diff options
Diffstat (limited to 'Documentation/devicetree/bindings/phy')
175 files changed, 17709 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun4i-a10-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun4i-a10-usb-phy.yaml new file mode 100644 index 000000000..4fff091bd --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun4i-a10-usb-phy.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun4i-a10-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A10 USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 1 + + compatible: + enum: + - allwinner,sun4i-a10-usb-phy + - allwinner,sun7i-a20-usb-phy + + reg: + items: + - description: PHY Control registers + - description: PHY PMU1 registers + - description: PHY PMU2 registers + + reg-names: + items: + - const: phy_ctrl + - const: pmu1 + - const: pmu2 + + clocks: + maxItems: 1 + description: USB PHY bus clock + + clock-names: + const: usb_phy + + resets: + items: + - description: USB OTG reset + - description: USB Host 1 Controller reset + - description: USB Host 2 Controller reset + + reset-names: + items: + - const: usb0_reset + - const: usb1_reset + - const: usb2_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + + usb1_vbus-supply: + description: Regulator controlling USB1 Host controller + + usb2_vbus-supply: + description: Regulator controlling USB2 Host controller + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/sun4i-a10-ccu.h> + #include <dt-bindings/reset/sun4i-a10-ccu.h> + + usbphy: phy@1c13400 { + #phy-cells = <1>; + compatible = "allwinner,sun4i-a10-usb-phy"; + reg = <0x01c13400 0x10>, <0x01c14800 0x4>, <0x01c1c800 0x4>; + reg-names = "phy_ctrl", "pmu1", "pmu2"; + clocks = <&ccu CLK_USB_PHY>; + clock-names = "usb_phy"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY1>, + <&ccu RST_USB_PHY2>; + reset-names = "usb0_reset", "usb1_reset", "usb2_reset"; + usb0_id_det-gpios = <&pio 7 19 GPIO_ACTIVE_HIGH>; + usb0_vbus_det-gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun50i-a64-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun50i-a64-usb-phy.yaml new file mode 100644 index 000000000..f557feca9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun50i-a64-usb-phy.yaml @@ -0,0 +1,110 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun50i-a64-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A64 USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 1 + + compatible: + enum: + - allwinner,sun20i-d1-usb-phy + - allwinner,sun50i-a64-usb-phy + + reg: + items: + - description: PHY Control registers + - description: PHY PMU0 registers + - description: PHY PMU1 registers + + reg-names: + items: + - const: phy_ctrl + - const: pmu0 + - const: pmu1 + + clocks: + items: + - description: USB OTG PHY bus clock + - description: USB Host 0 PHY bus clock + + clock-names: + items: + - const: usb0_phy + - const: usb1_phy + + resets: + items: + - description: USB OTG reset + - description: USB Host 1 Controller reset + + reset-names: + items: + - const: usb0_reset + - const: usb1_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + + usb1_vbus-supply: + description: Regulator controlling USB1 Host controller + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/sun50i-a64-ccu.h> + #include <dt-bindings/reset/sun50i-a64-ccu.h> + + phy@1c19400 { + #phy-cells = <1>; + compatible = "allwinner,sun50i-a64-usb-phy"; + reg = <0x01c19400 0x14>, + <0x01c1a800 0x4>, + <0x01c1b800 0x4>; + reg-names = "phy_ctrl", + "pmu0", + "pmu1"; + clocks = <&ccu CLK_USB_PHY0>, + <&ccu CLK_USB_PHY1>; + clock-names = "usb0_phy", + "usb1_phy"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY1>; + reset-names = "usb0_reset", + "usb1_reset"; + usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus-supply = <®_usb1_vbus>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb-phy.yaml new file mode 100644 index 000000000..4480fdedd --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb-phy.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun50i-h6-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner H6 USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 1 + + compatible: + const: allwinner,sun50i-h6-usb-phy + + reg: + items: + - description: PHY Control registers + - description: PHY PMU0 registers + - description: PHY PMU3 registers + + reg-names: + items: + - const: phy_ctrl + - const: pmu0 + - const: pmu3 + + clocks: + items: + - description: USB OTG PHY bus clock + - description: USB Host PHY bus clock + + clock-names: + items: + - const: usb0_phy + - const: usb3_phy + + resets: + items: + - description: USB OTG reset + - description: USB Host Controller reset + + reset-names: + items: + - const: usb0_reset + - const: usb3_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + + usb3_vbus-supply: + description: Regulator controlling USB3 Host controller + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/sun50i-h6-ccu.h> + #include <dt-bindings/reset/sun50i-h6-ccu.h> + + phy@5100400 { + #phy-cells = <1>; + compatible = "allwinner,sun50i-h6-usb-phy"; + reg = <0x05100400 0x24>, + <0x05101800 0x4>, + <0x05311800 0x4>; + reg-names = "phy_ctrl", + "pmu0", + "pmu3"; + clocks = <&ccu CLK_USB_PHY0>, + <&ccu CLK_USB_PHY3>; + clock-names = "usb0_phy", + "usb3_phy"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY3>; + reset-names = "usb0_reset", + "usb3_reset"; + usb0_id_det-gpios = <&pio 2 6 GPIO_ACTIVE_HIGH>; /* PC6 */ + usb0_vbus-supply = <®_vcc5v>; + usb3_vbus-supply = <®_vcc5v>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb3-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb3-phy.yaml new file mode 100644 index 000000000..cf4eed230 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun50i-h6-usb3-phy.yaml @@ -0,0 +1,49 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 Ondrej Jirman <megous@megous.com> +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun50i-h6-usb3-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner H6 USB3 PHY + +maintainers: + - Ondrej Jirman <megous@megous.com> + +properties: + compatible: + enum: + - allwinner,sun50i-h6-usb3-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - clocks + - resets + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/sun50i-h6-ccu.h> + #include <dt-bindings/reset/sun50i-h6-ccu.h> + phy@5210000 { + compatible = "allwinner,sun50i-h6-usb3-phy"; + reg = <0x5210000 0x10000>; + clocks = <&ccu CLK_USB_PHY1>; + resets = <&ccu RST_USB_PHY1>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun5i-a13-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun5i-a13-usb-phy.yaml new file mode 100644 index 000000000..1563e3df3 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun5i-a13-usb-phy.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun5i-a13-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A13 USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 1 + + compatible: + const: allwinner,sun5i-a13-usb-phy + + reg: + items: + - description: PHY Control registers + - description: PHY PMU1 registers + + reg-names: + items: + - const: phy_ctrl + - const: pmu1 + + clocks: + maxItems: 1 + description: USB OTG PHY bus clock + + clock-names: + const: usb_phy + + resets: + items: + - description: USB OTG reset + - description: USB Host 1 Controller reset + + reset-names: + items: + - const: usb0_reset + - const: usb1_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + + usb1_vbus-supply: + description: Regulator controlling USB1 Host controller + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/sun5i-ccu.h> + #include <dt-bindings/reset/sun5i-ccu.h> + + phy@1c13400 { + #phy-cells = <1>; + compatible = "allwinner,sun5i-a13-usb-phy"; + reg = <0x01c13400 0x10>, <0x01c14800 0x4>; + reg-names = "phy_ctrl", "pmu1"; + clocks = <&ccu CLK_USB_PHY0>; + clock-names = "usb_phy"; + resets = <&ccu RST_USB_PHY0>, <&ccu RST_USB_PHY1>; + reset-names = "usb0_reset", "usb1_reset"; + usb0_id_det-gpios = <&pio 6 2 (GPIO_ACTIVE_HIGH | GPIO_PULL_UP)>; /* PG2 */ + usb0_vbus_det-gpios = <&pio 6 1 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; /* PG1 */ + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_usb1_vbus>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun6i-a31-mipi-dphy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun6i-a31-mipi-dphy.yaml new file mode 100644 index 000000000..6a4fd4929 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun6i-a31-mipi-dphy.yaml @@ -0,0 +1,84 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun6i-a31-mipi-dphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 MIPI D-PHY Controller + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 0 + + compatible: + oneOf: + - const: allwinner,sun6i-a31-mipi-dphy + - const: allwinner,sun50i-a100-mipi-dphy + - items: + - const: allwinner,sun50i-a64-mipi-dphy + - const: allwinner,sun6i-a31-mipi-dphy + - items: + - const: allwinner,sun20i-d1-mipi-dphy + - const: allwinner,sun50i-a100-mipi-dphy + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + items: + - description: Bus Clock + - description: Module Clock + + clock-names: + items: + - const: bus + - const: mod + + resets: + maxItems: 1 + + allwinner,direction: + $ref: /schemas/types.yaml#/definitions/string + description: | + Direction of the D-PHY: + - "rx" for receiving (e.g. when used with MIPI CSI-2); + - "tx" for transmitting (e.g. when used with MIPI DSI). + + enum: + - tx + - rx + default: tx + +required: + - "#phy-cells" + - compatible + - reg + - interrupts + - clocks + - clock-names + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + dphy0: d-phy@1ca1000 { + compatible = "allwinner,sun6i-a31-mipi-dphy"; + reg = <0x01ca1000 0x1000>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu 23>, <&ccu 97>; + clock-names = "bus", "mod"; + resets = <&ccu 4>; + #phy-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun6i-a31-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun6i-a31-usb-phy.yaml new file mode 100644 index 000000000..4897a3d2f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun6i-a31-usb-phy.yaml @@ -0,0 +1,121 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun6i-a31-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A31 USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 1 + + compatible: + const: allwinner,sun6i-a31-usb-phy + + reg: + items: + - description: PHY Control registers + - description: PHY PMU1 registers + - description: PHY PMU2 registers + + reg-names: + items: + - const: phy_ctrl + - const: pmu1 + - const: pmu2 + + clocks: + items: + - description: USB OTG PHY bus clock + - description: USB Host 0 PHY bus clock + - description: USB Host 1 PHY bus clock + + clock-names: + items: + - const: usb0_phy + - const: usb1_phy + - const: usb2_phy + + resets: + items: + - description: USB OTG reset + - description: USB Host 1 Controller reset + - description: USB Host 2 Controller reset + + reset-names: + items: + - const: usb0_reset + - const: usb1_reset + - const: usb2_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + + usb1_vbus-supply: + description: Regulator controlling USB1 Host controller + + usb2_vbus-supply: + description: Regulator controlling USB2 Host controller + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/sun6i-a31-ccu.h> + #include <dt-bindings/reset/sun6i-a31-ccu.h> + + phy@1c19400 { + #phy-cells = <1>; + compatible = "allwinner,sun6i-a31-usb-phy"; + reg = <0x01c19400 0x10>, + <0x01c1a800 0x4>, + <0x01c1b800 0x4>; + reg-names = "phy_ctrl", + "pmu1", + "pmu2"; + clocks = <&ccu CLK_USB_PHY0>, + <&ccu CLK_USB_PHY1>, + <&ccu CLK_USB_PHY2>; + clock-names = "usb0_phy", + "usb1_phy", + "usb2_phy"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY1>, + <&ccu RST_USB_PHY2>; + reset-names = "usb0_reset", + "usb1_reset", + "usb2_reset"; + usb0_id_det-gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>; /* PA15 */ + usb0_vbus_det-gpios = <&pio 0 16 GPIO_ACTIVE_HIGH>; /* PA16 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun8i-a23-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun8i-a23-usb-phy.yaml new file mode 100644 index 000000000..99de9c688 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun8i-a23-usb-phy.yaml @@ -0,0 +1,104 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun8i-a23-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A23 USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 1 + + compatible: + enum: + - allwinner,sun8i-a23-usb-phy + - allwinner,sun8i-a33-usb-phy + + reg: + items: + - description: PHY Control registers + - description: PHY PMU1 registers + + reg-names: + items: + - const: phy_ctrl + - const: pmu1 + + clocks: + items: + - description: USB OTG PHY bus clock + - description: USB Host 0 PHY bus clock + + clock-names: + items: + - const: usb0_phy + - const: usb1_phy + + resets: + items: + - description: USB OTG reset + - description: USB Host 1 Controller reset + + reset-names: + items: + - const: usb0_reset + - const: usb1_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + + usb1_vbus-supply: + description: Regulator controlling USB1 Host controller + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/sun8i-a23-a33-ccu.h> + #include <dt-bindings/reset/sun8i-a23-a33-ccu.h> + + phy@1c19400 { + #phy-cells = <1>; + compatible = "allwinner,sun8i-a23-usb-phy"; + reg = <0x01c19400 0x10>, <0x01c1a800 0x4>; + reg-names = "phy_ctrl", "pmu1"; + clocks = <&ccu CLK_USB_PHY0>, + <&ccu CLK_USB_PHY1>; + clock-names = "usb0_phy", + "usb1_phy"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY1>; + reset-names = "usb0_reset", + "usb1_reset"; + usb0_id_det-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus-supply = <®_usb1_vbus>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun8i-a83t-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun8i-a83t-usb-phy.yaml new file mode 100644 index 000000000..73438d84d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun8i-a83t-usb-phy.yaml @@ -0,0 +1,124 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun8i-a83t-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A83t USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 1 + + compatible: + const: allwinner,sun8i-a83t-usb-phy + + reg: + items: + - description: PHY Control registers + - description: PHY PMU1 registers + - description: PHY PMU2 registers + + reg-names: + items: + - const: phy_ctrl + - const: pmu1 + - const: pmu2 + + clocks: + items: + - description: USB OTG PHY bus clock + - description: USB Host 0 PHY bus clock + - description: USB Host 1 PHY bus clock + - description: USB HSIC 12MHz clock + + clock-names: + items: + - const: usb0_phy + - const: usb1_phy + - const: usb2_phy + - const: usb2_hsic_12M + + resets: + items: + - description: USB OTG reset + - description: USB Host 1 Controller reset + - description: USB Host 2 Controller reset + + reset-names: + items: + - const: usb0_reset + - const: usb1_reset + - const: usb2_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + + usb1_vbus-supply: + description: Regulator controlling USB1 Host controller + + usb2_vbus-supply: + description: Regulator controlling USB2 Host controller + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/sun8i-a83t-ccu.h> + #include <dt-bindings/reset/sun8i-a83t-ccu.h> + + phy@1c19400 { + #phy-cells = <1>; + compatible = "allwinner,sun8i-a83t-usb-phy"; + reg = <0x01c19400 0x10>, + <0x01c1a800 0x14>, + <0x01c1b800 0x14>; + reg-names = "phy_ctrl", + "pmu1", + "pmu2"; + clocks = <&ccu CLK_USB_PHY0>, + <&ccu CLK_USB_PHY1>, + <&ccu CLK_USB_HSIC>, + <&ccu CLK_USB_HSIC_12M>; + clock-names = "usb0_phy", + "usb1_phy", + "usb2_phy", + "usb2_hsic_12M"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY1>, + <&ccu RST_USB_HSIC>; + reset-names = "usb0_reset", + "usb1_reset", + "usb2_reset"; + usb0_id_det-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */ + usb0_vbus_power-supply = <&usb_power_supply>; + usb0_vbus-supply = <®_drivevbus>; + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun8i-h3-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun8i-h3-usb-phy.yaml new file mode 100644 index 000000000..2df012d13 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun8i-h3-usb-phy.yaml @@ -0,0 +1,167 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun8i-h3-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner H3 USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 1 + + compatible: + enum: + - allwinner,sun8i-h3-usb-phy + - allwinner,sun50i-h616-usb-phy + + reg: + items: + - description: PHY Control registers + - description: PHY PMU0 registers + - description: PHY PMU1 registers + - description: PHY PMU2 registers + - description: PHY PMU3 registers + + reg-names: + items: + - const: phy_ctrl + - const: pmu0 + - const: pmu1 + - const: pmu2 + - const: pmu3 + + clocks: + minItems: 4 + items: + - description: USB OTG PHY bus clock + - description: USB Host 0 PHY bus clock + - description: USB Host 1 PHY bus clock + - description: USB Host 2 PHY bus clock + - description: PMU clock for host port 2 + + clock-names: + minItems: 4 + items: + - const: usb0_phy + - const: usb1_phy + - const: usb2_phy + - const: usb3_phy + - const: pmu2_clk + + resets: + items: + - description: USB OTG reset + - description: USB Host 1 Controller reset + - description: USB Host 2 Controller reset + - description: USB Host 3 Controller reset + + reset-names: + items: + - const: usb0_reset + - const: usb1_reset + - const: usb2_reset + - const: usb3_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + + usb1_vbus-supply: + description: Regulator controlling USB1 Host controller + + usb2_vbus-supply: + description: Regulator controlling USB2 Host controller + + usb3_vbus-supply: + description: Regulator controlling USB3 Host controller + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +allOf: + - if: + properties: + compatible: + contains: + enum: + - allwinner,sun50i-h616-usb-phy + then: + properties: + clocks: + minItems: 5 + + clock-names: + minItems: 5 + else: + properties: + clocks: + maxItems: 4 + + clock-names: + maxItems: 4 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/sun8i-h3-ccu.h> + #include <dt-bindings/reset/sun8i-h3-ccu.h> + + phy@1c19400 { + #phy-cells = <1>; + compatible = "allwinner,sun8i-h3-usb-phy"; + reg = <0x01c19400 0x2c>, + <0x01c1a800 0x4>, + <0x01c1b800 0x4>, + <0x01c1c800 0x4>, + <0x01c1d800 0x4>; + reg-names = "phy_ctrl", + "pmu0", + "pmu1", + "pmu2", + "pmu3"; + clocks = <&ccu CLK_USB_PHY0>, + <&ccu CLK_USB_PHY1>, + <&ccu CLK_USB_PHY2>, + <&ccu CLK_USB_PHY3>; + clock-names = "usb0_phy", + "usb1_phy", + "usb2_phy", + "usb3_phy"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY1>, + <&ccu RST_USB_PHY2>, + <&ccu RST_USB_PHY3>; + reset-names = "usb0_reset", + "usb1_reset", + "usb2_reset", + "usb3_reset"; + usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ + usb0_vbus-supply = <®_usb0_vbus>; + usb1_vbus-supply = <®_usb1_vbus>; + usb2_vbus-supply = <®_usb2_vbus>; + usb3_vbus-supply = <®_usb3_vbus>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun8i-r40-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun8i-r40-usb-phy.yaml new file mode 100644 index 000000000..2dd31630c --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun8i-r40-usb-phy.yaml @@ -0,0 +1,121 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun8i-r40-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner R40 USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 1 + + compatible: + const: allwinner,sun8i-r40-usb-phy + + reg: + items: + - description: PHY Control registers + - description: PHY PMU0 registers + - description: PHY PMU1 registers + - description: PHY PMU2 registers + + reg-names: + items: + - const: phy_ctrl + - const: pmu0 + - const: pmu1 + - const: pmu2 + + clocks: + items: + - description: USB OTG PHY bus clock + - description: USB Host 0 PHY bus clock + - description: USB Host 1 PHY bus clock + + clock-names: + items: + - const: usb0_phy + - const: usb1_phy + - const: usb2_phy + + resets: + items: + - description: USB OTG reset + - description: USB Host 1 Controller reset + - description: USB Host 2 Controller reset + + reset-names: + items: + - const: usb0_reset + - const: usb1_reset + - const: usb2_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + + usb1_vbus-supply: + description: Regulator controlling USB1 Host controller + + usb2_vbus-supply: + description: Regulator controlling USB2 Host controller + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/sun8i-r40-ccu.h> + #include <dt-bindings/reset/sun8i-r40-ccu.h> + + phy@1c13400 { + #phy-cells = <1>; + compatible = "allwinner,sun8i-r40-usb-phy"; + reg = <0x01c13400 0x14>, + <0x01c14800 0x4>, + <0x01c19800 0x4>, + <0x01c1c800 0x4>; + reg-names = "phy_ctrl", + "pmu0", + "pmu1", + "pmu2"; + clocks = <&ccu CLK_USB_PHY0>, + <&ccu CLK_USB_PHY1>, + <&ccu CLK_USB_PHY2>; + clock-names = "usb0_phy", + "usb1_phy", + "usb2_phy"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY1>, + <&ccu RST_USB_PHY2>; + reset-names = "usb0_reset", + "usb1_reset", + "usb2_reset"; + usb1_vbus-supply = <®_vcc5v0>; + usb2_vbus-supply = <®_vcc5v0>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun8i-v3s-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun8i-v3s-usb-phy.yaml new file mode 100644 index 000000000..395d33855 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun8i-v3s-usb-phy.yaml @@ -0,0 +1,88 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun8i-v3s-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner V3s USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 1 + + compatible: + const: allwinner,sun8i-v3s-usb-phy + + reg: + items: + - description: PHY Control registers + - description: PHY PMU0 registers + + reg-names: + items: + - const: phy_ctrl + - const: pmu0 + + clocks: + maxItems: 1 + description: USB OTG PHY bus clock + + clock-names: + const: usb0_phy + + resets: + maxItems: 1 + description: USB OTG reset + + reset-names: + const: usb0_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/sun8i-v3s-ccu.h> + #include <dt-bindings/reset/sun8i-v3s-ccu.h> + + phy@1c19400 { + #phy-cells = <1>; + compatible = "allwinner,sun8i-v3s-usb-phy"; + reg = <0x01c19400 0x2c>, + <0x01c1a800 0x4>; + reg-names = "phy_ctrl", + "pmu0"; + clocks = <&ccu CLK_USB_PHY0>; + clock-names = "usb0_phy"; + resets = <&ccu RST_USB_PHY0>; + reset-names = "usb0_reset"; + usb0_id_det-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun9i-a80-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun9i-a80-usb-phy.yaml new file mode 100644 index 000000000..bd9445f6f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,sun9i-a80-usb-phy.yaml @@ -0,0 +1,132 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,sun9i-a80-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner A80 USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 0 + + compatible: + const: allwinner,sun9i-a80-usb-phy + + reg: + maxItems: 1 + + clocks: + anyOf: + - maxItems: 1 + description: Main PHY Clock + + - items: + - description: Main PHY clock + - description: HSIC 12MHz clock + - description: HSIC 480MHz clock + + clock-names: + oneOf: + - const: phy + + - items: + - const: phy + - const: hsic_12M + - const: hsic_480M + + resets: + minItems: 1 + items: + - description: Normal USB PHY reset + - description: HSIC Reset + + reset-names: + minItems: 1 + items: + - const: phy + - const: hsic + + phy_type: + const: hsic + description: + When absent, the PHY type will be assumed to be normal USB. + + phy-supply: + description: + Regulator that powers VBUS + +required: + - "#phy-cells" + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + +additionalProperties: false + +if: + properties: + phy_type: + const: hsic + + required: + - phy_type + +then: + properties: + clocks: + maxItems: 3 + + clock-names: + maxItems: 3 + + resets: + maxItems: 2 + + reset-names: + maxItems: 2 + +examples: + - | + #include <dt-bindings/clock/sun9i-a80-usb.h> + #include <dt-bindings/reset/sun9i-a80-usb.h> + + usbphy1: phy@a00800 { + compatible = "allwinner,sun9i-a80-usb-phy"; + reg = <0x00a00800 0x4>; + clocks = <&usb_clocks CLK_USB0_PHY>; + clock-names = "phy"; + resets = <&usb_clocks RST_USB0_PHY>; + reset-names = "phy"; + phy-supply = <®_usb1_vbus>; + #phy-cells = <0>; + }; + + - | + #include <dt-bindings/clock/sun9i-a80-usb.h> + #include <dt-bindings/reset/sun9i-a80-usb.h> + + usbphy3: phy@a02800 { + compatible = "allwinner,sun9i-a80-usb-phy"; + reg = <0x00a02800 0x4>; + clocks = <&usb_clocks CLK_USB2_PHY>, + <&usb_clocks CLK_USB_HSIC>, + <&usb_clocks CLK_USB2_HSIC>; + clock-names = "phy", + "hsic_12M", + "hsic_480M"; + resets = <&usb_clocks RST_USB2_PHY>, + <&usb_clocks RST_USB2_HSIC>; + reset-names = "phy", + "hsic"; + phy_type = "hsic"; + phy-supply = <®_usb3_vbus>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-phy.yaml new file mode 100644 index 000000000..948839499 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/allwinner,suniv-f1c100s-usb-phy.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/allwinner,suniv-f1c100s-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Allwinner F1C100s USB PHY + +maintainers: + - Chen-Yu Tsai <wens@csie.org> + - Maxime Ripard <mripard@kernel.org> + +properties: + "#phy-cells": + const: 1 + + compatible: + const: allwinner,suniv-f1c100s-usb-phy + + reg: + maxItems: 1 + description: PHY Control registers + + reg-names: + const: phy_ctrl + + clocks: + maxItems: 1 + description: USB OTG PHY bus clock + + clock-names: + const: usb0_phy + + resets: + maxItems: 1 + description: USB OTG reset + + reset-names: + const: usb0_reset + + usb0_id_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG ID pin + + usb0_vbus_det-gpios: + maxItems: 1 + description: GPIO to the USB OTG VBUS detect pin + + usb0_vbus_power-supply: + description: Power supply to detect the USB OTG VBUS + + usb0_vbus-supply: + description: Regulator controlling USB OTG VBUS + +required: + - "#phy-cells" + - compatible + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + #include <dt-bindings/clock/suniv-ccu-f1c100s.h> + #include <dt-bindings/reset/suniv-ccu-f1c100s.h> + + phy@1c13400 { + compatible = "allwinner,suniv-f1c100s-usb-phy"; + reg = <0x01c13400 0x10>; + reg-names = "phy_ctrl"; + clocks = <&ccu CLK_USB_PHY0>; + clock-names = "usb0_phy"; + resets = <&ccu RST_USB_PHY0>; + reset-names = "usb0_reset"; + #phy-cells = <1>; + usb0_id_det-gpios = <&pio 4 2 GPIO_ACTIVE_HIGH>; + }; diff --git a/Documentation/devicetree/bindings/phy/amlogic,axg-mipi-dphy.yaml b/Documentation/devicetree/bindings/phy/amlogic,axg-mipi-dphy.yaml new file mode 100644 index 000000000..64795f170 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,axg-mipi-dphy.yaml @@ -0,0 +1,70 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2020 BayLibre, SAS +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/amlogic,axg-mipi-dphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic AXG MIPI D-PHY + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +properties: + compatible: + enum: + - amlogic,axg-mipi-dphy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: pclk + + resets: + maxItems: 1 + + reset-names: + items: + - const: phy + + "#phy-cells": + const: 0 + + phys: + maxItems: 1 + + phy-names: + items: + - const: analog + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - phys + - phy-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + phy@ff640000 { + compatible = "amlogic,axg-mipi-dphy"; + reg = <0xff640000 0x100>; + clocks = <&clk_mipi_dsi_phy>; + clock-names = "pclk"; + resets = <&reset_phy>; + reset-names = "phy"; + phys = <&mipi_pcie_analog_dphy>; + phy-names = "analog"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/amlogic,g12a-mipi-dphy-analog.yaml b/Documentation/devicetree/bindings/phy/amlogic,g12a-mipi-dphy-analog.yaml new file mode 100644 index 000000000..c8c83acfb --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,g12a-mipi-dphy-analog.yaml @@ -0,0 +1,35 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/amlogic,g12a-mipi-dphy-analog.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic G12A MIPI analog PHY + +maintainers: + - Neil Armstrong <narmstrong@baylibre.com> + +properties: + compatible: + const: amlogic,g12a-mipi-dphy-analog + + "#phy-cells": + const: 0 + + reg: + maxItems: 1 + +required: + - compatible + - reg + - "#phy-cells" + +additionalProperties: false + +examples: + - | + phy@0 { + compatible = "amlogic,g12a-mipi-dphy-analog"; + reg = <0x0 0xc>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/amlogic,g12a-usb2-phy.yaml b/Documentation/devicetree/bindings/phy/amlogic,g12a-usb2-phy.yaml new file mode 100644 index 000000000..0031fb6a4 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,g12a-usb2-phy.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/amlogic,g12a-usb2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic G12A USB2 PHY + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +properties: + compatible: + enum: + - amlogic,g12a-usb2-phy + - amlogic,a1-usb2-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: xtal + + resets: + maxItems: 1 + + reset-names: + items: + - const: phy + + "#phy-cells": + const: 0 + + phy-supply: + description: + Phandle to a regulator that provides power to the PHY. This + regulator will be managed during the PHY power on/off sequence. + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - "#phy-cells" + +if: + properties: + compatible: + enum: + - amlogic,meson-a1-usb-ctrl + +then: + properties: + power-domains: + maxItems: 1 + required: + - power-domains + +additionalProperties: false + +examples: + - | + phy@36000 { + compatible = "amlogic,g12a-usb2-phy"; + reg = <0x36000 0x2000>; + clocks = <&xtal>; + clock-names = "xtal"; + resets = <&phy_reset>; + reset-names = "phy"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/amlogic,g12a-usb3-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/amlogic,g12a-usb3-pcie-phy.yaml new file mode 100644 index 000000000..1a5a12adb --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,g12a-usb3-pcie-phy.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2019 BayLibre, SAS +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/amlogic,g12a-usb3-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic G12A USB3 + PCIE Combo PHY + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +properties: + compatible: + enum: + - amlogic,g12a-usb3-pcie-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: ref_clk + + resets: + maxItems: 1 + + reset-names: + items: + - const: phy + + "#phy-cells": + const: 1 + + phy-supply: + description: + Phandle to a regulator that provides power to the PHY. This + regulator will be managed during the PHY power on/off sequence. + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + phy@46000 { + compatible = "amlogic,g12a-usb3-pcie-phy"; + reg = <0x46000 0x2000>; + clocks = <&ref_clk>; + clock-names = "ref_clk"; + resets = <&phy_reset>; + reset-names = "phy"; + #phy-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml b/Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml new file mode 100644 index 000000000..009a39808 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-axg-mipi-pcie-analog.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/amlogic,meson-axg-mipi-pcie-analog.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic AXG shared MIPI/PCIE analog PHY + +maintainers: + - Remi Pommarel <repk@triplefau.lt> + +description: |+ + The Everything-Else Power Domains node should be the child of a syscon + node with the required property: + + - compatible: Should be the following: + "amlogic,meson-gx-hhi-sysctrl", "simple-mfd", "syscon" + + Refer to the bindings described in + Documentation/devicetree/bindings/mfd/syscon.yaml + +properties: + compatible: + const: amlogic,axg-mipi-pcie-analog-phy + + "#phy-cells": + const: 0 + +required: + - compatible + - "#phy-cells" + +additionalProperties: false + +examples: + - | + mpphy: phy { + compatible = "amlogic,axg-mipi-pcie-analog-phy"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-axg-pcie.yaml b/Documentation/devicetree/bindings/phy/amlogic,meson-axg-pcie.yaml new file mode 100644 index 000000000..40fbf8ac3 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-axg-pcie.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/amlogic,meson-axg-pcie.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic AXG PCIE PHY + +maintainers: + - Remi Pommarel <repk@triplefau.lt> + +properties: + compatible: + const: amlogic,axg-pcie-phy + + reg: + maxItems: 1 + + resets: + maxItems: 1 + + phys: + maxItems: 1 + + phy-names: + const: analog + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - phys + - phy-names + - resets + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/reset/amlogic,meson-axg-reset.h> + #include <dt-bindings/phy/phy.h> + pcie_phy: pcie-phy@ff644000 { + compatible = "amlogic,axg-pcie-phy"; + reg = <0xff644000 0x1c>; + resets = <&reset RESET_PCIE_PHY>; + phys = <&mipi_analog_phy PHY_TYPE_PCIE>; + phy-names = "analog"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-gxl-usb2-phy.yaml b/Documentation/devicetree/bindings/phy/amlogic,meson-gxl-usb2-phy.yaml new file mode 100644 index 000000000..c2f5c9d2f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-gxl-usb2-phy.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/amlogic,meson-gxl-usb2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson GXL USB2 PHY + +maintainers: + - Neil Armstrong <neil.armstrong@linaro.org> + +properties: + compatible: + const: amlogic,meson-gxl-usb2-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: phy + + resets: + maxItems: 1 + + reset-names: + items: + - const: phy + + "#phy-cells": + const: 0 + + phy-supply: true + +required: + - compatible + - reg + - "#phy-cells" + +additionalProperties: false + +examples: + - | + phy@78000 { + compatible = "amlogic,meson-gxl-usb2-phy"; + reg = <0x78000 0x20>; + clocks = <&xtal>; + clock-names = "phy"; + resets = <&phy_reset>; + reset-names = "phy"; + #phy-cells = <0>; + phy-supply = <&usb2_supply>; + }; diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson8-hdmi-tx-phy.yaml b/Documentation/devicetree/bindings/phy/amlogic,meson8-hdmi-tx-phy.yaml new file mode 100644 index 000000000..6f9fd1c95 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,meson8-hdmi-tx-phy.yaml @@ -0,0 +1,65 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/amlogic,meson8-hdmi-tx-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson8, Meson8b and Meson8m2 HDMI TX PHY + +maintainers: + - Martin Blumenstingl <martin.blumenstingl@googlemail.com> + +description: |+ + The HDMI TX PHY node should be the child of a syscon node with the + required property: + + compatible = "amlogic,meson-hhi-sysctrl", "simple-mfd", "syscon" + + Refer to the bindings described in + Documentation/devicetree/bindings/mfd/syscon.yaml + +properties: + $nodename: + pattern: "^hdmi-phy@[0-9a-f]+$" + + compatible: + oneOf: + - items: + - enum: + - amlogic,meson8b-hdmi-tx-phy + - amlogic,meson8m2-hdmi-tx-phy + - const: amlogic,meson8-hdmi-tx-phy + - const: amlogic,meson8-hdmi-tx-phy + + reg: + maxItems: 1 + + clocks: + minItems: 1 + description: + HDMI TMDS clock + + "#phy-cells": + const: 0 + +required: + - compatible + - "#phy-cells" + +additionalProperties: false + +examples: + - | + hdmi-phy@3a0 { + compatible = "amlogic,meson8-hdmi-tx-phy"; + reg = <0x3a0 0xc>; + clocks = <&tmds_clock>; + #phy-cells = <0>; + }; + - | + hdmi-phy@3a0 { + compatible = "amlogic,meson8b-hdmi-tx-phy", "amlogic,meson8-hdmi-tx-phy"; + reg = <0x3a0 0xc>; + clocks = <&tmds_clock>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson8b-usb2-phy.yaml b/Documentation/devicetree/bindings/phy/amlogic,meson8b-usb2-phy.yaml new file mode 100644 index 000000000..df68bfe5f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/amlogic,meson8b-usb2-phy.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/amlogic,meson8b-usb2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Amlogic Meson8, Meson8b, Meson8m2 and GXBB USB2 PHY + +maintainers: + - Martin Blumenstingl <martin.blumenstingl@googlemail.com> + +properties: + compatible: + oneOf: + - items: + - enum: + - amlogic,meson8-usb2-phy + - amlogic,meson8b-usb2-phy + - amlogic,meson8m2-usb2-phy + - const: amlogic,meson-mx-usb2-phy + - const: amlogic,meson-gxbb-usb2-phy + + reg: + maxItems: 1 + + clocks: + minItems: 2 + + clock-names: + items: + - const: usb_general + - const: usb + + resets: + minItems: 1 + + "#phy-cells": + const: 0 + + phy-supply: + description: + Phandle to a regulator that provides power to the PHY. This + regulator will be managed during the PHY power on/off sequence. + +required: + - compatible + - reg + - clocks + - clock-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + usb-phy@c0000000 { + compatible = "amlogic,meson-gxbb-usb2-phy"; + reg = <0xc0000000 0x20>; + resets = <&reset_usb_phy>; + clocks = <&clk_usb_general>, <&reset_usb>; + clock-names = "usb_general", "usb"; + phy-supply = <&usb_vbus>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt b/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt new file mode 100644 index 000000000..e1bb12711 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/apm-xgene-phy.txt @@ -0,0 +1,76 @@ +* APM X-Gene 15Gbps Multi-purpose PHY nodes + +PHY nodes are defined to describe on-chip 15Gbps Multi-purpose PHY. Each +PHY (pair of lanes) has its own node. + +Required properties: +- compatible : Shall be "apm,xgene-phy". +- reg : PHY memory resource is the SDS PHY access resource. +- #phy-cells : Shall be 1 as it expects one argument for setting + the mode of the PHY. Possible values are 0 (SATA), + 1 (SGMII), 2 (PCIe), 3 (USB), and 4 (XFI). + +Optional properties: +- status : Shall be "ok" if enabled or "disabled" if disabled. + Default is "ok". +- clocks : Reference to the clock entry. +- apm,tx-eye-tuning : Manual control to fine tune the capture of the serial + bit lines from the automatic calibrated position. + Two set of 3-tuple setting for each (up to 3) + supported link speed on the host. Range from 0 to + 127 in unit of one bit period. Default is 10. +- apm,tx-eye-direction : Eye tuning manual control direction. 0 means sample + data earlier than the nominal sampling point. 1 means + sample data later than the nominal sampling point. + Two set of 3-tuple setting for each (up to 3) + supported link speed on the host. Default is 0. +- apm,tx-boost-gain : Frequency boost AC (LSB 3-bit) and DC (2-bit) + gain control. Two set of 3-tuple setting for each + (up to 3) supported link speed on the host. Range is + between 0 to 31 in unit of dB. Default is 3. +- apm,tx-amplitude : Amplitude control. Two set of 3-tuple setting for + each (up to 3) supported link speed on the host. + Range is between 0 to 199500 in unit of uV. + Default is 199500 uV. +- apm,tx-pre-cursor1 : 1st pre-cursor emphasis taps control. Two set of + 3-tuple setting for each (up to 3) supported link + speed on the host. Range is 0 to 273000 in unit of + uV. Default is 0. +- apm,tx-pre-cursor2 : 2st pre-cursor emphasis taps control. Two set of + 3-tuple setting for each (up to 3) supported link + speed on the host. Range is 0 to 127400 in unit uV. + Default is 0x0. +- apm,tx-post-cursor : Post-cursor emphasis taps control. Two set of + 3-tuple setting for Gen1, Gen2, and Gen3. Range is + between 0 to 0x1f in unit of 18.2mV. Default is 0xf. +- apm,tx-speed : Tx operating speed. One set of 3-tuple for each + supported link speed on the host. + 0 = 1-2Gbps + 1 = 2-4Gbps (1st tuple default) + 2 = 4-8Gbps + 3 = 8-15Gbps (2nd tuple default) + 4 = 2.5-4Gbps + 5 = 4-5Gbps + 6 = 5-6Gbps + 7 = 6-16Gbps (3rd tuple default) + +NOTE: PHY override parameters are board specific setting. + +Example: + phy1: phy@1f21a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f21a000 0x0 0x100>; + #phy-cells = <1>; + }; + + phy2: phy@1f22a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f22a000 0x0 0x100>; + #phy-cells = <1>; + }; + + phy3: phy@1f23a000 { + compatible = "apm,xgene-phy"; + reg = <0x0 0x1f23a000 0x0 0x100>; + #phy-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.yaml b/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.yaml new file mode 100644 index 000000000..426101530 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/bcm-ns-usb2-phy.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/bcm-ns-usb2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom Northstar USB 2.0 PHY + +description: > + To initialize USB 2.0 PHY driver needs to setup PLL correctly. + To do this it requires passing phandle to the USB PHY reference clock. + +maintainers: + - RafaĆ MiĆecki <rafal@milecki.pl> + +properties: + compatible: + const: brcm,ns-usb2-phy + + reg: + anyOf: + - maxItems: 1 + description: PHY control register + - maxItems: 1 + description: iomem address range of DMU (Device Management Unit) + deprecated: true + + reg-names: + items: + - const: dmu + + brcm,syscon-clkset: + description: phandle to syscon for clkset register + $ref: /schemas/types.yaml#/definitions/phandle + + clocks: + items: + - description: USB PHY reference clock + + clock-names: + items: + - const: phy-ref-clk + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - clocks + - clock-names + - "#phy-cells" + +oneOf: + - required: + - brcm,syscon-clkset + - required: + - reg-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/bcm-nsp.h> + phy@1800c164 { + compatible = "brcm,ns-usb2-phy"; + reg = <0x1800c164 0x4>; + brcm,syscon-clkset = <&clkset>; + clocks = <&genpll BCM_NSP_GENPLL_USB_PHY_REF_CLK>; + clock-names = "phy-ref-clk"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.yaml b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.yaml new file mode 100644 index 000000000..7fd419db4 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/bcm-ns-usb3-phy.yaml @@ -0,0 +1,62 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/bcm-ns-usb3-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom Northstar USB 3.0 PHY + +description: | + Initialization of USB 3.0 PHY depends on Northstar version. There are currently + three known series: Ax, Bx and Cx. + Known A0: BCM4707 rev 0 + Known B0: BCM4707 rev 4, BCM53573 rev 2 + Known B1: BCM4707 rev 6 + Known C0: BCM47094 rev 0 + +maintainers: + - RafaĆ MiĆecki <rafal@milecki.pl> + +properties: + compatible: + enum: + - brcm,ns-ax-usb3-phy + - brcm,ns-bx-usb3-phy + + reg: + description: address of MDIO bus device + maxItems: 1 + + usb3-dmp-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the DMP (Device Management Plugin) syscon + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - usb3-dmp-syscon + - "#phy-cells" + +additionalProperties: false + +examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + usb3-phy@10 { + compatible = "brcm,ns-ax-usb3-phy"; + reg = <0x10>; + usb3-dmp-syscon = <&usb3_dmp>; + #phy-cells = <0>; + }; + }; + + usb3_dmp: syscon@18105000 { + reg = <0x18105000 0x1000>; + }; diff --git a/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt b/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt new file mode 100644 index 000000000..c0155f842 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/berlin-sata-phy.txt @@ -0,0 +1,36 @@ +Berlin SATA PHY +--------------- + +Required properties: +- compatible: should be one of + "marvell,berlin2-sata-phy" + "marvell,berlin2q-sata-phy" +- address-cells: should be 1 +- size-cells: should be 0 +- phy-cells: from the generic PHY bindings, must be 1 +- reg: address and length of the register +- clocks: reference to the clock entry + +Sub-nodes: +Each PHY should be represented as a sub-node. + +Sub-nodes required properties: +- reg: the PHY number + +Example: + sata_phy: phy@f7e900a0 { + compatible = "marvell,berlin2q-sata-phy"; + reg = <0xf7e900a0 0x200>; + clocks = <&chip CLKID_SATA>; + #address-cells = <1>; + #size-cells = <0>; + #phy-cells = <1>; + + sata-phy@0 { + reg = <0>; + }; + + sata-phy@1 { + reg = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/berlin-usb-phy.txt b/Documentation/devicetree/bindings/phy/berlin-usb-phy.txt new file mode 100644 index 000000000..be33780f6 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/berlin-usb-phy.txt @@ -0,0 +1,16 @@ +* Marvell Berlin USB PHY + +Required properties: +- compatible: "marvell,berlin2-usb-phy" or "marvell,berlin2cd-usb-phy" +- reg: base address and length of the registers +- #phys-cells: should be 0 +- resets: reference to the reset controller + +Example: + + usb-phy@f774000 { + compatible = "marvell,berlin2-usb-phy"; + reg = <0xf774000 0x128>; + #phy-cells = <0>; + resets = <&chip 0x104 14>; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,bcm63xx-usbh-phy.yaml b/Documentation/devicetree/bindings/phy/brcm,bcm63xx-usbh-phy.yaml new file mode 100644 index 000000000..bd527f566 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,bcm63xx-usbh-phy.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/brcm,bcm63xx-usbh-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: BCM63xx USBH PHY + +maintainers: + - Ălvaro FernĂĄndez Rojas <noltari@gmail.com> + +properties: + compatible: + enum: + - brcm,bcm6318-usbh-phy + - brcm,bcm6328-usbh-phy + - brcm,bcm6358-usbh-phy + - brcm,bcm6362-usbh-phy + - brcm,bcm6368-usbh-phy + - brcm,bcm63268-usbh-phy + + reg: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: usbh + - const: usb_ref + + resets: + maxItems: 1 + + "#phy-cells": + const: 1 + +additionalProperties: false + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - "#phy-cells" + +if: + properties: + compatible: + enum: + - brcm,bcm6318-usbh-phy + - brcm,bcm6328-usbh-phy + - brcm,bcm6362-usbh-phy + - brcm,bcm63268-usbh-phy +then: + properties: + power-domains: + maxItems: 1 + required: + - power-domains +else: + properties: + power-domains: false + +examples: + - | + usbh: usb-phy@10001700 { + compatible = "brcm,bcm6368-usbh-phy"; + reg = <0x10001700 0x38>; + clocks = <&periph_clk 15>; + clock-names = "usbh"; + resets = <&periph_rst 12>; + #phy-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.yaml b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.yaml new file mode 100644 index 000000000..580fbe37b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.yaml @@ -0,0 +1,196 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/brcm,brcmstb-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom STB USB PHY + +description: Broadcom's PHY that handles EHCI/OHCI and/or XHCI + +maintainers: + - Al Cooper <alcooperx@gmail.com> + - RafaĆ MiĆecki <rafal@milecki.pl> + +properties: + compatible: + enum: + - brcm,bcm4908-usb-phy + - brcm,bcm7211-usb-phy + - brcm,bcm7216-usb-phy + - brcm,brcmstb-usb-phy + + reg: + minItems: 1 + items: + - description: the base CTRL register + - description: XHCI EC register + - description: XHCI GBL register + - description: USB PHY register + - description: USB MDIO register + - description: BDC register + + reg-names: + minItems: 1 + items: + - const: ctrl + - const: xhci_ec + - const: xhci_gbl + - const: usb_phy + - const: usb_mdio + - const: bdc_ec + + power-domains: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: sw_usb + - const: sw_usb3 + + interrupts: + description: wakeup interrupt + + interrupt-names: + const: wake + + brcm,ipp: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Invert Port Power + minimum: 0 + maximum: 1 + + brcm,ioc: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Invert Over Current detection + minimum: 0 + maximum: 1 + + dr_mode: + description: PHY Device mode. If this property is not defined, the PHY will + default to "host" mode. + enum: + - host + - peripheral + - drd + - typec-pd + + brcm,syscon-piarbctl: + description: phandle to syscon for handling config registers + $ref: /schemas/types.yaml#/definitions/phandle + + brcm,has-xhci: + description: Indicates the PHY has an XHCI PHY. + type: boolean + + brcm,has-eohci: + description: Indicates the PHY has an EHCI/OHCI PHY. + type: boolean + + "#phy-cells": + description: | + Cell allows setting the type of the PHY. Possible values are: + - PHY_TYPE_USB2 for USB1.1/2.0 PHY + - PHY_TYPE_USB3 for USB3.x PHY + const: 1 + +required: + - reg + - "#phy-cells" + +anyOf: + - required: + - brcm,has-xhci + - required: + - brcm,has-eohci + +allOf: + - if: + properties: + compatible: + contains: + enum: + - brcm,bcm4908-usb-phy + - brcm,brcmstb-usb-phy + then: + properties: + reg: + minItems: 1 + maxItems: 2 + - if: + properties: + compatible: + contains: + const: brcm,bcm7211-usb-phy + then: + properties: + reg: + minItems: 5 + maxItems: 6 + reg-names: + minItems: 5 + maxItems: 6 + - if: + properties: + compatible: + contains: + const: brcm,bcm7216-usb-phy + then: + properties: + reg: + minItems: 3 + maxItems: 3 + reg-names: + minItems: 3 + maxItems: 3 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/phy/phy.h> + + usb-phy@f0470200 { + compatible = "brcm,brcmstb-usb-phy"; + reg = <0xf0470200 0xb8>, + <0xf0471940 0x6c0>; + #phy-cells = <1>; + dr_mode = "host"; + brcm,ioc = <1>; + brcm,ipp = <1>; + brcm,has-xhci; + brcm,has-eohci; + clocks = <&usb20>, <&usb30>; + clock-names = "sw_usb", "sw_usb3"; + }; + - | + #include <dt-bindings/phy/phy.h> + + usb-phy@29f0200 { + compatible = "brcm,bcm7211-usb-phy"; + reg = <0x29f0200 0x200>, + <0x29c0880 0x30>, + <0x29cc100 0x534>, + <0x2808000 0x24>, + <0x2980080 0x8>; + reg-names = "ctrl", + "xhci_ec", + "xhci_gbl", + "usb_phy", + "usb_mdio"; + brcm,ioc = <0x0>; + brcm,ipp = <0x0>; + interrupts = <0x30>; + interrupt-parent = <&vpu_intr1_nosec_intc>; + interrupt-names = "wake"; + #phy-cells = <0x1>; + brcm,has-xhci; + brcm,syscon-piarbctl = <&syscon_piarbctl>; + clocks = <&scmi_clk 256>; + clock-names = "sw_usb"; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.yaml new file mode 100644 index 000000000..808e90b24 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,cygnus-pcie-phy.yaml @@ -0,0 +1,77 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/brcm,cygnus-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom Cygnus PCIe PHY + +maintainers: + - Ray Jui <ray.jui@broadcom.com> + - Scott Branden <scott.branden@broadcom.com> + +properties: + $nodename: + pattern: "^pcie[-|_]phy(@.