- ranges: ranges for the PCI memory regions (I/O space region is not + supported by hardware) + Please refer to the standard PCI bus binding document for a more + detailed explanation + +Optional properties for Zynq/Microblaze: +- bus-range: PCI bus numbers covered + +Interrupt controller child node ++++++++++++++++++++++++++++++++ +Required properties: +- interrupt-controller: identifies the node as an interrupt controller +- #address-cells: specifies the number of cells needed to encode an + address. The value must be 0. +- #interrupt-cells: specifies the number of cells needed to encode an + interrupt source. The value must be 1. + +NOTE: +The core provides a single interrupt for both INTx/MSI messages. So, +created a interrupt controller node to support 'interrupt-map' DT +functionality. The driver will create an IRQ domain for this map, decode +the four INTx interrupts in ISR and route them to this domain. + + +Example: +++++++++ +Zynq: + pci_express: axi-pcie@50000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "xlnx,axi-pcie-host-1.00.a"; + reg = < 0x50000000 0x1000000 >; + device_type = "pci"; + interrupts = < 0 52 4 >; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + ranges = < 0x02000000 0 0x60000000 0x60000000 0 0x10000000 >; + + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + }; + + +Microblaze: + pci_express: axi-pcie@10000000 { + #address-cells = <3>; + #size-cells = <2>; + #interrupt-cells = <1>; + compatible = "xlnx,axi-pcie-host-1.00.a"; + reg = <0x10000000 0x4000000>; + device_type = "pci"; + interrupt-parent = <µblaze_0_intc>; + interrupts = <1 2>; + interrupt-map-mask = <0 0 0 7>; + interrupt-map = <0 0 0 1 &pcie_intc 1>, + <0 0 0 2 &pcie_intc 2>, + <0 0 0 3 &pcie_intc 3>, + <0 0 0 4 &pcie_intc 4>; + ranges = <0x02000000 0x00000000 0x80000000 0x80000000 0x00000000 0x10000000>; + + pcie_intc: interrupt-controller { + interrupt-controller; + #address-cells = <0>; + #interrupt-cells = <1>; + }; + + }; |