*)?$" + + compatible: + items: + - const: brcm,cygnus-pcie-phy + + reg: + maxItems: 1 + description: > + Base address and length of the PCIe PHY block + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "^pcie-phy@[0-9]+$": + type: object + additionalProperties: false + description: > + PCIe PHY child nodes + + properties: + reg: + maxItems: 1 + description: > + The PCIe PHY port number + + "#phy-cells": + const: 0 + + required: + - reg + - "#phy-cells" + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + pcie_phy: pcie_phy@301d0a0 { + compatible = "brcm,cygnus-pcie-phy"; + reg = <0x0301d0a0 0x14>; + #address-cells = <1>; + #size-cells = <0>; + + pcie0_phy: pcie-phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + + pcie1_phy: pcie-phy@1 { + reg = <1>; + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,kona-usb2-phy.yaml b/Documentation/devicetree/bindings/phy/brcm,kona-usb2-phy.yaml new file mode 100644 index 000000000..d7faeb81f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,kona-usb2-phy.yaml @@ -0,0 +1,36 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/brcm,kona-usb2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom Kona family USB 2.0 PHY + +maintainers: + - Florian Fainelli <f.fainelli@gmail.com> + +properties: + compatible: + const: brcm,kona-usb2-phy + + reg: + maxItems: 1 + + '#phy-cells': + const: 0 + +required: + - compatible + - reg + - '#phy-cells' + +additionalProperties: false + +examples: + - | + usb-phy@3f130000 { + compatible = "brcm,kona-usb2-phy"; + reg = <0x3f130000 0x28>; + #phy-cells = <0>; + }; +... diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt new file mode 100644 index 000000000..04f063aa7 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,ns2-drd-phy.txt @@ -0,0 +1,30 @@ +BROADCOM NORTHSTAR2 USB2 (DUAL ROLE DEVICE) PHY + +Required properties: + - compatible: brcm,ns2-drd-phy + - reg: offset and length of the NS2 PHY related registers. + - reg-names + The below registers must be provided. + icfg - for DRD ICFG configurations + rst-ctrl - for DRD IDM reset + crmu-ctrl - for CRMU core vdd, PHY and PHY PLL reset + usb2-strap - for port over current polarity reversal + - #phy-cells: Must be 0. No args required. + - vbus-gpios: vbus gpio binding + - id-gpios: id gpio binding + +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usbdrd_phy: phy@66000960 { + #phy-cells = <0>; + compatible = "brcm,ns2-drd-phy"; + reg = <0x66000960 0x24>, + <0x67012800 0x4>, + <0x6501d148 0x4>, + <0x664d0700 0x4>; + reg-names = "icfg", "rst-ctrl", + "crmu-ctrl", "usb2-strap"; + id-gpios = <&gpio_g 30 0>; + vbus-gpios = <&gpio_g 31 0>; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,ns2-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/brcm,ns2-pcie-phy.yaml new file mode 100644 index 000000000..527010702 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,ns2-pcie-phy.yaml @@ -0,0 +1,41 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/brcm,ns2-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom NS2 PCIe PHY + +maintainers: + - Ray Jui <ray.jui@broadcom.com> + - Scott Branden <scott.branden@broadcom.com> + +properties: + compatible: + const: brcm,ns2-pcie-phy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - "#phy-cells" + +additionalProperties: false + +examples: + - | + mdio { + #address-cells = <1>; + #size-cells = <0>; + + pci-phy@0 { + compatible = "brcm,ns2-pcie-phy"; + reg = <0x0>; + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,sata-phy.yaml b/Documentation/devicetree/bindings/phy/brcm,sata-phy.yaml new file mode 100644 index 000000000..8467c8e63 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,sata-phy.yaml @@ -0,0 +1,144 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/brcm,sata-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Broadcom SATA3 PHY + +maintainers: + - Florian Fainelli <f.fainelli@gmail.com> + +properties: + $nodename: + pattern: "^sata[-|_]phy(@.*)?$" + + compatible: + oneOf: + - items: + - enum: + - brcm,bcm7216-sata-phy + - brcm,bcm7425-sata-phy + - brcm,bcm7445-sata-phy + - brcm,bcm63138-sata-phy + - const: brcm,phy-sata3 + - items: + - const: brcm,iproc-nsp-sata-phy + - items: + - const: brcm,iproc-ns2-sata-phy + - items: + - const: brcm,iproc-sr-sata-phy + + reg: + minItems: 1 + maxItems: 2 + + reg-names: + minItems: 1 + items: + - const: phy + - const: phy-ctrl + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "^sata-phy@[0-9]+$": + type: object + description: | + Each port's PHY should be represented as a sub-node. + + properties: + reg: + description: The SATA PHY port number + maxItems: 1 + + "#phy-cells": + const: 0 + + "brcm,enable-ssc": + $ref: /schemas/types.yaml#/definitions/flag + description: | + Use spread spectrum clocking (SSC) on this port + This property is not applicable for "brcm,iproc-ns2-sata-phy", + "brcm,iproc-nsp-sata-phy" and "brcm,iproc-sr-sata-phy". + + "brcm,rxaeq-mode": + $ref: /schemas/types.yaml#/definitions/string + description: + String that indicates the desired RX equalizer mode. + enum: + - off + - auto + - manual + + "brcm,rxaeq-value": + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + When 'brcm,rxaeq-mode' is set to "manual", provides the RX + equalizer value that should be used. + minimum: 0 + maximum: 63 + + "brcm,tx-amplitude-millivolt": + description: | + Transmit amplitude voltage in millivolt. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [400, 500, 600, 800] + + required: + - reg + - "#phy-cells" + + additionalProperties: false + +if: + properties: + compatible: + const: brcm,iproc-ns2-sata-phy +then: + properties: + reg: + minItems: 2 + + reg-names: + minItems: 2 +else: + properties: + reg: + maxItems: 1 + + reg-names: + maxItems: 1 + +required: + - compatible + - "#address-cells" + - "#size-cells" + - reg + - reg-names + +additionalProperties: false + +examples: + - | + sata_phy@f0458100 { + compatible = "brcm,bcm7445-sata-phy", "brcm,phy-sata3"; + reg = <0xf0458100 0x1e00>; + reg-names = "phy"; + #address-cells = <1>; + #size-cells = <0>; + + sata-phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + + sata-phy@1 { + reg = <1>; + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,sr-pcie-phy.txt b/Documentation/devicetree/bindings/phy/brcm,sr-pcie-phy.txt new file mode 100644 index 000000000..e8d82286b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,sr-pcie-phy.txt @@ -0,0 +1,41 @@ +Broadcom Stingray PCIe PHY + +Required properties: +- compatible: must be "brcm,sr-pcie-phy" +- reg: base address and length of the PCIe SS register space +- brcm,sr-cdru: phandle to the CDRU syscon node +- brcm,sr-mhb: phandle to the MHB syscon node +- #phy-cells: Must be 1, denotes the PHY index + +For PAXB based root complex, one can have a configuration of up to 8 PHYs +PHY index goes from 0 to 7 + +For the internal PAXC based root complex, PHY index is always 8 + +Example: + mhb: syscon@60401000 { + compatible = "brcm,sr-mhb", "syscon"; + reg = <0 0x60401000 0 0x38c>; + }; + + cdru: syscon@6641d000 { + compatible = "brcm,sr-cdru", "syscon"; + reg = <0 0x6641d000 0 0x400>; + }; + + pcie_phy: phy@40000000 { + compatible = "brcm,sr-pcie-phy"; + reg = <0 0x40000000 0 0x800>; + brcm,sr-cdru = <&cdru>; + brcm,sr-mhb = <&mhb>; + #phy-cells = <1>; + }; + + /* users of the PCIe PHY */ + + pcie0: pcie@48000000 { + ... + ... + phys = <&pcie_phy 0>; + phy-names = "pcie-phy"; + }; diff --git a/Documentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txt b/Documentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txt new file mode 100644 index 000000000..4ba298966 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/brcm,stingray-usb-phy.txt @@ -0,0 +1,32 @@ +Broadcom Stingray USB PHY + +Required properties: + - compatible : should be one of the listed compatibles + - "brcm,sr-usb-combo-phy" is combo PHY has two PHYs, one SS and one HS. + - "brcm,sr-usb-hs-phy" is a single HS PHY. + - reg: offset and length of the PHY blocks registers + - #phy-cells: + - Must be 1 for brcm,sr-usb-combo-phy as it expects one argument to indicate + the PHY number of two PHYs. 0 for HS PHY and 1 for SS PHY. + - Must be 0 for brcm,sr-usb-hs-phy. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usbphy0: usb-phy@0 { + compatible = "brcm,sr-usb-combo-phy"; + reg = <0x00000000 0x100>; + #phy-cells = <1>; + }; + + usbphy1: usb-phy@10000 { + compatible = "brcm,sr-usb-combo-phy"; + reg = <0x00010000 0x100>, + #phy-cells = <1>; + }; + + usbphy2: usb-phy@20000 { + compatible = "brcm,sr-usb-hs-phy"; + reg = <0x00020000 0x100>, + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/calxeda-combophy.yaml b/Documentation/devicetree/bindings/phy/calxeda-combophy.yaml new file mode 100644 index 000000000..d05a7c793 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/calxeda-combophy.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/calxeda-combophy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Calxeda Highbank Combination PHYs for SATA + +description: | + The Calxeda Combination PHYs connect the SoC to the internal fabric + and to SATA connectors. The PHYs support multiple protocols (SATA, + SGMII, PCIe) and can be assigned to different devices (SATA or XGMAC + controller). + Programming the PHYs is typically handled by those device drivers, + not by a dedicated PHY driver. + +maintainers: + - Andre Przywara <andre.przywara@arm.com> + +properties: + compatible: + const: calxeda,hb-combophy + + '#phy-cells': + const: 1 + + reg: + maxItems: 1 + + phydev: + description: device ID for programming the ComboPHY. + $ref: /schemas/types.yaml#/definitions/uint32 + maximum: 31 + +required: + - compatible + - reg + - phydev + - '#phy-cells' + +additionalProperties: false + +examples: + - | + combophy5: combo-phy@fff5d000 { + compatible = "calxeda,hb-combophy"; + #phy-cells = <1>; + reg = <0xfff5d000 0x1000>; + phydev = <31>; + }; diff --git a/Documentation/devicetree/bindings/phy/cdns,dphy-rx.yaml b/Documentation/devicetree/bindings/phy/cdns,dphy-rx.yaml new file mode 100644 index 000000000..6fdd46ad5 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/cdns,dphy-rx.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/cdns,dphy-rx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cadence DPHY Rx + +maintainers: + - Pratyush Yadav <pratyush@kernel.org> + +properties: + compatible: + items: + - const: cdns,dphy-rx + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/soc/ti,sci_pm_domain.h> + + dphy0: phy@4580000 { + compatible = "cdns,dphy-rx"; + reg = <0x4580000 0x1100>; + #phy-cells = <0>; + power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>; + }; diff --git a/Documentation/devicetree/bindings/phy/cdns,dphy.yaml b/Documentation/devicetree/bindings/phy/cdns,dphy.yaml new file mode 100644 index 000000000..6cd9b0f38 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/cdns,dphy.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/cdns,dphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cadence DPHY + +maintainers: + - Pratyush Yadav <pratyush@kernel.org> + +properties: + compatible: + enum: + - cdns,dphy + - ti,j721e-dphy + + reg: + maxItems: 1 + + clocks: + items: + - description: PMA state machine clock + - description: PLL reference clock + + clock-names: + items: + - const: psm + - const: pll_ref + + "#phy-cells": + const: 0 + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/soc/ti,sci_pm_domain.h> + + dphy0: phy@fd0e0000{ + compatible = "cdns,dphy"; + reg = <0xfd0e0000 0x1000>; + clocks = <&psm_clk>, <&pll_ref_clk>; + clock-names = "psm", "pll_ref"; + power-domains = <&k3_pds 147 TI_SCI_PD_EXCLUSIVE>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/cdns,salvo-phy.yaml b/Documentation/devicetree/bindings/phy/cdns,salvo-phy.yaml new file mode 100644 index 000000000..c7281a7c8 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/cdns,salvo-phy.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright (c) 2020 NXP +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/cdns,salvo-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cadence SALVO PHY + +maintainers: + - Peter Chen <peter.chen@nxp.com> + +properties: + compatible: + enum: + - nxp,salvo-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: salvo_phy_clk + + power-domains: + maxItems: 1 + + "#phy-cells": + const: 0 + + cdns,usb2-disconnect-threshold-microvolt: + description: The microvolt threshold value utilized for detecting + USB disconnection event. + enum: [575, 610, 645] + default: 575 + +required: + - compatible + - reg + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/firmware/imx/rsrc.h> + + usb3phy: usb3-phy@5b160000 { + compatible = "nxp,salvo-phy"; + reg = <0x5b160000 0x40000>; + clocks = <&usb3_lpcg 4>; + clock-names = "salvo_phy_clk"; + power-domains = <&pd IMX_SC_R_USB_2_PHY>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/dm816x-phy.txt b/Documentation/devicetree/bindings/phy/dm816x-phy.txt new file mode 100644 index 000000000..2fe3d11d0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/dm816x-phy.txt @@ -0,0 +1,24 @@ +Device tree binding documentation for am816x USB PHY +========================= + +Required properties: +- compatible : should be "ti,dm816x-usb-phy" +- reg : offset and length of the PHY register set. +- reg-names : name for the phy registers +- clocks : phandle to the clock +- clock-names : name of the clock +- syscon: phandle for the syscon node to access misc registers +- #phy-cells : from the generic PHY bindings, must be 1 +- syscon: phandle for the syscon node to access misc registers + +Example: + +usb_phy0: usb-phy@20 { + compatible = "ti,dm8168-usb-phy"; + reg = <0x20 0x8>; + reg-names = "phy"; + clocks = <&main_fapll 6>; + clock-names = "refclk"; + #phy-cells = <0>; + syscon = <&scm_conf>; +}; diff --git a/Documentation/devicetree/bindings/phy/fsl,imx8-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/fsl,imx8-pcie-phy.yaml new file mode 100644 index 000000000..182a21938 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/fsl,imx8-pcie-phy.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/fsl,imx8-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX8 SoC series PCIe PHY + +maintainers: + - Richard Zhu <hongxing.zhu@nxp.com> + +properties: + "#phy-cells": + const: 0 + + compatible: + enum: + - fsl,imx8mm-pcie-phy + - fsl,imx8mp-pcie-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: ref + + resets: + minItems: 1 + maxItems: 2 + + reset-names: + oneOf: + - items: # for iMX8MM + - const: pciephy + - items: # for IMX8MP + - const: pciephy + - const: perst + + fsl,refclk-pad-mode: + description: | + Specifies the mode of the refclk pad used. It can be UNUSED(PHY + refclock is derived from SoC internal source), INPUT(PHY refclock + is provided externally via the refclk pad) or OUTPUT(PHY refclock + is derived from SoC internal source and provided on the refclk pad). + Refer include/dt-bindings/phy/phy-imx8-pcie.h for the constants + to be used. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2 ] + + fsl,tx-deemph-gen1: + description: Gen1 De-emphasis value (optional). + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0 + + fsl,tx-deemph-gen2: + description: Gen2 De-emphasis value (optional). + $ref: /schemas/types.yaml#/definitions/uint32 + default: 0 + + fsl,clkreq-unsupported: + type: boolean + description: A boolean property indicating the CLKREQ# signal is + not supported in the board design (optional) + + power-domains: + description: PCIe PHY power domain (optional). + maxItems: 1 + +required: + - "#phy-cells" + - compatible + - reg + - clocks + - clock-names + - fsl,refclk-pad-mode + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mm-clock.h> + #include <dt-bindings/phy/phy-imx8-pcie.h> + #include <dt-bindings/reset/imx8mq-reset.h> + + pcie_phy: pcie-phy@32f00000 { + compatible = "fsl,imx8mm-pcie-phy"; + reg = <0x32f00000 0x10000>; + clocks = <&clk IMX8MM_CLK_PCIE1_PHY>; + clock-names = "ref"; + assigned-clocks = <&clk IMX8MM_CLK_PCIE1_PHY>; + assigned-clock-rates = <100000000>; + assigned-clock-parents = <&clk IMX8MM_SYS_PLL2_100M>; + resets = <&src IMX8MQ_RESET_PCIEPHY>; + reset-names = "pciephy"; + fsl,refclk-pad-mode = <IMX8_PCIE_REFCLK_PAD_INPUT>; + #phy-cells = <0>; + }; +... diff --git a/Documentation/devicetree/bindings/phy/fsl,imx8mq-usb-phy.yaml b/Documentation/devicetree/bindings/phy/fsl,imx8mq-usb-phy.yaml new file mode 100644 index 000000000..dc3a3f709 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/fsl,imx8mq-usb-phy.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/fsl,imx8mq-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale i.MX8MQ USB3 PHY + +maintainers: + - Li Jun <jun.li@nxp.com> + +properties: + compatible: + enum: + - fsl,imx8mq-usb-phy + - fsl,imx8mp-usb-phy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: phy + + power-domains: + maxItems: 1 + + vbus-supply: + description: + A phandle to the regulator for USB VBUS. + + fsl,phy-tx-vref-tune-percent: + description: + Tunes the HS DC level relative to the nominal level + minimum: 94 + maximum: 124 + + fsl,phy-tx-rise-tune-percent: + description: + Adjusts the rise/fall time duration of the HS waveform relative to + its nominal value + minimum: 97 + maximum: 103 + + fsl,phy-tx-preemp-amp-tune-microamp: + description: + Adjust amount of current sourced to DPn and DMn after a J-to-K + or K-to-J transition. Default is 0 (disabled). + minimum: 0 + maximum: 1800 + + fsl,phy-tx-vboost-level-microvolt: + description: + Adjust the boosted transmit launch pk-pk differential amplitude + minimum: 880 + maximum: 1120 + + fsl,phy-comp-dis-tune-percent: + description: + Adjust the voltage level used to detect a disconnect event at the host + relative to the nominal value + minimum: 91 + maximum: 115 + + fsl,phy-pcs-tx-deemph-3p5db-attenuation-db: + description: + Adjust TX de-emphasis attenuation in dB at nominal + 3.5dB point as per USB specification + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 36 + + fsl,phy-pcs-tx-swing-full-percent: + description: + Scaling of the voltage defined by fsl,phy-tx-vboost-level-microvolt + minimum: 0 + maximum: 100 + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mq-clock.h> + usb3_phy0: phy@381f0040 { + compatible = "fsl,imx8mq-usb-phy"; + reg = <0x381f0040 0x40>; + clocks = <&clk IMX8MQ_CLK_USB1_PHY_ROOT>; + clock-names = "phy"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/fsl,imx8qm-lvds-phy.yaml b/Documentation/devicetree/bindings/phy/fsl,imx8qm-lvds-phy.yaml new file mode 100644 index 000000000..8767e48c7 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/fsl,imx8qm-lvds-phy.yaml @@ -0,0 +1,61 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/fsl,imx8qm-lvds-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mixel LVDS PHY for Freescale i.MX8qm SoC + +maintainers: + - Liu Ying <victor.liu@nxp.com> + +description: | + The Mixel LVDS PHY IP block is found on Freescale i.MX8qm SoC. + It converts two groups of four 7/10 bits of CMOS data into two + groups of four data lanes of LVDS data streams. A phase-locked + transmit clock is transmitted in parallel with each group of + data streams over a fifth LVDS link. Every cycle of the transmit + clock, 56/80 bits of input data are sampled and transmitted + through the two groups of LVDS data streams. Together with the + transmit clocks, the two groups of LVDS data streams form two + LVDS channels. + + The Mixel LVDS PHY found on Freescale i.MX8qm SoC is controlled + by Control and Status Registers(CSR) module in the SoC. The CSR + module, as a system controller, contains the PHY's registers. + +properties: + compatible: + enum: + - fsl,imx8qm-lvds-phy + - mixel,28fdsoi-lvds-1250-8ch-tx-pll + + "#phy-cells": + const: 1 + description: | + Cell allows setting the LVDS channel index of the PHY. + Index 0 is for LVDS channel0 and index 1 is for LVDS channel1. + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + +required: + - compatible + - "#phy-cells" + - clocks + - power-domains + +additionalProperties: false + +examples: + - | + #include <dt-bindings/firmware/imx/rsrc.h> + phy { + compatible = "fsl,imx8qm-lvds-phy"; + #phy-cells = <1>; + clocks = <&clk IMX_SC_R_LVDS_0 IMX_SC_PM_CLK_PHY>; + power-domains = <&pd IMX_SC_R_LVDS_0>; + }; diff --git a/Documentation/devicetree/bindings/phy/fsl,lynx-28g.yaml b/Documentation/devicetree/bindings/phy/fsl,lynx-28g.yaml new file mode 100644 index 000000000..ff9f9ca0f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/fsl,lynx-28g.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/fsl,lynx-28g.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale Lynx 28G SerDes PHY + +maintainers: + - Ioana Ciornei <ioana.ciornei@nxp.com> + +properties: + compatible: + enum: + - fsl,lynx-28g + + reg: + maxItems: 1 + + "#phy-cells": + const: 1 + +required: + - compatible + - reg + - "#phy-cells" + +additionalProperties: false + +examples: + - | + soc { + #address-cells = <2>; + #size-cells = <2>; + serdes_1: phy@1ea0000 { + compatible = "fsl,lynx-28g"; + reg = <0x0 0x1ea0000 0x0 0x1e30>; + #phy-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/fsl,mxs-usbphy.yaml b/Documentation/devicetree/bindings/phy/fsl,mxs-usbphy.yaml new file mode 100644 index 000000000..f4b1ca2fb --- /dev/null +++ b/Documentation/devicetree/bindings/phy/fsl,mxs-usbphy.yaml @@ -0,0 +1,128 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/fsl,mxs-usbphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale MXS USB Phy Device + +maintainers: + - Xu Yang <xu.yang_2@nxp.com> + +properties: + compatible: + oneOf: + - enum: + - fsl,imx23-usbphy + - fsl,imx7ulp-usbphy + - fsl,vf610-usbphy + - items: + - enum: + - fsl,imx28-usbphy + - fsl,imx6ul-usbphy + - fsl,imx6sl-usbphy + - fsl,imx6sx-usbphy + - fsl,imx6q-usbphy + - const: fsl,imx23-usbphy + - items: + - const: fsl,imx6sll-usbphy + - const: fsl,imx6ul-usbphy + - const: fsl,imx23-usbphy + - items: + - enum: + - fsl,imx8dxl-usbphy + - fsl,imx8qm-usbphy + - fsl,imx8ulp-usbphy + - const: fsl,imx7ulp-usbphy + + reg: + maxItems: 1 + + interrupts: + maxItems: 1 + + clocks: + maxItems: 1 + + '#phy-cells': + const: 0 + + power-domains: + maxItems: 1 + + fsl,anatop: + description: + phandle for anatop register, it is only for imx6 SoC series. + $ref: /schemas/types.yaml#/definitions/phandle + + phy-3p0-supply: + description: + One of USB PHY's power supply. Can be used to keep a good signal + quality. + + fsl,tx-cal-45-dn-ohms: + description: + Resistance (in ohms) of switchable high-speed trimming resistor + connected in parallel with the 45 ohm resistor that terminates + the DN output signal. + minimum: 35 + maximum: 54 + default: 45 + + fsl,tx-cal-45-dp-ohms: + description: + Resistance (in ohms) of switchable high-speed trimming resistor + connected in parallel with the 45 ohm resistor that terminates + the DP output signal. + minimum: 35 + maximum: 54 + default: 45 + + fsl,tx-d-cal: + description: + Current trimming value (as a percentage) of the 17.78 mA TX + reference current. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 79 + maximum: 119 + default: 100 + +required: + - compatible + - reg + - clocks + +allOf: + - if: + properties: + compatible: + oneOf: + - enum: + - fsl,imx6q-usbphy + - fsl,imx6sl-usbphy + - fsl,imx6sx-usbphy + - fsl,imx6sll-usbphy + - fsl,vf610-usbphy + - items: + - const: fsl,imx6ul-usbphy + - const: fsl,imx23-usbphy + then: + required: + - fsl,anatop + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/clock/imx6qdl-clock.h> + + usbphy1: usb-phy@20c9000 { + compatible = "fsl,imx6q-usbphy", "fsl,imx23-usbphy"; + reg = <0x020c9000 0x1000>; + clocks = <&clks IMX6QDL_CLK_USBPHY1>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; + fsl,anatop = <&anatop>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/hisilicon,hi3660-usb3.yaml b/Documentation/devicetree/bindings/phy/hisilicon,hi3660-usb3.yaml new file mode 100644 index 000000000..405c6b0b8 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/hisilicon,hi3660-usb3.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/hisilicon,hi3660-usb3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hisilicon Kirin 960 USB PHY + +maintainers: + - Mauro Carvalho Chehab <mchehab+huawei@kernel.org> +description: |+ + Bindings for USB3 PHY on HiSilicon Kirin 960. + +properties: + compatible: + const: hisilicon,hi3660-usb-phy + + "#phy-cells": + const: 0 + + hisilicon,pericrg-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle of syscon used to control iso refclk. + + hisilicon,pctrl-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle of syscon used to control usb tcxo. + + hisilicon,eye-diagram-param: + $ref: /schemas/types.yaml#/definitions/uint32-array + maxItems: 1 + description: Eye diagram for phy. + +required: + - compatible + - hisilicon,pericrg-syscon + - hisilicon,pctrl-syscon + - hisilicon,eye-diagram-param + - "#phy-cells" + +additionalProperties: false + +examples: + - | + usb-phy { + compatible = "hisilicon,hi3660-usb-phy"; + #phy-cells = <0>; + hisilicon,pericrg-syscon = <&crg_ctrl>; + hisilicon,pctrl-syscon = <&pctrl>; + hisilicon,eye-diagram-param = <0x22466e4>; + }; diff --git a/Documentation/devicetree/bindings/phy/hisilicon,hi3670-usb3.yaml b/Documentation/devicetree/bindings/phy/hisilicon,hi3670-usb3.yaml new file mode 100644 index 000000000..a1a8a84df --- /dev/null +++ b/Documentation/devicetree/bindings/phy/hisilicon,hi3670-usb3.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/hisilicon,hi3670-usb3.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Hisilicon Kirin970 USB PHY + +maintainers: + - Mauro Carvalho Chehab <mchehab+huawei@kernel.org> + +description: |+ + Bindings for USB3 PHY on HiSilicon Kirin 970. + +properties: + compatible: + const: hisilicon,hi3670-usb-phy + + "#phy-cells": + const: 0 + + hisilicon,pericrg-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle of syscon used to control iso refclk. + + hisilicon,pctrl-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle of syscon used to control usb tcxo. + + hisilicon,sctrl-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle of syscon used to control phy deep sleep. + + hisilicon,eye-diagram-param: + $ref: /schemas/types.yaml#/definitions/uint32-array + maxItems: 1 + description: Eye diagram for phy. + + hisilicon,tx-vboost-lvl: + $ref: /schemas/types.yaml#/definitions/uint32 + description: TX level vboost for phy. + +required: + - compatible + - hisilicon,pericrg-syscon + - hisilicon,pctrl-syscon + - hisilicon,sctrl-syscon + - hisilicon,eye-diagram-param + - hisilicon,tx-vboost-lvl + - "#phy-cells" + +additionalProperties: false + +examples: + - | + usb-phy { + compatible = "hisilicon,hi3670-usb-phy"; + #phy-cells = <0>; + hisilicon,pericrg-syscon = <&crg_ctrl>; + hisilicon,pctrl-syscon = <&pctrl>; + hisilicon,sctrl-syscon = <&sctrl>; + hisilicon,eye-diagram-param = <0xfdfee4>; + hisilicon,tx-vboost-lvl = <0x5>; + }; diff --git a/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml b/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml new file mode 100644 index 000000000..17367a027 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml @@ -0,0 +1,82 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/hisilicon,phy-hi3670-pcie.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: HiSilicon Kirin970 PCIe PHY + +maintainers: + - Mauro Carvalho Chehab <mchehab+huawei@kernel.org> + +description: |+ + Bindings for PCIe PHY on HiSilicon Kirin 970. + +properties: + compatible: + const: hisilicon,hi970-pcie-phy + + "#phy-cells": + const: 0 + + reg: + maxItems: 1 + description: PHY Control registers + + phy-supply: + description: The PCIe PHY power supply + + clocks: + items: + - description: PCIe PHY clock + - description: PCIe AUX clock + - description: PCIe APB PHY clock + - description: PCIe APB SYS clock + - description: PCIe ACLK clock + + clock-names: + items: + - const: phy_ref + - const: aux + - const: apb_phy + - const: apb_sys + - const: aclk + + hisilicon,eye-diagram-param: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: Eye diagram for phy. + +required: + - "#phy-cells" + - compatible + - reg + - clocks + - clock-names + - hisilicon,eye-diagram-param + - phy-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/hi3670-clock.h> + + soc { + #address-cells = <2>; + #size-cells = <2>; + pcie_phy: pcie-phy@fc000000 { + compatible = "hisilicon,hi970-pcie-phy"; + reg = <0x0 0xfc000000 0x0 0x80000>; + #phy-cells = <0>; + phy-supply = <&ldo33>; + clocks = <&crg_ctrl HI3670_CLK_GATE_PCIEPHY_REF>, + <&crg_ctrl HI3670_CLK_GATE_PCIEAUX>, + <&crg_ctrl HI3670_PCLK_GATE_PCIE_PHY>, + <&crg_ctrl HI3670_PCLK_GATE_PCIE_SYS>, + <&crg_ctrl HI3670_ACLK_GATE_PCIE>; + clock-names = "phy_ref", "aux", + "apb_phy", "apb_sys", "aclk"; + hisilicon,eye-diagram-param = <0xffffffff 0xffffffff + 0xffffffff 0xffffffff 0xffffffff>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt b/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt new file mode 100644 index 000000000..296168b74 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/hix5hd2-phy.txt @@ -0,0 +1,22 @@ +Hisilicon hix5hd2 SATA PHY +----------------------- + +Required properties: +- compatible: should be "hisilicon,hix5hd2-sata-phy" +- reg: offset and length of the PHY registers +- #phy-cells: must be 0 +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Optional Properties: +- hisilicon,peripheral-syscon: phandle of syscon used to control peripheral. +- hisilicon,power-reg: offset and bit number within peripheral-syscon, + register of controlling sata power supply. + +Example: + sata_phy: phy@f9900000 { + compatible = "hisilicon,hix5hd2-sata-phy"; + reg = <0xf9900000 0x10000>; + #phy-cells = <0>; + hisilicon,peripheral-syscon = <&peripheral_ctrl>; + hisilicon,power-reg = <0x8 10>; + }; diff --git a/Documentation/devicetree/bindings/phy/ingenic,phy-usb.yaml b/Documentation/devicetree/bindings/phy/ingenic,phy-usb.yaml new file mode 100644 index 000000000..30b42008d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/ingenic,phy-usb.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/ingenic,phy-usb.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ingenic SoCs USB PHY + +maintainers: + - Paul Cercueil <paul@crapouillou.net> + - ćšç°æ° (Zhou Yanjie) <zhouyanjie@wanyeetech.com> + +properties: + $nodename: + pattern: '^usb-phy@.*' + + compatible: + enum: + - ingenic,jz4770-phy + - ingenic,jz4775-phy + - ingenic,jz4780-phy + - ingenic,x1000-phy + - ingenic,x1830-phy + - ingenic,x2000-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + vcc-supply: + description: VCC power supply + + '#phy-cells': + const: 0 + +required: + - compatible + - reg + - clocks + - vcc-supply + - '#phy-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/ingenic,jz4770-cgu.h> + otg_phy: usb-phy@3c { + compatible = "ingenic,jz4770-phy"; + reg = <0x3c 0x10>; + + vcc-supply = <&vcc>; + clocks = <&cgu JZ4770_CLK_OTG_PHY>; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/intel,combo-phy.yaml b/Documentation/devicetree/bindings/phy/intel,combo-phy.yaml new file mode 100644 index 000000000..7dd6a4d94 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/intel,combo-phy.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/intel,combo-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Intel ComboPhy Subsystem + +maintainers: + - Dilip Kota <eswara.kota@linux.intel.com> + +description: | + Intel Combophy subsystem supports PHYs for PCIe, EMAC and SATA + controllers. A single Combophy provides two PHY instances. + +properties: + $nodename: + pattern: "combophy(@.*|-([0-9]|[1-9][0-9]+))?$" + + compatible: + items: + - const: intel,combophy-lgm + - const: intel,combo-phy + + clocks: + maxItems: 1 + + reg: + items: + - description: ComboPhy core registers + - description: PCIe app core control registers + + reg-names: + items: + - const: core + - const: app + + resets: + maxItems: 4 + + reset-names: + items: + - const: phy + - const: core + - const: iphy0 + - const: iphy1 + + intel,syscfg: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to Chip configuration registers + - description: ComboPhy instance id + description: Chip configuration registers handle and ComboPhy instance id + + intel,hsio: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to HSIO registers + - description: ComboPhy instance id + description: HSIO registers handle and ComboPhy instance id on NOC + + intel,aggregation: + type: boolean + description: | + Specify the flag to configure ComboPHY in dual lane mode. + + intel,phy-mode: + $ref: /schemas/types.yaml#/definitions/uint32 + description: | + Mode of the two phys in ComboPhy. + See dt-bindings/phy/phy.h for values. + + "#phy-cells": + const: 1 + +required: + - compatible + - clocks + - reg + - reg-names + - intel,syscfg + - intel,hsio + - intel,phy-mode + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/phy/phy.h> + combophy@d0a00000 { + compatible = "intel,combophy-lgm", "intel,combo-phy"; + clocks = <&cgu0 1>; + #phy-cells = <1>; + reg = <0xd0a00000 0x40000>, + <0xd0a40000 0x1000>; + reg-names = "core", "app"; + resets = <&rcu0 0x50 6>, + <&rcu0 0x50 17>, + <&rcu0 0x50 23>, + <&rcu0 0x50 24>; + reset-names = "phy", "core", "iphy0", "iphy1"; + intel,syscfg = <&sysconf 0>; + intel,hsio = <&hsiol 0>; + intel,phy-mode = <PHY_TYPE_PCIE>; + intel,aggregation; + }; diff --git a/Documentation/devicetree/bindings/phy/intel,keembay-phy-usb.yaml b/Documentation/devicetree/bindings/phy/intel,keembay-phy-usb.yaml new file mode 100644 index 000000000..5cee4c85f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/intel,keembay-phy-usb.yaml @@ -0,0 +1,44 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/intel,keembay-phy-usb.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Intel Keem Bay USB PHY + +maintainers: + - Wan Ahmad Zainie <wan.ahmad.zainie.wan.mohamad@intel.com> + +properties: + compatible: + const: intel,keembay-usb-phy + + reg: + items: + - description: USB APB CPR (clock, power, reset) register + - description: USB APB slave register + + reg-names: + items: + - const: cpr-apb-base + - const: slv-apb-base + + '#phy-cells': + const: 0 + +required: + - compatible + - reg + - '#phy-cells' + +additionalProperties: false + +examples: + - | + usb-phy@20400000 { + compatible = "intel,keembay-usb-phy"; + reg = <0x20400000 0x1c>, + <0x20480000 0xd0>; + reg-names = "cpr-apb-base", "slv-apb-base"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml b/Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml new file mode 100644 index 000000000..ca818f835 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/intel,lgm-emmc-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Intel Lightning Mountain(LGM) eMMC PHY + +maintainers: + - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com> + +description: |+ + Bindings for eMMC PHY on Intel's Lightning Mountain SoC, syscon + node is used to reference the base address of eMMC phy registers. + + The eMMC PHY node should be the child of a syscon node with the + required property: + + - compatible: Should be one of the following: + "intel,lgm-syscon", "syscon" + - reg: + maxItems: 1 + +properties: + compatible: + enum: + - intel,lgm-emmc-phy + - intel,keembay-emmc-phy + + "#phy-cells": + const: 0 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: emmcclk + +required: + - "#phy-cells" + - compatible + - reg + - clocks + +additionalProperties: false + +examples: + - | + sysconf: chiptop@e0200000 { + compatible = "intel,lgm-syscon", "syscon"; + reg = <0xe0200000 0x100>; + #address-cells = <1>; + #size-cells = <1>; + + emmc_phy: emmc-phy@a8 { + compatible = "intel,lgm-emmc-phy"; + reg = <0x00a8 0x10>; + clocks = <&emmc>; + #phy-cells = <0>; + }; + }; + + - | + phy@20290000 { + compatible = "intel,keembay-emmc-phy"; + reg = <0x20290000 0x54>; + clocks = <&emmc>; + clock-names = "emmcclk"; + #phy-cells = <0>; + }; +... diff --git a/Documentation/devicetree/bindings/phy/intel,lgm-usb-phy.yaml b/Documentation/devicetree/bindings/phy/intel,lgm-usb-phy.yaml new file mode 100644 index 000000000..653a12286 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/intel,lgm-usb-phy.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/intel,lgm-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Intel LGM USB PHY + +maintainers: + - Vadivel Murugan Ramuthevar <vadivel.muruganx.ramuthevar@linux.intel.com> + +properties: + compatible: + const: intel,lgm-usb-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + items: + - description: USB PHY and Host controller reset + - description: APB BUS reset + - description: General Hardware reset + + reset-names: + items: + - const: phy + - const: apb + - const: phy31 + + "#phy-cells": + const: 0 + +required: + - compatible + - clocks + - reg + - resets + - reset-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + usb-phy@e7e00000 { + compatible = "intel,lgm-usb-phy"; + reg = <0xe7e00000 0x10000>; + clocks = <&cgu0 153>; + resets = <&rcu 0x70 0x24>, + <&rcu 0x70 0x26>, + <&rcu 0x70 0x28>; + reset-names = "phy", "apb", "phy31"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt b/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt new file mode 100644 index 000000000..300830dda --- /dev/null +++ b/Documentation/devicetree/bindings/phy/keystone-usb-phy.txt @@ -0,0 +1,19 @@ +TI Keystone USB PHY + +Required properties: + - compatible: should be "ti,keystone-usbphy". + - #address-cells, #size-cells : should be '1' if the device has sub-nodes + with 'reg' property. + - reg : Address and length of the usb phy control register set. + +The main purpose of this PHY driver is to enable the USB PHY reference clock +gate on the Keystone SOC for both the USB2 and USB3 PHY. Otherwise it is just +an NOP PHY driver. Hence this node is referenced as both the usb2 and usb3 +phy node in the USB Glue layer driver node. + +usb_phy: usb_phy@2620738 { + compatible = "ti,keystone-usbphy"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x2620738 32>; +}; diff --git a/Documentation/devicetree/bindings/phy/lantiq,vrx200-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/lantiq,vrx200-pcie-phy.yaml new file mode 100644 index 000000000..711de06bb --- /dev/null +++ b/Documentation/devicetree/bindings/phy/lantiq,vrx200-pcie-phy.yaml @@ -0,0 +1,95 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/lantiq,vrx200-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Lantiq VRX200 and ARX300 PCIe PHY + +maintainers: + - Martin Blumenstingl <martin.blumenstingl@googlemail.com> + +properties: + "#phy-cells": + const: 1 + description: selects the PHY mode as defined in <dt-bindings/phy/phy-lantiq-vrx200-pcie.h> + + compatible: + enum: + - lantiq,vrx200-pcie-phy + - lantiq,arx300-pcie-phy + + reg: + maxItems: 1 + + clocks: + items: + - description: PHY module clock + - description: PDI register clock + + clock-names: + items: + - const: phy + - const: pdi + + resets: + items: + - description: exclusive PHY reset line + - description: shared reset line between the PCIe PHY and PCIe controller + + reset-names: + items: + - const: phy + - const: pcie + + lantiq,rcu: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to the RCU syscon + + lantiq,rcu-endian-offset: + $ref: /schemas/types.yaml#/definitions/uint32 + description: the offset of the endian registers for this PHY instance in the RCU syscon + + lantiq,rcu-big-endian-mask: + $ref: /schemas/types.yaml#/definitions/uint32 + description: the mask to set the PDI (PHY) registers for this PHY instance to big endian + + big-endian: + description: Configures the PDI (PHY) registers in big-endian mode + type: boolean + + little-endian: + description: Configures the PDI (PHY) registers in big-endian mode + type: boolean + +required: + - "#phy-cells" + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - lantiq,rcu + - lantiq,rcu-endian-offset + - lantiq,rcu-big-endian-mask + +additionalProperties: false + +examples: + - | + pcie0_phy: phy@106800 { + compatible = "lantiq,vrx200-pcie-phy"; + reg = <0x106800 0x100>; + lantiq,rcu = <&rcu0>; + lantiq,rcu-endian-offset = <0x4c>; + lantiq,rcu-big-endian-mask = <0x80>; /* bit 7 */ + big-endian; + clocks = <&pmu 32>, <&pmu 36>; + clock-names = "phy", "pdi"; + resets = <&reset0 12 24>, <&reset0 22 22>; + reset-names = "phy", "pcie"; + #phy-cells = <1>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/marvell,armada-3700-utmi-phy.yaml b/Documentation/devicetree/bindings/phy/marvell,armada-3700-utmi-phy.yaml new file mode 100644 index 000000000..3aa1a4679 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/marvell,armada-3700-utmi-phy.yaml @@ -0,0 +1,57 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) + +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/marvell,armada-3700-utmi-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell Armada UTMI/UTMI+ PHY + +maintainers: + - Miquel Raynal <miquel.raynal@bootlin.com> + +description: + On Armada 3700, there are two USB controllers, one is compatible with + the USB2 and USB3 specifications and supports OTG. The other one is USB2 + compliant and only supports host mode. Both of these controllers come with + a slightly different UTMI PHY. + +properties: + compatible: + enum: + - marvell,a3700-utmi-host-phy + - marvell,a3700-utmi-otg-phy + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + marvell,usb-misc-reg: + description: + Phandle on the "USB miscellaneous registers" shared region + covering registers related to both the host controller and + the PHY. + $ref: /schemas/types.yaml#/definitions/phandle + +required: + - compatible + - reg + - "#phy-cells" + - marvell,usb-misc-reg + +additionalProperties: false + +examples: + - | + usb2_utmi_host_phy: phy@5f000 { + compatible = "marvell,a3700-utmi-host-phy"; + reg = <0x5f000 0x800>; + marvell,usb-misc-reg = <&usb2_syscon>; + #phy-cells = <0>; + }; + + usb2_syscon: system-controller@5f800 { + compatible = "marvell,armada-3700-usb2-host-misc", "syscon"; + reg = <0x5f800 0x800>; + }; diff --git a/Documentation/devicetree/bindings/phy/marvell,armada-cp110-utmi-phy.yaml b/Documentation/devicetree/bindings/phy/marvell,armada-cp110-utmi-phy.yaml new file mode 100644 index 000000000..9ce7b4c6d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/marvell,armada-cp110-utmi-phy.yaml @@ -0,0 +1,109 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) + +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/marvell,armada-cp110-utmi-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell Armada CP110/CP115 UTMI PHY + +maintainers: + - Konstantin Porotchkin <kostap@marvell.com> + +description: + On Armada 7k/8k and CN913x, there are two host and one device USB controllers. + Each of two exiting UTMI PHYs could be connected to either USB host or USB device + controller. + The USB device controller can only be connected to a single UTMI PHY port + 0.H----- USB HOST0 + UTMI PHY0 --------/ + 0.D-----0 + \------ USB DEVICE + 1.D-----1 + UTMI PHY1 --------\ + 1.H----- USB HOST1 + +properties: + compatible: + const: marvell,cp110-utmi-phy + + reg: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + marvell,system-controller: + description: + Phandle to the system controller node + $ref: /schemas/types.yaml#/definitions/phandle + +# Required child nodes: + +patternProperties: + "^usb-phy@[0|1]$": + type: object + description: + Each UTMI PHY port must be represented as a sub-node. + + properties: + reg: + description: phy port index. + maxItems: 1 + + "#phy-cells": + const: 0 + + required: + - reg + - "#phy-cells" + + additionalProperties: false + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - marvell,system-controller + +additionalProperties: false + +examples: + - | + cp0_utmi: utmi@580000 { + compatible = "marvell,cp110-utmi-phy"; + reg = <0x580000 0x2000>; + marvell,system-controller = <&cp0_syscon0>; + #address-cells = <1>; + #size-cells = <0>; + + cp0_utmi0: usb-phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + + cp0_utmi1: usb-phy@1 { + reg = <1>; + #phy-cells = <0>; + }; + }; + + cp0_usb3_0 { + usb-phy = <&cp0_usb3_0_phy0>; + phys = <&cp0_utmi0>; + phy-names = "utmi"; + /* UTMI0 is connected to USB host controller (default mode) */ + dr_mode = "host"; + }; + + cp0_usb3_1 { + usb-phy = <&cp0_usb3_0_phy1>; + phys = <&cp0_utmi1>; + phy-names = "utmi"; + /* UTMI1 is connected to USB device controller */ + dr_mode = "peripheral"; + }; diff --git a/Documentation/devicetree/bindings/phy/marvell,mmp3-hsic-phy.yaml b/Documentation/devicetree/bindings/phy/marvell,mmp3-hsic-phy.yaml new file mode 100644 index 000000000..bd3bd2f8b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/marvell,mmp3-hsic-phy.yaml @@ -0,0 +1,37 @@ +# SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause) +# Copyright 2019 Lubomir Rintel <lkundrak@v3.sk> +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/marvell,mmp3-hsic-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MMP3 HSIC PHY + +maintainers: + - Lubomir Rintel <lkundrak@v3.sk> + +properties: + compatible: + const: marvell,mmp3-hsic-phy + + reg: + maxItems: 1 + description: base address of the device + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - "#phy-cells" + +additionalProperties: false + +examples: + - | + hsic-phy@f0001800 { + compatible = "marvell,mmp3-hsic-phy"; + reg = <0xf0001800 0x40>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/marvell,mmp3-usb-phy.yaml b/Documentation/devicetree/bindings/phy/marvell,mmp3-usb-phy.yaml new file mode 100644 index 000000000..be13113f7 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/marvell,mmp3-usb-phy.yaml @@ -0,0 +1,42 @@ +# SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause) +# Copyright 2019,2020 Lubomir Rintel <lkundrak@v3.sk> +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/marvell,mmp3-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Marvell MMP3 USB PHY + +maintainers: + - Lubomir Rintel <lkundrak@v3.sk> + +properties: + $nodename: + pattern: '^usb-phy@[a-f0-9]+$' + + compatible: + const: marvell,mmp3-usb-phy + + reg: + maxItems: 1 + description: base address of the device + + '#phy-cells': + const: 0 + +required: + - compatible + - reg + - '#phy-cells' + +additionalProperties: false + +examples: + - | + usb-phy@d4207000 { + compatible = "marvell,mmp3-usb-phy"; + reg = <0xd4207000 0x40>; + #phy-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/mediatek,dsi-phy.yaml b/Documentation/devicetree/bindings/phy/mediatek,dsi-phy.yaml new file mode 100644 index 000000000..a63b20dfa --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mediatek,dsi-phy.yaml @@ -0,0 +1,96 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/mediatek,dsi-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek MIPI Display Serial Interface (DSI) PHY + +maintainers: + - Chun-Kuang Hu <chunkuang.hu@kernel.org> + - Philipp Zabel <p.zabel@pengutronix.de> + - Chunfeng Yun <chunfeng.yun@mediatek.com> + +description: The MIPI DSI PHY supports up to 4-lane output. + +properties: + $nodename: + pattern: "^dsi-phy@[0-9a-f]+$" + + compatible: + oneOf: + - items: + - enum: + - mediatek,mt7623-mipi-tx + - const: mediatek,mt2701-mipi-tx + - items: + - enum: + - mediatek,mt6795-mipi-tx + - const: mediatek,mt8173-mipi-tx + - items: + - enum: + - mediatek,mt8365-mipi-tx + - const: mediatek,mt8183-mipi-tx + - const: mediatek,mt2701-mipi-tx + - const: mediatek,mt8173-mipi-tx + - const: mediatek,mt8183-mipi-tx + + reg: + maxItems: 1 + + clocks: + items: + - description: PLL reference clock + + clock-output-names: + maxItems: 1 + + "#phy-cells": + const: 0 + + "#clock-cells": + const: 0 + + nvmem-cells: + maxItems: 1 + description: A phandle to the calibration data provided by a nvmem device, + if unspecified, default values shall be used. + + nvmem-cell-names: + items: + - const: calibration-data + + drive-strength-microamp: + description: adjust driving current + multipleOf: 200 + minimum: 2000 + maximum: 6000 + default: 4600 + +required: + - compatible + - reg + - clocks + - clock-output-names + - "#phy-cells" + - "#clock-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8173-clk.h> + dsi-phy@10215000 { + compatible = "mediatek,mt8173-mipi-tx"; + reg = <0x10215000 0x1000>; + clocks = <&clk26m>; + clock-output-names = "mipi_tx0_pll"; + drive-strength-microamp = <4000>; + nvmem-cells = <&mipi_tx_calibration>; + nvmem-cell-names = "calibration-data"; + #clock-cells = <0>; + #phy-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/mediatek,hdmi-phy.yaml b/Documentation/devicetree/bindings/phy/mediatek,hdmi-phy.yaml new file mode 100644 index 000000000..f3a8b0b74 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mediatek,hdmi-phy.yaml @@ -0,0 +1,96 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/mediatek,hdmi-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek High Definition Multimedia Interface (HDMI) PHY + +maintainers: + - Chun-Kuang Hu <chunkuang.hu@kernel.org> + - Philipp Zabel <p.zabel@pengutronix.de> + - Chunfeng Yun <chunfeng.yun@mediatek.com> + +description: | + The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel + output and drives the HDMI pads. + +properties: + $nodename: + pattern: "^hdmi-phy@[0-9a-f]+$" + + compatible: + oneOf: + - items: + - enum: + - mediatek,mt7623-hdmi-phy + - const: mediatek,mt2701-hdmi-phy + - const: mediatek,mt2701-hdmi-phy + - const: mediatek,mt8173-hdmi-phy + - const: mediatek,mt8195-hdmi-phy + + reg: + maxItems: 1 + + clocks: + items: + - description: PLL reference clock + + clock-names: + items: + - const: pll_ref + + clock-output-names: + items: + - const: hdmitx_dig_cts + + "#phy-cells": + const: 0 + + "#clock-cells": + const: 0 + + mediatek,ibias: + description: + TX DRV bias current for < 1.65Gbps + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 63 + default: 0xa + + mediatek,ibias_up: + description: + TX DRV bias current for >= 1.65Gbps + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 63 + default: 0x1c + +required: + - compatible + - reg + - clocks + - clock-names + - clock-output-names + - "#phy-cells" + - "#clock-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8173-clk.h> + hdmi_phy: hdmi-phy@10209100 { + compatible = "mediatek,mt8173-hdmi-phy"; + reg = <0x10209100 0x24>; + clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>; + clock-names = "pll_ref"; + clock-output-names = "hdmitx_dig_cts"; + mediatek,ibias = <0xa>; + mediatek,ibias_up = <0x1c>; + #clock-cells = <0>; + #phy-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/mediatek,mt7621-pci-phy.yaml b/Documentation/devicetree/bindings/phy/mediatek,mt7621-pci-phy.yaml new file mode 100644 index 000000000..99eac888a --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mediatek,mt7621-pci-phy.yaml @@ -0,0 +1,41 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/mediatek,mt7621-pci-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek Mt7621 PCIe PHY + +maintainers: + - Sergio Paracuellos <sergio.paracuellos@gmail.com> + +properties: + compatible: + const: mediatek,mt7621-pci-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + "#phy-cells": + const: 1 + description: selects if the phy is dual-ported + +required: + - compatible + - reg + - clocks + - "#phy-cells" + +additionalProperties: false + +examples: + - | + pcie0_phy: pcie-phy@1e149000 { + compatible = "mediatek,mt7621-pci-phy"; + reg = <0x1e149000 0x0700>; + clocks = <&sysc 0>; + #phy-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/phy/mediatek,pcie-phy.yaml b/Documentation/devicetree/bindings/phy/mediatek,pcie-phy.yaml new file mode 100644 index 000000000..422750cc4 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mediatek,pcie-phy.yaml @@ -0,0 +1,75 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/mediatek,pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek PCIe PHY + +maintainers: + - Jianjun Wang <jianjun.wang@mediatek.com> + +description: | + The PCIe PHY supports physical layer functionality for PCIe Gen3 port. + +properties: + compatible: + const: mediatek,mt8195-pcie-phy + + reg: + maxItems: 1 + + reg-names: + items: + - const: sif + + "#phy-cells": + const: 0 + + nvmem-cells: + maxItems: 7 + description: + Phandles to nvmem cell that contains the efuse data, if unspecified, + default value is used. + + nvmem-cell-names: + items: + - const: glb_intr + - const: tx_ln0_pmos + - const: tx_ln0_nmos + - const: rx_ln0 + - const: tx_ln1_pmos + - const: tx_ln1_nmos + - const: rx_ln1 + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - reg-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + phy@11e80000 { + compatible = "mediatek,mt8195-pcie-phy"; + #phy-cells = <0>; + reg = <0x11e80000 0x10000>; + reg-names = "sif"; + nvmem-cells = <&pciephy_glb_intr>, + <&pciephy_tx_ln0_pmos>, + <&pciephy_tx_ln0_nmos>, + <&pciephy_rx_ln0>, + <&pciephy_tx_ln1_pmos>, + <&pciephy_tx_ln1_nmos>, + <&pciephy_rx_ln1>; + nvmem-cell-names = "glb_intr", "tx_ln0_pmos", + "tx_ln0_nmos", "rx_ln0", + "tx_ln1_pmos", "tx_ln1_nmos", + "rx_ln1"; + power-domains = <&spm 2>; + }; diff --git a/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml new file mode 100644 index 000000000..2bb91542e --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mediatek,tphy.yaml @@ -0,0 +1,313 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/mediatek,tphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek T-PHY Controller + +maintainers: + - Chunfeng Yun <chunfeng.yun@mediatek.com> + +description: | + The T-PHY controller supports physical layer functionality for a number of + controllers on MediaTek SoCs, includes USB2.0, USB3.0, PCIe and SATA. + + Layout differences of banks between T-PHY V1 (mt8173/mt2701) and + T-PHY V2 (mt2712) / V3 (mt8195) when works on USB mode: + ----------------------------------- + Version 1: + port offset bank + shared 0x0000 SPLLC + 0x0100 FMREG + u2 port0 0x0800 U2PHY_COM + u3 port0 0x0900 U3PHYD + 0x0a00 U3PHYD_BANK2 + 0x0b00 U3PHYA + 0x0c00 U3PHYA_DA + u2 port1 0x1000 U2PHY_COM + u3 port1 0x1100 U3PHYD + 0x1200 U3PHYD_BANK2 + 0x1300 U3PHYA + 0x1400 U3PHYA_DA + u2 port2 0x1800 U2PHY_COM + ... + + Version 2/3: + port offset bank + u2 port0 0x0000 MISC + 0x0100 FMREG + 0x0300 U2PHY_COM + u3 port0 0x0700 SPLLC + 0x0800 CHIP + 0x0900 U3PHYD + 0x0a00 U3PHYD_BANK2 + 0x0b00 U3PHYA + 0x0c00 U3PHYA_DA + u2 port1 0x1000 MISC + 0x1100 FMREG + 0x1300 U2PHY_COM + u3 port1 0x1700 SPLLC + 0x1800 CHIP + 0x1900 U3PHYD + 0x1a00 U3PHYD_BANK2 + 0x1b00 U3PHYA + 0x1c00 U3PHYA_DA + u2 port2 0x2000 MISC + ... + + SPLLC shared by u3 ports and FMREG shared by u2 ports on V1 are put back + into each port; a new bank MISC for u2 ports and CHIP for u3 ports are + added on V2; the FMREG bank for slew rate calibration is not used anymore + and reserved on V3; + +properties: + $nodename: + pattern: "^t-phy(@[0-9a-f]+)?$" + + compatible: + oneOf: + - items: + - enum: + - mediatek,mt2701-tphy + - mediatek,mt7623-tphy + - mediatek,mt7622-tphy + - mediatek,mt8516-tphy + - const: mediatek,generic-tphy-v1 + - items: + - enum: + - mediatek,mt2712-tphy + - mediatek,mt7629-tphy + - mediatek,mt7986-tphy + - mediatek,mt8183-tphy + - mediatek,mt8186-tphy + - mediatek,mt8192-tphy + - mediatek,mt8365-tphy + - const: mediatek,generic-tphy-v2 + - items: + - enum: + - mediatek,mt8188-tphy + - mediatek,mt8195-tphy + - const: mediatek,generic-tphy-v3 + - const: mediatek,mt2701-u3phy + deprecated: true + - const: mediatek,mt2712-u3phy + deprecated: true + - const: mediatek,mt8173-u3phy + + reg: + description: + Register shared by multiple ports, exclude port's private register. + It is needed for T-PHY V1, such as mt2701 and mt8173, but not for + T-PHY V2/V3, such as mt2712. + maxItems: 1 + + "#address-cells": + enum: [1, 2] + + "#size-cells": + enum: [1, 2] + + # Used with non-empty value if optional 'reg' is not provided. + # The format of the value is an arbitrary number of triplets of + # (child-bus-address, parent-bus-address, length). + ranges: true + + mediatek,src-ref-clk-mhz: + description: + Frequency of reference clock for slew rate calibrate + default: 26 + + mediatek,src-coef: + description: + Coefficient for slew rate calibrate, depends on SoC process + $ref: /schemas/types.yaml#/definitions/uint32 + default: 28 + +# Required child node: +patternProperties: + "^(usb|pcie|sata)-phy@[0-9a-f]+$": + type: object + description: + A sub-node is required for each port the controller provides. + Address range information including the usual 'reg' property + is used inside these nodes to describe the controller's topology. + + properties: + reg: + maxItems: 1 + + clocks: + minItems: 1 + items: + - description: Reference clock, (HS is 48Mhz, SS/P is 24~27Mhz) + - description: Reference clock of analog phy + description: + Uses both clocks if the clock of analog and digital phys are + separated, otherwise uses "ref" clock only if needed. + + clock-names: + minItems: 1 + items: + - const: ref + - const: da_ref + + "#phy-cells": + const: 1 + description: | + The cells contain the following arguments. + + - description: The PHY type + enum: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + - PHY_TYPE_PCIE + - PHY_TYPE_SATA + - PHY_TYPE_SGMII + + nvmem-cells: + items: + - description: internal R efuse for U2 PHY or U3/PCIe PHY + - description: rx_imp_sel efuse for U3/PCIe PHY + - description: tx_imp_sel efuse for U3/PCIe PHY + description: | + Phandles to nvmem cell that contains the efuse data; + Available only for U2 PHY or U3/PCIe PHY of version 2/3, these + three items should be provided at the same time for U3/PCIe PHY, + when use software to load efuse; + If unspecified, will use hardware auto-load efuse. + + nvmem-cell-names: + items: + - const: intr + - const: rx_imp + - const: tx_imp + + # The following optional vendor properties are only for debug or HQA test + mediatek,eye-src: + description: + The value of slew rate calibrate (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 7 + + mediatek,eye-vrt: + description: + The selection of VRT reference voltage (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 7 + + mediatek,eye-term: + description: + The selection of HS_TX TERM reference voltage (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 7 + + mediatek,intr: + description: + The selection of internal resistor (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 31 + + mediatek,discth: + description: + The selection of disconnect threshold (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 15 + + mediatek,pre-emphasis: + description: + The level of pre-emphasis which used to widen the eye opening and + boost eye swing, the unit step is about 4.16% increment; e.g. the + level 1 means amplitude increases about 4.16%, the level 2 is about + 8.3% etc. (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 3 + + mediatek,bc12: + description: + Specify the flag to enable BC1.2 if support it + type: boolean + + mediatek,syscon-type: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + description: + A phandle to syscon used to access the register of type switch, + the field should always be 3 cells long. + items: + items: + - description: + The first cell represents a phandle to syscon + - description: + The second cell represents the register offset + - description: + The third cell represents the index of config segment + enum: [0, 1, 2, 3] + + required: + - reg + - "#phy-cells" + + additionalProperties: false + +required: + - compatible + - "#address-cells" + - "#size-cells" + - ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8173-clk.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/phy/phy.h> + usb@11271000 { + compatible = "mediatek,mt8173-mtu3", "mediatek,mtu3"; + reg = <0x11271000 0x3000>, <0x11280700 0x0100>; + reg-names = "mac", "ippc"; + phys = <&u2port0 PHY_TYPE_USB2>, + <&u3port0 PHY_TYPE_USB3>, + <&u2port1 PHY_TYPE_USB2>; + interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>; + clocks = <&topckgen CLK_TOP_USB30_SEL>; + clock-names = "sys_ck"; + }; + + t-phy@11290000 { + compatible = "mediatek,mt8173-u3phy"; + reg = <0x11290000 0x800>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + u2port0: usb-phy@11290800 { + reg = <0x11290800 0x100>; + clocks = <&apmixedsys CLK_APMIXED_REF2USB_TX>, <&clk48m>; + clock-names = "ref", "da_ref"; + #phy-cells = <1>; + }; + + u3port0: usb-phy@11290900 { + reg = <0x11290900 0x700>; + clocks = <&clk26m>; + clock-names = "ref"; + #phy-cells = <1>; + }; + + u2port1: usb-phy@11291000 { + reg = <0x11291000 0x100>; + #phy-cells = <1>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/mediatek,ufs-phy.yaml b/Documentation/devicetree/bindings/phy/mediatek,ufs-phy.yaml new file mode 100644 index 000000000..3e62b5d4d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mediatek,ufs-phy.yaml @@ -0,0 +1,69 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/mediatek,ufs-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek Universal Flash Storage (UFS) M-PHY + +maintainers: + - Stanley Chu <stanley.chu@mediatek.com> + - Chunfeng Yun <chunfeng.yun@mediatek.com> + +description: | + UFS M-PHY nodes are defined to describe on-chip UFS M-PHY hardware macro. + Each UFS M-PHY node should have its own node. + To bind UFS M-PHY with UFS host controller, the controller node should + contain a phandle reference to UFS M-PHY node. + +properties: + $nodename: + pattern: "^ufs-phy@[0-9a-f]+$" + + compatible: + oneOf: + - items: + - enum: + - mediatek,mt8195-ufsphy + - const: mediatek,mt8183-ufsphy + - const: mediatek,mt8183-ufsphy + + reg: + maxItems: 1 + + clocks: + items: + - description: Unipro core control clock. + - description: M-PHY core control clock. + + clock-names: + items: + - const: unipro + - const: mp + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/mt8183-clk.h> + ufsphy: ufs-phy@11fa0000 { + compatible = "mediatek,mt8183-ufsphy"; + reg = <0x11fa0000 0xc000>; + clocks = <&infracfg CLK_INFRA_UNIPRO_SCK>, + <&infracfg CLK_INFRA_UFS_MP_SAP_BCLK>; + clock-names = "unipro", "mp"; + #phy-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/mediatek,xsphy.yaml b/Documentation/devicetree/bindings/phy/mediatek,xsphy.yaml new file mode 100644 index 000000000..a9e3139fd --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mediatek,xsphy.yaml @@ -0,0 +1,199 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (c) 2020 MediaTek +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/mediatek,xsphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek XS-PHY Controller + +maintainers: + - Chunfeng Yun <chunfeng.yun@mediatek.com> + +description: | + The XS-PHY controller supports physical layer functionality for USB3.1 + GEN2 controller on MediaTek SoCs. + + Banks layout of xsphy + ---------------------------------- + port offset bank + u2 port0 0x0000 MISC + 0x0100 FMREG + 0x0300 U2PHY_COM + u2 port1 0x1000 MISC + 0x1100 FMREG + 0x1300 U2PHY_COM + u2 port2 0x2000 MISC + ... + u31 common 0x3000 DIG_GLB + 0x3100 PHYA_GLB + u31 port0 0x3400 DIG_LN_TOP + 0x3500 DIG_LN_TX0 + 0x3600 DIG_LN_RX0 + 0x3700 DIG_LN_DAIF + 0x3800 PHYA_LN + u31 port1 0x3a00 DIG_LN_TOP + 0x3b00 DIG_LN_TX0 + 0x3c00 DIG_LN_RX0 + 0x3d00 DIG_LN_DAIF + 0x3e00 PHYA_LN + ... + DIG_GLB & PHYA_GLB are shared by U31 ports. + +properties: + $nodename: + pattern: "^xs-phy@[0-9a-f]+$" + + compatible: + items: + - enum: + - mediatek,mt3611-xsphy + - mediatek,mt3612-xsphy + - const: mediatek,xsphy + + reg: + description: + Register shared by multiple U3 ports, exclude port's private register, + if only U2 ports provided, shouldn't use the property. + maxItems: 1 + + "#address-cells": + enum: [1, 2] + + "#size-cells": + enum: [1, 2] + + ranges: true + + mediatek,src-ref-clk-mhz: + description: + Frequency of reference clock for slew rate calibrate + default: 26 + + mediatek,src-coef: + description: + Coefficient for slew rate calibrate, depends on SoC process + $ref: /schemas/types.yaml#/definitions/uint32 + default: 17 + +# Required child node: +patternProperties: + "^usb-phy@[0-9a-f]+$": + type: object + description: + A sub-node is required for each port the controller provides. + Address range information including the usual 'reg' property + is used inside these nodes to describe the controller's topology. + + properties: + reg: + maxItems: 1 + + clocks: + items: + - description: Reference clock, (HS is 48Mhz, SS/P is 24~27Mhz) + + clock-names: + items: + - const: ref + + "#phy-cells": + const: 1 + description: | + The cells contain the following arguments. + + - description: The PHY type + enum: + - PHY_TYPE_USB2 + - PHY_TYPE_USB3 + + # The following optional vendor properties are only for debug or HQA test + mediatek,eye-src: + description: + The value of slew rate calibrate (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 7 + + mediatek,eye-vrt: + description: + The selection of VRT reference voltage (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 7 + + mediatek,eye-term: + description: + The selection of HS_TX TERM reference voltage (U2 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 7 + + mediatek,efuse-intr: + description: + The selection of Internal Resistor (U2/U3 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 63 + + mediatek,efuse-tx-imp: + description: + The selection of TX Impedance (U3 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 31 + + mediatek,efuse-rx-imp: + description: + The selection of RX Impedance (U3 phy) + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 31 + + required: + - reg + - clocks + - clock-names + - "#phy-cells" + + additionalProperties: false + +required: + - compatible + - "#address-cells" + - "#size-cells" + - ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/phy/phy.h> + + u3phy: xs-phy@11c40000 { + compatible = "mediatek,mt3611-xsphy", "mediatek,xsphy"; + reg = <0x11c43000 0x0200>; + mediatek,src-ref-clk-mhz = <26>; + mediatek,src-coef = <17>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + u2port0: usb-phy@11c40000 { + reg = <0x11c40000 0x0400>; + clocks = <&clk48m>; + clock-names = "ref"; + mediatek,eye-src = <4>; + #phy-cells = <1>; + }; + + u3port0: usb-phy@11c43000 { + reg = <0x11c43400 0x0500>; + clocks = <&clk26m>; + clock-names = "ref"; + mediatek,efuse-intr = <28>; + #phy-cells = <1>; + }; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/microchip,lan966x-serdes.yaml b/Documentation/devicetree/bindings/phy/microchip,lan966x-serdes.yaml new file mode 100644 index 000000000..6e914fbba --- /dev/null +++ b/Documentation/devicetree/bindings/phy/microchip,lan966x-serdes.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/microchip,lan966x-serdes.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip Lan966x Serdes controller + +maintainers: + - Horatiu Vultur <horatiu.vultur@microchip.com> + +description: | + Lan966x has 7 interfaces, consisting of 2 copper transceivers(CU), + 3 SERDES6G and 2 RGMII interfaces. Two of the SERDES6G support QSGMII. + Also it has 8 logical Ethernet ports which can be connected to these + interfaces. The Serdes controller will allow to configure these interfaces + and allows to "mux" the interfaces to different ports. + + For simple selection of the interface that is used with a port, the + following macros are defined CU(X), SERDES6G(X), RGMII(X). Where X is a + number that represents the index of that interface type. For example + CU(1) means use interface copper transceivers 1. SERDES6G(2) means use + interface SerDes 2. + +properties: + $nodename: + pattern: "^serdes@[0-9a-f]+$" + + compatible: + const: microchip,lan966x-serdes + + reg: + items: + - description: HSIO registers + - description: HW_STAT register + + '#phy-cells': + const: 2 + description: | + - Input port to use for a given macro. + - The macro to be used. The macros are defined in + dt-bindings/phy/phy-lan966x-serdes. + +required: + - compatible + - reg + - '#phy-cells' + +additionalProperties: false + +examples: + - | + serdes: serdes@e2004010 { + compatible = "microchip,lan966x-serdes"; + reg = <0xe202c000 0x9c>, <0xe2004010 0x4>; + #phy-cells = <2>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml b/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml new file mode 100644 index 000000000..bdbdb3bbd --- /dev/null +++ b/Documentation/devicetree/bindings/phy/microchip,sparx5-serdes.yaml @@ -0,0 +1,100 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/microchip,sparx5-serdes.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microchip Sparx5 Serdes controller + +maintainers: + - Steen Hegelund <steen.hegelund@microchip.com> + +description: | + The Sparx5 SERDES interfaces share the same basic functionality, but + support different operating modes and line rates. + + The following list lists the SERDES features: + + * RX Adaptive Decision Feedback Equalizer (DFE) + * Programmable continuous time linear equalizer (CTLE) + * Rx variable gain control + * Rx built-in fault detector (loss-of-lock/loss-of-signal) + * Adjustable tx de-emphasis (FFE) + * Tx output amplitude control + * Supports rx eye monitor + * Multiple loopback modes + * Prbs generator and checker + * Polarity inversion control + + SERDES6G: + + The SERDES6G is a high-speed SERDES interface, which can operate at + the following data rates: + + * 100 Mbps (100BASE-FX) + * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX) + * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX) + * 5.15625 Gbps (5GBASE-KR/5G-USXGMII) + + SERDES10G + + The SERDES10G is a high-speed SERDES interface, which can operate at + the following data rates: + + * 100 Mbps (100BASE-FX) + * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX) + * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX) + * 5 Gbps (QSGMII/USGMII) + * 5.15625 Gbps (5GBASE-KR/5G-USXGMII) + * 10 Gbps (10G-USGMII) + * 10.3125 Gbps (10GBASE-R/10GBASE-KR/USXGMII) + + SERDES25G + + The SERDES25G is a high-speed SERDES interface, which can operate at + the following data rates: + + * 1.25 Gbps (SGMII/1000BASE-X/1000BASE-KX) + * 3.125 Gbps (2.5GBASE-X/2.5GBASE-KX) + * 5 Gbps (QSGMII/USGMII) + * 5.15625 Gbps (5GBASE-KR/5G-USXGMII) + * 10 Gbps (10G-USGMII) + * 10.3125 Gbps (10GBASE-R/10GBASE-KR/USXGMII) + * 25.78125 Gbps (25GBASE-KR/25GBASE-CR/25GBASE-SR/25GBASE-LR/25GBASE-ER) + +properties: + $nodename: + pattern: "^serdes@[0-9a-f]+$" + + compatible: + const: microchip,sparx5-serdes + + reg: + minItems: 1 + + '#phy-cells': + const: 1 + description: | + - The main serdes input port + + clocks: + maxItems: 1 + +required: + - compatible + - reg + - '#phy-cells' + - clocks + +additionalProperties: false + +examples: + - | + serdes: serdes@10808000 { + compatible = "microchip,sparx5-serdes"; + #phy-cells = <1>; + clocks = <&sys_clk>; + reg = <0x10808000 0x5d0000>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/mixel,mipi-dsi-phy.yaml b/Documentation/devicetree/bindings/phy/mixel,mipi-dsi-phy.yaml new file mode 100644 index 000000000..3c28ec50f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mixel,mipi-dsi-phy.yaml @@ -0,0 +1,98 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/mixel,mipi-dsi-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mixel DSI PHY for i.MX8 + +maintainers: + - Guido GĂŒnther <agx@sigxcpu.org> + +description: | + The Mixel MIPI-DSI PHY IP block is e.g. found on i.MX8 platforms (along the + MIPI-DSI IP from Northwest Logic). It represents the physical layer for the + electrical signals for DSI. + + The Mixel PHY IP block found on i.MX8qxp is a combo PHY that can work + in either MIPI-DSI PHY mode or LVDS PHY mode. + +properties: + compatible: + enum: + - fsl,imx8mq-mipi-dphy + - fsl,imx8qxp-mipi-dphy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: phy_ref + + "#phy-cells": + const: 0 + + fsl,syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: | + A phandle which points to Control and Status Registers(CSR) module. + + power-domains: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - "#phy-cells" + - power-domains + +allOf: + - if: + properties: + compatible: + contains: + const: fsl,imx8mq-mipi-dphy + then: + properties: + fsl,syscon: false + + required: + - assigned-clocks + - assigned-clock-parents + - assigned-clock-rates + + - if: + properties: + compatible: + contains: + const: fsl,imx8qxp-mipi-dphy + then: + properties: + assigned-clocks: false + assigned-clock-parents: false + assigned-clock-rates: false + + required: + - fsl,syscon + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/imx8mq-clock.h> + dphy: dphy@30a0030 { + compatible = "fsl,imx8mq-mipi-dphy"; + reg = <0x30a00300 0x100>; + clocks = <&clk IMX8MQ_CLK_DSI_PHY_REF>; + clock-names = "phy_ref"; + assigned-clocks = <&clk IMX8MQ_CLK_DSI_PHY_REF>; + assigned-clock-parents = <&clk IMX8MQ_VIDEO_PLL1_OUT>; + assigned-clock-rates = <24000000>; + #phy-cells = <0>; + power-domains = <&pgc_mipi>; + }; diff --git a/Documentation/devicetree/bindings/phy/mscc,vsc7514-serdes.yaml b/Documentation/devicetree/bindings/phy/mscc,vsc7514-serdes.yaml new file mode 100644 index 000000000..3169b8732 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/mscc,vsc7514-serdes.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/mscc,vsc7514-serdes.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Microsemi Ocelot SerDes muxing + +maintainers: + - Alexandre Belloni <alexandre.belloni@bootlin.com> + - UNGLinuxDriver@microchip.com + +description: | + On Microsemi Ocelot, there is a handful of registers in HSIO address + space for setting up the SerDes to switch port muxing. + + A SerDes X can be "muxed" to work with switch port Y or Z for example. + One specific SerDes can also be used as a PCIe interface. + + Hence, a SerDes represents an interface, be it an Ethernet or a PCIe one. + + There are two kinds of SerDes: SERDES1G supports 10/100Mbps in + half/full-duplex and 1000Mbps in full-duplex mode while SERDES6G supports + 10/100Mbps in half/full-duplex and 1000/2500Mbps in full-duplex mode. + + Also, SERDES6G number (aka "macro") 0 is the only interface supporting + QSGMII. + + This is a child of the HSIO syscon ("mscc,ocelot-hsio", see + Documentation/devicetree/bindings/mips/mscc.txt) on the Microsemi Ocelot. + +properties: + compatible: + enum: + - mscc,vsc7514-serdes + + "#phy-cells": + const: 2 + description: | + The first number defines the input port to use for a given SerDes macro. + The second defines the macro to use. They are defined in + dt-bindings/phy/phy-ocelot-serdes.h + +required: + - compatible + - "#phy-cells" + +additionalProperties: + false + +examples: + - | + serdes: serdes { + compatible = "mscc,vsc7514-serdes"; + #phy-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.yaml b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.yaml new file mode 100644 index 000000000..33b41b6b2 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra124-xusb-padctl.yaml @@ -0,0 +1,654 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/nvidia,tegra124-xusb-padctl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra124 XUSB pad controller + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + +description: | + The Tegra XUSB pad controller manages a set of I/O lanes (with differential + signals) which connect directly to pins/pads on the SoC package. Each lane + is controlled by a HW block referred to as a "pad" in the Tegra hardware + documentation. Each such "pad" may control either one or multiple lanes, + and thus contains any logic common to all its lanes. Each lane can be + separately configured and powered up. + + Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or + super-speed USB. Other lanes are for various types of low-speed, full-speed + or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller + contains a software-configurable mux that sits between the I/O controller + ports (e.g. PCIe) and the lanes. + + In addition to per-lane configuration, USB 3.0 ports may require additional + settings on a per-board basis. + + Pads will be represented as children of the top-level XUSB pad controller + device tree node. Each lane exposed by the pad will be represented by its + own subnode and can be referenced by users of the lane using the standard + PHY bindings, as described by the phy-bindings.txt file in this directory. + + The Tegra hardware documentation refers to the connection between the XUSB + pad controller and the XUSB controller as "ports". This is confusing since + "port" is typically used to denote the physical USB receptacle. The device + tree binding in this document uses the term "port" to refer to the logical + abstraction of the signals that are routed to a USB receptacle (i.e. a PHY + for the USB signal, the VBUS power supply, the USB 2.0 companion port for + USB 3.0 receptacles, ...). + +properties: + compatible: + oneOf: + - enum: + - nvidia,tegra124-xusb-padctl + + - items: + - const: nvidia,tegra132-xusb-padctl + - const: nvidia,tegra124-xusb-padctl + + reg: + maxItems: 1 + + interrupts: + items: + - description: XUSB pad controller interrupt + + resets: + items: + - description: pad controller reset + + reset-names: + items: + - const: padctl + + avdd-pll-utmip-supply: + description: UTMI PLL power supply. Must supply 1.8 V. + + avdd-pll-erefe-supply: + description: PLLE reference PLL power supply. Must supply 1.05 V. + + avdd-pex-pll-supply: + description: PCIe/USB3 PLL power supply. Must supply 1.05 V. + + hvdd-pex-pll-e-supply: + description: High-voltage PLLE power supply. Must supply 3.3 V. + + pads: + description: A required child node named "pads" contains a list of + subnodes, one for each of the pads exposed by the XUSB pad controller. + Each pad may need additional resources that can be referenced in its + pad node. + + The "status" property is used to enable or disable the use of a pad. + If set to "disabled", the pad will not be used on the given board. In + order to use the pad and any of its lanes, this property must be set + to "okay" or be absent. + type: object + additionalProperties: false + properties: + usb2: + type: object + additionalProperties: false + properties: + clocks: + items: + - description: USB2 tracking clock + + clock-names: + items: + - const: trk + + lanes: + type: object + additionalProperties: false + properties: + usb2-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb, uart ] + + usb2-1: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb, uart ] + + usb2-2: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb, uart ] + + ulpi: + type: object + additionalProperties: false + properties: + lanes: + type: object + additionalProperties: false + properties: + ulpi-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb ] + + hsic: + type: object + additionalProperties: false + properties: + clocks: + items: + - description: HSIC tracking clock + + clock-names: + items: + - const: trk + + lanes: + type: object + additionalProperties: false + properties: + hsic-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb ] + + hsic-1: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb ] + + pcie: + type: object + additionalProperties: false + properties: + clocks: + items: + - description: PLLE clock + + clock-names: + items: + - const: pll + + resets: + items: + - description: reset for the PCIe UPHY block + + reset-names: + items: + - const: phy + + lanes: + type: object + additionalProperties: false + properties: + pcie-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie, usb3-ss ] + + pcie-1: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie, usb3-ss ] + + pcie-2: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie, usb3-ss ] + + pcie-3: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie, usb3-ss ] + + pcie-4: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie, usb3-ss ] + + sata: + type: object + additionalProperties: false + properties: + resets: + items: + - description: reset for the SATA UPHY block + + reset-names: + items: + - const: phy + + lanes: + type: object + additionalProperties: false + properties: + sata-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ sata, usb3-ss ] + + ports: + description: A required child node named "ports" contains a list of + subnodes, one for each of the ports exposed by the XUSB pad controller. + Each port may need additional resources that can be referenced in its + port node. + + The "status" property is used to enable or disable the use of a port. + If set to "disabled", the port will not be used on the given board. In + order to use the port, this property must be set to "okay". + type: object + additionalProperties: false + properties: + usb2-0: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb2-1: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb2-2: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + ulpi-0: + type: object + additionalProperties: false + properties: + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + hsic-0: + type: object + additionalProperties: false + properties: + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + hsic-1: + type: object + additionalProperties: false + properties: + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb3-0: + type: object + additionalProperties: false + properties: + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb3-1: + type: object + additionalProperties: false + properties: + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + +additionalProperties: false + +required: + - compatible + - reg + - resets + - reset-names + - avdd-pll-utmip-supply + - avdd-pll-erefe-supply + - avdd-pex-pll-supply + - hvdd-pex-pll-e-supply + +examples: + # Tegra124 and Tegra132 + - | + #include <dt-bindings/interrupt-controller/arm-gic.h> + + padctl@7009f000 { + compatible = "nvidia,tegra124-xusb-padctl"; + reg = <0x7009f000 0x1000>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + avdd-pll-utmip-supply = <&vddio_1v8>; + avdd-pll-erefe-supply = <&avdd_1v05_run>; + avdd-pex-pll-supply = <&vdd_1v05_run>; + hvdd-pex-pll-e-supply = <&vdd_3v3_lp0>; + + pads { + usb2 { + lanes { + usb2-0 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + + usb2-1 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + + usb2-2 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + }; + }; + + ulpi { + lanes { + ulpi-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + hsic-1 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + pcie { + lanes { + pcie-0 { + nvidia,function = "usb3-ss"; + #phy-cells = <0>; + }; + + pcie-1 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-2 { + nvidia,function = "pcie"; + #phy-cells = <0>; + }; + + pcie-3 { + status = "disabled"; + #phy-cells = <0>; + }; + + pcie-4 { + nvidia,function = "pcie"; + #phy-cells = <0>; + }; + }; + }; + + sata { + lanes { + sata-0 { + nvidia,function = "sata"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + /* Micro A/B */ + usb2-0 { + mode = "otg"; + }; + + /* Mini PCIe */ + usb2-1 { + mode = "host"; + }; + + /* USB3 */ + usb2-2 { + vbus-supply = <&vdd_usb3_vbus>; + mode = "host"; + }; + + ulpi-0 { + status = "disabled"; + }; + + hsic-0 { + status = "disabled"; + }; + + hsic-1 { + status = "disabled"; + }; + + usb3-0 { + nvidia,usb2-companion = <2>; + }; + + usb3-1 { + status = "disabled"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra186-xusb-padctl.yaml b/Documentation/devicetree/bindings/phy/nvidia,tegra186-xusb-padctl.yaml new file mode 100644 index 000000000..8b1d5a852 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra186-xusb-padctl.yaml @@ -0,0 +1,544 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/nvidia,tegra186-xusb-padctl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra186 XUSB pad controller + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + +description: | + The Tegra XUSB pad controller manages a set of I/O lanes (with differential + signals) which connect directly to pins/pads on the SoC package. Each lane + is controlled by a HW block referred to as a "pad" in the Tegra hardware + documentation. Each such "pad" may control either one or multiple lanes, + and thus contains any logic common to all its lanes. Each lane can be + separately configured and powered up. + + Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or + super-speed USB. Other lanes are for various types of low-speed, full-speed + or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller + contains a software-configurable mux that sits between the I/O controller + ports (e.g. PCIe) and the lanes. + + In addition to per-lane configuration, USB 3.0 ports may require additional + settings on a per-board basis. + + Pads will be represented as children of the top-level XUSB pad controller + device tree node. Each lane exposed by the pad will be represented by its + own subnode and can be referenced by users of the lane using the standard + PHY bindings, as described by the phy-bindings.txt file in this directory. + + The Tegra hardware documentation refers to the connection between the XUSB + pad controller and the XUSB controller as "ports". This is confusing since + "port" is typically used to denote the physical USB receptacle. The device + tree binding in this document uses the term "port" to refer to the logical + abstraction of the signals that are routed to a USB receptacle (i.e. a PHY + for the USB signal, the VBUS power supply, the USB 2.0 companion port for + USB 3.0 receptacles, ...). + +properties: + compatible: + const: nvidia,tegra186-xusb-padctl + + reg: + items: + - description: pad controller registers + - description: AO registers + + interrupts: + items: + - description: XUSB pad controller interrupt + + reg-names: + items: + - const: padctl + - const: ao + + resets: + items: + - description: pad controller reset + + reset-names: + items: + - const: padctl + + avdd-pll-erefeut-supply: + description: UPHY brick and reference clock as well as UTMI PHY + power supply. Must supply 1.8 V. + + avdd-usb-supply: + description: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must + supply 3.3 V. + + vclamp-usb-supply: + description: Bias rail for USB pad. Must supply 1.8 V. + + vddio-hsic-supply: + description: HSIC PHY power supply. Must supply 1.2 V. + + pads: + description: A required child node named "pads" contains a list of + subnodes, one for each of the pads exposed by the XUSB pad controller. + Each pad may need additional resources that can be referenced in its + pad node. + + The "status" property is used to enable or disable the use of a pad. + If set to "disabled", the pad will not be used on the given board. In + order to use the pad and any of its lanes, this property must be set + to "okay" or be absent. + type: object + additionalProperties: false + properties: + usb2: + type: object + additionalProperties: false + properties: + clocks: + items: + - description: USB2 tracking clock + + clock-names: + items: + - const: trk + + lanes: + type: object + additionalProperties: false + properties: + usb2-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb2-1: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb2-2: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + hsic: + type: object + additionalProperties: false + properties: + clocks: + items: + - description: HSIC tracking clock + + clock-names: + items: + - const: trk + + lanes: + type: object + additionalProperties: false + properties: + hsic-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb3: + type: object + additionalProperties: false + properties: + lanes: + type: object + additionalProperties: false + properties: + usb3-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb3-1: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb3-2: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + ports: + description: A required child node named "ports" contains a list of + subnodes, one for each of the ports exposed by the XUSB pad controller. + Each port may need additional resources that can be referenced in its + port node. + + The "status" property is used to enable or disable the use of a port. + If set to "disabled", the port will not be used on the given board. In + order to use the port, this property must be set to "okay". + type: object + additionalProperties: false + properties: + usb2-0: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + dependencies: + usb-role-switch: [ connector ] + + usb2-1: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + dependencies: + usb-role-switch: [ connector ] + + usb2-2: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + dependencies: + usb-role-switch: [ connector ] + + hsic-0: + type: object + additionalProperties: false + + usb3-0: + type: object + additionalProperties: false + properties: + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb3-1: + type: object + additionalProperties: false + properties: + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb3-2: + type: object + additionalProperties: false + properties: + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + +additionalProperties: false + +required: + - compatible + - reg + - resets + - reset-names + - avdd-pll-erefeut-supply + - avdd-usb-supply + - vclamp-usb-supply + - vddio-hsic-supply + +examples: + - | + #include <dt-bindings/clock/tegra186-clock.h> + #include <dt-bindings/gpio/tegra186-gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/reset/tegra186-reset.h> + + padctl@3520000 { + compatible = "nvidia,tegra186-xusb-padctl"; + reg = <0x03520000 0x1000>, + <0x03540000 0x1000>; + reg-names = "padctl", "ao"; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>; + + resets = <&bpmp TEGRA186_RESET_XUSB_PADCTL>; + reset-names = "padctl"; + + avdd-pll-erefeut-supply = <&vdd_1v8_pll>; + avdd-usb-supply = <&vdd_3v3_sys>; + vclamp-usb-supply = <&vdd_1v8>; + vddio-hsic-supply = <&gnd>; + + pads { + usb2 { + clocks = <&bpmp TEGRA186_CLK_USB2_TRK>; + clock-names = "trk"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + + usb2-1 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + + usb2-2 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + clocks = <&bpmp TEGRA186_CLK_HSIC_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + usb3 { + lanes { + usb3-0 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + + usb3-1 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + + usb3-2 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + mode = "otg"; + vbus-supply = <&vdd_usb0>; + usb-role-switch; + + connector { + compatible = "gpio-usb-b-connector", + "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + vbus-gpios = <&gpio TEGRA186_MAIN_GPIO(X, 7) GPIO_ACTIVE_LOW>; + id-gpios = <&pmic 0 GPIO_ACTIVE_HIGH>; + }; + }; + + usb2-1 { + vbus-supply = <&vdd_usb1>; + mode = "host"; + }; + + usb2-2 { + status = "disabled"; + }; + + hsic-0 { + status = "disabled"; + }; + + usb3-0 { + nvidia,usb2-companion = <1>; + }; + + usb3-1 { + status = "disabled"; + }; + + usb3-2 { + status = "disabled"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra194-xusb-padctl.yaml b/Documentation/devicetree/bindings/phy/nvidia,tegra194-xusb-padctl.yaml new file mode 100644 index 000000000..6e3398399 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra194-xusb-padctl.yaml @@ -0,0 +1,632 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/nvidia,tegra194-xusb-padctl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra194 XUSB pad controller + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + +description: | + The Tegra XUSB pad controller manages a set of I/O lanes (with differential + signals) which connect directly to pins/pads on the SoC package. Each lane + is controlled by a HW block referred to as a "pad" in the Tegra hardware + documentation. Each such "pad" may control either one or multiple lanes, + and thus contains any logic common to all its lanes. Each lane can be + separately configured and powered up. + + Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or + super-speed USB. Other lanes are for various types of low-speed, full-speed + or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller + contains a software-configurable mux that sits between the I/O controller + ports (e.g. PCIe) and the lanes. + + In addition to per-lane configuration, USB 3.0 ports may require additional + settings on a per-board basis. + + Pads will be represented as children of the top-level XUSB pad controller + device tree node. Each lane exposed by the pad will be represented by its + own subnode and can be referenced by users of the lane using the standard + PHY bindings, as described by the phy-bindings.txt file in this directory. + + The Tegra hardware documentation refers to the connection between the XUSB + pad controller and the XUSB controller as "ports". This is confusing since + "port" is typically used to denote the physical USB receptacle. The device + tree binding in this document uses the term "port" to refer to the logical + abstraction of the signals that are routed to a USB receptacle (i.e. a PHY + for the USB signal, the VBUS power supply, the USB 2.0 companion port for + USB 3.0 receptacles, ...). + +properties: + compatible: + enum: + - nvidia,tegra194-xusb-padctl + - nvidia,tegra234-xusb-padctl + + reg: + items: + - description: pad controller registers + - description: AO registers + + reg-names: + items: + - const: padctl + - const: ao + + interrupts: + items: + - description: XUSB pad controller interrupt + + resets: + items: + - description: pad controller reset + + reset-names: + items: + - const: padctl + + avdd-usb-supply: + description: USB I/Os, VBUS, ID, REXT, D+/D- power supply. Must + supply 3.3 V. + + vclamp-usb-supply: + description: Bias rail for USB pad. Must supply 1.8 V. + + pads: + description: A required child node named "pads" contains a list of + subnodes, one for each of the pads exposed by the XUSB pad controller. + Each pad may need additional resources that can be referenced in its + pad node. + + The "status" property is used to enable or disable the use of a pad. + If set to "disabled", the pad will not be used on the given board. In + order to use the pad and any of its lanes, this property must be set + to "okay" or absent. + type: object + additionalProperties: false + properties: + usb2: + type: object + additionalProperties: false + properties: + clocks: + items: + - description: USB2 tracking clock + + clock-names: + items: + - const: trk + + lanes: + type: object + additionalProperties: false + properties: + usb2-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb2-1: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb2-2: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb2-3: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb3: + type: object + additionalProperties: false + properties: + lanes: + type: object + additionalProperties: false + properties: + usb3-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb3-1: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb3-2: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + usb3-3: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ xusb ] + + ports: + description: A required child node named "ports" contains a list of + subnodes, one for each of the ports exposed by the XUSB pad controller. + Each port may need additional resources that can be referenced in its + port node. + + The "status" property is used to enable or disable the use of a port. + If set to "disabled", the port will not be used on the given board. In + order to use the port, this property must be set to "okay". + type: object + additionalProperties: false + properties: + usb2-0: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + dependencies: + usb-role-switch: [ connector ] + + usb2-1: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + dependencies: + usb-role-switch: [ connector ] + + usb2-2: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + dependencies: + usb-role-switch: [ connector ] + + usb2-3: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + dependencies: + usb-role-switch: [ connector ] + + usb3-0: + type: object + additionalProperties: false + properties: + maximum-speed: + description: A string property that specifies the maximum + supported speed of a USB3 port. + $ref: /schemas/types.yaml#/definitions/string + oneOf: + - description: The USB3 port supports USB 3.1 Gen 2 speed. + This is the default. + const: super-speed-plus + - description: The USB3 port supports USB 3.1 Gen 1 speed + only. + const: super-speed + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb3-1: + type: object + additionalProperties: false + properties: + maximum-speed: + description: A string property that specifies the maximum + supported speed of a USB3 port. + $ref: /schemas/types.yaml#/definitions/string + oneOf: + - description: The USB3 port supports USB 3.1 Gen 2 speed. + This is the default. + const: super-speed-plus + - description: The USB3 port supports USB 3.1 Gen 1 speed + only. + const: super-speed + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb3-2: + type: object + additionalProperties: false + properties: + maximum-speed: + description: A string property that specifies the maximum + supported speed of a USB3 port. + $ref: /schemas/types.yaml#/definitions/string + oneOf: + - description: The USB3 port supports USB 3.1 Gen 2 speed. + This is the default. + const: super-speed-plus + - description: The USB3 port supports USB 3.1 Gen 1 speed + only. + const: super-speed + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb3-3: + type: object + additionalProperties: false + properties: + maximum-speed: + description: A string property that specifies the maximum + supported speed of a USB3 port. + $ref: /schemas/types.yaml#/definitions/string + oneOf: + - description: The USB3 port supports USB 3.1 Gen 2 speed. + This is the default. + const: super-speed-plus + - description: The USB3 port supports USB 3.1 Gen 1 speed + only. + const: super-speed + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + +additionalProperties: false + +required: + - compatible + - reg + - resets + - reset-names + - avdd-usb-supply + - vclamp-usb-supply + +examples: + - | + #include <dt-bindings/clock/tegra194-clock.h> + #include <dt-bindings/gpio/tegra194-gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/reset/tegra194-reset.h> + + padctl@3520000 { + compatible = "nvidia,tegra194-xusb-padctl"; + reg = <0x03520000 0x1000>, + <0x03540000 0x1000>; + reg-names = "padctl", "ao"; + interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_HIGH>; + + resets = <&bpmp TEGRA194_RESET_XUSB_PADCTL>; + reset-names = "padctl"; + + avdd-usb-supply = <&vdd_usb_3v3>; + vclamp-usb-supply = <&vdd_1v8ao>; + + pads { + usb2 { + clocks = <&bpmp TEGRA194_CLK_USB2_TRK>; + clock-names = "trk"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-1 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + + usb2-2 { + nvidia,function = "xusb"; + status = "disabled"; + #phy-cells = <0>; + }; + + usb2-3 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + }; + }; + + usb3 { + lanes { + usb3-0 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + + usb3-1 { + nvidia,function = "xusb"; + status = "disabled"; + #phy-cells = <0>; + }; + + usb3-2 { + nvidia,function = "xusb"; + status = "disabled"; + #phy-cells = <0>; + }; + + usb3-3 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + status = "disabled"; + }; + + usb2-1 { + vbus-supply = <&vdd_5v0_sys>; + mode = "host"; + }; + + usb2-2 { + status = "disabled"; + }; + + usb2-3 { + vbus-supply = <&vdd_5v_sata>; + mode = "host"; + }; + + usb3-0 { + vbus-supply = <&vdd_5v0_sys>; + nvidia,usb2-companion = <1>; + }; + + usb3-1 { + status = "disabled"; + }; + + usb3-2 { + status = "disabled"; + }; + + usb3-3 { + maximum-speed = "super-speed"; + vbus-supply = <&vdd_5v0_sys>; + nvidia,usb2-companion = <3>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.yaml b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.yaml new file mode 100644 index 000000000..d61585c96 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra20-usb-phy.yaml @@ -0,0 +1,373 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/nvidia,tegra20-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra USB PHY + +maintainers: + - Dmitry Osipenko <digetx@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + - Thierry Reding <thierry.reding@gmail.com> + +properties: + compatible: + oneOf: + - items: + - enum: + - nvidia,tegra124-usb-phy + - nvidia,tegra114-usb-phy + - enum: + - nvidia,tegra30-usb-phy + - items: + - enum: + - nvidia,tegra30-usb-phy + - nvidia,tegra20-usb-phy + + reg: + minItems: 1 + maxItems: 2 + description: | + PHY0 and PHY2 share power and ground, PHY0 contains shared registers. + PHY0 and PHY2 must specify two register sets, where the first set is + PHY own registers and the second set is the PHY0 registers. + + clocks: + anyOf: + - items: + - description: Registers clock + - description: Main PHY clock + + - items: + - description: Registers clock + - description: Main PHY clock + - description: ULPI PHY clock + + - items: + - description: Registers clock + - description: Main PHY clock + - description: UTMI pads control registers clock + + - items: + - description: Registers clock + - description: Main PHY clock + - description: UTMI timeout clock + - description: UTMI pads control registers clock + + clock-names: + oneOf: + - items: + - const: reg + - const: pll_u + + - items: + - const: reg + - const: pll_u + - const: ulpi-link + + - items: + - const: reg + - const: pll_u + - const: utmi-pads + + - items: + - const: reg + - const: pll_u + - const: timer + - const: utmi-pads + + interrupts: + maxItems: 1 + + resets: + oneOf: + - maxItems: 1 + description: PHY reset + + - items: + - description: PHY reset + - description: UTMI pads reset + + reset-names: + oneOf: + - const: usb + + - items: + - const: usb + - const: utmi-pads + + "#phy-cells": + const: 0 + + phy_type: + $ref: /schemas/types.yaml#/definitions/string + enum: [utmi, ulpi, hsic] + + dr_mode: + $ref: /schemas/types.yaml#/definitions/string + enum: [host, peripheral, otg] + default: host + + vbus-supply: + description: Regulator controlling USB VBUS. + + nvidia,has-legacy-mode: + description: | + Indicates whether this controller can operate in legacy mode + (as APX 2500 / 2600). In legacy mode some registers are accessed + through the APB_MISC base address instead of the USB controller. + type: boolean + + nvidia,is-wired: + description: | + Indicates whether we can do certain kind of power optimizations for + the devices that are always connected. e.g. modem. + type: boolean + + nvidia,has-utmi-pad-registers: + description: | + Indicates whether this controller contains the UTMI pad control + registers common to all USB controllers. + type: boolean + + nvidia,hssync-start-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: | + Number of 480 MHz clock cycles to wait before start of sync launches + RxActive. + + nvidia,elastic-limit: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: Variable FIFO Depth of elastic input store. + + nvidia,idle-wait-delay: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 31 + description: | + Number of 480 MHz clock cycles of idle to wait before declare IDLE. + + nvidia,term-range-adj: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + description: Range adjustment on terminations. + + nvidia,xcvr-setup: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 127 + description: Input of XCVR cell, HS driver output control. + + nvidia,xcvr-setup-use-fuses: + description: Indicates that the value is read from the on-chip fuses. + type: boolean + + nvidia,xcvr-lsfslew: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + description: LS falling slew rate control. + + nvidia,xcvr-lsrslew: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + description: LS rising slew rate control. + + nvidia,xcvr-hsslew: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 511 + description: HS slew rate control. + + nvidia,hssquelch-level: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + description: HS squelch detector level. + + nvidia,hsdiscon-level: + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 7 + description: HS disconnect detector level. + + nvidia,phy-reset-gpio: + maxItems: 1 + description: GPIO used to reset the PHY. + + nvidia,pmc: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: Phandle to Power Management controller. + - description: USB controller ID. + description: + Phandle to Power Management controller. + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - "#phy-cells" + - phy_type + +additionalProperties: false + +allOf: + - if: + properties: + phy_type: + const: utmi + + then: + properties: + reg: + minItems: 2 + maxItems: 2 + + resets: + maxItems: 2 + + reset-names: + maxItems: 2 + + required: + - nvidia,hssync-start-delay + - nvidia,elastic-limit + - nvidia,idle-wait-delay + - nvidia,term-range-adj + - nvidia,xcvr-lsfslew + - nvidia,xcvr-lsrslew + + anyOf: + - required: ["nvidia,xcvr-setup"] + - required: ["nvidia,xcvr-setup-use-fuses"] + + if: + properties: + compatible: + contains: + const: nvidia,tegra30-usb-phy + + then: + properties: + clocks: + maxItems: 3 + + clock-names: + items: + - const: reg + - const: pll_u + - const: utmi-pads + + required: + - nvidia,xcvr-hsslew + - nvidia,hssquelch-level + - nvidia,hsdiscon-level + + else: + properties: + clocks: + maxItems: 4 + + clock-names: + items: + - const: reg + - const: pll_u + - const: timer + - const: utmi-pads + + - if: + properties: + phy_type: + const: ulpi + + then: + properties: + reg: + minItems: 1 + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 3 + + clock-names: + minItems: 2 + maxItems: 3 + + oneOf: + - items: + - const: reg + - const: pll_u + + - items: + - const: reg + - const: pll_u + - const: ulpi-link + + resets: + minItems: 1 + maxItems: 2 + + reset-names: + minItems: 1 + maxItems: 2 + +examples: + - | + #include <dt-bindings/clock/tegra124-car.h> + + usb-phy@7d008000 { + compatible = "nvidia,tegra124-usb-phy", "nvidia,tegra30-usb-phy"; + reg = <0x7d008000 0x4000>, + <0x7d000000 0x4000>; + interrupts = <0 97 4>; + phy_type = "utmi"; + clocks = <&tegra_car TEGRA124_CLK_USB3>, + <&tegra_car TEGRA124_CLK_PLL_U>, + <&tegra_car TEGRA124_CLK_USBD>; + clock-names = "reg", "pll_u", "utmi-pads"; + resets = <&tegra_car 59>, <&tegra_car 22>; + reset-names = "usb", "utmi-pads"; + #phy-cells = <0>; + nvidia,hssync-start-delay = <0>; + nvidia,idle-wait-delay = <17>; + nvidia,elastic-limit = <16>; + nvidia,term-range-adj = <6>; + nvidia,xcvr-setup = <9>; + nvidia,xcvr-lsfslew = <0>; + nvidia,xcvr-lsrslew = <3>; + nvidia,hssquelch-level = <2>; + nvidia,hsdiscon-level = <5>; + nvidia,xcvr-hsslew = <12>; + nvidia,pmc = <&tegra_pmc 2>; + }; + + - | + #include <dt-bindings/clock/tegra20-car.h> + + usb-phy@c5004000 { + compatible = "nvidia,tegra20-usb-phy"; + reg = <0xc5004000 0x4000>; + interrupts = <0 21 4>; + phy_type = "ulpi"; + clocks = <&tegra_car TEGRA20_CLK_USB2>, + <&tegra_car TEGRA20_CLK_PLL_U>, + <&tegra_car TEGRA20_CLK_CDEV2>; + clock-names = "reg", "pll_u", "ulpi-link"; + resets = <&tegra_car 58>, <&tegra_car 22>; + reset-names = "usb", "utmi-pads"; + #phy-cells = <0>; + nvidia,pmc = <&tegra_pmc 1>; + }; diff --git a/Documentation/devicetree/bindings/phy/nvidia,tegra210-xusb-padctl.yaml b/Documentation/devicetree/bindings/phy/nvidia,tegra210-xusb-padctl.yaml new file mode 100644 index 000000000..e9237c58c --- /dev/null +++ b/Documentation/devicetree/bindings/phy/nvidia,tegra210-xusb-padctl.yaml @@ -0,0 +1,786 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/nvidia,tegra210-xusb-padctl.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra210 XUSB pad controller + +maintainers: + - Thierry Reding <thierry.reding@gmail.com> + - Jon Hunter <jonathanh@nvidia.com> + +description: | + The Tegra XUSB pad controller manages a set of I/O lanes (with differential + signals) which connect directly to pins/pads on the SoC package. Each lane + is controlled by a HW block referred to as a "pad" in the Tegra hardware + documentation. Each such "pad" may control either one or multiple lanes, + and thus contains any logic common to all its lanes. Each lane can be + separately configured and powered up. + + Some of the lanes are high-speed lanes, which can be used for PCIe, SATA or + super-speed USB. Other lanes are for various types of low-speed, full-speed + or high-speed USB (such as UTMI, ULPI and HSIC). The XUSB pad controller + contains a software-configurable mux that sits between the I/O controller + ports (e.g. PCIe) and the lanes. + + In addition to per-lane configuration, USB 3.0 ports may require additional + settings on a per-board basis. + + Pads will be represented as children of the top-level XUSB pad controller + device tree node. Each lane exposed by the pad will be represented by its + own subnode and can be referenced by users of the lane using the standard + PHY bindings, as described by the phy-bindings.txt file in this directory. + + The Tegra hardware documentation refers to the connection between the XUSB + pad controller and the XUSB controller as "ports". This is confusing since + "port" is typically used to denote the physical USB receptacle. The device + tree binding in this document uses the term "port" to refer to the logical + abstraction of the signals that are routed to a USB receptacle (i.e. a PHY + for the USB signal, the VBUS power supply, the USB 2.0 companion port for + USB 3.0 receptacles, ...). + +properties: + compatible: + const: nvidia,tegra210-xusb-padctl + + reg: + maxItems: 1 + + resets: + items: + - description: pad controller reset + + interrupts: + items: + - description: XUSB pad controller interrupt + + reset-names: + items: + - const: padctl + + avdd-pll-utmip-supply: + description: UTMI PLL power supply. Must supply 1.8 V. + + avdd-pll-uerefe-supply: + description: PLLE reference PLL power supply. Must supply 1.05 V. + + dvdd-pex-pll-supply: + description: PCIe/USB3 PLL power supply. Must supply 1.05 V. + + hvdd-pex-pll-e-supply: + description: High-voltage PLLE power supply. Must supply 1.8 V. + + nvidia,pmc: + description: phandle to the Tegra Power Management Controller (PMC) node + $ref: /schemas/types.yaml#/definitions/phandle + + pads: + description: A required child node named "pads" contains a list of + subnodes, one for each of the pads exposed by the XUSB pad controller. + Each pad may need additional resources that can be referenced in its + pad node. + + The "status" property is used to enable or disable the use of a pad. + If set to "disabled", the pad will not be used on the given board. In + order to use the pad and any of its lanes, this property must be set + to "okay" or be absent. + type: object + additionalProperties: false + properties: + usb2: + type: object + additionalProperties: false + properties: + clocks: + items: + - description: USB2 tracking clock + + clock-names: + items: + - const: trk + + lanes: + type: object + additionalProperties: false + properties: + usb2-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb, uart ] + + usb2-1: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb, uart ] + + usb2-2: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb, uart ] + + usb2-3: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb, uart ] + + hsic: + type: object + additionalProperties: false + properties: + clocks: + items: + - description: HSIC tracking clock + + clock-names: + items: + - const: trk + + lanes: + type: object + additionalProperties: false + properties: + hsic-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb ] + + hsic-1: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ snps, xusb ] + + pcie: + type: object + additionalProperties: false + properties: + clocks: + items: + - description: PCIe PLL clock source + + clock-names: + items: + - const: pll + + resets: + items: + - description: PCIe PHY reset + + reset-names: + items: + - const: phy + + lanes: + type: object + additionalProperties: false + properties: + pcie-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie-x1, usb3-ss, pcie-x4 ] + + pcie-1: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie-x1, usb3-ss, pcie-x4 ] + + pcie-2: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie-x1, usb3-ss, pcie-x4 ] + + pcie-3: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie-x1, usb3-ss, pcie-x4 ] + + pcie-4: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie-x1, usb3-ss, pcie-x4 ] + + pcie-5: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie-x1, usb3-ss, pcie-x4 ] + + pcie-6: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ pcie-x1, usb3-ss, pcie-x4 ] + + sata: + type: object + additionalProperties: false + properties: + clocks: + items: + - description: SATA PLL clock source + + clock-names: + items: + - const: pll + + resets: + items: + - description: SATA PHY reset + + reset-names: + items: + - const: phy + + lanes: + type: object + additionalProperties: false + properties: + sata-0: + type: object + additionalProperties: false + properties: + "#phy-cells": + const: 0 + + nvidia,function: + description: Function selection for this lane. + $ref: /schemas/types.yaml#/definitions/string + enum: [ usb3-ss, sata ] + + ports: + description: A required child node named "ports" contains a list of + subnodes, one for each of the ports exposed by the XUSB pad controller. + Each port may need additional resources that can be referenced in its + port node. + + The "status" property is used to enable or disable the use of a port. + If set to "disabled", the port will not be used on the given board. In + order to use the port, this property must be set to "okay". + type: object + additionalProperties: false + properties: + usb2-0: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + dependencies: + usb-role-switch: [ connector ] + + usb2-1: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + dependencies: + usb-role-switch: [ connector ] + + usb2-2: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + dependencies: + usb-role-switch: [ connector ] + + usb2-3: + type: object + additionalProperties: false + properties: + # no need to further describe this because the connector will + # match on gpio-usb-b-connector or usb-b-connector and cause + # that binding to be selected for the subnode + connector: + type: object + + mode: + description: A string that determines the mode in which to + run the port. + $ref: /schemas/types.yaml#/definitions/string + enum: [ host, peripheral, otg ] + + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + usb-role-switch: + description: | + A boolean property whole presence indicates that the port + supports OTG or peripheral mode. If present, the port + supports switching between USB host and peripheral roles. + A connector must be added as a subnode in that case. + + See ../connector/usb-connector.yaml. + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + dependencies: + usb-role-switch: [ connector ] + + hsic-0: + type: object + additionalProperties: false + properties: + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + hsic-1: + type: object + additionalProperties: false + properties: + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb3-0: + type: object + additionalProperties: false + properties: + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb3-1: + type: object + additionalProperties: false + properties: + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb3-2: + type: object + additionalProperties: false + properties: + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + + usb3-3: + type: object + additionalProperties: false + properties: + nvidia,internal: + description: A boolean property whose presence determines + that a port is internal. In the absence of this property + the port is considered to be external. + $ref: /schemas/types.yaml#/definitions/flag + + nvidia,usb2-companion: + description: A single cell that specifies the physical port + number to map this super-speed USB port to. The range of + valid port numbers varies with the SoC generation. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 1, 2, 3 ] + + vbus-supply: + description: A phandle to the regulator supplying the VBUS + voltage. + +additionalProperties: false + +required: + - avdd-pll-utmip-supply + - avdd-pll-uerefe-supply + - dvdd-pex-pll-supply + - hvdd-pex-pll-e-supply + +examples: + - | + #include <dt-bindings/clock/tegra210-car.h> + #include <dt-bindings/gpio/tegra-gpio.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + + padctl@7009f000 { + compatible = "nvidia,tegra210-xusb-padctl"; + reg = <0x7009f000 0x1000>; + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; + resets = <&tegra_car 142>; + reset-names = "padctl"; + + avdd-pll-utmip-supply = <&vdd_1v8>; + avdd-pll-uerefe-supply = <&vdd_pex_1v05>; + dvdd-pex-pll-supply = <&vdd_pex_1v05>; + hvdd-pex-pll-e-supply = <&vdd_1v8>; + + pads { + usb2 { + clocks = <&tegra_car TEGRA210_CLK_USB2_TRK>; + clock-names = "trk"; + + lanes { + usb2-0 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + + usb2-1 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + + usb2-2 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + + usb2-3 { + nvidia,function = "xusb"; + #phy-cells = <0>; + }; + }; + }; + + hsic { + clocks = <&tegra_car TEGRA210_CLK_HSIC_TRK>; + clock-names = "trk"; + status = "disabled"; + + lanes { + hsic-0 { + status = "disabled"; + #phy-cells = <0>; + }; + + hsic-1 { + status = "disabled"; + #phy-cells = <0>; + }; + }; + }; + + pcie { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 205>; + reset-names = "phy"; + + lanes { + pcie-0 { + nvidia,function = "pcie-x1"; + #phy-cells = <0>; + }; + + pcie-1 { + nvidia,function = "pcie-x4"; + #phy-cells = <0>; + }; + + pcie-2 { + nvidia,function = "pcie-x4"; + #phy-cells = <0>; + }; + + pcie-3 { + nvidia,function = "pcie-x4"; + #phy-cells = <0>; + }; + + pcie-4 { + nvidia,function = "pcie-x4"; + #phy-cells = <0>; + }; + + pcie-5 { + nvidia,function = "usb3-ss"; + #phy-cells = <0>; + }; + + pcie-6 { + nvidia,function = "usb3-ss"; + #phy-cells = <0>; + }; + }; + }; + + sata { + clocks = <&tegra_car TEGRA210_CLK_PLL_E>; + clock-names = "pll"; + resets = <&tegra_car 204>; + reset-names = "phy"; + + lanes { + sata-0 { + nvidia,function = "sata"; + #phy-cells = <0>; + }; + }; + }; + }; + + ports { + usb2-0 { + mode = "peripheral"; + usb-role-switch; + + connector { + compatible = "gpio-usb-b-connector", + "usb-b-connector"; + label = "micro-USB"; + type = "micro"; + vbus-gpios = <&gpio TEGRA_GPIO(CC, 4) GPIO_ACTIVE_LOW>; + }; + }; + + usb2-1 { + vbus-supply = <&vdd_5v0_rtl>; + mode = "host"; + }; + + usb2-2 { + vbus-supply = <&vdd_usb_vbus>; + mode = "host"; + }; + + usb2-3 { + mode = "host"; + }; + + hsic-0 { + status = "disabled"; + }; + + hsic-1 { + status = "disabled"; + }; + + usb3-0 { + nvidia,usb2-companion = <1>; + }; + + usb3-1 { + nvidia,usb2-companion = <2>; + }; + + usb3-2 { + status = "disabled"; + }; + + usb3-3 { + status = "disabled"; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-armada38x-comphy.txt b/Documentation/devicetree/bindings/phy/phy-armada38x-comphy.txt new file mode 100644 index 000000000..8b5a7a28a --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-armada38x-comphy.txt @@ -0,0 +1,48 @@ +mvebu armada 38x comphy driver +------------------------------ + +This comphy controller can be found on Marvell Armada 38x. It provides a +number of shared PHYs used by various interfaces (network, sata, usb, +PCIe...). + +Required properties: + +- compatible: should be "marvell,armada-380-comphy" +- reg: should contain the comphy register location and length. +- #address-cells: should be 1. +- #size-cells: should be 0. + +Optional properties: + +- reg-names: must be "comphy" as the first name, and "conf". +- reg: must contain the comphy register location and length as the first + pair, followed by an optional configuration register address and + length pair. + +A sub-node is required for each comphy lane provided by the comphy. + +Required properties (child nodes): + +- reg: comphy lane number. +- #phy-cells : from the generic phy bindings, must be 1. Defines the + input port to use for a given comphy lane. + +Example: + + comphy: phy@18300 { + compatible = "marvell,armada-380-comphy"; + reg-names = "comphy", "conf"; + reg = <0x18300 0x100>, <0x18460 4>; + #address-cells = <1>; + #size-cells = <0>; + + cpm_comphy0: phy@0 { + reg = <0>; + #phy-cells = <1>; + }; + + cpm_comphy1: phy@1 { + reg = <1>; + #phy-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-ath79-usb.txt b/Documentation/devicetree/bindings/phy/phy-ath79-usb.txt new file mode 100644 index 000000000..c3a29c5fe --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-ath79-usb.txt @@ -0,0 +1,18 @@ +* Atheros AR71XX/9XXX USB PHY + +Required properties: +- compatible: "qca,ar7100-usb-phy" +- #phys-cells: should be 0 +- reset-names: "phy"[, "suspend-override"] +- resets: references to the reset controllers + +Example: + + usb-phy { + compatible = "qca,ar7100-usb-phy"; + + reset-names = "phy", "suspend-override"; + resets = <&rst 4>, <&rst 3>; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-bindings.txt b/Documentation/devicetree/bindings/phy/phy-bindings.txt new file mode 100644 index 000000000..c4eb38902 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-bindings.txt @@ -0,0 +1,72 @@ +This document explains only the device tree data binding. For general +information about PHY subsystem refer to Documentation/driver-api/phy/phy.rst + +PHY device node +=============== + +Required Properties: +#phy-cells: Number of cells in a PHY specifier; The meaning of all those + cells is defined by the binding for the phy node. The PHY + provider can use the values in cells to find the appropriate + PHY. + +Optional Properties: +phy-supply: Phandle to a regulator that provides power to the PHY. This + regulator will be managed during the PHY power on/off sequence. + +For example: + +phys: phy { + compatible = "xxx"; + reg = <...>; + . + . + #phy-cells = <1>; + . + . +}; + +That node describes an IP block (PHY provider) that implements 2 different PHYs. +In order to differentiate between these 2 PHYs, an additional specifier should be +given while trying to get a reference to it. + +PHY user node +============= + +Required Properties: +phys : the phandle for the PHY device (used by the PHY subsystem; not to be + confused with the Ethernet specific 'phy' and 'phy-handle' properties, + see Documentation/devicetree/bindings/net/ethernet.txt for these) +phy-names : the names of the PHY corresponding to the PHYs present in the + *phys* phandle + +Example 1: +usb1: usb_otg_ss@xxx { + compatible = "xxx"; + reg = <xxx>; + . + . + phys = <&usb2_phy>, <&usb3_phy>; + phy-names = "usb2phy", "usb3phy"; + . + . +}; + +This node represents a controller that uses two PHYs, one for usb2 and one for +usb3. + +Example 2: +usb2: usb_otg_ss@xxx { + compatible = "xxx"; + reg = <xxx>; + . + . + phys = <&phys 1>; + phy-names = "usbphy"; + . + . +}; + +This node represents a controller that uses one of the PHYs of the PHY provider +device defined previously. Note that the phy handle has an additional specifier +"1" to differentiate between the two PHYs. diff --git a/Documentation/devicetree/bindings/phy/phy-cadence-sierra.yaml b/Documentation/devicetree/bindings/phy/phy-cadence-sierra.yaml new file mode 100644 index 000000000..37f028f7a --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-cadence-sierra.yaml @@ -0,0 +1,166 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/phy-cadence-sierra.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cadence Sierra PHY + +description: + This binding describes the Cadence Sierra PHY. Sierra PHY supports multilink + multiprotocol combinations including protocols such as PCIe, USB etc. + +maintainers: + - Swapnil Jakhade <sjakhade@cadence.com> + - Yuti Amonkar <yamonkar@cadence.com> + +properties: + compatible: + enum: + - cdns,sierra-phy-t0 + - ti,sierra-phy-t0 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + '#clock-cells': + const: 1 + + resets: + minItems: 1 + items: + - description: Sierra PHY reset. + - description: Sierra APB reset. This is optional. + + reset-names: + minItems: 1 + items: + - const: sierra_reset + - const: sierra_apb + + reg: + maxItems: 1 + description: + Offset of the Sierra PHY configuration registers. + + reg-names: + const: serdes + + clocks: + minItems: 2 + maxItems: 4 + + clock-names: + minItems: 2 + items: + - const: cmn_refclk_dig_div + - const: cmn_refclk1_dig_div + - const: pll0_refclk + - const: pll1_refclk + + cdns,autoconf: + type: boolean + description: + A boolean property whose presence indicates that the PHY registers will be + configured by hardware. If not present, all sub-node optional properties + must be provided. + +patternProperties: + '^phy@[0-9a-f]$': + type: object + description: + Each group of PHY lanes with a single master lane should be represented as + a sub-node. Note that the actual configuration of each lane is determined + by hardware strapping, and must match the configuration specified here. + properties: + reg: + description: + The master lane number. This is the lowest numbered lane in the lane group. + minimum: 0 + maximum: 15 + + resets: + minItems: 1 + maxItems: 4 + description: + Contains list of resets, one per lane, to get all the link lanes out of reset. + + "#phy-cells": + const: 0 + + cdns,phy-type: + description: + Specifies the type of PHY for which the group of PHY lanes is used. + Refer include/dt-bindings/phy/phy.h. Constants from the header should be used. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [2, 4] + + cdns,num-lanes: + description: + Number of lanes in this group. The group is made up of consecutive lanes. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 16 + + cdns,ssc-mode: + description: + Specifies the Spread Spectrum Clocking mode used. It can be NO_SSC, + EXTERNAL_SSC or INTERNAL_SSC. + Refer include/dt-bindings/phy/phy-cadence.h for the constants to be used. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + default: 1 + + required: + - reg + - resets + - "#phy-cells" + + additionalProperties: false + +required: + - compatible + - "#address-cells" + - "#size-cells" + - reg + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/phy/phy.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + + sierra-phy@fd240000 { + compatible = "cdns,sierra-phy-t0"; + reg = <0x0 0xfd240000 0x0 0x40000>; + resets = <&phyrst 0>, <&phyrst 1>; + reset-names = "sierra_reset", "sierra_apb"; + clocks = <&cmn_refclk_dig_div>, <&cmn_refclk1_dig_div>; + clock-names = "cmn_refclk_dig_div", "cmn_refclk1_dig_div"; + #address-cells = <1>; + #size-cells = <0>; + pcie0_phy0: phy@0 { + reg = <0>; + resets = <&phyrst 2>; + cdns,num-lanes = <2>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_PCIE>; + }; + pcie0_phy1: phy@2 { + reg = <2>; + resets = <&phyrst 4>; + cdns,num-lanes = <1>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_PCIE>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml b/Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml new file mode 100644 index 000000000..dfb31314f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml @@ -0,0 +1,212 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/phy-cadence-torrent.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Cadence Torrent SD0801 PHY + +description: + This binding describes the Cadence SD0801 PHY (also known as Torrent PHY) + hardware included with the Cadence MHDP DisplayPort controller. Torrent + PHY also supports multilink multiprotocol combinations including protocols + such as PCIe, USB, SGMII, QSGMII etc. + +maintainers: + - Swapnil Jakhade <sjakhade@cadence.com> + - Yuti Amonkar <yamonkar@cadence.com> + +properties: + compatible: + enum: + - cdns,torrent-phy + - ti,j721e-serdes-10g + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + '#clock-cells': + const: 1 + + clocks: + minItems: 1 + maxItems: 2 + description: + PHY reference clock for 1 item. Must contain an entry in clock-names. + Optional Parent to enable output reference clock. + + clock-names: + minItems: 1 + items: + - const: refclk + - const: phy_en_refclk + + reg: + minItems: 1 + items: + - description: Offset of the Torrent PHY configuration registers. + - description: Offset of the DPTX PHY configuration registers. + + reg-names: + minItems: 1 + items: + - const: torrent_phy + - const: dptx_phy + + resets: + minItems: 1 + items: + - description: Torrent PHY reset. + - description: Torrent APB reset. This is optional. + + reset-names: + minItems: 1 + items: + - const: torrent_reset + - const: torrent_apb + +patternProperties: + '^phy@[0-3]$': + type: object + description: + Each group of PHY lanes with a single master lane should be represented as a sub-node. + properties: + reg: + description: + The master lane number. This is the lowest numbered lane in the lane group. + minimum: 0 + maximum: 3 + + resets: + minItems: 1 + maxItems: 4 + description: + Contains list of resets, one per lane, to get all the link lanes out of reset. + + "#phy-cells": + const: 0 + + cdns,phy-type: + description: + Specifies the type of PHY for which the group of PHY lanes is used. + Refer include/dt-bindings/phy/phy.h. Constants from the header should be used. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 1 + maximum: 9 + + cdns,num-lanes: + description: + Number of lanes. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [1, 2, 3, 4] + default: 4 + + cdns,ssc-mode: + description: + Specifies the Spread Spectrum Clocking mode used. It can be NO_SSC, + EXTERNAL_SSC or INTERNAL_SSC. + Refer include/dt-bindings/phy/phy-cadence.h for the constants to be used. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2] + default: 0 + + cdns,max-bit-rate: + description: + Maximum DisplayPort link bit rate to use, in Mbps + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [2160, 2430, 2700, 3240, 4320, 5400, 8100] + default: 8100 + + required: + - reg + - resets + - "#phy-cells" + - cdns,phy-type + - cdns,num-lanes + + additionalProperties: false + +required: + - compatible + - "#address-cells" + - "#size-cells" + - clocks + - clock-names + - reg + - reg-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/phy/phy.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + + torrent-phy@f0fb500000 { + compatible = "cdns,torrent-phy"; + reg = <0xf0 0xfb500000 0x0 0x00100000>, + <0xf0 0xfb030a00 0x0 0x00000040>; + reg-names = "torrent_phy", "dptx_phy"; + resets = <&phyrst 0>; + reset-names = "torrent_reset"; + clocks = <&ref_clk>; + clock-names = "refclk"; + #address-cells = <1>; + #size-cells = <0>; + phy@0 { + reg = <0>; + resets = <&phyrst 1>, <&phyrst 2>, + <&phyrst 3>, <&phyrst 4>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_DP>; + cdns,num-lanes = <4>; + cdns,max-bit-rate = <8100>; + }; + }; + }; + - | + #include <dt-bindings/phy/phy.h> + #include <dt-bindings/phy/phy-cadence.h> + + bus { + #address-cells = <2>; + #size-cells = <2>; + + torrent-phy@f0fb500000 { + compatible = "cdns,torrent-phy"; + reg = <0xf0 0xfb500000 0x0 0x00100000>; + reg-names = "torrent_phy"; + resets = <&phyrst 0>, <&phyrst 1>; + reset-names = "torrent_reset", "torrent_apb"; + clocks = <&ref_clk>; + clock-names = "refclk"; + #address-cells = <1>; + #size-cells = <0>; + phy@0 { + reg = <0>; + resets = <&phyrst 2>, <&phyrst 3>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_PCIE>; + cdns,num-lanes = <2>; + cdns,ssc-mode = <CDNS_SERDES_NO_SSC>; + }; + + phy@2 { + reg = <2>; + resets = <&phyrst 4>; + #phy-cells = <0>; + cdns,phy-type = <PHY_TYPE_SGMII>; + cdns,num-lanes = <1>; + cdns,ssc-mode = <CDNS_SERDES_NO_SSC>; + }; + }; + }; +... diff --git a/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt b/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt new file mode 100644 index 000000000..2eb9b2b69 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-cpcap-usb.txt @@ -0,0 +1,40 @@ +Motorola CPCAP PMIC USB PHY binding + +Required properties: +compatible: Shall be either "motorola,cpcap-usb-phy" or + "motorola,mapphone-cpcap-usb-phy" +#phy-cells: Shall be 0 +interrupts: CPCAP PMIC interrupts used by the USB PHY +interrupt-names: Interrupt names +io-channels: IIO ADC channels used by the USB PHY +io-channel-names: IIO ADC channel names +vusb-supply: Regulator for the PHY + +Optional properties: +pinctrl: Optional alternate pin modes for the PHY +pinctrl-names: Names for optional pin modes +mode-gpios: Optional GPIOs for configuring alternate modes + +Example: +cpcap_usb2_phy: phy { + compatible = "motorola,mapphone-cpcap-usb-phy"; + pinctrl-0 = <&usb_gpio_mux_sel1 &usb_gpio_mux_sel2>; + pinctrl-1 = <&usb_ulpi_pins>; + pinctrl-2 = <&usb_utmi_pins>; + pinctrl-3 = <&uart3_pins>; + pinctrl-names = "default", "ulpi", "utmi", "uart"; + #phy-cells = <0>; + interrupts-extended = < + &cpcap 15 0 &cpcap 14 0 &cpcap 28 0 &cpcap 19 0 + &cpcap 18 0 &cpcap 17 0 &cpcap 16 0 &cpcap 49 0 + &cpcap 48 1 + >; + interrupt-names = + "id_ground", "id_float", "se0conn", "vbusvld", + "sessvld", "sessend", "se1", "dm", "dp"; + mode-gpios = <&gpio2 28 GPIO_ACTIVE_HIGH + &gpio1 0 GPIO_ACTIVE_HIGH>; + io-channels = <&cpcap_adc 2>, <&cpcap_adc 7>; + io-channel-names = "vbus", "id"; + vusb-supply = <&vusb>; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt new file mode 100644 index 000000000..c26478be3 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-da8xx-usb.txt @@ -0,0 +1,40 @@ +TI DA8xx/OMAP-L1xx/AM18xx USB PHY + +Required properties: + - compatible: must be "ti,da830-usb-phy". + - #phy-cells: must be 1. + +This device controls the PHY for both the USB 1.1 OHCI and USB 2.0 OTG +controllers on DA8xx SoCs. Consumers of this device should use index 0 for +the USB 2.0 phy device and index 1 for the USB 1.1 phy device. + +It also requires a "syscon" node with compatible = "ti,da830-cfgchip", "syscon" +to access the CFGCHIP2 register. + +Example: + + cfgchip: cfgchip@1417c { + compatible = "ti,da830-cfgchip", "syscon"; + reg = <0x1417c 0x14>; + }; + + usb_phy: usb-phy { + compatible = "ti,da830-usb-phy"; + #phy-cells = <1>; + }; + + usb20: usb@200000 { + compatible = "ti,da830-musb"; + reg = <0x200000 0x1000>; + interrupts = <58>; + phys = <&usb_phy 0>; + phy-names = "usb-phy"; + }; + + usb11: usb@225000 { + compatible = "ti,da830-ohci"; + reg = <0x225000 0x1000>; + interrupts = <59>; + phys = <&usb_phy 1>; + phy-names = "usb-phy"; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-hi3798cv200-combphy.txt b/Documentation/devicetree/bindings/phy/phy-hi3798cv200-combphy.txt new file mode 100644 index 000000000..17b0c7613 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-hi3798cv200-combphy.txt @@ -0,0 +1,59 @@ +HiSilicon STB PCIE/SATA/USB3 PHY + +Required properties: +- compatible: Should be "hisilicon,hi3798cv200-combphy" +- reg: Should be the address space for COMBPHY configuration and state + registers in peripheral controller, e.g. PERI_COMBPHY0_CFG and + PERI_COMBPHY0_STATE for COMBPHY0 Hi3798CV200 SoC. +- #phy-cells: Should be 1. The cell number is used to select the phy mode + as defined in <dt-bindings/phy/phy.h>. +- clocks: The phandle to clock provider and clock specifier pair. +- resets: The phandle to reset controller and reset specifier pair. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties. + +Optional properties: +- hisilicon,fixed-mode: If the phy device doesn't support mode select + but a fixed mode setting, the property should be present to specify + the particular mode. +- hisilicon,mode-select-bits: If the phy device support mode select, + this property should be present to specify the register bits in + peripheral controller, as a 3 integers tuple: + <register_offset bit_shift bit_mask>. + +Notes: +- Between hisilicon,fixed-mode and hisilicon,mode-select-bits, one and only + one of them should be present. +- The device node should be a child of peripheral controller that contains + COMBPHY configuration/state and PERI_CTRL register used to select PHY mode. + Refer to arm/hisilicon/hisilicon.txt for the parent peripheral controller + bindings. + +Examples: + +perictrl: peripheral-controller@8a20000 { + compatible = "hisilicon,hi3798cv200-perictrl", "syscon", + "simple-mfd"; + reg = <0x8a20000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x8a20000 0x1000>; + + combphy0: phy@850 { + compatible = "hisilicon,hi3798cv200-combphy"; + reg = <0x850 0x8>; + #phy-cells = <1>; + clocks = <&crg HISTB_COMBPHY0_CLK>; + resets = <&crg 0x188 4>; + hisilicon,fixed-mode = <PHY_TYPE_USB3>; + }; + + combphy1: phy@858 { + compatible = "hisilicon,hi3798cv200-combphy"; + reg = <0x858 0x8>; + #phy-cells = <1>; + clocks = <&crg HISTB_COMBPHY1_CLK>; + resets = <&crg 0x188 12>; + hisilicon,mode-select-bits = <0x0008 11 (0x3 << 11)>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt b/Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt new file mode 100644 index 000000000..f17a56e21 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-hi6220-usb.txt @@ -0,0 +1,16 @@ +Hisilicon hi6220 usb PHY +----------------------- + +Required properties: +- compatible: should be "hisilicon,hi6220-usb-phy" +- #phy-cells: must be 0 +- hisilicon,peripheral-syscon: phandle of syscon used to control phy. +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + usb_phy: usbphy { + compatible = "hisilicon,hi6220-usb-phy"; + #phy-cells = <0>; + phy-supply = <&fixed_5v_hub>; + hisilicon,peripheral-syscon = <&sys_ctrl>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt b/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt new file mode 100644 index 000000000..104953e84 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-hisi-inno-usb2.txt @@ -0,0 +1,71 @@ +Device tree bindings for HiSilicon INNO USB2 PHY + +Required properties: +- compatible: Should be one of the following strings: + "hisilicon,inno-usb2-phy", + "hisilicon,hi3798cv200-usb2-phy". +- reg: Should be the address space for PHY configuration register in peripheral + controller, e.g. PERI_USB0 for USB 2.0 PHY01 on Hi3798CV200 SoC. +- clocks: The phandle and clock specifier pair for INNO USB2 PHY device + reference clock. +- resets: The phandle and reset specifier pair for INNO USB2 PHY device reset + signal. +- #address-cells: Must be 1. +- #size-cells: Must be 0. + +The INNO USB2 PHY device should be a child node of peripheral controller that +contains the PHY configuration register, and each device supports up to 2 PHY +ports which are represented as child nodes of INNO USB2 PHY device. + +Required properties for PHY port node: +- reg: The PHY port instance number. +- #phy-cells: Defined by generic PHY bindings. Must be 0. +- resets: The phandle and reset specifier pair for PHY port reset signal. + +Refer to phy/phy-bindings.txt for the generic PHY binding properties + +Example: + +perictrl: peripheral-controller@8a20000 { + compatible = "hisilicon,hi3798cv200-perictrl", "simple-mfd"; + reg = <0x8a20000 0x1000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x8a20000 0x1000>; + + usb2_phy1: usb2-phy@120 { + compatible = "hisilicon,hi3798cv200-usb2-phy"; + reg = <0x120 0x4>; + clocks = <&crg HISTB_USB2_PHY1_REF_CLK>; + resets = <&crg 0xbc 4>; + #address-cells = <1>; + #size-cells = <0>; + + usb2_phy1_port0: phy@0 { + reg = <0>; + #phy-cells = <0>; + resets = <&crg 0xbc 8>; + }; + + usb2_phy1_port1: phy@1 { + reg = <1>; + #phy-cells = <0>; + resets = <&crg 0xbc 9>; + }; + }; + + usb2_phy2: usb2-phy@124 { + compatible = "hisilicon,hi3798cv200-usb2-phy"; + reg = <0x124 0x4>; + clocks = <&crg HISTB_USB2_PHY2_REF_CLK>; + resets = <&crg 0xbc 6>; + #address-cells = <1>; + #size-cells = <0>; + + usb2_phy2_port0: phy@0 { + reg = <0>; + #phy-cells = <0>; + resets = <&crg 0xbc 10>; + }; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt new file mode 100644 index 000000000..643948b6b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt @@ -0,0 +1,40 @@ +Lantiq XWAY SoC RCU USB 1.1/2.0 PHY binding +=========================================== + +This binding describes the USB PHY hardware provided by the RCU module on the +Lantiq XWAY SoCs. + +This node has to be a sub node of the Lantiq RCU block. + +------------------------------------------------------------------------------- +Required properties (controller (parent) node): +- compatible : Should be one of + "lantiq,ase-usb2-phy" + "lantiq,danube-usb2-phy" + "lantiq,xrx100-usb2-phy" + "lantiq,xrx200-usb2-phy" + "lantiq,xrx300-usb2-phy" +- reg : Defines the following sets of registers in the parent + syscon device + - Offset of the USB PHY configuration register + - Offset of the USB Analog configuration + register (only for xrx200 and xrx200) +- clocks : References to the (PMU) "phy" clk gate. +- clock-names : Must be "phy" +- resets : References to the RCU USB configuration reset bits. +- reset-names : Must be one of the following: + "phy" (optional) + "ctrl" (shared) + +------------------------------------------------------------------------------- +Example for the USB PHYs on an xRX200 SoC: + usb_phy0: usb2-phy@18 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x18 4>, <0x38 4>; + + clocks = <&pmu PMU_GATE_USB0_PHY>; + clock-names = "phy"; + resets = <&reset1 4 4>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt new file mode 100644 index 000000000..3bb821cd6 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-lpc18xx-usb-otg.txt @@ -0,0 +1,26 @@ +NXP LPC18xx/43xx internal USB OTG PHY binding +--------------------------------------------- + +This file contains documentation for the internal USB OTG PHY found +in NXP LPC18xx and LPC43xx SoCs. + +Required properties: +- compatible : must be "nxp,lpc1850-usb-otg-phy" +- clocks : must be exactly one entry +See: Documentation/devicetree/bindings/clock/clock-bindings.txt +- #phy-cells : must be 0 for this phy +See: Documentation/devicetree/bindings/phy/phy-bindings.txt + +The phy node must be a child of the creg syscon node. + +Example: +creg: syscon@40043000 { + compatible = "nxp,lpc1850-creg", "syscon", "simple-mfd"; + reg = <0x40043000 0x1000>; + + usb0_otg_phy: phy { + compatible = "nxp,lpc1850-usb-otg-phy"; + clocks = <&ccu1 CLK_USB0>; + #phy-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-mapphone-mdm6600.txt b/Documentation/devicetree/bindings/phy/phy-mapphone-mdm6600.txt new file mode 100644 index 000000000..29427d4f0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mapphone-mdm6600.txt @@ -0,0 +1,29 @@ +Device tree binding documentation for Motorola Mapphone MDM6600 USB PHY + +Required properties: +- compatible Must be "motorola,mapphone-mdm6600" +- enable-gpios GPIO to enable the USB PHY +- power-gpios GPIO to power on the device +- reset-gpios GPIO to reset the device +- motorola,mode-gpios Two GPIOs to configure MDM6600 USB start-up mode for + normal mode versus USB flashing mode +- motorola,cmd-gpios Three GPIOs to control the power state of the MDM6600 +- motorola,status-gpios Three GPIOs to read the power state of the MDM6600 + +Example: + +usb-phy { + compatible = "motorola,mapphone-mdm6600"; + enable-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>; + power-gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; + reset-gpios = <&gpio2 17 GPIO_ACTIVE_HIGH>; + motorola,mode-gpios = <&gpio5 20 GPIO_ACTIVE_HIGH>, + <&gpio5 21 GPIO_ACTIVE_HIGH>; + motorola,cmd-gpios = <&gpio4 7 GPIO_ACTIVE_HIGH>, + <&gpio4 8 GPIO_ACTIVE_HIGH>, + <&gpio5 14 GPIO_ACTIVE_HIGH>; + motorola,status-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>, + <&gpio2 21 GPIO_ACTIVE_HIGH>, + <&gpio2 23 GPIO_ACTIVE_HIGH>; + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt new file mode 100644 index 000000000..89caa885d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-miphy28lp.txt @@ -0,0 +1,117 @@ +STMicroelectronics STi MIPHY28LP PHY binding +============================================ + +This binding describes a miphy device that is used to control PHY hardware +for SATA, PCIe or USB3. + +Required properties (controller (parent) node): +- compatible : Should be "st,miphy28lp-phy". +- st,syscfg : Should be a phandle of the system configuration register group + which contain the SATA, PCIe or USB3 mode setting bits. + +Required nodes : A sub-node is required for each channel the controller + provides. Address range information including the usual + 'reg' and 'reg-names' properties are used inside these + nodes to describe the controller's topology. These nodes + are translated by the driver's .xlate() function. + +Required properties (port (child) node): +- #phy-cells : Should be 1 (See second example) + Cell after port phandle is device type from: + - PHY_TYPE_SATA + - PHY_TYPE_PCI + - PHY_TYPE_USB3 +- reg : Address and length of the register set for the device. +- reg-names : The names of the register addresses corresponding to the registers + filled in "reg". It can also contain the offset of the system configuration + registers used as glue-logic to setup the device for SATA/PCIe or USB3 + devices. +- st,syscfg : Offset of the parent configuration register. +- resets : phandle to the parent reset controller. +- reset-names : Associated name must be "miphy-sw-rst". + +Optional properties (port (child) node): +- st,osc-rdy : to check the MIPHY0_OSC_RDY status in the glue-logic. This + is not available in all the MiPHY. For example, for STiH407, only the + MiPHY0 has this bit. +- st,osc-force-ext : to select the external oscillator. This can change from + different MiPHY inside the same SoC. +- st,sata_gen : to select which SATA_SPDMODE has to be set in the SATA system config + register. +- st,px_rx_pol_inv : to invert polarity of RXn/RXp (respectively negative line and positive + line). +- st,scc-on : enable ssc to reduce effects of EMI (only for sata or PCIe). +- st,tx-impedance-comp : to compensate tx impedance avoiding out of range values. + +example: + + miphy28lp_phy: miphy28lp@9b22000 { + compatible = "st,miphy28lp-phy"; + st,syscfg = <&syscfg_core>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + phy_port0: port@9b22000 { + reg = <0x9b22000 0xff>, + <0x9b09000 0xff>, + <0x9b04000 0xff>; + reg-names = "sata-up", + "pcie-up", + "pipew"; + + st,syscfg = <0x114 0x818 0xe0 0xec>; + #phy-cells = <1>; + st,osc-rdy; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY0_SOFTRESET>; + }; + + phy_port1: port@9b2a000 { + reg = <0x9b2a000 0xff>, + <0x9b19000 0xff>, + <0x9b14000 0xff>; + reg-names = "sata-up", + "pcie-up", + "pipew"; + + st,syscfg = <0x118 0x81c 0xe4 0xf0>; + + #phy-cells = <1>; + st,osc-force-ext; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY1_SOFTRESET>; + }; + + phy_port2: port@8f95000 { + reg = <0x8f95000 0xff>, + <0x8f90000 0xff>; + reg-names = "pipew", + "usb3-up"; + + st,syscfg = <0x11c 0x820>; + + #phy-cells = <1>; + reset-names = "miphy-sw-rst"; + resets = <&softreset STIH407_MIPHY2_SOFTRESET>; + }; + }; + + +Specifying phy control of devices +================================= + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the miphy device node and an index +specifying which configuration to use, as described in phy-bindings.txt. + +example: + sata0: sata@9b20000 { + ... + phys = <&phy_port0 PHY_TYPE_SATA>; + ... + }; + +Macro definitions for the supported miphy configuration can be found in: + +include/dt-bindings/phy/phy.h diff --git a/Documentation/devicetree/bindings/phy/phy-miphy365x.txt b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt new file mode 100644 index 000000000..8772900e0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-miphy365x.txt @@ -0,0 +1,77 @@ +STMicroelectronics STi MIPHY365x PHY binding +============================================ + +This binding describes a miphy device that is used to control PHY hardware +for SATA and PCIe. + +Required properties (controller (parent) node): +- compatible : Should be "st,miphy365x-phy" +- st,syscfg : Phandle / integer array property. Phandle of sysconfig group + containing the miphy registers and integer array should contain + an entry for each port sub-node, specifying the control + register offset inside the sysconfig group. + +Required nodes : A sub-node is required for each channel the controller + provides. Address range information including the usual + 'reg' and 'reg-names' properties are used inside these + nodes to describe the controller's topology. These nodes + are translated by the driver's .xlate() function. + +Required properties (port (child) node): +- #phy-cells : Should be 1 (See second example) + Cell after port phandle is device type from: + - PHY_TYPE_SATA + - PHY_TYPE_PCI +- reg : Address and length of register sets for each device in + "reg-names" +- reg-names : The names of the register addresses corresponding to the + registers filled in "reg": + - sata: For SATA devices + - pcie: For PCIe devices + +Optional properties (port (child) node): +- st,sata-gen : Generation of locally attached SATA IP. Expected values + are {1,2,3). If not supplied generation 1 hardware will + be expected +- st,pcie-tx-pol-inv : Bool property to invert the polarity PCIe Tx (Txn/Txp) +- st,sata-tx-pol-inv : Bool property to invert the polarity SATA Tx (Txn/Txp) + +Example: + + miphy365x_phy: miphy365x@fe382000 { + compatible = "st,miphy365x-phy"; + st,syscfg = <&syscfg_rear 0x824 0x828>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + phy_port0: port@fe382000 { + reg = <0xfe382000 0x100>, <0xfe394000 0x100>; + reg-names = "sata", "pcie"; + #phy-cells = <1>; + st,sata-gen = <3>; + }; + + phy_port1: port@fe38a000 { + reg = <0xfe38a000 0x100>, <0xfe804000 0x100>;; + reg-names = "sata", "pcie", "syscfg"; + #phy-cells = <1>; + st,pcie-tx-pol-inv; + }; + }; + +Specifying phy control of devices +================================= + +Device nodes should specify the configuration required in their "phys" +property, containing a phandle to the phy port node and a device type. + +Example: + +#include <dt-bindings/phy/phy.h> + + sata0: sata@fe380000 { + ... + phys = <&phy_port0 PHY_TYPE_SATA>; + ... + }; diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt new file mode 100644 index 000000000..5ffd0f55d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mvebu-comphy.txt @@ -0,0 +1,94 @@ +MVEBU comphy drivers +-------------------- + +COMPHY controllers can be found on the following Marvell MVEBU SoCs: +* Armada 7k/8k (on the CP110) +* Armada 3700 +It provides a number of shared PHYs used by various interfaces (network, SATA, +USB, PCIe...). + +Required properties: + +- compatible: should be one of: + * "marvell,comphy-cp110" for Armada 7k/8k + * "marvell,comphy-a3700" for Armada 3700 +- reg: should contain the COMPHY register(s) location(s) and length(s). + * 1 entry for Armada 7k/8k + * 4 entries for Armada 3700 along with the corresponding reg-names + properties, memory areas are: + * Generic COMPHY registers + * Lane 1 (PCIe/GbE) + * Lane 0 (USB3/GbE) + * Lane 2 (SATA/USB3) +- marvell,system-controller: should contain a phandle to the system + controller node (only for Armada 7k/8k) +- #address-cells: should be 1. +- #size-cells: should be 0. + +Optional properlties: + +- clocks: pointers to the reference clocks for this device (CP110 only), + consequently: MG clock, MG Core clock, AXI clock. +- clock-names: names of used clocks for CP110 only, must be : + "mg_clk", "mg_core_clk" and "axi_clk". + +A sub-node is required for each comphy lane provided by the comphy. + +Required properties (child nodes): + +- reg: COMPHY lane number. +- #phy-cells : from the generic PHY bindings, must be 1. Defines the + input port to use for a given comphy lane. + +Examples: + + CP11X_LABEL(comphy): phy@120000 { + compatible = "marvell,comphy-cp110"; + reg = <0x120000 0x6000>; + marvell,system-controller = <&CP11X_LABEL(syscon0)>; + clocks = <&CP11X_LABEL(clk) 1 5>, <&CP11X_LABEL(clk) 1 6>, + <&CP11X_LABEL(clk) 1 18>; + clock-names = "mg_clk", "mg_core_clk", "axi_clk"; + #address-cells = <1>; + #size-cells = <0>; + + CP11X_LABEL(comphy0): phy@0 { + reg = <0>; + #phy-cells = <1>; + }; + + CP11X_LABEL(comphy1): phy@1 { + reg = <1>; + #phy-cells = <1>; + }; + }; + + comphy: phy@18300 { + compatible = "marvell,comphy-a3700"; + reg = <0x18300 0x300>, + <0x1F000 0x400>, + <0x5C000 0x400>, + <0xe0178 0x8>; + reg-names = "comphy", + "lane1_pcie_gbe", + "lane0_usb3_gbe", + "lane2_sata_usb3"; + #address-cells = <1>; + #size-cells = <0>; + + + comphy0: phy@0 { + reg = <0>; + #phy-cells = <1>; + }; + + comphy1: phy@1 { + reg = <1>; + #phy-cells = <1>; + }; + + comphy2: phy@2 { + reg = <2>; + #phy-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-mvebu.txt b/Documentation/devicetree/bindings/phy/phy-mvebu.txt new file mode 100644 index 000000000..64afdd13d --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-mvebu.txt @@ -0,0 +1,42 @@ +* Marvell MVEBU SATA PHY + +Power control for the SATA phy found on Marvell MVEBU SoCs. + +This document extends the binding described in phy-bindings.txt + +Required properties : + + - reg : Offset and length of the register set for the SATA device + - compatible : Should be "marvell,mvebu-sata-phy" + - clocks : phandle of clock and specifier that supplies the device + - clock-names : Should be "sata" + +Example: + sata-phy@84000 { + compatible = "marvell,mvebu-sata-phy"; + reg = <0x84000 0x0334>; + clocks = <&gate_clk 15>; + clock-names = "sata"; + #phy-cells = <0>; + }; + +Armada 375 USB cluster +---------------------- + +Armada 375 comes with an USB2 host and device controller and an USB3 +controller. The USB cluster control register allows to manage common +features of both USB controllers. + +Required properties: + +- compatible: "marvell,armada-375-usb-cluster" +- reg: Should contain usb cluster register location and length. +- #phy-cells : from the generic phy bindings, must be 1. Possible +values are 1 (USB2), 2 (USB3). + +Example: + usbcluster: usb-cluster@18400 { + compatible = "marvell,armada-375-usb-cluster"; + reg = <0x18400 0x4>; + #phy-cells = <1> + }; diff --git a/Documentation/devicetree/bindings/phy/phy-pxa-usb.txt b/Documentation/devicetree/bindings/phy/phy-pxa-usb.txt new file mode 100644 index 000000000..d80e36a77 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-pxa-usb.txt @@ -0,0 +1,18 @@ +Marvell PXA USB PHY +------------------- + +Required properties: +- compatible: one of: "marvell,mmp2-usb-phy", "marvell,pxa910-usb-phy", + "marvell,pxa168-usb-phy", +- #phy-cells: must be 0 + +Example: + usb-phy: usbphy@d4207000 { + compatible = "marvell,mmp2-usb-phy"; + reg = <0xd4207000 0x40>; + #phy-cells = <0>; + status = "okay"; + }; + +This document explains the device tree binding. For general +information about PHY subsystem refer to Documentation/driver-api/phy/phy.rst diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt new file mode 100644 index 000000000..710cccd5e --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-inno-hdmi.txt @@ -0,0 +1,43 @@ +ROCKCHIP HDMI PHY WITH INNO IP BLOCK + +Required properties: + - compatible : should be one of the listed compatibles: + * "rockchip,rk3228-hdmi-phy", + * "rockchip,rk3328-hdmi-phy"; + - reg : Address and length of the hdmi phy control register set + - clocks : phandle + clock specifier for the phy clocks + - clock-names : string, clock name, must contain "sysclk" for system + control and register configuration, "refoclk" for crystal- + oscillator reference PLL clock input and "refpclk" for pclk- + based refeference PLL clock input. + - #clock-cells: should be 0. + - clock-output-names : shall be the name for the output clock. + - interrupts : phandle + interrupt specified for the hdmiphy interrupt + - #phy-cells : must be 0. See ./phy-bindings.txt for details. + +Optional properties for rk3328-hdmi-phy: + - nvmem-cells = phandle + nvmem specifier for the cpu-version efuse + - nvmem-cell-names : "cpu-version" to read the chip version, required + for adjustment to some frequency settings + +Example: + hdmi_phy: hdmi-phy@12030000 { + compatible = "rockchip,rk3228-hdmi-phy"; + reg = <0x12030000 0x10000>; + #phy-cells = <0>; + clocks = <&cru PCLK_HDMI_PHY>, <&xin24m>, <&cru DCLK_HDMIPHY>; + clock-names = "sysclk", "refoclk", "refpclk"; + #clock-cells = <0>; + clock-output-names = "hdmi_phy"; + status = "disabled"; + }; + +Then the PHY can be used in other nodes such as: + + hdmi: hdmi@200a0000 { + compatible = "rockchip,rk3228-dw-hdmi"; + ... + phys = <&hdmi_phy>; + phy-names = "hdmi"; + ... + }; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml new file mode 100644 index 000000000..d3cd79978 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-naneng-combphy.yaml @@ -0,0 +1,142 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/phy-rockchip-naneng-combphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip SoC Naneng Combo Phy + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +properties: + compatible: + enum: + - rockchip,rk3568-naneng-combphy + - rockchip,rk3588-naneng-combphy + + reg: + maxItems: 1 + + clocks: + items: + - description: reference clock + - description: apb clock + - description: pipe clock + + clock-names: + items: + - const: ref + - const: apb + - const: pipe + + resets: + minItems: 1 + maxItems: 2 + + reset-names: + minItems: 1 + items: + - const: phy + - const: apb + + rockchip,enable-ssc: + type: boolean + description: + The option SSC can be enabled for U3, SATA and PCIE. + Most commercially available platforms use SSC to reduce EMI. + + rockchip,ext-refclk: + type: boolean + description: + Many PCIe connections, especially backplane connections, + require a synchronous reference clock between the two link partners. + To achieve this a common clock source, referred to as REFCLK in + the PCI Express Card Electromechanical Specification, + should be used by both ends of the PCIe link. + In PCIe mode one can choose to use an internal or an external reference + clock. + By default the internal clock is selected. The PCIe PHY provides a 100MHz + differential clock output(optional with SSC) for system applications. + When selecting this option an externally 100MHz differential + reference clock needs to be provided to the PCIe PHY. + + rockchip,pipe-grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Some additional phy settings are accessed through GRF regs. + + rockchip,pipe-phy-grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Some additional pipe settings are accessed through GRF regs. + + "#phy-cells": + const: 1 + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - rockchip,pipe-grf + - rockchip,pipe-phy-grf + - "#phy-cells" + +allOf: + - if: + properties: + compatible: + contains: + const: rockchip,rk3568-naneng-combphy + then: + properties: + resets: + maxItems: 1 + reset-names: + maxItems: 1 + - if: + properties: + compatible: + contains: + const: rockchip,rk3588-naneng-combphy + then: + properties: + resets: + minItems: 2 + reset-names: + minItems: 2 + required: + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3568-cru.h> + + pipegrf: syscon@fdc50000 { + compatible = "rockchip,rk3568-pipe-grf", "syscon"; + reg = <0xfdc50000 0x1000>; + }; + + pipe_phy_grf0: syscon@fdc70000 { + compatible = "rockchip,rk3568-pipe-phy-grf", "syscon"; + reg = <0xfdc70000 0x1000>; + }; + + combphy0: phy@fe820000 { + compatible = "rockchip,rk3568-naneng-combphy"; + reg = <0xfe820000 0x100>; + clocks = <&pmucru CLK_PCIEPHY0_REF>, + <&cru PCLK_PIPEPHY0>, + <&cru PCLK_PIPE>; + clock-names = "ref", "apb", "pipe"; + assigned-clocks = <&pmucru CLK_PCIEPHY0_REF>; + assigned-clock-rates = <100000000>; + resets = <&cru SRST_PIPEPHY0>; + rockchip,pipe-grf = <&pipegrf>; + rockchip,pipe-phy-grf = <&pipe_phy_grf0>; + #phy-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt new file mode 100644 index 000000000..960da7fca --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt @@ -0,0 +1,84 @@ +* ROCKCHIP type-c PHY +--------------------- + +Required properties: + - compatible : must be "rockchip,rk3399-typec-phy" + - reg: Address and length of the usb phy control register set + - rockchip,grf : phandle to the syscon managing the "general + register files" + - clocks : phandle + clock specifier for the phy clocks + - clock-names : string, clock name, must be "tcpdcore", "tcpdphy-ref"; + - assigned-clocks: main clock, should be <&cru SCLK_UPHY0_TCPDCORE> or + <&cru SCLK_UPHY1_TCPDCORE>; + - assigned-clock-rates : the phy core clk frequency, shall be: 50000000 + - resets : a list of phandle + reset specifier pairs + - reset-names : string reset name, must be: + "uphy", "uphy-pipe", "uphy-tcphy" + +Optional properties: + - extcon : extcon specifier for the Power Delivery + +Required nodes : a sub-node is required for each port the phy provides. + The sub-node name is used to identify dp or usb3 port, + and shall be the following entries: + * "dp-port" : the name of DP port. + * "usb3-port" : the name of USB3 port. + +Required properties (port (child) node): +- #phy-cells : must be 0, See ./phy-bindings.txt for details. + +Deprecated properties, do not use in new device tree sources, these +properties are determined by the compatible value: + - rockchip,typec-conn-dir + - rockchip,usb3tousb2-en + - rockchip,external-psm + - rockchip,pipe-status + +Example: + tcphy0: phy@ff7c0000 { + compatible = "rockchip,rk3399-typec-phy"; + reg = <0x0 0xff7c0000 0x0 0x40000>; + rockchip,grf = <&grf>; + extcon = <&fusb0>; + clocks = <&cru SCLK_UPHY0_TCPDCORE>, + <&cru SCLK_UPHY0_TCPDPHY_REF>; + clock-names = "tcpdcore", "tcpdphy-ref"; + assigned-clocks = <&cru SCLK_UPHY0_TCPDCORE>; + assigned-clock-rates = <50000000>; + resets = <&cru SRST_UPHY0>, + <&cru SRST_UPHY0_PIPE_L00>, + <&cru SRST_P_UPHY0_TCPHY>; + reset-names = "uphy", "uphy-pipe", "uphy-tcphy"; + + tcphy0_dp: dp-port { + #phy-cells = <0>; + }; + + tcphy0_usb3: usb3-port { + #phy-cells = <0>; + }; + }; + + tcphy1: phy@ff800000 { + compatible = "rockchip,rk3399-typec-phy"; + reg = <0x0 0xff800000 0x0 0x40000>; + rockchip,grf = <&grf>; + extcon = <&fusb1>; + clocks = <&cru SCLK_UPHY1_TCPDCORE>, + <&cru SCLK_UPHY1_TCPDPHY_REF>; + clock-names = "tcpdcore", "tcpdphy-ref"; + assigned-clocks = <&cru SCLK_UPHY1_TCPDCORE>; + assigned-clock-rates = <50000000>; + resets = <&cru SRST_UPHY1>, + <&cru SRST_UPHY1_PIPE_L00>, + <&cru SRST_P_UPHY1_TCPHY>; + reset-names = "uphy", "uphy-pipe", "uphy-tcphy"; + + tcphy1_dp: dp-port { + #phy-cells = <0>; + }; + + tcphy1_usb3: usb3-port { + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt new file mode 100644 index 000000000..35f03df00 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt @@ -0,0 +1,24 @@ +ST STiH407 USB PHY controller + +This file documents the dt bindings for the usb picoPHY driver which is the PHY for both USB2 and USB3 +host controllers (when controlling usb2/1.1 devices) available on STiH407 SoC family from STMicroelectronics. + +Required properties: +- compatible : should be "st,stih407-usb2-phy" +- st,syscfg : phandle of sysconfig bank plus integer array containing phyparam and phyctrl register offsets +- resets : list of phandle and reset specifier pairs. There should be two entries, one + for the whole phy and one for the port +- reset-names : list of reset signal names. Should be "global" and "port" +See: Documentation/devicetree/bindings/reset/st,stih407-powerdown.yaml +See: Documentation/devicetree/bindings/reset/reset.txt + +Example: + +usb2_picophy0: usbpicophy@f8 { + compatible = "st,stih407-usb2-phy"; + #phy-cells = <0>; + st,syscfg = <&syscfg_core 0x100 0xf4>; + resets = <&softreset STIH407_PICOPHY_SOFTRESET>, + <&picophyreset STIH407_PICOPHY0_RESET>; + reset-names = "global", "port"; +}; diff --git a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml new file mode 100644 index 000000000..24a3dbde2 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml @@ -0,0 +1,282 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/phy-stm32-usbphyc.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: STMicroelectronics STM32 USB HS PHY controller + +description: + + The STM32 USBPHYC block contains a dual port High Speed UTMI+ PHY and a UTMI + switch. It controls PHY configuration and status, and the UTMI+ switch that + selects either OTG or HOST controller for the second PHY port. It also sets + PLL configuration. + + USBPHYC + |_ PLL + | + |_ PHY port#1 _________________ HOST controller + | __ | + | / 1|________________| + |_ PHY port#2 ----| |________________ + | \_0| | + |_ UTMI switch_______| OTG controller + +maintainers: + - Amelie Delaunay <amelie.delaunay@foss.st.com> + +properties: + compatible: + const: st,stm32mp1-usbphyc + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + vdda1v1-supply: + description: regulator providing 1V1 power supply to the PLL block + + vdda1v8-supply: + description: regulator providing 1V8 power supply to the PLL block + + '#clock-cells': + description: number of clock cells for ck_usbo_48m consumer + const: 0 + +# Required child nodes: + +patternProperties: + "^usb-phy@[0|1]$": + type: object + description: + Each port the controller provides must be represented as a sub-node. + + properties: + reg: + description: phy port index. + maxItems: 1 + + phy-supply: + description: regulator providing 3V3 power supply to the PHY. + + "#phy-cells": + enum: [ 0x0, 0x1 ] + + connector: + type: object + $ref: /schemas/connector/usb-connector.yaml + unevaluatedProperties: false + + properties: + vbus-supply: true + + # It can be necessary to adjust the PHY settings to compensate parasitics, which can be due + # to USB connector/receptacle, routing, ESD protection component,... Here is the list of + # all optional parameters to tune the interface of the PHY (HS for High-Speed, FS for Full- + # Speed, LS for Low-Speed) + + st,current-boost-microamp: + description: Current boosting in uA + enum: [ 1000, 2000 ] + + st,no-lsfs-fb-cap: + description: Disables the LS/FS feedback capacitor + type: boolean + + st,decrease-hs-slew-rate: + description: Decreases the HS driver slew rate by 10% + type: boolean + + st,tune-hs-dc-level: + description: | + Tunes the HS driver DC level + - <0> normal level + - <1> increases the level by 5 to 7 mV + - <2> increases the level by 10 to 14 mV + - <3> decreases the level by 5 to 7 mV + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 0 + + st,enable-fs-rftime-tuning: + description: Enables the FS rise/fall tuning option + type: boolean + + st,enable-hs-rftime-reduction: + description: Enables the HS rise/fall reduction feature + type: boolean + + st,trim-hs-current: + description: | + Controls HS driver current trimming for choke compensation + - <0> = 18.87 mA target current / nominal + 0% + - <1> = 19.165 mA target current / nominal + 1.56% + - <2> = 19.46 mA target current / nominal + 3.12% + - <3> = 19.755 mA target current / nominal + 4.68% + - <4> = 20.05 mA target current / nominal + 6.24% + - <5> = 20.345 mA target current / nominal + 7.8% + - <6> = 20.64 mA target current / nominal + 9.36% + - <7> = 20.935 mA target current / nominal + 10.92% + - <8> = 21.23 mA target current / nominal + 12.48% + - <9> = 21.525 mA target current / nominal + 14.04% + - <10> = 21.82 mA target current / nominal + 15.6% + - <11> = 22.115 mA target current / nominal + 17.16% + - <12> = 22.458 mA target current / nominal + 19.01% + - <13> = 22.755 mA target current / nominal + 20.58% + - <14> = 23.052 mA target current / nominal + 22.16% + - <15> = 23.348 mA target current / nominal + 23.73% + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + default: 0 + + st,trim-hs-impedance: + description: | + Controls HS driver impedance tuning for choke compensation + - <0> = no impedance offset + - <1> = reduce the impedance by 2 ohms + - <2> = reduce the impedance by 4 ohms + - <3> = reduce the impedance by 6 ohms + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 0 + + st,tune-squelch-level: + description: | + Tunes the squelch DC threshold value + - <0> = no shift in threshold + - <1> = threshold shift by +7 mV + - <2> = threshold shift by -5 mV + - <3> = threshold shift by +14 mV + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 0 + + st,enable-hs-rx-gain-eq: + description: Enables the HS Rx gain equalizer + type: boolean + + st,tune-hs-rx-offset: + description: | + Adjusts the HS Rx offset + - <0> = no offset + - <1> = offset of +5 mV + - <2> = offset of +10 mV + - <3> = offset of -5 mV + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 0 + + st,no-hs-ftime-ctrl: + description: Disables the HS fall time control of single ended signals during pre-emphasis + type: boolean + + st,no-lsfs-sc: + description: Disables the short circuit protection in LS/FS driver + type: boolean + + st,enable-hs-tx-staggering: + description: Enables the basic staggering in HS Tx mode + type: boolean + + allOf: + - if: + properties: + reg: + const: 0 + then: + properties: + "#phy-cells": + const: 0 + else: + properties: + "#phy-cells": + const: 1 + description: + The value is used to select UTMI switch output. + 0 for OTG controller and 1 for Host controller. + + required: + - reg + - phy-supply + - "#phy-cells" + + additionalProperties: false + +required: + - compatible + - reg + - clocks + - "#address-cells" + - "#size-cells" + - vdda1v1-supply + - vdda1v8-supply + - usb-phy@0 + - usb-phy@1 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/stm32mp1-clks.h> + #include <dt-bindings/reset/stm32mp1-resets.h> + usbphyc: usbphyc@5a006000 { + compatible = "st,stm32mp1-usbphyc"; + reg = <0x5a006000 0x1000>; + clocks = <&rcc USBPHY_K>; + resets = <&rcc USBPHY_R>; + vdda1v1-supply = <®11>; + vdda1v8-supply = <®18>; + #address-cells = <1>; + #size-cells = <0>; + #clock-cells = <0>; + + usbphyc_port0: usb-phy@0 { + reg = <0>; + phy-supply = <&vdd_usb>; + #phy-cells = <0>; + st,tune-hs-dc-level = <2>; + st,enable-fs-rftime-tuning; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <15>; + st,trim-hs-impedance = <1>; + st,tune-squelch-level = <3>; + st,tune-hs-rx-offset = <2>; + st,no-lsfs-sc; + connector { + compatible = "usb-a-connector"; + vbus-supply = <&vbus_sw>; + }; + }; + + usbphyc_port1: usb-phy@1 { + reg = <1>; + phy-supply = <&vdd_usb>; + #phy-cells = <1>; + st,tune-hs-dc-level = <2>; + st,enable-fs-rftime-tuning; + st,enable-hs-rftime-reduction; + st,trim-hs-current = <15>; + st,trim-hs-impedance = <1>; + st,tune-squelch-level = <3>; + st,tune-hs-rx-offset = <2>; + st,no-lsfs-sc; + }; + }; +... diff --git a/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.yaml b/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.yaml new file mode 100644 index 000000000..4790c6238 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-tegra194-p2u.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/phy-tegra194-p2u.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: NVIDIA Tegra194 & Tegra234 P2U + +maintainers: + - Thierry Reding <treding@nvidia.com> + +description: > + Tegra194 has two PHY bricks namely HSIO (High Speed IO) and NVHS (NVIDIA High + Speed) each interfacing with 12 and 8 P2U instances respectively. + Tegra234 has three PHY bricks namely HSIO, NVHS and GBE (Gigabit Ethernet) + each interfacing with 8, 8 and 8 P2U instances respectively. + A P2U instance is a glue logic between Synopsys DesignWare Core PCIe IP's PIPE + interface and PHY of HSIO/NVHS/GBE bricks. Each P2U instance represents one + PCIe lane. + +properties: + compatible: + enum: + - nvidia,tegra194-p2u + - nvidia,tegra234-p2u + + reg: + maxItems: 1 + description: Should be the physical address space and length of respective each P2U instance. + + reg-names: + items: + - const: ctl + + nvidia,skip-sz-protect-en: + description: Should be present if two PCIe retimers are present between + the root port and its immediate downstream device. + type: boolean + + '#phy-cells': + const: 0 + +additionalProperties: false + +examples: + - | + p2u_hsio_0: phy@3e10000 { + compatible = "nvidia,tegra194-p2u"; + reg = <0x03e10000 0x10000>; + reg-names = "ctl"; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/pistachio-usb-phy.txt b/Documentation/devicetree/bindings/phy/pistachio-usb-phy.txt new file mode 100644 index 000000000..c7970c07e --- /dev/null +++ b/Documentation/devicetree/bindings/phy/pistachio-usb-phy.txt @@ -0,0 +1,29 @@ +IMG Pistachio USB PHY +===================== + +Required properties: +-------------------- + - compatible: Must be "img,pistachio-usb-phy". + - #phy-cells: Must be 0. See ./phy-bindings.txt for details. + - clocks: Must contain an entry for each entry in clock-names. + See ../clock/clock-bindings.txt for details. + - clock-names: Must include "usb_phy". + - img,cr-top: Must contain a phandle to the CR_TOP syscon node. + - img,refclk: Indicates the reference clock source for the USB PHY. + See <dt-bindings/phy/phy-pistachio-usb.h> for a list of valid values. + +Optional properties: +-------------------- + - phy-supply: USB VBUS supply. Must supply 5.0V. + +Example: +-------- +usb_phy: usb-phy { + compatible = "img,pistachio-usb-phy"; + clocks = <&clk_core CLK_USB_PHY>; + clock-names = "usb_phy"; + phy-supply = <&usb_vbus>; + img,refclk = <REFCLK_CLK_CORE>; + img,cr-top = <&cr_top>; + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/phy/pxa1928-usb-phy.txt b/Documentation/devicetree/bindings/phy/pxa1928-usb-phy.txt new file mode 100644 index 000000000..da94426aa --- /dev/null +++ b/Documentation/devicetree/bindings/phy/pxa1928-usb-phy.txt @@ -0,0 +1,18 @@ +* Marvell PXA1928 USB and HSIC PHYs + +Required properties: +- compatible: "marvell,pxa1928-usb-phy" or "marvell,pxa1928-hsic-phy" +- reg: base address and length of the registers +- clocks - A single clock. From common clock binding. +- #phys-cells: should be 0. From common phy binding. +- resets: reference to the reset controller + +Example: + + usbphy: phy@7000 { + compatible = "marvell,pxa1928-usb-phy"; + reg = <0x7000 0xe0>; + clocks = <&apmu_clocks PXA1928_CLK_USB>; + #phy-cells = <0>; + }; + diff --git a/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml new file mode 100644 index 000000000..6566353f1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,edp-phy.yaml @@ -0,0 +1,80 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) + +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,edp-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm eDP PHY + +maintainers: + - Bjorn Andersson <bjorn.andersson@linaro.org> + +description: + The Qualcomm eDP PHY is found in a number of Qualcomm platform and provides + the physical interface for Embedded Display Port. + +properties: + compatible: + enum: + - qcom,sc7280-edp-phy + - qcom,sc8180x-edp-phy + - qcom,sc8280xp-dp-phy + - qcom,sc8280xp-edp-phy + + reg: + items: + - description: PHY base register block + - description: tx0 register block + - description: tx1 register block + - description: PLL register block + + clocks: + maxItems: 2 + + clock-names: + items: + - const: aux + - const: cfg_ahb + + "#clock-cells": + const: 1 + + "#phy-cells": + const: 0 + + power-domains: + maxItems: 1 + + vdda-phy-supply: true + vdda-pll-supply: true + +required: + - compatible + - reg + - clocks + - clock-names + - "#clock-cells" + - "#phy-cells" + +additionalProperties: false + +examples: + - | + phy@aec2a00 { + compatible = "qcom,sc8180x-edp-phy"; + reg = <0x0aec2a00 0x1c0>, + <0x0aec2200 0xa0>, + <0x0aec2600 0xa0>, + <0x0aec2000 0x19c>; + + clocks = <&dispcc 0>, <&dispcc 1>; + clock-names = "aux", "cfg_ahb"; + + #clock-cells = <1>; + #phy-cells = <0>; + + vdda-phy-supply = <&vdd_a_edp_0_1p2>; + vdda-pll-supply = <&vdd_a_edp_0_0p9>; + }; +... diff --git a/Documentation/devicetree/bindings/phy/qcom,hdmi-phy-other.yaml b/Documentation/devicetree/bindings/phy/qcom,hdmi-phy-other.yaml new file mode 100644 index 000000000..0c8f03b78 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,hdmi-phy-other.yaml @@ -0,0 +1,125 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/phy/qcom,hdmi-phy-other.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Adreno/Snapdragon HDMI phy + +maintainers: + - Rob Clark <robdclark@gmail.com> + +properties: + compatible: + enum: + - qcom,hdmi-phy-8660 + - qcom,hdmi-phy-8960 + - qcom,hdmi-phy-8974 + - qcom,hdmi-phy-8084 + + reg: + maxItems: 2 + + reg-names: + items: + - const: hdmi_phy + - const: hdmi_pll + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + maxItems: 2 + + power-domains: + maxItems: 1 + + core-vdda-supply: + description: phandle to VDDA supply regulator + + vddio-supply: + description: phandle to VDD I/O supply regulator + + '#clock-cells': + const: 0 + + '#phy-cells': + const: 0 + +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,hdmi-phy-8660 + then: + properties: + clocks: + maxItems: 1 + clock-names: + items: + - const: slave_iface + vddio-supply: false + + - if: + properties: + compatible: + contains: + enum: + - qcom,hdmi-phy-8960 + then: + properties: + clocks: + minItems: 1 + maxItems: 2 + clock-names: + minItems: 1 + items: + - const: slave_iface + - const: pxo + vddio-supply: false + + - if: + properties: + compatible: + contains: + enum: + - qcom,hdmi-phy-8084 + - qcom,hdmi-phy-8974 + then: + properties: + clocks: + maxItems: 2 + clock-names: + items: + - const: iface + - const: alt_iface + +required: + - compatible + - clocks + - reg + - reg-names + - '#phy-cells' + +additionalProperties: false + +examples: + - | + hdmi_phy: phy@4a00400 { + compatible = "qcom,hdmi-phy-8960"; + reg-names = "hdmi_phy", + "hdmi_pll"; + reg = <0x4a00400 0x60>, + <0x4a00500 0x100>; + #clock-cells = <0>; + #phy-cells = <0>; + power-domains = <&mmcc 1>; + clock-names = "slave_iface", "pxo"; + clocks = <&clk 21>, <&pxo_board>; + core-vdda-supply = <&pm8921_hdmi_mvs>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,hdmi-phy-qmp.yaml b/Documentation/devicetree/bindings/phy/qcom,hdmi-phy-qmp.yaml new file mode 100644 index 000000000..83fe4b39b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,hdmi-phy-qmp.yaml @@ -0,0 +1,94 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- + +$id: http://devicetree.org/schemas/phy/qcom,hdmi-phy-qmp.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Adreno/Snapdragon QMP HDMI phy + +maintainers: + - Rob Clark <robdclark@gmail.com> + +properties: + compatible: + enum: + - qcom,hdmi-phy-8996 + + reg: + maxItems: 6 + + reg-names: + items: + - const: hdmi_pll + - const: hdmi_tx_l0 + - const: hdmi_tx_l1 + - const: hdmi_tx_l2 + - const: hdmi_tx_l3 + - const: hdmi_phy + + clocks: + minItems: 2 + maxItems: 3 + + clock-names: + minItems: 2 + items: + - const: iface + - const: ref + - const: xo + + power-domains: + maxItems: 1 + + vcca-supply: + description: phandle to VCCA supply regulator + + vddio-supply: + description: phandle to VDD I/O supply regulator + + '#clock-cells': + const: 0 + + '#phy-cells': + const: 0 + +required: + - compatible + - clocks + - clock-names + - reg + - reg-names + - '#phy-cells' + +additionalProperties: false + +examples: + - | + hdmi-phy@9a0600 { + compatible = "qcom,hdmi-phy-8996"; + reg = <0x009a0600 0x1c4>, + <0x009a0a00 0x124>, + <0x009a0c00 0x124>, + <0x009a0e00 0x124>, + <0x009a1000 0x124>, + <0x009a1200 0x0c8>; + reg-names = "hdmi_pll", + "hdmi_tx_l0", + "hdmi_tx_l1", + "hdmi_tx_l2", + "hdmi_tx_l3", + "hdmi_phy"; + + clocks = <&mmcc 116>, + <&gcc 214>, + <&xo_board>; + clock-names = "iface", + "ref", + "xo"; + #clock-cells = <0>; + #phy-cells = <0>; + + vddio-supply = <&vreg_l12a_1p8>; + vcca-supply = <&vreg_l28a_0p925>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml b/Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml new file mode 100644 index 000000000..2671a048c --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,ipq5332-usb-hsphy.yaml @@ -0,0 +1,59 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,ipq5332-usb-hsphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: M31 USB PHY + +maintainers: + - Sricharan Ramabadhran <quic_srichara@quicinc.com> + - Varadarajan Narayanan <quic_varada@quicinc.com> + +description: + USB M31 PHY (https://www.m31tech.com) found in Qualcomm + IPQ5018, IPQ5332 SoCs. + +properties: + compatible: + items: + - const: qcom,ipq5332-usb-hsphy + + "#phy-cells": + const: 0 + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: cfg_ahb + + resets: + maxItems: 1 + + vdd-supply: + description: + Phandle to 5V regulator supply to PHY digital circuit. + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,ipq5332-gcc.h> + usb-phy@7b000 { + compatible = "qcom,ipq5332-usb-hsphy"; + reg = <0x0007b000 0x12c>; + + clocks = <&gcc GCC_USB0_PHY_CFG_AHB_CLK>; + clock-names = "cfg_ahb"; + + #phy-cells = <0>; + + resets = <&gcc GCC_QUSB2_0_PHY_BCR>; + + vdd-supply = <®ulator_fixed_5p0>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,ipq806x-usb-phy-hs.yaml b/Documentation/devicetree/bindings/phy/qcom,ipq806x-usb-phy-hs.yaml new file mode 100644 index 000000000..35296c588 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,ipq806x-usb-phy-hs.yaml @@ -0,0 +1,56 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,ipq806x-usb-phy-hs.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm ipq806x usb DWC3 HS PHY CONTROLLER + +maintainers: + - Ansuel Smith <ansuelsmth@gmail.com> + +description: + DWC3 PHY nodes are defined to describe on-chip Synopsis Physical layer + controllers used in ipq806x. Each DWC3 PHY controller should have its + own node. + +properties: + compatible: + const: qcom,ipq806x-usb-phy-hs + + "#phy-cells": + const: 0 + + reg: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: ref + - const: xo + +required: + - compatible + - "#phy-cells" + - reg + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-ipq806x.h> + + hs_phy_0: phy@110f8800 { + compatible = "qcom,ipq806x-usb-phy-hs"; + reg = <0x110f8800 0x30>; + clocks = <&gcc USB30_0_UTMI_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,ipq806x-usb-phy-ss.yaml b/Documentation/devicetree/bindings/phy/qcom,ipq806x-usb-phy-ss.yaml new file mode 100644 index 000000000..6cf5c6c06 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,ipq806x-usb-phy-ss.yaml @@ -0,0 +1,74 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,ipq806x-usb-phy-ss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm ipq806x usb DWC3 SS PHY CONTROLLER + +maintainers: + - Ansuel Smith <ansuelsmth@gmail.com> + +description: + DWC3 PHY nodes are defined to describe on-chip Synopsis Physical layer + controllers used in ipq806x. Each DWC3 PHY controller should have its + own node. + +properties: + compatible: + const: qcom,ipq806x-usb-phy-ss + + "#phy-cells": + const: 0 + + reg: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: ref + - const: xo + + qcom,rx-eq: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Override value for rx_eq. + default: 4 + maximum: 7 + + qcom,tx-deamp-3_5db: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Override value for transmit preemphasis. + default: 23 + maximum: 63 + + qcom,mpll: + $ref: /schemas/types.yaml#/definitions/uint32 + description: Override value for mpll. + default: 0 + maximum: 7 + +required: + - compatible + - "#phy-cells" + - reg + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-ipq806x.h> + + ss_phy_0: phy@110f8830 { + compatible = "qcom,ipq806x-usb-phy-ss"; + reg = <0x110f8830 0x30>; + clocks = <&gcc USB30_0_MASTER_CLK>; + clock-names = "ref"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,ipq8074-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,ipq8074-qmp-pcie-phy.yaml new file mode 100644 index 000000000..634cec5d5 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,ipq8074-qmp-pcie-phy.yaml @@ -0,0 +1,91 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,ipq8074-qmp-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QMP PHY controller (PCIe, IPQ8074) + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +description: + QMP PHY controller supports physical layer functionality for a number of + controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB. + +properties: + compatible: + enum: + - qcom,ipq6018-qmp-pcie-phy + - qcom,ipq8074-qmp-gen3-pcie-phy + - qcom,ipq8074-qmp-pcie-phy + + reg: + items: + - description: serdes + + clocks: + maxItems: 3 + + clock-names: + items: + - const: aux + - const: cfg_ahb + - const: pipe + + resets: + maxItems: 2 + + reset-names: + items: + - const: phy + - const: common + + "#clock-cells": + const: 0 + + clock-output-names: + maxItems: 1 + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - "#clock-cells" + - clock-output-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-ipq6018.h> + #include <dt-bindings/reset/qcom,gcc-ipq6018.h> + + phy@84000 { + compatible = "qcom,ipq6018-qmp-pcie-phy"; + reg = <0x00084000 0x1000>; + + clocks = <&gcc GCC_PCIE0_AUX_CLK>, + <&gcc GCC_PCIE0_AHB_CLK>, + <&gcc GCC_PCIE0_PIPE_CLK>; + clock-names = "aux", + "cfg_ahb", + "pipe"; + + clock-output-names = "gcc_pcie0_pipe_clk_src"; + #clock-cells = <0>; + + #phy-cells = <0>; + + resets = <&gcc GCC_PCIE0_PHY_BCR>, + <&gcc GCC_PCIE0PHY_PHY_BCR>; + reset-names = "phy", + "common"; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,msm8996-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,msm8996-qmp-pcie-phy.yaml new file mode 100644 index 000000000..4e710ef75 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,msm8996-qmp-pcie-phy.yaml @@ -0,0 +1,189 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,msm8996-qmp-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QMP PHY controller (MSM8996 PCIe) + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +description: + QMP PHY controller supports physical layer functionality for a number of + controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB. + +properties: + compatible: + const: qcom,msm8996-qmp-pcie-phy + + reg: + items: + - description: serdes + + "#address-cells": + enum: [ 1, 2 ] + + "#size-cells": + enum: [ 1, 2 ] + + ranges: true + + clocks: + maxItems: 3 + + clock-names: + items: + - const: aux + - const: cfg_ahb + - const: ref + + resets: + maxItems: 3 + + reset-names: + items: + - const: phy + - const: common + - const: cfg + + vdda-phy-supply: true + + vdda-pll-supply: true + + vddp-ref-clk-supply: true + +patternProperties: + "^phy@[0-9a-f]+$": + type: object + description: one child node per PHY provided by this block + properties: + reg: + items: + - description: TX + - description: RX + - description: PCS + + clocks: + items: + - description: PIPE clock + + clock-names: + deprecated: true + items: + - enum: + - pipe0 + - pipe1 + - pipe2 + + resets: + items: + - description: PHY reset + + reset-names: + deprecated: true + items: + - enum: + - lane0 + - lane1 + - lane2 + + "#clock-cells": + const: 0 + + clock-output-names: + maxItems: 1 + + "#phy-cells": + const: 0 + + required: + - reg + - clocks + - resets + - "#clock-cells" + - clock-output-names + - "#phy-cells" + + additionalProperties: false + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - ranges + - clocks + - clock-names + - resets + - reset-names + - vdda-phy-supply + - vdda-pll-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-msm8996.h> + pcie_phy: phy-wrapper@34000 { + compatible = "qcom,msm8996-qmp-pcie-phy"; + reg = <0x34000 0x488>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x34000 0x4000>; + + clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, + <&gcc GCC_PCIE_PHY_CFG_AHB_CLK>, + <&gcc GCC_PCIE_CLKREF_CLK>; + clock-names = "aux", "cfg_ahb", "ref"; + + resets = <&gcc GCC_PCIE_PHY_BCR>, + <&gcc GCC_PCIE_PHY_COM_BCR>, + <&gcc GCC_PCIE_PHY_COM_NOCSR_BCR>; + reset-names = "phy", "common", "cfg"; + + vdda-phy-supply = <&vreg_l28a_0p925>; + vdda-pll-supply = <&vreg_l12a_1p8>; + + pciephy_0: phy@1000 { + reg = <0x1000 0x130>, + <0x1200 0x200>, + <0x1400 0x1dc>; + + clocks = <&gcc GCC_PCIE_0_PIPE_CLK>; + resets = <&gcc GCC_PCIE_0_PHY_BCR>; + + #clock-cells = <0>; + clock-output-names = "pcie_0_pipe_clk_src"; + + #phy-cells = <0>; + }; + + pciephy_1: phy@2000 { + reg = <0x2000 0x130>, + <0x2200 0x200>, + <0x2400 0x1dc>; + + clocks = <&gcc GCC_PCIE_1_PIPE_CLK>; + resets = <&gcc GCC_PCIE_1_PHY_BCR>; + + #clock-cells = <0>; + clock-output-names = "pcie_1_pipe_clk_src"; + + #phy-cells = <0>; + }; + + pciephy_2: phy@3000 { + reg = <0x3000 0x130>, + <0x3200 0x200>, + <0x3400 0x1dc>; + + clocks = <&gcc GCC_PCIE_2_PIPE_CLK>; + resets = <&gcc GCC_PCIE_2_PHY_BCR>; + + #clock-cells = <0>; + clock-output-names = "pcie_2_pipe_clk_src"; + + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,msm8996-qmp-usb3-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,msm8996-qmp-usb3-phy.yaml new file mode 100644 index 000000000..827109d37 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,msm8996-qmp-usb3-phy.yaml @@ -0,0 +1,287 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,msm8996-qmp-usb3-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QMP PHY controller (USB, MSM8996) + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +description: + QMP PHY controller supports physical layer functionality for a number of + controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB. + + Note that these bindings are for SoCs up to SC8180X. For newer SoCs, see + qcom,sc8280xp-qmp-usb3-uni-phy.yaml. + +properties: + compatible: + enum: + - qcom,ipq6018-qmp-usb3-phy + - qcom,ipq8074-qmp-usb3-phy + - qcom,msm8996-qmp-usb3-phy + - qcom,msm8998-qmp-usb3-phy + - qcom,sdm845-qmp-usb3-uni-phy + - qcom,sdx55-qmp-usb3-uni-phy + - qcom,sdx65-qmp-usb3-uni-phy + - qcom,sm8150-qmp-usb3-uni-phy + - qcom,sm8250-qmp-usb3-uni-phy + - qcom,sm8350-qmp-usb3-uni-phy + + reg: + items: + - description: serdes + + "#address-cells": + enum: [ 1, 2 ] + + "#size-cells": + enum: [ 1, 2 ] + + ranges: true + + clocks: + minItems: 3 + maxItems: 4 + + clock-names: + minItems: 3 + maxItems: 4 + + power-domains: + maxItems: 1 + + resets: + maxItems: 2 + + reset-names: + maxItems: 2 + + vdda-phy-supply: true + + vdda-pll-supply: true + + vddp-ref-clk-supply: true + +patternProperties: + "^phy@[0-9a-f]+$": + type: object + description: single PHY-provider child node + properties: + reg: + minItems: 3 + maxItems: 6 + + clocks: + items: + - description: PIPE clock + + clock-names: + deprecated: true + items: + - const: pipe0 + + "#clock-cells": + const: 0 + + clock-output-names: + maxItems: 1 + + "#phy-cells": + const: 0 + + required: + - reg + - clocks + - "#clock-cells" + - clock-output-names + - "#phy-cells" + + additionalProperties: false + +required: + - compatible + - reg + - "#address-cells" + - "#size-cells" + - ranges + - clocks + - clock-names + - resets + - reset-names + - vdda-phy-supply + - vdda-pll-supply + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,sdm845-qmp-usb3-uni-phy + then: + properties: + clocks: + maxItems: 4 + clock-names: + items: + - const: aux + - const: cfg_ahb + - const: ref + - const: com_aux + resets: + maxItems: 2 + reset-names: + items: + - const: phy + - const: common + + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq8074-qmp-usb3-phy + - qcom,msm8996-qmp-usb3-phy + - qcom,msm8998-qmp-usb3-phy + - qcom,sdx55-qmp-usb3-uni-phy + - qcom,sdx65-qmp-usb3-uni-phy + then: + properties: + clocks: + maxItems: 3 + clock-names: + items: + - const: aux + - const: cfg_ahb + - const: ref + resets: + maxItems: 2 + reset-names: + items: + - const: phy + - const: common + + - if: + properties: + compatible: + contains: + enum: + - qcom,sm8150-qmp-usb3-uni-phy + - qcom,sm8250-qmp-usb3-uni-phy + - qcom,sm8350-qmp-usb3-uni-phy + then: + properties: + clocks: + maxItems: 4 + clock-names: + items: + - const: aux + - const: ref_clk_src + - const: ref + - const: com_aux + resets: + maxItems: 2 + reset-names: + items: + - const: phy + - const: common + + - if: + properties: + compatible: + contains: + enum: + - qcom,msm8998-qmp-usb3-phy + then: + patternProperties: + "^phy@[0-9a-f]+$": + properties: + reg: + items: + - description: TX lane 1 + - description: RX lane 1 + - description: PCS + - description: TX lane 2 + - description: RX lane 2 + + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq6018-qmp-usb3-phy + - qcom,ipq8074-qmp-usb3-phy + - qcom,sdx55-qmp-usb3-uni-phy + - qcom,sdx65-qmp-usb3-uni-phy + - qcom,sm8150-qmp-usb3-uni-phy + then: + patternProperties: + "^phy@[0-9a-f]+$": + properties: + reg: + items: + - description: TX + - description: RX + - description: PCS + - description: PCS_MISC + + - if: + properties: + compatible: + contains: + enum: + - qcom,msm8996-qmp-usb3-phy + - qcom,sm8250-qmp-usb3-uni-phy + - qcom,sm8350-qmp-usb3-uni-phy + then: + patternProperties: + "^phy@[0-9a-f]+$": + properties: + reg: + items: + - description: TX + - description: RX + - description: PCS + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-sdm845.h> + usb_2_qmpphy: phy-wrapper@88eb000 { + compatible = "qcom,sdm845-qmp-usb3-uni-phy"; + reg = <0x088eb000 0x18c>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x088eb000 0x2000>; + + clocks = <&gcc GCC_USB3_SEC_PHY_AUX_CLK >, + <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, + <&gcc GCC_USB3_SEC_CLKREF_CLK>, + <&gcc GCC_USB3_SEC_PHY_COM_AUX_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "com_aux"; + + resets = <&gcc GCC_USB3PHY_PHY_SEC_BCR>, + <&gcc GCC_USB3_PHY_SEC_BCR>; + reset-names = "phy", "common"; + + vdda-phy-supply = <&vdda_usb2_ss_1p2>; + vdda-pll-supply = <&vdda_usb2_ss_core>; + + usb_2_ssphy: phy@200 { + reg = <0x200 0x128>, + <0x400 0x1fc>, + <0x800 0x218>, + <0x600 0x70>; + + clocks = <&gcc GCC_USB3_SEC_PHY_PIPE_CLK>; + + #clock-cells = <0>; + clock-output-names = "usb3_uni_phy_pipe_clk_src"; + + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,msm8998-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,msm8998-qmp-pcie-phy.yaml new file mode 100644 index 000000000..d05eef0e1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,msm8998-qmp-pcie-phy.yaml @@ -0,0 +1,97 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,msm8998-qmp-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QMP PHY controller (PCIe, MSM8998) + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +description: + The QMP PHY controller supports physical layer functionality for a number of + controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB. + +properties: + compatible: + const: qcom,msm8998-qmp-pcie-phy + + reg: + items: + - description: serdes + + clocks: + maxItems: 4 + + clock-names: + items: + - const: aux + - const: cfg_ahb + - const: ref + - const: pipe + + resets: + maxItems: 2 + + reset-names: + items: + - const: phy + - const: common + + vdda-phy-supply: true + + vdda-pll-supply: true + + "#clock-cells": + const: 0 + + clock-output-names: + maxItems: 1 + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - vdda-phy-supply + - vdda-pll-supply + - "#clock-cells" + - clock-output-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-msm8998.h> + + phy@1c18000 { + compatible = "qcom,msm8998-qmp-pcie-phy"; + reg = <0x01c06000 0x1000>; + + clocks = <&gcc GCC_PCIE_PHY_AUX_CLK>, + <&gcc GCC_PCIE_0_CFG_AHB_CLK>, + <&gcc GCC_PCIE_CLKREF_CLK>, + <&gcc GCC_PCIE_0_PIPE_CLK>; + clock-names = "aux", + "cfg_ahb", + "ref", + "pipe"; + + clock-output-names = "pcie_0_pipe_clk_src"; + #clock-cells = <0>; + + #phy-cells = <0>; + + resets = <&gcc GCC_PCIE_0_PHY_BCR>, <&gcc GCC_PCIE_PHY_BCR>; + reset-names = "phy", "common"; + + vdda-phy-supply = <&vreg_l1a_0p875>; + vdda-pll-supply = <&vreg_l2a_1p2>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,pcie2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,pcie2-phy.yaml new file mode 100644 index 000000000..dbc4a4c71 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,pcie2-phy.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,pcie2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm PCIe2 PHY controller + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +description: + The Qualcomm PCIe2 PHY is a Synopsys based phy found in a number of Qualcomm + platforms. + +properties: + compatible: + items: + - const: qcom,qcs404-pcie2-phy + - const: qcom,pcie2-phy + + reg: + items: + - description: PHY register set + + clocks: + items: + - description: a clock-specifier pair for the "pipe" clock + + clock-output-names: + maxItems: 1 + + "#clock-cells": + const: 0 + + "#phy-cells": + const: 0 + + vdda-vp-supply: + description: low voltage regulator + + vdda-vph-supply: + description: high voltage regulator + + resets: + maxItems: 2 + + reset-names: + items: + - const: phy + - const: pipe + +required: + - compatible + - reg + - clocks + - clock-output-names + - "#clock-cells" + - "#phy-cells" + - vdda-vp-supply + - vdda-vph-supply + - resets + - reset-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-qcs404.h> + phy@7786000 { + compatible = "qcom,qcs404-pcie2-phy", "qcom,pcie2-phy"; + reg = <0x07786000 0xb8>; + + clocks = <&gcc GCC_PCIE_0_PIPE_CLK>; + resets = <&gcc GCC_PCIEPHY_0_PHY_BCR>, + <&gcc GCC_PCIE_0_PIPE_ARES>; + reset-names = "phy", "pipe"; + + vdda-vp-supply = <&vreg_l3_1p05>; + vdda-vph-supply = <&vreg_l5_1p8>; + + clock-output-names = "pcie_0_pipe_clk"; + #clock-cells = <0>; + #phy-cells = <0>; + }; +... diff --git a/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml new file mode 100644 index 000000000..95eecbaef --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,qusb2-phy.yaml @@ -0,0 +1,203 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) + +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,qusb2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QUSB2 phy controller + +maintainers: + - Wesley Cheng <quic_wcheng@quicinc.com> + +description: + QUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets. + +properties: + compatible: + oneOf: + - items: + - enum: + - qcom,ipq6018-qusb2-phy + - qcom,ipq8074-qusb2-phy + - qcom,ipq9574-qusb2-phy + - qcom,msm8953-qusb2-phy + - qcom,msm8996-qusb2-phy + - qcom,msm8998-qusb2-phy + - qcom,qcm2290-qusb2-phy + - qcom,sdm660-qusb2-phy + - qcom,sm4250-qusb2-phy + - qcom,sm6115-qusb2-phy + - items: + - enum: + - qcom,sc7180-qusb2-phy + - qcom,sdm670-qusb2-phy + - qcom,sdm845-qusb2-phy + - qcom,sm6350-qusb2-phy + - const: qcom,qusb2-v2-phy + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + minItems: 2 + items: + - description: phy config clock + - description: 19.2 MHz ref clk + - description: phy interface clock (Optional) + + clock-names: + minItems: 2 + items: + - const: cfg_ahb + - const: ref + - const: iface + + vdd-supply: + description: + Phandle to 0.9V regulator supply to PHY digital circuit. + + vdda-pll-supply: + description: + Phandle to 1.8V regulator supply to PHY refclk pll block. + + vdda-phy-dpdm-supply: + description: + Phandle to 3.1V regulator supply to Dp/Dm port signals. + + resets: + maxItems: 1 + description: + Phandle to reset to phy block. + + nvmem-cells: + maxItems: 1 + description: + Phandle to nvmem cell that contains 'HS Tx trim' + tuning parameter value for qusb2 phy. + + qcom,tcsr-syscon: + description: + Phandle to TCSR syscon register region. + $ref: /schemas/types.yaml#/definitions/phandle + + qcom,imp-res-offset-value: + description: + It is a 6 bit value that specifies offset to be + added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY + tuning parameter that may vary for different boards of same SOC. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 63 + default: 0 + + qcom,bias-ctrl-value: + description: + It is a 6 bit value that specifies bias-ctrl-value. It is a PHY + tuning parameter that may vary for different boards of same SOC. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 63 + default: 32 + + qcom,charge-ctrl-value: + description: + It is a 2 bit value that specifies charge-ctrl-value. It is a PHY + tuning parameter that may vary for different boards of same SOC. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 0 + + qcom,hstx-trim-value: + description: + It is a 4 bit value that specifies tuning for HSTX + output current. + Possible range is - 15mA to 24mA (stepsize of 600 uA). + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 15 + default: 3 + + qcom,preemphasis-level: + description: + It is a 2 bit value that specifies pre-emphasis level. + Possible range is 0 to 15% (stepsize of 5%). + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 2 + + qcom,preemphasis-width: + description: + It is a 1 bit value that specifies how long the HSTX + pre-emphasis (specified using qcom,preemphasis-level) must be in + effect. Duration could be half-bit of full-bit. + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 1 + default: 0 + + qcom,hsdisc-trim-value: + description: + It is a 2 bit value tuning parameter that control disconnect + threshold and may vary for different boards of same SOC. + $ref: /schemas/types.yaml#/definitions/uint32 + minimum: 0 + maximum: 3 + default: 0 + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + - vdd-supply + - vdda-pll-supply + - vdda-phy-dpdm-supply + - resets + +allOf: + - if: + not: + properties: + compatible: + contains: + const: qcom,qusb2-v2-phy + then: + properties: + qcom,imp-res-offset-value: false + qcom,bias-ctrl-value: false + qcom,charge-ctrl-value: false + qcom,hstx-trim-value: false + qcom,preemphasis-level: false + qcom,preemphasis-width: false + qcom,hsdisc-trim-value: false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-msm8996.h> + hsusb_phy: phy@7411000 { + compatible = "qcom,msm8996-qusb2-phy"; + reg = <0x7411000 0x180>; + #phy-cells = <0>; + + clocks = <&gcc GCC_USB_PHY_CFG_AHB2PHY_CLK>, + <&gcc GCC_RX1_USB2_CLKREF_CLK>; + clock-names = "cfg_ahb", "ref"; + + vdd-supply = <&pm8994_l28>; + vdda-pll-supply = <&pm8994_l12>; + vdda-phy-dpdm-supply = <&pm8994_l24>; + + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; + nvmem-cells = <&qusb2p_hstx_trim>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,sa8775p-dwmac-sgmii-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sa8775p-dwmac-sgmii-phy.yaml new file mode 100644 index 000000000..b9107759b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,sa8775p-dwmac-sgmii-phy.yaml @@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,sa8775p-dwmac-sgmii-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SerDes/SGMII ethernet PHY controller + +maintainers: + - Bartosz Golaszewski <bartosz.golaszewski@linaro.org> + +description: + The SerDes PHY sits between the MAC and the external PHY and provides + separate Rx Tx lines. + +properties: + compatible: + const: qcom,sa8775p-dwmac-sgmii-phy + + reg: + items: + - description: serdes + + clocks: + maxItems: 1 + + clock-names: + const: sgmi_ref + + phy-supply: + description: + Phandle to a regulator that provides power to the PHY. + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,sa8775p-gcc.h> + serdes_phy: phy@8901000 { + compatible = "qcom,sa8775p-dwmac-sgmii-phy"; + reg = <0x08901000 0xe10>; + clocks = <&gcc GCC_SGMI_CLKREF_EN>; + clock-names = "sgmi_ref"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml new file mode 100644 index 000000000..2c3d6553a --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-pcie-phy.yaml @@ -0,0 +1,263 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QMP PHY controller (PCIe, SC8280XP) + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +description: + The QMP PHY controller supports physical layer functionality for a number of + controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB. + +properties: + compatible: + enum: + - qcom,sa8775p-qmp-gen4x2-pcie-phy + - qcom,sa8775p-qmp-gen4x4-pcie-phy + - qcom,sc8180x-qmp-pcie-phy + - qcom,sc8280xp-qmp-gen3x1-pcie-phy + - qcom,sc8280xp-qmp-gen3x2-pcie-phy + - qcom,sc8280xp-qmp-gen3x4-pcie-phy + - qcom,sdm845-qhp-pcie-phy + - qcom,sdm845-qmp-pcie-phy + - qcom,sdx55-qmp-pcie-phy + - qcom,sdx65-qmp-gen4x2-pcie-phy + - qcom,sm8150-qmp-gen3x1-pcie-phy + - qcom,sm8150-qmp-gen3x2-pcie-phy + - qcom,sm8250-qmp-gen3x1-pcie-phy + - qcom,sm8250-qmp-gen3x2-pcie-phy + - qcom,sm8250-qmp-modem-pcie-phy + - qcom,sm8350-qmp-gen3x1-pcie-phy + - qcom,sm8450-qmp-gen3x1-pcie-phy + - qcom,sm8450-qmp-gen4x2-pcie-phy + - qcom,sm8550-qmp-gen3x2-pcie-phy + - qcom,sm8550-qmp-gen4x2-pcie-phy + + reg: + minItems: 1 + maxItems: 2 + + clocks: + minItems: 5 + maxItems: 7 + + clock-names: + minItems: 5 + items: + - const: aux + - const: cfg_ahb + - const: ref + - enum: [rchng, refgen] + - const: pipe + - const: pipediv2 + - const: phy_aux + + power-domains: + maxItems: 1 + + resets: + minItems: 1 + maxItems: 2 + + reset-names: + minItems: 1 + items: + - const: phy + - const: phy_nocsr + + vdda-phy-supply: true + + vdda-pll-supply: true + + vdda-qref-supply: true + + qcom,4ln-config-sel: + description: PCIe 4-lane configuration + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle of TCSR syscon + - description: offset of PCIe 4-lane configuration register + - description: offset of configuration bit for this PHY + + "#clock-cells": + const: 0 + + clock-output-names: + maxItems: 1 + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - vdda-phy-supply + - vdda-pll-supply + - "#clock-cells" + - clock-output-names + - "#phy-cells" + +additionalProperties: false + +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,sc8280xp-qmp-gen3x4-pcie-phy + then: + properties: + reg: + items: + - description: port a + - description: port b + required: + - qcom,4ln-config-sel + else: + properties: + reg: + maxItems: 1 + + - if: + properties: + compatible: + contains: + enum: + - qcom,sc8180x-qmp-pcie-phy + - qcom,sdm845-qhp-pcie-phy + - qcom,sdm845-qmp-pcie-phy + - qcom,sdx55-qmp-pcie-phy + - qcom,sm8150-qmp-gen3x1-pcie-phy + - qcom,sm8150-qmp-gen3x2-pcie-phy + - qcom,sm8250-qmp-gen3x1-pcie-phy + - qcom,sm8250-qmp-gen3x2-pcie-phy + - qcom,sm8250-qmp-modem-pcie-phy + - qcom,sm8350-qmp-gen3x1-pcie-phy + - qcom,sm8450-qmp-gen3x1-pcie-phy + - qcom,sm8450-qmp-gen3x2-pcie-phy + - qcom,sm8550-qmp-gen3x2-pcie-phy + - qcom,sm8550-qmp-gen4x2-pcie-phy + then: + properties: + clocks: + maxItems: 5 + clock-names: + maxItems: 5 + + - if: + properties: + compatible: + contains: + enum: + - qcom,sc8280xp-qmp-gen3x1-pcie-phy + - qcom,sc8280xp-qmp-gen3x2-pcie-phy + - qcom,sc8280xp-qmp-gen3x4-pcie-phy + then: + properties: + clocks: + minItems: 6 + clock-names: + minItems: 6 + + - if: + properties: + compatible: + contains: + enum: + - qcom,sa8775p-qmp-gen4x2-pcie-phy + - qcom,sa8775p-qmp-gen4x4-pcie-phy + then: + properties: + clocks: + minItems: 7 + clock-names: + minItems: 7 + + - if: + properties: + compatible: + contains: + enum: + - qcom,sm8550-qmp-gen4x2-pcie-phy + then: + properties: + resets: + minItems: 2 + reset-names: + minItems: 2 + else: + properties: + resets: + maxItems: 1 + reset-names: + maxItems: 1 + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-sc8280xp.h> + + pcie2b_phy: phy@1c18000 { + compatible = "qcom,sc8280xp-qmp-gen3x2-pcie-phy"; + reg = <0x01c18000 0x2000>; + + clocks = <&gcc GCC_PCIE_2B_AUX_CLK>, + <&gcc GCC_PCIE_2B_CFG_AHB_CLK>, + <&gcc GCC_PCIE_2A2B_CLKREF_CLK>, + <&gcc GCC_PCIE2B_PHY_RCHNG_CLK>, + <&gcc GCC_PCIE_2B_PIPE_CLK>, + <&gcc GCC_PCIE_2B_PIPEDIV2_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "rchng", + "pipe", "pipediv2"; + + power-domains = <&gcc PCIE_2B_GDSC>; + + resets = <&gcc GCC_PCIE_2B_PHY_BCR>; + reset-names = "phy"; + + vdda-phy-supply = <&vreg_l6d>; + vdda-pll-supply = <&vreg_l4d>; + + #clock-cells = <0>; + clock-output-names = "pcie_2b_pipe_clk"; + + #phy-cells = <0>; + }; + + pcie2a_phy: phy@1c24000 { + compatible = "qcom,sc8280xp-qmp-gen3x4-pcie-phy"; + reg = <0x01c24000 0x2000>, <0x01c26000 0x2000>; + + clocks = <&gcc GCC_PCIE_2A_AUX_CLK>, + <&gcc GCC_PCIE_2A_CFG_AHB_CLK>, + <&gcc GCC_PCIE_2A2B_CLKREF_CLK>, + <&gcc GCC_PCIE2A_PHY_RCHNG_CLK>, + <&gcc GCC_PCIE_2A_PIPE_CLK>, + <&gcc GCC_PCIE_2A_PIPEDIV2_CLK>; + clock-names = "aux", "cfg_ahb", "ref", "rchng", + "pipe", "pipediv2"; + + power-domains = <&gcc PCIE_2A_GDSC>; + + resets = <&gcc GCC_PCIE_2A_PHY_BCR>; + reset-names = "phy"; + + vdda-phy-supply = <&vreg_l6d>; + vdda-pll-supply = <&vreg_l4d>; + + qcom,4ln-config-sel = <&tcsr 0xa044 0>; + + #clock-cells = <0>; + clock-output-names = "pcie_2a_pipe_clk"; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml new file mode 100644 index 000000000..d981d77e8 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-ufs-phy.yaml @@ -0,0 +1,155 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-ufs-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QMP PHY controller (UFS, SC8280XP) + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +description: + The QMP PHY controller supports physical layer functionality for a number of + controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB. + +properties: + compatible: + enum: + - qcom,msm8996-qmp-ufs-phy + - qcom,msm8998-qmp-ufs-phy + - qcom,sa8775p-qmp-ufs-phy + - qcom,sc8180x-qmp-ufs-phy + - qcom,sc8280xp-qmp-ufs-phy + - qcom,sdm845-qmp-ufs-phy + - qcom,sm6115-qmp-ufs-phy + - qcom,sm6125-qmp-ufs-phy + - qcom,sm6350-qmp-ufs-phy + - qcom,sm7150-qmp-ufs-phy + - qcom,sm8150-qmp-ufs-phy + - qcom,sm8250-qmp-ufs-phy + - qcom,sm8350-qmp-ufs-phy + - qcom,sm8450-qmp-ufs-phy + - qcom,sm8550-qmp-ufs-phy + + reg: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 3 + + clock-names: + minItems: 1 + items: + - const: ref + - const: ref_aux + - const: qref + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + reset-names: + items: + - const: ufsphy + + vdda-phy-supply: true + + vdda-pll-supply: true + + "#clock-cells": + const: 1 + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - clocks + - clock-names + - power-domains + - resets + - reset-names + - vdda-phy-supply + - vdda-pll-supply + - "#phy-cells" + +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,sa8775p-qmp-ufs-phy + - qcom,sm8450-qmp-ufs-phy + then: + properties: + clocks: + minItems: 3 + clock-names: + minItems: 3 + + - if: + properties: + compatible: + contains: + enum: + - qcom,msm8998-qmp-ufs-phy + - qcom,sc8180x-qmp-ufs-phy + - qcom,sc8280xp-qmp-ufs-phy + - qcom,sdm845-qmp-ufs-phy + - qcom,sm6115-qmp-ufs-phy + - qcom,sm6125-qmp-ufs-phy + - qcom,sm6350-qmp-ufs-phy + - qcom,sm7150-qmp-ufs-phy + - qcom,sm8150-qmp-ufs-phy + - qcom,sm8250-qmp-ufs-phy + - qcom,sm8350-qmp-ufs-phy + - qcom,sm8550-qmp-ufs-phy + then: + properties: + clocks: + maxItems: 2 + clock-names: + maxItems: 2 + + - if: + properties: + compatible: + contains: + enum: + - qcom,msm8996-qmp-ufs-phy + then: + properties: + clocks: + maxItems: 1 + clock-names: + maxItems: 1 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-sc8280xp.h> + + ufs_mem_phy: phy@1d87000 { + compatible = "qcom,sc8280xp-qmp-ufs-phy"; + reg = <0x01d87000 0x1000>; + + clocks = <&gcc GCC_UFS_REF_CLKREF_CLK>, <&gcc GCC_UFS_PHY_PHY_AUX_CLK>; + clock-names = "ref", "ref_aux"; + + power-domains = <&gcc UFS_PHY_GDSC>; + + resets = <&ufs_mem_hc 0>; + reset-names = "ufsphy"; + + vdda-phy-supply = <&vreg_l6b>; + vdda-pll-supply = <&vreg_l3b>; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml new file mode 100644 index 000000000..f99fbbcd6 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml @@ -0,0 +1,155 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb3-uni-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QMP PHY controller (USB, SC8280XP) + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +description: + The QMP PHY controller supports physical layer functionality for a number of + controllers on Qualcomm chipsets, such as, PCIe, UFS, and USB. + +properties: + compatible: + enum: + - qcom,ipq9574-qmp-usb3-phy + - qcom,qcm2290-qmp-usb3-phy + - qcom,sa8775p-qmp-usb3-uni-phy + - qcom,sc8280xp-qmp-usb3-uni-phy + - qcom,sm6115-qmp-usb3-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 4 + + clock-names: + maxItems: 4 + + power-domains: + maxItems: 1 + + resets: + maxItems: 2 + + reset-names: + items: + - const: phy + - const: phy_phy + + vdda-phy-supply: true + + vdda-pll-supply: true + + "#clock-cells": + const: 0 + + clock-output-names: + maxItems: 1 + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - vdda-phy-supply + - vdda-pll-supply + - "#clock-cells" + - clock-output-names + - "#phy-cells" + +allOf: + - if: + properties: + compatible: + contains: + enum: + - qcom,ipq9574-qmp-usb3-phy + then: + properties: + clock-names: + items: + - const: aux + - const: ref + - const: cfg_ahb + - const: pipe + + - if: + properties: + compatible: + contains: + enum: + - qcom,qcm2290-qmp-usb3-phy + - qcom,sm6115-qmp-usb3-phy + then: + properties: + clocks: + maxItems: 4 + clock-names: + items: + - const: cfg_ahb + - const: ref + - const: com_aux + - const: pipe + + - if: + properties: + compatible: + contains: + enum: + - qcom,sa8775p-qmp-usb3-uni-phy + - qcom,sc8280xp-qmp-usb3-uni-phy + then: + properties: + clocks: + maxItems: 4 + clock-names: + items: + - const: aux + - const: ref + - const: com_aux + - const: pipe + required: + - power-domains + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-sc8280xp.h> + #include <dt-bindings/clock/qcom,rpmh.h> + + phy@88ef000 { + compatible = "qcom,sc8280xp-qmp-usb3-uni-phy"; + reg = <0x088ef000 0x2000>; + + clocks = <&gcc GCC_USB3_MP_PHY_AUX_CLK>, + <&gcc GCC_USB3_MP0_CLKREF_CLK>, + <&gcc GCC_USB3_MP_PHY_COM_AUX_CLK>, + <&gcc GCC_USB3_MP_PHY_PIPE_0_CLK>; + clock-names = "aux", "ref", "com_aux", "pipe"; + + power-domains = <&gcc USB30_MP_GDSC>; + + resets = <&gcc GCC_USB3_UNIPHY_MP0_BCR>, + <&gcc GCC_USB3UNIPHY_PHY_MP0_BCR>; + reset-names = "phy", "phy_phy"; + + vdda-phy-supply = <&vreg_l3a>; + vdda-pll-supply = <&vreg_l5a>; + + #clock-cells = <0>; + clock-output-names = "usb2_phy0_pipe_clk"; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml new file mode 100644 index 000000000..fa7408eb7 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml @@ -0,0 +1,196 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,sc8280xp-qmp-usb43dp-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm QMP USB4-USB3-DP PHY controller (SC8280XP) + +maintainers: + - Vinod Koul <vkoul@kernel.org> + +description: + The QMP PHY controller supports physical layer functionality for a number of + controllers on Qualcomm chipsets, such as, PCIe, UFS and USB. + +properties: + compatible: + enum: + - qcom,sc7180-qmp-usb3-dp-phy + - qcom,sc7280-qmp-usb3-dp-phy + - qcom,sc8180x-qmp-usb3-dp-phy + - qcom,sc8280xp-qmp-usb43dp-phy + - qcom,sdm845-qmp-usb3-dp-phy + - qcom,sm6350-qmp-usb3-dp-phy + - qcom,sm8150-qmp-usb3-dp-phy + - qcom,sm8250-qmp-usb3-dp-phy + - qcom,sm8350-qmp-usb3-dp-phy + - qcom,sm8450-qmp-usb3-dp-phy + - qcom,sm8550-qmp-usb3-dp-phy + + reg: + maxItems: 1 + + clocks: + minItems: 4 + maxItems: 5 + + clock-names: + minItems: 4 + items: + - const: aux + - const: ref + - const: com_aux + - const: usb3_pipe + - const: cfg_ahb + + power-domains: + maxItems: 1 + + resets: + maxItems: 2 + + reset-names: + items: + - const: phy + - const: common + + vdda-phy-supply: true + + vdda-pll-supply: true + + "#clock-cells": + const: 1 + description: + See include/dt-bindings/phy/phy-qcom-qmp.h + + "#phy-cells": + const: 1 + description: + See include/dt-bindings/phy/phy-qcom-qmp.h + + orientation-switch: + description: + Flag the PHY as possible handler of USB Type-C orientation switching + type: boolean + + ports: + $ref: /schemas/graph.yaml#/properties/ports + properties: + port@0: + $ref: /schemas/graph.yaml#/properties/port + description: Output endpoint of the PHY + + port@1: + $ref: /schemas/graph.yaml#/properties/port + description: Incoming endpoint from the USB controller + + port@2: + $ref: /schemas/graph.yaml#/properties/port + description: Incoming endpoint from the DisplayPort controller + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + - vdda-phy-supply + - vdda-pll-supply + - "#clock-cells" + - "#phy-cells" + +allOf: + - if: + properties: + compatible: + enum: + - qcom,sc7180-qmp-usb3-dp-phy + - qcom,sdm845-qmp-usb3-dp-phy + then: + properties: + clocks: + maxItems: 5 + clock-names: + maxItems: 5 + else: + properties: + clocks: + maxItems: 4 + clock-names: + maxItems: 4 + + - if: + properties: + compatible: + enum: + - qcom,sc8280xp-qmp-usb43dp-phy + - qcom,sm6350-qmp-usb3-dp-phy + - qcom,sm8550-qmp-usb3-dp-phy + then: + required: + - power-domains + else: + properties: + power-domains: false + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-sc8280xp.h> + + phy@88eb000 { + compatible = "qcom,sc8280xp-qmp-usb43dp-phy"; + reg = <0x088eb000 0x4000>; + + clocks = <&gcc GCC_USB3_PRIM_PHY_AUX_CLK>, + <&gcc GCC_USB4_EUD_CLKREF_CLK>, + <&gcc GCC_USB3_PRIM_PHY_COM_AUX_CLK>, + <&gcc GCC_USB3_PRIM_PHY_PIPE_CLK>; + clock-names = "aux", "ref", "com_aux", "usb3_pipe"; + + power-domains = <&gcc USB30_PRIM_GDSC>; + + resets = <&gcc GCC_USB3_PHY_PRIM_BCR>, + <&gcc GCC_USB4_DP_PHY_PRIM_BCR>; + reset-names = "phy", "common"; + + vdda-phy-supply = <&vreg_l9d>; + vdda-pll-supply = <&vreg_l4d>; + + orientation-switch; + + #clock-cells = <1>; + #phy-cells = <1>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + endpoint { + remote-endpoint = <&typec_connector_ss>; + }; + }; + + port@1 { + reg = <1>; + + endpoint { + remote-endpoint = <&dwc3_ss_out>; + }; + }; + + port@2 { + reg = <2>; + + endpoint { + remote-endpoint = <&mdss_dp_out>; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml new file mode 100644 index 000000000..c53bab107 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-phy.yaml @@ -0,0 +1,79 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,snps-eusb2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm SNPS eUSB2 phy controller + +maintainers: + - Abel Vesa <abel.vesa@linaro.org> + +description: + eUSB2 controller supports LS/FS/HS usb connectivity on Qualcomm chipsets. + +properties: + compatible: + const: qcom,sm8550-snps-eusb2-phy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + items: + - description: ref + + clock-names: + items: + - const: ref + + resets: + maxItems: 1 + + phys: + maxItems: 1 + description: + Phandle to eUSB2 to USB 2.0 repeater + + vdd-supply: + description: + Phandle to 0.88V regulator supply to PHY digital circuit. + + vdda12-supply: + description: + Phandle to 1.2V regulator supply to PHY refclk pll block. + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + - vdd-supply + - vdda12-supply + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,sm8550-gcc.h> + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/clock/qcom,sm8550-tcsr.h> + + usb_1_hsphy: phy@88e3000 { + compatible = "qcom,sm8550-snps-eusb2-phy"; + reg = <0x88e3000 0x154>; + #phy-cells = <0>; + + clocks = <&tcsrcc TCSR_USB2_CLKREF_EN>; + clock-names = "ref"; + + vdd-supply = <&vreg_l1e_0p88>; + vdda12-supply = <&vreg_l3e_1p2>; + + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-repeater.yaml b/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-repeater.yaml new file mode 100644 index 000000000..24c733c10 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,snps-eusb2-repeater.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,snps-eusb2-repeater.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Synopsis eUSB2 to USB 2.0 repeater + +maintainers: + - Abel Vesa <abel.vesa@linaro.org> + +description: + eUSB2 repeater converts between eUSB2 and USB 2.0 signaling levels and + allows a eUSB2 PHY to connect to legacy USB 2.0 products + +properties: + compatible: + oneOf: + - items: + - enum: + - qcom,pm7550ba-eusb2-repeater + - const: qcom,pm8550b-eusb2-repeater + - const: qcom,pm8550b-eusb2-repeater + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + vdd18-supply: true + + vdd3-supply: true + + qcom,tune-usb2-disc-thres: + $ref: /schemas/types.yaml#/definitions/uint8 + description: High-Speed disconnect threshold + minimum: 0 + maximum: 7 + default: 0 + + qcom,tune-usb2-amplitude: + $ref: /schemas/types.yaml#/definitions/uint8 + description: High-Speed trasmit amplitude + minimum: 0 + maximum: 15 + default: 8 + + qcom,tune-usb2-preem: + $ref: /schemas/types.yaml#/definitions/uint8 + description: High-Speed TX pre-emphasis tuning + minimum: 0 + maximum: 7 + default: 5 + +required: + - compatible + - reg + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/spmi/spmi.h> + + pmic@7 { + reg = <0x7 SPMI_USID>; + #address-cells = <1>; + #size-cells = <0>; + + pm8550b_eusb2_repeater: phy@fd00 { + compatible = "qcom,pm8550b-eusb2-repeater"; + reg = <0xfd00>; + #phy-cells = <0>; + }; + }; +... diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt new file mode 100644 index 000000000..2cb2168ce --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,usb-8x16-phy.txt @@ -0,0 +1,76 @@ +Qualcomm's APQ8016/MSM8916 USB transceiver controller + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,usb-8x16-phy". + +- reg: + Usage: required + Value type: <prop-encoded-array> + Definition: USB PHY base address and length of the register map + +- clocks: + Usage: required + Value type: <prop-encoded-array> + Definition: See clock-bindings.txt section "consumers". List of + two clock specifiers for interface and core controller + clocks. + +- clock-names: + Usage: required + Value type: <string> + Definition: Must contain "iface" and "core" strings. + +- vddcx-supply: + Usage: required + Value type: <phandle> + Definition: phandle to the regulator VDCCX supply node. + +- v1p8-supply: + Usage: required + Value type: <phandle> + Definition: phandle to the regulator 1.8V supply node. + +- v3p3-supply: + Usage: required + Value type: <phandle> + Definition: phandle to the regulator 3.3V supply node. + +- resets: + Usage: required + Value type: <prop-encoded-array> + Definition: See reset.txt section "consumers". PHY reset specifier. + +- reset-names: + Usage: required + Value type: <string> + Definition: Must contain "phy" string. + +- switch-gpio: + Usage: optional + Value type: <prop-encoded-array> + Definition: Some boards are using Dual SPDT USB Switch, witch is + controlled by GPIO to de/multiplex D+/D- USB lines + between connectors. + +Example: + usb_phy: phy@78d9000 { + compatible = "qcom,usb-8x16-phy"; + reg = <0x78d9000 0x400>; + + vddcx-supply = <&pm8916_s1_corner>; + v1p8-supply = <&pm8916_l7>; + v3p3-supply = <&pm8916_l13>; + + clocks = <&gcc GCC_USB_HS_AHB_CLK>, + <&gcc GCC_USB_HS_SYSTEM_CLK>; + clock-names = "iface", "core"; + + resets = <&gcc GCC_USB2A_PHY_BCR>; + reset-names = "phy"; + + // D+/D- lines: 1 - Routed to HUB, 0 - Device connector + switch-gpio = <&pm8916_gpios 4 GPIO_ACTIVE_HIGH>; + }; + diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml new file mode 100644 index 000000000..6c99e02b2 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-28nm.yaml @@ -0,0 +1,90 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,usb-hs-28nm.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Synopsys DesignWare Core 28nm High-Speed PHY + +maintainers: + - Bryan O'Donoghue <bryan.odonoghue@linaro.org> + +description: | + Qualcomm Low-Speed, Full-Speed, Hi-Speed 28nm USB PHY + +properties: + compatible: + enum: + - qcom,usb-hs-28nm-femtophy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + items: + - description: rpmcc ref clock + - description: PHY AHB clock + - description: Rentention clock + + clock-names: + items: + - const: ref + - const: ahb + - const: sleep + + resets: + items: + - description: PHY core reset + - description: POR reset + + reset-names: + items: + - const: phy + - const: por + + vdd-supply: + description: phandle to the regulator VDD supply node. + + vdda1p8-supply: + description: phandle to the regulator 1.8V supply node. + + vdda3p3-supply: + description: phandle to the regulator 3.3V supply node. + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + - resets + - reset-names + - vdd-supply + - vdda1p8-supply + - vdda3p3-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-qcs404.h> + #include <dt-bindings/clock/qcom,rpmcc.h> + usb2_phy_prim: phy@7a000 { + compatible = "qcom,usb-hs-28nm-femtophy"; + reg = <0x0007a000 0x200>; + #phy-cells = <0>; + clocks = <&rpmcc RPM_SMD_LN_BB_CLK>, + <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>, + <&gcc GCC_USB2A_PHY_SLEEP_CLK>; + clock-names = "ref", "ahb", "sleep"; + resets = <&gcc GCC_USB_HS_PHY_CFG_AHB_BCR>, + <&gcc GCC_USB2A_PHY_BCR>; + reset-names = "phy", "por"; + vdd-supply = <&vreg_l4_1p2>; + vdda1p8-supply = <&vreg_l5_1p8>; + vdda3p3-supply = <&vreg_l12_3p3>; + }; +... diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml new file mode 100644 index 000000000..f042d6af1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.yaml @@ -0,0 +1,114 @@ +# SPDX-License-Identifier: GPL-2.0-only +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,usb-hs-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm's USB HS PHY + +maintainers: + - Bjorn Andersson <bjorn.andersson@linaro.org> + +if: + properties: + compatible: + contains: + enum: + - qcom,usb-hs-phy-apq8064 + - qcom,usb-hs-phy-msm8960 +then: + properties: + resets: + maxItems: 1 + + reset-names: + const: por + +else: + properties: + resets: + minItems: 2 + maxItems: 2 + + reset-names: + items: + - const: phy + - const: por + +properties: + compatible: + items: + - enum: + - qcom,usb-hs-phy-apq8064 + - qcom,usb-hs-phy-msm8226 + - qcom,usb-hs-phy-msm8916 + - qcom,usb-hs-phy-msm8960 + - qcom,usb-hs-phy-msm8974 + - const: qcom,usb-hs-phy + + clocks: + minItems: 2 + maxItems: 2 + + clock-names: + maxItems: 2 + contains: + items: + - const: ref + - const: sleep + + resets: true + + reset-names: true + + v1p8-supply: true + + v3p3-supply: true + + extcon: true + + "#phy-cells": + const: 0 + + qcom,init-seq: + $ref: /schemas/types.yaml#/definitions/uint8-matrix + description: > + Sequence of ULPI address and value pairs to + program into the ULPI_EXT_VENDOR_SPECIFIC area. + This is related to Device Mode Eye Diagram test. + maxItems: 32 # no hard limit + items: + items: + - description: > + the address is offset from the ULPI_EXT_VENDOR_SPECIFIC address + - description: value + +required: + - clocks + - clock-names + - resets + - reset-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + otg: usb-controller { + #reset-cells = <1>; + + ulpi { + phy { + compatible = "qcom,usb-hs-phy-msm8974", "qcom,usb-hs-phy"; + #phy-cells = <0>; + clocks = <&clk 0>, <&clk 258>; + clock-names = "ref", "sleep"; + resets = <&gcc 10>, <&otg 0>; + reset-names = "phy", "por"; + v3p3-supply = <&pm8941_l24>; + v1p8-supply = <&pm8941_l6>; + extcon = <&smbb>; + qcom,init-seq = /bits/ 8 <0x1 0x63>; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.yaml new file mode 100644 index 000000000..077e13a94 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.yaml @@ -0,0 +1,67 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,usb-hsic-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm USB HSIC PHY Controller + +maintainers: + - Bjorn Andersson <andersson@kernel.org> + - Vinod Koul <vkoul@kernel.org> + +properties: + compatible: + items: + - enum: + - qcom,usb-hsic-phy-mdm9615 + - qcom,usb-hsic-phy-msm8974 + - const: qcom,usb-hsic-phy + + clocks: + maxItems: 3 + + clock-names: + items: + - const: phy + - const: cal + - const: cal_sleep + + "#phy-cells": + const: 0 + + pinctrl-0: true + pinctrl-1: true + + pinctrl-names: + items: + - const: init + - const: default + +required: + - compatible + - clocks + - clock-names + - "#phy-cells" + - pinctrl-0 + - pinctrl-1 + - pinctrl-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-msm8974.h> + + phy { + compatible = "qcom,usb-hsic-phy-msm8974", + "qcom,usb-hsic-phy"; + clocks = <&gcc GCC_USB_HSIC_CLK>, + <&gcc GCC_USB_HSIC_IO_CAL_CLK>, + <&gcc GCC_USB_HSIC_IO_CAL_SLEEP_CLK>; + clock-names = "phy", "cal", "cal_sleep"; + #phy-cells = <0>; + pinctrl-names = "init", "default"; + pinctrl-0 = <&hsic_sleep>; + pinctrl-1 = <&hsic_default>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml new file mode 100644 index 000000000..0f200e3f9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,usb-snps-femto-v2.yaml @@ -0,0 +1,184 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,usb-snps-femto-v2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Synopsys Femto High-Speed USB PHY V2 + +maintainers: + - Wesley Cheng <quic_wcheng@quicinc.com> + +description: | + Qualcomm High-Speed USB PHY + +properties: + compatible: + oneOf: + - enum: + - qcom,sc8180x-usb-hs-phy + - qcom,usb-snps-femto-v2-phy + - items: + - enum: + - qcom,sa8775p-usb-hs-phy + - qcom,sc8280xp-usb-hs-phy + - const: qcom,usb-snps-hs-5nm-phy + - items: + - enum: + - qcom,sc7280-usb-hs-phy + - qcom,sdx55-usb-hs-phy + - qcom,sdx65-usb-hs-phy + - qcom,sm6375-usb-hs-phy + - qcom,sm8150-usb-hs-phy + - qcom,sm8250-usb-hs-phy + - qcom,sm8350-usb-hs-phy + - qcom,sm8450-usb-hs-phy + - const: qcom,usb-snps-hs-7nm-phy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + items: + - description: rpmhcc ref clock + + clock-names: + items: + - const: ref + + resets: + items: + - description: PHY core reset + + vdda-pll-supply: + description: phandle to the regulator VDD supply node. + + vdda18-supply: + description: phandle to the regulator 1.8V supply node. + + vdda33-supply: + description: phandle to the regulator 3.3V supply node. + + qcom,hs-disconnect-bp: + description: + This adjusts the voltage level for the threshold used to + detect a disconnect event at the host. + The hardware accepts only discrete values. The value closest to the + provided input will be chosen as the override value for this param. + minimum: -272 + maximum: 2156 + + qcom,squelch-detector-bp: + description: + This adjusts the voltage level for the threshold used to + detect valid high-speed data. + The hardware accepts only discrete values. The value closest to the + provided input will be chosen as the override value for this param. + minimum: -2090 + maximum: 1590 + + qcom,hs-amplitude-bp: + description: + This adjusts the high-speed DC level voltage. + The hardware accepts only discrete values. The value closest to the + provided input will be chosen as the override value for this param. + minimum: -660 + maximum: 2670 + + qcom,pre-emphasis-duration-bp: + description: + This signal controls the duration for which the + HS pre-emphasis current is sourced onto DP<#> or DM<#>. + The HS Transmitter pre-emphasis duration is defined in terms of + unit amounts. One unit of pre-emphasis duration is approximately + 650 ps and is defined as 1X pre-emphasis duration. + The hardware accepts only discrete values. The value closest to the + provided input will be chosen as the override value for this param. + minimum: 10000 + maximum: 20000 + + qcom,pre-emphasis-amplitude-bp: + description: + This signal controls the amount of current sourced to + DP<#> and DM<#> after a J-to-K or K-to-J transition. + The HS Transmitter pre-emphasis current is defined in terms of unit + amounts. One unit amount is approximately 2 mA and is defined as + 1X pre-emphasis current. + The hardware accepts only discrete values. The value closest to the + provided input will be chosen as the override value for this param. + minimum: 10000 + maximum: 40000 + + qcom,hs-rise-fall-time-bp: + description: + This adjusts the rise/fall times of the high-speed waveform. + The hardware accepts only discrete values. The value closest to the + provided input will be chosen as the override value for this param. + minimum: -4100 + maximum: 5430 + + qcom,hs-crossover-voltage-microvolt: + description: + This adjusts the voltage at which the DP<#> and DM<#> + signals cross while transmitting in HS mode. + The hardware accepts only discrete values. The value closest to the + provided input will be chosen as the override value for this param. + minimum: -31000 + maximum: 28000 + + qcom,hs-output-impedance-micro-ohms: + description: + In some applications, there can be significant series resistance + on the D+ and D- paths between the transceiver and cable. This adjusts + the driver source impedance to compensate for added series + resistance on the USB. The hardware accepts only discrete values. The + value closest to the provided input will be chosen as the override value + for this param. + minimum: -2300000 + maximum: 6100000 + + qcom,ls-fs-output-impedance-bp: + description: + This adjusts the low- and full-speed single-ended source + impedance while driving high. The following adjustment values are based + on nominal process, voltage, and temperature. + The hardware accepts only discrete values. The value closest to the + provided input will be chosen as the override value for this param. + minimum: -1053 + maximum: 1310 + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + - resets + - vdda-pll-supply + - vdda18-supply + - vdda33-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,rpmh.h> + #include <dt-bindings/clock/qcom,gcc-sm8150.h> + phy@88e2000 { + compatible = "qcom,sm8150-usb-hs-phy", "qcom,usb-snps-hs-7nm-phy"; + reg = <0x088e2000 0x400>; + #phy-cells = <0>; + + clocks = <&rpmhcc RPMH_CXO_CLK>; + clock-names = "ref"; + + resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; + + vdda-pll-supply = <&vdd_usb_hs_core>; + vdda33-supply = <&vdda_usb_hs_3p1>; + vdda18-supply = <&vdda_usb_hs_1p8>; + }; +... diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml b/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml new file mode 100644 index 000000000..6e4254ff1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom,usb-ss.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom,usb-ss.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcomm Synopsys 1.0.0 SuperSpeed USB PHY + +maintainers: + - Bryan O'Donoghue <bryan.odonoghue@linaro.org> + +description: | + Qualcomm Synopsys 1.0.0 SuperSpeed USB PHY + +properties: + compatible: + enum: + - qcom,usb-ss-28nm-phy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + items: + - description: rpmcc clock + - description: PHY AHB clock + - description: SuperSpeed pipe clock + + clock-names: + items: + - const: ref + - const: ahb + - const: pipe + + vdd-supply: + description: phandle to the regulator VDD supply node. + + vdda1p8-supply: + description: phandle to the regulator 1.8V supply node. + + resets: + items: + - description: COM reset + - description: PHY reset line + + reset-names: + items: + - const: com + - const: phy + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + - vdd-supply + - vdda1p8-supply + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-qcs404.h> + #include <dt-bindings/clock/qcom,rpmcc.h> + usb3_phy: usb3-phy@78000 { + compatible = "qcom,usb-ss-28nm-phy"; + reg = <0x78000 0x400>; + #phy-cells = <0>; + clocks = <&rpmcc RPM_SMD_LN_BB_CLK>, + <&gcc GCC_USB_HS_PHY_CFG_AHB_CLK>, + <&gcc GCC_USB3_PHY_PIPE_CLK>; + clock-names = "ref", "ahb", "pipe"; + resets = <&gcc GCC_USB3_PHY_BCR>, + <&gcc GCC_USB3PHY_PHY_BCR>; + reset-names = "com", "phy"; + vdd-supply = <&vreg_l3_1p05>; + vdda1p8-supply = <&vreg_l5_1p8>; + }; +... diff --git a/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt b/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt new file mode 100644 index 000000000..952f6c96b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-apq8064-sata-phy.txt @@ -0,0 +1,24 @@ +Qualcomm APQ8064 SATA PHY Controller +------------------------------------ + +SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. +Each SATA PHY controller should have its own node. + +Required properties: +- compatible: compatible list, contains "qcom,apq8064-sata-phy". +- reg: offset and length of the SATA PHY register set; +- #phy-cells: must be zero +- clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. +- clock-names: must be "cfg" for phy config clock. + +Example: + sata_phy: sata-phy@1b400000 { + compatible = "qcom,apq8064-sata-phy"; + reg = <0x1b400000 0x200>; + + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt b/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt new file mode 100644 index 000000000..76bfbd056 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-ipq806x-sata-phy.txt @@ -0,0 +1,23 @@ +Qualcomm IPQ806x SATA PHY Controller +------------------------------------ + +SATA PHY nodes are defined to describe on-chip SATA Physical layer controllers. +Each SATA PHY controller should have its own node. + +Required properties: +- compatible: compatible list, contains "qcom,ipq806x-sata-phy" +- reg: offset and length of the SATA PHY register set; +- #phy-cells: must be zero +- clocks: must be exactly one entry +- clock-names: must be "cfg" + +Example: + sata_phy: sata-phy@1b400000 { + compatible = "qcom,ipq806x-sata-phy"; + reg = <0x1b400000 0x200>; + + clocks = <&gcc SATA_PHY_CFG_CLK>; + clock-names = "cfg"; + + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.yaml b/Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.yaml new file mode 100644 index 000000000..09c614952 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/qcom-usb-ipq4019-phy.yaml @@ -0,0 +1,52 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/qcom-usb-ipq4019-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Qualcom IPQ40xx Dakota HS/SS USB PHY + +maintainers: + - Robert Marko <robert.marko@sartura.hr> + +properties: + compatible: + enum: + - qcom,usb-ss-ipq4019-phy + - qcom,usb-hs-ipq4019-phy + + reg: + maxItems: 1 + + resets: + maxItems: 2 + + reset-names: + items: + - const: por_rst + - const: srif_rst + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - resets + - reset-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/qcom,gcc-ipq4019.h> + + hsphy@a8000 { + #phy-cells = <0>; + compatible = "qcom,usb-hs-ipq4019-phy"; + reg = <0xa8000 0x40>; + resets = <&gcc USB2_HSPHY_POR_ARES>, + <&gcc USB2_HSPHY_S_ARES>; + reset-names = "por_rst", "srif_rst"; + }; diff --git a/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt b/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt new file mode 100644 index 000000000..9d2868a43 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/ralink-usb-phy.txt @@ -0,0 +1,23 @@ +Mediatek/Ralink USB PHY + +Required properties: + - compatible: "ralink,rt3352-usbphy" + "mediatek,mt7620-usbphy" + "mediatek,mt7628-usbphy" + - reg: required for "mediatek,mt7628-usbphy", unused otherwise + - #phy-cells: should be 0 + - ralink,sysctl: a phandle to a ralink syscon register region + - resets: the two reset controllers for host and device + - reset-names: the names of the 2 reset controllers + +Example: + +usbphy: phy { + compatible = "mediatek,mt7628-usbphy"; + reg = <0x10120000 0x1000>; + #phy-cells = <0>; + + ralink,sysctl = <&sysc>; + resets = <&rstctrl 22 &rstctrl 25>; + reset-names = "host", "device"; +}; diff --git a/Documentation/devicetree/bindings/phy/realtek,usb2phy.yaml b/Documentation/devicetree/bindings/phy/realtek,usb2phy.yaml new file mode 100644 index 000000000..9911ada39 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/realtek,usb2phy.yaml @@ -0,0 +1,175 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2023 Realtek Semiconductor Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/realtek,usb2phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Realtek DHC SoCs USB 2.0 PHY + +maintainers: + - Stanley Chang <stanley_chang@realtek.com> + +description: | + Realtek USB 2.0 PHY support the digital home center (DHC) RTD series SoCs. + The USB 2.0 PHY driver is designed to support the XHCI controller. The SoCs + support multiple XHCI controllers. One PHY device node maps to one XHCI + controller. + + RTD1295/RTD1619 SoCs USB + The USB architecture includes three XHCI controllers. + Each XHCI maps to one USB 2.0 PHY and map one USB 3.0 PHY on some + controllers. + XHCI controller#0 -- usb2phy -- phy#0 + |- usb3phy -- phy#0 + XHCI controller#1 -- usb2phy -- phy#0 + XHCI controller#2 -- usb2phy -- phy#0 + |- usb3phy -- phy#0 + + RTD1395 SoCs USB + The USB architecture includes two XHCI controllers. + The controller#0 has one USB 2.0 PHY. The controller#1 includes two USB 2.0 + PHY. + XHCI controller#0 -- usb2phy -- phy#0 + XHCI controller#1 -- usb2phy -- phy#0 + |- phy#1 + + RTD1319/RTD1619b SoCs USB + The USB architecture includes three XHCI controllers. + Each XHCI maps to one USB 2.0 PHY and map one USB 3.0 PHY on controllers#2. + XHCI controller#0 -- usb2phy -- phy#0 + XHCI controller#1 -- usb2phy -- phy#0 + XHCI controller#2 -- usb2phy -- phy#0 + |- usb3phy -- phy#0 + + RTD1319d SoCs USB + The USB architecture includes three XHCI controllers. + Each xhci maps to one USB 2.0 PHY and map one USB 3.0 PHY on controllers#0. + XHCI controller#0 -- usb2phy -- phy#0 + |- usb3phy -- phy#0 + XHCI controller#1 -- usb2phy -- phy#0 + XHCI controller#2 -- usb2phy -- phy#0 + + RTD1312c/RTD1315e SoCs USB + The USB architecture includes three XHCI controllers. + Each XHCI maps to one USB 2.0 PHY. + XHCI controller#0 -- usb2phy -- phy#0 + XHCI controller#1 -- usb2phy -- phy#0 + XHCI controller#2 -- usb2phy -- phy#0 + +properties: + compatible: + enum: + - realtek,rtd1295-usb2phy + - realtek,rtd1312c-usb2phy + - realtek,rtd1315e-usb2phy + - realtek,rtd1319-usb2phy + - realtek,rtd1319d-usb2phy + - realtek,rtd1395-usb2phy + - realtek,rtd1395-usb2phy-2port + - realtek,rtd1619-usb2phy + - realtek,rtd1619b-usb2phy + + reg: + items: + - description: PHY data registers + - description: PHY control registers + + "#phy-cells": + const: 0 + + nvmem-cells: + maxItems: 2 + description: + Phandles to nvmem cell that contains the trimming data. + If unspecified, default value is used. + + nvmem-cell-names: + items: + - const: usb-dc-cal + - const: usb-dc-dis + description: + The following names, which correspond to each nvmem-cells. + usb-dc-cal is the driving level for each phy specified via efuse. + usb-dc-dis is the disconnection level for each phy specified via efuse. + + realtek,inverse-hstx-sync-clock: + description: + For one of the phys of RTD1619b SoC, the synchronous clock of the + high-speed tx must be inverted. + type: boolean + + realtek,driving-level: + description: + Control the magnitude of High speed Dp/Dm output swing (mV). + For a different board or port, the original magnitude maybe not meet + the specification. In this situation we can adjust the value to meet + the specification. + $ref: /schemas/types.yaml#/definitions/uint32 + default: 8 + minimum: 0 + maximum: 31 + + realtek,driving-level-compensate: + description: + For RTD1315e SoC, the driving level can be adjusted by reading the + efuse table. This property provides drive compensation. + If the magnitude of High speed Dp/Dm output swing still not meet the + specification, then we can set this value to meet the specification. + $ref: /schemas/types.yaml#/definitions/int32 + default: 0 + minimum: -8 + maximum: 8 + + realtek,disconnection-compensate: + description: + This adjusts the disconnection level compensation for the different + boards with different disconnection level. + $ref: /schemas/types.yaml#/definitions/int32 + default: 0 + minimum: -8 + maximum: 8 + +required: + - compatible + - reg + - "#phy-cells" + +allOf: + - if: + not: + properties: + compatible: + contains: + enum: + - realtek,rtd1619b-usb2phy + then: + properties: + realtek,inverse-hstx-sync-clock: false + + - if: + not: + properties: + compatible: + contains: + enum: + - realtek,rtd1315e-usb2phy + then: + properties: + realtek,driving-level-compensate: false + +additionalProperties: false + +examples: + - | + usb-phy@13214 { + compatible = "realtek,rtd1619b-usb2phy"; + reg = <0x13214 0x4>, <0x28280 0x4>; + #phy-cells = <0>; + nvmem-cells = <&otp_usb_port0_dc_cal>, <&otp_usb_port0_dc_dis>; + nvmem-cell-names = "usb-dc-cal", "usb-dc-dis"; + + realtek,inverse-hstx-sync-clock; + realtek,driving-level = <0xa>; + realtek,disconnection-compensate = <(-1)>; + }; diff --git a/Documentation/devicetree/bindings/phy/realtek,usb3phy.yaml b/Documentation/devicetree/bindings/phy/realtek,usb3phy.yaml new file mode 100644 index 000000000..dfe2bb4e5 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/realtek,usb3phy.yaml @@ -0,0 +1,107 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2023 Realtek Semiconductor Corporation +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/realtek,usb3phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Realtek DHC SoCs USB 3.0 PHY + +maintainers: + - Stanley Chang <stanley_chang@realtek.com> + +description: | + Realtek USB 3.0 PHY support the digital home center (DHC) RTD series SoCs. + The USB 3.0 PHY driver is designed to support the XHCI controller. The SoCs + support multiple XHCI controllers. One PHY device node maps to one XHCI + controller. + + RTD1295/RTD1619 SoCs USB + The USB architecture includes three XHCI controllers. + Each XHCI maps to one USB 2.0 PHY and map one USB 3.0 PHY on some + controllers. + XHCI controller#0 -- usb2phy -- phy#0 + |- usb3phy -- phy#0 + XHCI controller#1 -- usb2phy -- phy#0 + XHCI controller#2 -- usb2phy -- phy#0 + |- usb3phy -- phy#0 + + RTD1319/RTD1619b SoCs USB + The USB architecture includes three XHCI controllers. + Each XHCI maps to one USB 2.0 PHY and map one USB 3.0 PHY on controllers#2. + XHCI controller#0 -- usb2phy -- phy#0 + XHCI controller#1 -- usb2phy -- phy#0 + XHCI controller#2 -- usb2phy -- phy#0 + |- usb3phy -- phy#0 + + RTD1319d SoCs USB + The USB architecture includes three XHCI controllers. + Each xhci maps to one USB 2.0 PHY and map one USB 3.0 PHY on controllers#0. + XHCI controller#0 -- usb2phy -- phy#0 + |- usb3phy -- phy#0 + XHCI controller#1 -- usb2phy -- phy#0 + XHCI controller#2 -- usb2phy -- phy#0 + +properties: + compatible: + enum: + - realtek,rtd1295-usb3phy + - realtek,rtd1319-usb3phy + - realtek,rtd1319d-usb3phy + - realtek,rtd1619-usb3phy + - realtek,rtd1619b-usb3phy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + nvmem-cells: + maxItems: 1 + description: A phandle to the tx lfps swing trim data provided by + a nvmem device, if unspecified, default values shall be used. + + nvmem-cell-names: + items: + - const: usb_u3_tx_lfps_swing_trim + + realtek,amplitude-control-coarse-tuning: + description: + This adjusts the signal amplitude for normal operation and beacon LFPS. + This value is a parameter for coarse tuning. + For different boards, if the default value is inappropriate, this + property can be assigned to adjust. + $ref: /schemas/types.yaml#/definitions/uint32 + default: 255 + minimum: 0 + maximum: 255 + + realtek,amplitude-control-fine-tuning: + description: + This adjusts the signal amplitude for normal operation and beacon LFPS. + This value is used for fine-tuning parameters. + $ref: /schemas/types.yaml#/definitions/uint32 + default: 65535 + minimum: 0 + maximum: 65535 + +required: + - compatible + - reg + - "#phy-cells" + +additionalProperties: false + +examples: + - | + usb-phy@13e10 { + compatible = "realtek,rtd1319d-usb3phy"; + reg = <0x13e10 0x4>; + #phy-cells = <0>; + + nvmem-cells = <&otp_usb_u3_tx_lfps_swing_trim>; + nvmem-cell-names = "usb_u3_tx_lfps_swing_trim"; + + realtek,amplitude-control-coarse-tuning = <0x77>; + }; diff --git a/Documentation/devicetree/bindings/phy/renesas,r8a779f0-ether-serdes.yaml b/Documentation/devicetree/bindings/phy/renesas,r8a779f0-ether-serdes.yaml new file mode 100644 index 000000000..93ab72874 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/renesas,r8a779f0-ether-serdes.yaml @@ -0,0 +1,54 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/renesas,r8a779f0-ether-serdes.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas Ethernet SERDES + +maintainers: + - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> + +properties: + compatible: + const: renesas,r8a779f0-ether-serdes + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + power-domains: + maxItems: 1 + + '#phy-cells': + description: Port number of SERDES. + const: 1 + +required: + - compatible + - reg + - clocks + - resets + - power-domains + - '#phy-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a779f0-cpg-mssr.h> + #include <dt-bindings/power/r8a779f0-sysc.h> + + phy@e6444000 { + compatible = "renesas,r8a779f0-ether-serdes"; + reg = <0xe6444000 0xc00>; + clocks = <&cpg CPG_MOD 1506>; + power-domains = <&sysc R8A779F0_PD_ALWAYS_ON>; + resets = <&cpg 1506>; + #phy-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/phy/renesas,rcar-gen2-usb-phy.yaml b/Documentation/devicetree/bindings/phy/renesas,rcar-gen2-usb-phy.yaml new file mode 100644 index 000000000..afc09f39b --- /dev/null +++ b/Documentation/devicetree/bindings/phy/renesas,rcar-gen2-usb-phy.yaml @@ -0,0 +1,123 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/renesas,rcar-gen2-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car Gen2 USB PHY + +maintainers: + - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> + +properties: + compatible: + items: + - enum: + - renesas,usb-phy-r8a7742 # RZ/G1H + - renesas,usb-phy-r8a7743 # RZ/G1M + - renesas,usb-phy-r8a7744 # RZ/G1N + - renesas,usb-phy-r8a7745 # RZ/G1E + - renesas,usb-phy-r8a77470 # RZ/G1C + - renesas,usb-phy-r8a7790 # R-Car H2 + - renesas,usb-phy-r8a7791 # R-Car M2-W + - renesas,usb-phy-r8a7794 # R-Car E2 + - const: renesas,rcar-gen2-usb-phy # R-Car Gen2 or RZ/G1 + + reg: + maxItems: 1 + + '#address-cells': + const: 1 + + '#size-cells': + const: 0 + + clocks: + maxItems: 1 + + clock-names: + items: + - const: usbhs + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + +patternProperties: + "^usb-phy@[02]$": + type: object + description: Subnode corresponding to a USB channel. + + properties: + reg: + description: FIXME RZ/G1C supports channel 0 only + enum: [0, 2] + + '#phy-cells': + description: | + The phandle's argument in the PHY specifier is the USB controller + selector for the USB channel. + For RZ/G1C: + - 0 for EHCI/OHCI + - 1 for HS-USB + For all other SoCS: + - 0 for PCI EHCI/OHCI + - 1 for HS-USB (channel 0) or xHCI (channel 2) + const: 1 + + required: + - reg + - '#phy-cells' + + additionalProperties: false + +required: + - compatible + - reg + - '#address-cells' + - '#size-cells' + - clocks + - clock-names + - resets + - power-domains + - usb-phy@0 + +if: + properties: + compatible: + contains: + const: renesas,usb-phy-r8a77470 +then: + properties: + usb-phy@2: false +else: + required: + - usb-phy@2 + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7790-cpg-mssr.h> + #include <dt-bindings/power/r8a7790-sysc.h> + usb-phy-controller@e6590100 { + compatible = "renesas,usb-phy-r8a7790", "renesas,rcar-gen2-usb-phy"; + reg = <0xe6590100 0x100>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&cpg CPG_MOD 704>; + clock-names = "usbhs"; + power-domains = <&sysc R8A7790_PD_ALWAYS_ON>; + resets = <&cpg 704>; + + usb0: usb-phy@0 { + reg = <0>; + #phy-cells = <1>; + }; + usb2: usb-phy@2 { + reg = <2>; + #phy-cells = <1>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/renesas,rcar-gen3-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/renesas,rcar-gen3-pcie-phy.yaml new file mode 100644 index 000000000..247ef7c47 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/renesas,rcar-gen3-pcie-phy.yaml @@ -0,0 +1,53 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/renesas,rcar-gen3-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car Generation 3 PCIe PHY + +maintainers: + - Sergei Shtylyov <sergei.shtylyov@gmail.com> + +properties: + compatible: + const: renesas,r8a77980-pcie-phy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + '#phy-cells': + const: 0 + +required: + - compatible + - reg + - clocks + - power-domains + - resets + - '#phy-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a77980-cpg-mssr.h> + #include <dt-bindings/power/r8a77980-sysc.h> + + pcie-phy@e65d0000 { + compatible = "renesas,r8a77980-pcie-phy"; + reg = <0xe65d0000 0x8000>; + #phy-cells = <0>; + clocks = <&cpg CPG_MOD 319>; + power-domains = <&sysc R8A77980_PD_ALWAYS_ON>; + resets = <&cpg 319>; + }; diff --git a/Documentation/devicetree/bindings/phy/renesas,usb2-phy.yaml b/Documentation/devicetree/bindings/phy/renesas,usb2-phy.yaml new file mode 100644 index 000000000..f82649a55 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/renesas,usb2-phy.yaml @@ -0,0 +1,132 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/renesas,usb2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car generation 3 USB 2.0 PHY + +maintainers: + - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> + +properties: + compatible: + oneOf: + - items: + - const: renesas,usb2-phy-r8a77470 # RZ/G1C + + - items: + - enum: + - renesas,usb2-phy-r7s9210 # RZ/A2 + - renesas,usb2-phy-r8a774a1 # RZ/G2M + - renesas,usb2-phy-r8a774b1 # RZ/G2N + - renesas,usb2-phy-r8a774c0 # RZ/G2E + - renesas,usb2-phy-r8a774e1 # RZ/G2H + - renesas,usb2-phy-r8a7795 # R-Car H3 + - renesas,usb2-phy-r8a7796 # R-Car M3-W + - renesas,usb2-phy-r8a77961 # R-Car M3-W+ + - renesas,usb2-phy-r8a77965 # R-Car M3-N + - renesas,usb2-phy-r8a77990 # R-Car E3 + - renesas,usb2-phy-r8a77995 # R-Car D3 + - const: renesas,rcar-gen3-usb2-phy + + - items: + - enum: + - renesas,usb2-phy-r9a07g043 # RZ/G2UL + - renesas,usb2-phy-r9a07g044 # RZ/G2{L,LC} + - renesas,usb2-phy-r9a07g054 # RZ/V2L + - const: renesas,rzg2l-usb2-phy + + reg: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: + minItems: 1 + items: + - const: fck + - const: usb_x1 + + '#phy-cells': + enum: [0, 1] # and 0 is deprecated. + description: | + The phandle's argument in the PHY specifier is the INT_STATUS bit of + controller. + - 1 = USBH_INTA (OHCI) + - 2 = USBH_INTB (EHCI) + - 3 = UCOM_INT (OTG and BC) + + interrupts: + maxItems: 1 + + power-domains: + maxItems: 1 + + resets: + minItems: 1 + items: + - description: reset of USB 2.0 host side + - description: reset of USB 2.0 peripheral side + + vbus-supply: + description: | + Phandle to a regulator that provides power to the VBUS. This regulator + will be managed during the PHY power on/off sequence. + + renesas,no-otg-pins: + $ref: /schemas/types.yaml#/definitions/flag + description: | + specify when a board does not provide proper otg pins. + + dr_mode: true + +if: + properties: + compatible: + contains: + const: renesas,usb2-phy-r7s9210 +then: + required: + - clock-names + +required: + - compatible + - reg + - clocks + - '#phy-cells' + +allOf: + - if: + properties: + compatible: + contains: + const: renesas,rzg2l-usb2-phy + then: + required: + - resets + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + usb-phy@ee080200 { + compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy"; + reg = <0xee080200 0x700>; + interrupts = <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cpg CPG_MOD 703>; + #phy-cells = <1>; + }; + + usb-phy@ee0a0200 { + compatible = "renesas,usb2-phy-r8a7795", "renesas,rcar-gen3-usb2-phy"; + reg = <0xee0a0200 0x700>; + clocks = <&cpg CPG_MOD 702>; + #phy-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/phy/renesas,usb3-phy.yaml b/Documentation/devicetree/bindings/phy/renesas,usb3-phy.yaml new file mode 100644 index 000000000..fe57c5373 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/renesas,usb3-phy.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/renesas,usb3-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Renesas R-Car generation 3 USB 3.0 PHY + +maintainers: + - Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> + +properties: + compatible: + items: + - enum: + - renesas,r8a774a1-usb3-phy # RZ/G2M + - renesas,r8a774b1-usb3-phy # RZ/G2N + - renesas,r8a774e1-usb3-phy # RZ/G2H + - renesas,r8a7795-usb3-phy # R-Car H3 + - renesas,r8a7796-usb3-phy # R-Car M3-W + - renesas,r8a77961-usb3-phy # R-Car M3-W+ + - renesas,r8a77965-usb3-phy # R-Car M3-N + - const: renesas,rcar-gen3-usb3-phy + + reg: + maxItems: 1 + + clocks: + minItems: 2 + maxItems: 3 + + clock-names: + # If you want to use the ssc, the clock-frequency of usb_extal + # must not be 0. + minItems: 2 + items: + - const: usb3-if # The functional clock + - const: usb3s_clk # The usb3's external clock + - const: usb_extal # The usb2's external clock + + '#phy-cells': + # see phy-bindings.txt in the same directory + const: 0 + + power-domains: + maxItems: 1 + + resets: + maxItems: 1 + + renesas,ssc-range: + description: | + Enable/disable spread spectrum clock (ssc). 0 or the property doesn't + exist means disabling the ssc. The actual value will be -<value> ppm. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [ 0, 4003, 4492, 4980 ] + +required: + - compatible + - reg + - clocks + - clock-names + - '#phy-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/r8a7795-cpg-mssr.h> + #include <dt-bindings/power/r8a7795-sysc.h> + + usb-phy@e65ee000 { + compatible = "renesas,r8a7795-usb3-phy", "renesas,rcar-gen3-usb3-phy"; + reg = <0xe65ee000 0x90>; + clocks = <&cpg CPG_MOD 328>, <&usb3s0_clk>, <&usb_extal>; + clock-names = "usb3-if", "usb3s_clk", "usb_extal"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/rockchip,inno-usb2phy.yaml b/Documentation/devicetree/bindings/phy/rockchip,inno-usb2phy.yaml new file mode 100644 index 000000000..525441313 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip,inno-usb2phy.yaml @@ -0,0 +1,203 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/rockchip,inno-usb2phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip USB2.0 phy with inno IP block + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +properties: + compatible: + enum: + - rockchip,px30-usb2phy + - rockchip,rk3128-usb2phy + - rockchip,rk3228-usb2phy + - rockchip,rk3308-usb2phy + - rockchip,rk3328-usb2phy + - rockchip,rk3366-usb2phy + - rockchip,rk3399-usb2phy + - rockchip,rk3568-usb2phy + - rockchip,rk3588-usb2phy + - rockchip,rv1108-usb2phy + + reg: + maxItems: 1 + + clock-output-names: + description: + The usb 480m output clock name. + + "#clock-cells": + const: 0 + + clocks: + maxItems: 1 + + clock-names: + const: phyclk + + assigned-clocks: + description: + Phandle of the usb 480m clock. + + assigned-clock-parents: + description: + Parent of the usb 480m clock. + Select between usb-phy output 480m and xin24m. + Refer to clk/clock-bindings.txt for generic clock consumer properties. + + extcon: + description: + Phandle to the extcon device providing the cable state for the otg phy. + + interrupts: + description: Muxed interrupt for both ports + maxItems: 1 + + resets: + maxItems: 2 + + reset-names: + items: + - const: phy + - const: apb + + rockchip,usbgrf: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to the syscon managing the 'usb general register files'. + When set the driver will request its phandle as one companion-grf + for some special SoCs (e.g rv1108). + + host-port: + type: object + additionalProperties: false + + properties: + "#phy-cells": + const: 0 + + interrupts: + description: host linestate interrupt + maxItems: 1 + + interrupt-names: + const: linestate + + phy-supply: + description: + Phandle to a regulator that provides power to VBUS. + See ./phy-bindings.txt for details. + + required: + - "#phy-cells" + + otg-port: + type: object + additionalProperties: false + + properties: + "#phy-cells": + const: 0 + + interrupts: + minItems: 1 + maxItems: 3 + + interrupt-names: + oneOf: + - const: linestate + - const: otg-mux + - items: + - const: otg-bvalid + - const: otg-id + - const: linestate + + phy-supply: + description: + Phandle to a regulator that provides power to VBUS. + See ./phy-bindings.txt for details. + + required: + - "#phy-cells" + +required: + - compatible + - reg + - clock-output-names + - "#clock-cells" + +anyOf: + - required: + - otg-port + - required: + - host-port + +allOf: + - if: + properties: + compatible: + contains: + enum: + - rockchip,rk3568-usb2phy + - rockchip,rk3588-usb2phy + + then: + properties: + host-port: + properties: + interrupts: false + + otg-port: + properties: + interrupts: false + + required: + - interrupts + + else: + properties: + interrupts: false + + host-port: + required: + - interrupts + - interrupt-names + + otg-port: + required: + - interrupts + - interrupt-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + #include <dt-bindings/interrupt-controller/irq.h> + u2phy0: usb2phy@e450 { + compatible = "rockchip,rk3399-usb2phy"; + reg = <0xe450 0x10>; + clocks = <&cru SCLK_USB2PHY0_REF>; + clock-names = "phyclk"; + clock-output-names = "clk_usbphy0_480m"; + #clock-cells = <0>; + + u2phy0_host: host-port { + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "linestate"; + #phy-cells = <0>; + }; + + u2phy0_otg: otg-port { + interrupts = <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "otg-bvalid", "otg-id", "linestate"; + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml b/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml new file mode 100644 index 000000000..c4fbffcde --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip,pcie3-phy.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/rockchip,pcie3-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip PCIe v3 phy + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +properties: + compatible: + enum: + - rockchip,rk3568-pcie3-phy + - rockchip,rk3588-pcie3-phy + + reg: + maxItems: 1 + + clocks: + minItems: 1 + maxItems: 3 + + clock-names: + minItems: 1 + maxItems: 3 + + data-lanes: + description: which lanes (by position) should be mapped to which + controller (value). 0 means lane disabled, higher value means used. + (controller-number +1 ) + $ref: /schemas/types.yaml#/definitions/uint32-array + minItems: 2 + maxItems: 16 + items: + minimum: 0 + maximum: 16 + + "#phy-cells": + const: 0 + + resets: + maxItems: 1 + + reset-names: + const: phy + + rockchip,phy-grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to the syscon managing the phy "general register files" + + rockchip,pipe-grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle to the syscon managing the pipe "general register files" + +required: + - compatible + - reg + - rockchip,phy-grf + - "#phy-cells" + +allOf: + - if: + properties: + compatible: + enum: + - rockchip,rk3588-pcie3-phy + then: + properties: + clocks: + maxItems: 1 + clock-names: + items: + - const: pclk + else: + properties: + clocks: + minItems: 3 + + clock-names: + items: + - const: refclk_m + - const: refclk_n + - const: pclk + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3568-cru.h> + pcie30phy: phy@fe8c0000 { + compatible = "rockchip,rk3568-pcie3-phy"; + reg = <0xfe8c0000 0x20000>; + #phy-cells = <0>; + clocks = <&pmucru CLK_PCIE30PHY_REF_M>, + <&pmucru CLK_PCIE30PHY_REF_N>, + <&cru PCLK_PCIE30PHY>; + clock-names = "refclk_m", "refclk_n", "pclk"; + resets = <&cru SRST_PCIE30PHY>; + reset-names = "phy"; + rockchip,phy-grf = <&pcie30_phy_grf>; + }; diff --git a/Documentation/devicetree/bindings/phy/rockchip,px30-dsi-dphy.yaml b/Documentation/devicetree/bindings/phy/rockchip,px30-dsi-dphy.yaml new file mode 100644 index 000000000..46e64fa29 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip,px30-dsi-dphy.yaml @@ -0,0 +1,72 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/rockchip,px30-dsi-dphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip MIPI DPHY with additional LVDS/TTL modes + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +properties: + "#phy-cells": + const: 0 + + compatible: + enum: + - rockchip,px30-dsi-dphy + - rockchip,rk3128-dsi-dphy + - rockchip,rk3368-dsi-dphy + - rockchip,rk3568-dsi-dphy + - rockchip,rv1126-dsi-dphy + + reg: + maxItems: 1 + + clocks: + items: + - description: PLL reference clock + - description: Module clock + + clock-names: + items: + - const: ref + - const: pclk + + power-domains: + maxItems: 1 + description: phandle to the associated power domain + + resets: + items: + - description: exclusive PHY reset line + + reset-names: + items: + - const: apb + +required: + - "#phy-cells" + - compatible + - reg + - clocks + - clock-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + dsi_dphy: phy@ff2e0000 { + compatible = "rockchip,px30-dsi-dphy"; + reg = <0xff2e0000 0x10000>; + clocks = <&pmucru 13>, <&cru 12>; + clock-names = "ref", "pclk"; + resets = <&cru 12>; + reset-names = "apb"; + #phy-cells = <0>; + }; + +... diff --git a/Documentation/devicetree/bindings/phy/rockchip,rk3288-dp-phy.yaml b/Documentation/devicetree/bindings/phy/rockchip,rk3288-dp-phy.yaml new file mode 100644 index 000000000..2538235c5 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip,rk3288-dp-phy.yaml @@ -0,0 +1,41 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/rockchip,rk3288-dp-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip specific extensions to the Analogix Display Port PHY + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +properties: + compatible: + const: rockchip,rk3288-dp-phy + + clocks: + maxItems: 1 + + clock-names: + const: 24m + + "#phy-cells": + const: 0 + +required: + - compatible + - clocks + - clock-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/rk3288-cru.h> + edp-phy { + compatible = "rockchip,rk3288-dp-phy"; + clocks = <&cru SCLK_EDP_24M>; + clock-names = "24m"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt new file mode 100644 index 000000000..57d28c0d5 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-emmc-phy.txt @@ -0,0 +1,43 @@ +Rockchip EMMC PHY +----------------------- + +Required properties: + - compatible: rockchip,rk3399-emmc-phy + - #phy-cells: must be 0 + - reg: PHY register address offset and length in "general + register files" + +Optional properties: + - clock-names: Should contain "emmcclk". Although this is listed as optional + (because most boards can get basic functionality without having + access to it), it is strongly suggested. + See ../clock/clock-bindings.txt for details. + - clocks: Should have a phandle to the card clock exported by the SDHCI driver. + - drive-impedance-ohm: Specifies the drive impedance in Ohm. + Possible values are 33, 40, 50, 66 and 100. + If not set, the default value of 50 will be applied. + - rockchip,enable-strobe-pulldown: Enable internal pull-down for the strobe + line. If not set, pull-down is not used. + - rockchip,output-tapdelay-select: Specifies the phyctrl_otapdlysec register. + If not set, the register defaults to 0x4. + Maximum value 0xf. + +Example: + + +grf: syscon@ff770000 { + compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + +... + + emmcphy: phy@f780 { + compatible = "rockchip,rk3399-emmc-phy"; + reg = <0xf780 0x20>; + clocks = <&sdhci>; + clock-names = "emmcclk"; + drive-impedance-ohm = <50>; + #phy-cells = <0>; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/rockchip-inno-csi-dphy.yaml b/Documentation/devicetree/bindings/phy/rockchip-inno-csi-dphy.yaml new file mode 100644 index 000000000..5ac994b3c --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-inno-csi-dphy.yaml @@ -0,0 +1,80 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/rockchip-inno-csi-dphy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip SoC MIPI RX0 D-PHY + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +description: | + The Rockchip SoC has a MIPI CSI D-PHY based on an Innosilicon IP which + connects to the ISP1 (Image Signal Processing unit v1.0) for CSI cameras. + +properties: + compatible: + enum: + - rockchip,px30-csi-dphy + - rockchip,rk1808-csi-dphy + - rockchip,rk3326-csi-dphy + - rockchip,rk3368-csi-dphy + - rockchip,rk3568-csi-dphy + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + clock-names: + const: pclk + + '#phy-cells': + const: 0 + + power-domains: + description: Video in/out power domain. + maxItems: 1 + + resets: + items: + - description: exclusive PHY reset line + + reset-names: + items: + - const: apb + + rockchip,grf: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Some additional phy settings are access through GRF regs. + +required: + - compatible + - reg + - clocks + - clock-names + - '#phy-cells' + - power-domains + - resets + - reset-names + - rockchip,grf + +additionalProperties: false + +examples: + - | + + csi_dphy: phy@ff2f0000 { + compatible = "rockchip,px30-csi-dphy"; + reg = <0xff2f0000 0x4000>; + clocks = <&cru 1>; + clock-names = "pclk"; + #phy-cells = <0>; + power-domains = <&power 1>; + resets = <&cru 1>; + reset-names = "apb"; + rockchip,grf = <&grf>; + }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-mipi-dphy-rx0.yaml b/Documentation/devicetree/bindings/phy/rockchip-mipi-dphy-rx0.yaml new file mode 100644 index 000000000..5114e99b0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-mipi-dphy-rx0.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: (GPL-2.0+ OR MIT) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/rockchip-mipi-dphy-rx0.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip SoC MIPI RX0 D-PHY + +maintainers: + - Helen Koike <helen.koike@collabora.com> + - Ezequiel Garcia <ezequiel@collabora.com> + +description: | + The Rockchip SoC has a MIPI D-PHY bus with an RX0 entry which connects to + the ISP1 (Image Signal Processing unit v1.0) for CSI cameras. + +properties: + compatible: + const: rockchip,rk3399-mipi-dphy-rx0 + + clocks: + items: + - description: MIPI D-PHY ref clock + - description: MIPI D-PHY RX0 cfg clock + - description: Video in/out general register file clock + + clock-names: + items: + - const: dphy-ref + - const: dphy-cfg + - const: grf + + '#phy-cells': + const: 0 + + power-domains: + description: Video in/out power domain. + maxItems: 1 + +required: + - compatible + - clocks + - clock-names + - '#phy-cells' + - power-domains + +additionalProperties: false + +examples: + - | + + /* + * MIPI D-PHY RX0 use registers in "general register files", it + * should be a child of the GRF. + * + * grf: syscon@ff770000 { + * compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd"; + * ... + * }; + */ + + #include <dt-bindings/clock/rk3399-cru.h> + #include <dt-bindings/power/rk3399-power.h> + + mipi_dphy_rx0: mipi-dphy-rx0 { + compatible = "rockchip,rk3399-mipi-dphy-rx0"; + clocks = <&cru SCLK_MIPIDPHY_REF>, + <&cru SCLK_DPHY_RX0_CFG>, + <&cru PCLK_VIO_GRF>; + clock-names = "dphy-ref", "dphy-cfg", "grf"; + power-domains = <&power RK3399_PD_VIO>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt b/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt new file mode 100644 index 000000000..b496042f1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-pcie-phy.txt @@ -0,0 +1,36 @@ +Rockchip PCIE PHY +----------------------- + +Required properties: + - compatible: rockchip,rk3399-pcie-phy + - clocks: Must contain an entry in clock-names. + See ../clocks/clock-bindings.txt for details. + - clock-names: Must be "refclk" + - resets: Must contain an entry in reset-names. + See ../reset/reset.txt for details. + - reset-names: Must be "phy" + +Required properties for legacy PHY mode (deprecated): + - #phy-cells: must be 0 + +Required properties for per-lane PHY mode (preferred): + - #phy-cells: must be 1 + +Example: + +grf: syscon@ff770000 { + compatible = "rockchip,rk3399-grf", "syscon", "simple-mfd"; + #address-cells = <1>; + #size-cells = <1>; + + ... + + pcie_phy: pcie-phy { + compatible = "rockchip,rk3399-pcie-phy"; + #phy-cells = <0>; + clocks = <&cru SCLK_PCIEPHY_REF>; + clock-names = "refclk"; + resets = <&cru SRST_PCIEPHY>; + reset-names = "phy"; + }; +}; diff --git a/Documentation/devicetree/bindings/phy/rockchip-usb-phy.yaml b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.yaml new file mode 100644 index 000000000..499d55131 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/rockchip-usb-phy.yaml @@ -0,0 +1,78 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/rockchip-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Rockchip USB2.0 phy + +maintainers: + - Heiko Stuebner <heiko@sntech.de> + +properties: + compatible: + enum: + - rockchip,rk3066a-usb-phy + - rockchip,rk3188-usb-phy + - rockchip,rk3288-usb-phy + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +required: + - compatible + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +patternProperties: + "usb-phy@[0-9a-f]+$": + type: object + + properties: + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + maxItems: 1 + + clock-names: + const: phyclk + + "#clock-cells": + const: 0 + + resets: + maxItems: 1 + + reset-names: + const: phy-reset + + vbus-supply: + description: phandle for vbus power source + + required: + - reg + - "#phy-cells" + + additionalProperties: false + +examples: + - | + usbphy: usbphy { + compatible = "rockchip,rk3288-usb-phy"; + #address-cells = <1>; + #size-cells = <0>; + + usbphy0: usb-phy@320 { + reg = <0x320>; + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/samsung,dp-video-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,dp-video-phy.yaml new file mode 100644 index 000000000..3bee3f873 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/samsung,dp-video-phy.yaml @@ -0,0 +1,40 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/samsung,dp-video-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos SoC DisplayPort PHY + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Marek Szyprowski <m.szyprowski@samsung.com> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +properties: + compatible: + enum: + - samsung,exynos5250-dp-video-phy + - samsung,exynos5420-dp-video-phy + + "#phy-cells": + const: 0 + + samsung,pmu-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + deprecated: true + description: + Phandle to PMU system controller interface (if not a child of PMU). + +required: + - compatible + - "#phy-cells" + +additionalProperties: false + +examples: + - | + phy { + compatible = "samsung,exynos5420-dp-video-phy"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/samsung,exynos-hdmi-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,exynos-hdmi-phy.yaml new file mode 100644 index 000000000..efc679c38 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/samsung,exynos-hdmi-phy.yaml @@ -0,0 +1,43 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/samsung,exynos-hdmi-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos SoC HDMI PHY + +maintainers: + - Inki Dae <inki.dae@samsung.com> + - Seung-Woo Kim <sw0312.kim@samsung.com> + - Kyungmin Park <kyungmin.park@samsung.com> + - Krzysztof Kozlowski <krzk@kernel.org> + +properties: + compatible: + oneOf: + - enum: + - samsung,exynos4210-hdmiphy + - samsung,exynos4212-hdmiphy + - const: samsung,exynos5-hdmiphy + deprecated: true + + reg: + maxItems: 1 + +required: + - compatible + - reg + +additionalProperties: false + +examples: + - | + i2c { + #address-cells = <1>; + #size-cells = <0>; + + hdmi-phy@38 { + compatible = "samsung,exynos4210-hdmiphy"; + reg = <0x38>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/samsung,exynos-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,exynos-pcie-phy.yaml new file mode 100644 index 000000000..41df8bb08 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/samsung,exynos-pcie-phy.yaml @@ -0,0 +1,51 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/samsung,exynos-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung SoC series PCIe PHY + +maintainers: + - Marek Szyprowski <m.szyprowski@samsung.com> + - Jaehoon Chung <jh80.chung@samsung.com> + +properties: + "#phy-cells": + const: 0 + + compatible: + const: samsung,exynos5433-pcie-phy + + reg: + maxItems: 1 + + samsung,pmu-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle for PMU system controller interface, used to + control PMU registers bits for PCIe PHY + + samsung,fsys-sysreg: + $ref: /schemas/types.yaml#/definitions/phandle + description: phandle for FSYS sysreg interface, used to control + sysreg registers bits for PCIe PHY + +required: + - "#phy-cells" + - compatible + - reg + - samsung,pmu-syscon + - samsung,fsys-sysreg + +additionalProperties: false + +examples: + - | + pcie_phy: pcie-phy@15680000 { + compatible = "samsung,exynos5433-pcie-phy"; + reg = <0x15680000 0x1000>; + samsung,pmu-syscon = <&pmu_system_controller>; + samsung,fsys-sysreg = <&syscon_fsys>; + #phy-cells = <0>; + }; +... diff --git a/Documentation/devicetree/bindings/phy/samsung,exynos5250-sata-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,exynos5250-sata-phy.yaml new file mode 100644 index 000000000..8751e5594 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/samsung,exynos5250-sata-phy.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/samsung,exynos5250-sata-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos5250 SoC SATA PHY + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Marek Szyprowski <m.szyprowski@samsung.com> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +properties: + compatible: + const: samsung,exynos5250-sata-phy + + clocks: + maxItems: 1 + + clock-names: + items: + - const: sata_phyctrl + + "#phy-cells": + const: 0 + + reg: + maxItems: 1 + + samsung,syscon-phandle: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to PMU system controller interface. + + samsung,exynos-sataphy-i2c-phandle: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to I2C SATA interface. + +required: + - compatible + - clocks + - clock-names + - "#phy-cells" + - reg + - samsung,syscon-phandle + - samsung,exynos-sataphy-i2c-phandle + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos5250.h> + + phy@12170000 { + compatible = "samsung,exynos5250-sata-phy"; + reg = <0x12170000 0x1ff>; + clocks = <&clock CLK_SATA_PHYCTRL>; + clock-names = "sata_phyctrl"; + #phy-cells = <0>; + samsung,syscon-phandle = <&pmu_system_controller>; + samsung,exynos-sataphy-i2c-phandle = <&sata_phy_i2c>; + }; diff --git a/Documentation/devicetree/bindings/phy/samsung,mipi-video-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,mipi-video-phy.yaml new file mode 100644 index 000000000..b2250e4a6 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/samsung,mipi-video-phy.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/samsung,mipi-video-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5P/Exynos SoC MIPI CSIS/DSIM DPHY + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Marek Szyprowski <m.szyprowski@samsung.com> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +description: | + For samsung,s5pv210-mipi-video-phy compatible PHYs the second cell in the + PHY specifier identifies the PHY and its meaning is as follows:: + 0 - MIPI CSIS 0, + 1 - MIPI DSIM 0, + 2 - MIPI CSIS 1, + 3 - MIPI DSIM 1. + + samsung,exynos5420-mipi-video-phy and samsung,exynos5433-mipi-video-phy + support additional fifth PHY:: + 4 - MIPI CSIS 2. + +properties: + compatible: + enum: + - samsung,s5pv210-mipi-video-phy + - samsung,exynos5420-mipi-video-phy + - samsung,exynos5433-mipi-video-phy + + "#phy-cells": + const: 1 + + syscon: + $ref: /schemas/types.yaml#/definitions/phandle + deprecated: true + description: + Phandle to PMU system controller interface, valid only for + samsung,s5pv210-mipi-video-phy and samsung,exynos5420-mipi-video-phy (if + not a child of PMU). + + samsung,pmu-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + deprecated: true + description: + Phandle to PMU system controller interface, valid for + samsung,exynos5433-mipi-video-phy (if not a child of PMU). + + samsung,disp-sysreg: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to DISP system controller interface, valid for + samsung,exynos5433-mipi-video-phy. + + samsung,cam0-sysreg: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to CAM0 system controller interface, valid for + samsung,exynos5433-mipi-video-phy. + + samsung,cam1-sysreg: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to CAM1 system controller interface, valid for + samsung,exynos5433-mipi-video-phy. + +required: + - compatible + - "#phy-cells" + +allOf: + - if: + properties: + compatible: + contains: + enum: + - samsung,s5pv210-mipi-video-phy + - samsung,exynos5420-mipi-video-phy + then: + properties: + samsung,pmu-syscon: false + samsung,disp-sysreg: false + samsung,cam0-sysreg: false + samsung,cam1-sysreg: false + else: + properties: + syscon: false + required: + - samsung,disp-sysreg + - samsung,cam0-sysreg + - samsung,cam1-sysreg + +additionalProperties: false + +examples: + - | + phy { + compatible = "samsung,exynos5433-mipi-video-phy"; + #phy-cells = <1>; + samsung,cam0-sysreg = <&syscon_cam0>; + samsung,cam1-sysreg = <&syscon_cam1>; + samsung,disp-sysreg = <&syscon_disp>; + }; + + - | + phy { + compatible = "samsung,s5pv210-mipi-video-phy"; + syscon = <&pmu_system_controller>; + #phy-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml new file mode 100644 index 000000000..782f975b4 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/samsung,ufs-phy.yaml @@ -0,0 +1,112 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/samsung,ufs-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung SoC series UFS PHY + +maintainers: + - Alim Akhtar <alim.akhtar@samsung.com> + +properties: + "#phy-cells": + const: 0 + + compatible: + enum: + - samsung,exynos7-ufs-phy + - samsung,exynosautov9-ufs-phy + - tesla,fsd-ufs-phy + + reg: + maxItems: 1 + + reg-names: + items: + - const: phy-pma + + clocks: + minItems: 1 + maxItems: 4 + + clock-names: + minItems: 1 + maxItems: 4 + + samsung,pmu-syscon: + $ref: /schemas/types.yaml#/definitions/phandle-array + maxItems: 1 + items: + minItems: 1 + items: + - description: phandle for PMU system controller interface, used to + control pmu registers bits for ufs m-phy + - description: offset of the pmu control register + description: + It can be phandle/offset pair. The second cell which can represent an + offset is optional. + +required: + - "#phy-cells" + - compatible + - reg + - reg-names + - clocks + - clock-names + - samsung,pmu-syscon + +allOf: + - if: + properties: + compatible: + contains: + const: samsung,exynos7-ufs-phy + + then: + properties: + clocks: + items: + - description: PLL reference clock + - description: symbol clock for input symbol (rx0-ch0 symbol clock) + - description: symbol clock for input symbol (rx1-ch1 symbol clock) + - description: symbol clock for output symbol (tx0 symbol clock) + + clock-names: + items: + - const: ref_clk + - const: rx1_symbol_clk + - const: rx0_symbol_clk + - const: tx0_symbol_clk + + else: + properties: + clocks: + items: + - description: PLL reference clock + + clock-names: + items: + - const: ref_clk + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos7-clk.h> + + ufs_phy: ufs-phy@15571800 { + compatible = "samsung,exynos7-ufs-phy"; + reg = <0x15571800 0x240>; + reg-names = "phy-pma"; + samsung,pmu-syscon = <&pmu_system_controller>; + #phy-cells = <0>; + clocks = <&clock_fsys1 SCLK_COMBO_PHY_EMBEDDED_26M>, + <&clock_fsys1 PHYCLK_UFS20_RX1_SYMBOL_USER>, + <&clock_fsys1 PHYCLK_UFS20_RX0_SYMBOL_USER>, + <&clock_fsys1 PHYCLK_UFS20_TX0_SYMBOL_USER>; + clock-names = "ref_clk", "rx1_symbol_clk", + "rx0_symbol_clk", "tx0_symbol_clk"; + + }; +... diff --git a/Documentation/devicetree/bindings/phy/samsung,usb2-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,usb2-phy.yaml new file mode 100644 index 000000000..d9f22a801 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/samsung,usb2-phy.yaml @@ -0,0 +1,102 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/samsung,usb2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung S5P/Exynos SoC USB 2.0 PHY + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Marek Szyprowski <m.szyprowski@samsung.com> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +description: | + The first phandle argument in the PHY specifier identifies the PHY, its + meaning is compatible dependent. For the currently supported SoCs (Exynos4210 + and Exynos4212) it is as follows:: + 0 - USB device ("device"), + 1 - USB host ("host"), + 2 - HSIC0 ("hsic0"), + 3 - HSIC1 ("hsic1"), + Exynos3250 has only USB device phy available as phy 0. + + Exynos4210 and Exynos4212 use mode switching and require that mode switch + register is supplied. + +properties: + compatible: + enum: + - samsung,exynos3250-usb2-phy + - samsung,exynos4210-usb2-phy + - samsung,exynos4x12-usb2-phy + - samsung,exynos5250-usb2-phy + - samsung,exynos5420-usb2-phy + - samsung,s5pv210-usb2-phy + + clocks: + items: + - description: PHY module gate clock. + - description: Reference rate clock of PHY module. + + clock-names: + items: + - const: phy + - const: ref + + "#phy-cells": + const: 1 + + reg: + maxItems: 1 + + samsung,pmureg-phandle: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to PMU system controller interface. + + samsung,sysreg-phandle: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to system registers interface. + + vbus-supply: + description: + VBUS power source. + +required: + - compatible + - clocks + - clock-names + - "#phy-cells" + - reg + - samsung,pmureg-phandle + +allOf: + - if: + properties: + compatible: + contains: + enum: + - samsung,exynos4x12-usb2-phy + - samsung,exynos5250-usb2-phy + - samsung,exynos5420-usb2-phy + then: + required: + - samsung,sysreg-phandle + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos5420.h> + + phy@12130000 { + compatible = "samsung,exynos5420-usb2-phy"; + reg = <0x12130000 0x100>; + #phy-cells = <1>; + clocks = <&clock CLK_USBH20>, <&clock CLK_SCLK_USBPHY300>; + clock-names = "phy", "ref"; + samsung,sysreg-phandle = <&sysreg_system_controller>; + samsung,pmureg-phandle = <&pmu_system_controller>; + }; diff --git a/Documentation/devicetree/bindings/phy/samsung,usb3-drd-phy.yaml b/Documentation/devicetree/bindings/phy/samsung,usb3-drd-phy.yaml new file mode 100644 index 000000000..452e584d9 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/samsung,usb3-drd-phy.yaml @@ -0,0 +1,127 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/samsung,usb3-drd-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Samsung Exynos SoC USB 3.0 DRD PHY USB 2.0 PHY + +maintainers: + - Krzysztof Kozlowski <krzk@kernel.org> + - Marek Szyprowski <m.szyprowski@samsung.com> + - Sylwester Nawrocki <s.nawrocki@samsung.com> + +description: | + For samsung,exynos5250-usbdrd-phy and samsung,exynos5420-usbdrd-phy + compatible PHYs, the second cell in the PHY specifier identifies the + PHY id, which is interpreted as follows:: + 0 - UTMI+ type phy, + 1 - PIPE3 type phy. + + For SoCs like Exynos5420 having multiple USB 3.0 DRD PHY controllers, + 'usbdrd_phy' nodes should have numbered alias in the aliases node, in the + form of usbdrdphyN, N = 0, 1... (depending on number of controllers). + +properties: + compatible: + enum: + - samsung,exynos5250-usbdrd-phy + - samsung,exynos5420-usbdrd-phy + - samsung,exynos5433-usbdrd-phy + - samsung,exynos7-usbdrd-phy + - samsung,exynos850-usbdrd-phy + + clocks: + minItems: 2 + maxItems: 5 + + clock-names: + minItems: 2 + maxItems: 5 + description: | + At least two clocks:: + - Main PHY clock (same as USB DRD controller i.e. DWC3 IP clock), used + for register access. + - PHY reference clock (usually crystal clock), used for PHY operations, + associated by phy name. It is used to determine bit values for clock + settings register. For Exynos5420 this is given as 'sclk_usbphy30' + in the CMU. + + "#phy-cells": + const: 1 + + port: + $ref: /schemas/graph.yaml#/properties/port + description: + Any connector to the data bus of this controller should be modelled using + the OF graph bindings specified. + + reg: + maxItems: 1 + + samsung,pmu-syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: + Phandle to PMU system controller interface. + + vbus-supply: + description: + VBUS power source. + + vbus-boost-supply: + description: + VBUS Boost 5V power source. + +required: + - compatible + - clocks + - clock-names + - "#phy-cells" + - reg + - samsung,pmu-syscon + +allOf: + - if: + properties: + compatible: + contains: + enum: + - samsung,exynos5433-usbdrd-phy + - samsung,exynos7-usbdrd-phy + then: + properties: + clocks: + minItems: 5 + maxItems: 5 + clock-names: + items: + - const: phy + - const: ref + - const: phy_utmi + - const: phy_pipe + - const: itp + else: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + items: + - const: phy + - const: ref + +additionalProperties: false + +examples: + - | + #include <dt-bindings/clock/exynos5420.h> + + phy@12100000 { + compatible = "samsung,exynos5420-usbdrd-phy"; + reg = <0x12100000 0x100>; + #phy-cells = <1>; + clocks = <&clock CLK_USBD300>, <&clock CLK_SCLK_USBPHY300>; + clock-names = "phy", "ref"; + samsung,pmu-syscon = <&pmu_system_controller>; + vbus-supply = <&usb300_vbus_reg>; + }; diff --git a/Documentation/devicetree/bindings/phy/socionext,uniphier-ahci-phy.yaml b/Documentation/devicetree/bindings/phy/socionext,uniphier-ahci-phy.yaml new file mode 100644 index 000000000..de3cffc85 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/socionext,uniphier-ahci-phy.yaml @@ -0,0 +1,128 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/socionext,uniphier-ahci-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Socionext UniPhier AHCI PHY + +description: | + This describes the deivcetree bindings for PHY interfaces built into + AHCI controller implemented on Socionext UniPhier SoCs. + +maintainers: + - Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +properties: + compatible: + enum: + - socionext,uniphier-pro4-ahci-phy + - socionext,uniphier-pxs2-ahci-phy + - socionext,uniphier-pxs3-ahci-phy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: true + + resets: + minItems: 2 + maxItems: 6 + + reset-names: true + +allOf: + - if: + properties: + compatible: + contains: + const: socionext,uniphier-pro4-ahci-phy + then: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + items: + - const: link + - const: gio + resets: + minItems: 6 + maxItems: 6 + reset-names: + items: + - const: link + - const: gio + - const: phy + - const: pm + - const: tx + - const: rx + - if: + properties: + compatible: + contains: + const: socionext,uniphier-pxs2-ahci-phy + then: + properties: + clocks: + maxItems: 1 + clock-names: + const: link + resets: + minItems: 2 + maxItems: 2 + reset-names: + items: + - const: link + - const: phy + - if: + properties: + compatible: + contains: + const: socionext,uniphier-pxs3-ahci-phy + then: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + items: + - const: link + - const: phy + resets: + minItems: 2 + maxItems: 2 + reset-names: + items: + - const: link + - const: phy + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + ahci_phy: phy@10 { + compatible = "socionext,uniphier-pxs3-ahci-phy"; + reg = <0x10 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy"; + clocks = <&sys_clk 28>, <&sys_clk 30>; + reset-names = "link", "phy"; + resets = <&sys_rst 28>, <&sys_rst 30>; + }; diff --git a/Documentation/devicetree/bindings/phy/socionext,uniphier-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/socionext,uniphier-pcie-phy.yaml new file mode 100644 index 000000000..b3ed2f74a --- /dev/null +++ b/Documentation/devicetree/bindings/phy/socionext,uniphier-pcie-phy.yaml @@ -0,0 +1,101 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/socionext,uniphier-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Socionext UniPhier PCIe PHY + +description: | + This describes the devicetree bindings for PHY interface built into + PCIe controller implemented on Socionext UniPhier SoCs. + +maintainers: + - Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +properties: + compatible: + enum: + - socionext,uniphier-pro5-pcie-phy + - socionext,uniphier-ld20-pcie-phy + - socionext,uniphier-pxs3-pcie-phy + - socionext,uniphier-nx1-pcie-phy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + minItems: 1 + maxItems: 2 + + clock-names: true + + resets: + minItems: 1 + maxItems: 2 + + reset-names: true + + socionext,syscon: + $ref: /schemas/types.yaml#/definitions/phandle + description: A phandle to system control to set configurations for phy + +allOf: + - if: + properties: + compatible: + contains: + const: socionext,uniphier-pro5-pcie-phy + then: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + items: + - const: gio + - const: link + resets: + minItems: 2 + maxItems: 2 + reset-names: + items: + - const: gio + - const: link + else: + properties: + clocks: + maxItems: 1 + clock-names: + const: link + resets: + maxItems: 1 + reset-names: + const: link + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + pcie_phy: phy@66038000 { + compatible = "socionext,uniphier-ld20-pcie-phy"; + reg = <0x66038000 0x4000>; + #phy-cells = <0>; + clock-names = "link"; + clocks = <&sys_clk 24>; + reset-names = "link"; + resets = <&sys_rst 24>; + socionext,syscon = <&soc_glue>; + }; diff --git a/Documentation/devicetree/bindings/phy/socionext,uniphier-usb2-phy.yaml b/Documentation/devicetree/bindings/phy/socionext,uniphier-usb2-phy.yaml new file mode 100644 index 000000000..19522c54f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/socionext,uniphier-usb2-phy.yaml @@ -0,0 +1,83 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/socionext,uniphier-usb2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Socionext UniPhier USB2 PHY + +description: | + This describes the devicetree bindings for PHY interface built into + USB2 controller implemented on Socionext UniPhier SoCs. + Pro4 SoC has both USB2 and USB3 host controllers, however, this USB3 + controller doesn't include its own High-Speed PHY. This needs to specify + USB2 PHY instead of USB3 HS-PHY. + +maintainers: + - Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +properties: + compatible: + enum: + - socionext,uniphier-pro4-usb2-phy + - socionext,uniphier-ld11-usb2-phy + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + +patternProperties: + "^phy@[0-9]+$": + type: object + additionalProperties: false + + properties: + reg: + minimum: 0 + maximum: 3 + description: + The ID number for the PHY + + "#phy-cells": + const: 0 + + vbus-supply: + description: A phandle to the regulator for USB VBUS, only for USB host + + required: + - reg + - "#phy-cells" + +required: + - compatible + - "#address-cells" + - "#size-cells" + +additionalProperties: false + +examples: + - | + // The UniPhier usb2-phy should be a subnode of a "syscon" compatible node. + + usb-hub { + compatible = "socionext,uniphier-ld11-usb2-phy"; + #address-cells = <1>; + #size-cells = <0>; + + usb_phy0: phy@0 { + reg = <0>; + #phy-cells = <0>; + }; + + usb_phy1: phy@1 { + reg = <1>; + #phy-cells = <0>; + }; + + usb_phy2: phy@2 { + reg = <2>; + #phy-cells = <0>; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/socionext,uniphier-usb3hs-phy.yaml b/Documentation/devicetree/bindings/phy/socionext,uniphier-usb3hs-phy.yaml new file mode 100644 index 000000000..2107d98ac --- /dev/null +++ b/Documentation/devicetree/bindings/phy/socionext,uniphier-usb3hs-phy.yaml @@ -0,0 +1,160 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/socionext,uniphier-usb3hs-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Socionext UniPhier USB3 High-Speed (HS) PHY + +description: | + This describes the devicetree bindings for PHY interfaces built into + USB3 controller implemented on Socionext UniPhier SoCs. + Although the controller includes High-Speed PHY and Super-Speed PHY, + this describes about High-Speed PHY. + +maintainers: + - Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +properties: + compatible: + enum: + - socionext,uniphier-pro5-usb3-hsphy + - socionext,uniphier-pxs2-usb3-hsphy + - socionext,uniphier-ld20-usb3-hsphy + - socionext,uniphier-pxs3-usb3-hsphy + - socionext,uniphier-nx1-usb3-hsphy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + minItems: 2 + maxItems: 3 + + clock-names: true + + resets: + maxItems: 2 + + reset-names: true + + vbus-supply: + description: A phandle to the regulator for USB VBUS + + nvmem-cells: + maxItems: 3 + description: + Phandles to nvmem cell that contains the trimming data. + Available only for HS-PHY implemented on LD20 and PXs3, and + if unspecified, default value is used. + + nvmem-cell-names: + items: + - const: rterm + - const: sel_t + - const: hs_i + description: + Should be the following names, which correspond to each nvmem-cells. + All of the 3 parameters associated with the above names are + required for each port, if any one is omitted, the trimming data + of the port will not be set at all. + +allOf: + - if: + properties: + compatible: + contains: + const: socionext,uniphier-pro5-usb3-hsphy + then: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + items: + - const: gio + - const: link + resets: + minItems: 2 + maxItems: 2 + reset-names: + items: + - const: gio + - const: link + - if: + properties: + compatible: + contains: + enum: + - socionext,uniphier-pxs2-usb3-hsphy + - socionext,uniphier-ld20-usb3-hsphy + then: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + items: + - const: link + - const: phy + resets: + minItems: 2 + maxItems: 2 + reset-names: + items: + - const: link + - const: phy + - if: + properties: + compatible: + contains: + enum: + - socionext,uniphier-pxs3-usb3-hsphy + - socionext,uniphier-nx1-usb3-hsphy + then: + properties: + clocks: + minItems: 2 + maxItems: 3 + clock-names: + minItems: 2 + items: + - const: link + - const: phy + - const: phy-ext + resets: + minItems: 2 + maxItems: 2 + reset-names: + items: + - const: link + - const: phy + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + usb_hsphy0: phy@200 { + compatible = "socionext,uniphier-ld20-usb3-hsphy"; + reg = <0x200 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy"; + clocks = <&sys_clk 14>, <&sys_clk 16>; + reset-names = "link", "phy"; + resets = <&sys_rst 14>, <&sys_rst 16>; + vbus-supply = <&usb_vbus0>; + nvmem-cell-names = "rterm", "sel_t", "hs_i"; + nvmem-cells = <&usb_rterm0>, <&usb_sel_t0>, <&usb_hs_i0>; + }; diff --git a/Documentation/devicetree/bindings/phy/socionext,uniphier-usb3ss-phy.yaml b/Documentation/devicetree/bindings/phy/socionext,uniphier-usb3ss-phy.yaml new file mode 100644 index 000000000..8f5aa6238 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/socionext,uniphier-usb3ss-phy.yaml @@ -0,0 +1,143 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/socionext,uniphier-usb3ss-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Socionext UniPhier USB3 Super-Speed (SS) PHY + +description: | + This describes the devicetree bindings for PHY interfaces built into + USB3 controller implemented on Socionext UniPhier SoCs. + Although the controller includes High-Speed PHY and Super-Speed PHY, + this describes about Super-Speed PHY. + +maintainers: + - Kunihiko Hayashi <hayashi.kunihiko@socionext.com> + +properties: + compatible: + enum: + - socionext,uniphier-pro4-usb3-ssphy + - socionext,uniphier-pro5-usb3-ssphy + - socionext,uniphier-pxs2-usb3-ssphy + - socionext,uniphier-ld20-usb3-ssphy + - socionext,uniphier-pxs3-usb3-ssphy + - socionext,uniphier-nx1-usb3-ssphy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + minItems: 2 + maxItems: 3 + + clock-names: true + + resets: + maxItems: 2 + + reset-names: true + + vbus-supply: + description: A phandle to the regulator for USB VBUS, only for USB host + +allOf: + - if: + properties: + compatible: + contains: + enum: + - socionext,uniphier-pro4-usb3-ssphy + - socionext,uniphier-pro5-usb3-ssphy + then: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + items: + - const: gio + - const: link + resets: + minItems: 2 + maxItems: 2 + reset-names: + items: + - const: gio + - const: link + - if: + properties: + compatible: + contains: + enum: + - socionext,uniphier-pxs2-usb3-ssphy + - socionext,uniphier-ld20-usb3-ssphy + then: + properties: + clocks: + minItems: 2 + maxItems: 2 + clock-names: + items: + - const: link + - const: phy + resets: + minItems: 2 + maxItems: 2 + reset-names: + items: + - const: link + - const: phy + - if: + properties: + compatible: + contains: + enum: + - socionext,uniphier-pxs3-usb3-ssphy + - socionext,uniphier-nx1-usb3-ssphy + then: + properties: + clocks: + minItems: 2 + maxItems: 3 + clock-names: + minItems: 2 + items: + - const: link + - const: phy + - const: phy-ext + resets: + minItems: 2 + maxItems: 2 + reset-names: + items: + - const: link + - const: phy + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + - resets + - reset-names + +additionalProperties: false + +examples: + - | + usb_ssphy0: phy@300 { + compatible = "socionext,uniphier-ld20-usb3-ssphy"; + reg = <0x300 0x10>; + #phy-cells = <0>; + clock-names = "link", "phy"; + clocks = <&sys_clk 14>, <&sys_clk 16>; + reset-names = "link", "phy"; + resets = <&sys_rst 14>, <&sys_rst 16>; + vbus-supply = <&usb_vbus0>; + }; diff --git a/Documentation/devicetree/bindings/phy/st-spear-miphy.txt b/Documentation/devicetree/bindings/phy/st-spear-miphy.txt new file mode 100644 index 000000000..2a6bfdcc0 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/st-spear-miphy.txt @@ -0,0 +1,15 @@ +ST SPEAr miphy DT details +========================= + +ST Microelectronics SPEAr miphy is a phy controller supporting PCIe and SATA. + +Required properties: +- compatible : should be "st,spear1310-miphy" or "st,spear1340-miphy" +- reg : offset and length of the PHY register set. +- misc: phandle for the syscon node to access misc registers +- #phy-cells : from the generic PHY bindings, must be 1. + - cell[1]: 0 if phy used for SATA, 1 for PCIe. + +Optional properties: +- phy-id: Instance id of the phy. Only required when there are multiple phys + present on a implementation. diff --git a/Documentation/devicetree/bindings/phy/starfive,jh7110-dphy-rx.yaml b/Documentation/devicetree/bindings/phy/starfive,jh7110-dphy-rx.yaml new file mode 100644 index 000000000..7224cde6f --- /dev/null +++ b/Documentation/devicetree/bindings/phy/starfive,jh7110-dphy-rx.yaml @@ -0,0 +1,71 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/starfive,jh7110-dphy-rx.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: StarFive SoC JH7110 MIPI D-PHY Rx Controller + +maintainers: + - Jack Zhu <jack.zhu@starfivetech.com> + - Changhuang Liang <changhuang.liang@starfivetech.com> + +description: + StarFive SoCs contain a MIPI CSI D-PHY based on M31 IP, used to + transfer CSI camera data. + +properties: + compatible: + const: starfive,jh7110-dphy-rx + + reg: + maxItems: 1 + + clocks: + items: + - description: config clock + - description: reference clock + - description: escape mode transmit clock + + clock-names: + items: + - const: cfg + - const: ref + - const: tx + + resets: + items: + - description: DPHY_HW reset + - description: DPHY_B09_ALWAYS_ON reset + + power-domains: + maxItems: 1 + + "#phy-cells": + const: 0 + +required: + - compatible + - reg + - clocks + - clock-names + - resets + - power-domains + - "#phy-cells" + +additionalProperties: false + +examples: + - | + phy@19820000 { + compatible = "starfive,jh7110-dphy-rx"; + reg = <0x19820000 0x10000>; + clocks = <&ispcrg 3>, + <&ispcrg 4>, + <&ispcrg 5>; + clock-names = "cfg", "ref", "tx"; + resets = <&ispcrg 2>, + <&ispcrg 3>; + power-domains = <&aon_syscon 1>; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/starfive,jh7110-pcie-phy.yaml b/Documentation/devicetree/bindings/phy/starfive,jh7110-pcie-phy.yaml new file mode 100644 index 000000000..2e83a6164 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/starfive,jh7110-pcie-phy.yaml @@ -0,0 +1,58 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/starfive,jh7110-pcie-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: StarFive JH7110 PCIe 2.0 PHY + +maintainers: + - Minda Chen <minda.chen@starfivetech.com> + +properties: + compatible: + const: starfive,jh7110-pcie-phy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + starfive,sys-syscon: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to System Register Controller sys_syscon node. + - description: PHY connect offset of SYS_SYSCONSAIF__SYSCFG register for USB PHY. + description: + The phandle to System Register Controller syscon node and the PHY connect offset + of SYS_SYSCONSAIF__SYSCFG register. Connect PHY to USB3 controller. + + starfive,stg-syscon: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to System Register Controller stg_syscon node. + - description: PHY mode offset of STG_SYSCONSAIF__SYSCFG register. + - description: PHY enable for USB offset of STG_SYSCONSAIF__SYSCFG register. + description: + The phandle to System Register Controller syscon node and the offset + of STG_SYSCONSAIF__SYSCFG register for PCIe PHY. Total 2 regsisters offset. + +required: + - compatible + - reg + - "#phy-cells" + +additionalProperties: false + +examples: + - | + phy@10210000 { + compatible = "starfive,jh7110-pcie-phy"; + reg = <0x10210000 0x10000>; + #phy-cells = <0>; + starfive,sys-syscon = <&sys_syscon 0x18>; + starfive,stg-syscon = <&stg_syscon 0x148 0x1f4>; + }; diff --git a/Documentation/devicetree/bindings/phy/starfive,jh7110-usb-phy.yaml b/Documentation/devicetree/bindings/phy/starfive,jh7110-usb-phy.yaml new file mode 100644 index 000000000..269e9f9f1 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/starfive,jh7110-usb-phy.yaml @@ -0,0 +1,50 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/starfive,jh7110-usb-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: StarFive JH7110 USB 2.0 PHY + +maintainers: + - Minda Chen <minda.chen@starfivetech.com> + +properties: + compatible: + const: starfive,jh7110-usb-phy + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + items: + - description: PHY 125m + - description: app 125m + + clock-names: + items: + - const: 125m + - const: app_125m + +required: + - compatible + - reg + - clocks + - clock-names + - "#phy-cells" + +additionalProperties: false + +examples: + - | + phy@10200000 { + compatible = "starfive,jh7110-usb-phy"; + reg = <0x10200000 0x10000>; + clocks = <&syscrg 95>, + <&stgcrg 6>; + clock-names = "125m", "app_125m"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/sunplus,sp7021-usb2-phy.yaml b/Documentation/devicetree/bindings/phy/sunplus,sp7021-usb2-phy.yaml new file mode 100644 index 000000000..57914f214 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/sunplus,sp7021-usb2-phy.yaml @@ -0,0 +1,73 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) Sunplus Co., Ltd. 2021 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/sunplus,sp7021-usb2-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Sunplus SP7021 USB 2.0 PHY Controller + +maintainers: + - Vincent Shih <vincent.sunplus@gmail.com> + +properties: + compatible: + const: sunplus,sp7021-usb2-phy + + reg: + items: + - description: UPHY register region + - description: MOON4 register region + + reg-names: + items: + - const: phy + - const: moon4 + + clocks: + maxItems: 1 + + resets: + maxItems: 1 + + "#phy-cells": + const: 0 + + nvmem-cell-names: + description: names corresponding to the nvmem cells of disconnect voltage + const: disc_vol + + nvmem-cells: + description: nvmem cell address of disconnect voltage + maxItems: 1 + + sunplus,disc-vol-addr-off: + $ref: /schemas/types.yaml#/definitions/uint32 + description: the otp address offset of disconnect voltage + +required: + - compatible + - reg + - reg-names + - clocks + - resets + - "#phy-cells" + - nvmem-cell-names + - nvmem-cells + - sunplus,disc-vol-addr-off + +additionalProperties: false + +examples: + - | + sp_uphy0: usb-phy@9c004a80 { + compatible = "sunplus,sp7021-usb2-phy"; + reg = <0x9c004a80 0x80>, <0x9c000248 0x10>; + reg-names = "phy", "moon4"; + clocks = <&clkc 0x3d>; + resets = <&rstc 0x2d>; + #phy-cells = <0>; + nvmem-cell-names = "disc_vol"; + nvmem-cells = <&disc_vol>; + sunplus,disc-vol-addr-off = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/ti,omap-usb2.yaml b/Documentation/devicetree/bindings/phy/ti,omap-usb2.yaml new file mode 100644 index 000000000..8694b9eb5 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/ti,omap-usb2.yaml @@ -0,0 +1,80 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/ti,omap-usb2.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: OMAP USB2 PHY + +maintainers: + - Kishon Vijay Abraham I <kishon@ti.com> + - Roger Quadros <rogerq@kernel.org> + +properties: + compatible: + oneOf: + - items: + - enum: + - ti,dra7x-usb2 + - ti,dra7x-usb2-phy2 + - ti,am654-usb2 + - enum: + - ti,omap-usb2 + - items: + - const: ti,am437x-usb2 + - items: + - const: ti,omap-usb2 + + reg: + maxItems: 1 + + "#phy-cells": + const: 0 + + clocks: + minItems: 1 + items: + - description: wakeup clock + - description: reference clock + + clock-names: + minItems: 1 + items: + - const: wkupclk + - const: refclk + + syscon-phy-power: + $ref: /schemas/types.yaml#/definitions/phandle-array + items: + - items: + - description: phandle to the system control module + - description: register offset to power on/off the PHY + description: + phandle/offset pair. Phandle to the system control module and + register offset to power on/off the PHY. + + ctrl-module: + $ref: /schemas/types.yaml#/definitions/phandle + description: + (deprecated) phandle of the control module used by PHY driver + to power on the PHY. Use syscon-phy-power instead. + +required: + - compatible + - reg + - "#phy-cells" + - clocks + - clock-names + +additionalProperties: false + +examples: + - | + usb0_phy: phy@4100000 { + compatible = "ti,am654-usb2", "ti,omap-usb2"; + reg = <0x4100000 0x54>; + syscon-phy-power = <&scm_conf 0x4000>; + clocks = <&k3_clks 151 0>, <&k3_clks 151 1>; + clock-names = "wkupclk", "refclk"; + #phy-cells = <0>; + }; diff --git a/Documentation/devicetree/bindings/phy/ti,phy-am654-serdes.yaml b/Documentation/devicetree/bindings/phy/ti,phy-am654-serdes.yaml new file mode 100644 index 000000000..854e554ea --- /dev/null +++ b/Documentation/devicetree/bindings/phy/ti,phy-am654-serdes.yaml @@ -0,0 +1,98 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/ti,phy-am654-serdes.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI AM654 SERDES + +description: + This binding describes the TI AM654 SERDES. AM654 SERDES can be configured + to be used with either PCIe or USB or SGMII. + +maintainers: + - Kishon Vijay Abraham I <kishon@ti.com> + +properties: + compatible: + enum: + - ti,phy-am654-serdes + + reg: + maxItems: 1 + + reg-names: + items: + - const: serdes + + power-domains: + maxItems: 1 + + clocks: + maxItems: 3 + description: + Three input clocks referring to left input reference clock, refclk and right input reference + clock. + + '#phy-cells': + const: 2 + description: + The 1st cell corresponds to the phy type (should be one of the types specified in + include/dt-bindings/phy/phy.h) and the 2nd cell should be the serdes lane function. + + ti,serdes-clk: + description: Phandle to the SYSCON entry required for configuring SERDES clock selection. + $ref: /schemas/types.yaml#/definitions/phandle + + '#clock-cells': + const: 1 + + mux-controls: + maxItems: 1 + description: Phandle to the SYSCON entry required for configuring SERDES lane function. + + clock-output-names: + oneOf: + - description: Clock output names for SERDES 0 + items: + - const: serdes0_cmu_refclk + - const: serdes0_lo_refclk + - const: serdes0_ro_refclk + - description: Clock output names for SERDES 1 + items: + - const: serdes1_cmu_refclk + - const: serdes1_lo_refclk + - const: serdes1_ro_refclk + +required: + - compatible + - reg + - power-domains + - clocks + - assigned-clocks + - assigned-clock-parents + - ti,serdes-clk + - mux-controls + - clock-output-names + +additionalProperties: false + +examples: + - | + #include <dt-bindings/phy/phy-am654-serdes.h> + + serdes0: serdes@900000 { + compatible = "ti,phy-am654-serdes"; + reg = <0x900000 0x2000>; + reg-names = "serdes"; + #phy-cells = <2>; + power-domains = <&k3_pds 153>; + clocks = <&k3_clks 153 4>, <&k3_clks 153 1>, + <&serdes1 AM654_SERDES_LO_REFCLK>; + clock-output-names = "serdes0_cmu_refclk", "serdes0_lo_refclk", "serdes0_ro_refclk"; + assigned-clocks = <&k3_clks 153 4>, <&serdes0 AM654_SERDES_CMU_REFCLK>; + assigned-clock-parents = <&k3_clks 153 8>, <&k3_clks 153 4>; + ti,serdes-clk = <&serdes0_clk>; + mux-controls = <&serdes_mux 0>; + #clock-cells = <1>; + }; diff --git a/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml b/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml new file mode 100644 index 000000000..be41b4547 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/ti,phy-gmii-sel.yaml @@ -0,0 +1,169 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2020 Texas Instruments Incorporated - http://www.ti.com/ +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/ti,phy-gmii-sel.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: CPSW Port's Interface Mode Selection PHY + +maintainers: + - Kishon Vijay Abraham I <kishon@ti.com> + +description: | + TI am335x/am437x/dra7(am5)/dm814x CPSW3G Ethernet Subsystem supports + two 10/100/1000 Ethernet ports with selectable G/MII, RMII, and RGMII interfaces. + The interface mode is selected by configuring the MII mode selection register(s) + (GMII_SEL) in the System Control Module chapter (SCM). GMII_SEL register(s) and + bit fields placement in SCM are different between SoCs while fields meaning + is the same. + +--------------+ + +-------------------------------+ |SCM | + | CPSW | | +---------+ | + | +--------------------------------+gmii_sel | | + | | | | +---------+ | + | +----v---+ +--------+ | +--------------+ + | |Port 1..<--+-->GMII/MII<-------> + | | | | | | | + | +--------+ | +--------+ | + | | | + | | +--------+ | + | | | RMII <-------> + | +--> | | + | | +--------+ | + | | | + | | +--------+ | + | | | RGMII <-------> + | +--> | | + | +--------+ | + +-------------------------------+ + + CPSW Port's Interface Mode Selection PHY describes MII interface mode between + CPSW Port and Ethernet PHY which depends on Eth PHY and board configuration. + | + CPSW Port's Interface Mode Selection PHY device should defined as child device + of SCM node (scm_conf) and can be attached to each CPSW port node using standard + PHY bindings. + +properties: + compatible: + enum: + - ti,am3352-phy-gmii-sel + - ti,dra7xx-phy-gmii-sel + - ti,am43xx-phy-gmii-sel + - ti,dm814-phy-gmii-sel + - ti,am654-phy-gmii-sel + - ti,j7200-cpsw5g-phy-gmii-sel + - ti,j721e-cpsw9g-phy-gmii-sel + - ti,j784s4-cpsw9g-phy-gmii-sel + + reg: + maxItems: 1 + + '#phy-cells': true + + ti,qsgmii-main-ports: + $ref: /schemas/types.yaml#/definitions/uint32-array + description: | + Required only for QSGMII mode. Array to select the port/s for QSGMII + main mode. The size of the array corresponds to the number of QSGMII + interfaces and thus, the number of distinct QSGMII main ports, + supported by the device. If the device supports two QSGMII interfaces + but only one QSGMII interface is desired, repeat the QSGMII main port + value corresponding to the QSGMII interface in the array. + minItems: 1 + maxItems: 2 + items: + minimum: 1 + maximum: 8 + +allOf: + - if: + properties: + compatible: + contains: + enum: + - ti,dra7xx-phy-gmii-sel + - ti,dm814-phy-gmii-sel + - ti,am654-phy-gmii-sel + - ti,j7200-cpsw5g-phy-gmii-sel + - ti,j721e-cpsw9g-phy-gmii-sel + - ti,j784s4-cpsw9g-phy-gmii-sel + then: + properties: + '#phy-cells': + const: 1 + description: CPSW port number (starting from 1) + + - if: + properties: + compatible: + contains: + enum: + - ti,j7200-cpsw5g-phy-gmii-sel + then: + properties: + ti,qsgmii-main-ports: + maxItems: 1 + items: + minimum: 1 + maximum: 4 + + - if: + properties: + compatible: + contains: + enum: + - ti,j721e-cpsw9g-phy-gmii-sel + - ti,j784s4-cpsw9g-phy-gmii-sel + then: + properties: + ti,qsgmii-main-ports: + minItems: 2 + maxItems: 2 + items: + minimum: 1 + maximum: 8 + + - if: + not: + properties: + compatible: + contains: + enum: + - ti,j7200-cpsw5g-phy-gmii-sel + - ti,j721e-cpsw9g-phy-gmii-sel + - ti,j784s4-cpsw9g-phy-gmii-sel + then: + properties: + ti,qsgmii-main-ports: false + + - if: + properties: + compatible: + contains: + enum: + - ti,am3352-phy-gmii-sel + - ti,am43xx-phy-gmii-sel + then: + properties: + '#phy-cells': + const: 2 + description: | + - CPSW port number (starting from 1) + - RMII refclk mode + +required: + - compatible + - reg + - '#phy-cells' + +additionalProperties: false + +examples: + - | + phy_gmii_sel: phy@650 { + compatible = "ti,am3352-phy-gmii-sel"; + reg = <0x650 0x4>; + #phy-cells = <2>; + }; diff --git a/Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml b/Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml new file mode 100644 index 000000000..3f16ff144 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml @@ -0,0 +1,259 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +# Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/ +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/ti,phy-j721e-wiz.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TI J721E WIZ (SERDES Wrapper) + +maintainers: + - Kishon Vijay Abraham I <kishon@ti.com> + +properties: + compatible: + enum: + - ti,j721e-wiz-16g + - ti,j721e-wiz-10g + - ti,j721s2-wiz-10g + - ti,am64-wiz-10g + - ti,j7200-wiz-10g + - ti,j784s4-wiz-10g + + power-domains: + maxItems: 1 + + clocks: + minItems: 3 + maxItems: 4 + description: clock-specifier to represent input to the WIZ + + clock-names: + minItems: 3 + items: + - const: fck + - const: core_ref_clk + - const: ext_ref_clk + - const: core_ref1_clk + + num-lanes: + minimum: 1 + maximum: 4 + + "#address-cells": + const: 1 + + "#size-cells": + const: 1 + + "#reset-cells": + const: 1 + + "#clock-cells": + const: 1 + + ranges: true + + typec-dir-gpios: + maxItems: 1 + description: + GPIO to signal Type-C cable orientation for lane swap. + If GPIO is active, lane 0 and lane 1 of SERDES will be swapped to + achieve the functionality of an external type-C plug flip mux. + + typec-dir-debounce-ms: + minimum: 100 + maximum: 1000 + default: 100 + description: + Number of milliseconds to wait before sampling typec-dir-gpio. + If not specified, the default debounce of 100ms will be used. + Type-C spec states minimum CC pin debounce of 100 ms and maximum + of 200 ms. However, some solutions might need more than 200 ms. + + refclk-dig: + type: object + additionalProperties: false + description: | + WIZ node should have subnode for refclk_dig to select the reference + clock source for the reference clock used in the PHY and PMA digital + logic. + deprecated: true + properties: + clocks: + minItems: 2 + maxItems: 4 + description: Phandle to two (Torrent) or four (Sierra) clock nodes representing + the inputs to refclk_dig + + "#clock-cells": + const: 0 + + clock-output-names: + maxItems: 1 + + assigned-clocks: + maxItems: 1 + + assigned-clock-parents: + maxItems: 1 + + required: + - clocks + - "#clock-cells" + - assigned-clocks + - assigned-clock-parents + + ti,scm: + $ref: /schemas/types.yaml#/definitions/phandle + description: | + phandle to System Control Module for syscon regmap access. + +patternProperties: + "^pll[0|1]-refclk$": + type: object + additionalProperties: false + description: | + WIZ node should have subnodes for each of the PLLs present in + the SERDES. + deprecated: true + properties: + clocks: + maxItems: 2 + description: Phandle to clock nodes representing the two inputs to PLL. + + "#clock-cells": + const: 0 + + clock-output-names: + maxItems: 1 + + assigned-clocks: + maxItems: 1 + + assigned-clock-parents: + maxItems: 1 + + required: + - clocks + - "#clock-cells" + - assigned-clocks + - assigned-clock-parents + + "^cmn-refclk1?-dig-div$": + type: object + additionalProperties: false + description: + WIZ node should have subnodes for each of the PMA common refclock + provided by the SERDES. + deprecated: true + properties: + clocks: + maxItems: 1 + description: Phandle to the clock node representing the input to the + divider clock. + + "#clock-cells": + const: 0 + + clock-output-names: + maxItems: 1 + + required: + - clocks + - "#clock-cells" + + "^serdes@[0-9a-f]+$": + type: object + description: | + WIZ node should have '1' subnode for the SERDES. It could be either + Sierra SERDES or Torrent SERDES. Sierra SERDES should follow the + bindings specified in + Documentation/devicetree/bindings/phy/phy-cadence-sierra.yaml + Torrent SERDES should follow the bindings specified in + Documentation/devicetree/bindings/phy/phy-cadence-torrent.yaml + +required: + - compatible + - power-domains + - clocks + - clock-names + - num-lanes + - "#address-cells" + - "#size-cells" + - "#reset-cells" + - ranges + +allOf: + - if: + properties: + compatible: + contains: + const: ti,j7200-wiz-10g + then: + required: + - ti,scm + +additionalProperties: false + +examples: + - | + #include <dt-bindings/soc/ti,sci_pm_domain.h> + + wiz@5000000 { + compatible = "ti,j721e-wiz-16g"; + #address-cells = <1>; + #size-cells = <1>; + power-domains = <&k3_pds 292 TI_SCI_PD_EXCLUSIVE>; + clocks = <&k3_clks 292 5>, <&k3_clks 292 11>, <&dummy_cmn_refclk>; + clock-names = "fck", "core_ref_clk", "ext_ref_clk"; + assigned-clocks = <&k3_clks 292 11>, <&k3_clks 292 0>; + assigned-clock-parents = <&k3_clks 292 15>, <&k3_clks 292 4>; + num-lanes = <2>; + #reset-cells = <1>; + ranges = <0x5000000 0x5000000 0x10000>; + + pll0-refclk { + clocks = <&k3_clks 293 13>, <&dummy_cmn_refclk>; + #clock-cells = <0>; + assigned-clocks = <&wiz1_pll0_refclk>; + assigned-clock-parents = <&k3_clks 293 13>; + }; + + pll1-refclk { + clocks = <&k3_clks 293 0>, <&dummy_cmn_refclk1>; + #clock-cells = <0>; + assigned-clocks = <&wiz1_pll1_refclk>; + assigned-clock-parents = <&k3_clks 293 0>; + }; + + cmn-refclk-dig-div { + clocks = <&wiz1_refclk_dig>; + #clock-cells = <0>; + }; + + cmn-refclk1-dig-div { + clocks = <&wiz1_pll1_refclk>; + #clock-cells = <0>; + }; + + refclk-dig { + clocks = <&k3_clks 292 11>, <&k3_clks 292 0>, + <&dummy_cmn_refclk>, <&dummy_cmn_refclk1>; + #clock-cells = <0>; + assigned-clocks = <&wiz0_refclk_dig>; + assigned-clock-parents = <&k3_clks 292 11>; + }; + + serdes@5000000 { + compatible = "ti,sierra-phy-t0"; + reg-names = "serdes"; + reg = <0x5000000 0x10000>; + #address-cells = <1>; + #size-cells = <0>; + resets = <&serdes_wiz0 0>; + reset-names = "sierra_reset"; + clocks = <&wiz0_cmn_refclk_dig_div>, <&wiz0_cmn_refclk1_dig_div>; + clock-names = "cmn_refclk_dig_div", "cmn_refclk1_dig_div"; + }; + }; diff --git a/Documentation/devicetree/bindings/phy/ti,tcan104x-can.yaml b/Documentation/devicetree/bindings/phy/ti,tcan104x-can.yaml new file mode 100644 index 000000000..79dad3e89 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/ti,tcan104x-can.yaml @@ -0,0 +1,64 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/ti,tcan104x-can.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: TCAN104x CAN TRANSCEIVER PHY + +maintainers: + - Aswath Govindraju <a-govindraju@ti.com> + +properties: + $nodename: + pattern: "^can-phy" + + compatible: + enum: + - nxp,tjr1443 + - ti,tcan1042 + - ti,tcan1043 + + '#phy-cells': + const: 0 + + standby-gpios: + description: + gpio node to toggle standby signal on transceiver + maxItems: 1 + + enable-gpios: + description: + gpio node to toggle enable signal on transceiver + maxItems: 1 + + max-bitrate: + $ref: /schemas/types.yaml#/definitions/uint32 + description: + max bit rate supported in bps + minimum: 1 + + mux-states: + description: + mux controller node to route the signals from controller to + transceiver. + maxItems: 1 + +required: + - compatible + - '#phy-cells' + +additionalProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + + transceiver1: can-phy { + compatible = "ti,tcan1043"; + #phy-cells = <0>; + max-bitrate = <5000000>; + standby-gpios = <&wakeup_gpio1 16 GPIO_ACTIVE_LOW>; + enable-gpios = <&main_gpio1 67 GPIO_ACTIVE_HIGH>; + mux-states = <&mux0 1>; + }; diff --git a/Documentation/devicetree/bindings/phy/ti-phy.txt b/Documentation/devicetree/bindings/phy/ti-phy.txt new file mode 100644 index 000000000..7c7936b89 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/ti-phy.txt @@ -0,0 +1,98 @@ +TI PHY: DT DOCUMENTATION FOR PHYs in TI PLATFORMs + +OMAP CONTROL PHY + +Required properties: + - compatible: Should be one of + "ti,control-phy-otghs" - if it has otghs_control mailbox register as on OMAP4. + "ti,control-phy-usb2" - if it has Power down bit in control_dev_conf register + e.g. USB2_PHY on OMAP5. + "ti,control-phy-pipe3" - if it has DPLL and individual Rx & Tx power control + e.g. USB3 PHY and SATA PHY on OMAP5. + "ti,control-phy-pcie" - for pcie to support external clock for pcie and to + set PCS delay value. + e.g. PCIE PHY in DRA7x + "ti,control-phy-usb2-dra7" - if it has power down register like USB2 PHY on + DRA7 platform. + "ti,control-phy-usb2-am437" - if it has power down register like USB2 PHY on + AM437 platform. + - reg : register ranges as listed in the reg-names property + - reg-names: "otghs_control" for control-phy-otghs + "power", "pcie_pcs" and "control_sma" for control-phy-pcie + "power" for all other types + +omap_control_usb: omap-control-usb@4a002300 { + compatible = "ti,control-phy-otghs"; + reg = <0x4a00233c 0x4>; + reg-names = "otghs_control"; +}; + +TI PIPE3 PHY + +Required properties: + - compatible: Should be "ti,phy-usb3", "ti,phy-pipe3-sata" or + "ti,phy-pipe3-pcie. "ti,omap-usb3" is deprecated. + - reg : Address and length of the register set for the device. + - reg-names: The names of the register addresses corresponding to the registers + filled in "reg". + - #phy-cells: determine the number of cells that should be given in the + phandle while referencing this phy. + - clocks: a list of phandles and clock-specifier pairs, one for each entry in + clock-names. + - clock-names: should include: + * "wkupclk" - wakeup clock. + * "sysclk" - system clock. + * "refclk" - reference clock. + * "dpll_ref" - external dpll ref clk + * "dpll_ref_m2" - external dpll ref clk + * "phy-div" - divider for apll + * "div-clk" - apll clock + +Optional properties: + - id: If there are multiple instance of the same type, in order to + differentiate between each instance "id" can be used (e.g., multi-lane PCIe + PHY). If "id" is not provided, it is set to default value of '1'. + - syscon-pllreset: Handle to system control region that contains the + CTRL_CORE_SMA_SW_0 register and register offset to the CTRL_CORE_SMA_SW_0 + register that contains the SATA_PLL_SOFT_RESET bit. Only valid for sata_phy. + - syscon-pcs : phandle/offset pair. Phandle to the system control module and the + register offset to write the PCS delay value. + +Deprecated properties: + - ctrl-module : phandle of the control module used by PHY driver to power on + the PHY. + +Recommended properties: + - syscon-phy-power : phandle/offset pair. Phandle to the system control + module and the register offset to power on/off the PHY. + +This is usually a subnode of ocp2scp to which it is connected. + +usb3phy@4a084400 { + compatible = "ti,phy-usb3"; + reg = <0x4a084400 0x80>, + <0x4a084800 0x64>, + <0x4a084c00 0x40>; + reg-names = "phy_rx", "phy_tx", "pll_ctrl"; + ctrl-module = <&omap_control_usb>; + #phy-cells = <0>; + clocks = <&usb_phy_cm_clk32k>, + <&sys_clkin>, + <&usb_otg_ss_refclk960m>; + clock-names = "wkupclk", + "sysclk", + "refclk"; +}; + +sata_phy: phy@4a096000 { + compatible = "ti,phy-pipe3-sata"; + reg = <0x4A096000 0x80>, /* phy_rx */ + <0x4A096400 0x64>, /* phy_tx */ + <0x4A096800 0x40>; /* pll_ctrl */ + reg-names = "phy_rx", "phy_tx", "pll_ctrl"; + ctrl-module = <&omap_control_sata>; + clocks = <&sys_clkin1>, <&sata_ref_clk>; + clock-names = "sysclk", "refclk"; + syscon-pllreset = <&scm_conf 0x3fc>; + #phy-cells = <0>; +}; diff --git a/Documentation/devicetree/bindings/phy/transmit-amplitude.yaml b/Documentation/devicetree/bindings/phy/transmit-amplitude.yaml new file mode 100644 index 000000000..617f3c0b3 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/transmit-amplitude.yaml @@ -0,0 +1,103 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/transmit-amplitude.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common PHY and network PCS transmit amplitude property + +description: + Binding describing the peak-to-peak transmit amplitude for common PHYs + and network PCSes. + +maintainers: + - Marek BehĂșn <kabel@kernel.org> + +properties: + tx-p2p-microvolt: + description: + Transmit amplitude voltages in microvolts, peak-to-peak. If this property + contains multiple values for various PHY modes, the + 'tx-p2p-microvolt-names' property must be provided and contain + corresponding mode names. + + tx-p2p-microvolt-names: + description: | + Names of the modes corresponding to voltages in the 'tx-p2p-microvolt' + property. Required only if multiple voltages are provided. + + If a value of 'default' is provided, the system should use it for any PHY + mode that is otherwise not defined here. If 'default' is not provided, the + system should use manufacturer default value. + minItems: 1 + maxItems: 16 + items: + enum: + - default + + # ethernet modes + - sgmii + - qsgmii + - xgmii + - 1000base-x + - 2500base-x + - 5gbase-r + - rxaui + - xaui + - 10gbase-kr + - usxgmii + - 10gbase-r + - 25gbase-r + + # PCIe modes + - pcie + - pcie1 + - pcie2 + - pcie3 + - pcie4 + - pcie5 + - pcie6 + + # USB modes + - usb + - usb-ls + - usb-fs + - usb-hs + - usb-ss + - usb-ss+ + - usb-4 + + # storage modes + - sata + - ufs-hs + - ufs-hs-a + - ufs-hs-b + + # display modes + - lvds + - dp + - dp-rbr + - dp-hbr + - dp-hbr2 + - dp-hbr3 + - dp-uhbr-10 + - dp-uhbr-13.5 + - dp-uhbr-20 + + # camera modes + - mipi-dphy + - mipi-dphy-univ + - mipi-dphy-v2.5-univ + +dependencies: + tx-p2p-microvolt-names: [ tx-p2p-microvolt ] + +additionalProperties: true + +examples: + - | + phy: phy { + #phy-cells = <1>; + tx-p2p-microvolt = <915000>, <1100000>, <1200000>; + tx-p2p-microvolt-names = "2500base-x", "usb-hs", "usb-ss"; + }; diff --git a/Documentation/devicetree/bindings/phy/xlnx,zynqmp-psgtr.yaml b/Documentation/devicetree/bindings/phy/xlnx,zynqmp-psgtr.yaml new file mode 100644 index 000000000..cefbc8b53 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/xlnx,zynqmp-psgtr.yaml @@ -0,0 +1,105 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/phy/xlnx,zynqmp-psgtr.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx ZynqMP Gigabit Transceiver PHY + +maintainers: + - Laurent Pinchart <laurent.pinchart@ideasonboard.com> + +description: | + This binding describes the Xilinx ZynqMP Gigabit Transceiver (GTR) PHY. The + GTR provides four lanes and is used by USB, SATA, PCIE, Display port and + Ethernet SGMII controllers. + +properties: + "#phy-cells": + const: 4 + description: | + The cells contain the following arguments. + + - description: The GTR lane + minimum: 0 + maximum: 3 + - description: The PHY type + enum: + - PHY_TYPE_DP + - PHY_TYPE_PCIE + - PHY_TYPE_SATA + - PHY_TYPE_SGMII + - PHY_TYPE_USB3 + - description: The PHY instance + minimum: 0 + maximum: 1 # for DP, SATA or USB + maximum: 3 # for PCIE or SGMII + - description: The reference clock number + minimum: 0 + maximum: 3 + + compatible: + enum: + - xlnx,zynqmp-psgtr-v1.1 + - xlnx,zynqmp-psgtr + + clocks: + minItems: 1 + maxItems: 4 + description: | + Clock for each PS_MGTREFCLK[0-3] reference clock input. Unconnected + inputs shall not have an entry. + + clock-names: + minItems: 1 + maxItems: 4 + items: + pattern: "^ref[0-3]$" + + reg: + items: + - description: SERDES registers block + - description: SIOU registers block + + reg-names: + items: + - const: serdes + - const: siou + + xlnx,tx-termination-fix: + description: | + Include this for fixing functional issue with the TX termination + resistance in GT, which can be out of spec for the XCZU9EG silicon + version. + type: boolean + +required: + - "#phy-cells" + - compatible + - reg + - reg-names + +if: + properties: + compatible: + const: xlnx,zynqmp-psgtr-v1.1 + +then: + properties: + xlnx,tx-termination-fix: false + +additionalProperties: false + +examples: + - | + phy: phy@fd400000 { + compatible = "xlnx,zynqmp-psgtr-v1.1"; + reg = <0xfd400000 0x40000>, + <0xfd3d0000 0x1000>; + reg-names = "serdes", "siou"; + clocks = <&refclks 3>, <&refclks 2>, <&refclks 0>; + clock-names = "ref1", "ref2", "ref3"; + #phy-cells = <4>; + }; + +... |